summaryrefslogtreecommitdiff
path: root/src/mainboard/google/fizz
AgeCommit message (Collapse)Author
2018-03-28soc/intel/skylake: Limit xDCI feature when VBOOT is enabledDuncan Laurie
Use the common xDCI function to check if the controller is allowed in the current mode before enabling it. Otherwise, disable the PCI device if it has been enabled in devicetree. To make the SOC behavior consistent the XdciEnable config option is removed in favor of direct control by devicetree.cb and the mainboards that had defined it were adjusted accordingly. This was tested on an Eve board with xDCI enabled in devicetree.cb to ensure the xDCI device is enabled in developer mode and disabled in normal mode. Change-Id: Ic3c84beac87452f17490de32082030880834501d Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/25365 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-21mb/google/fizz: Enable I2C bus 2Zhongze Hu
I2C bus 2 goes to the custom add-in card slot and it was disalbed cuase it was idle. Google CFM add-in card is going to use this I2C bus so it needs to be re-enabled. BUG=b:73006317 TEST=Tested with add-in card on fizz hardware and verified I2C bus 2 is working properly. Change-Id: I2c9b5a9323fd51872e340c35005c4a3432716808 Signed-off-by: Zhongze Hu <frankhu@chromium.org> Reviewed-on: https://review.coreboot.org/25258 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com>
2018-03-19mb/google/fizz: Enable VMXShelley Chen
We are enabling at the kernel level, but that is triggering an issue where FSP expects it to be disabled so it forces a cold reboot on every warm reboot, clearing the ramoops logs. Enabling in BIOS so it matches what the kernel expects. This is the same change that were done for eve: https://review.coreboot.org/#/c/22449/ BUG=None BRANCH=None TEST=echo PANIC > /sys/kernel/debug/provoke-crash/DIRECT check for /dev/pstore/console-ramoops Change-Id: Icd0bd01f5aee4c89f503eebba0808a1f3059e739 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/25251 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-06mainboard/google/fizz: Check HDMI HPD and DisplayPort HPDDaisuke Nojiri
Some type-c monitors do not immediately assert HPD. If we continue to boot without HPD asserted, Depthcharge fails to show pictures on a monitor even if HPD is asserted later. Also, if an HDMI monitor is connected, no wait is needed. If only an HDMI monitor is connected, currently the API always loops until the stopwatch expires. This patch will make the AP skip DisplayPort wait loop if it detects an HDMI monitor. And if an HDMI monitor is not detected, the AP will wait for DisplayPort mode (like before) but also its HPD signal. This patch also extends the wait loop time-out to 3 seconds. BUG=b:72387533 BRANCH=none TEST=Verify firmware screen is displayed even when a type-c monitor does not immediately assert HPD. Verify if HDMI monitor is connected, AP does not wait (and firmware screen is displayed on HDMI monitor). Change-Id: I0e1afdffbebf4caf35bbb792e7f4637fae89fa49 Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/23816 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-06mb/google/fizz: Skip FSP init for UART 0Duncan Laurie
The GPIO pins for UART 0 on Fizz are routed to the add-in card slot and should not be used as a UART device. coreboot is setting the pins to GPIO Mode but FSP is re-configuring them for Native Mode and the behavior is unexpected when the kernel tries to initialize the UART device. The UART 0 device is PCI function 0 so it needs to be enabled for other functions to be visible to the OS so it can't just be disabled. Instead, set the device to PchSerialIoSkipInit so that FSP will not change the pin state. BUG=b:73006317 TEST=Tested with add-in card on fizz hardware to ensure the pin state does not change when FSP runs or the kernel boots. Change-Id: Id97c1e482ef0d5642fcf9018d802e1d0e073263d Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/24973 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-23mb/google/fizz: Enable PCIe port 11, 12Zhongze Hu
Our CFM daughter card would like to use individual PCIe lanes for two different devices on the card. dlaurie@ has reconfigured PCIe port 9-12 from 1x4 to 1x2 + 2x1 on b2b connector on fizz to meet the requirement: https://chrome-internal-review.googlesource.com/571936 We also need to enable the ports on device tree. BUG=b:72523836 TEST=none BRANCH=fizz Change-Id: Icded9850d833752680e0174b6c476e657817b319 Reviewed-on: https://chromium-review.googlesource.com/923867 Commit-Ready: Zhongze Hu <frankhu@google.com> Tested-by: Zhongze Hu <frankhu@google.com> Reviewed-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/924860 Commit-Queue: Shelley Chen <shchen@chromium.org> Tested-by: Shelley Chen <shchen@chromium.org> Signed-off-by: Zhongze Hu <frankhu@chromium.org> Reviewed-on: https://review.coreboot.org/23845 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com>
2018-02-17mb/google/fizz: Wait until display is readyDaisuke Nojiri
