Age | Commit message (Collapse) | Author |
|
Currently when enabling Deep S3 or Deep S5 it unconditionally gets enabled
in both DC and AC states. However since using Deep S3 disables some
expected features like wake-on-USB it is not always desired to enable the
same state in both modes.
To address this split the setting and add a separate config for Deep Sx in
AC and DC states.
All motherboards that set this config were updated, but there is no actual
change in behavior in this commit.
BUG=b:36723679
BRANCH=none
TEST=This commit has no runtime visible changes, I verified on Eve that the
Deep SX config registers are unchanged, and it compiles for all affected boards.
Change-Id: I590f145847785b5a7687f235304e988888fcea8a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19239
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Due to issues with stability limit the SKU with K4EBE304EB-EGCF
memory to 1600MHz instead of 1866MHz.
BUG=b:37172778
BRANCH=none
TEST=pass stress testing on devices with this memory
Change-Id: I02af7e9c35e2c5b0b85223d58025cbd29841d973
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19227
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update the I2C rise/fall timings based on newly measured values
on a new board with updated pull-up resistor values.
Touchscreen: rise time 98ns, fall time 38ms
Touchpad: rise time 111ns, fall time 41ns
TPM: rise time 112ns, fall time 34ns
BUG=b:35583133
BRANCH=none
TEST=Each I2C bus frequency was verified on a scope to be ~400MHz
Change-Id: Ibb3a15fa0cc862f36c1b9c63ac7847221020c4c0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19202
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch attempts to finish the separation between CONFIG_VBOOT and
CONFIG_CHROMEOS by moving the remaining options and code (including
image generation code for things like FWID and GBB flags, which are
intrinsic to vboot itself) from src/vendorcode/google/chromeos to
src/vboot. Also taking this opportunity to namespace all VBOOT Kconfig
options, and clean up menuconfig visibility for them (i.e. some options
were visible even though they were tied to the hardware while others
were invisible even though it might make sense to change them).
CQ-DEPEND=CL:459088
Change-Id: I3e2e31150ebf5a96b6fe507ebeb53a41ecf88122
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18984
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The virtualized developer switch was invented five years ago and has
been used on every vboot system ever since. We shouldn't need to specify
it again and again for every new board. This patch flips the Kconfig
logic around and replaces CONFIG_VIRTUAL_DEV_SWITCH with
CONFIG_PHYSICAL_DEV_SWITCH, so that only a few ancient boards need to
set it and it fits better with CONFIG_PHYSICAL_REC_SWITCH. (Also set the
latter for Lumpy which seems to have been omitted incorrectly, and hide
it from menuconfig since it's a hardware parameter that shouldn't be
configurable.)
Since almost all our developer switches are virtual, it doesn't make
sense for every board to pass a non-existent or non-functional developer
mode switch in the coreboot tables, so let's get rid of that. It's also
dangerously confusing for many boards to define a get_developer_mode()
function that reads an actual pin (often from a debug header) which will
not be honored by coreboot because CONFIG_PHYSICAL_DEV_SWITCH isn't set.
Therefore, this patch removes all those non-functional instances of that
function. In the future, either the board has a physical dev switch and
must define it, or it doesn't and must not.
In a similar sense (and since I'm touching so many board configs
anyway), it's annoying that we have to keep selecting EC_SOFTWARE_SYNC.
Instead, it should just be assumed by default whenever a Chrome EC is
present in the system. This way, it can also still be overridden by
menuconfig.
CQ-DEPEND=CL:459701
Change-Id: If9cbaa7df530580a97f00ef238e3d9a8a86a4a7f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18980
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The kernel driver for rt5663 expects to get an interrupt on both
a rising and falling edge, and using a legacy interrupt doesn't
provide that flexibility.
Instead configure this pin as a GPIO and use the interrupt through
the GPIO controller. This allows using GpioInt() with ActiveBoth
setting and results in correct operation of the headset jack.
BUG=b:35585307
BRANCH=none
TEST=test on Eve that headset jack detect is read properly at
boot, and that plugging in and removing both generate a single
interrupt event in the driver.
