| Age | Commit message (Collapse) | Author |
|---|
|
Use 2T memory timings on Liara for all board IDs.
BUG=b:116082728
TEST=Build & boot on Liara
Change-Id: I5814e63db35cf7761f4f20792b0f3cf4120a1b60
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/30285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
Commit d80884ea5a ("mb/google/kahlee: Disable IOMMU") disabled the IOMMU
in all kahlee variants, but omitted the explaining comment only in
liara's devicetree.cb. Copy this comment to liara.
Change-Id: I564013a16217445003467e2a0579abd50597b205
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Using ${...} in some places is slightly confusing.
Fixes: 395cbb4f97 ("mb/*/*/Kconfig: Use CONFIG_VARIANT_DIR for devicetree")
Change-Id: Id0856a10d92786a41d45ca697945699f6f4c1f4c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
file Module Part Number
Correct Ram_ID=0b0000 SPD Module Part Number mismatch last alphabet 'C'
to "H5AN8G6NAFR-UHC".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I4f4b83589ad6b53c0a24f2637f0fe8b92a1168e3
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
file Module Part Number
Correct to add Ram_ID=0b0001 SPD Module Part Number mismatch last alphabet 'C'
to "H5ANAG6NAMR-UHC".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I4d320b2e10c4865456a9a9ccb400db5dd9256b3e
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30177
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Part Number
Correct Ram_ID=0b0011 SPD Module Part Number to "MT40A1G16KNR-075:E" from
"4ATS1G64HZ-2G6E1".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I9d582b3753de9a48865eb6eca7e4fbdb31b799ff
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Number
Correct Ram_ID=0b0000 SPD Module Part Number to "H5AN8G6NAFR-UH" from
"HMA851S6AFR6N-UH".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I1f6e885638589a35334a9a8f905af4877c5d1f91
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Part Number
Correct Ram_ID=0b0010 SPD Module Part Number to "MT40A512M16JY-083E:B"
from "4ATF51264HZ-2G3B2".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I6847a55968260cdbc1588ddeb8d23c515ad87920
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
A new liara specific VBIOS updating eDP power sequence is available now,
Change Kconfig to use it if board is google liara.
BUG=b:120534087
TEST=Build liara, booted, tested eDP test compliance.
Change-Id: I444cfa0bd755480e006f11c0d692b25b96129c29
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/30090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Move the backlight initialization from bootblock to romstage
BUG=b:120436919
TEST=Careena backlight is enabled
Change-Id: Ia4993b993d37afaf9e23d6f3316ba91053732f1d
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
According to aleena thermal testing to set STAPM values.
skin scalar for 80%.
time constant for 2500s.
power limit for 7.8w.
BUG=b:72979852
TEST=test build for thermal check.
Change-Id: I09f1c1052dd317969546ac7d2bbde14cc563c160
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Correct Ram_ID=0b0001 SPD Module Part Number to "H5ANAG6NAMR-UH" from "HMAA51S6AMR6N-UH".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I59d920498ff6b73e9e7b2887771ad6bc6c6c0b66
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The aleena board uses a display that's not compatible with current VBIOS.
A VBIOS specific for aleena has been merged into blobs, so modify Kconfig
so that it loads the new VBIOS when building aleena, but load original VBIOS
for all other boards under kahlee folder.
BUG=b:112618193
TEST=Build each board under kahlee, one at a time. After each build, opened
build/config.h and searched VGA_BIOS_FILE to verify that the string only
changed for aleena, all other boards remained with original string.
Change-Id: Iccd0853692680908d951edd142a2d8e13a561391
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change the board id detection to support rev5, since the 2T mode still
needed in DVT build.
BUG=b:116082728
TEST=verify by ODM.
Change-Id: Ibb4cc1fd2bb54984cb7a8856ed7b9f49b78eddce
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Field 'OEMID' & "OEM Table ID" are related to DSDT table
not to mainboard.
So use macro to set them respectvely to "COREv4" and
"COREBOOT".
