Age | Commit message (Collapse) | Author |
|
Early JSL silicon hang while booting Linux with ISST enabled. The
malfunctioning silicon revisions have been used only for development
purposes and have been phased out. Thus, drop the ISST workaround.
Change-Id: Ic335c0bf03a5b07130f79c24107a1b1b0ae75611
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This change switches all mainboard devices to use drivers/wifi/generic
instead of drivers/intel/wifi chip driver for Intel WiFi
devices. There is no need for two separate chip drivers in coreboot to
handle Intel and non-Intel WiFi devices since the differences can be
handled at runtime using the PCI vendor ID. This also allows mainboard
to easily multi-source WiFi chips and still use the same firmware
image without having to distinguish between the chip drivers.
BUG=b:169802515
BRANCH=zork
Change-Id: Ieac603a970cb2c9bf835021d1fb0fd07fd535280
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Refactor DPTF section of code under the baseboard devicetree
and overridetree. This makes override mechanism more simpler,
because not all the DPTF fields need to be overridden.
BUG=None
BRANCH=None
TEST=Built and tested on dedede system
Change-Id: I8e7cfe60c010ed4c07f9089325b289519e861f84
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Allow MRC training in SaGv low, mid and high frequencies.
TEST=Verify memory trains at low, mid and high SaGv point
through FSP debug logs enabled.
Change-Id: I0f60aad031ce9dfe23e54426753311c35db46c05
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45196
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If Cr50 is running old firmware version and hence does not ensure long
interrupt pulses, override the GPIO PM configuration.
BUG=None
TEST=Build and boot waddledee to OS. Ensure that any chip override
happens before FSP silicon parameter initialization. Ensure that the
suspend/resume sequence works fine. Ensure that the reboot sequence
works fine for 50 iterations.
Change-Id: I455c51d4a63b1b5edadbf00c786ce61b0ba1ff00
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
BUG=b:167472333
TEST=Build and boot dedede and observe the slope and offset values
getting updated in the fsp debug log
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I3ea32218040263f0abef9b9dd4c52efb16289fd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45825
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4151d1a6ce94763432f307fbc8bc4afe229856ea
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Enable processor thermal control using PCI dev path function instead of
Device4Enable parameter in devicetree. This change removes the dependency
on Device4Enable in devicetree. We can enable and disable this thermal
control using on and off support with PCI device entry in devicetree.
BRANCH=None
BUG=None
TEST=Built and tested on dedede board
Change-Id: I0463236996ad001af506c9966840b27fe44d60d2
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change updates devicetree to enable SSDT generation for world
facing camera and user facing camera of Waddledoo. Also reverts DSDT
changes related to both the camera.
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Change-Id: Ib7e875d297c04f35d4e980ff33d9a3767d2910ac
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Enable FW_CONFIG and add tablet mode field in devicetree
BUG=b:165613510
TEST=emerge-dedede coreboot
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I55e4c0d0b4aa2337c01773006d0b485fdcd91654
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Setting USBx_PORT_EMPTY is not a requirement anymore, since unset
devicetree settings default to 0 and the OC pin now only gets set when
the USB port is enabled (see CB:45112).
Thus, drop the setting from all devicetrees.
Change-Id: I899349c49fa7de1c1acdca24994ebe65c01d80c6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Configure TRACKPAD_INT_ODL pad reset config to DEEP and
map PMC_GPE_DW to PMC_GPP values.
TEST=System should wake from S3 via trackpad
Change-Id: I58ce3720e0fdeefb2c9440bb3006897ef80211ea
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This patch updates the SLP_Sx assertion width and power cycle duration
for the dedede platforms.
Power cycle duration:
With default value,
S0->S5 -> [ ~4.2 seconds delay ] -> S5->S0
With value set to 1,
S0->S5 -> [ ~1.2 seconds delay ] -> S5->S0
BUG=b:159104150
TEST=Verified that the power cycle duration is ~1.2s with global
reset on waddledoo.
Change-Id: I7079cbd564288b5d5b69e07661434439365063d3
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Observed thermal shutdown initiated by DPTF due to CPU temperature
reaching critical temperature trip value. During stress testing with
heavy workload like WebGL Aquarium, sometime CPU temperature spikes
till 99 degree Celsius and DPTF initiates system shutdown. This
updates CPU critical temperature trip value to 105 degree Celsius
to avoid system shutdown.
