Age | Commit message (Collapse) | Author |
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I62ffbe36bd7b7675aa0f41a8c6e9214d04ad4ae5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49428
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 3/5 which basically is generated by
running the following command:
$ git grep -iIl "arch/acpi" | xargs sed -i 's/arch\/acpi/acpi\/acpi/g'
BUG=b:155428745
Change-Id: I16b1c45d954d6440fb9db1d3710063a47b582eae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: If85e246550abe323d6a2a7c6301e8e91858cbe3a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I09cc279b1f75952bb397de2c3f2b299255163685
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
The baseboard GPIO table definitions are too straineous to the extend
that variants need to redefine assumptions back to NC. Invert this so
that baseboard by default assumes the safer NC and move the specific
board configurations to their respective places.
This patch handles the GPP_C15 group for easier review.
BUG=b:142094759
BRANCH=none
TEST=builds
Change-Id: I578245e24895d361d80ad016a4f18204e2b6e1ca
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The baseboard GPIO table definitions are too straineous to the extend
that variants need to redefine assumptions back to NC. Invert this so
that baseboard by default assumes the safer NC and move the specific
board configurations to their respective places.
This patch handles the GPP_A* group for easier review.
BUG=b:142094759
BRANCH=none
TEST=builds
Change-Id: I29b4323ac80b1288b2562846217c4f377714fc2c
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
1. No gpio control in bootblock
2. Disable power and assert reset in ramstage gpio
3. Power on and then deassert reset at the end of ramstage gpio
4. Disable power and assert reset when entering S5
On "reboot", the amount of time the power is disabled for is
equivalent to the amount of time between triggering #4 and wrapping
around to #3, which is about 400ms on Kohaku.
Since #2 forces power off for FPMCU, S3 resume will still
not work properly.
Additionally, we must ensure that GPP_A12 is reconfigured as an output
before going to any sleep state, since user space could have configured
it to use its native3 function.
See https://review.coreboot.org/c/coreboot/+/32111 for more detail.
The control signals have been validated on a Kohaku in
the following scenarios:
1. Cold startup
2. Issuing a "reboot" command
3. Issuing a "halt -p" and powering back on within 10 seconds
4. Issuing a "halt -p" and powering back on after 10 seconds
5. Entering and leaving S3 (does not work properly)
6. Entering and leaving S0iX
BRANCH=hatch
BUG=b/142751685
TEST=Verify all signals as mentioned above
TEST=reboot
flash_fp_mcu /opt/google/biod/fw/dartmonkey_v2.0.2417-af88cc91a.bin
TEST=halt -p
# power back on within 10 seconds
flash_fp_mcu /opt/google/biod/fw/dartmonkey_v2.0.2417-af88cc91a.bin
TEST=halt -p
# power back on after 10 seconds
flash_fp_mcu /opt/google/biod/fw/dartmonkey_v2.0.2417-af88cc91a.bin
Change-Id: I2e3ff42715611d519677a4256bdd172ec98687f9
Signed-off-by: Craig Hesling <hesling@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set GPP_C4 default to low to fix leakage voltage problem on touchscreen during power on.
BUG=b:142368161
BRANCH=Master
TEST=emerge-hatch coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure touchscreen works.
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Ie9197192c9d6dfb30c10559990c6010b1b2d3a45
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36670
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
pull in the FPU VDDIO turn on to fix the power leakage problem
on FPU VDDIO and FPU CS during power on sequence.
BUG=b:138638571
BRANCH=none
TEST=emerge-hatch coreboot chromeos-bootimage
Signed-off-by: Frank_Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I3f6bf3676922e987c2e282b697a2333e2d90289e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
There was the potential for misuse of the override early GPIO table,
because if the override early GPIO table did not have a corresponding
entry in the base table, it would not get overridden, and there was
no way to know except manual inspection (this has already happened
here), so now all hatch mainboards are required to explicitly list out
all of their required early GPIOs.
TEST=booted several hatch boards, verified that they can communicate
with TPM and successfully train memory
Change-Id: I0552b08a284fd6fb41a09fef431a0d006b0cf0bd
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
This patch makes SPKR_PA_EN PIN output and high for boot beep
to work in pre-os environment.
BUG=b:135104721
BRANCH=NONE
TEST=Boot Beep is working with required ALC1011 depthcharge code
changes.
Change-Id: I012462f93e9e2bcafe5f18ce7d04e3fcd1db9ffa
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Usha P <usha.p@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Meera Ravindranath <meera.ravindranath@intel.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
|
|
Based on updated schematics, change polarity of USI_INT, and add
the reset and enable GPIOs to the touchscreen ACPI node. The stop
GPIO can't be used with the current implementation of _ON, as the
way it's wired will cause power sequencing to fail.
BUG=b:137133194, b:138240502
BRANCH=none
TEST=Compiles, don't have next board rev to test with
Change-Id: I1dfb8e649418e4c5e9b897fb4bc11393adc21ea2
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Following changes are done to enable ALC1011 codec on Helios
1. ACL1011 4 devices to I2C4
2. GPIO H13 is set to GPO as per schematics
Verified SSDT table and i2cdetect from kernel.
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Change-Id: I0d71e3bd2d4493d059a33023c1afe1b630181d4f
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Helios has a number of GPIO changes w/r/t to its baseboard.
Override early, sleep and normal GPIOs as appropriate.
BUG=b:135257452
BRANCH=none
TEST=Compile only (no boards to test with)
Change-Id: I45793ad6515df5af5b925d92106bd943374353d4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|