| Age | Commit message (Collapse) | Author |
|---|
|
Enable Acoustic noise mitigation for blipper and set slew rate to 1/8
which is calibrated value for the board.
BUG=b:187760191
BRANCH=dedede
TEST=build firmware to UPD and Acoustic noise test
Change-Id: I187702c23712416eaaaaf1e210dcfc6b2c560041
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
On dedede boards without Cr50, the CrOS Board Info (CBI) EEPROM write
protect signal is decoupled from the hardware write protect signal.
Instead, we'd like for it to mirror the software write protect status.
This commit simply checks the software write protect status of the SPI
flash and sets the CBI EEPROM write protect if it's enabled. To prevent
changing the WP signal at run-time, the GPIO configuration is also
locked down after the level has been set. If HW WP is deasserted, the
CBI EEPROM WP will be deasserted as well.
BUG=b:191189275,b:184592299
BRANCH=None
TEST=Build and flash lalala, disable SW WP by running `flashrom -p host
--wp-disable` from a root shell and verify that the GPIO is asserted
after a reboot. Export the gpio via sysfs and verify that attempting to
change the value of the GPIO is futile. Enable SW WP via `flashrom -p
host --wp-enable` and reboot the DUT. Again, export the GPIO via sysfs
and verify that attempts to change the GPIO value are futile.
localhost ~ # iotools mem_read32 0xfd6e08d0
0x44000200
localhost ~ # cd /sys/class/gpio/
localhost /sys/class/gpio # echo 217 > export
localhost /sys/class/gpio # cd gpio217/
localhost /sys/class/gpio/gpio217 # echo out > direction
localhost /sys/class/gpio/gpio217 # cat value
0
localhost /sys/class/gpio/gpio217 # echo 1 > value
localhost /sys/class/gpio/gpio217 # cat value
1
localhost /sys/class/gpio/gpio217 # iotools mem_read32 0xfd6e08d0
0x44000200
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: Ic103037921ec7d2f96f86178675c11a3a1357d1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Configure I2C high / low time in device tree to ensure I2C
CLK runs under I2C_SPEED_FAST (400 kHz).
Touchpad: 387.7kHz
Touchscreen: 389.4kHz
Audio: 387.6kHz
P-sensor: 372.5kHz
BaUG=b:178092096
BRANCH=dedede
TEST=Build and EE check after tuning I2C clock is under 400kHz
Change-Id: I4f6bdd3802cd94671325a89458cde981a2ffa929
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Create the cappy variant of the waddledee reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:190515828
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CAPPY
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: Id5a3b0cb475ee77a9f62523d8322a5e4123ce3be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add camera support in devicetree.
BUG=b:190797339
BRANCH=None.
TEST=built pirika firmware and verified camera function is OK.
Change-Id: I66ded32105f3166e2faec3ea5dcfb93c29822366
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55450
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix build failures in the case <vc/.../chromeos.h> is removed.
Change-Id: Ie45066f39cd6fb92cca697a6bd5bc8bb8c60b4e7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
speaker L/R
Add Realtek audio codec ALC5682I and speaker L/R the same way as in waddledee
BUG=b:188446060
BRANCH=dedede
TEST=Boot to check ALC5682I and speaker L/R are functional
Change-Id: I8173ffbfb1a8f18978a5e35c69972d4a6d8cb04a
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54529
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add low_power_probe config to camera devices so that driver skips initial
probe during kernel boot and hence prevents privacy LED blink.
BUG=b:178060668
TEST=Build and boot to OS on Drawcia. Ensure no blink on privacy LED.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I00dfe2ce0b57ff3eaa258204f49e79a280754dcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52190
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct GPIO settings as below reason:
1. GPP_D19/GPP_D20/GPP_D21 not being used but set to NF.
2. GPP_B7 should configure as WWAN SAR detect ODL, but set to GPI
BUG=b:188956448
BRANCH=dedede
TEST=The LTE DPR pin can be pulled down normally when someone
get close to the P-sensor antenna.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Idc214fcd9c4631368a71f4d59bb644df739982ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:181189479
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I379c0ea79a7c27bdd81ed41a54135f7284fb6412
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Configure GPIO D22/D23/E11.
Add P-sensor to device tree, these registers are draft version.