BUG=b:161993459
BRANCH=None
TEST=Built and tested on dedede system
Change-Id: If15a873a997aa80f20940f27bbafd4498908c091
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44054
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
MRC automatically detects the DDR type and sets Rcomp resistor
and target values for JSL and does not require explicit programming.
Change-Id: Ia130765e2cb91d6a39ad00ebbab20e7e87fa42d1
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
HDMI DDC GPIOs were configured as NC till now in waddledoo.
This may cause HDMI i2c transfer to break and EDID read will
fail due to wrong configuration
Configuring these GPIOs as NF in coreboot to fix the issue.
BUG=b:160324327
BRANCH=None
TEST=HDMI works on DDI2 onn Type-C port
Change-Id: If02f062132d7c3b01b07ea9401e81f451df35c3c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43294
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7378aa7d6156ece3ab3959707a69f45886f86d21
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43593
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patches enables the SkipCpuReplacementCheck config for
the dedede baseboard to avoid the forced MRC training for all
its variants with the soldered down SOC.
BUG=b:160201335
TEST=Build and verify CSE Lite SKU on Waddledoo.
Cq-Depend: chrome-internal:3142530
Change-Id: I611e66f74a3b9b090ab5e0d836231643d3f919dc
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
1. Update Link frequency to 180 Mhz
2. Set data-lanes to 1 and
3. Update the clock-lane used by sensor
BUG=b:155285666
BRANCH=None
TEST=Build and able to capture image using user facing camera.
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Change-Id: I164cb6af1003de561be8ce640e7653b7bcb3a22f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Since there is now a mechanism to generate DPTF ACPI tables and methods
at runtime, dedede should switch to using that instead of raw ASL files.
This patch converts the existing .asl files into devicetree entries.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6bb6e6e15f50a1e510080e16bbca09dfc5f16b1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43422
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For variants with slightly different GPIO configuration, add support to
pass an override GPIO configuration table.
BUG=None
TEST=Build and boot the waddledee mainboard.
Change-Id: I2f1c6dc2ea5499bff96a471c4461339ef01ee19a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Set tcc_offset value to 10 in devicetree for Thermal Control
Circuit (TCC) activation feature.
BUG=None
BRANCH=None
TEST=Built for dedede platform and verified the MSR value
Change-Id: I53d1bd413c64643cf8bdaef266bde25a2f3a97ee
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42906
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DPTF functionality on jasperlake based dedede platform
BRANCH=None
BUG=None
TEST=Built for dedede system
Change-Id: I17b6e4e96abee6181b0d1f94c356a32aa82c19b9
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41668
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In waddledee and waddledoo, discrete & integrated BT signals are routed to
different USB ports. In all the other variant boards, discrete &
integrated BT signals are routed to the same USB port (port 8 - index 7).
Re-configure the USB devices accordingly.
Also device configuration in override tree are applied only if there is a
matching device in base devicetree. So configure all the USB devices in
base devicetree and turn them off.
BUG=b:154064148
TEST=Ensure that the SSDT contains the ACPI objects for enabled USB
devices.
Change-Id: I1b8bf7f4db1d2661f310bf4874428a6d1de222c6
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42554
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add DW9768 VCM device and add its entry in the OV8856's _DSD
to allow the V4L2 driver to use the VCM functionality.
Also add ACPI entries for AT24 NVM device, this will enumerated
as a generic NVM device and not part of the V4L2 framework.
BUG=b:155285666
BRANCH=None
TEST=Build and able to see DW9768 and AT24 getting listed I2C3 lanes
and able to capture image using world facing camera.
Change-Id: I19e4a4107c5bc9d96f718d654df50e2705b98c03
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I4cadfe69e36f959b54e374800c32629a7481ea94
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The max98357a_platform_driver will turn on/off the speaker enable gpio
based on use, so configure it low to save power.
BUG=None
TEST=Built dedede and tested speaker playback working.
We are seeing a power saving of ~10mW.