Change-Id: I6f181ec560fe9d34efc023ef6e78e33cb0b4c529
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18836
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Keep the BOOT0 pin triggering the MCU bootloader as an input,
so the Servo debug board doesn't have to fight with the PCH to program
it, the net already has an external pull-down to ensure that the MCU is
in normal mode at boot.
By default, do not drive the FP sensor reset from the PCH, the MCU is
now managing the reset line (but the PCH still has a connection on the
current boards).
BRANCH=none
BUG=b:36025702
TEST=manual testing, program the MCU through a Servo v2 board, and use
the FP sensor through the MCU and verify it is not stuck under reset.
Change-Id: I19113b5d78013d0ab6ec5a72c6f71dd4c67a88e8
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/18830
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Set the AC and DC loadline values based on the KBL-Y 2+2 defaults
that are applied by FSP. These will be tuned later and are exposed
as defaults so the engineers know what to start with.
BUG=b:36228330
BRANCH=none
TEST=Build and boot on Eve and check debug FSP output to ensure that
it is applying the provided loadline values
Change-Id: Ieae4f2b201d8210e75bdb9438070a3a2e1fda6b7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18820
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
With the move to FSP 2.0 the number of VR types supported was
reduced to 4, and the VR_RING type is no longer present.
This means all existing boards using FSP 2.0 are incorrectly
passing VR configuration into FSP as the values corresponding to
"GT Sliced" and "GT Unsliced" have changed.
Fix this by updating the skylake SOC VR handling to account for
changes in the FSP configuration and no longer provide VR_RING
type when using FSP 2.0.
BUG=b:36228330
BRANCH=none
TEST=manual: build and boot on Eve
Change-Id: I59eea9fba006a4c235d7b42d07fdc6e4f44f7351
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18818
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
On this platform the DMICs are connected to the rt5514 DSP instead
of directly connected to the SOC. Use the new rt5514 NHLT blob
instead of the 4ch DMIC blob and add the required I2C and SPI
entries in devicetree so this can get probed properly.
BUG=b:35585307
BRANCH=none
TEST=build and boot on Eve P1 and check for rt5514 driver enumerated
by the kernel
Change-Id: I0f2cb532771ee1857df7f33c52a96acf96dc1f54
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18817
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
A new board revision is making use of two previously unused GPIOs
to drive BOOT/RESET pins to an on-board MCU.
The reset pin is open drain so it is set as input by default, and
the boot pin is driven low by default.
Since these are UART0 pins they also need to be set up again after
executing FSP-S as it will change them back to native mode pins.
BUG=b:36025702
BRANCH=none
TEST=manual testing on reworked board, toggling GPIOs to put
the MCU into programming mode.
Change-Id: Id6f0ef2f863bc1e873b58e344446038786b59d25
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18661
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Apply tuning for the PCH I2C buses on Eve based on rise/fall time
measurements that were done with a scope.
BUG=chrome-os-partner:59686
BRANCH=none
TEST=Manual testing on Eve P1 to verify that all devices on I2C
buses are still functional. Post-tuning measurement will be done
once a new firmware is released.
Change-Id: I3d70ff455a20ecda374d7e7fa6cd3ab15e7f2621
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18487
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This is done to avoid any conflicts with same IRQ enums defined by other
drivers.
BUG=None
BRANCH=None
TEST=Compiles successfully
Change-Id: I539831d853286ca45f6c36c3812a6fa9602df24c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18444
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Wacom I2C driver does the same thing as I2C HID driver, other than
defining macros for Wacom HID. Instead of maintaining two separate
drivers providing the same functionality, update all wacom devices to
use generic I2C HID driver.
BUG=None
BRANCH=None
TEST=Verified that ACPI nodes for wacom devices are unchanged.
Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18401
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable Fast-Plus speed for the touchscreen device so it can
be used at 1MHz instead of 400KHz.
