Age | Commit message (Collapse) | Author |
|
The initial timestamps are now pushed on the stack when entering the
romstage C code.
Tested on Asus P5QC.
Change-Id: I88e972caafff5c53d8e68e85415f920c7341b92d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This removes the need to synchronize the devicetree and the romstage
writing to FD.
Change-Id: I83576599538a02d295fe00b35826f98d8c97d1cf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30244
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ibdff50761a205d936b0ebe067f418be0a2051798
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hellsenberg <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: David Guckian
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Field 'OEMID' & "OEM Table ID" are related to DSDT table
not to mainboard.
So use macro to set them respectvely to "COREv4" and
"COREBOOT".
Change-Id: I060e07a730e721df4a86128ee89bfe168c69f31e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Guckian
|
|
DSDT revision is =1 for ACPI v1 and =2 for greater ACPI version.
This will cause the AML interpreter to use 32-bit integers and math
if the version is 1, and 64-bit if the version is >=2.
Current spec version is 2 for ACPI 6.2-a.
Change-Id: I77372882d5c77b7ed52dcdd88028403df6f6fa7f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29626
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I801849fb31fe6958e3d9510da50e2e2dd351a98d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
On some boards the devicetree and Function Disable register did not
match. In this case the FD values are put in the devicetree as these
were the values that were actually used in practice.
A complete devicetree will make it easier to automatically disable
devices in ramstage.
Change-Id: I1692ca5f490ea84e2fc520d3f66044ad7514f76e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Instead of having the code for the RAM init time stamps in each
mainboard’s `romstage.c`, factor it out to the northbridge code, done in
commit 771328f7 (intel/i945: add timestamps in romstage).
Change-Id: Ibb699a1fea2f0b1f3c6564d401542d2fb3249f5a
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/17994
Reviewed-by: Elyes HAOUAS <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Used default console log level is 7 in src/console/Kconfig.
So let cmos.default use the same level as default.
Change-Id: Ia39ee457a8985142f6e7a674532995b11cb52198
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I3108193c0e0b644cecb74ae0c7a7b54e24a75b58
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I80dd65484fd52e9048635091fb20a123e959e999
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27869
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Both southbridges need to be done at once since this southbridge code
is used for different northbridges, which fails to compile when done
separately.
This needs an acpi_name functions in the northbridge code to be
defined.
TESTED on Intel DG43GT: show correct PIRQ ACPI entries in
/sys/firmware/acpi/tables/SSDT.
Change-Id: I286d251ddf8fcae27dd07011a1cd62d8f4847683
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Shuffle words and drop the _DATA_FILE suffix.
Change-Id: I0b0d50ea729e5580c0bc7b43f250ff387ce59cfc
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: If1f032d097224a1102ba29d8d45dce46aad3a91a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
These files are directly extracted from the vendor firmware.
Change-Id: I1dea2843255e4a3e93fbb734dea284be029dbc45
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/26654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Fix the values that were off by one.
This was discovered when using postcar stage that prints with
debuglevel BIOS_NEVER.
Change-Id: I73a077950ed0dc735d89c9747a8da0a25f30822d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The PNOT method never notifies the CPU to update it's _CST methods due
to reliance on inexisting variable (PDCx).
Add a method in the speedstep ssdt generator to notify all available
CPU nodes and hook this up in this file.
The cpu.asl file is moved to cpu/intel/speedstep/acpi since it now
relies on code generated in the speedstep ssdt generator. CPUs not
using the speedstep code never included this PNOT method so this is
a logical place for this code to be.
Change-Id: Ie2ba5e07b401d6f7c80c31f2bfcd9ef3ac0c1ad1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Things cleaned up in this patch:
* Add macros for the GENx_DEC registers;
* replace many magic numbers by macros;
* remove many writes to DxxIP since they were 'setting' reset default
values;
* fix some comments about decode ranges.
Change-Id: I9d6a0ff3d391947f611a2f3c65684f4ee57bc263
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add a devicetree option to set temperature adjustment registers
required for thermal diode sensors and PECI. However, this commit does
not have the code needed to make PECI interface actually use these
registers. It only applies to diodes.
As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin
to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3".
