| Age | Commit message (Collapse) | Author |
|---|
|
Going forward it's important to note when a CR50 is expected
to be present in the system. Additionally, this Kconfig addition
provides symmetry with the equivalent i2c Kconfig option.
BUG=b:35775104
Change-Id: Ifbd42b8a22f407534b23459713558c77cde6935d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18680
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
Gru/Kevin use 933 MHz (actually 928 MHz for better jitter) as max sdram
frequency, while bob uses 800 MHz.
It's normal some variants can't meet 928 MHz SI requirement and hence
have to use a lower freq as spec.
BUG=chrome-os-partner:61001
BRANCH=gru
TEST=check dpll is 800 MHz on bob
Change-Id: I6d19a351f25d1f48547715ce57c3a87d9505f6f1
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8176bfea52422c713f144ffec419752aeca66db2
Original-Change-Id: I46afba8d091f1489feeb20cafc44decaa81601fc
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/420208
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Tested-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-(cherry picked from commit eba5dff79eeedae5ff608d2d8d297ccf9c13cb55)
Original-Reviewed-on: https://chromium-review.googlesource.com/448277
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://review.coreboot.org/18581
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Follow up to https://review.coreboot.org/#/c/18460/
Change-Id: Ic3aada2acf3051622698e10d2e764050e16480d5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18475
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
According to USB 2.0 Spec Table 7-7, the High-speed squelch
detection threshold Min 100mV and Max 150mV, and we set USB
2.0 PHY0 and PHY1 squelch detection threshold to 150mV by
default, so if the amplitude of differential voltage envelope
is < 150 mV, the USB 2.0 PHYs envelope detector will indicate
it as squelch.
On Kevin board, if we connect usb device with Samsung U2 cable,
we can see that the impedance of U2 cable is too big according
to the eye-diagram test report, and this cause serious signal
attenuation at the end of receiver, the amplitude of differential
voltage falls below 150mV.
This patch aims to reduce the PHY0 and PHY1 otg-ports squelch
detection threshold to 125mV (host-ports still use 150mV by
default), this is helpful to increase USB 2.0 PHY compatibility.
BRANCH=gru
BUG=chrome-os-partner:62320
TEST=Plug Samsung U2 cable + SEC P3 HDD 500GB/Galaxy S3 into
Type-C port, check if the USB device can be detected.
Change-Id: Ia0a2d354781c2ac757938409490f7c4eecdffe61
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7d74311c25762668386061234df0562f84b7203e
Original-Change-Id: Ib20772f8fc2484d34c69f5938818aaa81ded7ed8
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/431015
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Inno Park <ih.yoo.park@samsung.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18462
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
As David commented the "Bob and other follow-ons match Gru, Kevin should
be the special case here", and update the calculations value for gru/bob
board.
From the actual tests, some regulator voltage than the actual set of less
than 20mv on bob board. (e.g: little-cpus and Center-logic) Update the
{min, max} regulator voltage for Bob board. Make sure we get the accurate
voltage.
BUG=chrome-os-partner:61497
BRANCH=none
TEST=boot up Bob, measure the voltage for little cpu and C-logic.
Change-Id: Iad881b41d67708776bfb681487cf8cec8518064e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 25e133815f49018e7496c75077b8559c207350a4
Original-Change-Id: I3098c742c7ec355c88f45bd1d93f878a7976a6b4
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/424523
Original-Reviewed-by: David Schneider <dnschneid@chromium.org>
Original-Reviewed-by: Brian Norris <briannorris@chromium.org>
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/430403
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18460
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The children of Gru should share the benefits. In the real world, Bob can't
pass the eye diagram tests.
BUG=chrome-os-partner:62714
BRANCH=firmware-gru-8785.B
TEST=build coreboot
Change-Id: I2470bbc81acdaf2458d660dca5dc307cc3038f83
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d0cb3e718a7571f602a00c08a42019851634e7fd
Original-Change-Id: I0ccb48bb52eb770ccc9c8c265b07df46b0308dd3
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/440745
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/441468
Reviewed-on: https://review.coreboot.org/18461
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I538c28fb1bc412947ef9df947fa3f6a3312aeb4b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18322
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There will be more follow-up changes.
BUG=chrome-os-partner:62377
BRANCH=None
TEST=emerge-scarlet coreboot libpayload
Change-Id: I9ca45598ff0ab12bf8063d16a86be564cf509390
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a020a9ba1228b15599e202972df0096f58b1b31c
Original-Change-Id: I4804239483f8b35bc3703aa62c2a8fd642e0234a
Original-Signed-off-by: philipchen <philipchen@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/433039
Original-Commit-Ready: Philip Chen <philipchen@chromium.org>
Original-Tested-by: Philip Chen <philipchen@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18296
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
The same GPIOs are used on both platforms, definitions are added an a
new .h to make it easier to re-use them across the code.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=panel backlight still enabled on Gru as before. The rest of the
GPIOs are used in the upcoming patches.
Change-Id: I54ef3e8dd79670bdb037baeec91430113d11bcc1
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c58788026f28af52c650da0159b93d97269ca4a9
Original-Change-Id: I1a6c5b5beb82ffcc5fea397e8e9ec2f183f4a7e0
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/346219
Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-on: https://review.coreboot.org/18176
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The commit 0ba3b2593b0c ("gru: Tuning USB 2.0 PHY to increase
compatibility") bypass ODT to set the max driver strength for
the Type-C otg-port, it works well on otg-port when connected
with USB2.0 devices.
Unfortunately, because the Type-C otg-port and host-port are
consisted in one USB2 PHY, so bypass ODT will have an effect
on both host-port and otg-port. I have tested the host-port
eye-diagram, the result shows that if we bypass ODT, the host-
port eye-diagram height will become to high, more than 500mv,
this may cause USB 2.0 high-speed enumeration failure.
This patch bypass ODT for host-port separately, and then we
can reduce the host-port driver strength without affecting
the otg-port driver strength.
BRANCH=gru
BUG=chrome-os-partner:60727
TEST=Boot system, run 'lsusb' command and check if the usb camera
and usb bluetooth are on usb 2.0 hub or usb 1.1 hub. If they are
on usb 1.1 hub, the issue happens. If not, try to run camera app
and then close camera app, repeat until find that the usb camera
is on the usb 1.1 hub.
Change-Id: Ib693e2a6f2113c06692a7bfee22d85b67ee3b165
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5ea7660b7b05080b76fc5ca5af3fa18552a03491
Original-Change-Id: Ia1f12182929673c5726df9f77f0903469b5c957a
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/425739
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Tested-by: Inno Park <ih.yoo.park@samsung.com>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/18126
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update the memory ramid.
Move to one CA training pattern.
BUG=chrome-os-partner:59454
BRANCH=firmware-gru-8785.B
TEST=Build firmware passed
Change-Id: Ic05cbc1700a13e372f63d5202459add0e984f9d8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1030a78af3d489d13508f17a79df1e65bd5afa3b
Original-Change-Id: Ibe8acb5b698cec1adcdddbb13d35a5e20a5b8c0d
Original-Reviewed-on: https://chromium-review.googlesource.com/414664
Original-Commit-Ready: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Tested-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Change-Id: I0ae46e496cd18492a2b6c7167081798c2f2479b1
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/411645
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17679
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add bob in coreboot and update as necessary.
1. Add bob HWID
2. Add supported memory source
BUG=chrome-os-partner:59454
BRANCH=firmware-gru-8785.B
TEST=Build firmware passed
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Change-Id: Iad03a293bdbbb89450f0fea0822e34a4be7064bf
Original-Commit-Id: bff788c71a43403bff2c23b38e69cc27fb869559
Original-Change-Id: I0dcf47eb911337b176f73759a2c70a9dbf4dc68b
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/411083
Original-Reviewed-by: Philip Chen <philipchen@chromium.org>
Original-(cherry picked from commit c5925dfcf59ac755a26182744b2bde59e41a37cf)
Original-Reviewed-on: https://chromium-review.googlesource.com/413744
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17678
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We may support different sdram sizes on one board in future, so
we need to calculate sdram sizes from sdram drvier.
BRANCH=None
BUG=None
TEST=boot kevin
Change-Id: I43e8f164ecdb768c051464b4dbc7d890df8055d0
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3c4d8b3cb647b2f9cebc416c298817c16d49330e
Original-Change-Id: I95d5ef34de9d79ebca3600dc7a4b9e14449606ff
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/411600
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17629
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Gru only uses USB 2.0 in firmware to avoid all the madness associated
with Type-C port orientation and USB 3.0 tuning. We do this by isolating
the SuperSpeed lines in the Type-C PHY so it looks like they aren't
connected to the device.
