| Age | Commit message (Collapse) | Author |
|---|
|
ALC257 does not supoort built-in digtal buzzer, So use external pwm
to PCBEEP for beep sound.
BUG=b:346956771
BRANCH=None
TEST=emerge-brox coreboot sys-boot/chromeos-bootimage
firmware-shell: devbeep -> can output beep normally.
Change-Id: If924f9f27f229420e78015f418a97b2d5daf62e5
Signed-off-by: Jing Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The Fn key on Lotso emits a scancode of 94 (0x5e).
BUG=b:322721490
TEST=Flash Lotso, boot to Linux kernel, and verify that KEY_FN is
generated when pressed using `evtest`.
Change-Id: I999627f0ea9db1d79376150a04920ac877a48447
Signed-off-by: Wen Zhang <zhangwen6@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83204
Reviewed-by: Dengwu Yu <yudengwu@huaqin.corp-partner.google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
On board version 1 and later, touchscreen is not stuffed. Hence
configure the relevant GPIOs as not connected, disable the concerned I2C
bus in the devicetree as well as SoC chip config for board version 1.
BUG=b:347333500
TEST=Build Brox BIOS image and boot to OS. Ensure that there are no
peripherals detected in I2C 1 bus through i2cdetect tool. Ensure that no
touchscreen devices are exported through ACPI SSDT table. Ensure that
other I2C peripherals - eg. Trackpad and Ti50 are functional. Ensure
that the device is able to suspend and resume for 25 cycles.
Change-Id: Ia0578b90b0e8158ae28bcc51add637844ba6acf6
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83199
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kernel need the default brightness steps. Otherwise following error
messages are observed in the kernel:
[Firmware Bug]: ACPI(GFX0) defines _DOD but not _DOS
ACPI BIOS Error (bug): Could not resolve symbol [^^XBCL], AE_NOT_FOUND
ACPI Error: Aborting method \_SB.PCI0.GFX0.LCD0._BCL due to previous
error (AE_NOT_FOUND)
BUG=b:346807006
TEST=Build Brox BIOS image and boot to OS. Ensure that the concerned
error messages are resolved. Ensure that the backlight controls are
functional.
Change-Id: Icd569b0efef31908edb1b7dc384e60a16fc5bd0c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83152
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Update board type to BOARD_TYPE_ULT_ULX
BUG=b:348147663
BRANCH=none
TEST=Built and compare the results of
command 'dmidecode --type 17 | grep Speed'
[Before]
Speed: 8400 MT/s
Configured Memory Speed: 6400 MT/s
[After]
Speed: 8400 MT/s
Configured Memory Speed: 5200 MT/s
Change-Id: I049d7c19424f41e83480f4b80bafd6ef8b9e30f6
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
|
|
Set PsysPL2 and PsysPL3 in addition to making adjustments
to PL2 and PL4 in order to prevent brownouts when we don't
have a battery or have an empty battery at boot time.
BUG=b:335046538,b:329722827
BRANCH=None
TEST=flash
Able to successfully boot on a SKU1 with 45W, 60W+ adapters
and SKU2 with a 60W or higher type C adapter.
30W is still being worked on.
Change-Id: Ie36f16b2c938dce29cd2130a86fc8c08f5ba0902
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Lotso's WIFI_BT is same design as brox, copy from brox.
BUG=b:339612353
TEST=emerge-brox coreboot chromeos-bootimage and boot on
Change-Id: I030e306dc5d9d3fcb6314bc491dbf5c9ae60bcb7
Signed-off-by: Jing Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83126
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
|
|
Based on schematics NB7228A_LOTSO_INTEL_MB_PROTO_20240521A_BOM.pdf update devicetree settings.
BUG=b:333494257
TEST=emerge-brox coreboot chromeos-bootimage and boot on
Change-Id: Ic9a7a9062f5c6e45c5bd9617f3b2a0634b8dc1db
Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83051
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update verb table provided by Realtek on 20240614.
BUG=b:344471736
TEST=emerge-brox sys-boot/coreboot sys-boot/chromeos-bootimage
Device list:
cat /sys/bus/hdaudio/devices/ehdaudio0D0/chip_name
ALC257
cat /sys/bus/hdaudio/devices/ehdaudio0D0/vendor_name
Realtek
Headphone detection:
Event: time 1718633617.056092, type 5 (EV_SW), code 2 (SW_HEADPHONE_INSERT), value 1
Event: time 1718633621.471708, type 5 (EV_SW), code 2 (SW_HEADPHONE_INSERT), value 0
Event: time 1718633623.898046, type 5 (EV_SW), code 2 (SW_HEADPHONE_INSERT), value 1
Event: time 1718633625.743663, type 1 (EV_KEY), code 115
(KEY_VOLUMEUP), value 1
Event: time 1718633625.743678, type 1 (EV_KEY), code 115
(KEY_VOLUMEUP), value 0
Change-Id: Idde8963de9302849f87b7c262f17d9c9d99b46dc
Signed-off-by: Jing Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83109
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 0e0bc618e3ed1888ac140010057dc7485443c3c2.
Reason for revert: Merged out of order, breaks tree
Change-Id: I22bd85a2008db471177257a8b779c06898b1010c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83105
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Lotso's WIFI_BT is same design as brox, copy from brox.
