Age | Commit message (Collapse) | Author |
|
Change-Id: I960870fabde1dacfe52a8a35c253b0bd097d3e10
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Ic334816712370da63471135da8dd598ab02d54ef
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
variant_smi_sleep is called in smm stage so we need to add
variant.c into smm stage. Otherwise it will call the dummy one.
BUG=b:168075958
BRANCH=octopus
TEST=build image passed.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I41df1a30b119ab3e04f9ae01955b6044f137527f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46847
Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
LTE module Fibocom L850-GL is lost after idle overnight,
with this workaround, host will not initiate U3 wakeup
at the same time with device, which will avoid the race condition.
If this option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR +
offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0.
BUG=b:169645448
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3a04320b0e2441dce540a5afdc461f12de45c41b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
|
|
Add goodix touch pad as below:
HWID : GXTP7288
CID : PNP0C50
I2C address : 0x2C
I2C speed : 400Khz
HID Descriptor Address : 0x20
BUG=b:171351666
BRANCH=octopus
TEST=build image and verify goodix touch pad working.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Idb4f8d3aff09712dcc98c8ae0c9ae30dc4049e29
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46614
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New SKU ID 5 is used for LTE touch SKU. This patch does LTE power off
for LTE sku and only use Wifi SAR table for non-LTE sku.
BUG=b:168001586
BRANCH=octopus
TEST=Check no SAR table can be loaded with sku id 4 and 5.
Change-Id: Ic0405d3e52aa813bbb1f350966a9e2825e595ce4
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46643
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch makes Fleex EC wake up AP from s0ix when the state of
charge drops to 5%.
Demonstrated as follows:
1. Boot Fleex.
2. Run powerd_dbus_suspend.
3. On EC, run battfake 5.
4. System resumes.
BUG=b:163721887
BRANCH=Octopus
TEST=Verified on Fleex:
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: I4a998ad0aef5a7cfc6fd18995bde5571e6127e77
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Only do LTE power off for LTE sku in order to save extra 130ms delay
for non-LTE sku.
BUG=b:168075958
BRANCH=octopus
TEST=build image and verify on the DUT with LTE DB.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If983185ff2f09fb1b2553c6ff1a1473d3254de4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
|
|
Use Wifi SAR table for non-LTE sku only.
BUG=b:169115341
BRANCH=octopus
TEST=Check no SAR table can be loaded with sku id 4.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I086fa14a9f23e4a0fc0ef8085040219c932dbf17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45640
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All octopus board share the same power off sequence.
Move to smihandler.c instead variant.c.
BUG=b:168075958
BRANCH=octopus
TEST=build image and verify on the DUT with LTE DB.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I2be5a656fb42fff99c56d21aaa73ed9140caad37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45436
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIOs related to power sequence are
GPIO_67 - EN_PP3300
GPIO_117 - FULL_CARD_POWER_ON_OFF
GPIO_161 - PLT_RST_LTE_L
1. Power on: GPIO_67 -> 0ms -> GPIO_117 -> 30ms -> GPIO_161
2. Power off: GPIO_161 -> 30ms -> GPIO_117 -> 100ms -> GPIO_67
3. Power reset:
- keep GPIO_67 and GPIO_117 high and
- pull down GPIO_161 for 30ms then release it.
BUG=b:168075958
BRANCH=octopus
TEST=build image and verify on the DUT with LTE DB.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I9b56ef8ff346c1d4edd5aad04d4a7396c4702ffc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45193
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:167297664
BRANCH=octopus
TEST=build fleex, and check touchscreen can work
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I910681c258ff5487830e795a8bd08c66be69b1d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44980
Reviewed-by: Justin TerAvest <teravest@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I8076155330100982de82d410b6579ac99ed89e7b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40187
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I09cc279b1f75952bb397de2c3f2b299255163685
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Update GPIO_138 and GPIO_139 setting to fix EMR function.
BUG=b:141729962,b:141281846
BRANCH=octopus
TEST=verify EMR function in Grob360S.
Change-Id: I28cef592374fb4aeee2f3d3010cc0e237d62a2fd
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
After adjustment on Grob360S
I2C0 CLK: 389.9 KHz
BUG=b:141729962
BRANCH=master
TEST=emerge-octopus coreboot chromeos-bootimage
measure by scope with Grob360S.
