| Age | Commit message (Collapse) | Author |
|---|
|
Update Power Limit2 (PL2) minimum value to the same as maximum value
for magolor board. DTT does not throttle PL2, so this minimum value
change here does not impact any existing behavior on the system.
BUG=b:168353037
BRANCH=None
TEST=Build and test on magolor board
Change-Id: I74e960de506d366cba2c8aefb23f9e69337fd163
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
LTE module used in boten has a specific power on/off sequence.
GPIOs related to power sequnce are:
* GPP_A10 - LTE_PWR_OFF_R_ODL
* GPP_H17 - LTE_RESET_R_ODL
1. Power on: GPP_A10 -> 20ms -> GPP_H17
2. Power off: GPP_H17 -> 10ms -> GPP_A10
3. Warm reset: Power off -> 500ms -> Power on
Configure the GPIOs based on these requirements.
BUG=b:163100335
TEST=Build and boot Boten to OS. Ensure that the LTE module power
sequence requirements are met.
Change-Id: Ic6d5d21ce5267f147b332a4c9b01a29b3b8ccfb8
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peichao Wang <pwang12@lenovo.corp-partner.google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This support is required to power off certain components that exist only
in certain variants.
BUG=None
TEST=Build and boot Boten to OS.
Change-Id: Ib43ada784666919a4d26246a683dad7f3546fabb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peichao Wang <pwang12@lenovo.corp-partner.google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
EEPROM in the camera module does not require any specific power
resources. This will ensure that no unnecessary resources are turned on
while accessing the camera EEPROM.
BUG=b:167938257
TEST=Build and boot to OS in Drawlat. Ensure that the camera EEPROM is
listed in the output of i2cdetect.
Change-Id: Iece9b3f657bf94a21cc08bf1745353575858f9b2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Handle AC connect and disconnect notifications from Embedded Controller
(EC) and wake from S3/S0ix.
BUG=b:172266344
TEST=Build and Boot to OS in Drawlat. Ensure that the system wakes up
from suspend on AC connect and disconnect on both the TypeC ports.
276 | 2020-11-04 12:21:29 | S0ix Enter
277 | 2020-11-04 12:21:40 | S0ix Exit
278 | 2020-11-04 12:21:40 | EC Event | AC Disconnected
279 | 2020-11-04 12:21:57 | S0ix Enter
280 | 2020-11-04 12:22:03 | S0ix Exit
281 | 2020-11-04 12:22:03 | EC Event | AC Connected
282 | 2020-11-04 12:22:35 | S0ix Enter
283 | 2020-11-04 12:22:47 | S0ix Exit
284 | 2020-11-04 12:22:47 | EC Event | AC Disconnected
285 | 2020-11-04 12:23:08 | S0ix Enter
286 | 2020-11-04 12:23:16 | S0ix Exit
287 | 2020-11-04 12:23:16 | EC Event | AC Connected
Change-Id: I7fa4ac0096548fd63af86e9f56c4c1ee25491399
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update Power Limit2 (PL2) minimum value to the same as maximum value for
dedede variants (baseboard and drawcia). Currently, variants like boten,
waddledee, waddledoo, metaknight and wheelie uses the DTT entries from
baseboard devicetree since there is no override present for these variants.
So, these variants will also reflect this change of PL1 minimum value.
For madoo variant, PL2 minimum value already set the same as PL2 maximum
value. DTT does not throttle PL2, so this minimum value change here does not
impact any existing behavior on the system.
BUG=None
BRANCH=None
TEST=Build and test on drawcia system
Change-Id: I7ecf1ffcc7871192ebe18eb8c3c3fd3e1193721e
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47154
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory part being added is:
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNBKMMLXR-NEE
MT53E1G32D2NP-046 WT:A
K4UBE3D4AA-MGCR
BUG=b:169813211
TEST=Build the metaknight board.
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Change-Id: I0d0d22f4790f66b5265803e4dcf01234a16b1993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change reorganizes the CNVi device entries in mainboard
devicetree/overridetree and SoC chipset tree to make it consistent
with how other SoC internal PCI devices are represented i.e. without a
chip driver around the SoC controller itself.
