aboutsummaryrefslogtreecommitdiff
path: root/src/mainboard/google/octopus/variants/fleex
AgeCommit message (Collapse)Author
2020-11-13mb/google/octopus: Configure IRQs as level triggered for HID over I2CKarthikeyan Ramasubramanian
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4, the interrupt line used by the device is required to be level triggered. Hence, this change updates the configuration of the HID over I2C devices to be level triggered. References: [1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx BUG=b:172846122 TEST=./util/abuild/abuild Change-Id: Ic334816712370da63471135da8dd598ab02d54ef Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47421 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-11-02mb/google/octopus/var/fleex: Add variant.c into smm stageEric Lai
variant_smi_sleep is called in smm stage so we need to add variant.c into smm stage. Otherwise it will call the dummy one. BUG=b:168075958 BRANCH=octopus TEST=build image passed. Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I41df1a30b119ab3e04f9ae01955b6044f137527f Reviewed-on: https://review.coreboot.org/c/coreboot/+/46847 Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com> Reviewed-by: Marco Chen <marcochen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-10-30mb/google/octopus/var/fleex: Disable XHCI LFPS power management by skuEric Lai
LTE module Fibocom L850-GL is lost after idle overnight, with this workaround, host will not initiate U3 wakeup at the same time with device, which will avoid the race condition. If this option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR + offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0. BUG=b:169645448 BRANCH=octopus TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash the image to the device. Run following command to check if bits[7:4] is set 0: >iotools mmio_read32 "XHCI MMIO BAR + 0x80A4" Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I3a04320b0e2441dce540a5afdc461f12de45c41b Reviewed-on: https://review.coreboot.org/c/coreboot/+/46868 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marco Chen <marcochen@google.com>
2020-10-26mb/google/octopus/var/fleex: Add goodix touch pad supportEric Lai
Add goodix touch pad as below: HWID : GXTP7288 CID : PNP0C50 I2C address : 0x2C I2C speed : 400Khz HID Descriptor Address : 0x20 BUG=b:171351666 BRANCH=octopus TEST=build image and verify goodix touch pad working. Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: Idb4f8d3aff09712dcc98c8ae0c9ae30dc4049e29 Reviewed-on: https://review.coreboot.org/c/coreboot/+/46614 Reviewed-by: Marco Chen <marcochen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-10-26mb/google/octopus/var/fleex: Add new SKU for LTE touchAmanda Huang
New SKU ID 5 is used for LTE touch SKU. This patch does LTE power off for LTE sku and only use Wifi SAR table for non-LTE sku. BUG=b:168001586 BRANCH=octopus TEST=Check no SAR table can be loaded with sku id 4 and 5. Change-Id: Ic0405d3e52aa813bbb1f350966a9e2825e595ce4 Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46643 Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-10-05Fleex: Resume from suspend on critical batteryDaisuke Nojiri
This patch makes Fleex EC wake up AP from s0ix when the state of charge drops to 5%. Demonstrated as follows: 1. Boot Fleex. 2. Run powerd_dbus_suspend. 3. On EC, run battfake 5. 4. System resumes. BUG=b:163721887 BRANCH=Octopus TEST=Verified on Fleex: Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Change-Id: I4a998ad0aef5a7cfc6fd18995bde5571e6127e77 Reviewed-on: https://review.coreboot.org/c/coreboot/+/45967 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
2020-09-28mb/google/octopus/variants/fleex: Only do LTE power off for LTE skuEric Lai
Only do LTE power off for LTE sku in order to save extra 130ms delay for non-LTE sku. BUG=b:168075958 BRANCH=octopus TEST=build image and verify on the DUT with LTE DB. Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: If983185ff2f09fb1b2553c6ff1a1473d3254de4b Reviewed-on: https://review.coreboot.org/c/coreboot/+/45687 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marco Chen <marcochen@google.com>
2020-09-28mb/google/octopus/var/fleex: Use Wifi SAR table for non-LTE sku onlyEric Lai
Use Wifi SAR table for non-LTE sku only. BUG=b:169115341 BRANCH=octopus TEST=Check no SAR table can be loaded with sku id 4. Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I086fa14a9f23e4a0fc0ef8085040219c932dbf17 Reviewed-on: https://review.coreboot.org/c/coreboot/+/45640 Reviewed-by: Marco Chen <marcochen@google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-09-21mb/google/octopus: Clean up LTE power off functionEric Lai