Change-Id: I070679457b06cb82633c1197b893a5d89c8b2cf0
Signed-off-by: Usha P <usha.p@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
|
|
All variants are overriding soc_common_config, so source it from
overridetree and remove entry from baseboard devicetree.
Only keeping chipset lockdown config in baseboard which will be
common across all the variants.
BUG=None
BRANCH=None
TEST=Checked code compilation and lockdown config is applied to all variants
Change-Id: I23714b721a6bb0bac785f046586790a98dc5b646
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
This change allows treating the PMC as a 'hidden' PCI device on Jasper
Lake, so that the MMIO & I/O resources can be exposed as belonging to
this device, instead of the system agent and LPC/eSPI.
Change-Id: Ie07987c68388d03359c43f64a849dc6e3f94676e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
1. Configure SD card GPIOs.
2. Set SD card power polarity and card detect configs.
SD card CMD. DATA and CLK GPIOs are set for native pad termination
as per recommendation in EDS vol1 section 10.4.10
BUG=b:150872580
TEST=Verify SD card enumeration and read/write transactions.
Change-Id: I90c8ceb85ada23718ff7b6fd7013317c818dd532
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
TEST=Build and boot waddledoo board
Change-Id: Ic10af9a0d50946a98a5c4a77b492d242cef171ca
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41535
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable heci1 device from devicetree for PCI enumeration. This is
required for ME status dump using HFSTSx resgisters in PCI config
space. Heci1 device is later disabled through heci disable flow.
TEST=Build, boot waddledoo. ME status dump is seen in console logs.
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: Icb77db3f0666c2d14ebef2c3214564346d1fd3c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable Intel Speed Shift Technology (ISST) by default. Disable ISST in
waddledee and waddledoo variants on early phases.
BUG=b:151281860
TEST=Build and boot the mainboard. Ensure that cpufreq driver to
configure P-states is enabled in kernel on boards where board version is
provisioned.
Change-Id: Id65d7981501c2f282e564bfc140f8d499d5713e8
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Change-Id: I8a207e30a73d10fe67c0474ff11324ae99e2cec6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41360
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=None
TEST=Build and boot the mainboard.
Change-Id: I1aae4adf1c13fd4ff58aa38a877f34e142f320f1
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41037
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add GPIO_PCH_WP (GPP_C11) to associate GPP_PCH_WP with community
zero.
TEST=Build coreboot, flash, boot to
and log into kernel, execute "wp enable" in console,
execute "crossystem" at kernel prompt and verify that "wpsw_cur"
shows as being "1", Execute "wp disable" in console, execute
"crossystem" at kernel prompt and verify "wpsw_cur" is 0.
Change-Id: Ie4ae1365a7611b8be3e795798c171e3f7ea9e417
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40744
Reviewed-by: Usha P <usha.p@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The stuffed resistor straps are weaker compared to the internal pull-up.
This can cause the GPIO to read '1' always. Remove the internal pull-up.
Also read the GPIO only on the boards where the board version is
populated.
BUG=b:154301008
TEST=Build and boot the mainboard.
Change-Id: Ib640211b9f50dfb0174a570eda1625bacbebb855
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=None
BRANCH=None
TEST=Build and Boot waddledoo board and able to capture image
using world facing camera.
Change-Id: I51dcf96a82535fc1e0b9247fd52af919885575e5
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
1. Add support as per the schematics
2. Add 2 Ports and 2 Endpoints
3. Add support for OTVI8856 and OTVI5676
4. Add ON and OFF logic as Power Rails are same for both sensor
BUG=None
BRANCH=None
TEST=Build and Boot waddledoo board and able to capture image
using world facing camera.
Change-Id: Ic8687bce4896d9fc17b2190b8d11618af3515cc1
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Disable dynamic clock gating for the community cr50's IRQ lives on.
That IRQ is pulsed very quickly, and with clock gating enabled pulses
tend to be missed. This is expecially true on the default 0.0.22
firmware that cr50 comes with out of the factory.
BUG=b:154178408 b:154293730
BRANCH=None
TEST=build waddledoo successful and Linux has no TPM IRQ timeout error.
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I2b1b3ee59ebf6adce0653e7550b457e02d3c87df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Configure DRAM population strap GPIO according to the schematics.
Configure an internal pull-up to support the boards in which the strap
is not populated. Read the strap and pass that information to FSP for
memory initialization.
