| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds the required FMD changes to support the change
in cse_lite 'commit Ie0266e50463926b8d377825 ("remove
cbfs_unverified_area_map() API in cse_lite")' for CBFS verification.
With the change in cse_lite the ME_RW_A/B blobs are now part of
FW_MAIN_A/B and corresponding entries in FMD can be removed for boards
that currently use them.
BUG=b:284382452
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I3ca88fee181f059852923d50292b24c0e5b9fd6d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
It's not needed to put a backslash at the end of a line for quoted
multiline values. Thus, remove it.
Change-Id: I1b83d53598ba2adeed853a96d6c2c1a21f01a9f7
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78576
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Some Type-C monitors do not immediately assert HPD. If we enter FSP-S
before HDP is asserted, display initialisation may fail. So wait for
HPD.
This is similar to commit b40c6009141e ("mainboard/hatch: Fix puff DP
output on cold boots") on puff, except we don't use
google_chromeec_wait_for_displayport() since that EC command was removed
for TCPMv2 (https://crrev.com/c/4221975). Instead we use the HPD signals
only. By waiting for any HPD signal (Type-C or HDMI), we skip waiting if
HDMI is connected, which is the same behaviour as puff and fizz.
BUG=b:303533815
BRANCH=dedede
TEST=On dexi, connect a display via a Type-C to HDMI dongle and check
the dev and recovery screens are now displayed correctly. Also check the
logs in the following cases:
Cold reboot in dev mode, Type-C to HDMI dongle:
HPD ready after 800 ms
Warm reboot in dev mode, Type-C to HDMI dongle:
HPD ready after 0 ms
Cold/warm reboot in dev mode, direct Type-C:
HPD ready after 0 ms
Cold/warm reboot in dev mode, direct HDMI:
HPD ready after 0 ms
Cold/warm reboot in dev mode, no display:
HPD not ready after 3000 ms. Abort.
Change-Id: Ib4fc071cac98a542072ffbeb6943bff4c988554c
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78450
Reviewed-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update Goodix touchpad HID to GDIX0000 for GXTP7288 and GXTP7863.
BUG=b:305118852
BRANCH=firmware-dedede-13606.B
TEST=Build and touchpads are workable
# evtest for GXTP7863
No device specified, trying to scan all of /dev/input/event*
Available devices:
/dev/input/event0: Lid Switch
/dev/input/event1: Power Button
/dev/input/event2: AT Translated Set 2 keyboard
/dev/input/event3: cros_ec_buttons
/dev/input/event4: Elan Touchscreen
/dev/input/event5: GDIX0000:00 27C6:0D51 Mouse
/dev/input/event6: GDIX0000:00 27C6:0D51 Touchpad
# evtest for GXTP7288
No device specified, trying to scan all of /dev/input/event*
Available devices:
/dev/input/event0: Lid Switch
/dev/input/event1: Power Button
/dev/input/event10: GDIX0000:00 27C6:01F5 Touchpad
/dev/input/event11: sof-da7219max98360a Headset Jack
/dev/input/event12: sof-da7219max98360a HDMI/DP,pcm=2
/dev/input/event13: sof-da7219max98360a HDMI/DP,pcm=3
/dev/input/event14: sof-da7219max98360a HDMI/DP,pcm=4
/dev/input/event2: AT Translated Set 2 keyboard
/dev/input/event3: cros_ec_buttons
/dev/input/event4: ELAN900C:00 04F3:2E5D
/dev/input/event5: ELAN900C:00 04F3:2E5D UNKNOWN
/dev/input/event6: ELAN900C:00 04F3:2E5D UNKNOWN
/dev/input/event7: ELAN900C:00 04F3:2E5D Stylus
/dev/input/event8: ELAN900C:00 04F3:2E5D Stylus
/dev/input/event9: GDIX0000:00 27C6:01F5 Mouse
Change-Id: Id2a6223bdbb2f0693149136baa853ca2efb57815
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78503
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Some Type-C monitors do not immediately assert HPD. If we enter FSP-S
before HDP is asserted, display initialisation may fail. So wait for
HPD.
This is similar to commit b40c6009141e ("mainboard/hatch: Fix puff DP
output on cold boots") on puff, except we don't use
google_chromeec_wait_for_displayport() since that EC command was removed
for TCPMv2 (https://crrev.com/c/4221975). Instead we use the HPD signals
only. By waiting for any HPD signal (Type-C or HDMI), we skip waiting if
HDMI is connected, which is the same behaviour as puff and fizz.
TEST=On dibbi, connect a display via a Type-C to HDMI dongle and check
the dev and recovery screens are now displayed correctly. Also check the
logs in the following cases:
Cold reboot in dev mode, Type-C to HDMI dongle:
HPD ready after 800 ms
Warm reboot in dev mode, Type-C to HDMI dongle:
HPD ready after 0 ms
Cold/warm reboot in dev mode, direct Type-C:
HPD ready after 0 ms
Cold/warm reboot in dev mode, direct HDMI:
HPD ready after 0 ms
Cold/warm reboot in dev mode, no display:
HPD not ready after 3000 ms. Abort.
Change-Id: Id4657b5d5a95a68ecbd9efcf3585cf96ad1e13e1
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
Create the dexi variant of the taranza project by
copying the files to a new directory named for the variant.
BUG=b:303533815
BRANCH=dedede
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_DEXI
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: I708a16cb864dca7309cb0201e7887af7456a4885
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78249
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set USB port which corresponds PORTSCN/PORTSCXUSB3 register bits for
enable USB wake.
BUG=b:302230434
TEST=Verify USB-A device could wake up Boxy
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I0f6300dc6bbb6fb8226151e49e38f0450b1e71b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78144
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set USB port which corresponds PORTSCN/PORTSCXUSB3 register bits for enable USB wake.
The physical USB slot is 6, USB2 port5 for Bluetooth, total USB2 port num is 7, USB3 keep 6.