All octopus board share the same power off sequence. Move to smihandler.c instead variant.c. BUG=b:168075958 BRANCH=octopus TEST=build image and verify on the DUT with LTE DB. Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I2be5a656fb42fff99c56d21aaa73ed9140caad37 Reviewed-on: https://review.coreboot.org/c/coreboot/+/45436 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-09-18mb/google/octopus/variants/fleex: support LTE power sequenceEric Lai
GPIOs related to power sequence are GPIO_67 - EN_PP3300 GPIO_117 - FULL_CARD_POWER_ON_OFF GPIO_161 - PLT_RST_LTE_L 1. Power on: GPIO_67 -> 0ms -> GPIO_117 -> 30ms -> GPIO_161 2. Power off: GPIO_161 -> 30ms -> GPIO_117 -> 100ms -> GPIO_67 3. Power reset: - keep GPIO_67 and GPIO_117 high and - pull down GPIO_161 for 30ms then release it. BUG=b:168075958 BRANCH=octopus TEST=build image and verify on the DUT with LTE DB. Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I9b56ef8ff346c1d4edd5aad04d4a7396c4702ffc Reviewed-on: https://review.coreboot.org/c/coreboot/+/45193 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Henry Sun <henrysun@google.com> Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-09-14mb/google/octopus/variants/fleex: Add G2Touch touchscreen supportJohn Su
BUG=b:167297664 BRANCH=octopus TEST=build fleex, and check touchscreen can work Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Change-Id: I910681c258ff5487830e795a8bd08c66be69b1d4 Reviewed-on: https://review.coreboot.org/c/coreboot/+/44980 Reviewed-by: Justin TerAvest <teravest@google.com> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Marco Chen <marcochen@google.com> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: Henry Sun <henrysun@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-11treewide: Remove "this file is part of" linesPatrick Georgi
Stefan thinks they don't add value. Command used: sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool) The exceptions are for: - crossgcc (patch file) - gcov (imported from gcc) - elf.h (imported from GNU's libc) - nvramtool (more complicated header) The removed lines are: - fmt.Fprintln(f, "/* This file is part of the coreboot project. */") -# This file is part of a set of unofficial pre-commit hooks available -/* This file is part of coreboot */ -# This file is part of msrtool. -/* This file is part of msrtool. */ - * This file is part of ncurses, designed to be appended after curses.h.in -/* This file is part of pgtblgen. */ - * This file is part of the coreboot project. - /* This file is part of the coreboot project. */ -# This file is part of the coreboot project. -# This file is part of the coreboot project. -## This file is part of the coreboot project. --- This file is part of the coreboot project. -/* This file is part of the coreboot project */ -/* This file is part of the coreboot project. */ -;## This file is part of the coreboot project. -# This file is part of the coreboot project. It originated in the - * This file is part of the coreinfo project. -## This file is part of the coreinfo project. - * This file is part of the depthcharge project. -/* This file is part of the depthcharge project. */ -/* This file is part of the ectool project. */ - * This file is part of the GNU C Library. - * This file is part of the libpayload project. -## This file is part of the libpayload project. -/* This file is part of the Linux kernel. */ -## This file is part of the superiotool project. -/* This file is part of the superiotool project */ -/* This file is part of uio_usbdebug */ Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194 Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-04-06mb/google/octopus: Use SPDX for GPL-2.0-only filesAngel Pons
Done with sed and God Lines. Only done for C-like code for now. Change-Id: I8076155330100982de82d410b6579ac99ed89e7b Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40187 Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-03-18mainboard/google: Remove copyright noticesPatrick Georgi
They're listed in AUTHORS and often incorrect anyway, for example: - What's a "Copyright $year-present"? - Which incarnation of Google (Inc, LLC, ...) is the current copyright holder? - People sometimes have their editor auto-add themselves to files even though they only deleted stuff - Or they let the editor automatically update the copyright year, because why not? - Who is the copyright holder "The coreboot project Authors"? - Or "Generated Code"? Sidestep all these issues by simply not putting these notices in individual files, let's list all copyright holders in AUTHORS instead and use the git history to deal with the rest. Change-Id: I09cc279b1f75952bb397de2c3f2b299255163685 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/39607 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: David Hendricks <david.hendricks@gmail.com>