BUG=b:339612353
TEST=emerge-brox coreboot chromeos-bootimage and boot on
Change-Id: I3946297db7f10a31570f773bdc5665f9f472c9fe
Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83053
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Generate RAM IDs for
K3KL6L60GM-MGCT
H9JCNNNBK3MLYR-N6E
K3KL8L80DM-MGCU
MT62F1G32D2DS-023 WT:C
H58G56BK8BX068
BUG=b:333494257
BRANCH=None
TEST=Run part_id_gen tool without any errors
Change-Id: I7a240a263816193b9f3d418385c1673e9d3f89db
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
|
|
Based on lotso EVT schematics update gpio settings.
GSPI0_CS0_L -> NF7
GSPI0_MISO -> NF7
GSPI0_MISO -> NF7
GPP_F18 -> EDGE_SINGLE
BUG=b:333494257
TEST=emerge-brox coreboot chromeos-bootimage and boot on
Change-Id: I12d84538566c4d51fe346eb5609e55d91ddafbea
Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
|
|
Current existing temperature thresholds of TSR1 sensor are set at 60C
to start fan. Due to this CPU gets hot and temperature goes over 80C.
In this situation, fan does not even start to lower down CPU temperature.
With updated new settings based on tuning from thermal team, start fan
early at 40C for TSR0 and TSR1 so the CPU temperature stays below 80C.
BUG=b:339493551
TEST=Built and tested on google/brox board
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Change-Id: I4765c13c10e436733d8c9d017085968daa561ccc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82784
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Based on lotso EVT schematics add dq map settings.
BUG=b:333494257
TEST=emerge-brox coreboot chromeos-bootimage and boot on
Change-Id: I4f03e8a90522cbf2fe06f4160414202dcc4a2199
Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82600
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Dengwu Yu <yudengwu@huaqin.corp-partner.google.com>
|
|
Based on lotso EVT schematics update gpio settings.
BUG=b:333494257
TEST=emerge-brox coreboot chromeos-bootimage and boot on
Change-Id: I13485cc7ccd8b15352f5e21ad9336aa2b3d35749
Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82573
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Select MAINBOARD_USE_EARLY_LIBGFXINIT for brox to enable SOL image.
This patch enables Sign of Life image during MRC training.
BUG=b:335369811
TEST=Able to boot to ChromeOS with SOL image.
CPU log:
[SPEW ] bootmode is set to: 0 (boot with full config)
[0.384818] DP PHY mode status not complete
[0.388911] DP PHY mode status not complete
[0.393197] DP PHY mode status not complete
[0.397484] DP PHY mode status not complete
[0.401771] DP PHY mode status not complete
[0.406057] DP PHY mode status not complete
[0.410345] DP PHY mode status not complete
[0.414632] DP PHY mode status not complete
[0.418916] DP PHY mode status not complete
[0.423203] DP PHY mode status not complete
[0.427491] DP PHY mode status not complete
[0.431777] DP PHY mode status not complete
[INFO ] Informing user on-display of memory training.
[DEBUG] FMAP: area COREBOOT found @ 1877000 (7901184 bytes)
[WARN ] CBFS: 'preram_locales' not found.
[ERROR] ux_locales_get_text: preram_locales not found.
[DEBUG] FMAP: area RW_ELOG found @ f20000 (16384 bytes)
[INFO ] ELOG: NV offset 0xf20000 size 0x4000
elogtool list:
0 | 2024-05-10 02:26:07-0700 | Log area cleared | 4088
1 | 2024-05-10 02:26:07-0700 | Early Sign of Life | MRC Early SOL Screen Shown
2 | 2024-05-10 02:26:51-0700 | Memory Cache Update | Normal | Success
3 | 2024-05-10 02:27:09-0700 | System boot | 4
4 | 2024-05-10 02:27:09-0700 | Firmware Splash Screen | Enabled
5 | 2024-05-10 02:27:11-0700 | System Reset
6 | 2024-05-10 02:27:11-0700 | Firmware vboot info | boot_mode=Developer | fw_tried=A | fw_try_count=0 | fw_prev_tried=A | fw_prev_result=Unknown
7 | 2024-05-10 02:27:18-0700 | ACPI Enter | S5
8 | 2024-05-10 02:27:36-0700 | System boot | 5
9 | 2024-05-10 02:27:36-0700 | Firmware Splash Screen | Enabled
10 | 2024-05-10 02:27:37-0700 | System Reset
11 | 2024-05-10 02:27:37-0700 | Firmware vboot info | boot_mode=Developer | fw_tried=A | fw_try_count=0 | fw_prev_tried=A | fw_prev_result=Unknown
Change-Id: I1d4795825960bc58f8f7ef494b01aa975f3bc346
Signed-off-by: Sowmya Aralguppe <sowmya.aralguppe@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
|
|
The Type-C kernel driver no longer programs the AP mux, as of
https://review.coreboot.org/c/coreboot/+/82077. So remove device
references to the TCSS Mux control device from the Type-C port driver.
This eliminates the following kernel error which was observed as a
result of the kernel trying to program muxes it no longer has control
over:
[ 4.618600] cros-ec-typec GOOG0014:00: Failed to get mux info for port: 0, err = -95
[ 4.618608] cros-ec-typec GOOG0014:00: Configure muxes failed, err = -95
BUG=b:341331428
TEST=Run system reboot; configure mux kernel errors no longer seen.
