Age | Commit message (Expand) | Author |
2017-05-05 | google/scarlet: Enable innolux,p079zca MIPI panel | Nickey Yang |
2017-05-03 | google/gru: skip usbphy1 setup for Scarlet | philipchen |
2017-04-28 | google/gru: tpm on bob: cr50: add irq clear/irq status for tpm irq | Jeffy Chen |
2017-04-25 | google/gru: change the sd power sequence | Caesar Wang |
2017-04-24 | Kconfig: provide MAINBOARD_HAS_TPM_CR50 option | Aaron Durbin |
2017-04-19 | google/gru: change kevin boot-time center logic voltage to 925mV | Douglas Anderson |
2017-04-19 | google/gru: change center logic voltage to 900mV | Derek Basehore |
2017-04-11 | scarlet/gru: skip display because mipi driver not ready | Shunqian Zheng |
2017-04-06 | gru: Initialize I2C bus for ARC2C0608 | Philip Chen |
2017-03-28 | vboot: Move remaining features out of vendorcode/google/chromeos | Julius Werner |
2017-03-28 | vboot: Assume EC_SOFTWARE_SYNC and VIRTUAL_DEV_SWITCH by default | Julius Werner |
2017-03-09 | drivers/spi/tpm: provide Kconfig to indicate CR50 usage | Aaron Durbin |
2017-03-07 | google/gru: add MAX_SDRAM_FREQ config to choose max ddr freq | Shunqian Zheng |
2017-02-23 | google/gru: whitespace fix | Patrick Georgi |
2017-02-23 | google/gru: Tuning USB 2.0 PHY0 and PHY1 squelch detection threshold | William wu |
2017-02-23 | google/gru: update the pwm regulator | Caesar Wang |
2017-02-23 | google/gru: improve eye diagram for passing the test | Caesar Wang |
2017-02-22 | google/gru: Fix whitespace | Patrick Georgi |
2017-02-11 | google/gru: add scarlet variant | philipchen |
2017-01-22 | gru: kevin: define GPIOs used on both platforms | Vadim Bendebury |
2017-01-13 | gru: Tuning USB 2.0 PHY0 and PHY1 host-port | William wu |
2016-12-06 | Bob: Update the memory ramid of bob | Shasha Zhao |
2016-12-06 | Bob: add bob in coreboot | Shasha Zhao |
2016-12-06 | rockchip/rk3399: sdram: use register to calculate sdram sizes | Lin Huang |
2016-12-06 | google/gru: Power-cycle USB ports in developer/recovery modes | Julius Werner |
2016-12-01 | lib: put romstage_handoff implementation in own compilation unit | Aaron Durbin |
2016-11-29 | google/gru: Tune USB 2.0 PHY to increase compatibility | William wu |
2016-11-18 | google/chromeec: Add common infrastructure for boot-mode switches | Furquan Shaikh |
2016-11-17 | google/gru: Move to one CA training pattern | Derek Basehore |
2016-11-17 | google/gru: Add new CA training pattern | Derek Basehore |
2016-11-02 | rockchip/rk3399: display: Do not allocate framebuffer in coreboot | Lin Huang |
2016-11-02 | rockchip/rk3399: sdram: also prepare the index1 configuration | Lin Huang |
2016-10-25 | rockchip/rk3399: gru/kevin: drop unused sdram configs | Lin Huang |
2016-10-25 | rockchip/rk3399: reset system if DDR init fails | Lin Huang |
2016-10-08 | google/gru: Add USB 2.0 PHY tuning for Kevin PHY0 and PHY1 | William wu |
2016-10-07 | google/gru: drive WLAN_MODULE_RST# low as early as possible | Brian Norris |
2016-10-07 | google/gru: set W2W_DIFFCS_DLY to 5 | Lin Huang |
2016-10-07 | google/gru: pass apio number to arm-trust-firmware | Lin Huang |
2016-10-07 | google/gru: pass the gpio power supply enable pin to bl31 | Lin Huang |
2016-10-06 | rockchip: rk3399: improve write leveling flow | Jianqun Xu |
2016-10-06 | google/gru: Shrink RW_ELOG region to 4KB | Julius Werner |
2016-10-06 | rockchip: rk3399: improve sdram noc timing | Lin Huang |
2016-10-06 | rockchip/rk3399: lower kevin board sdram frequency to 800MHz | Lin Huang |
2016-10-06 | rockchip/rk3399: Move big CPU cluster initialization into ramstage | Julius Werner |
2016-10-04 | google/gru: Ensure correct pull resistors for special-function pins | Julius Werner |
2016-10-04 | gru: Increase SPI speed to 33MHz | Simon Glass |
2016-10-04 | google/gru: Init the PWM pinmux after setting up the PWM | Douglas Anderson |
2016-10-02 | Kconfig: Update default hex values to start with 0x | Martin Roth |