Change-Id: I060e07a730e721df4a86128ee89bfe168c69f31e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Guckian
|
|
We need to default this to low so the speakers don't activate in S3.
BUG=b:118248953
TEST=Used a scope to look at the line and made sure depthcharge still
beeps.
Change-Id: I70d2f4a3261d212b62e784fa7414e45b1d575612
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/29783
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds ACPI properties for WDT8752A device.
BUG=b:117174180
BRANCH=master
TEST=Verify touchscreen on delan works with this change
Change-Id: Id1484a482de6282c97f3aac329f217bbcb7dbd18
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
Correct SPD Module Part Number to "K4A8G165WC-BCTD" from "M471A5244CB0-CTD".
BUG=b:119400832
BRANCH=master
TEST=emerge-grunt coreboot chromeos-bootimage
mosys memory spd print all
0 | DDR4 | SO-DIMM
0 | 1-78: Samsung | 00000000 | K4A8G165WC-BCTD
0 | 4096 | 1 | 64
0 | DDR4-1333, DDR4-1600, DDR4-2400
Change-Id: I29505d3eece2283579499a0afc424c4a28017fa5
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/29557
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After adjustment on aleena EVT
Audio: 390.0 KHz
H1: 390.0 KHz
TP: 399.8 KHz
TS: 399.8 kHz
BUG=b:116306959
BRANCH=master
TEST=emerge-grunt coreboot, scope measuring.
Change-Id: I6f621508ce2dbb1b9dcdf529ac35afc80d485f53
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I17c4fc4e3e2eeef7c720c6a020b37d8f7a0f57a4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add 20ms adjust timing for edp panel in devicetree.
BUG=b:118011567
TEST=verify panel sequences by ODM.
Change-Id: Iab46f6fc653047a1ec6e8528eefa0999d7019690
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29473
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Add two parameters for panel initialization timing.
> lvds_poseq_varybl_to_blon
> lvds_poseq_blon_to_varybl
2. The BL_PWM is controlled by APU_EDP_BKLTEN_L/APU_DP_VARY_BL/
EDP_BKLTEN_L, so move APU_EDP_BKLTEN_L to early init stage,
and be enabled depends on SKU, thus we can control the delay
time by config APU_DP_VARY_BL.
BUG=b:118011567
TEST=emerge-grunt coreboot.
Change-Id: Ib20c48813b208d697b950b2f02a70a690e483fdb
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ib3aafcc586b1631a75f214cfd19706108ad8ca93
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29285
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Unfortunately Stoney has an issue where enabling the IOMMU causes
a 10%-50% decrease in the integrated graphics performance. It is
also disabled by default on other stoney platforms.
BUG=b:118612241
TEST=Verify that IOMMU is disabled.
Change-Id: Ia396c7227cb21461ec8afbdf746721d4fb28083d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/29342
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In function write_pirq_routing_table(), the function name is used in a print
string. Use __func__ instead.
BUG=b:117642170
TEST=Build grunt.
Change-Id: Ibf8673c5b2cda1105aae1edb46f6589d55208c50
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Liara auto restart issue is caused by memory access error and consequent
kernel panic. To solve this issue, revert the CL:1243666 (Disable
NbP-state on Liara) and use 2T mode instead.
BUG=b:116082728
TEST=verify the 2T mode is enabled/boot into ChromeOS and no auto restart/run
memtester passed 10 cycle.
Change-Id: I3a96276d88ffb70530d72b15c07b59a01cc6209a
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
The file soc/amd/stoneyridge/acpi/smbus.asl has 0 bytes (no content). Remove
the include of this file.
BUG=b:117814641
TEST=Build grunt and gardenia.
Change-Id: I0c48167195a9708afc255490bb1996b6dfc7bdfb
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29178
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
I didn't change the offsets of all the other regions because I didn't
want to cause all dogfood devices to lose their corp enrollment.
