summaryrefslogtreecommitdiff
path: root/src/mainboard/google/gru/mainboard.c
AgeCommit message (Expand)Author
2017-12-11google/gru: Stop mucking with unused I2S0 pins in codec configJulius Werner
2017-12-07google/scarlet: update Kingdisplay kd097d04 timingLin Huang
2017-11-28google/scarlet: support kd097d04 panelLin Huang
2017-11-28google/gru: correct backlight gpioLin Huang
2017-11-28rockchip/rk3399: support dual mipi dsiLin Huang
2017-11-22google/gru: Add support for rainierEge Mihmanli
2017-11-20google/gru: Add config for scarlet-derived boardsEge Mihmanli
2017-11-06gru: Fix and export SPK_PA_EN GPIO for ScarletJulius Werner
2017-09-06google/gru: Re-enable 3V rail GPIO on ScarletJulius Werner
2017-08-31google/gru: Support Nefario rev0Philip Chen
2017-08-18include/device: Split i2c.h into threeNico Huber
2017-08-01google/gru: Correct the Sdcard control gpio setting for ScarletLin Huang
2017-07-19google/gru: Add support for Scarlet rev1Julius Werner
2017-07-19rockchip/rk3399: Adjust gpio_t format to match ARM TFJulius Werner
2017-06-15google/gru: drive the stronger pull-up for touchpadCaesar Wang
2017-05-03google/gru: skip usbphy1 setup for Scarletphilipchen
2017-04-25google/gru: change the sd power sequenceCaesar Wang
2017-04-06gru: Initialize I2C bus for ARC2C0608Philip Chen
2017-02-23google/gru: Tuning USB 2.0 PHY0 and PHY1 squelch detection thresholdWilliam wu
2017-02-23google/gru: improve eye diagram for passing the testCaesar Wang
2017-01-22gru: kevin: define GPIOs used on both platformsVadim Bendebury
2017-01-13gru: Tuning USB 2.0 PHY0 and PHY1 host-portWilliam wu
2016-12-06Bob: Update the memory ramid of bobShasha Zhao
2016-12-06Bob: add bob in corebootShasha Zhao
2016-12-06google/gru: Power-cycle USB ports in developer/recovery modesJulius Werner
2016-11-29google/gru: Tune USB 2.0 PHY to increase compatibilityWilliam wu
2016-10-08google/gru: Add USB 2.0 PHY tuning for Kevin PHY0 and PHY1William wu
2016-10-07google/gru: drive WLAN_MODULE_RST# low as early as possibleBrian Norris
2016-10-07google/gru: pass apio number to arm-trust-firmwareLin Huang
2016-10-07google/gru: pass the gpio power supply enable pin to bl31Lin Huang
2016-10-04google/gru: Ensure correct pull resistors for special-function pinsJulius Werner
2016-09-20gru: Add USB 2.0 PHY tuning for KevinJulius Werner
2016-08-16Revert "rockchip: rk3399: enable sdhci clk for emmc"Shunqian Zheng
2016-08-13Revert "gru: Show the current time on start-up"Julius Werner
2016-08-11rockchip/rk3399: Add code to neuter Type-C PHY for firmware USBJulius Werner
2016-08-03google/gru: Add support for Gru rev1Julius Werner
2016-07-28chromeos: Clean up elog handlingFurquan Shaikh
2016-06-24gru: Add elog supportSimon Glass
2016-06-24gru: Show the current time on start-upSimon Glass
2016-06-21rockchip: gru: pass poweroff gpio parameter to BL31Lin Huang
2016-06-21rockchip: gru: pass reset gpio parameter to BL31Lin Huang
2016-06-12rockchip: gru: Add USB DRD DWC3 controller supportLiangfeng Wu
2016-06-08rockchip: rk3399: Add support i2sXing Zheng
2016-06-08gru: kevin: define GPIOs used on both platformsVadim Bendebury
2016-06-03rockchip: gru: enable eDP displayLin Huang
2016-05-18rockchip: rk3399: enable sdhci clk for emmcShunqian Zheng
2016-05-18rockchip: rk3399: configure emmc clkLin Huang
2016-05-18rk3399: set proper configuration of SDMMC interfaceVadim Bendebury
2016-05-18gru: set correct gpio for SD card detectVadim Bendebury
2016-05-09google/gru: kevin: use board version specific SD detect GPIO pinVadim Bendebury
2016-05-09google/gru: power up SD cardVadim Bendebury
2016-04-16google/gru: Incorporate feedback to #14279Patrick Georgi
2016-04-16google/gru: Add a stub rk3399 mainboardhuang lin
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-18 01:17:20 +0000