BUG=b:300844110
TEST=Verify USB-A device could wake up Taranza
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ied92c4a70bc594bd189dcb942f1a445412509464
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78068
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: I5527d5968be35f52b912d9d6e1d9f46f24569bbc
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Convert TPM functions to return TPM error codes(referred to as
tpm_result_t) values to match the TCG standard.
BUG=b:296439237
TEST=build and boot to Skyrim
BRANCH=None
Change-Id: Ifdf9ff6c2a1f9b938dbb04d245799391115eb6b1
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77666
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Convert hex print values to use the %#x qualifier to print 0x{value}.
BUG=b:296439237
TEST=build and boot to Skyrim
BRANCH=None
Change-Id: I0d1ac4b920530635fb758c5165a6a99c11b414c8
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78183
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add PLx from JSL PDG (ID: 613095) in taranza devicetree.
Add ramstage.c in Makefile.inc and update Taranza power limits in
taranza ramstage.c.
BUG=b:296004956
TEST=emerge-dedede coreboot and check psys and PLx value on taranza
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Id43bb91bc9efb91cb074b075122cce4f22e0716c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Dedede boards which select AUDIO_AMP_UNPROVISIONED via fw_config use
rt1015 for the speaker topology, not max98360a.
TEST=build/boot Win11 on google/magpie, verify correct audio profile
selected.
Change-Id: I5b75bd8fd37d2837de3c5bd25a02411a6982103b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Make naming convention consistent across all functions return values.
BUG=b:296439237
TEST=Boot to OS on Skyrim
BRANCH=None
Change-Id: If86805b39048800276ab90b7687644ec2a0d4bee
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77536
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Update PLDs to match the port layout:
Front (left to right):
A4, A3, A2
Back (left to right):
C0, A0, A1
BUG=b:264960828
TEST=USB2 and USB3 ports are peered correctly in the kernel:
Before:
$ cd /sys/devices/pci0000:00/0000:00:14.0
$ ls -l $(find . -name peer)
./usb1/1-0:1.0/usb1-port1/peer -> ../../../usb2/2-0:1.0/usb2-port1
./usb1/1-0:1.0/usb1-port2/peer -> ../../../usb2/2-0:1.0/usb2-port2
./usb1/1-0:1.0/usb1-port3/peer -> ../../../usb2/2-0:1.0/usb2-port3
./usb1/1-0:1.0/usb1-port4/peer -> ../../../usb2/2-0:1.0/usb2-port4
./usb1/1-0:1.0/usb1-port5/peer -> ../../../usb2/2-0:1.0/usb2-port5
./usb1/1-0:1.0/usb1-port6/peer -> ../../../usb2/2-0:1.0/usb2-port6
./usb2/2-0:1.0/usb2-port1/peer -> ../../../usb1/1-0:1.0/usb1-port1
./usb2/2-0:1.0/usb2-port2/peer -> ../../../usb1/1-0:1.0/usb1-port2
./usb2/2-0:1.0/usb2-port3/peer -> ../../../usb1/1-0:1.0/usb1-port3
./usb2/2-0:1.0/usb2-port4/peer -> ../../../usb1/1-0:1.0/usb1-port4
./usb2/2-0:1.0/usb2-port5/peer -> ../../../usb1/1-0:1.0/usb1-port5
./usb2/2-0:1.0/usb2-port6/peer -> ../../../usb1/1-0:1.0/usb1-port6
After:
$ cd /sys/devices/pci0000:00/0000:00:14.0
$ ls -l $(find . -name peer)
./usb1/1-0:1.0/usb1-port1/peer -> ../../../usb2/2-0:1.0/usb2-port1
./usb1/1-0:1.0/usb1-port2/peer -> ../../../usb2/2-0:1.0/usb2-port3
./usb1/1-0:1.0/usb1-port3/peer -> ../../../usb2/2-0:1.0/usb2-port4
./usb1/1-0:1.0/usb1-port4/peer -> ../../../usb2/2-0:1.0/usb2-port6
./usb1/1-0:1.0/usb1-port5/peer -> ../../../usb2/2-0:1.0/usb2-port5
./usb1/1-0:1.0/usb1-port7/peer -> ../../../usb2/2-0:1.0/usb2-port2
./usb2/2-0:1.0/usb2-port1/peer -> ../../../usb1/1-0:1.0/usb1-port1
./usb2/2-0:1.0/usb2-port2/peer -> ../../../usb1/1-0:1.0/usb1-port7
./usb2/2-0:1.0/usb2-port3/peer -> ../../../usb1/1-0:1.0/usb1-port2
./usb2/2-0:1.0/usb2-port4/peer -> ../../../usb1/1-0:1.0/usb1-port3
./usb2/2-0:1.0/usb2-port5/peer -> ../../../usb1/1-0:1.0/usb1-port5
./usb2/2-0:1.0/usb2-port6/peer -> ../../../usb1/1-0:1.0/usb1-port4
Change-Id: I682a153d6b757e1b66373c622a6fcfbf389184e3
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77877
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update PLDs to match the port layout:
Front (left to right):
C0, A1, A0
Left side:
C1
Also enable the usb 3.1 device.
