Age | Commit message (Expand) | Author |
2020-05-11 | treewide: Remove "this file is part of" lines | Patrick Georgi |
2020-04-06 | mb/google/gru: Use SPDX for GPL-2.0-only files | Angel Pons |
2020-03-18 | mainboard/google: Remove copyright notices | Patrick Georgi |
2019-09-14 | arm64: Uprev Arm TF and adjust to BL31 parameter changes | Julius Werner |
2019-03-08 | coreboot: Replace all IS_ENABLED(CONFIG_XXX) with CONFIG(XXX) | Julius Werner |
2019-03-04 | device/mmio.h: Add include file for MMIO ops | Kyösti Mälkki |
2018-05-08 | mb/google: Get rid of device_t | Elyes HAOUAS |
2018-03-08 | google/scarlet: Adjust K&D power sequence from software | Brian Norris |
2018-02-02 | google/gru: Use newer version of Innolux P097PFG panel init code | Lin Huang |
2018-01-29 | google/scarlet: Add initialization sequence for Innolux P097PFG panel | Lin Huang |
2018-01-29 | rockchip/rk3399: Support LONG_WRITE type in MIPI DSI | Lin Huang |
2017-12-12 | google/scarlet: support INNOLUX P097PFG panel | Lin Huang |
2017-12-11 | google/gru: Stop mucking with unused I2S0 pins in codec config | Julius Werner |
2017-12-07 | google/scarlet: update Kingdisplay kd097d04 timing | Lin Huang |
2017-11-28 | google/scarlet: support kd097d04 panel | Lin Huang |
2017-11-28 | google/gru: correct backlight gpio | Lin Huang |
2017-11-28 | rockchip/rk3399: support dual mipi dsi | Lin Huang |
2017-11-22 | google/gru: Add support for rainier | Ege Mihmanli |
2017-11-20 | google/gru: Add config for scarlet-derived boards | Ege Mihmanli |
2017-11-06 | gru: Fix and export SPK_PA_EN GPIO for Scarlet | Julius Werner |
2017-09-06 | google/gru: Re-enable 3V rail GPIO on Scarlet | Julius Werner |
2017-08-31 | google/gru: Support Nefario rev0 | Philip Chen |
2017-08-18 | include/device: Split i2c.h into three | Nico Huber |
2017-08-01 | google/gru: Correct the Sdcard control gpio setting for Scarlet | Lin Huang |
2017-07-19 | google/gru: Add support for Scarlet rev1 | Julius Werner |
2017-07-19 | rockchip/rk3399: Adjust gpio_t format to match ARM TF | Julius Werner |
2017-06-15 | google/gru: drive the stronger pull-up for touchpad | Caesar Wang |
2017-05-03 | google/gru: skip usbphy1 setup for Scarlet | philipchen |
2017-04-25 | google/gru: change the sd power sequence | Caesar Wang |
2017-04-06 | gru: Initialize I2C bus for ARC2C0608 | Philip Chen |
2017-02-23 | google/gru: Tuning USB 2.0 PHY0 and PHY1 squelch detection threshold | William wu |
2017-02-23 | google/gru: improve eye diagram for passing the test | Caesar Wang |
2017-01-22 | gru: kevin: define GPIOs used on both platforms | Vadim Bendebury |
2017-01-13 | gru: Tuning USB 2.0 PHY0 and PHY1 host-port | William wu |
2016-12-06 | Bob: Update the memory ramid of bob | Shasha Zhao |
2016-12-06 | Bob: add bob in coreboot | Shasha Zhao |
2016-12-06 | google/gru: Power-cycle USB ports in developer/recovery modes | Julius Werner |
2016-11-29 | google/gru: Tune USB 2.0 PHY to increase compatibility | William wu |
2016-10-08 | google/gru: Add USB 2.0 PHY tuning for Kevin PHY0 and PHY1 | William wu |
2016-10-07 | google/gru: drive WLAN_MODULE_RST# low as early as possible | Brian Norris |
2016-10-07 | google/gru: pass apio number to arm-trust-firmware | Lin Huang |
2016-10-07 | google/gru: pass the gpio power supply enable pin to bl31 | Lin Huang |
2016-10-04 | google/gru: Ensure correct pull resistors for special-function pins | Julius Werner |
2016-09-20 | gru: Add USB 2.0 PHY tuning for Kevin | Julius Werner |
2016-08-16 | Revert "rockchip: rk3399: enable sdhci clk for emmc" | Shunqian Zheng |
2016-08-13 | Revert "gru: Show the current time on start-up" | Julius Werner |
2016-08-11 | rockchip/rk3399: Add code to neuter Type-C PHY for firmware USB | Julius Werner |
2016-08-03 | google/gru: Add support for Gru rev1 | Julius Werner |
2016-07-28 | chromeos: Clean up elog handling | Furquan Shaikh |
2016-06-24 | gru: Add elog support | Simon Glass |
2016-06-24 | gru: Show the current time on start-up | Simon Glass |
2016-06-21 | rockchip: gru: pass poweroff gpio parameter to BL31 | Lin Huang |
2016-06-21 | rockchip: gru: pass reset gpio parameter to BL31 | Lin Huang |
2016-06-12 | rockchip: gru: Add USB DRD DWC3 controller support | Liangfeng Wu |
2016-06-08 | rockchip: rk3399: Add support i2s | Xing Zheng |
2016-06-08 | gru: kevin: define GPIOs used on both platforms | Vadim Bendebury |
2016-06-03 | rockchip: gru: enable eDP display | Lin Huang |
2016-05-18 | rockchip: rk3399: enable sdhci clk for emmc | Shunqian Zheng |
2016-05-18 | rockchip: rk3399: configure emmc clk | Lin Huang |
2016-05-18 | rk3399: set proper configuration of SDMMC interface | Vadim Bendebury |
2016-05-18 | gru: set correct gpio for SD card detect | Vadim Bendebury |
2016-05-09 | google/gru: kevin: use board version specific SD detect GPIO pin | Vadim Bendebury |
2016-05-09 | google/gru: power up SD card | Vadim Bendebury |
2016-04-16 | google/gru: Incorporate feedback to #14279 | Patrick Georgi |
2016-04-16 | google/gru: Add a stub rk3399 mainboard | huang lin |