Age | Commit message (Collapse) | Author |
|
CONFIG_ARCH is a property of the cpu or soc rather than a property of the
board. Hence, move ARCH_* from every single board to respective cpu or soc
Kconfigs. Also update abuild to ignore ARCH_ from mainboards.
Change-Id: I6ec1206de5a20601c32d001a384a47f46e6ce479
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: http://review.coreboot.org/5570
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I2ba7a1c2b2e6ce2c00c9a2916141bed67930ba2d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5586
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
A global flag oprom_is_loaded was used to indicate to
U-boot that VGA option ROM was loaded and run, or that
native VGA init was completed on GMA device.
Implement this feature without dependency to CHROMEOS option
and replace use of global variable oprom_is_loaded with call
to gfx_get_init_done().
Change-Id: I7e1afd752f18e5346dabdee62e4f7ea08ada5faf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4309
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
It's not needed and causes build failures without CONFIG_CHROMEOS.
Change-Id: I7923717bfc5c84698044008e5f2441206041e0dd
Reported-by: Idwer Vollering <vidwer@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/5398
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
With the recent improvement 3d6ffe76f8a505c2dff5d5c6146da3d63dad6e82,
speedup by CACHE_ROM is reduced a lot.
On the other hand this makes coreboot run out of MTRRs depending on
system configuration, hence screwing up I/O access and cache
coherency in worst cases.
CACHE_ROM requires the user to sanity check their boot output because
the feature is brittle. The working configuration is dependent on I/O
hole size, ram size, and chipset. Because of this the current
implementation can leave a system configured in an inconsistent state
leading to unexpected results such as poor performance and/or
inconsistent cache-coherency
Remove this as a buggy feature until we figure out how to do it properly
if necessary.
Change-Id: I858d78a907bf042fcc21fdf7a2bf899e9f6b591d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5146
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
spd.bin can reside anywhere in CBFS, and we only use CBFS APIs to
access and read it. As such, there is no need to hardcode it, and it
can collide with mrc.bin or mrc.cache on some boards. Do not use a
specific position for spd.bin, but instead let cbfstool find the
optimal placement.
Change-Id: I496094d3c0de708813494095b7ac4be8addb4112
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5210
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
If the SerialIO devices are put into ACPI mode then it is possible
to use ACPI to instantiate the touchpad in the kernel without
needing to have a platform level driver to do the binding.
This is the "new way" of describing on-board I2C devices and the
upstream kernel is starting to add ACPI IDs to drivers so they can
be used in this fashion. For the Cypress touchpad use a generic
ACPI ID of "CYPA0000" to describe it.
In order to support the proper scoping of the touchpad device under
the appropriate I2C controller device the mainboard.asl file needs
to be included after pch.asl so the I2C device exists.
Change-Id: I81e053d27be478f3a19b6f9b13cd2b4fabcb88c0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/5194
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I2ecfd9733b65b6160bc2232d22db7b16692a847f
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5149
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: I42c77d03b6a5f8ef88f1276de543bb3fc55467af
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4755
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Number one reason to use cbfs_get_file was to get file length.
With previous patch no more need for this.
Change-Id: I330dda914d800c991757c5967b11963276ba9e00
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4674
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
The main purpose of option rom is to supply int* handlers.
But supplying those is outside of coreboot scope and if someone needs those
they should run SeaBIOS anyway which runs the option roms wonderfully.
Running VGA oprom is kept because they're needed to init graphics.
This patch still keeps the options to include the option roms to make them
available to SeaBIOS.
Change-Id: I646334cf88094d3bf8f527779a68a07e0b4b93ec
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4545
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Kevin O'Connor <kevin@koconnor.net>
|
|
Clean up superfluous line terminators.
Change-Id: If837b4f1b3e7702cbb09ba12f53ed788a8f31386
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/4562
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The SMI handler code was setting S3 wake events when going
into S5 and enabling a key press to wake the system.
Change-Id: I6413ef1341e0149187df9f4f7e0c314d4c9e9c6e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65323
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4459
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Boot on falco and look in /sys/firmware/log for
the string "PCIe Root Port 1 ASPM is enabled"
Change-Id: Ie2111e4bb70411aa697dc63c0c11f13fbe66c8d8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65315
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4454
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
CLKOUT for PCIE ports 1-5 and CLKOUT_XDP are not used
and can be disabled.
I couldn't test this directly without a scope so instead I
used a modified commit that also disabled PCIe Port 0 and
saw that that correctly disabled the WLAN port.
Change-Id: I0f996e90f0ae42780de3a0c8dc5db00ec600748b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65251
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4451
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
When the EC requests the host to throttle (for charging or thermal
related reasons) the package power consumption will be limited.