BUG=b:264960828
TEST=USB2 and USB3 ports are peered correctly in the kernel:
Before:
$ cd /sys/devices/pci0000:00/0000:00:14.0
$ ls -l $(find . -name peer)
./usb1/1-0:1.0/usb1-port1/peer -> ../../../usb2/2-0:1.0/usb2-port1
./usb1/1-0:1.0/usb1-port3/peer -> ../../../usb2/2-0:1.0/usb2-port3
./usb1/1-0:1.0/usb1-port4/peer -> ../../../usb2/2-0:1.0/usb2-port4
./usb1/1-0:1.0/usb1-port5/peer -> ../../../usb2/2-0:1.0/usb2-port5
./usb1/1-0:1.0/usb1-port6/peer -> ../../../usb2/2-0:1.0/usb2-port6
./usb2/2-0:1.0/usb2-port1/peer -> ../../../usb1/1-0:1.0/usb1-port1
./usb2/2-0:1.0/usb2-port3/peer -> ../../../usb1/1-0:1.0/usb1-port3
./usb2/2-0:1.0/usb2-port4/peer -> ../../../usb1/1-0:1.0/usb1-port4
./usb2/2-0:1.0/usb2-port5/peer -> ../../../usb1/1-0:1.0/usb1-port5
./usb2/2-0:1.0/usb2-port6/peer -> ../../../usb1/1-0:1.0/usb1-port6
After:
$ cd /sys/devices/pci0000:00/0000:00:14.0
$ ls -l $(find . -name peer)
./usb1/1-0:1.0/usb1-port1/peer -> ../../../usb2/2-0:1.0/usb2-port1
./usb1/1-0:1.0/usb1-port2/peer -> ../../../usb2/2-0:1.0/usb2-port3
./usb1/1-0:1.0/usb1-port3/peer -> ../../../usb2/2-0:1.0/usb2-port4
./usb1/1-0:1.0/usb1-port4/peer -> ../../../usb2/2-0:1.0/usb2-port2
./usb1/1-0:1.0/usb1-port5/peer -> ../../../usb2/2-0:1.0/usb2-port5
./usb1/1-0:1.0/usb1-port6/peer -> ../../../usb2/2-0:1.0/usb2-port6
./usb2/2-0:1.0/usb2-port1/peer -> ../../../usb1/1-0:1.0/usb1-port1
./usb2/2-0:1.0/usb2-port2/peer -> ../../../usb1/1-0:1.0/usb1-port4
./usb2/2-0:1.0/usb2-port3/peer -> ../../../usb1/1-0:1.0/usb1-port2
./usb2/2-0:1.0/usb2-port4/peer -> ../../../usb1/1-0:1.0/usb1-port3
./usb2/2-0:1.0/usb2-port5/peer -> ../../../usb1/1-0:1.0/usb1-port5
./usb2/2-0:1.0/usb2-port6/peer -> ../../../usb1/1-0:1.0/usb1-port6
(Ports 5 and 6 are not used on boxy but are peered by default)
Change-Id: I1563d9eaa27353c8c97225a0a6ecc238e9275ce2
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
BUG=b:264960828
TEST=USB2 and USB3 ports are peered correctly in the kernel:
Before:
$ cd /sys/devices/pci0000:00/0000:00:14.0
$ ls -l $(find . -name peer)
./usb1/1-0:1.0/usb1-port1/peer -> ../../../usb2/2-0:1.0/usb2-port1
./usb1/1-0:1.0/usb1-port2/peer -> ../../../usb2/2-0:1.0/usb2-port3
./usb1/1-0:1.0/usb1-port3/peer -> ../../../usb2/2-0:1.0/usb2-port4
./usb1/1-0:1.0/usb1-port4/peer -> ../../../usb2/2-0:1.0/usb2-port5
./usb1/1-0:1.0/usb1-port5/peer -> ../../../usb2/2-0:1.0/usb2-port6
./usb2/2-0:1.0/usb2-port1/peer -> ../../../usb1/1-0:1.0/usb1-port1
./usb2/2-0:1.0/usb2-port3/peer -> ../../../usb1/1-0:1.0/usb1-port2
./usb2/2-0:1.0/usb2-port4/peer -> ../../../usb1/1-0:1.0/usb1-port3
./usb2/2-0:1.0/usb2-port5/peer -> ../../../usb1/1-0:1.0/usb1-port4
./usb2/2-0:1.0/usb2-port6/peer -> ../../../usb1/1-0:1.0/usb1-port5
After:
$ cd /sys/devices/pci0000:00/0000:00:14.0
$ ls -l $(find . -name peer)
./usb1/1-0:1.0/usb1-port1/peer -> ../../../usb2/2-0:1.0/usb2-port1
./usb1/1-0:1.0/usb1-port2/peer -> ../../../usb2/2-0:1.0/usb2-port3
./usb1/1-0:1.0/usb1-port3/peer -> ../../../usb2/2-0:1.0/usb2-port4
./usb1/1-0:1.0/usb1-port4/peer -> ../../../usb2/2-0:1.0/usb2-port6
./usb1/1-0:1.0/usb1-port5/peer -> ../../../usb2/2-0:1.0/usb2-port5
./usb2/2-0:1.0/usb2-port1/peer -> ../../../usb1/1-0:1.0/usb1-port1
./usb2/2-0:1.0/usb2-port3/peer -> ../../../usb1/1-0:1.0/usb1-port2
./usb2/2-0:1.0/usb2-port4/peer -> ../../../usb1/1-0:1.0/usb1-port3
./usb2/2-0:1.0/usb2-port5/peer -> ../../../usb1/1-0:1.0/usb1-port5
./usb2/2-0:1.0/usb2-port6/peer -> ../../../usb1/1-0:1.0/usb1-port4
Change-Id: I5fe8066e361da62b747464b2ec09bcc6e7dda0fe
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77867
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Update the dibbi ec.h so that it's correct for a chromebox. Remove
everything related to:
- Lid
- Battery
- Built-in keyboard
- AC connect/disconnect
- Mode changes
BUG=b:294963793
TEST=Boot dibbi and check the APCI tables no longer contain lid and PS/2
keyboard devices.
Change-Id: Idfa5adcec308d68555d292fddc1db43c9a64d649
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77863
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Dibbi variants are chromeboxes, so they need different settings in ec.h.
Add a new dibbi baseboard ec.h and use it for dibbi variants. For now
it's identical to the dedede baseboard ec.h. It will be updated in the
following CL.
BUG=b:294963793
TEST=With the following CL, boot dibbi and check the APCI tables no
longer contain lid and PS/2 keyboard devices.
Change-Id: I4075041ab8f02026623d1a26a555bee5eb09e77b
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77782
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
|
|
Add FW_CONFIG probe for absent FIVR bypass mode on peezer.
