| Age | Commit message (Collapse) | Author |
|---|
|
Things cleaned up in this patch:
* Add macros for the GENx_DEC registers;
* replace many magic numbers by macros;
* remove many writes to DxxIP since they were 'setting' reset default
values;
* fix some comments about decode ranges.
Change-Id: I9d6a0ff3d391947f611a2f3c65684f4ee57bc263
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Especially on ICH7 failing to do so results in i2c block read being
unusable. On ICH10 this problem doesn't manifest itself that much.
This moves disabling the watchdog reboot to the northbridge code like
i945 (even though it technically is southbridge stuff).
TESTED on Intel DG41WV: hacking on raminit is much nicer since no
need to do a hard power down for +4s are needed to clear the timeouts.
Change-Id: Icfd3789312704f61000a417f23a121d02d2e7fbe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add a devicetree option to set temperature adjustment registers
required for thermal diode sensors and PECI. However, this commit does
not have the code needed to make PECI interface actually use these
registers. It only applies to diodes.
As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin
to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3".
PECI, apparently, takes precedence over diode, so the adjustment register
will be set and PECI activated. Or simply use the followup patch, which
makes THERMAL_PECI a mode like THERMAL_DIODE.
I don't have hardware to test THERMAL_DIODE mode, but in case of PECI,
without this patch I had about -60°C on idle. Now, with offset 97,
which was taken from vendor bios, PECI readings became reasonable 35°C.
TEST=Set a temperature offset, then ensure that the value you set is
reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset
Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
There have been discussions about removing this since it does not seem
to be used much and only creates troubles for boards without defaults,
not to mention that it was configurable on many boards that do not
even feature uart.
It is still possible to configure the baudrate through the Kconfig
option.
Change-Id: I71698d9b188eeac73670b18b757dff5fcea0df41
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Based on the Intel G41 chipset, ICH7 southbridge, and IT8720F Super I/O.
Tested, working:
* Booting Linux 4.11.3 and Windows 8.1 from USB and HDD
* Resume from S3 (Linux and Windows)
* Native raminit (DDR2-800)
* Native graphics init (SeaBIOS, Linux)
* Graphics init with VGA BIOS (SeaBIOS, Windows)
* PCI-E x16 PEG slot, PCI-E x1 slot from southbridge
* Realtek ALC888 HD Audio (including front panel and jack detection)
* Realtek R8168 Gigabit LAN
* Both SATA ports
* USB 1.1 and 2.0 devices (keyboard, mass storage)
* PC speaker beep
* COM header
* Super I/O Environment controller (temps, voltage, fans)
* PS/2 keyboard and mouse
* Flashing with `flashrom -p internal`
* 1MiB and 2MiB SPI flash chips
* CMOS gfx_uma_size
Appears, OS driver loads, but otherwise untested:
* IrDA header
* CIR header
* TPM header
Untested:
* S/PDIF digital audio
Tested, known broken:
* CMOS power_on_after_fail
* USB keyboard in secondary payloads
Change-Id: Ifc4c8935b1a11e55f4bf6cfa484a8a8d09b1adda
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20027
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