Before:
chip drivers/wifi/generic
register "wake" = "..."
device pci xx.y on end
end
After:
device pci xx.y on
chip drivers/wifi/generic
register "wake" = "..."
device generic 0 on end
end
end
Change-Id: I22660047a3afd5994400341de0ca461bbc0634e2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
We all knew this was coming, 32 bits is never enough. Doing this early
so that it doesn't affect too much code yet. Take care of every usage of
fw_config throughout the codebase so the conversion is all done at once.
BUG=b:169668368
TEST=Hacked up this code to OR 0x1_000_0000 with CBI-sourced FW_CONFIG
and verify the console print contained that bit.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6f2065d347eafa0ef7b346caeabdc3b626402092
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45939
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:168783630
TEST=Measured the I2C bus frequency reduce to 387 KHz.
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I9f5b81815f86db7bdcea95a95b9c9b235b4a34b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46613
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 214c719eed83967b8f0564feca65eebb3d83f5bc.
CB:45857 overrides the GPIO PM configuration if Cr50 does not support
long interrupt pulse width. More recent Cr50 Firmware versions support
long pulse width and hence the GPIO PM can take the default
configuration.
BUG=None
TEST=Build and boot Drawlat to OS. Ensured that 200 iterations of
suspend/resume sequence, warm and cold reboot cycles each are
successful.
Change-Id: I8e3be42cd82fd3ae919d23d6f19c84a90b9c737a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46652
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
The dt option `speed_shift_enable` is obsolete now. Drop it.
Change-Id: I5ac3b8efe37aedd442962234478fcdce675bf105
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
RW_LEGACY region needs to be 1 MiB to accommodate any alternate
firmware. Hence update the flash ROM layout as below:
* Grab ~512 KiB from each FW_MAIN_A/B regions and allocate them to
RW_LEGACY region so that it grows to 1 MiB.
* Remove VBLOCK_DEV region which is not used.
* Re-size the ELOG region to 4 KiB since that is the maximum size of the
ELOG mirror buffer.
* Resize RW_NVRAM, VBLOCK_A/B regions to 8 KiB since no more than that
size is used in those regions.
* Resize SHARED_DATA region to 4 KiB since no more than that size is
used in that region.
* Based on the resizing, allocate each FW_MAIN_A/B regions with 72 KiB.
BUG=b:167943992, b:167498108
TEST=Build and boot to OS in Drawlat. Ensure that the firmware test
setup and flash map test are successful. Ensure that the event logs are
synced properly between reboots. Ensure that the suspend/resume sequence
is working fine. Ensure that the ChromeOS firmware update completes
successfully for the boot image with updated flash map and the system
boots fine after the update.
Change-Id: I53ada5ac3bd73bea50f4dd4dd352556f1eda7838
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46569
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To support mipi WFC.
1. enable DRIVERS_INTEL_MIPI_CAMERA/SOC_INTEL_COMMON_BLOCK_IPU
2. add IPU/VCM/NVM/CAM1 in devicetree
BUG=b:163879470, b:171258890, b:170936728, b:167938257
TEST=Build and boot to OS. Capture frames using camera app.
Change-Id: I96f2ef682dff851d7788c2b612765a92228ddf75
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44939
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the metaknight variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:169813211
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_METAKNIGHT
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Change-Id: Ia2e473eb1d0a2c819b874e497de0823fca75645a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Early JSL silicon hang while booting Linux with ISST enabled. The
malfunctioning silicon revisions have been used only for development
purposes and have been phased out. Thus, drop the ISST workaround.
Change-Id: Ic335c0bf03a5b07130f79c24107a1b1b0ae75611
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Update PL1 max and min power values
BUG=None
BRANCH=None
TEST=build and verify on dralat system
Change-Id: I75d47fa721576564f71fbd5d5fd2e820fc3f1925
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add devicetree and device ID for P-sensor
BUG=b:161217096
BRANCH=NONE
TEST=We can get the data from P-sensor if touch the SAR antenna.
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: I70f303995b106cca9758b36ebcde112ebcc90950
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update devicetree of boten that enable stylus
BUG=b:160752604
BRANCH=NONE
TEST=build bios and verify function for boten
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: Ifbcac18fcf758f3d870a6af0d1b03e34369414c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The camera sensor component chosen for UFC and WFC have an address
conflict. Resolve it by enabling GPIO based I2C Multiplexer. Also
configure the GPIO that is used as select line.