BUG=b:178092096
BRANCH=dedede
TEST=built firmware and dmesg shows STH9324 initial success.
Change-Id: I2c8feedd6efc1a471304322a17480c836e22349e
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:180875580
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Id18a38cddbcacbafbe2c54d94dbda5e00de02b3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
Add Goodix GT7996F touchscreen into devicetree for cret.
BUG=b:180547935, b:188501391
BRANCH=dedede
TEST=Built cret firmware and verified touchscreen function.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I2a6f7c1e9900492937202c0bc6595674f1e79e5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Configure I2C rise/fall time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (<400 kHz).
Measured I2C frequency changes are just as below after tuning:
touchpad: 434kHz ---> 391kHz
touchpanel: 439kHz ---> 382kHz
audio codec RT5682: 445kHz ---> 385kHz
BUG=b:187555396
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400 kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I8438e37be49f8a74f53fd8460110dac1a3f06993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add Elan eKTH7D18 touchscreen into devicetree for cret.
BUG=b:180547935, b:187484857
BRANCH=dedede
TEST=Built cret firmware and verified touchscreen function.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Iab87ddfc7b46420439efa3e7e55c88ad4c27155d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Configure I2C rise/fall time in device tree to ensure I2C
CLK runs accurately (380<frequency<400 kHz).
Measured touchpad I2C frequency is 394 kHz
BUG=b:189740533
BRANCH=dedede
TEST=Build bios and make sure frequency meets specification.
Change-Id: Ibc0504a5be6fe9237b8b30783c659a761d10561a
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
There are two touch pads that Sasukette used have the same I2C address.
It will show "/dev/input/event4: SPPT2600:00 06CB:CE9D Touchpad" when
the Synaptics touch pad is connected after running evtest under VT2.
BUG=b:189520603
BRANCH=dedede
TEST=It will show "/dev/input/event4: SYNA0A00:00 06CB:CE9D Touchpad"
when the Synaptics touch pad is connected after running evtest under VT2.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: If0bd80baa27dfeb7bcb43f0ca4b02e1228e372a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55035
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update devicetree and gpio driving of storo that enable stylus
Updates the GPIO configuration for GPP_C12 to
PAD_CFG_GPI_GPIO_DRIVER and device tree entry for PENH device to
use WAKEUP_ROUTE_GPIO_IRQ.
BUG=b:188519508,b:188365033
BRANCH=dedede
TEST=build bios and the pen behavior can be detected.
Change-Id: I2ffc969569b3ca29ba76326140f958a9707199f7
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
haboki/habokay is the same design as drawlat/drawcia, and differs only
in replacing Cr50 with discrete TPM.
BUG=b:187094464
TEST=FW_NAME=haboki emerge-keeby coreboot
Cq-Depend: chrome-internal:3850094
Change-Id: Id866927b7041c5bf1c73fb4f0c03798eb61efa79
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54755
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new memory MT53E512M32D1NP-046 WT:B in the mem_parts_used.txt and
generate the SPD ID for the parts.
BUG=b:183057749
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ib797af858e8f7ea275291e552102db74f4724aad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54747
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ELAN touchpad into devicetree for sasukette.
BUG=b:188376649
BRANCH=dedede
TEST=built sasukette firmware and verified touchpad function
Signed-off-by: lizhi7 <lizhi7@huaqin.corp-partner.google.com>
Change-Id: I898aeda936eb10ef4ead679a1c087060fad71a08
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54369
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drawper would use synaptics touchpad.
BUG=b:184878424
TEST=emerge-dedede coreboot and check touchpad function work.
Change-Id: I2d2c205e19d8e3472e0fa7ca20fd38e381ac0de0
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Drawper support LTE+HDMI,
so use DB_PORTS_1A_HDMI_LTE to select HDMI VBT output for it.
BUG=b:186393848
BRANCH=dedede
TEST=Build and boot to OS check HDMI output works.
Change-Id: Ibf34cce1e3cbfce8a71dce880c50f85db9295b1e
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
DB_PORTS_1C_1A_LTE 6
DB_PORTS_1C 7
DB_PORTS_1A_HDMI_LTE 8
BUG=b:186393848
BRANCH=dedede
TEST=build pass
Change-Id: I8632960d7e538402bf033d07402116dac848f5ac
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Move discrete TPM in the devicetree to avoid emitting the following
message: "Using default TPM ACPI path: '\_SB_.PCI0.LPCB'"
There is no corresonding ACPI device for 1f.5 PCI device. Therefore,
move the discrete TPM to a device that has the corresponding ACPI
device node. Functionality should remain the same.