2019-10-10mb/google/octopus/variants/fleex: Update GPIOs to fix EMRJohn Su
Update GPIO_138 and GPIO_139 setting to fix EMR function. BUG=b:141729962,b:141281846 BRANCH=octopus TEST=verify EMR function in Grob360S. Change-Id: I28cef592374fb4aeee2f3d3010cc0e237d62a2fd Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35881 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marco Chen <marcochen@google.com> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-10-07mb/google/octopus/variants/fleex: Adjust I2C0 CLK to meet specJohn Su
After adjustment on Grob360S I2C0 CLK: 389.9 KHz BUG=b:141729962 BRANCH=master TEST=emerge-octopus coreboot chromeos-bootimage measure by scope with Grob360S. Change-Id: I6a30257b7978cc8899a55f9fd6ffffe01cb2a851 Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35788 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
2019-07-23mb/google/octopus/variants/fleex: Remove gpio NC setting for enabling I2C0Frank Wu
Enable I2C0 in fleex then verify EMR function successfully BUG=b:135968368 BRANCH=octopus TEST=EMR function working normally with I2C0 in Grob360S. Change-Id: I784ff32418bc839bcec14fbfd7236f708828690e Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34364 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marco Chen <marcochen@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2019-07-03mb/google/octopus/variants/fleex: Enable EMR function for Grob360SChris Zhou
Enable EMR Pen Stylus function for Grob360S BUG=b:135968368 BRANCH=octopus TEST=EMR function working normally with HW reworked Fleex. Change-Id: Ia220dc0d3051b79b110b4df66df108f701776478 Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33802 Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-04-18mb/google/octopus: Set default configuration to low for gpio_178Wisley Chen
Set default configuration to low for gpio_178, and can remove the override setting for bobba/bloog/fleex/meep/phaser. For ampton, Change-Id I64a67f73564188ad0548a1a770169ef2bca47453 ( mb/google/ampton: Fix polarity of EN_PP3300_WLAN_L signal.) modified the pin setting. TEST=verified that boot into OS on meep board. suspend/resume, reboot, and no failure found. Change-Id: I7668ff4817edfca5c6cea63db779fcea21c7af92 Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32247 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-28mb/google/octopus: Fix termination for unused dual voltage pinsShamile Khan
These pins should not have pull downs configured in standby state as that can cause contention on the termination circuitry and lead to incorrect behavior as per Doc# 572688 Gemini Lake Processor GPIOTermination Configuration. BUG=b:79982669 TEST=Checked that code compiles with changes. Change-Id: If3cadc000ec6fc56019ee3f57e556dc819d5e0a5 Signed-off-by: Shamile Khan <shamile.khan@intel.com> Reviewed-on: https://review.coreboot.org/c/30823 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-01-20mb/google/octopus/variants: Disable xHCI compliance mode for FleexAmanda Huang
Some usb devices exhibits signal loss which causes xHCI entering compliance mode. The resolution is to disable xHCI compliance mode. BRANCH=octopus BUG=b:120009029 TEST=Verified usb operation successfully. Change-Id: Ic7fa08c894397598dee3c4ff9a764e43383a0627 Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/30984 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2019-01-10mainboard/google/octopus: configure EC_AP_INT_ODLJett Rink
Enable the EC_AP_INT_ODL interrupt on GPIO_134 for all octopus boards that support it. Also removing unnecessary IO standby support since we don't use this pin to wake up the SoC. BRANCH=octopus BUG=b:122552125,b:120679547 TEST=CTS tests with changes Change-Id: I018864ae5fa400372b5b443e49828e8202b9aa4d Signed-off-by: Jett Rink <jettrink@chromium.org> Reviewed-on: https://review.coreboot.org/c/30788 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-29mb/google/octopus: Override emmc DLL values for FleexBora Guvendik
New emmc DLL values for Fleex. BUG=b:120561055 TEST=Boot to OS, chromeos-install, mmc_test Change-Id: Id0022e9d0f0a7802113bbf193decff3c8aaa04f8 Signed-off-by: Bora Guvendik <bora.guvendik@intel.com> Reviewed-on: https://review.coreboot.org/c/30226 Reviewed-by: Justin TerAvest <teravest@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-12-24Revert "mb/google/octopus/variants/fleex: Update Charger throttling settings"Sumeet Pawnikar