Fizz fails to show pictures on a type-c monitor because VBIOS runs before DisplayPort link is ready. With this patch, when firmware needs to display something, Fizz calls google_chromeec_wait_for_display to make sure display is ready. The penalty is up to 2 sec per boot in dev and rec boot. Normal boot won't affected unless there is EC update. BUG=b:72387533 BRANCH=none TEST=Verify screens are displayed on Fizz as follows: 1. Put DUT in normal mode 2. Flash EC image to trigger EC sync (critical update) 3. Trigger manual recovery (insert) 4. Hit ctrl+d to switch to dev mode (to-dev) 5. Confirm to reboot (dev warning) 6. Warm reboot (dev warning) 7. Cold reboot (dev warning) 8. Flash EC image to trigger EC sync (critical update) 9. Trigger manual recovery (insert) Change-Id: I90befe94f93e13904987acda50b2598d034b0031 Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/23746 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-02-11mb/google/fizz: Set SATA GPIOs in bootblockShelley Chen
Previously, we were seeing device boot into the recovery screen with error code 0x5a. This was root caused to the SATA GPIOs (specifically DEVSLP) not being initialized early enough, causing the SATA 1 link detection to time out and the device to reboot into recovery with 0x5a instead of booting into the OS as usual. BUG=b:69715162 BRANCH=None TEST=after flashing BIOS, set gbb flags to 0, then type reboot from the OS. Change-Id: I53913d5b7adaeb43edd0ef2d24a7cad92052d68a Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/23647 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kane Chen <kane.chen@intel.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-02-07mb/google/fizz: Set Pmax to 120 for all SKUsShelley Chen
The Pmax is calcuated from MAX(Psku1, Psku2), where Psku1, Psku2 are estimated Pmax power of U42 and U22 skus. For U42 sku, the Pmax is PL4 (71W) + ROPmax (49W) = 120W; for U22 SKU, the Pmax is PL4 (43W) + ROPmax (49W) = 92W. So Pmax is set to MAX(120W, 92W) = 120W. BUG=b:71594855 BRANCH=None TEST=Make sure correct pmax value is being passed into fsp Change-Id: Ic27fef87c869094b20438e6ee0e1eb0b35122b8d Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/23633 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Chris Ching <chingcodes@chromium.org>
2018-02-06mb/google/fizz: Determine PsysPl3 and Pl4 valuesShelley Chen
Pass in fizz-specific adapter-based PsysPl3 and Pl4 values to avoid brownouts. According to Intel doc #560604, page 74, the max time window is 64ms (code=6) and the min duty cycle we can set is 4%. BUG=b:71594855 BRANCH=None TEST=Boot to OS and check MSRs using iotools for expected values Change-Id: I06a4c5bc25f6ec036b79f6941f80e26058d64930 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/23528 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-02-05mb/google/fizz: Get OEM ID and SKU ID from ECDaisuke Nojiri
This patch makes coreboot fetch OEM ID and SKU ID from EC. If it fails, it falls back to GPIO pins. BUG=b:70294260 BRANCH=none TEST=Verify AP log shows expected OEM ID and SKU ID on Fizz. Change-Id: I06d3a205275b46660b3974bc3673d4be8e13f6d1 Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/23548 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-01-29google/fizz: Adjust PL2 and PsysPl2 values for power lossShelley Chen
Set PsysPl2 values to 90% of max adapter power for all types of adapters (typeC and barrel jack) to account for a 10% power loss from the adapter to the soc. BUG=b:71594855 BRANCH=None TEST=reboot device and make sure Pl2 and PsysPl2 MSRs are properly set with iotools rdmsr command on both U42 and U22 skus with both typeC and barrel jack power adapters. Change-Id: I8425c6d4d669449eccb9324ff58ff6d1662c5c43 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/23457 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-01-24mb/google/fizz: Add AC/DC loadline settingsGaggery Tsai
This patch adds AC and DC loadline settings since vr_config_enable is set. Without correct AD/DC loadline settings, VRs reported incorrect VID values which caused CPU freqency clipping. The clipping reason could be retrieved from MSR 0x64F. From VRTT report, the AC/DC loadline resistances are within spec, we can use default value defined in Table 6-1, doc #543977. BUG=b:70646304 BRANCH=None TEST=emerge-fizz coreboot chromeos-bootimage & Read AC/DC loadline settings from DCI to ensure the values were programmed correctly. Change-Id: Id0ce29fa5726ca3711aa4c822fb123e2de7bc48f Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-on: https://review.coreboot.org/23349 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-01-23mainboard/google/fizz: Tune audio i2c parametersShelley Chen
Tune I2C params for I2C bus 5 to ensure that the frequency does not exceed 400KHz. BUG=b:65058277 BRANCH=None TEST=Measured bus frequency for audio <= 400MHz Change-Id: I18bca023a6a0fe21e6f46f8688264d3c04d77f25 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/23359 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-01-22mb/google/fizz: Remove IccMax settings from DTGaggery Tsai
This patch removes IccMax settings from device tree since they are handled in SoC code from patch e1a75d. BUG=b:71369428 BRANCH=None TEST="USE=fw_debug emerge-fizz chromeos-mrc coreboot chromeos-bootimage" & ensure the IccMax settings passed to FSP are from SoC code. Change-Id: I6b01c50a2589d1722c5bf4aa2f44a9574df818f4 Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-on: https://review.coreboot.org/23278 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com>
2018-01-17google/fizz: Fix barrel jack values for U42 and U22Shelley Chen