Unfortunately, some devices seem to already get "locked" into SuperSpeed
mode as soon as they detect Rx terminations once, and can never snap out
again on their own. Since the terminations are already connected during
power-on reset we cannot disable them fast enough to prevent this, and
the only solution we found to date is to power-cycle the whole USB port.
Now, Gru's USB port power is controlled by the EC, and unfortunately we
have no direct host command to control it. We do however have a command
to force a certain USB PD "role", and forcing our host into "sink" mode
makes it stop sourcing power to the port. So for lack of a saner
solution we'll use this to work around our problem.
BRANCH=gru
BUG=chrome-os-partner:59346
TEST=Booted Kevin in recovery mode, confirmed that my "problem stick"
gets detected immediately (whereas previously I had to unplug/replug
it). Booted Kevin to OS in both developer and normal mode and confirmed
that USB still seems to work.
Change-Id: Ib3cceba9baa170b13f01bd5c01bd413be5b441ba
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cd695eda33299e50362f1096c46f2f5260c49036
Original-Change-Id: I2db3d6d3710d18a8b8030e94eb1ac2e931f22638
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/413031
Reviewed-on: https://review.coreboot.org/17628
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Instead of putting all the functions inline just put the
current implementation into a C file. That way all the implementation
innards are not exposed.
Lastly, fix up the fallout of compilation units not including the
headers they actually use.
Change-Id: I01fd25d158c0d5016405b73a4d4df3721c281b04
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17648
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
When testing USB 2.0 compatibility with different kinds
of USB 2.0 devices on Kevin board, we find that some
USB HDDs (e.g. seagate SRD00F1 1TB HDD) and some smart
phones (e.g. galaxy A5 smart phone) can't be detected.
And according to the error log, this issue is related
to USB 2.0 PHY signal problem.
For the USB HDD, error log is:
[ 592.557724] usb 5-1: new high-speed USB device number 2 using xhci-hcd
[ 592.847735] usb 5-1: new high-speed USB device number 3 using xhci-hcd
[ 593.473720] usb 5-1: new high-speed USB device number 6 using xhci-hcd
[ 594.187717] usb 5-1: new high-speed USB device number 9 using xhci-hcd
[ 595.020717] usb 5-1: new high-speed USB device number 13 using xhci-hcd
[ 595.284730] usb 5-1: new high-speed USB device number 14 using xhci-hcd
[ 595.574816] usb 5-1: new high-speed USB device number 15 using xhci-hcd
The log shows that HDD failed to high-speed handshake.
For the smart phone, error log is:
[ 1145.661625] usb 5-1: new high-speed USB device number 2 using xhci-hcd
[ 1145.771674] usb 5-1: device descriptor read/64, error -71
[ 1145.979752] usb 5-1: device descriptor read/64, error -71
[ 1146.187721] usb 5-1: new high-speed USB device number 3 using xhci-hcd
[ 1146.301754] usb 5-1: device descriptor read/64, error -71
[ 1146.509750] usb 5-1: device descriptor read/64, error -71
[ 1146.717722] usb 5-1: new high-speed USB device number 4 using xhci-hcd
[ 1146.724393] usb 5-1: Device not responding to setup address.
[ 1146.930795] usb 5-1: Device not responding to setup address.
[ 1147.137720] usb 5-1: device not accepting address 4, error -71
[ 1147.246644] usb 5-1: new high-speed USB device number 5 using xhci-hcd
[ 1147.253336] usb 5-1: Device not responding to setup address.
[ 1147.459786] usb 5-1: Device not responding to setup address.
[ 1147.665712] usb 5-1: device not accepting address 5, error -71
[ 1147.671789] usb usb5-port1: unable to enumerate USB device
The log shows that smart phone failed to read device
descriptor, error -71 may be caused by PHY signal problem.
This patch aims to tune USB 2.0 PHY with the following
parameters to support USB HDD, smart phone and some other
potential USB 2.0 devices.
1. Disable the pre-emphasize in chirp state to avoid
high-speed handshake failure.
2. Bypass ODT auto compensation to enable set max driver
strength manually. (Bit[42] of usbphy_ctrl register is
1'b1 for bypass, and Bit[41:37] of usbphy_ctrl register
is 5'b10000 for max driver strength).
3. Bypass ODT auto refresh, and set the max bias current
tuning reference. (Bit[57] of usbphy_ctrl register is
1'b1 for bypass, and Bit[52:50] of usbphy_ctrl register
is 3b'100 for max bias current tuning reference).
We have done the USB 2.0 compliance test and compatibility test
with this patch, it works well.
BRANCH=gru
BUG=chrome-os-partner:59623
TEST=plug/unplug USB HDD or smart phone in Type-C port,
check if they can be detected successfully.
Change-Id: I275c2236b8e469bfd04e9184d007eb095657225e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7735c514d4136978133c2299f2f58da8320bb89f
Original-Change-Id: I4e6c10faa1c03af9880a89afe4731a7065eb1e4e
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/409856
Original-Commit-Ready: Eddie Cai <eddie.cai.rk@gmail.com>
Original-Tested-by: Cindy Han <cindy.han@samsung.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17566
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Instead of defining the same functions for reading/clearing boot-mode
switches from EC in every mainboard, add a common infrastructure to
enable common functions for handling boot-mode switches if
GOOGLE_CHROMEEC is being used.
Only boards that were not moved to this new infrastructure are those
that do not use GOOGLE_CHROMEEC or which rely on some mainboard specific
mechanism for reading boot-mode switches.
BUG=None
BRANCH=None
TEST=abuild compiles all boards successfully with and without ChromeOS
option.
Change-Id: I267aadea9e616464563df04b51a668b877f0d578
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17449
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This changes memory to only do CA training with one pattern,
0xfffff/0x00000 and to also make sure CA training waits for all of the
captures during training.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=boot kevin and run
stressapptest -M 1500 -s 1000
Change-Id: I0982674b4f4415f4d7865923ced93fa09bdd877e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 75cdd911cea9c4e5744fd04505b260fa5755513c
Original-Change-Id: I3b86e6d4662c6fbbf9ddef274fce191a367904e5
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/410320
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/17383
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This adds a new CA training pattern for all of the supported
frequencies. This pattern increases the hold time on CA.
BRANCH=none
BUG=chrome-os-partner:57845
TEST=boot kevin and run:
while true; do sleep 0.1; memtester 500K 1 > /dev/null; done
for several hours
Change-Id: Ie5958cf67c16247ef90ee261da9faef4ffa5b339
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8babeafe75bffcb2dab17eb007b4f5bb0eb42606
Original-Change-Id: I7f7652f88e43dc9b2f6069e60514931bf7582ed1
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/403547
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/17382
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
framebuffer address is dynamically chosen by libpayload now, so there's
no need to configure it in coreboot.
CQ-DEPEND=CL:401402
BUG=chrome-os-partner:58675
BRANCH=none
TEST=Boot from kevin, dev screen is visible
Change-Id: I9f1e581d5c63b3579b26be22ce5c8d1e71679f6f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b3b6675420592c30e1e0abc8f8e9dd6ed5abd04c
Original-Change-Id: I7e3162f24a4dc426fe4e10d74865cf0042c80db5
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/401401
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17109
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
To enable DDR Dynamic Voltage and Frequency Scaling (DVFS) we need to
train alternative configurations first, so do the training and store the
values.
BUG=None
BRANCH=None
TEST=Boot from kevin
Change-Id: I944a4b297a4ed6966893aa09553da88171307a42
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 94533ff3ba21bcb0ace00bedcf0cebb89a341be2
Original-Change-Id: I4a98bc0db5553d154fedb657e35b926a92aa80c7
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/386596
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17104
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There are some sdram configurations that are no longer used. Drop them.
BUG=None
BRANCH=None
TEST=None
Change-Id: Ib6d2d58c3071147a3095bc1ed7fa7b02c748e1a5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 111d375005ec6a3b91e47acdd676e8f1644c931c
Original-Change-Id: I5f9278093f02e785b2894faa8e8cf09ecec20325
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/399122
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17103
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We found sdram may fail in pctl_cfg(), so we check the status in this
function. If it exceeds 100ms still in this function, we will restart
the system. We also found there are rare chances DDR training fails,
so also restart system in that case.
BUG=chrome-os-partner:57988
BRANCH=None
TEST=coreboot resets on failure and eventually the system comes up
Change-Id: Icc0688da028a8f4f81eafe36bbaa79fdf2bcea74
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 89e45f8352f62e19a203316330aba14ccc5c8b11
Original-Change-Id: If4e78983abcfdfe1e0e26847448d86169e598700
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/397439
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17045
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We found that Kevin board PHY0 and PHY1 eye-diagram margin
is not enough to make compliance test pass, and the PHY0 USB
SI is worse than PHY1, because of the higher PCB impedance.