BUG=chrome-os-partner:61277
TEST=manual testing on Eve P1, needs backported kernel patches
to actually make use of any I2C speed other than 400KHz
Change-Id: I3f44ff4a02a02a7b05e69ad54d4c6d60e5878393
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18397
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add the audio devices to Eve mainboard:
- Describe Maxim 98927 speaker amps and RT5663 headphone codec
in ACPI so they can be enumerated by the OS.
- Supply NHLT binaries for MAX98927, RT5663, and DMIC_4CH.
BUG=chrome-os-partner:61009
TEST=manual testing on Eve P1 with updated kernel to ensure that
both speakers and headset are functional. DMIC support is
is still being worked on and is not yet functional.
Change-Id: I5243e35d159a0ed15c6004e94ba5a50b28cff0a9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18398
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
Change config option selection from "config xyz default y" to "select
xyz" if the config option has no dependencies.
BUG=None
BRANCH=None
TEST=Verified that config option selection remains unchanged.
Change-Id: I259ae40623b7f4d5589e2caa0988419ba4fefda4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18400
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Apply the measured rise and fall times for I2C bus 1 on Eve
so it can be tuned properly for 400KHz operation.
BUG=chrome-os-partner:63020
TEST=verify I2C1 bus speed with a scope
Change-Id: I32b5aa460ea35aadca7f3d52324a64880764919f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18396
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Currently UART0 GPIOs are being put into native mode during FSP-S
stage, so have ramstage re-configure them back to regular GPIO mode.
GPP_C8 does not seem to be functioning properly when routed to the
APIC, possibly due to the UART0 being enabled even though it is unused,
which is required because UART0 is PCI 1e.0 and so must be present for
other 1e.x functions to be enumerated. Instead, use this pin as a GPIO
interrupt so it will be routed through the GPIO controller at IRQ 14.
GPP_C9 was inverted and was only working because the pin was being
re-configured in FSP-S.
Also export the reset gpio as a device property so it can be used by
the kernel driver, which will stop it from complaining at boot.
BUG=chrome-os-partner:61233
TEST=verify that the interrupt and device is functional in the OS
Change-Id: Iaf9efbf50a13a981c6a9bbd507475777837e9c12
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18395
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
eve is based on Kabylake SoC hence select the appropriate
config.
Change-Id: I756dda5a1924e83a02ac1cebb1907884f436a13f
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18314
Tested-by: build bot (Jenkins)
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use the newly added SPI SSDT generator for adding FPC device.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully. Verified that the SSDT entry matches the
entry in mainboard.asl
Change-Id: I1b3c33f2b4337735a9725dd4eb6193b2455962d7
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18343
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Change touchpad HID to use with the Google Centroiding Touchpad driver.
BUG=chrome-os-partner:61088
TEST=`emerge-eve coreboot`
Change-Id: I199ff46f1a93d3eccc8c694742585dcf37b2373f
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://review.coreboot.org/18359
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Eve is a convertible add support for sending Tablet mode switch
changes from EC to AP.
Change-Id: I35133ebc1439852d0ceb88d7d679b37356b0869d
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/18276
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The WAK_STS bit is not set in a wake from G3, so the check for this
bit needs to only be done when checking for a wake from S3.
This change correctly enables the keyboard backlight in wake from G3
and only does not enable it during a wake from S3.
BUG=chrome-os-partner:58666
TEST=Use Refresh+Power to issue hard reset and ensure that the keyboard
backlight turns on like it does when waking from S5. Also force enter
hibernate with Alt+VolumeUp+H and then power back up and ensure that
the keyboard backlight is enabled when booting.
Change-Id: I44045950e38aa5e5ae96a79385d604791852c7e6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18280
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change fixes the two sets of pins that were swapped in the
map of DQS signals from CPU to DRAM for channel 1.
Although this does not appear to have any impact to the system it
does result in different register values for DQS pin mapping that
are programmed inside FSP.
BUG=chrome-os-partner:58666
TEST=This fix was verified against the current schematic and using
FSP debug output.