Right now this is set at 12W but that is somewhat arbitrary and may
need tuning.
1) define the THRT method in \_TZ scope for EC to call
2) enable SCI events for throttle start and stop
3) define the power limit at 12W and set it in NVS
1) Enable CONFIG_ACPI_DEBUG=y in the kernel
2) Enable the Debug object event in acpi module
acpi.debug_layer=0x7f acpi.debug_level=0x2f
3) Using EC console generate host event for throttle start
> hostevent set 0x20000
4) Check dmesg for throttle start events
ACPI: Execute Method [\_SB_.PCI0.LPCB.EC0_._Q12] (Node ffff8801002c5988)
[ACPI Debug] String [0x12] "EC: THROTTLE START"
[ACPI Debug] String [0x10] "Enable PL1 Limit"
5) Using EC console generate host event for throttle stop
> hostevent set 0x40000
6) Check dmesg for throttle stop events
ACPI: Execute Method [\_SB_.PCI0.LPCB.EC0_._Q13] (Node ffff8801002c59b0)
[ACPI Debug] String [0x11] "EC: THROTTLE STOP"
[ACPI Debug] String [0x11] "Disable PL1 Limit"
Change-Id: I39b53a5e8abc2892846bcd214a333fe204c6da9b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63989
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4416
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Try to prevent WWAN from causing spurious wakes.
Change-Id: Ifcc44063de0eb1634cab9dd244737071568e3455
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63987
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4414
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Now that the rtd2132 device has the full settings the
panel timings need to be implemented. Sadly, the Tx timings
in the rtd2132 aren't 1:1 with the panel's Tx timings. Below
is the table equivalent:
RTD2132 | Falco Panel
--------+------------
T1 | T2
--------+------------
T2 | T8+T10+T12
--------+------------
T3 | T14
--------+------------
T4 | T15
--------+------------
T5 | T9+T11+T13
--------+------------
T6 | T3
--------+------------
T7 | T4
--------+------------
Change-Id: I10a3ad475d6b9485a707eb49e31afd197fc8d24d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65858
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4472
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Turn on the pei_data flag that will instruct the reference code
binary to route all USB ports to the XHCI controller on resume and
disable the EHCI controller(s).
Change-Id: I2f2ed853a6d17f90ea524bc516f3e78079222739
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63798
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4404
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
SATA is routed to PIRQG which should be interrupt 22
and not interrupt 21. The kernel uses MSI with this
device so this is only seen when booting with pci=nomsi
Change-Id: Ic90ca2c561fc4c53ec1d395c05872222c65ff98a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63796
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4398
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Since these boards do not support C10 we should not bother
advertising that state in the ACPI _CST.
Instead use this map:
ACPI(C1) = MWAIT(C1E)
ACPI(C2) = MWAIT(C3)
ACPI(C3) = MWAIT(C7S)
Change-Id: I37eb02bf9555c74e957316a1ba9778eb2b6ee128
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62898
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4377
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The EC temperature sensors were renumbered and now PECI
is at index 0.
1) boot on falco
2) check /sys/class/thermal/thermal_zone0/temp
3) check 'temps' on ec console
Change-Id: Idde1457c42c80850b5b8ac22781060ed9b224d13
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61896
Reviewed-on: http://review.coreboot.org/4367
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
This may need further tuning but will start at 1.0%.
boot on falco and check /sys/firmware/log
localhost ~ # grep RTD2132 /sys/firmware/log
RTD2132: Enable 1.0% Spread Spectrum
I2C: 01:35 (Realtek RTD2132 LVDS Bridge)
Change-Id: I96e1c14dbc6a7bfaf1c8deb1806c48bf2fd3e32a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61895
Reviewed-on: http://review.coreboot.org/4366
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
The SystemAgent contains a mini-hd audio controller at PCI 0:3.0
which uses the same verb table init sequence as the southbridge.
In order to avoid two copies of the verb table loading code I
separated out the HDA verb table functions into a file that can
be re-used and then added a minihd driver to the haswell northbridge.
The minihd verb table is the same across devices so it can live
within the minihd driver rather than needing to be specified in
each separate mainboard.
I also fixed up the driver for lynxpoint HDA by following the
reference code.
Without HDMI cable plugged in driver does not find any codec,
and it does not seem to re-probe when HDMI is connected. We may
be missing kernel patches for this.
hda-intel 0000:00:03.0: no codecs found!
With a basic kernel patch to add 0x0a0c device ID to HDA driver
and with HDMI cable connected it is much happier:
snd_hda_intel 0000:00:03.0: irq 60 for MSI/MSI-X
input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input9
snd_hda_intel 0000:00:1b.0: irq 61 for MSI/MSI-X
input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input10
input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input11
Change-Id: Ifa587984be4fc2801704a0368b9cdf8379c2450e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59336
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4318
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The drivers are designed to work with an edge triggered interrupt.