BUG=b:187518267
Change-Id: Ie9ec70336d5651c87f06f8b357abd1bfdb1cc06b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
|
|
Add ELAN Touchpad device under I2C0
BUG=b:188373661
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Change-Id: I15b9cb0d0276b5e2dd06694530cc35e5643efb9d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52936
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable/disable LTE function based on LTE bit of FW_CONFIG.
The LTE function settings are included GPIO settings, USB port settings and
power off sequence.
BUG=b:187797408
BRANCH=dedede
TEST=Build and test the change on cret.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ib926e99aaf9df433a7cff71180ee55431d69f718
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
DPTF parameters from thermal team.
1. Modify TSR1 sensor as charge sensor.
2. Modify P-state parameter
BUG=b:180641150
BRANCH=dedede
TEST=build and verified by thermal team.
Change-Id: I43002db61de650d29cd85944a4eaea1b2f99aec4
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52755
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select touchscreen(s) based on touchscreen source provisioned in SSFC of CBI (higher 32 bits of FW_CONFIG in coreboot).
The reason is to avoid to enable multiple touchscreen ICs with the same slave address.
BUG=b:186609348
TEST=build and boot to OS.
Change-Id: I087ea677a8865fc8c5b3f7c9773bd7f97924dbb3
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
|
|
Remove TSR2 and use DPTF parameters from internal thermal team.
BUG=b:175938681
TEST=build and boot to OS.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: If0ec1ec48b8971efe87f1f8d10332a9c16352122
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Probe the fw_config for RT1015 speaker amplifier operation mode and
enable it accordingly in the device tree.
BUG=b:180570923
BRANCH=dedede
TEST=ALC1015Q-VB drive speaker OK
Change-Id: I756bfa6f604ed320de9a515821979aa95c869ebf
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add support for GPIO and SPD driver for pirika
BUG=b:184157747
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Change-Id: Id367a83b04aad62b7deabae99b3f91905a2fc46c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update LTE USB port configuration at run-time after probing the firmware
config. By default the concerned USB port takes the Type-A port
configuration.
BUG=b:186380807
BRANCH=dedede
TEST=Build and boot to OS in metaknight
Change-Id: I5ad5a1670adef54075923cf912fb41a1ce776155
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
|
|
This callback is required to update the devicetree config at run-time
after probing the firmware config.
BUG=b:186380807
BRANCH=dedede
TEST=Build and boot to OS in metaknight.
Change-Id: I857211bfc4beb36ab225f3786c1707336a34aae9
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
|
|
Create the pirika variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:184157747
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_PIRIKA
Signed-off-by: kirk_wang <kirk_wang@pegatron.corp-partner.google.com>
Change-Id: I57bf33deeadacc88800f9ce1d3d54385ba56c798
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52626
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify reset pin setting to ACPI_GPIO_OUTPUT_ACTIVE_LOW for
ELAN and Weida touchscreen.
BUG=b:180547621
BRANCH=dedede
TEST=Build the cret board and touchscreen is workable.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I912fe8a0e18a4c3527fb8587592b855c93b12406
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Default VBT supports only integrated Display port. Magister supports a
HDMI port and hence support a separate VBT for Magister.
BUG=b:180666608
BRANCH=dedede
TEST=Build and boot to OS.
Cq-Depend: chrome-internal:3661227
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I52c10452887312959f68cfc4e25d5897dae388f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51279
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Because galith/gallop both non-suport tablet mode,
remove un-use fw_config conditional.
BUG=b:176206495
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage.
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ic9bb76c207ef033f81ecdd57849535b8ac8d13ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52565
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Define TOUCH_RPT_EN pin(GPP_A11) as the stop_gpio for the touch screen
and control TOUCH_RPT_EN pin to keep low.
BUG=b:176253069
TEST=Build and boot metaknight to OS, confirm GPP_A11 pin keep low.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I816e29eccac0f1935aeaa3b94c907870e2451e3a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52653
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, it fails to dump the nvme data by test command.