Change-Id: I45b821071ba287493b3b13204b7f5b38e06eee75
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18279
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals
when doing GPIO-driven I2S. This needs to be high by default so
the DSP can drive these signals, instead of low where it is enabled
for GPIO-driven I2S and the DSP cannot drive these signals.
BUG=chrome-os-partner:58666
TEST=play test sound in OS over internal speaker
Change-Id: I49935e659bf67225d3f5db1b06acc2cd046dcd74
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18281
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In order for PD charge events to properly notify the OS when a charger is
attached we need to enable the PD MCU device and event source from the EC.
Without this change the charging still happens, but the OS does not notice
and update the charge state icon in the Chrome OS UI.
BUG=chrome-os-partner:62206
BRANCH=none
TEST=plug in a charger to either port and see charge status updated to
indicate charging in the power_supply_info tool and the Chrome OS UI.
Change-Id: Ia6f63ac719b739326d313f657a68005c32f45b8d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18209
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The devicetree settings were incorrect in a few places with
respect to the SOC and board design:
- IMVP8 VR workaround is for MP2939 and not MP2949 on Eve
- IccMax values are incorrect according to KBL-Y EDS
- USB2[6] is incorrectly labeled
- I2C touch devices do not need probed as they are not optional
- PCIe Root Port 5 should be enabled
- I2C5 device should not be enabled as it is unused
BUG=chrome-os-partner:58666
TEST=manually tested on Eve board
Change-Id: I74e092444ead4b40c6d8091b80a691d44e2c6c7d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18200
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In order to get quick boot speeds into recovery enable the
feature that allows for a separate recovery MRC cache.
This requires shuffling the FMAP around a bit in order to
provide another region for the recovery MRC cache. To make
that shuffling easier, group the RW components into another
sub-region so it can use relative addresses.
BUG=chrome-os-partner:58666
TEST=manual testing on eve: check that recovery uses the MRC
cache, and that normal mode does too. Check that if cache is
retrained in recovery mode it is also retrained in normal mode.
Also check that events show up in the log when retrain happens.
Change-Id: I6a9507eb0b919b3af2752e2499904cc62509c06a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18199
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable the keyboard backlight as early in boot as possible to
provide a indication that the BIOS is executing.
Since this is bootblock it can't use the convenience function
for checking for S3 resume so just read the PM1 value from the
SOC and check it directly.
Use a value of 75% for the current system as that is visible
without being full brightness.
BUG=chrome-os-partner:61464
TEST=boot on eve and check that keyboard backlight is enabled
as soon as the SOC starts booting
Change-Id: I9ac78e9c3913a2776943088f35142afe3ffef056
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18197
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
- Remove the 0mA entry for the charger performance table
- Slightly raise the passive limit for TSR2/TSR3 to 55C
BUG=chrome-os-partner:58666
TEST=manual testing on P1 system
Change-Id: I75c66afe04afbbdb64a45833eb938e57ff21b392
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18172
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable the ACPI interface to EC driven keyboard backlight.
BUG=chrome-os-partner:61464
TEST=manual testing on P1 system
Change-Id: I13d96c13d7db726b1e8289131db65104bd302efe
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18171
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable an internal pull-up on ACPRESENT signal.
BUG=chrome-os-partner:58666
TEST=manual testing on P1
Change-Id: I0bb86f4547272e021ffd10998faa0e2f103b0808
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18170
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Enable an internal pull-up on the power button input as a quick
press is resulting in power button override being asserted.
BUG=chrome-os-partner:61312
TEST=tested on eve P0b to ensure quick power button press does
not result in a shutdown due to power button override.
Change-Id: I3028cf7faef309cf4d60c3585b48adab6e1549d4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17962
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
GPP_D12 needs an internal pull-up to get this rail working on
current boards. GPP_D0-GPP_D3 were changed from SPI interface
and I just missed this change earlier.
BUG=chrome-os-partner:58666
TEST=test camera and touchpad on eve
Change-Id: Idfa186f2930afbe5651f4e0fc11a19cd0dd4295f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17922
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Set the thermal throttle (prochot) activation to be 10 degrees
below TJmax so PROCHOT# kicks in at 90C instead of 100C.