Change-Id: I6a30257b7978cc8899a55f9fd6ffffe01cb2a851
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Enable I2C0 in fleex then verify EMR function successfully
BUG=b:135968368
BRANCH=octopus
TEST=EMR function working normally with I2C0 in Grob360S.
Change-Id: I784ff32418bc839bcec14fbfd7236f708828690e
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable EMR Pen Stylus function for Grob360S
BUG=b:135968368
BRANCH=octopus
TEST=EMR function working normally with HW reworked Fleex.
Change-Id: Ia220dc0d3051b79b110b4df66df108f701776478
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33802
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set default configuration to low for gpio_178, and can remove the
override setting for bobba/bloog/fleex/meep/phaser.
For ampton, Change-Id I64a67f73564188ad0548a1a770169ef2bca47453 (
mb/google/ampton: Fix polarity of EN_PP3300_WLAN_L signal.)
modified the pin setting.
TEST=verified that boot into OS on meep board.
suspend/resume, reboot, and no failure found.
Change-Id: I7668ff4817edfca5c6cea63db779fcea21c7af92
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32247
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These pins should not have pull downs configured in standby state as that
can cause contention on the termination circuitry and lead to incorrect
behavior as per Doc# 572688 Gemini Lake Processor GPIOTermination
Configuration.
BUG=b:79982669
TEST=Checked that code compiles with changes.
Change-Id: If3cadc000ec6fc56019ee3f57e556dc819d5e0a5
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/c/30823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Some usb devices exhibits signal loss which causes xHCI entering
compliance mode. The resolution is to disable xHCI compliance mode.
BRANCH=octopus
BUG=b:120009029
TEST=Verified usb operation successfully.
Change-Id: Ic7fa08c894397598dee3c4ff9a764e43383a0627
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable the EC_AP_INT_ODL interrupt on GPIO_134 for all octopus boards
that support it. Also removing unnecessary IO standby support since we
don't use this pin to wake up the SoC.
BRANCH=octopus
BUG=b:122552125,b:120679547
TEST=CTS tests with changes
Change-Id: I018864ae5fa400372b5b443e49828e8202b9aa4d
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30788
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New emmc DLL values for Fleex.
BUG=b:120561055
TEST=Boot to OS, chromeos-install, mmc_test
Change-Id: Id0022e9d0f0a7802113bbf193decff3c8aaa04f8
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30226
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 969ed357f823659a6861a2ca38f3ad9d7b58f949
Reason for revert:
According to partner issue b:112448519 comment#80, it impacts
skin temperature specifications.
Change-Id: I7603c3816f34adebc1f67eff6fad214557544022
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Update dptf settings for Charger throttling. Also, update Power
Limit1 minimum value setting from 4.5W to 3W.
BUG=b:112448519
BRANCH=octopus
TEST=Built and tested on Fleex system
Change-Id: I8c2a796ff28254ebef28ed5745b344f925d6e649
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This change gets rid of bid0_override_table as part of clean up effort
to deprecate bid0. Additionally, it updates the touchscreen enable
GPIO in overridetree and gets rid of variant.c to update enable gpio at
runtime.
BUG=b:119885949
Change-Id: If14abb324d9422720ca4d0f0859e092319d454ee
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/29785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This change updates the configuration of GPIO_178 to be active low as
per latest revision on different octopus variants. This effectively:
1. Gets rid of early_gpio_table in different variants -- phaser, meep,
fleex, bobba.
2. Deprecates board id < 2 for bobba, board id < 1 for fleex and
phaser.
3. Adds special early_gpio_table in yorp which has GPIO_178 as an
active high signal.
BUG=b:119885949
Change-Id: I024199a8f1f96db57f8fa60c4d265789cd3a0493
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/29784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Change tcc offset from 0 to 10 for fleex.
Refer to b:117789732#1
BUG=b:117789732
TEST=Match the result from TAT UI
Change-Id: I481526ab10a16a33fe0cf9528b52b8524e012451
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
1. Update PSV values for cpu and sensers.
2. Change PL1 min value from 3w to 4.5w.
3. Change TSR2 TRT source from charger to CPU.
Refer to 112448519#comment31.
BUG=b:112448519
TEST=Build coreboot for Octopus board
Change-Id: I7c7df0f54374fdaa4cf57d5c255d841d7db38cfc
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This change uses the newly added macros for configuring the same GPI
pad(GPIO_135) for IRQ (normal interrupt operations) and
wake (interrupt for waking from S3/S0ix) for the trackpad device. The
other pad GPIO_142 is now configured as not connected.