This reverts commit 969ed357f823659a6861a2ca38f3ad9d7b58f949 Reason for revert: According to partner issue b:112448519 comment#80, it impacts skin temperature specifications. Change-Id: I7603c3816f34adebc1f67eff6fad214557544022 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/c/30366 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Justin TerAvest <teravest@chromium.org>
2018-12-17mb/google/octopus/variants/fleex: Update Charger throttling settingsSumeet Pawnikar
Update dptf settings for Charger throttling. Also, update Power Limit1 minimum value setting from 4.5W to 3W. BUG=b:112448519 BRANCH=octopus TEST=Built and tested on Fleex system Change-Id: I8c2a796ff28254ebef28ed5745b344f925d6e649 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/c/30080 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org>
2018-11-27mb/google/octopus/var/fleex: Deprecate bid 0Furquan Shaikh
This change gets rid of bid0_override_table as part of clean up effort to deprecate bid0. Additionally, it updates the touchscreen enable GPIO in overridetree and gets rid of variant.c to update enable gpio at runtime. BUG=b:119885949 Change-Id: If14abb324d9422720ca4d0f0859e092319d454ee Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/29785 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Justin TerAvest <teravest@chromium.org>
2018-11-27mb/google/octopus: Update GPIO_178 in early_gpio_table in baseboardFurquan Shaikh
This change updates the configuration of GPIO_178 to be active low as per latest revision on different octopus variants. This effectively: 1. Gets rid of early_gpio_table in different variants -- phaser, meep, fleex, bobba. 2. Deprecates board id < 2 for bobba, board id < 1 for fleex and phaser. 3. Adds special early_gpio_table in yorp which has GPIO_178 as an active high signal. BUG=b:119885949 Change-Id: I024199a8f1f96db57f8fa60c4d265789cd3a0493 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/29784 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Justin TerAvest <teravest@chromium.org>
2018-11-12mb/google/octopus/variants/fleex: Set up tcc offset for fleexJohn Su
Change tcc offset from 0 to 10 for fleex. Refer to b:117789732#1 BUG=b:117789732 TEST=Match the result from TAT UI Change-Id: I481526ab10a16a33fe0cf9528b52b8524e012451 Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29413 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-10-24mb/google/octopus/variants/fleex: Update DPTF parametersJohn Su
1. Update PSV values for cpu and sensers. 2. Change PL1 min value from 3w to 4.5w. 3. Change TSR2 TRT source from charger to CPU. Refer to 112448519#comment31. BUG=b:112448519 TEST=Build coreboot for Octopus board Change-Id: I7c7df0f54374fdaa4cf57d5c255d841d7db38cfc Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/29146 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
2018-10-23mb/google/octopus: Use a single GPIO for trackpad wake and IRQFurquan Shaikh
This change uses the newly added macros for configuring the same GPI pad(GPIO_135) for IRQ (normal interrupt operations) and wake (interrupt for waking from S3/S0ix) for the trackpad device. The other pad GPIO_142 is now configured as not connected. BUG=b:117553222 TEST=Verified that yorp and bobba wake from S3 and S0ix using trackpad. Change-Id: I2b704f1be493141629c647b79723b0025b0f7dd6 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/29189 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-10-06mb/google/octopus/variants/fleex: Disable I2C0 in devicetreeFurquan Shaikh
Fleex does not have any device on I2C0 and hence this change disables I2C0 device (16.0) in devicetree and gets rid of the I2C tuning parameters for I2C0. BUG=b:115600671 Change-Id: Ib799eae05b667cee2272bbd37f0ca44b7cec66cd Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/28931 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-10-01mb/google/octopus: Operate touchpad I2C CLK in specChris Zhou
Need to tune I2C bus 6 clock frequency under the 400K Hz Bug=b:115600671 TEST=flash coreboot to the DUT and measure I2C bus 6 clock frequency whether arrive to 398.07K Hz Change-Id: I5cc1f67f0db0553cb8424f81408ed4686cddb2fb Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/28760 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-09-28src/*: normalize Google copyright headersPatrick Georgi
As per internal discussion, there's no "ChromiumOS Authors" that's meaningful outside the Chromium OS project, so change everything to the contemporary "Google LLC." While at it, also ensure consistency in the LLC variants (exactly one trailing period). "Google Inc" does not need to be touched, so leave them alone. Change-Id: Ia0780e31cdab879d2aaef62a2f0403e3db0a4ac8 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/28756 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Joel Kitching <kitching@google.com>