BUG=b:117797131, b:117798830
BRANCH=none
TEST=Ran autotest and made sure the tests were skipped
/tmp/test_that_results_2OZ90v/results-1-firmware_CorruptRecoveryCache [ PASSED ]
/tmp/test_that_results_2OZ90v/results-1-firmware_CorruptRecoveryCache TEST_NA: No RECOVERY_MRC_CACHE was found on DUT.
/tmp/test_that_results_2OZ90v/results-1-firmware_CorruptRecoveryCache/firmware_CorruptRecoveryCache.normal [ PASSED ]
/tmp/test_that_results_2OZ90v/results-1-firmware_CorruptRecoveryCache/firmware_CorruptRecoveryCache.normal TEST_NA: No RECOVERY_MRC_CACHE was found on DUT.
Change-Id: I5cdbf4139dde80fe6e9d0045139a97841b03bc42
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/29171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Make the field names of the MISCx00 GPPClkCntrl more manageable by
shortening their names. Make the definitions look more like the
rest of the header file.
Change-Id: I515cd664808e38851a7dbdba899df4fb9bbbcde6
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
STAPM devicetree registers do not indicate the unit, which causes confusion.
More importantly, the time was assumed to be in seconds when it's actually
milliseconds. This caused early STAPM configurations to fail.
BUG=b:117590953
TEST=Build grunt
Change-Id: I2a7e3d43601992d1f7b02456913c763d940fe9ee
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29035
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With correct stapm values audio issue is not observed with
PsPPBalanceLow (Gen1 speed).
BUG=b:117569918
TEST=audio playback multiple times
Change-Id: Iaeae52b262b12622a6753432e3fc40bf5f0fd8e0
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/29028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
stapm_time passed to smu via agesa is in msec. With earlier value
smu was getting stapm_time as 2.5 sec instead of 2500 sec and thus
causing issue in S3, and audio in PsppBalanceLow state.
BUG=b:117569918, b:117252463
TEST=
1.) audio works with PsppBalanceLow
2.) S3 cycles
Change-Id: I673e7e673d042918dff47141f37bbca354f5c45c
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/29027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Use the new I2C slave reset function and reset all slaves connected to all
4 I2C. Do this in all boards.
BUG=b:114479395
TEST=Added debug code. Build and boot grunt. Examined output, confirmed
GPIO pins changing as required. Removed debug code.
Change-Id: Ia78ee5d5319d3c1a7daa9c56c81d435999b3a359
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28575
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:117173908
TEST=Build delan
Change-Id: If149b8c43ff16637c38d5320eb606bb72d62e953
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
After adjustment on Liara EVT
H1: 392.03 KHz
TP: 397.87 KHz
TS: 397.71 KHz
BUG=b:116309237
BRANCH=master
TEST=emerge-grunt coreboot chromeos-bootimage
measure by scope
Change-Id: Ib5d7ce09ac58f33ee826d7541e1a0d14a03add9a
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Setting default PSPP setting to BalancedLow was causing audio
playback issue in most of the units. With BalancedLow either there
was no sound or noise on playback.
Switching to BalancedHigh as default option.
BUG=b:116553085, b:112020107
TEST=Test playback and hear proper audio.
Change-Id: Ibf64d7b8e58e60ce931ddc85f11b135708cdb1ee
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/28967
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Its spreading copies got out of sync. And as it is not a standard header
but used in commonlib code, it belongs into commonlib. While we are at
it, always include it via GCC's `-include` switch.
Some Windows and BSD quirk handling went into the util copies. We always
guard from redefinitions now to prevent further issues.
Change-Id: I850414e6db1d799dce71ff2dc044e6a000ad2552
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Setting the stapm parameters is causing S3 resume failures and
performance issues. Removing these settings until more testing is
done and the issues are solved.
BUG=b:117252463, b:116870267
TEST=boot grunt
Change-Id: I2299ab81fcc2af0529bfac3be562b05116c64a49
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
In CBFS layout:
oem.bin size is 10 bytes.
In cbfs_boot_load_file, buffer size will need to be larger
than decompressed_size, otherwise CBFS data can not be
extracted into buffer.