BUG=b:169444894
TEST=Build and boot waddledee to OS. Ensure that the ACPI identifiers
are added for I2C devices multiplexed using I2C MUX under the
appropriate scope.
Change-Id: I9b09e063b4377587019ade9e6e194f4aadcdd312
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add tcc, critical, passive policy, and pl values from thermal team.
BUG=b:169215576
TEST=build and verify by thermal tool
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I4f61eaa7eab2b86b04ff0541886621afb3082b1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Change-Id: I5a5f4e7067948c5cc7a715a08f7a5a3e9b391191
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This change switches all mainboard devices to use drivers/wifi/generic
instead of drivers/intel/wifi chip driver for Intel WiFi
devices. There is no need for two separate chip drivers in coreboot to
handle Intel and non-Intel WiFi devices since the differences can be
handled at runtime using the PCI vendor ID. This also allows mainboard
to easily multi-source WiFi chips and still use the same firmware
image without having to distinguish between the chip drivers.
BUG=b:169802515
BRANCH=zork
Change-Id: Ieac603a970cb2c9bf835021d1fb0fd07fd535280
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Refactor DPTF section of code under the baseboard devicetree
and overridetree. This makes override mechanism more simpler,
because not all the DPTF fields need to be overridden.
BUG=None
BRANCH=None
TEST=Built and tested on dedede system
Change-Id: I8e7cfe60c010ed4c07f9089325b289519e861f84
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Allow MRC training in SaGv low, mid and high frequencies.
TEST=Verify memory trains at low, mid and high SaGv point
through FSP debug logs enabled.
Change-Id: I0f60aad031ce9dfe23e54426753311c35db46c05
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45196
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add trackpad, touchscreen, and usb port to devicetree
BUG=b:160664447
BRANCH=NONE
TEST=build bios and verify theirs function for boten
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: I057f7d15d20d1a78acd733cc5463357e9c87afb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change drops maxsleep parameter from chip config and instead
hardcodes the deepest sleep state from which the WiFi device can wake
the system up from to SLP_TYP_S3. This is similar to how other device
drivers in coreboot report _PRW property in ACPI. It relieves the
users from adding another register attribute to devicetree since all
mainboards configure the same value. If this changes in the future, it
should be easy to bring the maxsleep config parameter back.
BUG=b:169802515
BRANCH=zork
Change-Id: I42131fced008da0d51f0f777b7f2d99deaf68827
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
If Cr50 is running old firmware version and hence does not ensure long
interrupt pulses, override the GPIO PM configuration.
BUG=None
TEST=Build and boot waddledee to OS. Ensure that any chip override
happens before FSP silicon parameter initialization. Ensure that the
suspend/resume sequence works fine. Ensure that the reboot sequence
works fine for 50 iterations.
Change-Id: I455c51d4a63b1b5edadbf00c786ce61b0ba1ff00
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Update TSR1 passive trip temperature
BUG=b:169691800
BRANCH=None
TEST=Built and tested on dedede system
Change-Id: I172391daca981d5591fa9cc5eacad92521dd0dc5
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
BUG=b:167472333
TEST=Build and boot dedede and observe the slope and offset values
getting updated in the fsp debug log
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I3ea32218040263f0abef9b9dd4c52efb16289fd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45825
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable CHROMEOS_DRAM_PART_NUMBER_IN_CBI on hatch, dedede, and volteer
to use the common version of mainboard_get_dram_part_num().
Remove duplicate instances of mainboard_get_dram_part_num().
BUG=b:169789558, b:168724473
TEST="emerge-volteer coreboot && emerge-hatch coreboot &&
emerge-dedede coreboot" and verify it builds.
Change-Id: I4e29d3e7ef0f3370eab9a6996a5c4a21a636b40e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45883
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change mainboard_get_dram_part_num() to return a constant character
pointer to a null-terminated C string and to take no input
parameters. This also addresses the issue that different SOCs and
motherboards were using different definitions for
mainboard_get_dram_part_num by consolidating to a single definition.
BUG=b:169774661, b:168724473
TEST="emerge-volteer coreboot && emerge-dedede coreboot && emerge-hatch
coreboot" and verify build completes successfully.