BUG=b:296982082
BRANCH=firmware-dedede-13606.B
TEST=emerge-dedede coreboot chromeos-bootimage
Change-Id: I0b2053b2d732fd9462686ed7b0c9225539b28fb2
Signed-off-by: Daniel_Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77396
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:297276380
BRANCH=dedede
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot
chromeos-bootimage
Cq-Depend: chrome-internal:6373154
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: If21c7a7d329b0b1cc2c73dadb0c5b8a5b8ab27e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77399
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
|
|
Enable bit 9 for 100M mode green LED blink.
Reference:
- RTL8111H-CG Datasheet 1.92 section 7.2 for customizable led configuration
BUG=b:293983804
TEST=emerge-dedede coreboot and verify LAN LED behavior
Change-Id: Ice5686affcc014a2dfd35b7f579c8eaa38c2d3fe
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77393
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
This change are added fine-tuned USB2 PHY parameters to improve the
USB2 eye diagram result.
BUG=b:296493887
BRANCH=firmware-dedede-13606.B
TEST=Local build bios successfully.
And verified the USB2 eye diagram test result.
Change-Id: I915fe689883267901e8faba28632345d8c227c28
Signed-off-by: Daniel_Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77359
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for ACPI display brightness controls, so that panel
adjustment is available under Windows.
TEST=build/boot Win11 on google/magpie, verify panel brightness
controls available and functional.
Change-Id: I66daa6bbca15046994dff83bee6e7cf99aae0b33
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77271
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update DPTF thermal settings from thermal team suggestion:
1. Modify CPU passive policy to 95.
2. Modify TS0/TS1/TS2 passive policy to 90 for CPU.
3. Modify TS1 passtve policy watt to 6w.
4. Modify TS0/TS1/TS2 critical policy to 100.
BUG=b:294479707
TEST=Build and verify DPTF value by thermal team on Boxy system
Change-Id: Ic34e44f218ff980c54bf93841880fab5e21b3fca
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77108
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Generate RAM ID for CXMT CXDB4ABAM-ML
DRAM Part Name ID to assign
CXDB4ABAM-ML 1 (0001)
BUG=b:290154780
BRANCH=dedede
TEST=FW_NAME=boxy emerge-dedede coreboot chromeos-bootimage
Change-Id: Ide44acf6bb8e5d5023c76d9e5e48ef113f7c6ec6
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76825
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Add ramstage.c in Makefile.inc and update boxy power limits in
Boxy ramstage.c.
BUG=b:290293153
TEST=emerge-dedede coreboot and check psys and PLx value on boxy
Change-Id: I4257dab358f066ebd13b6f251e8a5258a72fbd39
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76877
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To help identify the licenses of the various files contained in the
coreboot source, we've added SPDX headers to the top of all of the
.c and .h files. This extends that practice to Makefiles.
Any file in the coreboot project without a specific license is bound
to the license of the overall coreboot project, GPL Version 2.
This patch adds the GPL V2 license identifier to the top of all
makefiles in the mainboard directory that don't already have an SPDX
license line at the top.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ic451e68b1ad9ccdf34484dd98bd7fca7e177ef22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68982
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
BUG=b:279097356
TEST=On dibbi:
- flash OS 15449.0.0 (where suspend is broken due to b:274531972)
- run `suspend_stress_test --count=1 --suspend_max=30 --suspend_min=28`
- check the AP wakes up immediately when the EC detects a sleep hang
Change-Id: I24a2aa5de1f76e6dd1c1ce726b648583756e5e55
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76938
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add PLx from JSL PDG(ID: 613095) in boxy devicetree.
BUG=b:290293153
TEST=emerge-dedede coreboot and read correct value on boxy CPU log:
CPU TDP = 6 Watts, CPU PL4 = 60 Watts
Change-Id: I7b063dc235fb714ba47eb620b914f2f9e92a2715
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76876
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add the new memory support:
Samsung K4U6E3S4AB-MGCL
BUG=b:294151054
BRANCH=firmware-dedede-13606.B
TEST=Run command "go run ./util/spd_tools/lp4x/gen_part_id.go JSL lp4x \
src/mainboard/google/dedede/variants/pirika/memory/ \
src/mainboard/google/dedede/variants/pirika/memory/\
mem_parts_used.txt"
Change-Id: Ief9bbf11fc05c8155f1da7188926a29dbbfbe488
Signed-off-by: Daniel_Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76542
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for Samsung K4U6E3S4AB-MGCL.
BUG=b:293240969
TEST=emerge-dedede coreboot
Change-Id: I92a1f2110e74b5d25572e0e86e04b5b32112c1f5
Signed-off-by: tongjian <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add new memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
1. H54G56CYRBX247
2. H9HCNNNCPMMLXR-NEE
3. MT53E1G32D2NP-046 WT:B
4. K4UBE3D4AB-MGCL
5. K4UBE3D4AA-MGCR
BUG=b:290811418
BRANCH=dedede
TEST=FW_NAME=cret emerge-dedede coreboot chromeos-bootimage
Change-Id: Ib7f23dc3604fe1869772d92c9d7b8cc32ed9bbb9
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Mapping to the fw_config of AUDIO_AMP in dedede,
and set new AUDIO_AMP configuration of ALC5650 as value 4.
BUG=b:284060672
BRANCH=dedede
TEST=build pass
Change-Id: Ic3dccd09d3ba1619cce2ac0d5f123badbeeaccdc
Signed-off-by: Daniel_Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
ALC5682-VD/ALC5682I-VS load different kernel driver by different hid
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:290876132
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Change-Id: Id5e0ba7a4ca57e311465ba8e74105f5ee7b8ee8a
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76435
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- remove usb2_ports[5] since taranza doesn't have PL2303.
- add usb2_ports[6] and usb3_ports[1] for Type-A Port A4.
BUG=b:288094807, b:278167978
TEST=emerge-dedede coreboot chromeos-bootimage
verified all the USB port works
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I7b411c21271497ba386143140aa8cfbb17a1a111
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76186
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The taranza removed the APW8738BQBI and "disable_external_bypass_vr" should be set to "1" to disable.