Our current U22 skus (celeron and i3) actually don't support PL2, but making sure that if we do decide in the future to use it to make sure PL2 and PsysPl2 values are set appropriately. BUG=b:71594855 BRANCH=None TEST=Make sure that PsysPL2 value set to 90W with barrel jack for U42 and 65W with barrel jack for U22. Change-Id: I084d0320128a6e05948023520a30c497c41be23b Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/23294 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-01-12mb/google/fizz: update DPTF settingsKevin Chiu
TCPU: _CRT: 100 _PSV: 93 _TRT: 100/5(s) TSR0: _CRT: 83 _PSV: 70 _TRT: 100/10(s) TSR1: _CRT: 73 _PSV: 67 _TRT: 100/30(s) TCC: 6 for 94'C PL1: max: 15W min: 3W BUG=b:70294260 BRANCH=master TEST=build Change-Id: Ie17f4395d2199009fd68a600d818f2be54bc8935 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/23155 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-01-12mb/google/fizz: Disable PCH LanKane Chen
Fizz has external Lan on PCIE port. The Lan device on PCH is not used. BUG=b:70889517 Change-Id: I99894bedec14a44724ac7c22d0c894132a795b78 Signed-off-by: Kane Chen <kane.chen@intel.com> Reviewed-on: https://review.coreboot.org/23180 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-01-11google/fizz: Dynamically set PsysPl2 MSR if using type-C chargerShelley Chen
If using type-C charger, then PsysPl2 may be lower than barrel jack value of 90W, so need to override value to the max power of type-C charger. BUG=b:71594855 BRANCH=None TEST=Make sure that PsysPL2 value set to 60W with zinger, but 90W when using proper barrel jack adapter on and i7. Change-Id: If955b9af0e23f47719f001f1d73ec37113937cea Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/23182 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-01-09mb/google/fizz: Turn off SATA SALPKevin Chiu
turn off SATA SALP to prevent 0x5A/0x5B error on Sandisk SSD in below conditions: 1. reboot stress 2. FAFT BIOS qualification BUG=b:70146894,b:69984821,b:70590720 BRANCH=master TEST=pass firmware_ConsecutiveBoot 2500 loops FAFT BIOS test pass Change-Id: I5d57dd8ef256d5f0a1027ab77f63da62c6c9ce74 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/23153 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com>
2018-01-02google/fizz: Enable SataPwrOptEnable FSP UPDKane Chen
This change is to enable SataPwrOptEnable. With this change, we no longer see SError message in kernel during suspend_stress_test. BUG=b:70491485 Change-Id: Ieb991f6889c5ff3181a670bc7702314049fa983c Signed-off-by: Kane Chen <kane.chen@intel.com> Reviewed-on: https://review.coreboot.org/23019 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-12-22mb/google/fizz: revise LED0 behavior for link speed 100MbGaggery Tsai
This patch revises LED0 Green light behavior from patch 2ecf3f8c. For 100Mb link speed, LED0 should be OFF. BUG=b:65437780, b:68284778, b:69950854, b:65808944 BRANCH=None TEST=Run DUT with 100Mb and 1000Mb ethernet connection and observe LED0 is behaving as expected. Change-Id: Ia805c955711b8ce77eba087a28427a005c456fa1 Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-on: https://review.coreboot.org/22964 Reviewed-by: David Wu <david_wu@quantatw.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-22soc/intel/skylake: Add PcieRpClkSrcNumber UPD configuartion supportDivya Chellap
New UPD PcieRpClkSrcNumber introduced in FSP V2.9.2 to configure clock source number of PCIe root ports. This UPD array is set to clock source number(0-6) for all the enabled PCIe root ports, invalid(0x1F) is set for disabled PCIe root ports. BUG=b:70252901 BRANCH=None TEST= Perform the following 1. Build and boot soraka 2. Verify PCIe devices list using lspci command 3. Perform Basic Assurance Test(BAT) on soraka Change-Id: I95ca0d893338100b7e4d7d0b76c076ed7e2b040e Signed-off-by: Divya Chellap <divya.chellappa@intel.com> Reviewed-on: https://review.coreboot.org/22947 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-12-21google/fizz: Enable ec sw sync gbb by defaultShelley Chen
firmware test team is requesting that default gbb flags set to 0x39 rather than 0x239 so that it's consistent with the default gbb flags of other platforms. BUG=b:70392534 BRANCH=None TEST=emerge-fizz coreboot chromeos-bootimage gbb_utility --get --flags image-fizz.bin and make sure that it returns 0x39 instead of 0x239 Change-Id: Ib73e4619b13f6b7c2d01598c926fbbd7d7eb9bef Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/22962 Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-12-21mainboard/google/fizz: Enable S0ixShelley Chen
Enable S0ix for fizz. BUG=b:67598361 BRANCH=None TEST=None. Need to be tested with EC and kernel as well. Change-Id: I981d2cc7e969a44567b0f21f63f68c78e73f5cb5 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/22955 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-12-20mb/google/fizz: Enable mbox command for ISL VR c-state issueRizwan Qureshi
There is a potential IMVP8 issue for KBL that affects Intersil VRs Fizz is using one of the affected parts. The fix is to use an updated microcode and also send a mailbox box command from FSP. BUG=b:65499724 BRANCH=None TEST=Build and boot Fizz Change-Id: Iebfda02df88ea0d2aaf79e8449b95c0eb2165c6b Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/22763 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-12-19mb/google/fizz: Enable 2nd NIC ledsDavid Wu