Change-Id: Ie7664eab65a2b9e25b7853bf68baf2525b040487
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45873
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch moves platform.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CNL and CML platform.
1) Dump and disassemble DSDT, verify _PIC method present inside
common platform.asl is still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I5189b03d6abfaec39882d28b40a9bfa002128be3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
add tcc, critical, passive policy, and pl values from thermal team
BUG=b:168353037
TEST=build and verify by thermal tool
Change-Id: I887d494ff097a881d519a456f24578a278323051
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45453
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. enable DRIVERS_INTEL_MIPI_CAMERA/SOC_INTEL_COMMON_BLOCK_IPU
2. add IPU/VCM/NVM/CAM0 in devicetree
BUG=b:166527568
TEST= build and verify function by cam ap on DUT
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: Ica6aa8ddc03a1dab5b548a759825dd3a4de3101f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45329
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Camera ACPI tables are generated at run-time for all variants of Dedede.
BUG=None
TEST=Build madoo variant.
Change-Id: Icb74c01a0a6dbc620466b64cd2b5652408ca41b9
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
BUG=b:168847046
TEST=emerge-dedede coreboot chromeos-bootimage
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I16ed22aa5e270ad2d5c964764cc134b72941d4e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The name GENERIC_SPD_BIN doesn't reflect anymore what that config is
used for, so rename it to HAVE_SPD_BIN_IN_CBFS.
Change-Id: I4004c48da205949e05101039abd4cf32666787df
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45147
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4151d1a6ce94763432f307fbc8bc4afe229856ea
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Enable processor thermal control using PCI dev path function instead of
Device4Enable parameter in devicetree. This change removes the dependency
on Device4Enable in devicetree. We can enable and disable this thermal
control using on and off support with PCI device entry in devicetree.
BRANCH=None
BUG=None
TEST=Built and tested on dedede board
Change-Id: I0463236996ad001af506c9966840b27fe44d60d2
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
After adjustment on madoo
Touch Pad CLK: 381.9 KHz
Touch Screen CLK: 389.4 KHz
Audio CLK: 380.9 KHz
BUG=b:168565823
BRANCH=master
TEST=USE=build madoo and measure by scope with madoo.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: If281f9a8614e3e0ef20893b456f46e68ecb0631d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add wifi sar for madoo.
Using tablet mode of fw config to decide to load custom wifi sar or not.
BUG=b:165105210
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ic6128b966c952cdc02a6359c14fa41f22265039a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
This change updates devicetree to enable SSDT generation for world
facing camera and user facing camera of Waddledoo. Also reverts DSDT
changes related to both the camera.
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Change-Id: Ib7e875d297c04f35d4e980ff33d9a3767d2910ac
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
This enables the keyboard backlight feature in ACPI for madoo.
BUG=b:167943993
TEST=Verified 'kbd_backlight' shows up in the '/sys/class/leds '.
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I11531699cb650b96becae5c1bec9f89c48b6bea0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
add the magolor touch screen ctrl devices:
1)elan 6915
2)elan 5012
3)raydium RM32680
BUG=b:166711761
BRANCH=None
TEST=build firmware and verify the touch functions on DUT
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: Icd2963317e858f7d35c937e45cd6f3e556bbb953
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45227
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add configuration for ALC5682 headphone jack and ALC1015 speaker
amplifier. Also turn on the HDA PCI device.
BUG=b:161667665
TEST=Build the boten board and verified the audio functionality.
Change-Id: I835db854543e6282c102c86a7073b432fd89d0a5
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44920
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Jasper Lake SoC supports PL2 (Power Limit2) as 20W. Increase PL2 value from 15W to 20W.
BRANCH=None
BUG=b:166656373
TEST=Built and tested on drawlat system
Change-Id: I82d6792907bb1c88cc9dd57d1eaeda8421c12fb2
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45162
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The debug statement to print WiFi SAR file can potentially have a NULL
pointer. Also the debug statement does not add much value. Hence remove the
debug statement.
BUG=b:165613510
TEST=Build and boot the drawcia board to OS.
Change-Id: I710240f5e965f523fb8ac55a67880e1cbf9abd48
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
drawman/drawlat/drawcia share the same coreboot, and only drawcia is convertible.
Use tablet mode of fw config to decide to load custom wifi sar or not.