It reports the following error:
cat: '/sys/bus/i2c/devices/i2c-PRP0001:01/eeprom': Connection timed out
So increase the value from 0x0400 to 0x2000 and double the address width from 0x08 to 0x10 to solve this problem.
BUG=b:177393430
TEST=1. cat /sys/bus/i2c/devices/i2c-PRP0001:01/eeprom > /tmp/ov8856_eeprom.bin
2. hexdump -C /tmp/ov8856_eeprom.bin > ov8856_eeprom_dump.log
3. cat ov8856_eeprom_dump.log
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ia933927981f07e0f7954a4bc6d82f0bdd70181f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52048
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: ShawnX Tu <shawnx.tu@intel.com>
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch has changes to support multiple cameras modules, based on
the value set in the SSFC_CONFIG.
BUG=b:176065425
TEST=Tested the changes with magolor 5MP and 8MP camera.
Change-Id: I764abf70bacbe61452e7b0fd59c1b375227b5748
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add control charging current from TSR0 and correct charger_perf table value.
BUG=b:179067801
BRANCH=dedede
TEST=emerge-dedede coreboot
Change-Id: Ie0d969898defe76952e5c136fa93b7edffe51de3
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Edward Doan <edoan@google.com>
|
|
Metaknight has two daughter-board (DB_PORTS_1A_HDMI and
DB_PORTS_LTE_HDMI), LTE and USB Type A use the same usb port,so needs to
probe daughter-board to avoid USB device cannot recognize correctly.
BUG=b:184809456
TEST=build and verify USB device can recognize correctly
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ie42d12c7ce5c7341751c3cf92b5f37b6cd4d479f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52369
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raymond Wong <wongraymond@google.com>
Reviewed-by: Kaiyen Chang <kaiyen.chang@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
support audio AMP selection with fw_config.
BUG=b:185082705
BRANCH=dedede
TEST=build pass
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ieb169c69a6716082dd218d05479bca46bbc09a3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add AUDIO_AMP ports bit field in devicetree.
UNPROVISIONED 0
MAX98360 1
RT1015_I2C 2
RT1015P_AUTO 3
BUG=b:185082705
BRANCH=dedede
TEST=build pass
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I54f1e44036857dc00df074c38fde0fa82e589320
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52317
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify GPIO_D22/D23/E11 configuration for P-sensor
BUG=b:185214363
BRANCH=dedede
TEST=built storo firmware and verified P-sensor function
Change-Id: Ia2df1a227b04688a6b98384cd3a4e63023c0c1d9
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add LTE modem to devicetree
Configure GPIO control for LTE modem
BUG=b:178092096
TEST=Built image and verified with command modem status
Change-Id: Id8f483e1132a08500fbe950711cc84197ce40b12
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:185084331
BRANCH=dedede
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ie982741cb7b328623cf27f41c31f819e8cdb7bc9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add wifi sar for botenflex.
Due to fw-config cannot distinguish between boten and botenflex.
Using sku_id to decide to load botenflex custom wifi sar.
Detail reason for using sku_id in b:182433707.
BUG=b:182433707
TEST=build and test on boten/botenflex
Cq-Depend: chrome-internal:3686313
Change-Id: Id3f2529a7ad56ff306df98f77cda556656da52a5
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
DPTF HIDs are different per-platform going forward, so refactor these
into SoC-specific structures which the DPTF driver can query at runtime
for platform-specific information.
Change-Id: I6307f9d28f4274b851323ad69180ff4ae35053da
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This commit enables HECI such that interface can be used from
userspace on the dedede mainboards.
BUG=b:184219504
TEST=Build and flash drawcia, verify that Intel Flash Programming Tool
can communicate with the Converged Security Engine.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: I5b28c471d6554a5e14538073d48ef47da05936fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable Acoustic noise mitigation for boten and set slew rate to 1/8
which is calibrated value for the board.
BUG=b:180668001
BRANCH=dedede
TEST=build firmware to UPD and Acoustic noise test
Change-Id: I75851bd7c279feeab4ab94f4c82d55bf0e5ce316
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update devicetree and gpio setting of metaknight to handle pen detection.
