| Age | Commit message (Collapse) | Author |
|---|
|
Add a devicetree option to set temperature adjustment registers
required for thermal diode sensors and PECI. However, this commit does
not have the code needed to make PECI interface actually use these
registers. It only applies to diodes.
As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin
to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3".
PECI, apparently, takes precedence over diode, so the adjustment register
will be set and PECI activated. Or simply use the followup patch, which
makes THERMAL_PECI a mode like THERMAL_DIODE.
I don't have hardware to test THERMAL_DIODE mode, but in case of PECI,
without this patch I had about -60°C on idle. Now, with offset 97,
which was taken from vendor bios, PECI readings became reasonable 35°C.
TEST=Set a temperature offset, then ensure that the value you set is
reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset
Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ifba821a7e355a0d6689f21c7f307e3901903a3fd
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17602
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Although the goal was to hide the ME device by disabling
the PCI bridge, the original comment that this bridge was ME related
was a mistake, this bridge is for PEG not for ME.
We still need this PCI bridge "on" to enable pci express graphics
add-on cards.
Change-Id: Ibf322136097d77a8e7c05dcb14f72da938187a0a
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16496
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Previously, due to a bug in devicetree and incorrect IRQ
settings in ACPI, SATA controller would not initialize
any HDDs in the OS, even though it worked in SeaBIOS.
The devicetree setting is not needed because SATA must
function in "plain" mode on this board, as "combined" mode
does not work at all.
Change-Id: I0036c4734de00b84cc3d64f38e4b1fd80fd1a25d
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/14776
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I5b6edbd97d4e6ed8b03f2f319a338022647e26ea
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13465
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Board uses x4x native raminit
Board boots into Debian 8 with full graphics
IRQ9: nobody cared, gets disabled
(PIC needs IRQ settings?)
VGA:
- VGA native init works in grub with analog connector
- Fails to boot with both channels of ram populated
Change-Id: I7417813456817529b8cbaace45cefe47467d0a82
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/11306
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