BUG=b:165613510
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage.
Change-Id: Ibcd498021e63d0a172c71c3d94b60b3a25973467
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable FW_CONFIG and add tablet mode field in devicetree
BUG=b:165613510
TEST=emerge-dedede coreboot
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I55e4c0d0b4aa2337c01773006d0b485fdcd91654
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:165613510
TEST=emerge-dedede coreboot
Change-Id: Ic575889fd9b726a710abff78e1ecc8427b668d5d
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
CB:44774 introduced the non-existent SPD path. This is preventing the
device from booting up.
BUG=b:168053219
TEST=Build and boot drawcia board to OS.
Change-Id: I70ca5f4cf2c8e2e88ea5b1514b656caafb732743
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:162232776
TEST=Measured the I2C bus frequency as 389 KHz, high time as 870 ns and
low time as 1580 ns.
Change-Id: I67d2725a7fc8d83e3fa8a56cfa86540c4e6f0971
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45084
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:163743035
TEST=Measured the I2C bus frequency as 384 KHz, high time as 924 ns and
low time as 1680 ns.
Change-Id: I60a5f6814fb9818c724f6b6fe465ea49d0de0f97
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45083
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop duplicated code for spd.bin generation that is provided globally
in lib/Makefile.inc.
For all affected boards it has been verified that the output binary
functionally matches the original one. The changed execution order of
Make instructions influenced the cbfs file order. Hence, the rom images
can't be compared directly.
Thus, the output files of the two timeless abuild runs have been compared.
Further, it was verified that the final files in cbfs stay identical, by
comparing the extracted cbfs of each board.
The boards (possibly) needing modification could be found with something
like this (with false positives, though):
find src/mainboard -name Makefile.inc | \
xargs egrep 'SPD_BIN|SPD_DEPS' | cut -d: -f1 | sort -u
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Icd3ac0fd6c901228554115c6350d88bb49874587
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Setting USBx_PORT_EMPTY is not a requirement anymore, since unset
devicetree settings default to 0 and the OC pin now only gets set when
the USB port is enabled (see CB:45112).
Thus, drop the setting from all devicetrees.
Change-Id: I899349c49fa7de1c1acdca24994ebe65c01d80c6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
BUG=b:155002684
TEST=emerge-dedede coreboot chromeos-bootimage
Change-Id: I87d8575131e745dec818bc5864ca6b21ce0825af
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change lp4x spd names to include lp4x memory type (eg. lp4x-spd-1.hex).
BUG=b:160157545
TEST=run gen_part_id for volteer variants and verify that it changed
spd names to prepend the "lp4x-" to the filename..
Change-Id: I0c59da7eb78f34640aad2e852ca725d3e8571a8e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44784
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that generic SPD files have the memory type prepended to the
filename, they can be stored in the same location. This CL moves
the generic SPDs to the new location.
Change the ddr4 gen_part_id.go and gen_spd.go tools to use
"ddr4_spd_manifest.generated" instead of "spd_manifest.generated".
Change the lpddr4x gen_part_id.go and gen_spd.go tools to use
"lp4x_spd_manifest.generated" instead of "spd_manifest.generated".
Move TGL DDR4 and LPDDR4x generic SPDs into a common location.
Move JSL DDR4 and LPDDR4x generic SPDs into a common location.
Change the volteer/spd/Makefile.inc to use the new path for the spds.
Change the dedede/spd/Makefile.inc to use the new path for the spds.
BUG=b:165854055
TEST="emerge-volteer coreboot" and verify all variants build correctly.
Change-Id: I83b088cb718d15ffd3012c84a12b5231ae84a3e4
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44648
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:155002684
TEST=emerge-dedede coreboot chromeos-bootimage
Change-Id: I89a4a5bbcd26b156a9660f80090bb5c953196b84
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
By adding mainboard_smi_espi_handler, the espi smi can be handled
properly.
