| Age | Commit message (Collapse) | Author |
|---|
|
SATA is routed to PIRQG which should be interrupt 22
and not interrupt 21. The kernel uses MSI with this
device so this is only seen when booting with pci=nomsi
Change-Id: Ic90ca2c561fc4c53ec1d395c05872222c65ff98a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63796
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4398
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The SystemAgent contains a mini-hd audio controller at PCI 0:3.0
which uses the same verb table init sequence as the southbridge.
In order to avoid two copies of the verb table loading code I
separated out the HDA verb table functions into a file that can
be re-used and then added a minihd driver to the haswell northbridge.
The minihd verb table is the same across devices so it can live
within the minihd driver rather than needing to be specified in
each separate mainboard.
I also fixed up the driver for lynxpoint HDA by following the
reference code.
Without HDMI cable plugged in driver does not find any codec,
and it does not seem to re-probe when HDMI is connected. We may
be missing kernel patches for this.
hda-intel 0000:00:03.0: no codecs found!
With a basic kernel patch to add 0x0a0c device ID to HDA driver
and with HDMI cable connected it is much happier:
snd_hda_intel 0000:00:03.0: irq 60 for MSI/MSI-X
input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input9
snd_hda_intel 0000:00:1b.0: irq 61 for MSI/MSI-X
input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input10
input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input11
Change-Id: Ifa587984be4fc2801704a0368b9cdf8379c2450e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59336
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4318
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The drivers are designed to work with an edge triggered interrupt.
Change-Id: I35a121ecfb6409bb9049f4d1e034185bb3bb7557
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61664
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4360
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Limit power to 12W at 73C and remove limit at 68C.
To have the CPU consume maximum power it is necessary to stress
both the CPU and the GPU. Bastion (chrome.supergiantgames.com)
and/or webglsamples.googlecode.com can be useful for this.
Testing this properly requires a script to report the running
average power readings. The watch_power.sh script is attached
to this issue in the partner tracker.
1) Run watch_power.sh continuously:
localhost ~ # watch -n 0 bash -e /tmp/watch_power.sh
2) Start Bastion (or other stress apps). The power draw should
be close to 15W if under enough load.
3) Watch until temperature climbs above 73C and is caught by
the thermal zone 10 second poll, this can be sped up by blocking
or removing the fan.
4) The ACPI thermal zone states should change to reflect that
active[2] is now enabled and power consumption should drop to 12W.
5) Stop the stress apps and wait until the CPU cools off again,
enable the fan again if it was removed.
6) The ACPI thermal zone state should switch back to active[3].
Change-Id: Ie6714a8543d4f06edf8513086fc9c968273bdb23
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60545
Reviewed-on: http://review.coreboot.org/4335
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The OIPG package needs to have >1 member to make the chromeos_acpi
kernel driver do the right automagic sysfs topology creation.
Additionally an "unimplemented" GPIO should be reported as 0xFF
because 0 is a valid GPIO number.
verify crossystem on slippy
$ sudo crossystem | grep -e recoverysw_cur -e wpsw_cur
recoverysw_cur = (error)
wpsw_cur = 1
Change-Id: I06dff09152bde30a3ffe58b1defe9d299155472c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57471
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4221
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Add HDA verb table
- Add on-board device table
- Add panel power sequencing values
Change-Id: I1b3450c2740ec1d930f157a9b23550e1efc8668f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58197
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4233
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Taken directly from slippy with only constant + string changes.
(Peppy port of I4172460d3b075bfd5bb22013a6225cf0e8f95b9c by dlaurie)
The following changes are required in a subsequent commit:
- Add Elpida SPD data.
- Update GPIO map.
- Remove iSSD power sequencing.
- Update USB port map.
Change-Id: I01dfb841f0e9186cf8a0a23f72e7be986a83be42
Reviewed-on: https://gerrit.chromium.org/gerrit/56513
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4200
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