2018-09-21mb/google/octopus/variants/fleex: Update DPTF parametersSumeet Pawnikar
Update Power Limit1 and Power Limit2 values along with stepsize. Correct the charger effect for Temperature sensor2. BUG=b:112448519 BRANCH=None TEST=Build coreboot for Octopus board. Change-Id: I01e0a94fe694537d9eebe3b92c11d0c83137d716 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/28530 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-09-06mb/google/octopus: Configure H1 interrupt pad using Rx level configFurquan Shaikh
This change configures GPIO_63 (which is used for H1 interrupts) as Rx Level. This ensures that the signal gets passed on to the next logic state as is and the APIC entry can be configured to trigger interrupt on level or edge as per the kernel driver expectation. TEST=Verified that no H1 interrupt timeouts are seen with 100 iterations of warm and 100 iterations of cold reboot. Change-Id: I7aac30300a4251d9b40276dcca7ebc6a6d814c40 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/28507 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-08-30mb/google/octopus: Add missing IOstandy settings.Shamile Khan
Also removed internal pull ups for CX_PREQ_L and CX_PREQ_L signals as they have external pull ups. BUG=b:110654510 TEST=On Yorp Proto 2, flashed image and verified that it boots to OS. Checked Wake-on-Wifi works with both cnvi and pcie modules. Also executed a few suspend resume cycles. Change-Id: I0a76cd2a1481c828fc092aaf7e870a411624879c Signed-off-by: Shamile Khan <shamile.khan@intel.com> Reviewed-on: https://review.coreboot.org/28328 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-08-20mb/google/octopus/variants/fleex: Increase weida touchscreen reset delayCrystal Lin
Weida touchscreen controller needs 130 ms delay after reset BUG=b:111102092 BRANCH=master TEST=Verify touchscreen on fleex works with this change Change-Id: Ia86c3acf3c0e09ca05cc1681113672b546f830a0 Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/28115 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-08-13mb/google/octopus/variants/fleex: Set up DPTF tableJohn Su
Follow thermal table (b:112274477 comment#1) for first tunning. BUG=b:112274477 TEST=Match the result from DPTF UI. Change-Id: I63b2e50a4f6fc5453e6564e277600498ac0e6244 Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/27969 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
2018-08-12mb/google/octopus/var/fleex: Update GPIO config for fleex bid >= 1Furquan Shaikh
This change updates GPIO configuration for fleex boards with id >= 1 This follows the same model as phaser: a. Dynamically update touchscreen power enable GPIO in devicetree. b. Provide default and bid0 tables for GPIO configuration in ramstage. c. Configure WLAN enable GPIO differently in bootblock based on boardid. d. Disable unused I2C devices in devicetree. BUG=b:112458032 TEST=No errors observed on boot-up on fleex. Change-Id: Ib4c449168b08e2393e2395d6b49469be5599c2ce Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/28015 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-08-06mb/google/octopus/variants/fleex: Enable Weida touchscreen deviceCrystal Lin
This change adds ACPI properties for WDT8752A device. BUG=b:111402335, b:111102092 BRANCH=master TEST=Verify touchscreen on fleex works with this change Change-Id: Id186d5b87343007ae7e631d5d27464ee27e5b27d Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/27800 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-06-25mb/google/octopus: Use the newly added override devicetree featureFurquan Shaikh
Now that sconfig is able to support variant-specific override trees, this change updates octopus boards to use this feature. Following devices are moved from baseboard devicetree to variant specific devicetree: 1. Touchscreen 2. Trackpad 3. Digitizer 4. Audio codec BUG=b:80081934 TEST=Verified that the right devices show up in static.c for each variant. Change-Id: I8df0cdf4dbcd7613aa4ef4042c272eca2915da9e Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/27219 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-06-18mb/google/octopus: Create fleex variantJustin TerAvest
This creates a fleex variant for octopus. Nothing is set in the variant files here; everything is picked up from baseboard. BUG=b:110085182 TEST=None Change-Id: Ia8b8bb757f67bea997b7f43489c38cac62f7682d Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/27105 Reviewed-by: Jett Rink <jettrink@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-19 07:35:17 +0000