Then we need to check buffer whether it's empty string separately.
BUG=b:79874904
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I4f1bbb690ecca515ac920f5058ee19b5bfd8fa5e
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
After adjustment on Careena
Audio: 402.805 kHz -> 396.8 kHz
TP: 406.1 kHz -> 399.5 kHz
BUG=b:110984023
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: Ia3eb91ca3772d5f122498e3989ec03838fce06a5
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable the IOMMU device on all kahlee based mainboards.
BUG=b:116196614
TEST=Check dmesg for AMD-Vi messages.
Change-Id: I18b9ba1a970c6973226e736d72f82fd53010f31c
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/28754
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FCH ASL is now capable of controlling the D-states of most AOAC
devices, as well as properly reinitializing the xHCI firmware on a
resume. Call the FPTS and FWAK methods.
BUG=b:77602074
TEST=On Grunt, go to S3 and wake with a USB keyboard
Change-Id: I4df8523569dc3dfbd87f79e780c18d39f0d9a37f
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28773
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per internal discussion, there's no "ChromiumOS Authors" that's
meaningful outside the Chromium OS project, so change everything to the
contemporary "Google LLC."
While at it, also ensure consistency in the LLC variants (exactly one
trailing period).
"Google Inc" does not need to be touched, so leave them alone.
Change-Id: Ia0780e31cdab879d2aaef62a2f0403e3db0a4ac8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
Since each variant has a separate build, we don't need to support
multiple manufacturers in a single file.
BUG=b:79874904
TEST=Build, boot, see updated mainboard manufacturer
Change-Id: I0ccf207ba8d5e5200aa4b19c46784bbda82f7b6e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/28729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
To disable NB-Pstate, the system wouldn't auto restart on EVT board when idling.
BUG=b:116082728
Change-Id: Iec4f0355cb6eb1c2b0372e3d131cc5e6ba36635e
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
STAPM programming was created inside function OemCustomizeInitEarly().
It should be SOC specific, and called by agesawrapper just before the
call to OemCustomizeInitEarly().
BUG=b:116196626
TEST=build and boot grunt
Change-Id: I8a2e51abda11a9d60a9057b38f2a484e1c8c9047
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28705
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Grunt variants need a way to customize the mainboard vendor based on the
platform. For future boards, this can probably be done via CBI, but
grunt doesn't support that method.
BUG=b:79874904
TEST=Build, boot, see updated mainboard vendor
Change-Id: I997dc39c7f36f70cf4320ef335831245889eb475
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/28651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@google.com>
|
|
AMD has tested careena, and for the time being is recommending a scalar
of 68%, power limit of 7.8 W and time constant of 2500. Using new STAPM
configuration code, set the desired values.
BUG=b:111561217
TEST=none, code was tested with grunt.
Change-Id: I42671ab0e66b21dc4f8c8c326c1fa33328b1390e
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
While the pin was set to a pull-down, with the external pull-up, this
wasn't enough to keep the pin low. Set to output low to drive to 0V.
TEST=Boot grunt, verify EMMC_BRIDGE_RST is 0V.
BUG=b:115661061
Change-Id: Ife014b8a879274df5d892c1de386976808de1df0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
These values override the default subsystem IDs, and aren't needed.
BUG=b:113253260
TEST=Boot grunt
Change-Id: I3c56534b094ede8d8200b72f4433a891d0094064
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/28652
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Default STAPM percentage causes a lot of thermal throttling on grunt.
AMD experimented with 80%, it works for grunt. This is initial code to
provide easy change path for other grunt based platforms.
BUG=b:111608748
TEST=build and boot grunt.
Change-Id: I22863f6ed76152bf872fce3e275f8a7fd8077504
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Only for those that are x86 and also have a RW_LEGACY region.
The assumption is that all devices touched have 64k block sizes when
choosing size and alignment of the region.
Change-Id: I12addb137604f003d1296f34f555dae219330b18
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
AMD chips don't hold off a reset to the end of I2C transitions, so
devices on the i2c bus can be left in a bad state. To avoid this,
make sure the trackpad and touchscreen chips get disabled
during boot.