This patch enables customized NIC leds as below: Green Orange (Amber) 100M off blinking 1000M on blinking BUG=b:69950854 TEST=Boot on fizz dut and observe the LEDs are behaving as expected. Perform suspend/resume test and the LEDs are still working as expected. Change-Id: Ic70587a0cd688e74b5e1ce532c5da954c80cf841 Signed-off-by: David Wu <david_wu@quantatw.com> Reviewed-on: https://review.coreboot.org/22817 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-12-15mb/google/fizz: set SataMode to AHCI modeKane Chen
For Fizz, the default should be AHCI mode and not RAID mode. Additionally, there is only one drive connector, so attaching several drives for a RAID is hard. BUG=b:70146894 Change-Id: I2a9aa2d6281a916c00ff4659a927f164ba0e0705 Signed-off-by: Kane Chen <kane.chen@intel.com> Reviewed-on: https://review.coreboot.org/22837 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-12-13mb/google/fizz: Enable SATA on port 0David Wu
Enable SATA port 0 to support SATA HDD. BUG=b:69950854 BRANCH=None TEST=emerge-fizz coreboot and boot on fizz dut Change-Id: Ifbf5950151758286f8bff7250a68d9d0b3975ef9 Signed-off-by: David Wu <david_wu@quantatw.com> Reviewed-on: https://review.coreboot.org/22815 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-08google/fizz: Set BJ max current and voltageDaisuke Nojiri
This patch makes coreboot set the max current and voltage for barrel jack adapters. BUG=b:64442692 BRANCH=none TEST=Boot Fizz. Use chgsup console command to verify the max current and voltage are set as expected. Change-Id: Ifebee09096e0935cc7d3e53920a251b0496d3c55 Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/22623 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-07boardid: Switch from Kconfig to weak functionsJulius Werner
This patch switches the board_id and ram_code helper framework to use weak functions rather than Kconfigs to determine whether the board supplies these IDs. This cuts down on the amount of boilerplate Kconfigs many boards have to set and also gives them more flexibility, such as being able to determine at runtime whether a given ID is present. Change-Id: I97d6d1103ebb2a2a7cf1ecfc45709c7e8c1a5cb0 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/22695 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-04mb/google/fizz: Enable Wake-on-Lan featureGaggery Tsai
This patch enables WOL feature. BUG=b:69290148 BRANCH=None TEST=powerd_dbus_suspend && sudo etherwake -i eth0 $MAC to make sure the system could be woken up by WOL packet. Change-Id: I1178a776db2cdb448fe6650d49ae6c0281ac1128 Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-on: https://review.coreboot.org/22606 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-11-30mainboard/google/fizz: Disable DPTF active policyDavid Wu
Use EC to perform FAN control. BUG=b:67487721,b:69404739,b:64439568 BRANCH=master TEST=emerge-fizz coreboot and boot on fizz dut Change-Id: I3394d3af9cbdb3eab1f18254909f60e2704735c3 Signed-off-by: David Wu <david_wu@quantatw.com> Reviewed-on: https://review.coreboot.org/22481 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: TH Lin <t.h_lin@quanta.corp-partner.google.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
2017-11-27google/fizz: correct memory rcomp settingsKane Chen
Follow the schematic and Doc 573387 to correct the rcomp and rcomp target settings for fizz TEST= boot ok and the system can enter and resume from S3. Change-Id: Iffa90461509cfadaca20e335a6655e549e79e749 Signed-off-by: Kane Chen <kane.chen@intel.com> Reviewed-on: https://review.coreboot.org/22479 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-11-25google/fizz: Remove tpm i2c configs from KconfigShelley Chen
We are disabling tpm over i2c, so the configs are not needed anymore. BUG=b:65056998 BRANCH=None TEST=emerge fizz and make sure can still boot up. Change-Id: Id88f32fa952801749544534442fc15d85fc1a892 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/22577 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-11-25google/fizz: Disable unused i2c linesShelley Chen
As cr50 has now switched to using SPI, no need to enable the i2c1 anymore. Additionally, disabled unused I2C devices -- I2C0, I2C2 and I2C3. BUG=b:69374421 BRANCH=None TEST=test on fizz celeron. Make sure /dev/tpm0 created on (many) reboots. cat /proc/interrupts. Make sure # interrupts for 16 after booting is reasonable (not > 10k) and idma64.0, i2c_designware.0 are not listed with that interrupt line anymore. Should look something like this: 16: 1174 0 IO-APIC 16-fasteoi i801_smbus, snd_soc_skl, AudioDSP Change-Id: Iac3e31264a937a1d7ed6bd41632e7e065317781b Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/22576 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-11-23google/fizz: Define smbios_mainboard_sku to return OEM IDsShelley Chen
Currently, mosys just returns "fizz" as model/chassis values. Returning proper OEM IDs so that mosys can return the proper variant. BUG=b:67732053 BRANCH=None TEST=mosys platform model; mosys platform chassis; Make sure returns the right variant string and not fizz. Change-Id: I42e293e833b0f7c9870dc275561ad13256836e60 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/22557 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-11-20mainboard/google/fizz: Enable separate MRC cache for recovery modeShelley Chen
