| Age | Commit message (Collapse) | Author |
|---|
|
These typos were found through manual review and grep.
Change-Id: Ia5a9acae4fbe2627017743106d9326a14c99a225
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/22525
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change 1760cd3e (soc/intel/skylake: Use common/block/gpio) updated all
skylake boards to use common gpio driver. Common gpio code
defines PAD_CFG_GPI without GPIO_DRIVER ownership. However, for
skylake PAD_CFG_GPI set GPIO_DRIVER ownership by default. This
resulted in Linux kernel failing to configure all GPIO IRQs since the
ownership was not set correctly. (Observed error in dmesg: "genirq:
Setting trigger mode 3 for irq 201
failed (intel_gpio_irq_type+0x0/0x110)")
This change fixes the above issue by replacing all uses of PAD_CFG_GPI
in skylake mainboards to PAD_CFG_GPI_GPIO_DRIVER.
BUG=b:67507004
TEST=Verified on soraka that the genirq error is no longer observed in
dmesg. Also, cat /proc/interrupts has the interrupts configured
correctly.
Change-Id: I7dab302f372e56864432100a56462b92d43060ee
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add the voltage tolerance GPIO attribute for configuring I2C/I2S buses
that are at 1.8V. This is currently done by passing in a value to FSP
but it is needed earlier than FSP if the I2C bus is used in verstage.
This does not remove the need for the FSP input parameter, that is
still required so FSP doesn't disable what has been set in coreboot.
The mainboards that are affected are updated in this commit.
This was tested by exercising I2C transactions to the 1.8V codec while
in verstage on the google/chell mainboard.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I93d22c2e3bc0617c87f03c37a8746e22a112cc9c
Reviewed-on: https://review.coreboot.org/15103
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
With gpio PADRSTCFG set to DEEP & GPIROUTIOXAPIC=1 & PADRSTCFG, causes
IRQ storm after S3 resume. GPIOs that fire IRQs via IOAPIC need to get
their logic reset over pltrst and hence configuring PADRSTCFG to
PLTRST to prevent IRQ strom after S3 resume.
BRANCH=glados
BUG=chrome-os-partner:50536
TEST=Build for kunimitsu and Boot on FAB4, no irq storm observed
after S3 resume.
Change-Id: I7f1ae90aed03778e7d6cb2d79de0efe9a6d9e20d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: aff91da4feaf8f7e42cfeee756cf468288cbfd68
Original-Change-Id: I7cac60fb0144e090b8decb05d948b2d8d2f8deac
Original-Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/329453
Original-Commit-Ready: Naresh Solanki <naresh.solanki@intel.com>
Original-Tested-by: Naresh Solanki <naresh.solanki@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/331174
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/13992
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add new GPIOs for touchscreen enable and reset pins and define
the one missing unconnected pin for GPP_E10.
BUG=chrome-os-partner:50518
BRANCH=glados
TEST=build and boot on chell DVT1
Change-Id: I565a742ff266ee65a5d33f052606fe77c24b6ac8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: 32a890af8c32aa30adac256d2c4ceaeefa30bd0d
Original-Change-Id: I16546d38cc4e926e169f61ae1843106d1e14936b
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/329297
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13841
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Instead of relying on power-on-reset values provide configuration
for all pads. PAD_CFG_NC() was used for all pads which had no nets
routed on the board. PAD_CFG_GPO(0) was used for pads which had nets
routed on the board in order to terminate them.
BUG=chrome-os-partner:50301
BRANCH=glados
TEST=Built and booted chell. Suspended and resumed on EVT.
Change-Id: I7960442d5c06f58a1b671cdefac71ef0bc3b0cd5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: 6a167cd0a747402bfc3cc9b6fbaaceceda766ee9
Original-Change-Id: I519011b049235dc2a960939c0bed274252dbffa8
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/327835
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/13831
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
- Add pullup on LPC address lines for leakage
- Configure PCH_WP early so it gets set properly in VBNV
- Disable SD card reader in favor of USB
BUG=chrome-os-partner:47346
BRANCH=none
TEST=build and boot on chell EVT
Change-Id: Ibac79c6cbef0515b1e8a513cfde5fee184e4c70a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ebd0c16a6009b74d3c6c36878c502fda9bb3020d
Original-Change-Id: If2bc4eb546a1aab50d3688b6e92f8c38214c9cca
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/317241
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12979
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
- Disable kepler device, it is removed and was not used on proto anyway.
- Enable GPP_D22 as GPO to control I2S2 buffer for bit-bang PDM.
- Disable HS400, this is breaking some devices on proto boards and
is being disabled to reduce risk for EVT build.
- Change Type-C USB2 port drive strength.
BUG=chrome-os-partner:47346
BRANCH=none
TEST=build and boot on chell proto
Change-Id: Icf31f08302c89b2e66735f7036df914c0a0b9e8c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d00abc12efa69a99e6b0272228f52fb29e6b9180
Original-Change-Id: I63bda0b06c7523df9af9aed9b82280133b01d010
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/313825
Original-Commit-Ready: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12598
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The GPIO for USBA_1_ILIM_SEL_L should be low to enable 2A charging
from the Type-A port.
BUG=chrome-os-partner:47172
BRANCH=none
TEST=emerge-glados coreboot
Change-Id: I1bbcdd467684e7c1372c8ca862d498fb6cbb966c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c8a8fbed6d0fd7aea0a41db2bde104fe7a05cabe
Original-Change-Id: I3b18cbb204cfa19e50f34ea9533018e286342513
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/312451
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12447
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
For the rails controllable by the host processor through
gpios turn them off in the sleep paths. The result is that
S3 and S5 will turn off those rails.
BUG=chrome-os-partner:47228
BRANCH=None
TEST=Built for chell.
Change-Id: I5843f13be43a6ec143600585a5a0c47563e533dd
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ddd5860dc0cfee68ec2f77f4931665740bede08c
Original-Change-Id: Ife0e2fb11373dd129e20b914b45cd5b56c3493f7
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/312321
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/12446
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This is based on glados with minor changes:
- updated GPIOs based on schematic
- add _PRW for trackpad wake now that it is on a new GPIO
- add SPD for new memory config
- disable ALS
BUG=chrome-os-partner:46289
BRANCH=none
TEST=emerge-chell coreboot
Change-Id: Id5746bf2b5b26000fcc3f029b901bfe29b788dac
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9c5ebe98cf599ba80aac5e9ef238b7996789a819
Original-Change-Id: I75efda64a50b0e6e4a5c9008ce05d76c1e605b0c
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/304927
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12151
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Only change is renaming all occurrences of glados to chell, keeping
capitalization.
Change-Id: I8b1a3efd03d415f27c8872827f8687babbc539f7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/12150
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