BUG=b:114411165
TEST=build, reboot watch trackpad enable go low
Change-Id: Ie50f4a102249df79517da571a6e768dba804cd57
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28538
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set GPIO135 high to enable audio through the BCLK buffer.
BUG=b:113559558
TEST=None
BRANCH=grunt
Change-Id: I1dcecf5960d3c91e0c2165e7f8856ff423c06e8c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28482
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Synaptics touchpad device for liara
BUG=b:113309346
BRANCH=master
TEST=Verify touchpad on liara works with this change
Change-Id: Icdafe34a00fd55d5338fa07ffa304e48e7b85e7b
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
After adjustment on Liara Proto
Audio: 399.2 KHz
H1: 398.3 KHz
TP: 399.0 KHz
BUG=b:113319200
BRANCH=master
TEST=emerge-grunt coreboot chromeos-bootimage
measure by scope
Change-Id: Ibba8c823ed8451a804cf731d49e7568a94ac7c6b
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Grunt takes a few seconds to update the EC, so display a notification
screen while that's happening.
BUG=b:113286040
TEST=Boot Grunt with old EC firmware, see update screen
Change-Id: I95fc4d3430bac66c09f57a4d34abde08752e5f0e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Bayhub eMMC controller default runs SD base 50MHz at the first power on.
After boot into OS, mmc kernel driver will config controller to HS200/208MHz
and send MMC CMD21 (tuning block).
But Bayhub PCR register 0x3E4[22] (eMMC MODE select) is not clear
after system warm reset.
So eMMC will still run 208Mhz but there is no block tuning cmd in depthcharge.
It will cause two Sandisk eMMC (SDINBDA4-64G-V/SDINBDA4-32G-V) to fail to
load kernel and trap in 0x5B error (No bootable kernel found on disk).
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: Ic080682e67323577c7f0ba4ed08f8adafca620cc
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This commit fixes the values and thus fixes the issue of
audio device not getting detected on random reboots.
Change-Id: I34a4f62815d192005c3324d4f71b0aba377fe738
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/28280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
After adjustment on Careena EVT
TP: 400.0 KHz
TS: 396.8 KHz
H1: 396.8 KHz
BUG=b:112663934,b:112664258
BRANCH=master
TEST=emerge-grunt coreboot
measure by scope
Change-Id: I9eeaf9290d95969a283f14618878e28faf0ea46f
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28119
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix the following failure from FWTS:
FAILED [LOW] AMLAsmASL_MSG_SERIALIZED_REQUIRED: Test 1, Assembler remark in line
131
Line | AML source
--------------------------------------------------------------------------------
00128| }
00129| }
00130| })
00131| Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
| ^
| Remark 2120: Control Method should be made Serialized (due to creation of named objects within)
00132| {
00133| Name (RBUF, ResourceTemplate ()
00134| {
================================================================================
ADVICE: (for Remark #2120, ASL_MSG_SERIALIZED_REQUIRED): A named object is
created inside a non-serialized method - this method should be serialized. It is
possible that one thread enters the method and blocks and then a second thread
also executes the method, ending up in two attempts to create the object and
causing a failure.
BUG=b:112476331
TEST= Run FWTS.
Change-Id: I6f4f6e7e94b01f673afc97d9415481ee63e406e3
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28122
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
change I2C irq to EDGE trigger
BUG=b:112616824
BRANCH=master
TEST=emerge-grunt coreboot
Raydium TS is working.
Change-Id: I86ec32bb3f2626e65d76c3259e3c4244a970e5de
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Side effect was observed that after override BayHub EMMC
driving strength to the max, EMMC CLK will be reduced to
51.x Mhz from 200 Mhz.
This will cause OS installation fail on Samsung EMMC sku.
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I848ab0cae474b15fbc4264c8ade63d5c6b4e489d
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I189c981f3334836ab24bbc74491e9b58a2d403a4
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/27921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Careena EVT SanDisk EMMC sku has high fail rate of 0x5B reboot failure.