BUG=b:117553222
TEST=Verified that yorp and bobba wake from S3 and S0ix using
trackpad.
Change-Id: I2b704f1be493141629c647b79723b0025b0f7dd6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29189
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fleex does not have any device on I2C0 and hence this change disables
I2C0 device (16.0) in devicetree and gets rid of the I2C tuning
parameters for I2C0.
BUG=b:115600671
Change-Id: Ib799eae05b667cee2272bbd37f0ca44b7cec66cd
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Need to tune I2C bus 6 clock frequency under the 400K Hz
Bug=b:115600671
TEST=flash coreboot to the DUT and measure I2C bus 6 clock
frequency whether arrive to 398.07K Hz
Change-Id: I5cc1f67f0db0553cb8424f81408ed4686cddb2fb
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per internal discussion, there's no "ChromiumOS Authors" that's
meaningful outside the Chromium OS project, so change everything to the
contemporary "Google LLC."
While at it, also ensure consistency in the LLC variants (exactly one
trailing period).
"Google Inc" does not need to be touched, so leave them alone.
Change-Id: Ia0780e31cdab879d2aaef62a2f0403e3db0a4ac8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
Update Power Limit1 and Power Limit2 values along with stepsize.
Correct the charger effect for Temperature sensor2.
BUG=b:112448519
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: I01e0a94fe694537d9eebe3b92c11d0c83137d716
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28530
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change configures GPIO_63 (which is used for H1 interrupts) as Rx
Level. This ensures that the signal gets passed on to the next logic
state as is and the APIC entry can be configured to trigger interrupt
on level or edge as per the kernel driver expectation.
TEST=Verified that no H1 interrupt timeouts are seen with 100
iterations of warm and 100 iterations of cold reboot.
Change-Id: I7aac30300a4251d9b40276dcca7ebc6a6d814c40
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Also removed internal pull ups for CX_PREQ_L and
CX_PREQ_L signals as they have external pull ups.
BUG=b:110654510
TEST=On Yorp Proto 2, flashed image and verified that it boots to OS.
Checked Wake-on-Wifi works with both cnvi and pcie modules.
Also executed a few suspend resume cycles.
Change-Id: I0a76cd2a1481c828fc092aaf7e870a411624879c
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/28328
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Weida touchscreen controller needs 130 ms delay after reset
BUG=b:111102092
BRANCH=master
TEST=Verify touchscreen on fleex works with this change
Change-Id: Ia86c3acf3c0e09ca05cc1681113672b546f830a0
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Follow thermal table (b:112274477 comment#1) for first tunning.
BUG=b:112274477
TEST=Match the result from DPTF UI.
Change-Id: I63b2e50a4f6fc5453e6564e277600498ac0e6244
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This change updates GPIO configuration for fleex boards with id >= 1
This follows the same model as phaser:
a. Dynamically update touchscreen power enable GPIO in devicetree.
b. Provide default and bid0 tables for GPIO configuration in ramstage.
c. Configure WLAN enable GPIO differently in bootblock based on
boardid.
d. Disable unused I2C devices in devicetree.
BUG=b:112458032
TEST=No errors observed on boot-up on fleex.
Change-Id: Ib4c449168b08e2393e2395d6b49469be5599c2ce
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change adds ACPI properties for WDT8752A device.
BUG=b:111402335, b:111102092
BRANCH=master
TEST=Verify touchscreen on fleex works with this change
Change-Id: Id186d5b87343007ae7e631d5d27464ee27e5b27d
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Now that sconfig is able to support variant-specific override trees,
this change updates octopus boards to use this feature. Following
devices are moved from baseboard devicetree to variant specific
devicetree:
1. Touchscreen
2. Trackpad
3. Digitizer
4. Audio codec
BUG=b:80081934
TEST=Verified that the right devices show up in static.c for each
variant.
Change-Id: I8df0cdf4dbcd7613aa4ef4042c272eca2915da9e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27219
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This creates a fleex variant for octopus. Nothing is set in the variant
files here; everything is picked up from baseboard.
BUG=b:110085182
TEST=None
Change-Id: Ia8b8bb757f67bea997b7f43489c38cac62f7682d
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27105
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|