BUG=b:152275658, b:154301008
TEST=Build and boot the mainboard. Ensure that the strap information is
read as expected and passed to FSP.
Change-Id: I69583f35ffc219bae9ce06bd4ba9898ed0d4d21d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39812
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SiS9813 USI touchscreen support.
BUG=b:152936541
TEST="emerge-dedede coreboot chromeos-bootimage", build successful.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Id04c46c763fdf68418bf2e97be4c8bb6bb73c749
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40250
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to the EDS, EC_AP_PWR_BTN_ODL has a default internal pull-up
of 20K. Retain it during the GPIO pad configuration.
BUG=b:150985246
TEST=Boot the mainboard.
Change-Id: I042ba70f78fca1a5b9eda30029df97b3f8e65656
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39852
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Switch to using Jasper Lake SoC code from soc/intel/jasperlake and stop
referring from soc/intel/tigerlake.
Addtionally mainboard changes are done to support build.
BUG=b:150217037
TEST=Build and boot waddledoo. Build jasperlake_rvp and volteer board.
Change-Id: I39f117bd66cb610a305bcdb8ea65332fd0ff4814
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The concerned GPIO is configured as an open drain at the Embedded
Controller side without an external pull-up. This causes leakage in the
PP3300_A rail. So configure the GPIO to have a weak internal pull-up at
the SoC side.
BUG=b:151680590
TEST=Build the mainboard. Ensure that there are no leakages in the
PP3300_A rail.
Change-Id: I5553cf40adb92edc0fecab5c875ec8d72063ba7b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
1. Configure Audio GPIOs.
2. Set i2c4 configuration.
3. Update PCH HDA configuration
TEST=Verify codecs gets listed with aplay -l command.
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Change-Id: Ic0516c7a8fee79ce17343a7f42895d6ef534fec9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The integrated BT is routed via USB2 port 8, add USB configuration
to support integrated BT enumeration.
Change-Id: I46d8c92ba57cd72a91ee15ef4d11f07824c29e9a
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I09cc279b1f75952bb397de2c3f2b299255163685
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Turn on CNVi device. Turn on PCIe Root port that hosts WLAN device.
Configure PCIe Clk Source and Clk Request mapping. Configure GPIOs used
for WLAN - both CNVi and M.2.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I9bb8e57cdb688bc544929c94af380b9ef1d936a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Disable the BT module in bootblock and enable it in ramstage. This
allows for loading the BT firmware during reboot.
TEST=Build and boot the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0406a68ffcab2675a1aedb212cb7c8508a5b61fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39446
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Configure trackpad interrupt GPIO.
2. Set i2c0 configuration.
3. Add trackpad ACPI support.
TEST= Verify trackpad working. Verify I2C SCL frequency below 400Khz
on trackpad operation.
Change-Id: I52c578aef591f5be90fb709bab4c8342ea9729e6
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable USB ACPI driver. Add ACPI configuration for all the USB ports.
Since one of the USB ports is used for Bluetooth configure the
reset_gpio used by that port.
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I3e7b8f00102c96dcc295601359d3ecfbcd1bea00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Add configuration for all the PCIe Root ports and Clock Source.
Configure the Root Ports as disabled and clock sources as not used.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0a1ad7e056907e454a93f51c84e1d99f08b7bdef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39166
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This enables display for use by payload.
TEST=Build and boot the mainboard. Ensure that the screens displayed by
payload are visible.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5fcd70623b15ae39954242605e75b2c5ce02ff14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:150869661
TEST=Build and boot the mainboard. Trigger apreset from EC console.
Trigger reboot from AP console.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0d6dd0b4264c11f7ee0ef436cc819b0bb92974f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39325
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Leave all the GPIOs in not connected state so that they can be
configured depending on the use-case. This is done to park the GPIOs in
a known safe state. This will also help to ensure that the required
GPIOs are configured when the concerned use-cases are enabled.
Below GPIOs are configured in Native Function 1 and are required for
boot-up.