For PHY0, we can't improve the eye-diagram by SW PHY tuning,
so we need to reduce the RBIAS resistance from 133 ohm to 115
ohm, it can help to increase the eye-height.
For PHY1, we can improve the eye-diagram by setting the max
pre-emphasis level.
And after the above change, the USB2 signal amplitude will
become larger at the test point near to SOC USB2 PHY, in order
to avoid mis-trigger the disconnect detection (650mV), we need
to disable pre-emphasize in eop state.
BRANCH=None
BUG=chrome-os-partner:53863
TEST=do USB 2.0 compliance test for Kevin C0 and C1 port.
Change-Id: I95c0acd79623aeca9a0ae077b1dd3836d91fe561
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: de3cdef128966d76e7d8e2ebd641763b911c3ad5
Original-Change-Id: I00cb325b9938e4276cc77b5d6f5faa7023379608
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/390615
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16911
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
GPIO1_B3 (WLAN_MODULE_RST#) defaults as a pull-up input, but it is also
"pulled up" by 1.8V_WLAN. However, 1.8V_WLAN remains low for some time
during early boot. This leaves the signal floating somewhere in the
middle.
This has two potential issues:
(1) we're leaking some power for some (hopefully) short period of time
(2) we are possibly screwing with the Wifi power sequence; we aren't
supposed to deassert PDn (i.e., MODULE_RST#) until all the rails
have fully ramped for some period of time
Neither of the above issues are likely to be significant, but it is nice
to fix, I expect.
BRANCH=gru
BUG=chrome-os-partner:54026
TEST=measure WLAN_MODULE_RST# on scope at boot time
Change-Id: Ia6af9ad6954ad8feeda33015e3f205842380939e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0e890a2787bf034d3358a33fc88c2dd8078593ab
Original-Change-Id: I120e26ad0ca486a326874986e142dcaee965b62d
Original-Signed-off-by: Brian Norris <briannorris@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/388009
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16882
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
PHY_PER_CS_TRAINING is being enabled when DDR frequency >= 666.
For per cs training, the controller should consider the PHY
delay line switch time and there should be more cycles to
switch the delay line, so update the W2W_DIFFCS_DLY_ value
from 0x1 to 0x5.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=do memtester on kevin board, and pass
Change-Id: I00df2d4724b0b77f3e7565809fb35bbd2ff01ea5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c135ea3e33d810ed322d947eb8d512d1ac119cfc
Original-Change-Id: I81b99cbc085769b7028e770509d79bd8d550820b
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/387506
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16721
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
To save power when entering suspend, gpios 2 to 4 need to be set
to input and 'pull none' mode.
Pass the APIO configuration to ATF so it can do a proper job here.
BRANCH=None
BUG=chrome-os-partner:56423
TEST=run suspend_stress_test on kevin board
Change-Id: Id57fe8f622ae3f9c2bc7e58be89518b2b846cd37
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9c42082d1ca9a6baa735821382d3e83c1f8dc9ad
Original-Change-Id: Iaf441e8e34c5591ffe7c65f6533fcf0b733ff5ac
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/378475
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16720
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We need to disable some regulators when the device goes into suspend.
This means that we need to pass some gpios to bl31, and disable these
gpios when bl31 runs the suspend function.
BRANCH=None
BUG=chrome-os-partner:56423
TEST=enter suspend, measure suspend gpio go to low
[pg: also update arm-trusted-firmware to match]
Change-Id: Ia0835e16f7e65de6dd24a892241f0af542ec5b4b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0f3332ef2136fd93f7faad579386ba5af003cf70
Original-Change-Id: I03d0407e0ef035823519a997534dcfea078a7ccd
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/374046
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16719
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
To improve sdram 800MHz and 933MHz stability, we
need to modify write leveling flow to get the
proper write leveling value.
BUG=chrome-os-partner:56940
BRANCH=none
TEST=Boot from kevin on 933MHz, and do stressapptest
Change-Id: I5b24c93d4a57917fb9af7e5e2a95d8423ccbaa7e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d84bf25b3e5de373c7913e6d534a810cb984b3fd
Original-Change-Id: I87efddf628c3683fcb85d6875e029cf3cbc482be
Original-Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Original-Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/384292
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16716
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since there's currently a limitation in coreboot's code that prevents
more than 4KB to be used by the eventlog anyway, this patch shrinks the
available RW_ELOG area in the FMAP for Gru down to 4KB. This may prove
prudent later if we ever resolve that limitation, so that tools can rely
on the area in the FMAP being the same as the area actually used by the
read-only firmware code on these boards.
BRANCH=gru
BUG=chrome-os-partner:55593
TEST=Booted Kevin, confirmed that eventlog got written normally. Ran a
reboot loop to exhaust eventlog space, confirmed that the shrink code
kicks in as expected before reaching 4KB.
Change-Id: I3c55d836c72486665a19783fe98ce9e0df174b6d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 05efb82ca00703fd92d925ebf717738e37295c18
Original-Change-Id: Ia2617681f9394e953f5beb4abf419fe8d97e6d3e
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/384585
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Simon Glass <sjg@google.com>
Reviewed-on: https://review.coreboot.org/16715
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
sdram noc timing will affect ddr latency, this patch improves
rk3399 sdram noc timing so improve memory performance.
BRANCH=gru
BUG=chrome-os-partner:57248
TEST=Boot from kevin board
Change-Id: I09e984490a7ad747ef8abfc6542d0e2c95ec19bc
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 43dfe55d713d371e39d21312772fd353614b7642
Original-Change-Id: I393e74ecdeb72930ac38ae9bcf311e5654f65162
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/382725
Original-Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Sonny Rao <sonnyrao@chromium.org>
Original-Commit-Queue: Sonny Rao <sonnyrao@chromium.org>
Reviewed-on: https://review.coreboot.org/16713
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We found some boards are not stable when sdram is run at 933Mhz.
Before we can fix it, we need to lower the sdram frequency to 800MHz.
In this patch we modify the DQS delay from 0x280 to 0x260 and extend
the DQS window.
BRANCH=None
BUG=chrome-os-partner:56940
TEST=Booted Kevin.
Change-Id: I68561c4aa4d9ab66acfa3515a42d696157aff759
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 877a7f6ad22a5bde9f9e458bcb65f133f2f001bd
Original-Change-Id: I5eab6bbe96f0dae095c5353403292022e7a25421
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/382724
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16709
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch moves the big CPU cluster initialization on the RK3399 from
the clock init bootblock function into ramstage. We're only really doing
this to put the cluster into a sane state for the OS, we're never
actually taking it out of reset ourselves... so there's no reason to do
this so early.
Also cleaned up the interface for rkclk_configure_cpu() a bit to make it
more readable.
BRANCH=None
BUG=chrome-os-partner:54906
TEST=Booted Kevin.
Change-Id: I568b891da0abb404760d120cef847737c1f9e3ec
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: bd7aa7ec3e6d211b17ed61419f80a818cee78919
Original-Change-Id: Ic3d01a51531683b53e17addf1942441663a8ea40
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/377541
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16698
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Several of the special function pins we're using in firmware have a
pre-assigned pull-up or pull-down on power-on reset. We don't want those
to interfere with any of the signaling we're trying to do on those pins,
so this patch disables them.
Also do some house-cleaning to group the bootblock code better, and
change the setup code for all SPI and I2C buses to first initialize the
controller and then mux the pins... I assume this might be a little
safer (in case the controller peripheral has some pins in a weird state
before it gets fully initialized, we don't want to mux it through too
early).
BRANCH=None
BUG=chrome-os-partner:52526
TEST=Booted Kevin.
Change-Id: I4d5bd3f7657b8113d90b65d9571583142ba10a27
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f8f7fd56e945987eb0b1124b699f676bc68d0560
Original-Change-Id: I6bcf2b9a5dc686f2b6f82bd80fc9a1a245661c47
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/382532
Reviewed-on: https://review.coreboot.org/16711
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Increase the SPI bus speed to speed up boot time. The maximum supported
speed at 1.8V is 37.5MHz, and 33MHz is the next lowest convenient speed,
given the clock parents.
BUG=chrome-os-partner:56556
BRANCH=none
TEST=boot on gru and see that things still work correctly. Total time
spent on reading from SPI reduces from 185ms to 141ms.