Change-Id: I93e498b12b109c0e649a23a4a49868976a9ee06b
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82599
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit f867c9c5473156617691d78350c362cd993bfcdd.
The new verb table breaks external mic detection on brox.
Revert and use old verb tables instead.
BUG=b:330433089
BRANCH=main
TEST=Verified headset on Brox
When connected to audiojack in power_save state of legacy hda driver,
headset is detected and audio is resumed.
Change-Id: I0d8c092de6166b2c62f5ecc3deaf4960128e6106
Signed-off-by: Terry Cheong <htcheong@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82273
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On GreenbayPOC, HDA Codec used is ALC236, different with Brox (ALC256)
Update to Realtek provided verb table for ALC236 audio codec.
BUG=b:336967284
TEST=Verified headset and audio workable on DUT with "rec" and
"aplay" command.
Change-Id: I9fbe57a0acab20387754f6b6cb5705e34c1c149b
Signed-off-by: Wu Garen <wu.garen@inventec.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82413
Reviewed-by: Ivan Chen <yulunchen@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Copy the data.vbt from brox to greenbayupoc
BUG=b:326413034
TEST=emerge-brox coreboot chromeos-bootimage, flash and boot on DUT
Change-Id: I1e8101519ab2ecbb4654c20485fbe83c90656e4d
Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82108
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on latest schematics GREENBAY_0412.SCH update the gpio and
devicetree settings.
BUG=b:326413034
TEST=emerge-brox coreboot chromeos-bootimage, flash and boot on DUT
Cq-Depend:chrome-internal:7218819
Change-Id: I59f25b8abb7dd8a2dff7ff567b231bddc9db8455
Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Disable c1 state auto-demotion support for brox
BUG=None
BRANCH=None
TEST=Boot brox and verify in fsp debug logs
Change-Id: I18d40cd721d46fce4702cf1a943583cd41c03cf4
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82104
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure SODIMM settings for greenbayupoc. The SODIMM settings are
copied from mainboard/google/brya/variants/baseboard/brask/memory.c.
BUG=b:336955026, b:332230842
TEST=emerge-brox coreboot chromeos-bootimage, flash and boot to OS
using Hynix HMAG56EXNSA051N 4G and Micron MTA8AFT1G64HZ-3G2R1 8G SODIMM.
Change-Id: I1552cadfa81c48fe561947ded078bcca2e6bc6ad
Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82085
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Currently EOP message is sent to CSE late in the boot flow. Instead send
it asynchronously to save ~10 ms in boot time.
BUG=b:337330958
TEST=Build Brox BIOS Image and boot to OS.
Change-Id: I229d16a5dcd072958db3f59a9c364bf7508b3047
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Update the pad reset config for WLAN Interrupt from PLTRST to DEEP
so that it can still act as a wake source during S3 suspend.
BUG=b:336398012
TEST=Build Brox BIOS image and boot to OS. Suspend to S0ix & S3 and
wakeup successfully using Wake on WLAN.
268 | 2024-05-07 13:56:44-0700 | S0ix Enter
269 | 2024-05-07 13:57:07-0700 | S0ix Exit
270 | 2024-05-07 13:57:07-0700 | Wake Source | GPE # | 3
271 | 2024-05-07 13:59:01-0700 | ACPI Enter | S3
273 | 2024-05-07 13:59:26-0700 | Wake Source | PME - WIFI | 0
274 | 2024-05-07 13:59:26-0700 | ACPI Wake | S3
275 | 2024-05-07 13:59:26-0700 | Wake Source | GPE # | 3
Change-Id: Ie0d6e6c8fefdd081e252ea99d6e3c559a5330b0e
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82234
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to Brox HW design, the PsysPmax is supposed to be 208W.
This patch changes PsysPmax setting from 21.5W to 208W.
Change-Id: I43f4b00a54dc0dfe6bd690492f9ef92698c9b903
Signed-off-by: Lawrence Chang <lawrence.chang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Brox uses PDC<->PMC direct connection for USBC mux configuration. Select
SOC_INTEL_TCSS_USE_PDC_PMC_USBC_MUX_CONFIGURATION to enable it. This
patch also adds additional dependency on ENABLE_TCSS_USB_DETECTION to be
selected only when PDC<->PMC direct connection and CHROMEOS is not used.
BUG=b:332383540
TEST=USB3 plugged during G3, is detected after system boots from G3.
Cq-Depend: chromium:5484387
Cq-Depend: chrome-internal:7106592
Change-Id: I0f62943f87d8fb6eb494c0aca3ef08c33cd05ffd
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Alderlake and Raptorlake SoCs support DDR4 and DDR5, which have a total
SPD size of 512 bytes. Set this as the default and remove the setting
from mainboard Kconfigs.
Change-Id: I8703ec25454a0cd55a3de70f73d2117285a833ae
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82115
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_D14 is floating when ISH is not being used and wasting power. Add
pulldown to prevent this from happening.
BUG=b:336654954
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
make sure OS boots up
HW team validated that power usage is 20 mW lower
Change-Id: I4e19e98fa31022ece66a47402a2a4461b430ef70
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update the pad reset config for Touchpad Interrupt from PLTRST to DEEP
so that it can still act as a wake source during S3 suspend.