BUG=b:288978340
TEST=emerge-dedede coreboot
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I0a849fbfacba1d200c969c66bb058863d7ab3085
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add ramstage.c in Makefile.inc and update Dibbi power limits in
Dibbi ramstage.c.
BUG=b:281479111
TEST=emerge-dedede coreboot and check psys and PLx value on dibbi
Signed-off-by: Chia-Ling Hou <chia-ling.hou@intel.com>
Change-Id: Ieaff856b762b546f3e99acb7ba2ce15791193da6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75681
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With newer dedede design, it's required to config corresponding
psyspmax, psyspl1, psyspl2, pl1 and pl2 by different kinds of
adapter.
BUG=b:281479111
TEST=emerge-dedede coreboot and check correct value on dibbi
Signed-off-by: Chia-Ling Hou <chia-ling.hou@intel.com>
Change-Id: I583c930379233322c41027805369f81d02000ee7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75680
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
1.Add Codec ALC5650 setings for drivers/i2c/generic
2.Add option value '3' to AUDIO_CODEC_SOURCE for SSFC
BUG=b:284060672
BRANCH=master
TEST=emerge-dedede coreboot chromeos-ec chromeos-bootimage
Confirm the device is existed on system.
Change-Id: I39703a950620c90aa3740b7313b7d32cc68eede4
Signed-off-by: Daniel_Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75918
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
|
|
Add JSL SKUs ID and add PLx from JSL PDG in project devicetree.
BUG=b:281479111
TEST=emerge-dedede coreboot and read correct value on dibbi
Signed-off-by: Chia-Ling Hou <chia-ling.hou@intel.com>
Change-Id: Ic086e32a2692f4f5f9b661585b216fa207fc56fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75679
Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com>
Reviewed-by: Super Ni <super.ni@intel.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Boxy audio codec chip uses ALC5682I-VD, not ALC5682I-VS.
It needs to modify codec HID to "10EC5682" in coreboot to fix audio no
output sound issue.
BUG=b:286970886
BRANCH=dedede
TEST=confirm audio soundcard can be list by command "aplay -l"
Change-Id: Icd69a9d757ba817b586a703a17375682db684224
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts.
The memory parts being added are:
1. K4U6E3S4AB-MGCL
2. K4UBE3D4AB-MGCL
BUG=b:285504022
BRANCH=dedede
TEST=build
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I87a4dcdb6196c3ca7bed4b5c1bc654297339c16d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75605
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Incorrect filename "MakeFile.inc" cause gpio.c can not be complied.
Rename to "Makefile.inc" and confirm gpio.c can load correctly.
BUG=b:281620454
BRANCH=dedede
TEST=build and confirm gpio.c can be loaded
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: I39947c66de04695e5242ab1affc328894f34f9f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75520
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
copy from dibbi since taranza base on dibbi,this is only for first
initial configuration, will update the more setting afterward.
BUG=b:277664211
BRANCH=dedede
TEST=build
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ia319f65897c0fea2f0558c20a5bc36bb6fbaea96
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts.
BUG=b:277664211
BRANCH=dedede
TEST=build
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I6bbb67ccdd8ebc21719921d00320907f8dbb285f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74933
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The boxy removed the APW8738BQBI-TRG and
"disable_external_bypass_vr" should be set to "1" to disable
BUG=b:271407334
TEST=emerge-dedede coreboot
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: Ic6667e93de41e84f67363ab7554fe755fe50684a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74889
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create overridetree and GPIO config based on latest schematic:
1. Update PCIe ports
2. Update USB ports
3. Remove unused I2Cs
4. Remove unused peripherals (SD card, eDP, speakers)
5. Add LAN
6. Thermal policy for updated temp sensors
BUG=b:277529068
BRANCH=dedede
TEST=build
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: I5a155ebca50dbd5bdb046713ebabbee395361273
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74626
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add all SOF chip drivers to baseboard and use FW_CONFIG to determine
the correct option, to ensure the correct audio config is passed to the
SOF OS drivers.
TEST=build, boot Windows on several dedede variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: I9452b11af614d8727aa8dd448e37f7a06faa450d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74818
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add boxy supported memory parts in mem_parts_used.txt, generate
SPD id for this part.
1. Samsung K4U6E3S4AB-MGCL
2. Hynix H54G46CYRBX267
3. Micron MT53E512M32D1NP-046 WT:B
BUG=b:278983561
TEST=Use part_id_gen to generate related settings
Signed-off-by: kevin3.yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: I317f2b31774627706babdea10776af05ab692d1e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Create the boxy variant of the waddledee reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:277529068
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_BOXY
Change-ID: Ief22eb000421c23abf6de3f99eb860bdae1e7919
Signed-off-by: kevin3.yang <kevin3.yang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: Ie75ce1eee3179a623da812a6b76c7ec457684177
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Add boten supported memory parts in mem_parts_used.txt, generate
SPD id for this part.
1. Samsung K4U6E3S4AB-MGCL
BUG=b:278138388
TEST=Use part_id_gen to generate related settings
Signed-off-by: kevin3.yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: I5f910393847c6494f77c009cb11f50b31bebffb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add G2touch touchscreen support for kracko.
BOE NV116WHM-T04 V8.0 with G7500 touch panel sensor IC
BUG=b:277852921
BRANCH=firmware-dedede-13606.B
TEST=emerge-dedede coreboot & test on DUT
Change-Id: Ic065d5dc2900c6ccfee09031f7a80cefc391f5dd
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74307
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the taranza variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:277664211
BRANCH=dedede
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_TARANZA
Change-Id: Id64e48ff2acd6e827fe586a00376183930ddc7e1
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74295
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ALC5682-VD/ALC5682-VS use different kernel driver by different hid name.