Enable separate MRC cache for recovery mode. This requires change in flash layout to accomodate another region for RECOVERY_MRC_CACHE. BUG=b:69473883 TEST=Verified following scenarios: 1. Boot into recovery does not destroy normal mode MRC cache. 2. Once recovery MRC cache is populated, all future boots in recovery mode re-use data from the cache. 3. Forcing recovery mode to retrain memory causes normal mode to retrain memory as well. Change-Id: Icdfac3698507d89d98a51cfc3d756a56d2a2d648 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/22518 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-11-09mb/google/fizz: Enable NIC ledsGaggery Tsai
This patch enables customized NIC leds as follows: Green Orange (Amber) 100M off blinking 1000M on blinking BUG=b:65437780, b:68284778 TEST=Make sure the registers are programmed as expected and observe the LEDs are behaving as expected. Perform suspend/resume test and the LEDs are still working as expected. Change-Id: I9bb1367a4c742c2755d620e14ee6dfe70ee7f34b Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-on: https://review.coreboot.org/22293 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-11-08google/fizz: add VBOOT_PHYSICAL_REC_SWITCH configShelley Chen
Now that recovery button has been enabled through cr50, we can add VBOOT_PHYSICAL_REC_SWITCH config and treat the recovery button like on any other chromebox. BUG=b:37751915, b:63893483 BRANCH=None TEST=With DUT in normal mode, boot into recovery, press ctrl+d followed by pressing the recovery button. Should successfully boot into dev mode. CQ-DEPEND=CL:737477 Change-Id: I72fb42508083295e317dd06900796dc0cda753f6 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/22368 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-11-01google/fizz: enable SPD read by wordKane Chen
This is to enable SPD word access to reduce boot time. It can save 80 ~ 100 ms per DIMM. BUG=b:67021853 BRANCH=None TEST=system boot, and boot time is reduced Change-Id: Ic527a539ed634e15b939b18fff4b4e08ebb3ec57 Signed-off-by: Kane Chen <kane.chen@intel.com> Reviewed-on: https://review.coreboot.org/22267 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-20google/fizz: Set PL2 value based on sku id/charge max powerShelley Chen
Set PL2 based on either 90% of usb c charger's max power or sku id if using a barrel jack. BUG=b:37473486 BRANCH=None TEST=output debug info for different skus and make sure PL2 set correctly. Change-Id: I487fce4a5d0825a26488e71dee02400dbebbffb3 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/21772 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-18mb/google/fizz: skip reading SPD data when DUT resumes from S3Gaggery Tsai
This patch skips SPD data reading when system resumes from S3 since MRC cahce is adopted and validated in fsp_memory_init. BUG=b:67021596 TEST=Run suspend/resume on Fizz and make sure the systems are working well when system resumes from S3. Checked dmidecode information and SMBIOS type 17 data is the same with cold boot. Change-Id: I1692fca8456290d1471973b746537b5fec504e03 Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-on: https://review.coreboot.org/21987 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-16mb/google/fizz: enable AER for PCIe root portsKane Chen
Enable PCIe Advanced Error Reporting for PCIe root port 2, 3, 4 ,8. BUG=b:64798078 TEST="lspci" shows that AER is enabled in the capabilities list. Change-Id: I6438250d674e7d06cdecd8f25fadebca1973721e Signed-off-by: Kane Chen <kane.chen@intel.com> Reviewed-on: https://review.coreboot.org/21946 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-13google/fizz: Enable cr50 over SPIShelley Chen
We are changing the bootstraps in the EVTs so that the SOC communicates with cr50 over SPI instead of cr50. SPI is more reliable than I2C. Thus, disabling cr50 over I2C and enabling cr50 over SPI. BUG=b:65056998, b:62456589 BRANCH=None TEST=make sure that we can boot into kernel run cold_reset and warm_reset and make sure both boot successfully. CQ-DEPEND=CL:714237 Change-Id: I85b9a61f0305e3c7ccada79d7702234a285a6d2a Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/21970 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-10-11mainboard/google/fizz: Enable Devslp for SATA port 1Gaggery Tsai
This patch is to enable the support of device sleep for SATA port 1 and disable unused SATA port 0. BUG=b:65808359 BRANCH=None TEST=Ran "suspend_stress_test -c 2500" and passed the test. Change-Id: I33b8f5fd0c51d83e154ef7daac3274ff377bc8b3 Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-on: https://review.coreboot.org/21765 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Shelley Chen <shchen@google.com>
2017-10-09skylake mainboards: Use PAD_CFG_GPI_GPIO_DRIVER instead of PAD_CFG_GPIFurquan Shaikh
Change 1760cd3e (soc/intel/skylake: Use common/block/gpio) updated all skylake boards to use common gpio driver. Common gpio code defines PAD_CFG_GPI without GPIO_DRIVER ownership. However, for skylake PAD_CFG_GPI set GPIO_DRIVER ownership by default. This resulted in Linux kernel failing to configure all GPIO IRQs since the ownership was not set correctly. (Observed error in dmesg: "genirq: Setting trigger mode 3 for irq 201 failed (intel_gpio_irq_type+0x0/0x110)") This change fixes the above issue by replacing all uses of PAD_CFG_GPI in skylake mainboards to PAD_CFG_GPI_GPIO_DRIVER. BUG=b:67507004 TEST=Verified on soraka that the genirq error is no longer observed in dmesg. Also, cat /proc/interrupts has the interrupts configured correctly. Change-Id: I7dab302f372e56864432100a56462b92d43060ee Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/21912 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-08ec/google/chromeec: Add library function google_chromeec_events_initFurquan Shaikh
