| Age | Commit message (Collapse) | Author |
|---|
|
Add a devicetree option to set temperature adjustment registers
required for thermal diode sensors and PECI. However, this commit does
not have the code needed to make PECI interface actually use these
registers. It only applies to diodes.
As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin
to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3".
PECI, apparently, takes precedence over diode, so the adjustment register
will be set and PECI activated. Or simply use the followup patch, which
makes THERMAL_PECI a mode like THERMAL_DIODE.
I don't have hardware to test THERMAL_DIODE mode, but in case of PECI,
without this patch I had about -60°C on idle. Now, with offset 97,
which was taken from vendor bios, PECI readings became reasonable 35°C.
TEST=Set a temperature offset, then ensure that the value you set is
reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset
Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Instead of hardcoding pci_mmio_size in the raminit code,
this makes it a parameter in the devicetree.
A safe minimum of 768M is also defined since using anything
less causes problems (if 4G of ram is used).
Change-Id: If004c861464162d5dbbc61836a3a205d1619dfd5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16856
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Id7c2b656f500c14f39d4492667ea461b9ca353b0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17613
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Startpoint was Intel d945gclf, which has same chipset and
Gigabyte ga-g41m-es2l which has same Superio.
What works and is tested:
* PCI slot;
* PCIe x16 slot with GPU (RADEON HD 2600 XT) and ADD2 DVI card;
* onboard VGA output (only textmode implemented) with native graphic init;
* 533, 800, 1067MHz FSB CPU (1333MHz is unsupported by the chipset);
* serial output during and after boot.
What does not work:
* resume from suspend (does not work for d945gclf either).
Quirks:
* The Realtek ethernet card requires a reset which currently also
hardcodes a MAC adress.
This board was only tested with the SeaBIOS payload due to flash size
constraints (512KB) and with GNU/Linux.
Change-Id: I0ff9f193105facc1b276a791790e27eb4c275085
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17033
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