Change-Id: I71436c9e343b18360fa63d528dea5cfcfbc831e6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d7576f6e53e407af61160be142c3d589e864a8cf
Original-Change-Id: I55a19f523817862e081d23469e94fd795456dd67
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381313
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16708
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
If we setup the PWM _after_ the pinmux then there's a period of time
when we're driving the PWM incorrectly. Let's setup the regulator and
_then_ configure the pinmux.
This fixes no known bugs, but it is more correct and probably makes the
signals look better at bootup.
BRANCH=None
BUG=None
TEST=scope
Change-Id: I311c0eded873b65e0489373e87b88bcdd8e4b806
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: fcf4d0ba29d82cce779c0b25ead36de4a95d97a1
Original-Change-Id: I5124f48d04a18c07bbd2d54bc08ee001c9c7e8d1
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381592
Original-Reviewed-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16700
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Kconfig hex values don't need to be in quotes, and should start with
'0x'. If the default value isn't set this way, Kconfig will add the
0x to the start, and the entry can be added unnecessarily to the
defconfig since it's "different" than what was set by the default.
A check for this has been added to the Kconfig lint tool.
Change-Id: I86f37340682771700011b6285e4b4af41b7e9968
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16834
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
In kernel side we set 1.1v for 1.5G, even for coreboot RO,
a higher voltage could be safer, 1.2v now seems too high.
BRANCH=none
BUG=chrome-os-partner:56948
TEST=bootup
Change-Id: I852e0d532369aad51b12770e2efb01aacf6662ce
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 000b5c099373be2a1f83c020ba23a0e79ea78fab
Original-Change-Id: Iecc620deee553c61a330353ac160aa3a36f516df
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/380896
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16583
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
We did yet another small adjustment to the PWM regulator ranges for
Kevin rev6... this patch reflects that in code. Also rewrite code and
descriptions to indicate that these new ranges are not just for Kevin,
but also planned to be used on Gru rev2 and any future Gru derivatives
(which as I understand it is the plan, right?).
BRANCH=None
BUG=chrome-os-partner:54888
TEST=Booted my rev5, for whatever that's worth...
Change-Id: Id78501453814d0257ee86a05f6dbd6118b719309
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 4e8be3f09ac16c1c9782dee634e5704e0bd6c7f9
Original-Change-Id: I723dc09b9711c7c6d2b3402d012198438309a8ff
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/379921
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16580
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This enhances gradation of some icons on vboot screens.
BUG=chrome-os-partner:56056
BRANCH=none
TEST=Booted kevin-tpm2
Change-Id: I2fc943f89386ccc6cd9293f5811182a5a51d99b0
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: bb1f0fb00d023c045305edc6c9fc655b764a4e8c
Original-Change-Id: Ieb61830b9555da232936087cdcf7c61a1e55bab4
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/376883
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16579
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch adds support to reboot the whole board after a hardware
watchdog reset, to avoid the usual TPM issues. Work 100% equivalent to
Veyron.
From my tests it looks like both SRAM and PMUSRAM get preserved across
warm reboots. I'm putting the WATCHDOG_TOMBSTONE into PMUSRAM since that
makes it easier to deal with in coreboot (PMUSRAM is currently not
mapped as cached, so we don't need to worry about flushing the results
back before reboot).
BRANCH=None
BUG=chrome-os-partner:56600
TEST='stop daisydog; cat > /dev/watchdog', press CTRL+D, wait 30
seconds. Confirm that system reboots correctly without entering recovery
and we get a HW watchdog event in the eventlog.
Change-Id: I317266df40bbb221910017d1a6bdec6a1660a511
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 3b8f3d064ad56d181191c1e1c98a73196cb8d098
Original-Change-Id: I17c5a801bef200d7592a315a955234bca11cf7a3
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/375562
Original-Commit-Queue: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16578
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch sets some magic number in magic undocumented registers that
are rumored to make USB 2.0 signal integrity better on Kevin. I don't
see any difference (unfortunately it doesn't solve the problems with
long cables on my board), but I guess it doesn't hurt either way.
BRANCH=None
BUG=chrome-os-partner:56108,chrome-os-partner:54788
TEST=Booted Kevin with USB connected through Servo. Seems to have
roughly the same failure rate as before.
Change-Id: If31fb49f1ed7218b50f24e251e54c9400db72720
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 0c5c8f0f80ea1ebb042bcb91506a6100833e7e84
Original-Change-Id: Ifbd47bf6adb63a2ca5371c0b05c5ec27a0fe3195
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/370900
Original-Reviewed-by: Guenter Roeck <groeck@chromium.org>
Original-Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-on: https://review.coreboot.org/16265
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Before, we calculate the pwm duties for cpu cores and centerlogic by
hand, adding pwm_regulator.c to handle this. The default pwm design
min/max voltage may be different between revs.
With the pwm regulator, this patch changes the little cpu frequency from
600M to 1512M, and raises CPU voltage to 1.2V correspondingly.
This also means we decide to drop the ES1 because it may fail to
bootup with 1.5G ~ 1.2v.
BRANCH=none
BUG=chrome-os-partner:54376,chrome-os-partner:54862
TEST=Bootup on kevin board
Change-Id: Id04c176bddfb9cdf3d25b65736e40249a85f6aa1
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: ee4365c787ec523b7ee1028ea100dcfbb331b3a9
Original-Change-Id: Ide75bbd92d1cbb14f934baeec0e38862bc08402b
Original-Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/364410
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16368
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The romstage.c is more board related than soc specific, like
setting the pwm regulators, so moving it to mainboard/gru.
BRANCH=none
BUG=chrome-os-partner:54819
TEST=Bootup on kevin board
Change-Id: I83c6cde9f451480e47e2b4b549cedf65b345134c
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 35feeb07131a6a9de4adde035236987391833474
Original-Change-Id: If2bf245302eb4fb20bb089c1b3ffa03909722443
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/375398
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16367
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch changes Gru SDRAM parameters from structures that just get
compiled into the romstage to individual CBFS files. This allows us to
only load the parameter set we need for the board we're booting from
flash, which reduces our boot time and the SRAM memory footprint
required to hold the romstage.
TEST=Booted Kevin.
Change-Id: Ie88a515cbdb19a794ca0a230a56bcc82bed1e550
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16274
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
We should be running faster. Faster = better.
BRANCH=None
BUG=chrome-os-partner:54873
TEST=Boot; stressapptest -M 1028 -s 10000
Change-Id: I7f855960af3142efb71cf9c15edd1da66084e9d8
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 51bfd2abb1aba839bd0b5b85e9e918f3cc4fd94d
Original-Change-Id: Iec9343763c1a5a5344959b6e8c4dee8079cf8a20
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/362822
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16241
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Provide a default value of 0 in drivers/spi as there weren't
default values aside from specific mainboards and arch/x86.
Remove any default 0 values while noting to keep the option's
default to 0.
BUG=chrome-os-partner:56151
Change-Id: If9ef585e011a46b5cd152a03e41d545b36355a61
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16192
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This reverts commit 462e1413 ("rockchip: rk3399: enable sdhci clk
for emmc")
Enabling this clock in coreboot is no longer needed as it's handled
in the kernel driver now.
BUG=chrome-os-partner:52873
TEST=boot from usb/sdcard and check there is /dev/mmcblk0
BRANCH=none
Change-Id: I92cf51f175fe56a09ab9329b29a27c77ef4328e1
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 5707d1269a253dabf825be120d1f9348ffaab6d0
Original-Change-Id: I8bca870c663d8ce8fac5daaaaf8225489f22ed13
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/367421
Original-Commit-Ready: Brian Norris <briannorris@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16152
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This reverts commit 850e45f19f498eedd80da4a97a5ce641e2cec6d5.
google_chromeec_init() is a weird function that can lead to confusing
behavior. I'm not sure how it's meant to work on the boards that use it,
but it causes problems on Kevin and other non-x86 boards have never used
it either. It doesn't really do anything anyway (the EC works fine
without an initial HELLO), so at best it's just a waste of time... let's
take it back out.
There's also no need to display the current time on every boot... other
boards don't do that and the eventlog already fills the same purpose.
Cut it out to avoid one extra host command overhead.
BRANCH=None
BUG=chrome-os-partner:55995
TEST=Recovery reasons now get correctly propagated across the EC reboot.
Change-Id: Ic3b772780d4d05e362c269969e6e4e7069482bb6
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 103d86e68cd164bea39aa1edc8668d80358edbde
Original-Change-Id: I58fd5e6094e1c8cb6368e7a4569ab9231375fbc9
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/367351
Original-Reviewed-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/16153
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The Rockchip RK3399 integrates a USB Type-C PHY in charge of things like
SuperSpeed line muxing for rotated cable orientations in the SoC. While
fancy, this is very complicated and we don't want to implement support
for the whole thing in firmware. The USB Type-C standard has
intentionally been designed in a way that the USB 2.0 (HighSpeed) lines
always "just work" in any orientation (by just shorting different pins
in the connector together) so that simple use cases like ours can get
basic USB functionality without much hassle.