PECI, apparently, takes precedence over diode, so the adjustment register
will be set and PECI activated. Or simply use the followup patch, which
makes THERMAL_PECI a mode like THERMAL_DIODE.
I don't have hardware to test THERMAL_DIODE mode, but in case of PECI,
without this patch I had about -60°C on idle. Now, with offset 97,
which was taken from vendor bios, PECI readings became reasonable 35°C.
TEST=Set a temperature offset, then ensure that the value you set is
reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset
Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
There have been discussions about removing this since it does not seem
to be used much and only creates troubles for boards without defaults,
not to mention that it was configurable on many boards that do not
even feature uart.
It is still possible to configure the baudrate through the Kconfig
option.
Change-Id: I71698d9b188eeac73670b18b757dff5fcea0df41
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I8febb8d74e2463622cab0313c543ceebec71fdf4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I15550b1cc1a7ccfecba68a46ab2acaee820575b9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
All boards select INTEL_EDID, move it to nb folder.
Change-Id: I35f075a87f2d841856b208f9440cf41af6a3c8e6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19086
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is more consistent with newer Intel targets.
This a static struct so it is initialized to 0 by default.
To make it more readable:
* only setting to GPIO mode is made explicit;
* only pins in GPIO mode are either set to input or output since this
is ignored in native mode;
* only output pins are set high or low, since this is read-only on
input;
* blink is only operational on output pins, non-blink is not set
explicitly;
* invert is only operational on input pins, non-invert is not set
explicitly.
Change-Id: I05f9c52dee78b7120b225982c040e3dcc8ee3e4e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17639
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Currently, some Intel 945 boards miss some or all of the time stamps
*1:start of rom stage*, *2:before ram initialization*, and *3:after ram
initialization*, so add them.
Use the same formatting as used for the board Lenovo X60, which already
has code for all the time stamps.
Change-Id: Ie25747d02fadd74b7d7b7cab234a7a88b2cc0c42
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/17993
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Checking for memory self refresh can generate false positives,
as explained in faa6beb: "northbridge/intel/i945:
CHECK_SLFRCS_ON_RESUME Kconfig option".
This seems to be the case for this motherboard.
TESTED on ga-945gcm-s2l.
Change-Id: Iadf0a73b054470b652e1dc02557fb1715131f823
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17617
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Instead of hardcoding pci_mmio_size in the raminit code,
this makes it a parameter in the devicetree.
A safe minimum of 768M is also defined since using anything
less causes problems (if 4G of ram is used).
Change-Id: If004c861464162d5dbbc61836a3a205d1619dfd5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16856
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ic22beaa47476d8c600e4081fc5ad7bc171e0f903
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17735
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This mainboard is identical to ga-945gcm-s2l except for NIC
which is a Realtek RTL 8101E chip (10/100 Mbit).
The schematics of ga-945gcm-s2l mention multiple NICs and ga-945gcm-s2c
and ga-945gcm-s2l have a common manual further indicating that those
boards are close to identical.
Change-Id: Iba3d401efcf208154e639c3237b201830a5151aa
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17416
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Id7c2b656f500c14f39d4492667ea461b9ca353b0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17613
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I021aae6130c475cb370b891ffaec6f1ad267540b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17580
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
GPIO register at offset 0xfc (VID Input Register) is read-only but
writing 1 to bit 0 will update initial VID input.
Change-Id: Ie372e98f8e497eede382975262a63d58c16227b9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17412
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Startpoint was Intel d945gclf, which has same chipset and
Gigabyte ga-g41m-es2l which has same Superio.
What works and is tested:
* PCI slot;
* PCIe x16 slot with GPU (RADEON HD 2600 XT) and ADD2 DVI card;
* onboard VGA output (only textmode implemented) with native graphic init;
* 533, 800, 1067MHz FSB CPU (1333MHz is unsupported by the chipset);
* serial output during and after boot.
What does not work:
* resume from suspend (does not work for d945gclf either).
Quirks:
* The Realtek ethernet card requires a reset which currently also
hardcodes a MAC adress.
This board was only tested with the SeaBIOS payload due to flash size
constraints (512KB) and with GNU/Linux.
Change-Id: I0ff9f193105facc1b276a791790e27eb4c275085
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17033
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|