It'll need to increase 1.8V EMMC CLK/CMD, Data driving strength for
this issue.
CLK[6:4]
CMD,DATA[3:1]
original register value: 0x6B
enhanced: 0x7F
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I3db38ff12c566c258895c6643008a0472ca528bb
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27816
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This configures the ACPI FADT perferred power management profile to
PM_MOBILE instead of PM_DESKTOP.
I'm not sure what impact this actually has. I just noticed the other
boards have it set.
BUG=b:110971913
TEST=Made sure SYSTEM_TYPE_LAPTOP shows up in coreboot.config
Change-Id: Iea1b8359b80d167e69745358f543f025713294ba
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add default PSPP AGESA setting for Kahlee/Grunt mainboards.
BUG=b:112020107
TEST= build test
Change-Id: I8a8605402379de88a04f3a16553c308513fa1531
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Now that an updated bootloader with important fixes is available at coreboot
repository, all stoneyridge boards should use it. Move the selection of
SOC_AMD_PSP_SELECTABLE_SMU_FW from mb/google/kahlee to soc/amd/stoneyridge.
BUG=b:111428800
TEST=Build and boot grunt.
Change-Id: Idf8e348efbc85569aa1163125f412c5242c46eb4
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27844
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kahlee based boards don't use SATA, so disable SATA on all boards to save
power.
BUG=b:112139043
TEST=Build and boot grunt, checked the absence of SATA PCI.
Change-Id: I6a12c03a5a95b1c8b40609a3fe656df92548b80b
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The careena board requires a different setting within VBIOS in order to
pass the eDP eye diagram test. Update all kahlee boards to use the new vBIOS.
CQ-DEPEND=CL:1153080
BUG=b:111673328
TEST=Verify, via SOME unspecified method, that the new vBIOS is built into
the Grunt/Careena ROM files.
Change-Id: I268cd3dbce6ba1f7bd781d768f470463846a4e10
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27643
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The careena board needs different video settings to pass eye diagram test,
which does not affect negatively the grunt board. In preparation for new
VBIOS, AGESA environment needs eDP high vdiff enabled.
BUG=b:111673328
TEST=Add debug code to AGESA to display set eDP. Build AGESA. Build and
boot grunt. Add new code to grunt, build and boot, verify eDP changed.
Change-Id: I3e6b409699e8192eb39cc189628ff95b9f985e54
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
All of the other SPDs are padded with spaces to make them use the full
size of the serial number field. The hynix-H5AN8G6NCJR-VKC SPD was not,
and that seems to be causing problems with some tools.
BUG=b:111903749
TEST=Mosys correctly identifies memory on board using that SPD.
Change-Id: I0e831873acab2f6fc7d76e85647198d3b7af4b12
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
|
|
Fix Micron MT40A512M16LY-075:E DRAM SPD CRC error in AGESA MemSPDChecking:
ERROR Event: 04011200 Data: 0, 0, 0, 0
BUG=b:111901461
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I85c82fd9294f9146fc23e649436cbcc337c4c961
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27657
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per the ACPI specification, there are two types of power button
devices:
1. Fixed hardware power button
2. Generic hardware power button
Fixed hardware power button is added by the OSPM if POWER_BUTTON flag
is not set in FADT by the BIOS. This device has its programming model
in PM1x_EVT_BLK. All ACPI compliant OSes are expected to add this
power button device by default if the power button FADT flag is not
set.
On the other hand, generic hardware power button can be used by
platforms if fixed register space cannot be used for the power button
device. In order to support this, power button device object with HID
PNP0C0C is expected to be added to ACPI tables. Additionally,
POWER_BUTTON flag should be set to indicate the presence of control
method for power button.
Chrome EC mainboards implemented the generic hardware power button in
a broken manner i.e. power button object with HID PNP0C0C is added to
ACPI however none of the boards set POWER_BUTTON flag in FADT. This
results in Linux kernel adding both fixed hardware power button as
well as generic hardware power button to the list of devices present
on the system. Though this is mostly harmless, it is logically
incorrect and can confuse any userspace utilities scanning the ACPI
devices.