However, a semi-configured Type-C PHY can confuse USB 3.0 capable
devices into thinking we're actually supporting SuperSpeed, and fail at
that rather than establishing a reliable HighSpeed connection. This
patch sets enough bits in the Type-C PHY to electrically isolate the
SuperSpeed lines from the connector so that the connected device isn't
going to get any fancy ideas and reliably falls back to USB 2.0.
Also clean up the rest of the USB code while we're at it: avoid writing
a few bits that are already in the right state from their reset values
anyway, or reading values whose content we already know for this SoC.
Rename the USB controllers to the name actually used in the Rockchip
documentation (USB OTGx) rather than the name blindly copied from
Exynos code (USB DRDx).
BRANCH=None
BUG=chrome-os-partner:54621
TEST=Plug a USB 3.0 Patriot Memory stick into both ports in all
orientations, observe how it gets reliably detected now (safe for some
known hardware issues on my board).
Change-Id: Ifce6bcddd69f2e8f2e2a2f48faf65551e084da1e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: c526906f998bf66067d3addb8b3d3a126c188b1e
Original-Change-Id: Ie80a201a58764c4d851fe4a5098a5acfc4bcebdf
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/366160
Original-Reviewed-by: liangfeng wu <wulf@rock-chips.com>
Original-Reviewed-by: Shelley Chen <shchen@chromium.org>
Original-Reviewed-by: <515506667@qq.com>
Reviewed-on: https://review.coreboot.org/16125
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The write protect GPIO is active high, not active low.
After fixing I can see this after removing the write-protect screw:
$ crossystem | grep wpsw_boot
wpsw_boot = 0
Putting the screw in shows:
$ crossystem | grep wpsw_boot
wpsw_boot = 1
Caution: this CL contains explicit material. It explicitly sets the
pullup on the WP GPIO even though that's the boot default.
BRANCH=None
BUG=chrome-os-partner:55933
TEST=See desc.
Change-Id: I23e17e3bbbe7dcd83e81814de46117491e61baaa
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: e6969f4be42c00c6e88bbb14929cf0454462ad21
Original-Change-Id: Ie65db9cf182b0a0a05ae412f86904df6b239e0f4
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/366131
Original-Tested-by: Brian Norris <briannorris@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16115
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Looks like our hardware guys have decided to change some voltage ranges
in the Gru/Kevin ADC IDs since we last wrote a table. This patch updates
it to the latest values from the Spreadsheet of Truth. Also adds further
values up to rev15.
BRANCH=none
BUG=none
TEST=none
Change-Id: I1aa093ca3abe952afd658eb7da01b325f798eaa0
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: e42b4685c91f01ce1cff61638b17042be9d575fd
Original-Change-Id: I646fd03dc385df1a8f0af8cb85ff3128cc31f8d8
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/365111
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16053
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Coming Kevin revisions will switch back to an I2C TPM. This patch adds
the required configuration options and code to support that. Since the
TPM type can currently only be changed at compile time, we can no longer
support older Kevins with the same image. In order to build for Kevin
revisions < 5, you have to explicitly override the CONFIG_GRU_HAS_TPM2.
BRANCH=None
BUG=chrome-os-partner:55523
TEST=Compiled both Kevin and Gru, confirmed that bootblock and verstage
binary had the appropriate code differences.
Change-Id: I1b2abe0f331eb103eb0a84f773ee7521d31ae5d8
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 3245bff937154f0f9f39894de9c98a75631d59d9
Original-Change-Id: I81a15c9fb037a7ca2d69818e46cbb4f9a5ae1989
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/364222
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16029
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
This patch adds support for the Gru rev1 board. This board differs from
rev0 by no longer relying on the I2C backlight booster and requiring the
same ODT SDRAM settings as newer Kevin boards.
BRANCH=None
BUG=chrome-os-partner:55087
TEST=None
Change-Id: I1428760540a0aaaa0c02c6cb5b0981294ba4df33
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 8de7bcc78c6c48c251c85185e238cea7812f7a28
Original-Change-Id: I3cb49bc644190f35300e6c618b2934956fa88e5b
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/364624
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16028
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
We need to enable DRAM ODT on kevin/gru board to improve the
DRAM signal. Note, if the DRAM ODT is enabled and set to 120ohms,
the sdram VREF need to adjust to 840mv.
This patch also makes following changes:
1. For compatiblity with the old board, add the
"sdram-lpddr3-hynix-4GB-666-no-odt.inc" and
"sdram-lpddr3-hynix-4GB-800-no-odt.inc" files
which do not enable sdram ODT.
2. Delete the 300MHz dram inc file. The 300MHz sdram config just
reduced 666MHz to 300MHz based on the 666MHz config file, and it is
not stable, so delete it.
3. Delete the 928MHz dram inc file, 928MHz sdram config still in
debuging, delete it for now.
BRANCH=none
BUG=chrome-os-partner:54871
TEST=run "stressapptest -M 1024 -s 1000" on kevin board and pass
Change-Id: If0248e1bc4cef2c298762080f1ca018653af0521
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 78d8a28e2d3489c99c9bba2c1c9aa76812e2e33f
Original-Change-Id: I35f0685782d6fb178a95780ec77c45f565dd2194
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/358763
Original-Commit-Ready: Dan Shi <dshi@chromium.org>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15813
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
1. Currenty, boot reason is being added to elog only for some
ARM32/ARM64 platforms. Change this so that boot reason is logged by
default in elog for all devices which have CHROMEOS selected.
2. Add a new option to select ELOG_WATCHDOG_RESET for the devices that
want to add details about watchdog reset in elog. This requires a
special region WATCHDOG to be present in the memlayout.
3. Remove calls to elog add boot reason and watchdog reset from
mainboards.
BUG=chrome-os-partner:55639
Change-Id: I91ff5b158cfd2a0749e7fefc498d8659f7e6aa91
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15897
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
VBOOT_VERIFY_FIRMWARE should be independent of CHROMEOS. This allows use
of verified boot library without having to stick to CHROMEOS.
BUG=chrome-os-partner:55639
Change-Id: Ia2c328712caedd230ab295b8a613e3c1ed1532d9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15867
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
_Static_assert() gets evaluated even when the code path it's in is
unreachable (e.g. inside an if (0) block). Unfortunately, Kconfigs that
depend on a disabled Kconfig are always 0, meaning that
CONFIG_CONSOLE_SERIAL_UART_ADDRESS on Gru cannot evaluate to UART2 when
CONFIG_CONSOLE_SERIAL (which it depends on) is disabled. Switch the
condition it is wrapped in to a preprocessor #if so that the
_Static_assert() is not evaluated when building without serial support.
BRANCH=None
BUG=None
TEST=Built and booted Kevin without serial
Change-Id: I391325fcc4b7d64b4866a7fce4444e2f28365b7d
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: f5e5cf0644154eca5b347ea381df3f6b28287524
Original-Change-Id: I33d51d4ef09b218c14173d39a12795f0cef6bb40
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/361581
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15810
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Asserting this GPIO will send a signal to the EC to trigger a reset
for the AP and the CR50.
BRANCH=none
BUG=chrome-os-partner:55252
TEST=the device now reboots when it needs to switch between different
boot modes instead of hanging with "failed to reboot" message.
Change-Id: I8d168e313b6983c96c80f7ad6d70bb84c1ec1d9c
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 83a4c8ff68ab24a103f2166e948eb23624ea97f7
Original-Change-Id: Idfd20977cf3682bd8933f89e8eec53005e55864e
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/360238
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15718
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
Gru and derivative boards use TPM2 to support Chrome OS verified boot.
BRANCH=none
BUG=chrome-os-partner:50645
TEST=re-built Kevin firmware, verified that TPM2 support over SPI is
enabled, and that with appropriate vboot and depthcharge patches
applied the device can boot into chrome os properly verifying RW
firmware and kernel key indices.
Change-Id: Id14a51cea49517bd2cc090ba05d71385aad5b54c
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 60e229d93d7e219e261b851f654e459eb2cf4f41
Original-Change-Id: Ic6f3c15aa23e4972bf175b2629728a338c45e44c
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/354781
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-on: https://review.coreboot.org/15606
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add a few missing Kconfig defaults for derivatives of the Oak and Gru
baseboards. Also group all Kconfigs that must change for derivatives
together for easier updating.