BUG=b:163382105
TEST=Tested lid close smi can be handled properly in depthcharge stage
Signed-off-by: Kane Chen <kane.chen@intel.com>
Change-Id: I8a2ecb52d5f6586f8acd57c4965b4238b95e3b64
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44564
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the configuration in device tree:
1. Add HDA,speaker codec and speaker amp setting
2. Add Elan and Goodix touchscreen setting
3. Add user facing camera usb setting
4 Add Synaptics and Elan Touchpad setting
5. Add WiFi configuration
BUG=None
BRANCH=None
TEST=build magolor firmware
Change-Id: Ifc562b4a05c8955d2aec105f2f429f926ad1e702
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44633
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add charger input current throttling for drawcia system
BUG=None
BRANCH=None
TEST=Built and tested on drawcia system
Change-Id: I34fdc23fcd84b5c27c2bada769f7a9049c2a56a5
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This will ensure that the cold reset is performed when CSE Lite jumps
from RO to RW.
BUG=b:162386991
TEST=Ensure that Drawcia board boots to OS. Ensure that global reset is
triggered when cr50 is running firmware versions newer than 0.0.22. On
cr50 versions 0.0.22 or older, EC triggers cold reset of AP.
Change-Id: I46a390c71e380328cd7fe70214df09553b2db75c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
IPU is required to be enabled for platform supporting MIPI camera.
IPU is by default disabled in devicetree for all variants. Enable
IPU for Waddledoo and Waddledee supporting MIPI camera.
BUG=None
BRANCH=None
TEST=IPU is enabled for platforms and enumerates in lspci.
Change-Id: Ia3cf06d78be4301c68bfa8b1118ddff231d24a66
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44271
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kconfig 5.8 interprets $(...) itself using environment variables, which
generally means that they expand to the empty string. \$(...) works
with both our current and new Kconfig with the desired behavior
(to pass it through unmodified).
Change-Id: I726567eeb61d2035560152677d2b4548c1472be9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44584
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure TRACKPAD_INT_ODL pad reset config to DEEP and
map PMC_GPE_DW to PMC_GPP values.
TEST=System should wake from S3 via trackpad
Change-Id: I58ce3720e0fdeefb2c9440bb3006897ef80211ea
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Add supported memory parts in the mem_list_variant.txt and generate the
SPD ID for the parts. The memory parts being added are:
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNBKMMLXR-NEE
MT53E1G32D2NP-046 WT:A
K4UBE3D4AA-MGCR
And also remove the deprecated by cl#43989
https://review.coreboot.org/c/coreboot/+/43989
BUG=None
TEST=Build the magolor board
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I3348b7fbeff038b85e7d3c9137517e05a35bf3dd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44408
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates the SLP_Sx assertion width and power cycle duration
for the dedede platforms.
Power cycle duration:
With default value,
S0->S5 -> [ ~4.2 seconds delay ] -> S5->S0
With value set to 1,
S0->S5 -> [ ~1.2 seconds delay ] -> S5->S0
BUG=b:159104150
TEST=Verified that the power cycle duration is ~1.2s with global
reset on waddledoo.
Change-Id: I7079cbd564288b5d5b69e07661434439365063d3
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
When CSE Lite jumps from RO to RW, global reset is initiated. When AP is
reset as part of global reset, TPM initialization fails. This is because
AP reset is not detected by TPM hosting an older firmware version. Request
Embedded Controller (EC) to perform AP reset so that TPM can detect that
event.
BUG=b:162290856, b:162386991
TEST=Ensure that the device boots to OS with the board-specific reset
sequence when CSE Lite jumps from RO to RW with an older and newer Cr50
firmware.
Cq-Depend: chromium:2337430
Change-Id: Ib1f7271130e0b4b68c7f0917ecc4eadba1486206
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Add DTT (Dynamic Tuning Technology) support on Jasper Lake based drawcia
system. Add information on sensors, power limits and tcc_offset for DTT
based thermal control.
BRANCH=None
BUG=b:161993459
TEST=Built for dedede system
Change-Id: If50052864fb246a6a8f7d96fa50529e5f55968c0
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Decrease the SPI ROM size from 32 MB to 16 MB
BUG=b:58540772
BRANCH=None
TEST= build firmware and check the magolor bin size
Change-Id: Ie7ddf698fde1dbf663859d5654946bc08abe737c
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Use tabs instead of eight (sometimes less) spaces.