Update hid name depending on the AUDIO_CODEC_SOURCE field of fw_config.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:275644832
TEST=emerge-dedede coreboot
BRANCH=firmware-dedede-13606.B
Change-Id: I644f3aa3187e08146d78abb70a568833bc9b9211
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add FW_CONFIG probe for absent ANPEC APW8738BQBI IC on magolor.
BUG=b:223687184
TEST=emerge-dedede coreboot chromeos-bootimage and pass suspend_test and
firmware_ConsecutiveBoot test
Change-Id: I47ad313c4a14edb687913698986df9ece6cd721d
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73833
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adding EC_HOST_EVENT_PANIC to SCI mask allows the EC to interrupt the
Kernel when an EC panic occurs. If system safe mode is also enabled
on the EC, the kernel will have a short period to extract and save info
about the EC panic.
BUG=b:268377440
BRANCH=firmware-dedede-13606.B
TEST=Observe kernel ec panic handler run when ec panics
Change-Id: I24f929ae60a406d0091956dc6cab3e2876ca23e9
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Configure the I2C bus high and low time for audio.
BUG=b:271804915
BRANCH=dedede
TEST=Build and confirm I2C clock for audio is between 380 kHz and 400
kHz
Change-Id: I2987a39abc5527844424edfa1cf70d5c5cea5357
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Add new memory parts in memory_parts_used.txt and generate SPD id for
these parts:
Hynix H54G46CYRBX267
Samsung K4U6E3S4AB-MGCL
BUG=b:272173189
TEST=run part_id_gen to generate SPD id
Change-Id: I141bda6eda3f658ca608c86ad0b320d018598514
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73554
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:269786649
TEST=build and test USB2 port function works fine
BRANCH=dedede
Change-Id: I63928a0d8ce6b2365250fd96572f4a2db948c19d
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
USB2 port 6 may be used for a PL2303 USB to UART bridge, so enable the
port.
BUG=b:269690930
TEST=kernel can detect a PL2303 USB device
BRANCH=dedede
Change-Id: I0ba421c3a502e69d101de40bbd31122211d3fb05
Signed-off-by: Sam McNally <sammc@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
|
|
Enable HDA device and update jack codec HID from ALC5682I-VD to
ALC5682I-VS.
BUG=b:268309238
TEST=kernel detects audio DSP and rt5682s
BRANCH=dedede
Change-Id: Icd17d5009ab8ef4711bb6c5fa414a8188fc0912f
Signed-off-by: Sam McNally <sammc@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Config GPP_B9 as LAN_CLKREQ_ODL based on latest schematic
BUG=265021899
BRANCH=dedede
TEST=emerge-dedede coreboot
Change-Id: Ia099bd64364b46240e0426aa57dfe8d230e7494d
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Liam Flaherty <liamflaherty@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Found-by: linter
Change-Id: I7c6d0887a45fdb4b6de294770a7fdd5545a9479b
Signed-off-by: Alexander Goncharov <chat@joursoir.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72795
Reviewed-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create overridetree and GPIO config based on latest schematic:
1. Update PCIe ports
2. Update USB ports
3. Remove unused I2Cs
4. Remove unused peripherals (SD card, eDP, speakers)
5. Add LAN
6. Thermal policy for updated temp sensors
BUG=b:260934185, b:260934719
BRANCH=dedede
TEST=build
Change-Id: I4789be2eee1d01288031bc1e8ee5c9d6df71f9fe
Signed-off-by: Liam Flaherty <liamflaherty@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71882
Reviewed-by: Adam Mills <adamjmills@google.com>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Exposing the GPIOs via an ACPI PowerResource and the _CRS results in the
OS driver and ACPI thinking they own the GPIO. This can cause timing
problems because it's not clear which system should be controlling the
GPIO.
Previously, we flagged as an error any device which set the
'has_power_resource' flag but did not set 'disable_gpio_export_in_crs.'
There's no reason to require explicit disablement however, so drop the
superfluous 'disable' flag, and change the _CRS generation to check if
the GPIOs will be exported via the 'has_power_resource' flag instead.
BUG=b:265055477
TEST=build/boot skyrim, dump SSDT and verify touchscreen GPIOs only
listed under PRx, not under _CRS.
Change-Id: I837ae6c6fe4b8e1c4e10686406cba06bdb7759d2
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts.
BUG=b:260934724, b:255447299
BRANCH=dedede
TEST=build
Change-Id: I8c95ced79e14bb4a99aa1fa5f4fc3bc0681cc1cc
Signed-off-by: Liam Flaherty <liamflaherty@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71710
Reviewed-by: Adam Mills <adamjmills@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that power sequencing has been implemented, switch from using ACPI
"probed" flag to "detect" flag for all i2c touchscreens. This removes
non-present devices from the SSDT and relieves the OS of the burden of
probing.
BUG=b:121309055
TEST=build/boot Windows/linux on multiple dedede variants, verify all
touchscreens functional in OS, dump ACPI and verify only i2c devices
actually present on the board have entries in the SSDT.
Change-Id: I91e03bd1d96a6b2f0c3813665910133db0d6c308
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
The GPIOs themselves are configured as level triggered, and the drivers
(both Linux and Windows) work better with LEVEL vs EDGE triggering.
TEST=tested with rest of patch train
Change-Id: I212533ffdfb05f841e722c130b52c2976272e670
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
For touchscreens on dedede variants, drive the enable GPIO high
starting in romstage, then disable the reset GPIO in ramstage. This will
allow coreboot to detect the presence of i2c touchscreens during ACPI
SSDT generation (implemented in a subsequent commit).
Since the fast majority of dedede variants have a touchscreen option,
and those that do use the same GPIOs for enable/reset, set the GPIOs for
touchscreen operation in the baseboard and then override for the few (3)
variants that do not have a touchscreen.
BUG=b:121309055
TEST=tested with rest of patch train
Change-Id: Ib95e23545cc3e8589ddbd9e18cd0533bec9333e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Add method variant_romstage_gpio_table() with empty weak implementation
to allow variants to override as needed for touchscreen power
sequencing (to be implemented in a subsequent commit). Call method
in romstage to program any GPIOs the variant may need to set.