BRANCH=None
BUG=None
TEST=None
Change-Id: I95ebb08b4f13f09f2539b451d7b96a826ddf98f8
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: ae3f13c1dc323f4c7c4a176a4f5e1285fec312ce
Original-Change-Id: I658130e88daa2d113fd722b0527cf0e7ab66c7ef
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/357922
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15605
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
- Update so that the RAM id is read from ADC instead of
hard-coded from the config array.
- Update the boardid readings so that they are bucketed instead
of within an error margin.
BRANCH=None
BUG=chrome-os-partner:54566,chrome-os-partner:53988
TEST=hexdump /proc/device-tree/firmware/coreboot/ram-code
and boardid when OS boots up. Also verified that
voltage read in debug output returns correct id.
Change-Id: I963406d8c440cd90c3024c814c0de61d35ebe2fd
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 068705a38734d2604f71c8a7b5bf2cc15b0f7045
Original-Change-Id: I1c847558d54a0f7f9427904eeda853074ebb0e2e
Original-Signed-off-by: Shelley Chen <shchen@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/356584
Original-Reviewed-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/15586
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable reading of keyboard recovery host event from coreboot.
BUG=None
BRANCH=None
TEST=esc+refresh+power combo and make sure you
see recovery fw screen.
Change-Id: I166619d6202e23569395434e9dc1adb2a6a53296
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: f9279c8c06abb170589b1b11bf5287fbf38c9905
Original-Change-Id: Id980c77c8d7695b2c1b3343d968ad2a302d42aaa
Original-Signed-off-by: Shelley Chen <shchen@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/357841
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-on: https://review.coreboot.org/15585
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable CONFIG_EC_SOFTWARE_SYNC. Crossystem needs this to get ec RW/RO
info.
BUG=chrome-os-partner:54566
BRANCH=None
TEST=1. apreset from ec console. Check for
"VbEcSoftwareSync() check for RW update"
string in ap console.
2. Run "ectool version" from OS to check
that RO/RW version are different and
that we're in RW:
RO version: kevin_v1.1.4818-8243672
RW version: kevin_v1.1.4762-1957187
Firmware copy: RW
3. Run crossystem ecfw_act. check for
RW return value.
Change-Id: If6524f2cca4a6223ab9704d0af827e8c1072670f
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 0deb0e1c69d6bf21acf7640bf76f9196e14437d7
Original-Change-Id: I0db8235cf7d472f0aa642eea1998282d010d3433
Original-Signed-off-by: Shelley Chen <shchen@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/357811
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15584
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This is needed to ensure that the ram-code node is included in the
device tree by depthcharge.
BRANCH=none
BUG=chrome-os-partner:54566
TEST=built updated firmware, booted on kevin into Linux shell, checked
the device tree contents:
localhost ~ # od -tx1 /proc/device-tree/firmware/coreboot/ram-code
0000000 00 00 00 01
0000004
localhost #
Change-Id: Ibe96e3bc8fc0106013241738f5726783d74bd78b
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 53c002114f7044b88728c9e17150cd3a2cf1f80f
Original-Change-Id: Iba573fba9f9b88b87867c6963e48215e254319ed
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/354705
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15566
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We want to be able to easily change SDRAM clock rate for debugging
purposes. This patch adds configurations for 4 different clock rates.
Same configs are used for all rk3399 boards at 200, 666 and 800 MHz.
Kevin board does not run reliably at 666 MHz, an option for it is
added to run at 300 MHz, this option is available to Kevin only.
There is not much room left in the coreboot romstage section, this is
why the config file for 928 MHz is being added with this patch but is
not included in the code, one of the lower frequency options will have
to be dropped for the higher frequency option to be added.
BRANCH=none
BUG=chrome-os-partner:54144
TEST=run "stressapptest -M 1024 -s 3600" and pass on both kevin and
gru. Verified that on Kevin the firmware reports starting up
SDRAM at 300 MHz and on Gru at 800 MHz.
Change-Id: Ie24c1813d5a0e9f0f9bfc781cade9e28fb6eb2f1
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: ef5e4551b79c3f0531f9af35491f2c593f8482f1
Original-Change-Id: I08bccd40147ad89d851b995a8aab4d2b6da8258a
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/353493
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://review.coreboot.org/15309
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add code to start up elog. This uses the EC RTC to obtain the timestamp.
BUG=chrome-os-partner:52220
BRANCH=none
TEST=boot on gru with CONFIG_ELOG_DEBUG enabled and see elog messages
Change-Id: I4971d661b267ae8b7e3befeff482ca703b741743
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: e4e9823d8cecbf9873e78b048e389c7a737ff512
Original-Change-Id: I0fcf55b3feccf9a0ad915deb6d323b65bf2e9811
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/353822
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15306
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add this function and make it return 0, as there is no physical dev switch
(at least I think this is what we are supposed to do).
This is needed for elog to work, which is needed so we can test RTC
properly.
BUG=chrome-os-partner:52220
BRANCH=none
TEST=boot on gru with CONFIG_ELOG_DEBUG enabled and see elog messages:
elog_init()
SF: Detected W25Q64 with sector size 0x1000, total 0x800000
elog_find_flash()
FMAP: area RW_ELOG found @ 5d8000 (32768 bytes)
elog_scan_flash()
elog_is_buffer_clear(base=0x000000000031d668 size=4096)
ELOG: flash area invalid
elog_flash_erase(address=0x000000000031d668 offset=0x005d8000 size=4096)
SF: Successfully erased 4096 bytes @ 0x5d8000
elog_prepare_empty()
elog_flash_write(address=0x000000000031d668 offset=0x005d8000 size=8)
elog_scan_flash()
elog_is_buffer_clear(base=0x000000000031d668 size=4096)
elog_is_header_valid()
elog_update_event_buffer_state()
elog_is_buffer_clear(base=0x000000000031d670 size=4088)
elog_is_area_valid()
ELOG: FLASH @0x000000000031d668 [SPI 0x005d8000]
ELOG: area is 4096 bytes, full threshold 3834, shrink size 1024
elog_add_event_raw(type=16)
out: cmd=0x44: 03 b9 44 00 00 00 00 00
in-header: 03 3f 00 00 04 00 00 00
in-data: 6e 4c 00 00
elog_flash_write(address=0x000000000031d670 offset=0x005d8008 size=11)
ELOG: Event(16) added with size 11
elog_add_event_raw(type=17)
out: cmd=0x44: 03 b9 44 00 00 00 00 00
in-header: 03 3f 00 00 04 00 00 00
in-data: 6e 4c 00 00
elog_flash_write(address=0x000000000031d67b offset=0x005d8013 size=13)
ELOG: Event(17) added with size 13
elog_add_event_raw(type=A0)
out: cmd=0x44: 03 b9 44 00 00 00 00 00
in-header: 03 3f 00 00 04 00 00 00
in-data: 6e 4c 00 00
elog_flash_write(address=0x000000000031d688 offset=0x005d8020 size=9)
ELOG: Event(A0) added with size 9
elog_add_boot_reason: Logged dev mode boot
I can't actually see the timestamp, but the EC traffic is visible.
Change-Id: I82bcf296dce4f4d146edf90b23bfae955fbe9e3a
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: ffc7a7e0e7b136144d2a0b2ed21a543eafee49fa
Original-Change-Id: I1489c6b874cc49495635aec0bf303f7098455716
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/353821
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@google.com>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15305
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Display the current time from the EC.
BUG=chrome-os-partner:52220
BRANCH=none
TEST=(partial) boot on gru and see output:
Date: 1970-01-17 (Saturday) Time: 1:42:44
Then reboot ~10 seconds later and see output:
Date: 1970-01-17 (Saturday) Time: 1:42:53
Change-Id: I4288efc56f00e47f7575d0379a44871351da6200
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: d0361193e0ec135e21f0611d7fa6e5c02f2b2bfc
Original-Change-Id: I04a072c788ba3fc915e6d73703f966955bbd3e7e
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/351783
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15304
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Obtain the real-time clock value from the EC on start-up and show the
current time.
BUG=chrome-os-partner:52220
BRANCH=none
TEST=(partial) with future commits and EC clock set, boot on gru into
Linux shell and check the firmware log:
localhost ~ # grep Date: /sys/firmware/log
Date: 2016-06-20 (Monday) Time: 18:09:16
Change-Id: Id3ef791f546419c4881a891251cbb62d7596884b
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 348e9373b0e95a17f5c39ec28a480712e6e45caf
Original-Change-Id: Iff43b16a86d9fee483420ee2eff5ff3d276716a3
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/351781
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15303
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
for per cs training, there should be more cycles to switch delay line.
so increase W2W_DIFFCS_DLY_F0 value from 0x1 to 0x5.