BUG=b:180426949
TEST=Build and check behavior is expected.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ieeca20eff57b16217a13d996dca3f662911f3e5a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add LTE module support into devicetree and associated GPIO configuration.
BUG=b:183774169
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I14684bb30e46bf845a401649f56b16b60db379e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Select the drivers for DA7219 codec and MAX98360A spk amp
BUG=b:183771323
BRANCH=dedede
TEST=emerge-dedede coreboot chromeos-bootimage
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I3fd7c374fc8214e25a28fb9ba62a9c8473d3f755
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51841
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove TSR2, use DPTF parameters from internal thermal team.
BUG=b:183749595
BRANCH=dedede
TEST=emerge-dedede coreboot
Change-Id: I3182b96bf36c8d07299fe435a29e6b8c0b8a6927
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Configure I2C rise/fall time in device tree to ensure I2C CLK runs
accurately at I2C_SPEED_FAST (< 400 kHz).
Measured I2C frequency just as below after tuning:
I2C0(touchpad): 385 kHz
I2C4(audio): 380 kHz
BUG=b:180335053
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400kHz
Change-Id: Ic92ee0379456e80260a8026bc38ee41325dad6d2
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The Lalala variant is a design that differs only
in replacing Cr50 with a discrete TPM part.
BUG=b:184151664
Change-Id: I2f7abb9637cd5a13ac896396781b19feb156c948
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
|
|
There are forthcoming designs that will be utilizing
a discrete TPM 2.0 solution. Split the existing dedede
configuration options so future mainboard variants can
easily select the appropriate Kconfig option using the
newly introduced options:
- BOARD_GOOGLE_BASEBOARD_DEDEDE_CR50
- BOARD_GOOGLE_BASEBOARD_DEDEDE_TPM2
The existing variants all select the former option,
BOARD_GOOGLE_BASEBOARD_DEDEDE_CR50 since all those
designs currently utilize Cr50.
BUG=b:184151664
Change-Id: I2bdb1ca4fd78cc0628256d49678ea042c55f6fba
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52030
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Acoustic noise mitigation for lantis and set slew rate to 1/4
which is calibrated value for the board. Other values like PreWake,
Rampup and RampDown are 0 by default.
BUG=b:183561593
BRANCH=dedede
TEST=EE verify acoustic noise test passes.
Change-Id: I5e5f24ed934910726c220678068d085b6ee2bcf6
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Thermal sensor2 defined in baseboard do not exist in boten.
With the format the DPTF policies are defined in boten, all the entries
from the baseboard are included and then the overrides applied.
This causes the non-existent DPTF devices to be exported in the ACPI table
and in turn OS reading invalid temperatures. Fix the format for
DPTF passive and critical policies.
BUG=None
BRANCH=dedede
TEST=Build and boot to OS in boten. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Change-Id: I63c781e0a439f1e7a3525fa7cf290fa9300cb066
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ben Kao <ben.kao@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Enable gpio mode driver for ALC1015 AMP Auto Mode.
BUG=b:181732574
BRANCH=dedede
TEST=ALC1015Q-VB drive speaker OK
Signed-off-by: lizhi7 <lizhi7@huaqin.corp-partner.google.com>
Change-Id: Idc5b190fc2c30689feaf08229b2a75c69894ac5e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51763
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable gpio mode driver for ALC1015 AMP Auto Mode.
BUG=b:177868812
BRANCH=dedede
TEST=ALC1015Q-VB drive speaker OK
Signed-off-by: lizhi7 <lizhi7@huaqin.corp-partner.google.com>
Change-Id: Ic7deb9be6444d85d32ff94ce8e4a140dbdea349e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Configure I2C high / low time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (400 kHz).
Measured I2C frequency just as below after tuning:
touchpad:371.63 kHz
touchpanel:368.24 kHz
audio codec RT5682:369.13 kHz
speaker AMP L:366.21 kHz
speaker AMP R:365.8 kHz
P-sensor:368.34 kHz
MIPI Camera:363.35 kHz
BUG=b:181589325
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I1a755a54540e106b41ac427f84989ed7e8037558
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51624
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds support zinitix touchpad for sasuke.
BRANCH=dedede
BUG=None
TEST=built and checked touchpad worked on sasuke
Change-Id: I85794311c49e33c4683482e125bea5ca2dbacfa8
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add ELAN and Weida touchscreen into devicetree for cret.