TEST=tested with rest of patch train
Change-Id: Ic216827a4b53d1d35913efca63a43d4672791c54
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Create the dibbi variant of the waddledee reference board by
copying the template files to a new directory.
BUG=b:260934018
BRANCH=dedede
TEST=util/abuild/abuild -p none -t google/dedede -x -a includes
GOOGLE_DIBBI
Change-Id: I3b8d4e7f8a53323f56567cbbc03bab7f8804f286
Signed-off-by: Liam Flaherty <liamflaherty@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71709
Reviewed-by: Adam Mills <adamjmills@google.com>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The currently assigned ACPI HID 'PNP0C50' is not a valid per Windows
WHQL validation tests. To ensure compatibility with both Windows and
Linux, set the HID to 'SYNA0000' and CID to 'ACPI0C50' as previously
done for other boards (eg, google/lulu).
TEST=boot Linux 5.1x, Windows 10 on drawcia, verify all touchpad
functions work correctly.
Change-Id: I43eb5bc394a3fbfd4109f2e6c274ec66fc01d46d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
<device/mmio.h>` chain-include `<arch/mmio.h>:
https://doc.coreboot.org/contributing/coding_style.html#headers-and-includes
Also sort includes while on it.
Change-Id: Ie62e4295ce735a6ca74fbe2499b41aab2e76d506
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This change disables unused PCIE RP8 and CLKSRC4. Without this change
sasukette cannot enter into s0ix properly.
BUG=b:259891452
TEST=Build and verified in sasukette
Change-Id: I61bcefa128d4f39613a760b647048f9e19e262c2
Signed-off-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Maulik Vaghela <maulikvaghela@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
EC_HOST_EVENT_USB_CHARGER is no longer defined by the EC, so remove all
references.
BUG=b:216485035,b:258126464
BRANCH=none
TEST=none
Change-Id: I9e3e0e9b45385766343489ae2d8fc43fb0954923
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
SX9324 driver is updated per Linux's documentation found at
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml
Supporting logic for the deprecated SX932x driver is hence guarded by
DRIVERS_I2C_SX9324_SUPPORT_LEGACY_LINUX_DRIVER
This patch by itself does not introduce functional changes to any board.
The legacy SX932x Linux driver never reached upstream Linux and is only
available in ChromeOS kernel fork of 4.4 and 5.4. Linux later accepted
a different implementation named SX9324 and has been available since
5.4. Ideally all variants should adopt the new driver; however, during
the transition phase, coreboot must support both drivers. It is better
to have a single firmware build that can work with both Linux kernel
drivers by specifying both sets of properties. Legacy driver support
should be deleted once all variants finish migration.
BUG=b:242662878
TEST=Dump ACPI SSDT then verify _DSD entries related to the legacy
SX932x driver are identical w/ and w/o this patch
(Tested on Craask and Nivviks)
Change-Id: I42cd6841c3a270c242ed2e739db245e858eadb3b
Signed-off-by: Victor Ding <victording@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69192
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Only a subset of variants has proximity sensors.
This patch by itself does not introduce functional changes to any board.
It is mainly to ease migrating SX9324 from the legacy driver to the
linux one - allowing gradual migration variant by variant.
BUG=b:242662878
TEST=Dump ACPI SSDT then verify they are identical w/ and w/o this patch
Change-Id: Ic00e0d9eafcef2c9eaf32571fecf6190777cec36
Signed-off-by: Victor Ding <victording@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69191
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add VBT data files, ensure secondary VBTs compiled in as needed,
select INTEL_GMA_HAVE_VBT.
TEST=build/boot drawcia, mangolor variants with FSP/GOP display
init and edk2 payload
Change-Id: I58a2ed59bd858ce772e92f6659d341036823b11a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change disables unused PCIE RP8 and CLKSRC4. Without this change
storo cannot enter into s0ix properly.
BUG=b:219376808
TEST=Built and verified in storo
Change-Id: I9867825ce53de72ef73920c153002bc3be4dbd2d
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.corp-partner.google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Maulik Vaghela <maulikvaghela@google.com>
Reviewed-by: Aamir Bohra <aamirbohra@google.com>
|
|
Remove the ACPI ALS device from the EC configuration for newer devices,
because some do not have light sensors, and those who do have their ALS
presented through the new EC sensor interface already.
Inspired from commit ("f13e2501525f ("UPSTREAM: mainboard/google/eve: Remove ACPI ALS device")
BUG=b:253967865
BRANCH=none
TEST=Boot a device and ensure that 'acpi-als' device is not present
in /sys/bus/iio/devices.
Change-Id: Ibcfa9e8c5a4679d557150998fd255789d3f8a272
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68493
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update SoC GPIO setting of camera according to beadrix schematics.
GPP_D13 : NC -> PLTRST (EN_PP2800_CAMERA)
BRANCH=dedede
BUG=b:247178737,b:244120730
TEST=on beadrix, validated by beadrix seconds_system_resume < 500 ms.
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: Id00cb85cdad900c03842ad69707966aa62410efd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com>
Reviewed-by: Simon Yang <simon1.yang@intel.com>
Reviewed-by: Ivan Chen <yulunchen@google.com>
Reviewed-by: Maulik Vaghela <maulikvaghela@google.com>
|
|
Allows dedede boards to use coreboot-generated FMAP layout
when building for non-ChromeOS target.
TEST=build/boot dedede with edk2 payload, non-ChromeOS build
Change-Id: Icb975455cde0d75a5af9130ba3e82a4fb0df5613
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
ALC5682-VD/ALC5682I-VS load different kernel driver by different hid
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config. Define FW_CONFIG bits 41 - 43 (SSFC bits 9 - 11)
for codec selection.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:244620955
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ia6cb56e76bc4e245a32f29b19226fa4fae330c92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Maulik Vaghela <maulikvaghela@google.com>
|
|
Rename variant_base_gpio_table() to baseboard_gpio_table(), since the
GPIO table comes from the baseboard, and is overridden by a separate
table from the variant.