BRANCH=none
BUG=chrome-os-partner:54144
TEST=run "stressapptest -M 1024 -s 1000" and pass
Change-Id: I11720b7c6f009789b88ca26fc5da88597ed1622e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 9de93beae09174d50a31d2df655529f71628f77c
Original-Change-Id: Ide23fff04fd63fb0afc538b610b7685756f79f8d
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/352953
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://review.coreboot.org/15307
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set up the pins and initialize the driver.
BRANCH=none
BUG=chrome-os-partner:50645, chrome-os-partner:51537
TEST=with the rest of the patches applied it is possible to
communicate with the cr50.
Change-Id: I9fc1cb84ccababa6f58b2d5beec4572dc1d79da1
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 6100471db2a00fd411afc05d621429b8f8a2f81d
Original-Change-Id: I0ccd8777288e35870658268813c9202dd850c70d
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/349852
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/15296
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
At the higher speeds stressapptest shows memory errors. We don't want
to track down random problems due to simple memory corruption, so slow
memory back down to 300 MHz until someone figures out how to make it
faster without sacrificing reliability.
BRANCH=None
BUG=chrome-os-partner:54144
TEST=stressapptest -M 1024 -s 240
Change-Id: I2417f93f65b1491a028a63ce563ed7dd7831becc
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id:
Original-Change-Id: I02182b25e677e27e8541445938f9da9ae9553fa6
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/350480
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15120
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
To support gpio power off SOC, we need to pass the power off
gpio parameter to BL31. Gru reuse tsadc overtemp pin as power
off gpio, so need to iomux to gpio function when use gpio power
off function, either in bl31 or depthcharge.
BRANCH=None
BUG=chrome-os-partner:53448
TEST=Build gru
Change-Id: Ibfe64042f39f6df1b87536b50fe432859bf74426
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id:
Original-Change-Id: Ie7a1bbea4a12753f0abac7a9142f2e032686ce31
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/349703
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15119
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
To support gpio reset SOC, we need to pass the reset gpio
parameter to BL31. Note: request BL31 have supported this
function.
BRANCH=None
BUG=chrome-os-partner:51924
TEST=Build gru
Change-Id: I182cff11ce6f5dc3354db0dc053c128b813acf9f
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id:
Original-Change-Id: I8283596565d552b1f3db31c28621a1601c226999
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/349702
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15118
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
This patch adds code to initialize the two DWC3 USB
host controllers, and uses them to initialize USB3.0
on the gru rk3399 board.
BRANCH=none
BUG=chrome-os-partner:52684
TEST=boot from USB3.0 on gru/kevin rk3399 platform
Change-Id: If6a6e56f3a7c7ce8e8b098634cfc2f250a91810d
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 0306a9e
Original-Change-Id: I796fa1133510876f75873d134ea752e1b52e40a8
Original-Signed-off-by: Liangfeng Wu <wulf@rock-chips.com>
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/347524
Original-Commit-Ready: Brian Norris <briannorris@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15112
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch enable and configure the clocks and IOMUX for i2s audio path,
and the i2s0 clock is from CPLL.
Please refer to TRM V0.3 Part 1 Chapter 3 CRU, P126/P128/P144/P154/P155
for the i2s clock div and gate setting.
BRANCH=none
BUG=chrome-os-partner:52172
TEST=boot kevin rev1, press ctrl+u and hear the beep voice.
Change-Id: Id00baac965c8b9213270ba5516e1ca684e4304a6
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 9c58fa7
Original-Change-Id: I130a874a0400712317e5e7a8b3b10a6f04586f68
Original-Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/347526
Original-Commit-Ready: Wonjoon Lee <woojoo.lee@samsung.com>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15034
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This configures and enables SPI interface #5 used for EC
communications on Gru/Kevin.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=with the appropriate depthcharge change it is possible to trigger
booting Chrome OS from the SD card by pressing '^U' on Gru
keyboard at the right time.
Change-Id: I5304bf47e030c0b9b7794752f30ffdca6c03a4f4
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: b5cc177
Original-Change-Id: I99883daa60562ccddfaeb858c1957d497f05a501
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/346632
Reviewed-on: https://review.coreboot.org/15032
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set board GPIOs as required and add their description into the
appropriate section of the coreboot table, to make them available to
depthcharge.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=with the rest of the patches applied it is possible to use
keyboard on Gru, which indicates that the EC interrupt GPIO is
properly configured. The rest of the pins will be verified later.
Change-Id: I5818bfe855f4e7faa2114484a9b7b44c7d469727
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: e02a05f
Original-Change-Id: I82be76bbd3211179e696526a34cc842cb1987e69
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/346631
Reviewed-on: https://review.coreboot.org/15031
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The same GPIOs are used on both platforms, definitions are added an a
new .h to make it easier to re-use them across the code.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=panel backlight still enabled on Gru as before. The rest of the
GPIOs are used in the upcoming patches.
Change-Id: If06f4b33720ab4bf098d23fb91322bba23fe6e90
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: c587880
Original-Change-Id: I1a6c5b5beb82ffcc5fea397e8e9ec2f183f4a7e0
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/346219
Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-on: https://review.coreboot.org/15029
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add board id table as kevin/gru configuration.
BUG=chrome-os-partner:53519
BRANCH=chromeos-2016.02
TEST=check boot on Kevin board.
Change-Id: I30c16916f3cda0ac88d2ce5a922e936a405fcc89
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 16c7b5486befd73c3e31624970ba1c97e526676f
Original-Change-Id: Ib69ed9dad8e1a9e08717545c6be19a90e0298c43
Original-Signed-off-by: jongpil19.jung <jongpil19.jung@samsung.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/345736
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15028
Tested-by: build bot (Jenkins)
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update the DDR config and DRAM driver to allow running at up to
928MHz. Kevin config/clock rate are not being changed, but Gru now
runs at 928 MHz.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=booted Kevin and Gru to Linux prompt. Ran stressapptest for 10 min on Gru,
Change-Id: I66c1a171d5c7d05b2878c7bc5eaa0d436c7a1be2
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 8baf0d82816a7ea1c4428e15caeefa2795d001f9
Original-Change-Id: I5e1d6d1025f10203da8f11afc3bbdf95f133c586
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/343984
Original-Reviewed-by: Stephen Barber <smbarber@chromium.org>
Reviewed-on: https://review.coreboot.org/15027
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch enables eDP display by:
o. setting HPD pinmux, backlight, vdd for eDP
o. setting vop mode
o. enabling VGA configs for edid
BRANCH=none
BUG=chrome-os-partner:51537
TEST=The dev screen is shown on kevin board
Change-Id: If8b07307454daa88727d317cc208d6c97de07ad7
Signed-off-by: Martin Roth <martinroth@google.com>
Original-Commit-Id: b1ad9337510f5437f691153dc68883edf273e4c7
Original-Change-Id: Id7006619b5be638b286a5402d892a5361ac1e430
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/340026
Original-Reviewed-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-on: https://review.coreboot.org/14858
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
If booting from sdcard/usb, kernel can't recognize the
/dev/mmcblk0.
Before kernel find it's root cause, we add this workaround
patch to enable clk for emmc.
BRANCH=none
BUG=chrome-os-partner:52873
TEST=boot from sdcard and check the /dev/mmcblk0 exists
Change-Id: Ie36cc6fdbc24db8c30984c02ccfe2f8aaaf30cd2
Signed-off-by: Martin Roth <martinroth@google.com>
Original-Commit-Id: 39b87ec3c73d6f56efc8c3f52b7ed759e548ee85
Original-Change-Id: I88a9cc2e3ea5a56aadfdbd94ef910daaf92a7eb7
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/341632
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/14856
Tested-by: build bot (Jenkins)
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
|
|
Select aclk_emmc and clk_emmc source from GPLL, and both to 198MHz,
that is GPLL(594MHz) divided by 3.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=boot kevin rev1 to chromeos prompt from both emmc and sdcard
TEST=LoadKernel faster, more than twice as I measured manually.
Change-Id: I2580c43b8c79049c3fe16bbf60bfa1a8e0559948
Signed-off-by: Martin Roth <martinroth@google.com>
Original-Commit-Id: 5fd37b66dcce77354e1cafab0d6e806d832c08d2
Original-Change-Id: Id22815b302af3204e0e5537af99c1577b09b0877
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/339152
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/14855
Tested-by: build bot (Jenkins)
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
|
|
For proper interface operation the drive strength on all pins is set
to 8 mA and all pull ups/pull downs disabled, this matches the current
kernel configuration.
