summaryrefslogtreecommitdiff
path: root/src/mainboard/google/geralt/chromeos.c
AgeCommit message (Collapse)Author
2023-07-06drivers/tpm: Move tis_plat_irq_status to cr50 driverGrzegorz Bernacki
tis_plat_irq_status() function is used only by Google TPM. It should be moved to drivers/tpm/cr50.c. The name of the function was changed to cr50_plat_irq_status(). BUG=b:277787305 TEST=Build all affected platforms Change-Id: I78dc39f2c7b44232b06947d3dfe6afa52807ced8 Signed-off-by: Grzegorz Bernacki <bernacki@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/75917 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2023-03-27mb/google/geralt: Set up open-drain ChromeOS pinsjason-ch chen
Set open-drain GPIOs for ChromeOS as input and bias-disable mode. After applying this patch, the voltage of these pins will become the expected value 1.8V (previously 1.0V), preventing wrong judgement of low/high. Reference document: MT8188G_GPIO_Formal_Application_Spec_V0.3 BUG=b:274058085 TEST=build pass Change-Id: I057716df6c59efb84fc395109db022b82ce528c4 Signed-off-by: jason-ch chen <Jason-ch.Chen@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/73963 Reviewed-by: Yidi Lin <yidilin@google.com> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-03-05mb/google/geralt: Add NAU8318 support for GeraltTrevor Wu
Add a config "USE_NAU8318" to enable NAU8318 support. NAU8318 is another speaker used in Geralt. NAU8318 supports beep function via GPIO control. So we configure the GPIO pins and pass them to the payload. BUG=b:250459803 BRANCH=none TEST=Verify beep function through CLI in depthcharge successfully. Change-Id: I21009a20809f398de4628ff0c11bcbd0e7591443 Signed-off-by: Trevor Wu <trevor.wu@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/73413 Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com> Reviewed-by: Yidi Lin <yidilin@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2023-03-05mb/google/geralt: Add MAX98390 support for GeraltTrevor Wu
Add a config "USE_MAX98390" to enable MAX98390 support. MAX98390 is an I2S smart amplifier used in Geralt. It is also the default speaker for Geralt reference board. BUG=b:250459803 BRANCH=none TEST=Verify beep function through CLI in depthcharge successfully. Change-Id: I814f440cc5ac2a13404d01fb3baafeec092b1e74 Signed-off-by: Trevor Wu <trevor.wu@mediatek.com> Signed-off-by: jason-ch chen <Jason-ch.Chen@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/73412 Reviewed-by: Yidi Lin <yidilin@google.com> Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2023-02-16mb/google/geralt: Pass XHCI_INIT_DONE to the payloadYidi Lin
BUG=b:269059211 BRANCH=none TEST=emerge-gralt coreboot Change-Id: Ia2ec6db332939f1ac629cda9a0784a12c92d91da Signed-off-by: Yidi Lin <yidilin@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/73056 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
2022-12-23mb/google/geralt: Pass SD card detect GPIO to payloadsLiju-Clr Chen
1. Add an option for SD card initialization. 2. If CONFIG SDCARD_INIT is configured, pass SD card detect GPIO to payloads for SD card detection and initialize MSDC for SD card configuration. BUG=b:244250437 TEST=build pass Signed-off-by: Liju-Clr Chen <liju-clr.chen@mediatek.com> Change-Id: I2d3683eb673f438c9190c11d4679a3ca97c76a98 Reviewed-on: https://review.coreboot.org/c/coreboot/+/71136 Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com> Reviewed-by: Yidi Lin <yidilin@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2022-12-16mb/google/geralt: Pass GPIOs to allow backlight control in payloadsBo-Chen Chen
There are two ways to control backlight in geralt: 1. MIPI/eDP panel => control backlight via the GPIOs. (`backlight chip enable` and `PWM dimming control`) 2. eDP OLED panel => enable backlight via `backlight chip enable` and control dimming over AUX. For MIPI/eDP panels(#1), both "backlight enable" and "PWM control" GPIOs will be passed from coreboot. For eDP OLED panel(#2), only the "backlight enable" GPIO will be passed. If depthcharge successfully gets the GPIOs, it will use them to control backlight. BUG=b:244208960 TEST=test firmware display pass for eDP and MIPI panels on MT8188 EVB Change-Id: I866fa219722241008e2b0d566b29edf2f6d9321f Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/70744 Reviewed-by: Yidi Lin <yidilin@google.com> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-08-03mb/google/geralt: Configure GPIOsRex-BC Chen
Configure ChromeOS specific GPIOs: - Open-drain pins to high-z mode: GPIO_EC_AP_INT_ODL, GPIO_GSC_AP_INT_ODL and GPIO_WP_ODL. - GPO mode: GPIO_AP_EC_WARM_RST_REQ, GPIO_EN_SPKR and GPIO_XHCI_INIT_DONE. This patch is based on MT8188G_GPIO_Formal_Application_Spec_V0.3. TEST=build pass BUG=b:236331724 Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Change-Id: I84d3f62ec8a3966fe1982d5d4cf6ff270450d4bf Reviewed-on: https://review.coreboot.org/c/coreboot/+/66274 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-08-03mb/google/geralt: Configure TPMRex-BC Chen
Initialize I2C bus 1 for TPM control. TEST=build pass BUG=b:236331724 Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Change-Id: If5807c9bb39260315ecbc55305def483bd2b8c51 Reviewed-on: https://review.coreboot.org/c/coreboot/+/66273 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-08-02mb/google/geralt: Enable Chrome ECRex-BC Chen
Initialize SPI bus 0 for Chrome EC control. TEST=build pass BUG=b:236331724 Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Change-Id: I6de5ea8a0273a3b0c725e4cdbcf69f4db74c5db7 Reviewed-on: https://review.coreboot.org/c/coreboot/+/66272 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2022-07-04mb/google/geralt: Add MediaTek MT8188 reference boardRex-BC Chen
Add mainboard folder and drivers for new reference board 'Geralt'. TEST=saw the coreboot uart log to bootblock BUG=b:233720142 Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Change-Id: I5e437d46097369bef535ff64e6a693b7cf67f2f1 Reviewed-on: https://review.coreboot.org/c/coreboot/+/65586 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yidi Lin <yidilin@chromium.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-22 06:23:11 +0000