Drop the __weak qualifier as this function is not overridden.
Change-Id: I11814016d654bc2c2e6d24b3d18fb30d5b843fe9
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BIOS_ERR is inappropriate since the init message is informational.
Use BIOS_INFO instead.
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I6fc15291a6d177a1b9e258d08e165224e5e10b32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67733
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch makes dedede EC wake up AP from s0ix when the state of
charge drops to low_battery_shutdown_percent.
Demonstrated as follows:
1. Boot OS.
2. Run powerd_dbus_suspend.
3. On EC, run battfake 4.
4. System resumes.
BUG=b:244253629
TEST=Verified on dedede
Change-Id: I39234d2b9e739383b5f96be49077f8c9831fa0fa
Signed-off-by: Ivan Chen <yulunchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add a variant specific S0ix hook to fill the SSDT table to disable and
enable camera during suspend and resume respectively.
BUG=b:206911455
TEST=Build Boten BIOS image. Ensure that camera is disabled during
suspend and enabled during resume.
Change-Id: I3229b22b8d8651bf2d9df25b10ce6749efde7cf6
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Maulik Vaghela <maulikvaghela@google.com>
|
|
Turn off the LAN power which is controlled by GPP_A10 in S0ix states.
For an USB device, the S0ix hook is needed for the on/off operationas
to take place.
BUG=b:245426120
BRANCH=firmware-dedede-13606.B
TEST=emerge-shotzo coreboot
check LAN LED off in S0ix states
check LAN function ok after suspending 500 loops
check SSDT table has MS0X entry
Scope (\_SB)
{
Method (MS0X, 1, Serialized)
{
If ((Arg0 == One))
{
\_SB.PCI0.CTXS (0x41)
}
Else
{
\_SB.PCI0.STXS (0x41)
}
}
}
Change-Id: I3fcab4a73239b4f006839c0c81e9b4cc74047b77
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:245426120
BRANCH=firmware-dedede-13606.B
TEST=emerge-dedede coreboot
check SSDT table has MS0X entry
Scope (\_SB)
{
Method (MS0X, 1, Serialized)
{
If ((Arg0 == One)) {}
Else
{
}
}
}
Change-Id: Id01089531503e62231c5ab19e4cd8056198b9acb
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Config I2C high / low time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (400 kHz).
EE measured touchscreen/audio runs at 385.5/397.9kHz after tuning.
BUG=b:244403643
BRANCH=firmware-dedede-13606.B
TEST=Build and check after tuning I2C clock is under 400kHz
Change-Id: I7d9503e5f92295432e31f09ae791eaa18eac9d4d
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
Historically, ChromeOS devices have worked around the problem of OEMs
using several different parts for touchpads/touchscreens by using a
ChromeOS kernel-specific 'probed' flag (rejected by the upstream kernel)
to indicate that the device may or may not be present, and that the
driver should probe to confirm device presence.
Since c636142b, coreboot now supports detection for i2c devices at
runtime when creating the device entries for the ACPI/SSDT tables,
rendering the 'probed' flag obsolete for touchpads. Switch all touchpads
in the tree from using the 'probed' flag to the 'detect' flag.
Touchscreens require more involved power sequencing, which will be done
at some future time, after which they will switch over as well.
TEST: build/boot at least one variant for each baseboard in the tree.
Verify touchpad works under Linux and Windows. Verify only a single
touchpad device is present in the ACPI tables.
Change-Id: I47c6eed37eb34c044e27963532e544d3940a7c15
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67305
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:244373677
BRANCH=firmware-dedede-13606.B
TEST=Build image and verified by thermal team.
Change-Id: I8415e0d25a79764f0c1d11688728b7caa3b3d6a4
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
The current reset delay is not enough to make touchscreen IC ready,
ILITEK feedback their requiremt is 400ms in spec T2.
After changing the reset_delay_ms and check touchscreen works,
ILITE also change the IRO to low level trigger.
This CL is to reflect that.
BUG=b:235929123
BRANCH=firmware-dedede-13606.B
TEST=check touchscreen function work
Change-Id: I126b2d74c1d7a1799e2f67a8ab01cba074447c06
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
It is highly unlikely that the "OEM revision" of the DSDT is 0x20110725
on mainboards with a chipset not yet released on 2011-07-25. Since this
comment is most likely to have been copy-pasted from other boards, drop
it from boards which use a chipset newer than Sandy/Ivy Bridge.
Change-Id: If2f61d09082806b461878a76b286204ae56bf0eb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
These comments don't add much value, so remove them.
Change-Id: I7e9692e3fe82345cb7ddcb11c32841c69768cd36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66713
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Update SoC GPIO setting of unused DMIC channel according to beadrix
schematics.
GPP_S2 : NF2 -> NC (DMIC1_CLK)
GPP_S3 : NF2 -> NC (DMIC1_DATA)
BUG=b:203113413, b:237224862
BRANCH=None
TEST=on beadrix, validated by beadrix's DMIC working properly.
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: Ibe2f432cd74b546218ff4ee6e428e9eed9ac611f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivan Chen <yulunchen@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add wifi sar for oscino
BUG=b:240373077
BRANCH=dedede
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede
coreboot-private-files-baseboard-dedede
coreboot
chromeos-bootimage.
Cq-Depend: chrome-internal:4893022
Change-Id: I44cbe8ee08d6136ed116623046893c9749795e50
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66176
Reviewed-by: Ivan Chen <yulunchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update SoC GPIO setting of adding BC1.2 SLGC55545 according to beadrix
schematics.
GPP_A18 : NC -> NF1 (USB_OC0_N)
BUG=b:214393595, b:226294980
BRANCH=None
TEST=on beadrix, validated by beadrix's Type A working properly.
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: I746931582cc12f49f7f1c667563350ebac8ddfa1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com>
Reviewed-by: Ivan Chen <yulunchen@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