BRANCH=none
BUG=chrome-os-partner:53257
TEST=it is possible to boot Chrome OS on Gru from various micro SD
cards which were failing to boot before.
Change-Id: Ie43e52a52cd0513d48d0ecc8ac02fbb100baf9a4
Signed-off-by: Martin Roth <martinroth@google.com>
Original-Commit-Id: 6bb0549ed728ac3c5faab6cbe16e2487400e67ed
Original-Change-Id: I5180537d3ceb74a9a2f7b3982ca94d3e2daf0369
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/344491
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/14853
Tested-by: build bot (Jenkins)
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
|
|
The only outlier at this time is Kevin rev 0, treat it specially, the
rest of the targets use the same GPIO.
BRANCH=none
BUG=none
TEST=gru still boots off SD card just fine
Change-Id: Ic603093a990d27166b16175db3303f155b4775aa
Signed-off-by: Martin Roth <martinroth@google.com>
Original-Commit-Id: 5788c5add1d1f803e7b22fb53215b6003ac04d03
Original-Change-Id: Ic5183f08dd1119f9588f243bd9e9c080d84687f9
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/344151
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/14851
Tested-by: build bot (Jenkins)
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
|
|
now we use 4GB sdram on gru board, enable it.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=boot from kevin board
Change-Id: Icc483a8ba91c5deea85e6e4009a8a132851b1853
Signed-off-by: Martin Roth <martinroth@google.com>
Original-Commit-Id: efa94aee02bedf51d73c91059b06afcbb1320282
Original-Change-Id: I26f77ff4ad9b2aa35ab5ff50f23984796f4f06bc
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/342585
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/14850
Tested-by: build bot (Jenkins)
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
|
|
The idea is that they stay low unless we know that we booted from SPI
flash. As this code runs in SPI flash - it is ok to turn these rails
on as soon as possible, and pp3000 rail it is essential for UART to
work.
Kevin rev1 and Gru designs are going to be using these pins to
control these rails. Kevin rev1 had those GPIO pins routed to two
chip enable signals, it is save to assert them high.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=kevin rev0 still boots (which does not prove much)
TEST=run coreboot on kevin rev1 to kernel
Change-Id: I5f3eb4cf5d6f04a0253574dd8b5c039eab0bae1a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 987042246672e9391087dbd5060785a379dde131
Original-Change-Id: I31bb03334ad9e3aa57db726fb43dec85014a3f05
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/341543
Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-on: https://review.coreboot.org/14729
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change reflects Kevin schematics differences, Gru will have to be
addressed separately.
BRANCH=None
BUG=None
TEST=the code still works fine on Kevin proto 1.
Change-Id: Iecae0e82e6bd4d185b49587b6053dcef8ad2162d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e821bbebe902a293b1e78cdd868f6bf3548ddd30
Original-Change-Id: Icd606285aeca1e19189f5e3d24c09b376942708b
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/340429
Original-Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: https://review.coreboot.org/14728
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
On kevin board, both the gpio2ab's io domain APIO2_VDDPST and
APIO2_VDD are 1.8V. So gpio2ab can only output 1.8V.
BRANCH=none
BUG=chrome-os-partner:52510
TEST=Apply this patch, CPU1_SDIO_PWREN(GPIO2_A2) can output 1.8V
Change-Id: Iefe58cf5ad83a8e79916ad177d148c1036283668
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9c4afee265f3f31c1defee08cb89ab3e45ff8d1a
Original-Change-Id: I0216c8efb7ef9256b878adeeee0a52335bf69f93
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/337194
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/14726
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Gru is the common name of a set of coreboot boards, each of them has
the config option BOARD_GOOGLE_GRU enabled. Now we need to add the
actual board called Gru to the set. Let's rename the common config
option to BOARD_GOOGLE_GRU_COMMON and use BOARD_GOOGLE_GRU for the
actual board.
BRANCH=none
BUG=none
TEST=with corresponding depthcharge and configuration space changes it
is possible to build the Gru board which boots the kernel using
the proper compatibility string of google,gru-rev0
Change-Id: I363d4b690b7549f50ed75d77b56e6a1e1d17b60f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 327ecc0de20ac0b93ec3cd28ef398393d4ea7c42
Original-Change-Id: Ia43278225c2d32d2af37193a77ea792551c9f8d9
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/340793
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/14724
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The Board ID on the Gru family of boards is determined by reading the
voltage from a resistor divider, each hardware revision is supposed to
have a unique resistor ratio, which allows to distinctly tell between
different Board ID.
While the long time approach to mapping resistor ratios (and voltages)
into Board ID remains under discussion, we know for sure the values
for Proto 1 and Proto 2. Let's just use them for now.
Since Board ID can be queried multiple times during boot, ideally it
should be read once and placed in the coreboot table to be available
to all coreboot stages. For now we just cache it so that at least
during the same stage the ADC has to run only once.
BRANCH=None
BUG=chrome-os-partner:51537
TEST=verified that the voltage reading on Proto 1 is as expected, and
Board ID 0 is reported.
Change-Id: I94bc7fc235dae4155feb6ca35b5ef0ab20c3ec9c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: bb4064d0af8174b6ae247cdad9378b7f4e5f22ba
Original-Change-Id: I105ea97f8862b5707b582904c6f2e3e9406a0f07
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/340428
Original-Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: https://review.coreboot.org/14722
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Make sure SD card is powered up properly.
Please refer to TRM V0.3 Part1 Page 324 for sdmmc pinmux.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=With other patches, boot into chromeos prompt
Change-Id: Ib53b05c1fce851ca7cbcc2207fce2dce3b1bfe9a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d37e688a458749e331a50c2ebf2018cba6629823
Original-Change-Id: I9f67c0bc16ddefa5ebe52a10c6d9e54194828a89
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/337192
Reviewed-on: https://review.coreboot.org/14718
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add the sdram driver for rk3399. With this patch we can boot
into depthcharge.
This patch also include a config file for lpddr3-hynix-4GB
that generated bases on its datasheet.
Please refer to TRM V0.3 Part1 Chapter 9 for DMC.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=boot to depthcharge on kevin
Change-Id: I2afcaa3b68dbad77a5fe677b835289b675ed2bef
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5d777e29942057fb7237eefa34051d1f54b19405
Original-Change-Id: Ifa1fe98a7058869518757d50678a64620610d91d
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/332562
Reviewed-on: https://review.coreboot.org/14716
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch implements spi clock driver and initialize
SPI flash rom for the baseboard gru.
There are 6 on-chip SPI controllers inside RK3399. For
SPI3, it's source clk from ppll, while the others from gpll.
Please refer to CRU session of TRM for detail.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=emerge-kevin coreboot
Change-Id: I597ae2cc8ba1bfaefdfbf6116027d009daa8e049
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4c6a9b0aedd427727ed4f4a821c5c54fb3a174b9
Original-Change-Id: I68ad859bf4fc5dacaaee5a2cd33418c729cf39b8
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/338946
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/14710
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch select gpio pins for UART2 which is the default
debug port of rk3399.
Please refer to TRM V0.3 Part1 Page 325,395 for GRF details.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=check logs from console manually
Change-Id: I91eeadd543e7e895c3972d8dd7a2195c9d78968b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0c51955e18d4ff9cd3208697666af4fa77046e0f
Original-Change-Id: I960178628f4020a59d100f2f0b2a6be487892549
Original-Signed-off-by: hunag lin <hl@rock-chips.com>
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/338945
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/14709
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
I missed this license header, and it's causing a build breakage.
Change-Id: If472e5c081bd282f0b482af629d6ec2314a2c329
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14388
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
|
|
To avoid diverging too much on an actively developed code base, keep
the changes to a separate commit that can be downstreamed more easily:
- removed unused includes
- gave kevin board a "Kevin" part number
- marked RW_LEGACY as CBFS region (to follow up upstream changes)
- moved romstage entry point to SoC code (instead of encouraging
per-board copy pasta)
Change-Id: Ief0c8db3c4af96fe2be2e2397d8874ad06fb6f1f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/14362
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Most things still need to be filled in, but this will allow
us to build boards which use this SOC.
[pg: separated out from the combined commit that added both SoC and
board. Added board_info.txt that will be added downstream, too.]
Change-Id: I7facce7b98a5d19fb77746b1aee67fff74da8150
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 27dfc39efe95025be2271e2e00e9df93b7907840
Original-Change-Id: I6f2407ff578dcd3d0daed86dd03d8f5f4edcac53
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/332385
Reviewed-on: https://review.coreboot.org/14279
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