BUG=b:336398012
TEST=Build Brox BIOS image and boot to OS. Suspend to S3 and wakeup
using Trackpad.
246 | 2024-04-25 16:55:18-0700 | ACPI Enter | S3
247 | 2024-04-25 16:55:34-0700 | ACPI Wake | S3
248 | 2024-04-25 16:55:34-0700 | Wake Source | GPE # | 67
249 | 2024-04-25 17:00:38-0700 | ACPI Enter | S3
250 | 2024-04-25 17:00:47-0700 | ACPI Wake | S3
251 | 2024-04-25 17:00:47-0700 | Wake Source | GPE # | 67
Also suspend to S0ix and wakeup using Trackpad.
Change-Id: If1a275e42c6c7ad743eedc9cd3320776008bfd62
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Add STORAGE_UNKNOWN, STORAGE_UFS, STORAGE_NVME for storage fw_config
field to prevent depthcharge build break.
BUG=b:333494257
TEST=emerge-brox coreboot depthcharge sys-boot/chromeos-bootimage
Change-Id: Idb62e3f37e1480979ae529692455beb533434520
Signed-off-by: tongjian <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82056
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Commit 00b40090aecf ("mb/google/brox: Move hda verb to variant dir")
introduces a variant-specific file for the HDA verb tables, which
commit 1bf0c3f1897c ("mb/google/brox: Create lotso variant") was missing
which caused the build to fail when both patches were submitted. To fix
the tree, add this file to the newly created lotso variant.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8a85115a204d9d9447a58da71eb65b1de963023d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82014
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Create the lotso variant of the brox reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:333494257
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brox -x -a
make sure the build includes GOOGLE_LOTSO
Change-Id: I5939127f9e6abe5b792c0627d9d67e739b27083b
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Others variant boards might use diff HDA Codec, so move hda verb
to brox variant dir.
BUG=b:314702466
BRANCH=None
TEST=emerge-brox sys-boot/coreboot sys-boot/chromeos-bootimage
Device list:
cat /sys/bus/hdaudio/devices/ehdaudio0D0/chip_name
ALC256
cat /sys/bus/hdaudio/devices/ehdaudio0D0/vendor_name
Realtek
Headphone detection:
evtest 8
Event: time 1713404716.656768, type 5 (EV_SW), code 2 (SW_HEADPHONE_INSERT), value 1
Event: time 1713404716.656768, -------------- SYN_REPORT ------------
Event: time 1713404722.802661, type 5 (EV_SW), code 2 (SW_HEADPHONE_INSERT), value 0
Event: time 1713404722.802661, -------------- SYN_REPORT ------------
Change-Id: Id987c248c37dc8bdc63be7a2513fa8997b5ddc33
Signed-off-by: tongjian <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81945
Reviewed-by: Poornima Tom <poornima.tom@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add STORAGE_UNKNOWN, STORAGE_UFS, STORAGE_NVME for storage fw_config
field to prevent depthcharge build break.
BUG=b:333325006
TEST=emerge-brox coreboot depthcharge with no errors
Change-Id: I0e220787d6ac73ec8fa2469ed958981d0801920e
Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivan Chen <yulunchen@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Enable SaGv support for brox
BUG=None
BRANCH=None
TEST=Boot brox with SAGv enabled and verify in fsp debug logs
Change-Id: I80c44e7df1d75732c6982b27e44ecd6060b1b3f1
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81556
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the greenbayupoc variant of the brox reference board by copying
the template files to a new directory named for the variant.
BUG=b:329530883
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brox -x -a
make sure the build includes GOOGLE_GREENBAYUPOC.
Change-Id: I90936d97b41e59c49dd92997146caf580bce1f4f
Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
The GPIO for NOTE_BOOK_MODE has changed from GPP_B17 to GPP_E9. Also
initializing it (if ISH is enabled) to be NF2 (ISH_GP4). Also took
the liberty of alphabetizing all the ISH GPIOs to they're easier to
search through.
BUG=b:316421831
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
Make sure that brox device still boots up with this change.
Change-Id: I4a091b58deb855c7a7f1489a9506db2f821503b7
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81789
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct verbtable value for pin widget 20 of Realtek ALC256 based on the
updated verbtable received from Realtek. Updated Version : 5.0.3.1. This
fixes the headset detection failure, when power_save is enabled in
legacy hda driver.
BUG=b:330433089
BRANCH=None
TEST=Verified headset on Brox
When connected to audiojack in power_save state of legacy hda driver,
headset is detected and audio is resumed.
Change-Id: I71b7d59b3ab5310a0b6cdb31fb5033f94263d151
Signed-off-by: Poornima Tom <poornima.tom@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81654
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Terry Cheong <htcheong@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Enable SMLINK1 interface for PMC-PD communication to configure Type-C
muxes.
Refer RPL EDS vol 1: 765585.
BUG=b:327622474
BRANCH=None
TEST=Boot image on SKU2 and check PMC-PD working.