mainboard_ec_init implemented by all x86-based mainboards using chromeec performed similar tasks for initializing and recording ec events. Instead of duplicating this code across multiple boards, provide a library function google_chromeec_events_init that can be called by mainboard with appropriate inputs to perform the required actions. This change also adds a new structure google_chromeec_event_info to allow mainboards to provide information required by the library function to handle different event masks. Also, google_chromeec_log_device_events and google_chromeec_log_events no longer need to be exported. Change-Id: I1cbc24e3e1a31aed35d8527f90ed16ed15ccaa86 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/21877 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-10-04google/fizz: Configure GPP_C23 earlyDaisuke Nojiri
GPP_C23 is read by vboot_handoff to set the WP flag. Thus, it has to be configured in early_gpio_table. BUG=b:67030973 BRANCH=none TEST=Verify by wpsw_boot and wpsw_cur match. Change-Id: I96f2b53d7bc0901ffccce46b2d8ddae80c002fdc Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/21876 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-10-02google/fizz: Enable wake-on-usb attach/detachShelley Chen
BUG=b:62095784, b:35775024 BRANCH=None TEST=Run powerd_dbus_suspend from kernel. Plug in usb device and make sure wakes up. Change-Id: I214d6557998bdaf1d327c2a45532461b95d56a96 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/20421 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-09-26mainboard/google/fizz: Enable EC-EFS supportDaisuke Nojiri
BUG=b:65028930 BRANCH=none TEST=emerge-fizz coreboot. Verify Depthcharge recognize VBSD_EC_EFS. Change-Id: Ie18536982e172a45703600eec6e183c1e7c12746 Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/21640 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-09-26mainboard/google/fizz: Enable cros_ec_keyb deviceKevin Cheng
This is required to transmit button information from EC to kernel. BUG=b:65980005 BRANCH=None TEST=Verified using evtest that kernel is able to get button press/release information from EC. Change-Id: I3cd524aec47ca988d6044cb089e7aa7636e64ab2 Signed-off-by: Kevin Cheng <kevin.cheng@intel.com> Reviewed-on: https://review.coreboot.org/21633 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
2017-09-26mb/google/*: Use newly added Chrome EC boardid functionFurquan Shaikh
Instead of duplicating code across multiple mainboards, use newly added helper function to read boardid from Chrome EC. Change-Id: I1671c0a0b87d0c4c45da5340e8f17a4a798317ca Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/21682 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-09-02mainboard/google/fizz: Enable support for DPTFTsai, Gaggery
This patch adds the DPTF settings specfic to the mainboard and enables the CPU and other thermal sensors as participant device for fizz. It also enables the DPTF flag in the device tree for fizz. BUG=b:64915426 BRANCH=None TEST=emerge-fizz coreboot and run DPTF observation tool to make sure DPTF is up and running. Change-Id: Ic7d125a763f539158aa425fbba1d8a000a3465ca Signed-off-by: Tsai, Gaggery <gaggery.tsai@intel.com> Reviewed-on: https://review.coreboot.org/21147 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
2017-08-25soc/intel/skylake: Add LPC and SPI lock down config optionSubrata Banik
This patch to provide new config options to perform LPC and SPI lock down either by FSP or coreboot. Remove EISS bit programming as well. TEST=Build and boot Eve and Poppy. Change-Id: If174915b4d0c581f36b54b2b8cd970a93c6454bc Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/21068 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-07-14google/fizz: Override PL2 and SysPL2 valuesShelley Chen
Set PL2 and SysPL2 for Fizz based on cpu id. BUG=b:7473486, b:35775024 BRANCH=None TEST=On bootup make sure PL2 and PsysPL2 values set properly (through debug output) Change-Id: I5c46667fdae9d8eed5346a481753bb69f98a071b Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/20420 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-07-01mainboards: Remove unused EC event for thermal overloadDuncan Laurie
The Chrome EC event for "thermal overload" was never implemented and is being repurposed as the EC event mask is out of free bits. Remove this from the boards that were enabling it. BUG=b:36024430 TEST=build coreboot for affected boards Change-Id: I6038389ad73cef8a57aec5041bbb9dea98ed2b6e Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/20424 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-06-29lib/spd_bin: Use proper I2C addressesNico Huber
Use the plain address instead of the weird shifted encoding (e.g. if we'd use `0xa0` as address, it's actually `0x50` encoded into a write command). Change-Id: I6febb2e04e1c6de4294dfa37bde16b147a80b7a8 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/20405 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-06-28mainboard/google/fizz: Add audio devicesKevin Cheng