Change-Id: Ic3d61f5210d21d9613fc50b47b90af71f544169a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Observed thermal shutdown initiated by DPTF due to CPU temperature
reaching critical temperature trip value. During stress testing with
heavy workload like WebGL Aquarium, sometime CPU temperature spikes
till 99 degree Celsius and DPTF initiates system shutdown. This
updates CPU critical temperature trip value to 105 degree Celsius
to avoid system shutdown.
BUG=b:161993459
BRANCH=None
TEST=Built and tested on dedede system
Change-Id: If15a873a997aa80f20940f27bbafd4498908c091
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44054
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add RTL8822CE support for Madoo.
BUG=b:162390420
BRANCH=None
TEST=FW_NAME=madoo emerge-dedede coreboot chromeos-bootimage, build successful
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I6e471be2b2856977e6f728d5a2ca78942725bea6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
1. Add Elan touchpad support.
2. Follow schematic to disable I2C1 and I2C3.
BUG=b:160869188,b:161407664
BRANCH=NONE
TEST=emerge-dedede coreboot chromeos-bootimage", build successful
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I154a1ff2597968d200d1d0693718f90cd2744616
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44052
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Add Goodix touchscreen support.
BUG=b:160868197
BRANCH=None
TEST=emerge-dedede coreboot chromeos-bootimage", build successful
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I9bf27d69d0895cb4ea8620a6da49e98d25e05c23
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44012
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add overridetree info for the touchscreen.
BUG=b:160129126
TEST=cros flash-ap -b dedede
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: I55fc0749b824a0bf4b615d02bd8bc39bcdd589e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add supported memory parts in the mem_list_variant.txt and generate the
SPD ID for the parts. The memory part being added is:
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNBKMMLXR-NEE
MT53E1G32D2NP-046 WT:A
K4UBE3D4AA-MGCR
BUG=None
TEST=Build the magalor board.
Change-Id: I7bb19d6d4a66e66fed0564592c803c2af1045b0c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add supported memory parts in the mem_list_variant.txt and generate the
SPD ID for the parts. The memory parts being added are:
H9HCNNNBKMMLXR-NEE
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
BUG=b:161215903
BRANCH=NONE
TEST=FW_NAME=madoo emerge-dedede coreboot chromeos-bootimage
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ib61af2399541c4caf4a310a34e778e0ba1cbd3ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43802
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select the drivers for ALC5682 codec and MX98360A spk amp
BUG=b:161407664
BRANCH=NONE
TEST=FW_NAME=madoo emerge-dedede coreboot chromeos-bootimage
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ibe3d878b1058bfae4143d96be854884e61394ad5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Follow schematic to modify USB port setting and clean up I2C clock tuning.
USB2 [0]: USB Type C Port 0
USB2 [1]: USB Type C Port 1
USB2 [2]: None
USB2 [3]: USB Type A Port 1
USB2 [4]: None
USB2 [5]: Camera
USB2 [6]: None
USB2 [7]: WLAN module - BlueTooth
USB3 [0]: USB Type C Port 0 (M/B side)
USB3 [1]: USB Type C Port 1 (Sub/B side)
USB3 [2]: None
USB3 [3]: USB Type A Port 1
USB3 [4]: None
USB3 [5]: None
BUG=b:161407664
BRANCH=NONE
TEST=Build the coreboot image on madoo board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ia73593f52adee3806e725127891f084a08bf1360
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43750
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow schematic to modify some GPIO pins.
GPP_D12 - NC Pin
GPP_D13 - NC Pin
GPP_D14 - NC Pin
GPP_D15 - NC Pin
GPP_E0 - NC Pin
GPP_E2 - NC Pin
GPP_H6 - NC Pin
GPP_H7 - NC Pin
GPP_S02 - NC Pin
GPP_S03 - NC Pin
BUG=b:161407664
BRANCH=NONE
TEST=Build the coreboot image on madoo board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I85aadfb0d020055eec921c7646c16ae6c95a606f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43745
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:161734657
TEST=Ensure that the discrete WiFi information is built into ACPI table.
Scope (\_SB.PCI0.RP01)
{
Device (WF00)
{
Name (_UID, 0x923ACF1C) // _UID: Unique ID
Name (_DDN, "WIFI Device") // _DDN: DOS Device Name
Name (_ADR, 0x00000000) // _ADR: Address
Name (_PRW, Package (0x02) // _PRW: Power Resources for Wake
{
0x43,
0x03
})
}
}
Change-Id: I9a9259e167fc213291b89e151729553ec4649eaf
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43769
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
MRC automatically detects the DDR type and sets Rcomp resistor
and target values for JSL and does not require explicit programming.