Change-Id: Ia678d291e7a14aefe09026e70478fea3f68c8e10
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81207
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Deepti Deshatty <deepti.deshatty@intel.com>
|
|
ISH Firmware name needs to be configured only when full sensing
capabilities are enabled through ISH_ENABLE FW_CONFIG. Similarly DMA
property needs to be added only when UFS is enabled through STORAGE_UFS
FW_CONFIG. Hence configure the ISH device at run-time based on
FW_CONFIG.
BUG=b:319164720
TEST=Build Brox BIOS image and boot to OS.
Change-Id: I678416acd48e03ab77ae299beae6e295a688b8df
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81418
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Change-Id: If68303cd59b287c8a5c982063b2ab75fd74898d6
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
|
|
Wake signal from EC is routed to GPP_D1 and hence GPE_EC_WAKE
corresponds to GPE0_DW1_01. Fix GPE_EC_WAKE configuration.
BUG=b:329026602
TEST=Build Brox BIOS image and boot to OS. Trigger suspend and wake up
using EC generated events like AC connect/disconnect.
Change-Id: Ifb89bd0de7b7fc316792e801ed5a1d3f25ca5b1c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Keith Short <keithshort@chromium.org>
|
|
Configure I2C0/1 timing in devicetree to meet timing requirement.
(THIGH(us) minimum is 0.6us).
Before:
I2C0 : THIGH(us) 0.595us
I2C1 : THIGH(us) 0.582us
After:
I2C0 : THIGH(us) 0.673us
I2C1 : THIGH(us) 0.666us
Change-Id: I79af4fde4eb08d4eb896794756a633701bebb755
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81348
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Set FW_CONFIG bit 21 to enable ISH PCI device and define ISH main
firmware name so ISH shim loader can load firmware from file system.
ISH also need to be enabled if STORAGE_UFS is set.
BUG=b:280329972
TEST= Set bit CBI FW_CONFIG bit 21
Boot Brox board, check that ISH is enabled and loaded
lspci shows: 00:12.0 Serial controller: Intel Corporation Alder
Lake-P Integrated Sensor Hub (rev 01).
Change-Id: Iadc5108c62737d27642a6948c00b5c122541aaba
Signed-off-by: Li Feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80773
Reviewed-by: Tanu Malhotra <tanu.malhotra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Yuval Peress <peress@google.com>
|
|
Select USE_UNIFIED_AP_FIRMWARE_FOR_UFS_AND_NON_UFS in brox Kconfig.
This enables a single binary for both SKU1 and SKU2. For SKU2, upon
boot from cold reset, it will disable the UFS Controller and then
trigger a warm boot.
BUG=b:329209576
BRANCH=None
TEST=Boot image on SKU1/SKU2 and check S0ix working.
Change-Id: Iabd0b3a83aa386e09310b671632368807a4018d4
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Modeled after the Rex Kconfigs for ISH.
Change-Id: Ic670d550a9aaad64e52489d895b8aac2aee4b5ed
Signed-off-by: Yuval Peress <peress@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81050
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that EC software sync has been verified to work on Brox, we can
enable it by default.
BUG=b:326152804
BRANCH=None
TEST=Verify that SW sync occurs
Change-Id: I3d356c006fc448125605761f7328d1f1e203a7c4
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81211
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For SKU1, wake pin is WLAN_PCIE_WAKE_ODL.
Update gpio config and corresponding ACPI for WoWLAN.
BUG=b:327379404
BRANCH=None
TEST=Boot image on SKU1 and check Wake on WLAN from S0ix.
Change-Id: I04c35da2c9ac57cafdf7f7a35d83ab2e7a05fe4a
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
For boot beep functionality, relevant register values are
required to be updated.
BUG=b:324528901
BRANCH=None
TEST=Build & verified Boot Beep functionality on Brox
Change-Id: If236c8ac173a279db676af412377fa4e4122c1cd
Signed-off-by: poornima tom <poornima.tom@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80416
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Early EC Sync does not need to be enabled in coreboot as EFS2 is being
enabled in the EC.
BUG=b:326152804
BRANCH=None
TEST=emerge-brox coreboot
To be tested with EC sync enabled
Change-Id: I08bdbe9f3dcea837b0b148adc137c03d3461877a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80689
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DPTF functionality for brox board
BRANCH=None
BUG=b:324360936
TEST=Built and tested on brox board
Change-Id: I0315f7f45688ccc36d321d6be4fa4fac7559a16b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Change-Id: Id859c981d0bf5dcf90bf6858607a9fe726516309
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
For devices that require CNVi Bluetooth select WIFI_BT_CNVI
in FW_CONFIG. Discrete Bluetooth devices need to select
WIFI_BT_PCIE.
BUG=b:319188820,b:325084796
BRANCH=None
TEST=Boot image on SKU1,SKU2 and check BT devices enumerate.
Change-Id: Iba008682fcfa7ddc1ec400649c8742c721666f1d
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80564
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Setting the EC interrupt GPIO as an APIC is able to solve many
problems that we are currently seeing:
1. Routing through the APIC make the IRQ# associated with this pin
unavailable to claim for other devices in the kernel. This is causing
EC interrupts to not work.
2. Since EC interrupt are not working, we are not able to flash the
EC from the DUT.