Change-Id: I35a121ecfb6409bb9049f4d1e034185bb3bb7557
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61664
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4360
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
When the board is in S3 and S5 the WLAN_DISABLE_L signal
can leak power into the WLAN power well since the GPIO
controlling WLAN_DISABLE_L is in the suspend well. Therefore,
drive WLAN_DISABLE_L low to avoid the power leak.
Change-Id: I1a0df80dd47fdbd535aca7a9d49253794c480606
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61421
Reviewed-on: http://review.coreboot.org/4358
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
USB2 Port A set to 6.4" and Back Panel
USB2 Port B set to 5.2" and Back Panel
USB2 Port C set to 12.3" and Internal
Other devices all set to Internal.
build and boot on falco and check settings.
Based on the config settings all ports end up with
tuning param 1 == 5 and param 2 == 2
U2ECR[0] = 0x00059501
U2ECR[1] = 0x00059501
U2ECR[2] = 0x00059501
U2ECR[3] = 0x00059501
U2ECR[4] = 0x00059501
U2ECR[5] = 0x00059501
U2ECR[6] = 0x00059501
U2ECR[7] = 0x00059e01
Change-Id: I6b9e6df2679036a501355e6b389a486a6f178f99
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61297
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4350
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This CPU does not support Configurable TDP and so far does
not need to use Controllable TDP.
Change-Id: I15599cd4e6890dd5c9d9f99bc4e95307a8dcc827
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60657
Reviewed-on: http://review.coreboot.org/4347
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On some systems there may be 2GB SKU that is the same as the
4GB SKU but just one channel of memory. In that case we need
to ensure that both copies of the same SPD source end up
populated by ensuring that repeated entries are included by
using $+ instead of $^.
Alternatively we could do the check inside romstage, but it
is already set to behave this way if the SPD gets populated
correctly.
I changed spd_index to 3 in falco romstage to force it to
pretend it was a 2GB config of the same memory, then booted
to ensure it was indeed limited to 2GB.
memcfg channel[0] config (00780008):
ECC inactive
enhanced interleave mode on
rank interleave on
DIMMA 2048 MB width x16 single rank, selected
DIMMB 0 MB width x16 single rank
memcfg channel[1] config (00600000):
ECC inactive
enhanced interleave mode on
rank interleave on
DIMMA 0 MB width x8 single rank, selected
DIMMB 0 MB width x8 single rank
Change-Id: Ibfe5051ccda2fe69e8caff3f3c264116e3411c65
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59483
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Jay Kim <yongjaek@chromium.org>
Reviewed-on: http://review.coreboot.org/4319
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The OIPG package needs to have >1 member to make the chromeos_acpi
kernel driver do the right automagic sysfs topology creation.
Additionally an "unimplemented" GPIO should be reported as 0xFF
because 0 is a valid GPIO number.
verify crossystem on slippy
$ sudo crossystem | grep -e recoverysw_cur -e wpsw_cur
recoverysw_cur = (error)
wpsw_cur = 1
Change-Id: I06dff09152bde30a3ffe58b1defe9d299155472c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57471
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4221
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This config option was not enabled which was preventing
the user from enabling developer mode from recovery mode.
With this enabled we can disable the "dev mode by default"
behavior and let people enable it by entering recovery mode.
This will make the firmware behave like a typical chromeos
device.
Peppy is left in "default dev mode" until after bringup.
1) boot slippy in normal mode by default
2) enter recovery mode with servo button
3) Ctrl+D on USB keyboard to enter developer mode
4) boot slippy in developer mode
Change-Id: I414c0d10dd0489e3c89798f75a2872a43297c8d8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57350
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4220
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Those building Chromebook firmware from coreboot git might be more
interested in building without ChromeOS extras.
Change-Id: I2f176d059fd45bf4eb02cc0f3f1dcc353095d0ce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3977
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
- Add a new USB location field
- Add a new "ddr_refresh_2x" field, enabled on Falco only
- Fix copy+paste bug in baskingridge
Checked that tREFI is halved during memory setup in the memory
training log:
tREFImin = 6240 << DEFAULT
C(0).tREFI = 0xc30 << MODIFIED (=3120)
C(0).tREFI = 0xc30 << MODIFIED (=3120)
Also ensure that the SD card is detected properly again.
Change-Id: Ie3a82c08df06ada9af56282b5255caefa56487f2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57349
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4219
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
These are based on the datasheet and I included the timing
values I used from the docs.
