Age | Commit message (Collapse) | Author |
|
Took less than 30 minutes, and booted on the first try :)
Working:
- Native raminit, using two 2GB DDR3-1333 DIMMs
- S3 suspend/resume
- USB ports and headers
- EHCI Debug with an FT2232H
- Gigabit Ethernet
- Integrated DVI/VGA outputs (libgfxinit)
- PCIe x16 for a graphics card
- PCIe x1 ports
- PS/2 port with a keyboard
- SATA controller
- Audio outputs, both front and rear
- flashrom, using the internal programmer. Tested with coreboot,
as well as with the vendor firmware. Backup chip is untested.
Untested:
- VGA BIOS for integrated graphics init
- Audio inputs
- Non-Linux OSes
- ACPI thermal zone and OS-independent fan control
Not working:
- Default IFD defines the BIOS region as the entire flash chip.
Using 'flashrom --ifd -i bios' is asking for a failed flash!
Change-Id: I467f586530e4a3b53a24b66565b5dcab5e33cf46
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Tested with SeaBIOS as a payload, booting Arch Linux with
a Linux kernel. The new code is based on autoport and the
existing GA-H61M-S2PV code.
The GA-H61M-S2PV has been boot-tested too, it still boots.
Working:
- S3 suspend/resume
- USB ports and headers (Intel USB2 and EtronTech USB3)
- Gigabit Ethernet
- Integrated DVI/VGA graphics (libgfxinit)
- PCIe x16 graphics
- PCIe x1 ports
- PS/2 port with a keyboard
- SATA controllers (Intel SATA2 and Marvell SATA3)
- User-space fan control (fancontrol on Linux)
- Native raminit (4+4GB DDR3-1333)
- flashrom, using the internal programmer. Tested with coreboot,
as well as with the vendor firmware. Backup chip is untested.
Untested:
- VGA BIOS for integrated graphics init
- Audio: Only front/read outputs has been tested.
- Non-Linux OSes
- ACPI thermal zone and OS-independent fan control
Not working:
- Default IFD defines the BIOS region as the entire flash chip.
Using 'flashrom --ifd -i bios' is asking for a failed flash!
Change-Id: I37928de158bb8fbb47fbda5d1ccd4efba7edab26
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Tested with GRUB 2.02 as a payload, booting Arch Linux with
latest kernel. This code is based on the output of autoport
as well as existing ga-b75m-d3h and ga-b75m-d3v mainboards.
Working:
- Serial port I/O
- S3 suspend/resume (broken with SeaBIOS 1.11.1)
- USB ports and headers
- Gigabit Ethernet
- Integrated graphics (libgfxinit)
- PCIe x16 graphics
- PCIe x1
- SATA controller
- Hardware Monitor
- Fan Control (fancontrol on linux works well)
- Native raminit (4+4GB, 4+2GB, 2+2GB, DDR3-1333)
- Native graphics init with libgfxinit
- flashrom, using the internal programmer. Tested with coreboot,
as well as with the vendor firmware. Backup chip is untested.
- NVRAM settings. Only `gfx_uma_size` and `debug_level` have been
tested with values different from the default.
Untested:
- VGA BIOS for integrated graphics init
- DVI port. It can detect a "fake" display, that is, an
EEPROM connected to the DVI port.
- PS/2 ports
- Audio: Only rear output (green) has been tested.
- EHCI debug.
- Parallel port
- Non-Linux OSes
- ACPI thermal zone and fan control (probably not working)
Not working:
- SATA devices with Tianocore (payload issue)
- PCIe to PCI bridge. It seems to be poorly supported on Linux,
it lacks a public datasheet and vendor BIOS behaves in the
same way: The bridge and the devices behind it appear, but
drivers fail to find devices attached to the bridge.
Change-Id: I598a0b75093a0f1aef2ac615035d66786a8c22cb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/25912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|