3. Also, the GPI_INT configuration does not allow us to set the
polarity of the GPIO, which means that it is by default set as active
high. As a result, we are seeing an excessive number of host command
interrupts to the EC. This disappears when we change the
configuration to APIC and set the polarity as INVERT.
BUG=b:319129926,b:324707182
BRANCH=None
TEST=1. After boot up, check if ec_cros_lpcs driver was successfully
registered. Look for the following string:
"cros_ec_lpcs GOOG0004:00: Chrome EC device registered"
2. Make sure can flash the EC image from the DUT
3. Make sure EC console is not getting continuous stream of host
commands.
Change-Id: I74bff88d2ddbaf1f4b085c31d582bd66e18c438a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80467
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ashish Kumar Mishra <ashish.k.mishra@intel.corp-partner.google.com>
|
|
Set the display type for the LCD panel configured via the gfx/generic
driver. This will ensure the correct DID/device address are generated
in the SSDT.
Change-Id: If63374329ed5eb4330517ca1bf2ba1ada24fa54a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80244
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GMA driver generates the brightness controls expecting the name
LCD0, so we need to use it here as well so that the DSDT and SSDT parts
match.
Change-Id: Id52f7c0e542423ba08eeed89bf9b171e540e10e4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
TCHSCR_RST_L signal was originally being configured to 1 in gpio.c but
this was causing some leakage. Configuring it to 0 initially in
romstage fixes this. Also, make sure that EN_PP3300_TCHSCR is
initialized in romstage as well.
BUG=b:322249892
BRANCH=None
TEST=Make brox boots and touchscreen is still working
Change-Id: I5bf1901a3a40a38237b950abcb758f96aebcc1cf
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80300
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In case where PAD_CFG_GPI_INT() is initialized with a pin value
lower to PAD_CFG_GPI_IRQ_WAKE() for same GPIO community
the set_ioapic_used() is only called for the PAD_CFG_GPI_IRQ_WAKE() pin.
Due to this the IRQ associated with PAD_CFG_GPI_INT() is found free by
find_free_unique_irq() during IRQ assignment and assigned to other pins
which causes IRQ conflicts
BUG=b:322984217
BRANCH=None
TEST=Boot test on brox, check if correct IRQ assigned to EC
Change-Id: I8c3d557e888b8d0ceac203f49b702910fba26d6d
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80334
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the I2C configuration to match the usage such that only required
I2C controllers are enabled.
BUG=b:319390850
TEST=Build Brox BIOS image and boot to OS. Ensure that only the required
I2C controllers are enabled.
Change-Id: I9f24beb9ef587163362cc6ded88efb05be1329b9
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80303
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Brox, HDA Codec used is ALC256. Add verb table for the same. Also,
add the related device tree changes for HDA related registers.
Realtek High Definition Audio Configuration-
Version : 5.0.3.1
BUG=b:317398558
BRANCH=None
TEST=verified HDA on Brox.
HDA Sound cards detected. Headphone working verified.
Device listed under sysfs as below:
cat /sys/bus/hdaudio/devices/ehdaudio0D0/chip_name
ID 256
cat /sys/bus/hdaudio/devices/ehdaudio0D0/vendor_name
Realtek
Change-Id: I1edd5aee053debe39b34048266703031c088cd00
Signed-off-by: Poornima Tom <poornima.tom@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79723
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This renames bus to upstream and link_list to downstream.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I80a81b6b8606e450ff180add9439481ec28c2420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
BUG=b:300690448,b:319393777
BRANCH=None
TEST=tested on a device with i2cdetect
Also tested with evtest and make sure Wacom is listed
Change-Id: I4f528b0d778c8c4a4e83774d5c167ccb2d6afd9a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79895
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is causing an assertion error on the devices that don't have CNVi
enabled because CNVi is hidden behind a FW_CONFIG flag in the
overridetree now.
BUG=b:319188820
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
make sure we can boot to kernel on device.
Change-Id: Ifcfbc04825d4d4e7f2874a4c52f9c5cf3e657856
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80211
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There was a mistake in the gpio spreadsheet provided by the HW team
and the GPIO assignments for the EC INT and WAKE signals got switched
from what it was in the schematics. The correct assignments are:
GPP_D0 = EC_PCH_INT_ODL
GPP_D1 = EC_PCH_WAKE_ODL
BUG=b:311450057,b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Will try to boot OS image on device and see if there are any
ec errors.
Change-Id: I02057aeb5d82218dbbe4c939d4feb87a4d3da678
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79886
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I5855f49984db59d786decad6142e3525b146a573
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80105
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
We need to disable the cnvi device when pcie wifi is enabled, so need
to use the FW_CONFIG defined in the overridetree for this.
BUG=b:311450057,b:300690448,b:319188820
BRANCH=None
TEST=This will be tested on the device when received
Change-Id: If9e861db37e321fd69c09f9b4aafa2e212f92caa
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79898
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:311450057,b:300690448,b:319188820
BRANCH=None
TEST=test on device with lspci
& make sure can see the Intel Network controller
Change-Id: I361bef13ebd073b6fccb729a1960d3832cf2681a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Add get_wifi_sar_cbfs_filename(). This function uses the FW_CONFIG
for WIFI to choose the right wifi_sar hex file. Below is the file
mapping:
wifi_sar_0.hex = wifi6
wifi_sar_1.hex = wifi7
BUG=b:319302319
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
Change-Id: I212c80412141e7770a512bd8ccf4111963bab395
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80085
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Primus4es board is no longer supported thus drop it from the tree.