Change-Id: Ib75b2c5e50ac09d1e4cf9dd22229bb0f0a8965a4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58540
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4234
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Set nid 0x12 instead of nid 0x05. The DMIC is on NIC 0x12.
Change-Id: Ifc883b65a50aeec6a6d3ad02fe8418f124e6241d
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58711
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Jay Kim <yongjaek@chromium.org>
Tested-by: Jay Kim <yongjaek@chromium.org>
Reviewed-on: http://review.coreboot.org/4246
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
SPD GPIOs were being read prior to initialization in romstage_common. To
fix, pass the copy_spd function to romstage_common, to be called at the
appropriate time (after PCH init, before DRAM init).
Change-Id: I2554813e56a58c8c81456f1a53cc8ce9c2030a73
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58608
Reviewed-on: http://review.coreboot.org/4237
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The wake device input pins are active low and the
GPIOs need to be set as inverted when they are marked
as an input so they are not spuriously logged.
suspend/resume on slippy with trackpad wake:
8 | 2013-05-29 07:43:14 | ACPI Enter | S3
9 | 2013-05-29 07:43:18 | ACPI Wake | S3
10 | 2013-05-29 07:43:18 | Wake Source | GPIO | 12
and with power button wake:
11 | 2013-05-29 07:43:35 | ACPI Enter | S3
12 | 2013-05-29 07:43:40 | EC Event | Power Button
13 | 2013-05-29 07:43:40 | ACPI Wake | S3
14 | 2013-05-29 07:43:40 | Wake Source | Power Button | 0
Change-Id: I15d38dcc9b2fb4b2b0eb27da358fa3c343e22323
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56940
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4209
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The EC was disabling flash commands and sysjump was not working
properly. With those two fixed software sync works properly.
Google Chrome EC MKBP driver ready, id 'slippy_no_version'
Clearing the recovery request.
EC hash:7fea29992ef72e3e64d8ffe522aa1dfa68dcb44a2da96a4c19530ea1a0bd22c4
EC-RW hash address, size are 0xffa1cfe8, 32.
Hash = 727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
Expected hash:727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
EC-RW firmware address, size are 0xffad000c, 57180.
VbEcSoftwareSync() - expected len = 57180
Computed hash of expected image:727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
VbEcSoftwareSync() updating EC-RW...
VbEcSoftwareSync() jumping to EC-RW
VbEcSoftwareSync() in RW; done
Change-Id: I63ca00d6c94854f2b395eb736ce20792da5f8de2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56821
Reviewed-on: http://review.coreboot.org/4208
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Set verbs to reflect the layout used for ALC283 in Falco,
which ends up being the same as Slippy.
Change-Id: I3dce4effefaa91ee5bdcbe2a8a3750ebc41376ad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58196
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4232
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
RAM_ID indices have been changed and settled on a 2GB config
that will be the same DRAM chips but only used in one channel.
Change-Id: I444e655883ae045622ab3dfb964da4d7f86e1c0d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56810
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4198
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
These are placeholder values until we can configure for
the exact panel.
Change-Id: If40367c0e5f80d46d085c89b0edae60f1ccacdaf
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56808
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4197
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add the onboard I2C devices for Falco trackpad/lightsensor
and generate SMBIOS Type41 tables for them.
Add ACPI device for the trackpad to expose the interrupt map
to the OS so it can be used.
Configure interrupt GPIOs as PIRQ type and wake GPIOs as
just standard input type. The wake GPIO is reconfigured as
ACPI SCI in the specific device _DSW method. This prevents
the wake GPIO from generating a flood of SCI at runtime.
LTE_WAKE_L_Q and WLAN_WAKE_L_Q are left as ACPI SCI as these
are not repurposed interrupt pins so they are not generated
at runtime.
SIM_DET and ALS_INT_L are set as input since we don't have an
interrupt handler for them.
Change-Id: Ibe9687b2f7f41ead18353c3f650219fe6e94ae2f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56632
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4191
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This was provided by the vendor but I added the part number at
byte 128-143 so it can be identified when extracted by mosys.
Change-Id: Ib1e430cd390b4dbc013fc0802f1a59c1a0412577
Reviewed-on: https://gerrit.chromium.org/gerrit/56634
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4192
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Update and use the new pei_data data structure. Now that the
reference code is fixed it's possible to properly disable/enable
the USB2 and USB3 ports correctly.
Change-Id: I075c646e7574be354420b6e59507e8917a97d0f0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56594
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4185
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Only the first two DIMM SPDs are specified so far
- GPIO map is updated
- iSSD power sequencing removed
- USB port map updated
Change-Id: I4172460d3b075bfd5bb22013a6225cf0e8f95b9c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56329
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4184
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|