BUG=chrome-os-partner:58666
TEST=boot on eve, check msr value before and after resume:
> iotools rdmsr 1 0x1a2
0x000000000a6400e6
> echo mem > /sys/power/state
> iotools rdmsr 1 0x1a2
0x000000000a6400e6
Change-Id: I3ab3a050a1e27c18a940bd7519eabaf015ef93eb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17901
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable the actual touch devices to be probed by the kernel
and remove the placeholder devices that I put in before
and were used for initial bringup.
BUG=chrome-os-partner:58666
TEST=tested on eve
Change-Id: I7fc6f9da83b1abbae6dd069f759b220d59153d1c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17896
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Put the UART pins into native mode in bootblock so they are not
floating when we try to communicate with H1 over I2C. Without
a serial console enabled BIOS these pins were not configured
until ramstage.
BUG=chrome-os-partner:60935
TEST=Boot Eve board without serial console and H1 TPM enabled
Change-Id: I30f3bf0bacc1bbd776b351a9c09748b0601c39bc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17893
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
On this board i2c3 bus is connected to the display TCON, but it is
acting as the master when it has power so it can read from its own
EEPROM on the bus. In order to prevent any possible issues in S0
make these pins input on the SOC.
BUG=chrome-os-partner:58666
TEST=tested on eve board, but this bus was not used before so
there is no visible change in behavior.
Change-Id: Ide32f45ee33ca986fd3249a5161e01edf99d6e22
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17800
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
There is ongoing work to link SPI bus and devices in to the devicetree
so this can be generated, but for now put in the raw ASL code to
describe this controller so it can be used by the factory.
BUG=chrome-os-partner:55538
TEST=successfully load fpc1020 kernel module on eve board
Change-Id: I6641664e60fcf2c0bad4b3506c77513b26d7be2e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17776
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
These headers & comments indicating a lack of functionality don't help
anything. We discourage copyrights and licenses on empty files, so
just clear these.
Change-Id: Id2ab060a2726cac6ab047d49a6e6b153f52ffe6d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17657
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Program USB Overcurrent pins as per board schematics definition.
BUG=none
BRANCH=none
TEST=Build and boot kunimitsu from USB device.
Change-Id: I6aeb65953c753e09ad639469de7d866a54f42f11
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/17570
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Make MMCONF_SUPPORT selected with MMCONF_SUPPORT_DEFAULT.
Platforms that remain to have explicit MMCONF_SUPPORT are
ones that should be converted.
Change-Id: Iba8824f46842607fb1508aa7d057f8cbf1cd6397
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17527
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Instead of defining the same functions for reading/clearing boot-mode
switches from EC in every mainboard, add a common infrastructure to
enable common functions for handling boot-mode switches if
GOOGLE_CHROMEEC is being used.
Only boards that were not moved to this new infrastructure are those
that do not use GOOGLE_CHROMEEC or which rely on some mainboard specific
mechanism for reading boot-mode switches.
BUG=None
BRANCH=None
TEST=abuild compiles all boards successfully with and without ChromeOS
option.
Change-Id: I267aadea9e616464563df04b51a668b877f0d578
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17449
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add the DIMM SPD data for memory types that are not used yet
but are on the matrix and may be used in future builds.
Also fix a typo in the part number string for one type.
BUG=chrome-os-partner:58666
TEST=build and boot on eve p0
Change-Id: I20401d7afb69f1c3ae1a3b0d6e3ec9097f54ef96
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17437
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In preparation of merging the lpss i2c config structures on
apollolake and skylake move the i2c voltage variable to its
own field. It makes refactoring things easier, and then there's
no reason for a separate SoC specific i2c config structure.
BUG=chrome-os-partner:58889
Change-Id: Ibcc3cba9bac3b5779351b673bc0cc7671d127f24
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17347
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add the eve board files using kabylake and FSP 2.0.
BUG=chrome-os-partner:58666
TEST=build and boot on eve board
Change-Id: I7ca71fe052608d710ee65d078df7af7b55d382bc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17177
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|