TEST=Build all Brya boards in CrOS-SDK - Primus4ES not built. No negative impact observed.
Change-Id: I0502b2eed6f80d648b422c8d1622d504a6c93822
Signed-off-by: Jakub Czapiga <czapiga@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
I got confused and used UFS (User Facing Side) for the User Facing
Camera (UFC) in the FW_CONFIGs. Change references of the camera from
UFS --> UFC.
BUG=b:300690448
BRANCH=None
TEST=None. The camera has not been enabled yet.
Change-Id: I4f8240ae51aad1e077f325a9eab5a2a92f1402cb
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79997
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These are specific to the brox board, so moving devices to the brox
variant.
BUG=b:311450057,b:300690448,b:319058143
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
will check if this helps detect the storage device in the factory
Change-Id: I18d096040c293abfd4cd0b1bb5f50ba6dcc2e183
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Brox project has FW_CONFIG bits already set up in the project file for
the retimer and for storage, so make sure that the brox device tree
matches those settings.
BUG=b:311450057,b:300690448,b:319058143
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
will check if this helps detect the storage device in the factory
Change-Id: Iaf43003b7e8210eee9016d779839d7048c15825f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79854
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:311450057,b:300690448
BRANCH=None
TEST=to be tested on a device with i2cdetect
Change-Id: If6da1c722e87a50c6d422b300f16a52d884fa08f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This is needed for NVMe to work when PCIe device is connected to the
CPU side of RPL soc.
BUG=b:311450057,b:300690448, b:319058143
BRANCH=None
TEST=Tested on device and was able to boot to the OS
Change-Id: Ic8a1fdcedf2ec6c7bf1dd00e02ef7c13e9338aac
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This needs to be disabled for RPL otherwise we'll hit the assertion:
[EMERG] ASSERTION ERROR: file 'src/soc/intel/alderlake/fsp_params.c', line 1066
There is a comment in the referenced file/line in the assertion that
says that "C state demotion must be disabled for Raptorlake J0 and Q0
SKUs." So, disabling it.
BUG=b:311450057,b:300690448
BRANCH=None
TEST=Tested that we didn't hit this assertion on the device after this
change
Change-Id: Ib7b2484de2d84c980550fd951f1e30efab0ee197
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79855
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The DQS mapping for DIMM idx 6 was discovered to be incorrect to what
was in the schematics. Correcting the mistake in this CL.
BUG=b:311450057,b:300690448
BRANCH=None
TEST=tested on device and it passed memory training
Change-Id: I21f50e2f5b4fae09725c1c7532636ed1cc1a9043
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79843
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Add GFX devices for DDI (eDP and HDMI) and TCP (USC C0 and C2
ports). Copied the PLD placements from USB PLDs.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: Ic39916819f64ede1c80eccfd05ba4916b9f285af
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Some GPIOs were not configured correctly according to the HW
spreadsheet provided by the HW team.
* GPP_B5/GPP_B6 use NF1, not NF2
* GPP_B23 should use NF2, no GPI
* GPP_D11 should be set to NC
* GPP_E21/22 should be using NF (previous NC)
* GPP_F17 is a GPO
* GPP_F18 should be an interrupt, not a NF
BUG=b:300690448,b:316180020
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: I9e1e62adb79bd7fdab935afdbf2d23f9061b88aa
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Did a pass through HW team's brox speadsheet and aligned the gpio.c
file with it. The changes in this CL are to fix the pad's reset field
as needed. See "Intel SoCs" section in
https://doc.coreboot.org/getting_started/gpio.html for reset
definitions.
BUG=b:300690448,b:316180020
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: I4285136184c648adb9dc97748bd6b01cba3f8ddd
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79579
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Did a pass through HW team's brox speadsheet and aligned the gpio.c
file with it. The changes in this CL include fixing the pulls for
GPIOs as necessary, making sure that it matches what is in the HW
team's spreadsheet.
BUG=b:300690448
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: Ie50cb3c6fc85f1633c1afd1330c0e040e04b0ec1
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79704
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Did a pass through HW team's brox speadsheet and aligned the gpio.c
file with it. The changes here include changing the pad config to NC
because it is not being used in ChromeOS.
BUG=b:300690448
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: I15471e4d7ff25c858b05ef024f15ca7c0b9e598e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79703
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some of the boards use the EC_SYNC pin to wake the AP but do not
advertise the pin as wake capable in the CREC _CRS resource. Relevant
boards were determined through empirical testing and inspection of gpio
configuration.
Update the ACPI tables for rex, brya, and brox based boards to advertise
their EC_SYNC pin as wake capable.
BUG=b:243700486
TEST=-Dump ACPI and verify ExclusiveAndWake share type is set when
EC_SYNC_IRQ_WAKE_CAPABLE is defined
-Wake Aviko via keypress and verify chromeos-ec as wake source
-Wake Screebo via lid open and verify chromeos-ec as wake source
Change-Id: I5828be7c9420cab6ae838272c8301c302a3e078c
Signed-off-by: Mark Hasemeyer <markhas@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79374
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
FSP default value for LpDdrDqDqsReTraining is 1. For boards
that didn't set LpDdrDqDqsReTraining to any value, 0 was being
assigned and it caused black screen issue.
