Age | Commit message (Collapse) | Author |
|
Replace i2c driver for the SX9324 proximity detector device.
This is first draft settings, will modify it after fine tuning.
BUG=b:175932166
BRANCH=dedede
TEST=run "i2cdump -y -f 15 0x28" to confirm registers as except.
un-approach:
=> register address: 0x01 value: 0x00
approach:
=> register address: 0x01 value: 0x02
Change-Id: I0c8b5948266a07092799c6db556383fa08b924e6
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update ELAN i2c-hid touchscreen configuration
BUG=b:172517685
BRANCH=dedede
TEST=Verify touchscreen is working fine on botenflex
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Ia7c81fd0a772968ec32406f1e366a90481fc5ad8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:168783630
TEST=Measured the I2C bus frequency reduce to 387 KHz.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I37403dd3ac3c9320398207d2111e1ddb73d6a130
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update devicetree and gpio driving of boten that enable stylus
PEN detect signal is not dual-routed on Boten. Since the gpio_keys kernel
driver expects the pad to be owned by GPIO controller (i.e. configured for
GPIO IRQ), it cannot be configured for ACPI (i.e. SCI).
Thus, this change updates the GPIO configuration for GPP_C12 to
PAD_CFG_GPI_GPIO_DRIVER and device tree entry for PENH device to
use WAKEUP_ROUTE_GPIO_IRQ. Additionally, the signal is marked as active
low in the device tree entry to indicate to the kernel driver that the signal
is inverted.
Not dual routing the signal results in wake source not being added to
eventlog when pen removal results in wake from S0ix.
BUG=b:160752604
BRANCH=dedede
TEST=Build and check behavior is expected.
Signed-off-by: rasheed.hsueh <rasheed.hsueh@lcfc.corp-partner.google.com>
Change-Id: I74a17088da64c22ef1c74d201c80274fc65a44c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=emerge-dedede coreboot
Change-Id: I9d8fa57ae0f554896a4a0722e3e89567676382d4
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
LTE module used in boten has a specific power on/off sequence.
GPIOs related to power sequnce are:
* GPP_A10 - LTE_PWR_OFF_R_ODL
* GPP_H17 - LTE_RESET_R_ODL
1. Power on: GPP_A10 -> 20ms -> GPP_H17
2. Power off: GPP_H17 -> 10ms -> GPP_A10
3. Warm reset: Power off -> 500ms -> Power on
Configure the GPIOs based on these requirements.
BUG=b:163100335
TEST=Build and boot Boten to OS. Ensure that the LTE module power
sequence requirements are met.
Change-Id: Ic6d5d21ce5267f147b332a4c9b01a29b3b8ccfb8
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peichao Wang <pwang12@lenovo.corp-partner.google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add devicetree and device ID for P-sensor
BUG=b:161217096
BRANCH=NONE
TEST=We can get the data from P-sensor if touch the SAR antenna.
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: I70f303995b106cca9758b36ebcde112ebcc90950
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update devicetree of boten that enable stylus
BUG=b:160752604
BRANCH=NONE
TEST=build bios and verify function for boten
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: Ifbcac18fcf758f3d870a6af0d1b03e34369414c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add trackpad, touchscreen, and usb port to devicetree
BUG=b:160664447
BRANCH=NONE
TEST=build bios and verify theirs function for boten
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: I057f7d15d20d1a78acd733cc5463357e9c87afb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add configuration for ALC5682 headphone jack and ALC1015 speaker
amplifier. Also turn on the HDA PCI device.
BUG=b:161667665
TEST=Build the boten board and verified the audio functionality.
Change-Id: I835db854543e6282c102c86a7073b432fd89d0a5
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44920
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add initial support for boten variant board.
BUG=b:158023819
BRANCH=None
TEST=build
Change-Id: I56fe901c6aec781fac217ab08f7583cc25788688
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
|