- Describe RT5663 headphone codec in ACPI so it can be enumerated by the OS. - Supply NHLT binaries for RT5663 BUG=b:62872377 TEST=Apply full patch set and UCM, verify basic audio works. Signed-off-by: Kevin Cheng <kevin.cheng@intel.com> Change-Id: I5bbd58b0e660cdf5089e6a6dd35a757ecf8ec076 Reviewed-on: https://review.coreboot.org/20305 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-06-20google/fizz: Enable onboard lanShelley Chen
Enable RT8168_GET_MAC_FROM_VPD in fizz Kconfig. BUG=b:62090148, b:35775024 BRANCH=None TEST=Boot to kernel. Insert mac address into VPD vpd -s ethernet_mac=<address> reboot the system. Ensure we have ip address and corresponding mac address with ifconfig. Ensure ethernet controller shows up with lspci. Change-Id: I00f63dcb56a2c9a4600c8461bc94e06ec5ab2d81 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/20232 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-06-20google/fizz: Enable cr50 over SPIShelley Chen
By default disabled. Will need to add FIZZ_USE_SPI_TPM config to enable. BUG=b:62456589, b:35775024 BRANCH=None TEST=Reboot and ensure that TPM works in verstage CQ-DEPEND=CL:530184 Change-Id: I14ce73a1c3745c996b79c4d4758ca744e63a46b4 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/20134 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-06-20google/fizz: Enable cr50 over i2cShelley Chen
BUG=b:62456589, b:35775024 BRANCH=None TEST=Reboot and ensure verstage doesn't have any TPM errors CQ-DEPEND=CL:530185 Change-Id: Icfde0f62bd058d960fcb0c6fc67f9d8f6b9462f5 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/20133 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-06-03mb/google/fizz: set SD_CDZ to edge trigger.Kane Chen
This is to align with the SD_CD GpioInt setting in acpi BUG=b:62067569 TEST=checked unused interrupt on SD_CD does not happen after s3 resume Change-Id: I40aefcb0f571e7f6773a6d20226f357707aa041a Signed-off-by: Kane Chen <kane.chen@intel.com> Reviewed-on: https://review.coreboot.org/20001 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-05-27lib/spd_bin: make SMBus SPD addresses an inputAaron Durbin
Instead of assuming the mapping of dimm number to SPD SMBus address, allow the mainboard to provide its own mapping. That way, global resources of empty SPD contents aren't wasted in order to address a dimm on a mainboard that doesn't meet the current assumption. Change-Id: Id0e79231dc2303373badaae003038a1ac06a5635 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/19915 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
2017-05-27google/fizz: Set GPP_C2 to NCShelley Chen
GPP_C2 is being used as strapping option, so should not be set to NF. Signal was floating previously, which can lead to an assertion of smbalert#. BUG=b:37681121, b:35775024 BRANCH=None TEST=powerd_dbus_suspend and ensure stays in suspend Change-Id: I68091206014621419b886b723a5681541be989bc Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/19904 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-05-17google/fizz: Configure SATAXPCIe GPIOs to use native functionShelley Chen
BUG=b:37486021, b:35775024 BRANCH=None TEST=reboot and ensure that device detects SSD Change-Id: I4a85b9f3ba1d0a4c0a753420e166d3353417a1d1 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/19554 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Shelley Chen <shchen@google.com>
2017-05-05google/fizz: Enable devices under pci 1c.0Shelley Chen
Turn on device 1c.0 in order to enable devices under it. BUG=b:37486021, b:35775024 BRANCH=None TEST=Boot from NVMe Change-Id: Ide66823283c58d2bea0c9886f762f0581741affe Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/19533 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-04-27google/fizz: Configure HDMI HPD to use native functionShelley Chen
BUG=b:37684299, b:35775024 BRANCH=None TEST=reboot and ensure graphics are displayed through HDMI port. Change-Id: I74a664b2d42f55adfa64f292f6ede4c956e16fbf Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/19451 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-04-27google/fizz: Enable SATA on port 1Shelley Chen
BUG=b:37486021 BRANCH=None TEST=compile coreboot and make sure sda and sdb show up in /sys/class/block. Change-Id: I11344a4a5fc7e5b5d907d25439f92744a5fb70da Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/19450 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-04-24mb/google/fizz: Set lid status as openNaresh G Solanki
Lid switch is not available. Hence report lid state as always open. Change-Id: Ia9c82c3ad323912bad51cf55ed80a37b3110b1ef Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Reviewed-on: https://review.coreboot.org/19219 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
2017-04-24mb/google/fizz: Configure PCI root portNaresh G Solanki
Configure PCI root port as per schematic. Change-Id: I10ef682e8c54e22f328db5105d4da39c72ac2bed Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Reviewed-on: https://review.coreboot.org/19390 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-04-24google/fizz: Configure memoryShelley Chen