* VCCIN_AUX_VID0
* VCCIN_AUX_VID1
* AP_SLP_S0_L
* PLT_RST_L
* CPU_C10_GATE_L
* GPDs
BUG=None
TEST=Build and boot the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5293536f66a6b08c9c2d2a6281684755a0c0b1b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39114
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update memory parameters based on memory type supported by dedede
1. Update dq/dqs mappings
2. Update spd data for Micron Memory
3. Add SPD data binary files for supported memory types
4. Update other FSPM UPDs as part of memory initialization
BUG=none
BRANCH=none
TEST=Build dedede, flash and boot to kernel.
Change-Id: I7248861efd1ecd5a0df0e17d39a44c168cab200e
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39136
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure below ESPI IO decode ranges:
1. 0x200-020F: EC host command range.
2. 0x800-0x8FF: EC host command args and params.
3. 0x900-0x9ff: EC memory map range.
Change-Id: I1e450d6e45242180de715746b9852634de2669c6
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39121
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
1. Enable Internal Gfx device.
2. Configure DDI0 for EDP.
3. Configure HPD and DDC suppport for DDI1/DDI2.
4. Configure HPD GPIOs.
TEST=Verify display on EDP panel in OS
Change-Id: Ia53428af549ba01ab539f9474a6e5e79b72dff5c
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39132
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
WWAN wake event is routed to GPP_D0 GPIO and Pen Detect wake event is
routed to GPP_C12 GPIO. Update the GPE configuration accordingly.
BUG=None
TEST=Build the mainboard.
Change-Id: Id36d2c8265a0b7ea241565f6bb723df6b37446fa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: Ie47265527b2b81748f4f3ad744d35cb81af17b80
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Turn on EMMC device and enable the HS400 mode. Configure the GPIOs
associated with EMMC.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ic27c68f4622eec5b2930dc38186b82d895d3f67c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
Add USB port configuration in devicetree. Configure USB Over-Current (OC)
GPIOs.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I19f7563013c7d702d52b7f34a207a34abe308621
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
Enable I2C ports that are used. Add GPIO configuration for the I2C
ports. Enable config items that are required for I2C HID & Generic devices.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I12e974530fb5f61fae5d12cadbb3f928e617d73a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Enable UART Port 2 as console UART and configure the concerned GPIOs.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I30a64a3c96226ce3244d55919b6d65fbf0a096e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38776
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turn on the H1 device in the devicetree. Configure the concerned GPIOs
and enable the required config items.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I37972635454cd0d35608623e7be4110012ace658
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38772
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add initial configuration for GSPI, I2C and UART ports and leave them in
disabled state.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I1cd7659337e6330a8ece34df247e399a085d21d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I12a63e5776619e5a7684cf1edad78b0fd6fac12c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38739
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the GPIO groups to be routed to the GPE0 block.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ife4d0179bd9fe1785e971686478f7c76de805e87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add compute and PCH Global device IDs with the concerned devices turned
off.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I6f226abd52d4a27535de6711e93355b5f84a1941
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add helper functions to get board's sku_id and fw_config. Enable
EC_GOOGLE_CHROMEEC_BOARDID to get board_id. Add board's SKU ID and
OEM name into SMBIOS table.
BUG=b:144768001
TEST=Build Test.
Change-Id: Id1729e245accf5acc29307a22721362fb1ce0878
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38551
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Perform EC initialization in bootblock and ramstages. Add associated ACPI
configuration.
BUG=b:144768001
TEST=Build Test.
Change-Id: Ib31ae190818c8870bdd46ea6c3d9ca70dc0485cc
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable building for Chrome OS and add associated ACPI configuration.
BUG=b:144768001
TEST=Build Test
Change-Id: Ibb94849a903e4d4364d817de8988a430cd717e4c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add stub implementation of smihandler.
BUG=b:144768001
TEST=Build test.
Change-Id: I7ab25888812bfb4578915e342b14355ccd15f5cc
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add stubbed out GPIO configuration and perform GPIO initialization
during bootblock and ramstage.
BUG=b:144768001
TEST=Build Test
Change-Id: I1397b6a433e5046650f64f7eb9a84c51eb0c7441
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38278
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add mainboard stubs for Dedede. More functionalities will be added later.
BUG=b:144768001
TEST=Build test.
Change-Id: I7e6cb8adaee7b6bb95e9a96f96466646a78bd0fc
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38277
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|