BUG=b:180547621
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Icdb7aabe4a9ecd7b5a057c4644799aa537adb6ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
1. Support Elan touchpad.
2. Support JYT touchpad.
3. Follow schematic to disable I2C1 and I2C3.
BUG=b:183454249, b:180547781
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I8c150c3f65d0e057d5ba1b07ec1c20886f02ef6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51726
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
1. H9HCNNNBKMMLXR-NEE
2. MT53E512M32D2NP-046 WT:F
3. K4U6E3S4AA-MGCR
BUG=b:183057749
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Iacfdd9a27f126ba4b97d1a6493bcc09bb31454a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51619
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow schematic to modify USB port settings.
USB2 [0]: USB Type C Port 0
USB2 [1]: None
USB2 [2]: USB Type A Port 0
USB2 [3]: LTE
USB2 [4]: None
USB2 [5]: Camera UFC
USB2 [6]: Camera WFC
USB2 [7]: Integrated Bluetooth
USB3 [0]: USB Type C Port 0 (M/B side)
USB3 [1]: None
USB3 [2]: USB Type A Port 0 (M/B side)
USB3 [3]: LTE
BUG=b:182973703
BRANCH=dedede
TEST=Build the coreboot image.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I80447d6ac3422f858a9022f550b4f42353819405
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Follow schematic to modify some GPIO pins.
GPP_C12 - NC Pin, UP_20K
GPP_C18 - NC Pin
GPP_C19 - NC Pin
GPP_C22 - NC Pin, UP_20K
GPP_D12 - NC Pin
GPP_D14 - NC Pin
GPP_D15 - NC Pin
GPP_D19 - NC Pin
GPP_D20 - NC Pin
GPP_E0 - NC Pin
GPP_E2 - NC Pin
GPP_H1 - NC Pin
GPP_H6 - NC Pin
GPP_H7 - NC Pin
GPP_G0 - NC Pin
GPP_G1 - NC Pin
GPP_G2 - NC Pin
GPP_G3 - NC Pin
GPP_G4 - NC Pin
GPP_G5 - NC Pin, UP_20K
GPP_G6 - NC Pin
GPP_G7 - NC Pin
BUG=b:183078393
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Id966884f3e36303b636fa13ef9baecccae87604a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Create the cret variant of the waddledoo reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:181325655
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CRET
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I700201cf81b25c6776df3ec9fc843cd9bd8c88c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Add USB Port configuration into devicetree for storo
BUG=b:177389444
BRANCH=dedede
TEST=built firmware and verified USB3.0 function is OK
Change-Id: I1527c7178ffac9b2322eb65aab6e2086d949e47c
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable gpio mode driver for ALC1015 AMP Auto Mode.
BUG=b:176956779
BRANCH=dedede
TEST=ALC1015Q-VB drive speaker OK
Change-Id: Iaa5650e120362e81fa36530f6a207c9c07e1139a
Signed-off-by: wuweimin <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
DPTF paramerters from thermal team.
1. PL2 =15W
2. Add TSR sensor charger, 5V regulator
BUG=b:177249297
BRANCH=dedede
TEST=build image and verified by thermal team.
Change-Id: Ia5f6cc2a4564bb5558cbaca8daf31ee70145019f
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Currently, if `get_wifi_sar_cbfs_filename()` returns NULL, then
`get_wifi_sar_limits()` assumes that the default filename is used for
CBFS SAR file. This prevents a board from supporting different models
using the same firmware -- some which require SAR support and some
which don't.
This change updates the logic in `get_wifi_sar_limits()` to return
early if filename is not provided by the mainboard. In order to
maintain the same logic as before, current mainboards are updated to
return WIFI_SAR_CBFS_DEFAULT_FILENAME instead of NULL in default
case.
Change-Id: I68b5bdd213767a3cd81fe41ace66540acd68e26a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51485
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that SAR support in VPD is deprecated in coreboot, there is no
need for a separate Kconfig `WIFI_SAR_CBFS` as the SAR table is only
supported as a CBFS file. This change drops the config `WIFI_SAR_CBFS`
from drivers/wifi/generic/Kconfig and its selection in
mb/google/.../Kconfig.
wifi_sar_defaults.hex is added to CBFS only if
CONFIG_WIFI_SAR_CBFS_FILEPATH is not empty because current mainboards
do not provide a default SAR file in
coreboot. Thus, CONFIG_WIFI_SAR_CBFS_FILEPATH is updated to have a
default value of "".