This change gets rid of the generic hardware power button from all
google mainboards and relies completely on the fixed hardware power
button.
BUG=b:110913245
TEST=Verified that fixed hardware power button still works correctly
on nautilus.
Change-Id: I733e69affc82ed77aa79c5eca6654aaa531476ca
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change the I2c timings to the latest measurements.
BUG=b:72442912
TEST=Boot grunt
Change-Id: I6f9538d26b77ae952ad585e569b3a836e1a09da2
Signed-off-by: Matt Wells <dawells@google.com>
Reviewed-on: https://review.coreboot.org/27553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is based on the Grunt variant.
BUG=b:111607004
TEST=Build Liara
Change-Id: I8f23e972be0d1665c736d61621a0caaa4c4c5551
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This is based on the Grunt variant.
BUG=b:111606874
TEST=Build Aleena
Change-Id: I6fd42db6f9f309c3c375b670cd22f818555e4195
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Put the PCIe clock pins in power-saving mode for the WiFi module to save
power.
Note: This currently does not appear to have any effect on grunt.
BUG=b:110041917
BRANCH=none
TEST=boot without this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3ff
With this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3f1
Change-Id: I389815bc36b8610a30b0cbb9d73262ad392e0181
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
We should use active-state power management where possible to reduce
power consumption during normal operation. Enable these options.
Linux does not seem to enable this for AMD, and the Intel code in coreboot
does enable these options.
PCIEXP_COMMON_CLOCK is enabled also, to follow how Intel does it.
BUG=b:110041917
TEST=boot on grunt, see that WiFi and eMMC still run OK
Change-Id: Ia7c711304ffe460a9fb0d4f654a51485958239ea
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27464
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Keep the backlight off until it is needed.
BUG=b:72694972
TEST=Backlight turns on at ChromeOS splash screen, not prior.
Change-Id: Ia1aba787734e2976146ecd305dd821f0b326f0db
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
BUG=b:72694972
TEST=Backlight turns on ChromeOS resume
Change-Id: I452e2ea94b508b137cf52301df5d2d1ad5c9ab70
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable the backlight in the OS callback to SMI for APMC. This keeps
the backlight off until the OS is ready to display something.
BUG=b:72694972
TEST=Backlight turns on at ChromeOS splash screen
Change-Id: Idf32b1a3d45971883571a829a5c0c1f8563bb1f7
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the mainboard resume function and __weak variant override.
Change-Id: I808734208bd1ce81428771ea203709b53db56cd3
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
there are 3 thermal sensors and index is:
0: 1 Charger
1: 1 SOC
2: 0 CPU
it needs to adjust sensor to index 2 to have correct
CPU temperature.
BUG=b:111284412
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I27afb6c5b64b0c39d6db15e6c61ea16a1fda1ca3
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This device claims to run at 75MHz with dual read, but it is not always
reliable. Add an option to change the SPI flash speed to 16MHz, to avoid
any problems.
BUG=b:111363976
TEST=manually try to get my em100 running (it doesn't yet)
Change-Id: I78d3d32c467aac82c72d31c773bfb0f69808aed4
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This applied to AMD devices as well as Intel, although the mechanism is
different. Move the option to a common place.
BUG=b:111363976
TEST=USE=em100-mode emerge-reef coreboot
See that a message appears:
* Enabling em100 mode (slow SPI flash)
Change-Id: Iea437bdf42e7bc49b1d28c812bfc6128e3eb68bd
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:111195311
TEST=Build grunt, verify SPDs are present
Change-Id: Ief5ed5c3ca1d96b36926f1fc84c344a8d66dcda5
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/27437
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add an extra space after 8th value on each line to make it easier
to count the values.
Update the empty spd to remove two random 0x80 values.