Change-Id: Ia130765e2cb91d6a39ad00ebbab20e7e87fa42d1
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Create the magolor variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
BUG=b:58540772
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_MAGOLOR
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I3e39e650b82a0aa629a48a00227700b058effb34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Adjust GPIO setting to match boten design
BUG=b:160741777
BRANCH=NONE
TEST=Add gpio.c for boten
Signed-off-by: Yan Liu <yan.liu@bitland.corp-partner.google.com>
Change-Id: I4eafee608f657f8ec5a06caf6e99b08b3330512b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43277
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
HDMI DDC GPIOs were configured as NC till now in waddledoo.
This may cause HDMI i2c transfer to break and EDID read will
fail due to wrong configuration
Configuring these GPIOs as NF in coreboot to fix the issue.
BUG=b:160324327
BRANCH=None
TEST=HDMI works on DDI2 onn Type-C port
Change-Id: If02f062132d7c3b01b07ea9401e81f451df35c3c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43294
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Iac0f0c3d102a9a900ac168f8be907349d9a3dd42
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43565
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:155002684
TEST=build drawcia, and check touchscreen can work
Change-Id: I29a891e07bb3c1d8ebe17666c18bfcf3bc1c361d
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Change-Id: I7378aa7d6156ece3ab3959707a69f45886f86d21
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43593
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Reset the Touchscreen (TS) and disable the stop GPIO (report switch) at
the same time. Add a delay of 100 ms after disabling the stop GPIO. This
will ensure the required delay is inserted for both reset and stop
disable GPIOs simultaneously.
BUG=b:152936541
TEST=Build and boot the waddledoo mainboard. Ensure that the SiS
Touchscreen is functional.
Change-Id: Icbfb5e07a28ab72b1ff696ad1183a6c2173dcaac
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43453
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add supported memory parts in the mem_list_variant.txt and generate the
SPD ID for the parts. The memory parts being added are:
H9HCNNNBKMMLXR-NEE
K4U6E3S4AA-MGCR
BUG=None
TEST=Build the drawcia board.
Change-Id: Id05c0b2a87b64bfedc761949cbc8ad6cf7dd73a5
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43505
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables the CSE Lite SKU for the dedede baseboard.
BUG=b:160201335
TEST=Build and boot waddledoo with CSE Lite SKU.
Cq-Depend: chrome-internal:3142530
Change-Id: I24d7d715d55524807af0127aa4a346a008164b8c
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41818
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
This patches enables the SkipCpuReplacementCheck config for
the dedede baseboard to avoid the forced MRC training for all
its variants with the soldered down SOC.
BUG=b:160201335
TEST=Build and verify CSE Lite SKU on Waddledoo.
Cq-Depend: chrome-internal:3142530
Change-Id: I611e66f74a3b9b090ab5e0d836231643d3f919dc
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Create the madoo variant of the waddledoo reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
BUG=b:161191394
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_MADOO
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I6d3f611606f86036d67be9c8b0fda833ab61ecc1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
1. Update Link frequency to 180 Mhz
2. Set data-lanes to 1 and
3. Update the clock-lane used by sensor
BUG=b:155285666
BRANCH=None
TEST=Build and able to capture image using user facing camera.
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Change-Id: I164cb6af1003de561be8ce640e7653b7bcb3a22f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Since there is now a mechanism to generate DPTF ACPI tables and methods
at runtime, dedede should switch to using that instead of raw ASL files.
This patch converts the existing .asl files into devicetree entries.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6bb6e6e15f50a1e510080e16bbca09dfc5f16b1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43422
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SiS9813 USI touchscreen support.
BUG=b:160129126
TEST="emerge-dedede coreboot chromeos-bootimage", build successful.
Change-Id: I42fdc5e8243d2c70c953b2f516c10f84a041c035
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43304
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For variants with slightly different GPIO configuration, add support to
pass an override GPIO configuration table.
BUG=None
TEST=Build and boot the waddledee mainboard.
Change-Id: I2f1c6dc2ea5499bff96a471c4461339ef01ee19a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