BUG=b:173465272
Cq-Depend: chromium:2757781
Change-Id: I0bb8f6e2511596e4503fe4d8c34439228ceaa3c7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add USB Port into devicetree for storo
BUG=b:177389444
BRANCH=dedede
TEST=built firmware and verified USB3.0 function is OK
Change-Id: I4d5160ff23d2bd386cb33164b580e6d6f3bf30fd
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add camera support in devicetree and associated GPIO configuration.
BUG=b:181729304
BRANCH=dedede
TEST=built blipper firmware and verified camera function is OK
Change-Id: I806ec207a454d4383aca093159553b7e618e16b2
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add audio codec and speaker amplifier support into devicetree
BUG=b:181732574
BRANCH=dedede
TEST=built blipper firmware and verified audio function is OK
Change-Id: Id4633649b5e0595ed99a40ae35eb54b005154604
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add G2 and ELAN touchscreen into devicetree for blipper.
BUG=b:181098785
BRANCH=dedede
TEST=built blipper firmware and verified touchscreen function is ok
Change-Id: Ie0bfc2972fc1a33a6f02495d3976b816209e956b
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Configuring GPP_B7 as GPO_HIGH.
Sasuke doesn't have SAR sensor, GPP_B7 is routed to the LTE module
and is kept high so that the LTE module uses the default emission power.
BUG=b:180492044
BRANCH=firmware-dedede-13606.B
TEST="FW_NAME=sasuke emerge-dedede coreboot"
Change-Id: Ib38c649830db2291b3a2a771f5c884acf37dcbeb
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51049
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some of the temperature sensors defined in baseboard do not exist in
magolor. With the format the DPTF policies are defined in magolor, all
the entries from the baseboard are included and then the overrides
applied. This causes the non-existent DPTF devices to be exported in
the ACPI table and in turn OS reading invalid temperatures. Fix the
format for DPTF passive and critical policies.
BUG=None
BRANCH=dedede
TEST=Build and boot to OS in magolor. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I43f0b188e49e24657db055ce898ce159d499a22e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Some of the temperature sensors defined in baseboard do not exist in
madoo. With the format the DPTF policies are defined in madoo, all the
entries from the baseboard are included and then the overrides applied.
This causes the non-existent DPTF devices to be exported in the ACPI
table and in turn OS reading invalid temperatures. Fix the format for
DPTF passive and critical policies.
BUG=b:182513022
BRANCH=dedede
TEST=Build and boot to OS in madoo. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Idc5d0b357d61b9346b4d20ec8322b124c9655b4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Ben Kao <ben.kao@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This change adds fine-tuned USB2 PHY parameters for sasukette.
BUG=180753635
TEST=Built and verified USB2 eye diagram test result
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I5612e7dcca15b340763dee1475e979ee551a2146
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add LTE module support into devicetree and associated GPIO configuartion.
BUG=b:177955524
BRANCH=dedede
TEST=LTE function is OK
Change-Id: I9aff9608e08eae00ab5ac8547f63bc83b62fea78
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add P-sensor into devicetree for storo according to
configuration information provided by the vendor.
BUG=b:177392203
BRANCH=dedede
TEST=built storo firmware and verified P-sensor function
Change-Id: Iced4ab7d94b38ef8b1807955cbb887454accb1e8
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
Add audio codec and speaker amplifier support into devicetree
BUG=b:179057895
BRANCH=dedede
TEST=audio function is OK
Change-Id: Ia864ac47223adb80463966209f6ff3640b715378
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51003
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To support mipi camera.
1. enable DRIVERS_INTEL_MIPI_CAMERA/SOC_INTEL_COMMON_BLOCK_IPU
2. add IPU/VCM/NVM/CAM1 into devicetree
To support usb camera.
add camera support in devicetree and associated GPIO configuration.
BUG=b:177393430, b:177388006
TEST=Build and boot to OS. Camera function is OK.
Change-Id: I98d5708d1955406c2e46db972903057bb3d12dcc
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50995
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update GPP_A10 and GPP_H17 configuration to meet LTE power sequence
specification.