BUG=None
TEST=None
Change-Id: If330dbf0c133f65aedddc58ecb351a80b0e45a05
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/27423
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:111079089, b:80375243
TEST=Build grunt, verify that SPDs are included.
Change-Id: Idb03a3fa0842f7f89bb8c66dedbb8a0b293569be
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/27422
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
change I2C irq to EDGE trigger
BUG=b:110962003
BRANCH=master
TEST=emerge-grunt coreboot
Raydium TS is working.
Change-Id: Iff3acf4199d23b29dff209ec1c03a731679c6cbe
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27327
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Until now, chromeec was doing keyboard initialization for the boards
that have DRIVERS_PS2_KEYBOARD selected. However, coreboot does not
leave the keyboard controller in a default reset state. This could
result in payloads or OS failing to probe the controller as there
could be stale data buffered in the controller during the handoff.
Since the boards using chromeec already perform keyboard
initialization in payload, there is no need to initialize the keyboard
in coreboot too. This change gets rid of DRIVERS_PS2_KEYBOARD
selection from all google mainboards using chromeec.
BUG=b:110024487
TEST=Keyboard works fine after booting to OS even if user hits keys
during BIOS to OS handoff.
Change-Id: I1f49b060eb005c0f2b86f9d68d6758954eeb3cf0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27291
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Put the PCIe clock pins in power-saving mode for the BayHub eMMC bridge to
save power. This requires use of an additional register (Misc control
register 2) and another bit in the existing 'protect' register. The naming
of bit 0 of that register is incorrect, based on the latest datasheet
(14 June 2018) so fix that too.
BUG=b:73726008
BRANCH=none
TEST=boot without this patch:
iotools mem_read32 0xfed80e00
0x0046ffff
With this patch:
$ iotools mem_read32 0xfed80e00
0x00463fff
Also see that the PCIe clock stops when eMMC is idle and can be started by
starting disk activity.
Change-Id: I5ad1467b2e2e151215d2dfd2ce48cd4a451fe480
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/26515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
All Grunt variants should identify as grunt in SMBIOS so that
they're recognized correctly as a unibuild Grunt variant.
BUG=b:110244268
TEST=Careena identifies as grunt
Change-Id: Iaf254149fbec9551d9220018d6d6a0a1be741538
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27117
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable keyboard backlight by Careena SKUID
Set to 10% as the same as google/snappy project
BUG=b:110065836
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I7d302c4f50528b0e6b7ef4d990f342a69cff34f5
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This code is no longer needed.
BUG=b:107537694
TEST=Build & boot on grunt
Change-Id: I71ad01f0d4c69a618d564e514ed99550b72a6b44
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This code is no longer needed. Removing Kahlee options allows some
Kconfig options to be optimized.
BUG=b:77693343
TEST=Build Grunt, verify that nothing's changed.
Change-Id: I4eeeee7f35381bba8760c8a530251c475d0ee29b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Careena uses a different keyboard backlight method, so let the EC
handle the different SKUs and backlight methods.
BUG=b:80106042
TEST=None
Change-Id: I47f7a9ac13538f0216fbb0f64fdd22f66097820c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Until these need to be separated out, use a common file for mainboard
and romstage to make upkeep easier.
BUG=b:80106042
TEST=Build Grunt and Careena
Change-Id: I65188bee1958d442bfe64637c3b93dc05583a686
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Looking at the 100MHz signal, we were violating the timing requirements.
66MHz still isn't great, but it's a good tradeoff between improving
the signal and losing boot speed time.
This slows down the boot time by about 20mS.
BUG=b:109583457
TEST=Boot grunt, look at signal on scope
Change-Id: I7ce70c992822dd17c5877226e74c1890660768c6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Configuring EC_PCH_WAKE_L as an SCI enabled GPIO allows the EC to wake
the AP from S3 on keyboard presses.
BUG=b:109759838
TEST=(1) powerd_dbus_suspend
(2) press a key on the internal keyboard
=> system resumes from S3
Change-Id: I30f72460fd588706f91f4fc3ea4ff007c96e9ebe
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/26931
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