Read DRAM SPD and populate MemorySpdPtr fields in UPD data structure for FSP. BUG=b:36490168, b:35775024 BRANCH=None TEST=./util/abuild/abuild -p none -t google/fizz -x -a We are currently working on bringup and have no hardware to test on yet. Change-Id: I191cc6bf1fd8aa461855c538b48fd39e3ffd7848 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/19205 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-04-13soc/intel/skylake: Split AC/DC settings for Deep Sx configDuncan Laurie
Currently when enabling Deep S3 or Deep S5 it unconditionally gets enabled in both DC and AC states. However since using Deep S3 disables some expected features like wake-on-USB it is not always desired to enable the same state in both modes. To address this split the setting and add a separate config for Deep Sx in AC and DC states. All motherboards that set this config were updated, but there is no actual change in behavior in this commit. BUG=b:36723679 BRANCH=none TEST=This commit has no runtime visible changes, I verified on Eve that the Deep SX config registers are unchanged, and it compiles for all affected boards. Change-Id: I590f145847785b5a7687f235304e988888fcea8a Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/19239 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-03-28vboot: Move remaining features out of vendorcode/google/chromeosJulius Werner
This patch attempts to finish the separation between CONFIG_VBOOT and CONFIG_CHROMEOS by moving the remaining options and code (including image generation code for things like FWID and GBB flags, which are intrinsic to vboot itself) from src/vendorcode/google/chromeos to src/vboot. Also taking this opportunity to namespace all VBOOT Kconfig options, and clean up menuconfig visibility for them (i.e. some options were visible even though they were tied to the hardware while others were invisible even though it might make sense to change them). CQ-DEPEND=CL:459088 Change-Id: I3e2e31150ebf5a96b6fe507ebeb53a41ecf88122 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18984 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-28vboot: Assume EC_SOFTWARE_SYNC and VIRTUAL_DEV_SWITCH by defaultJulius Werner
The virtualized developer switch was invented five years ago and has been used on every vboot system ever since. We shouldn't need to specify it again and again for every new board. This patch flips the Kconfig logic around and replaces CONFIG_VIRTUAL_DEV_SWITCH with CONFIG_PHYSICAL_DEV_SWITCH, so that only a few ancient boards need to set it and it fits better with CONFIG_PHYSICAL_REC_SWITCH. (Also set the latter for Lumpy which seems to have been omitted incorrectly, and hide it from menuconfig since it's a hardware parameter that shouldn't be configurable.) Since almost all our developer switches are virtual, it doesn't make sense for every board to pass a non-existent or non-functional developer mode switch in the coreboot tables, so let's get rid of that. It's also dangerously confusing for many boards to define a get_developer_mode() function that reads an actual pin (often from a debug header) which will not be honored by coreboot because CONFIG_PHYSICAL_DEV_SWITCH isn't set. Therefore, this patch removes all those non-functional instances of that function. In the future, either the board has a physical dev switch and must define it, or it doesn't and must not. In a similar sense (and since I'm touching so many board configs anyway), it's annoying that we have to keep selecting EC_SOFTWARE_SYNC. Instead, it should just be assumed by default whenever a Chrome EC is present in the system. This way, it can also still be overridden by menuconfig. CQ-DEPEND=CL:459701 Change-Id: If9cbaa7df530580a97f00ef238e3d9a8a86a4a7f Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18980 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-23google/fizz: Update device tree from schematicShelley Chen
BUG=b:35775024 BRANCH=None TEST=Compiles successfully Change-Id: I92cf9baa4c3aefc6983511543d875e74a6b0bf94 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/18944 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-03-23google/fizz: Transfer gpio from schematicShelley Chen
Transfer the gpio assignments in the fizz schematic into gpio.h. BUG=b:35775024 BRANCH=None TEST=./util/abuild/abuild -p none -t google/fizz -x -a Change-Id: If05aa2859f2511c3f616dc3fb38bca4fb8524697 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/18797 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2017-03-23google/fizz: Remove poppy-specific configsShelley Chen
- Remove spd files/directory - Remove audio blobs - Remove dptf.asl contents - Remove MKBP - Remove acpi table initialization BUG=b:35775024 BRANCH=None TEST=Compiles successfully Change-Id: I5d717d23224956ee1653c5ded28abd05cd254c3a Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/18857 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-03-23google/fizz: Add new boardShelley Chen
Creating google/fizz directory based on poppy (using kabylake and FSP 2.0). Only making name changes and Copyright year changes. Many poppy-specific configs left in and will be updated in follup CLs. BUG=b:35775024 BRANCH=None TEST=Compile fizz board Change-Id: Icab3639a53fef65e904e797028916fda879fff7c Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/18796 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 10:00:28 +0000