- FCPO (GPP_A10) should not turned off during warm reset.
BUG=b:177177967
BRANCH=dedede
TEST=Verified LTE power signal waveforms during powering on and off
Change-Id: I469f9c94ebd6bf2b68a0edc74f229158d82d0ef8
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add touchpad into devicetree for blipper.
BUG=b:172787208
BRANCH=dedede
TEST=built blipper firmware and verified touchpad function
the kernel log: found RMI device, manufacturer: Synaptics
Change-Id: I2c9b61ba9d282f994e2f756bafe4af1091d4d617
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51188
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Follow GT7375P Programming Guide_Rev.0.6 to increase
reset delay to 180ms.
2. Add TOUCH_RPT_EN pin(GPP_A11) control to fix TOUCH_RPT_EN pin
keep high after system suspend.
BUG=b:181711141
TEST=Build and boot boten to OS.
Confirm TOUCH_RPT_EN pin keep low after system suspend.
Change-Id: I98efbe68dab538906802647582eba0e068d9c11f
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51254
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure I2C bus 5 high and low time for p-sensor device.
BUG=b:181727056
TEST=Measured the I2C bus frequency reduce to 387 KHz.
Change-Id: I4b6d78d84b8ea145093f52bbb13684e2c6aa979c
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
P-sensor vendor fine-tune detect distance as 20mm for WWAN SAR table switch.
BUG=b:179000150
BRANCH=dedede
TEST=run "i2cdump -y -f 15 0x28" to confirm registers as expected.
un-approach：
=> register address: 0x01 value: 0x00
approach:
=> register address: 0x01 value: 0x02
Confirm WWAN SAR table work as expected.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I659721e60aa0766ed4c277dae43ded222e18ad1c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51343
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the memory parts. The memory parts being added are:
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNBKMMLXR-NEE
BUG=None
TEST=Build the blipper board.
Change-Id: Ia7e4c1d5c06013c1902816d6dcafb5a8a0386bb3
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
There is going to be an upcoming board version for Drawlat/man and
Drawcia. Hence apply the override GPIO table without pad termination for
board versions 6 or 8 alone.
BUG=None
BRANCH=dedede
TEST=Build and boot to OS in Drawcia.
Change-Id: I320de9a0c37ac033f3efda74eeb8f36e34667fd4
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
Configure I2C high / low time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (400 kHz).
Measured I2C frequency just as below after tuning:
touchpad:372 kHz
audio codec RT5682:386.8 kHz
speaker AMP L:387.5 kHz
speaker AMP R:388.9 kHz
BUG=b:181342340
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I05d78c088190e349281a34b2aeed39ae8d867dc2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51112
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ELAN touchscreen into devicetree for storo.
BUG=b:177389448
BRANCH=dedede
TEST=built storo firmware and verified touchscreen function
Change-Id: I0d9e5005928c6fda3d1f0ce8bd9ae135e4a04867
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50981
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:177834652
BRANCH=dedede
TEST=build kracko firmware
Change-Id: I360920f80f4ce5dcbcde25c433e23803fa72569b
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
As per CL:2641346, update GBB flag names:
GBB_FLAG_FORCE_DEV_BOOT_LEGACY -> GBB_FLAG_FORCE_DEV_BOOT_ALTFW
GBB_FLAG_DEFAULT_DEV_BOOT_LEGACY -> GBB_FLAG_DEFAULT_DEV_BOOT_ALTFW
BUG=b:179458327
TEST=make clean && make test-abuild
BRANCH=none
Signed-off-by: Joel Kitching <kitching@google.com>
Change-Id: I0ac5c9fde5a175f8844e9006bb18f792923f4f6d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
GPP_E11 should be configured to be routed via APIC to avoid
p-sensor communication error in OS.
BUG=b:178465379
BRANCH=dedede
TEST=run "i2cdump -y -f 15 0x28" to confirm registers as expected.
un-approach：
=> register address: 0x01 value: 0x00
approach:
=> register address: 0x01 value: 0x02
verify sx932x IRQ in "/proc/interrupts" loading as expected.
Change-Id: I7d639ec1f9b31b240475dc1c8025bf59ae1e8e0b
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50876
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