2016-09-20 | gru/kevin: Decrease voltage for little cpu 1.5G to 1.15v | Shunqian Zheng |
2016-09-20 | google/gru: Fix up PWM regulator ranges | Julius Werner |
2016-09-20 | Gru: Increase bit-per-pixel to 32 | Daisuke Nojiri |
2016-09-20 | gru: Add watchdog reset support | Julius Werner |
2016-09-20 | gru: Add USB 2.0 PHY tuning for Kevin | Julius Werner |
2016-08-31 | rockchip/rk3399: Add pwm_regulator.c for pwm then ramp boot up cpu | Eric Gao |
2016-08-31 | rockchip/rk3399: Move romstage.c to mainboard/gru | Shunqian Zheng |
2016-08-27 | gru: Make SDRAM parameters individual struct files in CBFS | Julius Werner |
2016-08-19 | rockchip/rk3399 & gru/kevin: support sdram 933MHz on kevin | Lin Huang |
2016-08-18 | Kconfig: rename BOOT_MEDIA_SPI_BUS to BOOT_DEVICE_SPI_FLASH_BUS | Aaron Durbin |
2016-08-16 | Revert "rockchip: rk3399: enable sdhci clk for emmc" | Shunqian Zheng |
2016-08-13 | Revert "gru: Show the current time on start-up" | Julius Werner |
2016-08-11 | rockchip/rk3399: Add code to neuter Type-C PHY for firmware USB | Julius Werner |
2016-08-09 | google/gru: Fix rk3399-gru write protect | Douglas Anderson |
2016-08-09 | google/gru: Update board/RAM ID ADC values | Julius Werner |
2016-08-03 | google/gru: Add code to support I2C TPM for Kevin | Julius Werner |
2016-08-03 | google/gru: Add support for Gru rev1 | Julius Werner |
2016-07-28 | google/gru & kevin: Update DRAM configuration | Lin Huang |
2016-07-28 | chromeos: Clean up elog handling | Furquan Shaikh |
2016-07-28 | vboot: Separate vboot from chromeos | Furquan Shaikh |
2016-07-25 | google/gru: Change UART _Static_assert() condition to #if | Julius Werner |
2016-07-18 | gru: implement hw reset function | Vadim Bendebury |
2016-07-13 | gru: Enable TPM2 | Vadim Bendebury |
2016-07-13 | oak/gru: Fix derivative Kconfigs | Julius Werner |
2016-07-12 | google/gru: Read RAM & board ids from the ADC | Shelley Chen |
2016-07-12 | google/gru: Enable coreboot read recovery event | Shelley Chen |
2016-07-12 | google/gru: enable EC software sync | Shelley Chen |
2016-07-10 | gru: include ram_code in coreboot table | Vadim Bendebury |
2016-06-24 | rockchip/rk3399: provide multiple SDRAM configurations | Lin Huang |
2016-06-24 | gru: Add elog support | Simon Glass |
2016-06-24 | gru: Add get_developer_mode_switch() | Simon Glass |
2016-06-24 | gru: Show the current time on start-up | Simon Glass |
2016-06-24 | gru: Enable EC-based RTC | Simon Glass |
2016-06-23 | rockchip/rk3399: correct sdram inc file DENALI_CTL_217_DATA value | Lin Huang |
2016-06-23 | gru: kevin: initialize cr50 SPI interface | Vadim Bendebury |
2016-06-21 | rockchip: kevin/gru: Slow memory down to 300 MHz | Douglas Anderson |
2016-06-21 | rockchip: gru: pass poweroff gpio parameter to BL31 | Lin Huang |
2016-06-21 | rockchip: gru: pass reset gpio parameter to BL31 | Lin Huang |
2016-06-12 | rockchip: gru: Add USB DRD DWC3 controller support | Liangfeng Wu |
2016-06-08 | rockchip: rk3399: Add support i2s | Xing Zheng |
2016-06-08 | gru: kevin: enable EC SPI interface | Vadim Bendebury |
2016-06-08 | gru: kevin: configure board GPIOs | Vadim Bendebury |
2016-06-08 | gru: kevin: define GPIOs used on both platforms | Vadim Bendebury |
2016-06-07 | Kevin/Gru : Update Board ID table. | jongpil19.jung |
2016-06-07 | rockchip: gru: update the hynix lpddr3 config to run at 928MHz | Shunqian Zheng |
2016-06-03 | rockchip: gru: enable eDP display | Lin Huang |
2016-05-18 | rockchip: rk3399: enable sdhci clk for emmc | Shunqian Zheng |
2016-05-18 | rockchip: rk3399: configure emmc clk | Lin Huang |
2016-05-18 | rk3399: set proper configuration of SDMMC interface | Vadim Bendebury |
2016-05-18 | gru: set correct gpio for SD card detect | Vadim Bendebury |
2016-05-18 | Gru: support 4GB sdram on gru | Lin Huang |
2016-05-09 | google/gru: enable pp1500 and pp3000 rails as soon as possible | Vadim Bendebury |