BUG=b:311450057
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: I4a009076e50408a4f7ff16ddc96a0f2e47b09470
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79646
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
For initial debugging, we want to disable SW syncing. Will re-enable
in the future.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
run gbb_utility --get --flags <image>
make sure that it returns 0xa39
Change-Id: I865e9585ab37d1328a0ff54c6343cdad2c02220c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79569
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Keith Short <keithshort@chromium.org>
|
|
Add the MICRON MT62F1G32D2DS-023 WT:B RAM part for brox:
DRAM Part Name ID to assign
MT62F512M32D2DR-031 WT:B 0 (0000)
H9JCNNNBK3MLYR-N6E 0 (0000)
MT62F1G32D4DR-031 WT:B 1 (0001)
MT62F1G32D2DS-023 WT:B 2 (0010)
BUG=b:311450057,b:315913909
BRANCH=None
TEST=Run part_id_gen tool without any errors
Change-Id: Id120a5eb311d8299a8e59d2c1658fe0742e93934
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Update brox devicetree based on the latest schematics.
- Configure typeC to EC mux ports settings.
- Configure USB2/USB3 ports settings.
- Configure TCSS ports settings.
BUG=b:311450057
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: Iac5a2e8be6cea64f107d267d4cf71529f08bb63d
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79391
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the support LP5 RAM parts for brox:
1. HYNIX LPDDR5 6400 2GB H9JCNNNBK3MLYR-N6E
2. MICRON LPDDR5 6400 4GB MT62F1G32D4DR-031 WT:B
DRAM Part Name ID to assign
H9JCNNNBK3MLYR-N6E 0 (0000)
MT62F1G32D4DR-031 WT:B 1 (0001)
BUG=b:311450057
BRANCH=None
TEST=Run part_id_gen tool without any errors
Change-Id: Ib17f26a310435e37088191594863a645aa751440
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79392
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Fix up the memory config for brox based on the schematics. Also,
since memory training needs to happen in romstage, initializing the
MEM_STRAP & MEM_CH_SEL gpios for use in romstage. Also consolidating
the GPIOs needing to be initialized in romstage into the baseboard
gpio.c file.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: I17615cda7df10e73e49fb49f736728787ef7625d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Brox has SSD and UFS storage per different SKU.
1. Set SSD on CPU PCIe port (PCIEX4_A) and configure related gpio
settings according to the schematic.
2. Enable UFS, also enable ISH since it is PCI function 0, required
for UFS function 7 to be enabled.
3. Set unused SRCCLKREQ signals to NC.
4. Remove unused gpio settings in variant gpio table to prevent
unexpected overrides.
BUG=b:311450057
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: I88922bcfa13652006aa10078c3c444624fd4575e
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79295
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Brox, TPM is using i2c4 and GPP_E2, so modifying the Kconfig to
reflect this. Also, fixing up the TPM entry in the device tree.
Making sure that the GPIO for GSC_PCH_INT_ODL is set correctly.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: I0ecaa6fcfc05c3c2e55f857d7a4e59fe46096bb5
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79102
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Brox is using Ti50, so make sure that we set the right config for that.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: If4a16448eebc028b2989c1de150b9e0f9067ee92
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Assigning the macros in gpio.h to the correct GPIOs. Also, fixing GPE
configurations so that they are mapped to the proper wake sources
(GPP_B, D, E groups).
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: I6320cd98e560e514e63c52e173cb7923cfd1cdee
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
All of these signals have net names, but are actually unstuffed, so we
have to set them to NC.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: I27d8b7cd02aefb49a2dc031a30eb0d1e8aa9faa9
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The symbol VBT_DATA_SIZE_KB was removed in commit 8bde652241 -
"drivers/intel/gma/opregion: Use CBFS cache to load VBT" CB:77886,
however that patch only removed the Kconfig option from the Intel
chipsets, leaving it unused in the mainboards.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ia29d8d6ec17b172e662ff591849f1668d65f1ff9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78967
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Later GSCs don't need a EC_IN_RW GPIO anymore, so removing the use of
this for get_ec_is_trusted().
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: I29f94969e9f2c1f239d9f9655f39b8410296f695
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Some GPIOs (like WP and GSC) need to be configured in bootblock.
Making sure that they get configured earlier for this.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: I8dd4853bc05b954f47d858d87ea2aed48e4b8074
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78943
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are some inaccuracies in arbitrage. This is the first pass at
correcting the incorrectly generated configs. I also tried to update
the "No heuristic was found useful" comment generated by arbitrage
into something more useful (ie: the appropriate NFs).
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: I836565e09a3e0b25746b3e2f9ed6610eaacf7e97
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78942
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the required FMD changes to support the change
in cse_lite 'commit Ie0266e50463926b8d377825 ("remove
cbfs_unverified_area_map() API in cse_lite")' for CBFS verification.
With the change in cse_lite the ME_RW_A/B blobs are now part of
FW_MAIN_A/B and corresponding entries in FMD can be removed for boards
that currently use them.
BUG=b:284382452
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I3ca88fee181f059852923d50292b24c0e5b9fd6d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
