| Age | Commit message (Collapse) | Author |
|---|
|
For anyone who knows the difference between a header and a variable in C
these depictions are rather useless. Thus, these lines wast essential
screen real estate while working on coreboot.
Change-Id: I7fe55d936c035ef83832716c45bfc57d73c0edc7
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5979
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Use the following command to fix all occurences.
$ git grep -l approriate | xargs sed -i 's/approriate/appropriate/g'
Change-Id: I4cbba972bb445c2407ef2e63ffb3068fc948f1c6
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/5987
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The PCI_INTR table is an Index/Data pair of I/O ports
0xC00 and 0xC01. This table is responsible for physically
routing IRQs to the PIC and IOAPIC. The settings given
in this table are chipset and mainboard dependent, so the
table values will reside in the mainboard.c file. This
allows for a system to uniquely set its IRQ routing.
The function to write the PCI_INTR table resides in
cimx_util.c because the indices into the table have
the same definitions for all SBx00 FCH chipsets.
The next piece is a function that will read the PCI_INTR
table and program the INT_LINE and INT_PIN registers in
PCI config space appropriately. This function will read
a devices' INT_PIN register, which is always hardcoded to
a value if it uses hardware interrupts. It then uses this
value, along with the device and function numbers to
determine an index into the PCI_INTR table. It will read
the table and program the corresponding value into the PCI
config space register 0x3C, INT_LINE. Finally, it will set
this IRQ number to LEVEL_TRIGGERED on the PIC because it is
a PCI device interrupt and the must be level triggered.
For example, the SB800 USB EHCI device 0:18.2 has an INT_PIN
value hardcoded to 2. This corresponds to PIN B. On the
Persimmon mainboard, I want the USB device to use IRQ 11. I
will program the PCI_INTR table at index 0x31 (this USB device
index) to 11. This function will then read the INT_PIN register,
read the PCI_INTR table, and then program the INT_LINE register
with the value it read. It will then set the IRQ on the PIC to
LEVEL_TRIGGERED by writing a 1 to I/O port 0x4D1 at bit position 4.
Also, the SB700 has slightly different register definitions than
the newer SB800 and SB900 so it needs its own set of #defines for
the pci_intr registers.
Only the Persimmon mainboard is adapted to this change as an
example for other mainboards.
Change-Id: I6de858289a17fa1e1abacf6328ea5099be74b1d6
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/5877
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: I5df1f0efdef2592b762fe391edaadbca4593e85a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5689
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I9c8f7cc98c65102486e17ec49fa2246211dffc4f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5688
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ibbb07ef308c7e92a8a8dfe066f5e3866d5f8aee2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5687
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I158993bcb654ef27a9fc6b7e9dc3fc955fb740fa
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5686
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I3ac39441746d739ac19e831bb67c76405c24ba27
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5925
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
1. Remove #include .c in romstage.
2. Make romstage component symbols linker-time.
3. Provide header guards and prototypes in superio romstage support.
4. Correct function type-signatures to be static/non-static where
appropriate, avoid 'pretend optimisations' by unnecessarily inlining
functions.
5. Separate out UART enable from various other PNP hard coding
Change-Id: I9b8dad7c02d802e97db73ddf2913d5c6bb33a419
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5916
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
We now have common ite_*_*() functions for romstage and hence no longer
require the model specific portion of this superio support.
Change-Id: I30400abf27008a88072673075bba445f100d9ad3
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5838
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Change-Id: I2ff70cafdd808a235ed4f0663e182d306f493c7e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5685
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Removed function only read ACPI MMIO base address from a couple of
registers in IO space.
Change-Id: I25a31b7ac1706b9eebc5db0b9604039928328b0a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5683
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I9f27e1e814a80864d8ca315fe816a083c55708c6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5682
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Pass parameter Func like fam14, fam15tn and fam16kb.
Change-Id: I262bf88e431f7035e668ac8f3fb29ac0690b3e52
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5681
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This is x86 "standard" 0xcf9 reset mechanism.
Change-Id: Ieb48290b21a7cb1425881fdd65c794e96da0248f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5680
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Most of the callouts are not specific to board or even family.
Start new file with default callouts doing nothing and returning
either AGESA_SUCCESS or AGESA_UNSUPPORTED.
Also add callout for returning empty IdsIdData. This feature is
not used and could be easily overriden at board-level at later time.
Change-Id: I65dbcdd80dddc89d47669ebe62c22caa63792f5c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5678
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Spotted by Clang
Change-Id: I26201c7f5e421c38d3965d8e7e62c4a8e670e449
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5833
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
While at it, fix frontrunner-af board URL.
Change-Id: I3b631830d679abc20f8a72411f2402689d9f9aac
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5706
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
|
|
We should configure i8254/i8259 down in to the southbridge rather than
romstage of every AGESA/CIMx board much like Intel boards do.
Change-Id: Id7c4f0baa0819d52aef9b0ee03c20d0fa16b9352
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5669
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Following the reasoning of:
cf7b498 superio/fintek/*: Factor out generic romstage component
Change-Id: I4c0a9a5a7786eb8fcb0c3ed6251c7fe9bbbadae7
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5585
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Lines with 'select SERIAL_CPU_INIT' where redundant with the
default being yes. Since there is no 'unselect SERIAL_CPU_INIT'
possibility, invert the default and rename option.
This squelches Kconfig warnings about unmet dependencies.
Change-Id: Iae546c56006278489ebae10f2daa627af48abe94
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5700
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Already done for fam15tn and fam16kb.
Change-Id: I3da36bfe6fd1805867eee5aa1f017c4fda084349
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5660
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Heap allocation begins with BIOS_HEAP_MANAGER, no need to clear
the fields individually.
Change-Id: Ia1af84bd09d1edf8f72223752557d44a96dec6e1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5659
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Backported from fam15tn and fam16kb.
This also implements GetHeapBase() to satisfy some requirements
of HAVE_ACPI_RESUME for the following boards:
amd/inagua
amd/south_station
amd/union_station
asrock/e350m1
Change-Id: I488d063d4eabf4bf45bcbabd1e8f13b88b2ef401
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5658
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Backported from fam15tn and fam16kb.
Change-Id: I868352b32ff56a8386c615ab1a9f59e7e875292e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5657
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
While fam15 boards do not select HAVE_ACPI_RESUME, backport this
from fam14.
Implementation of this function is common across different families.
Change-Id: I222b418a0a79bbdf5f5cce6c876243ecb4912256
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5655
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
While amd/torpedo does not select HAVE_ACPI_RESUME, backport this
from fam14.
Implementation of this function is common across different families.
Change-Id: I0e5099a0991a2655ec2b6990929196900e842fc1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5654
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Implementation of this function is common for all boards in family,
and also across different families.
Change-Id: I562a132fa6d3ade2700d9a375d7aa21fcf8ea890
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5653
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Implementation of this function is common for all boards in family,
and also across different families.
Change-Id: I6aab710e76af9a361f0c0006922019a52feb3f6f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5652
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Backport from fam15tn and fam16kb.
Change-Id: I6d8f9a88f0dc43c36efb168c0111a6e2bcdda5fd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5651
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Backported from fam15tn and fam16kb.
Change-Id: I13ca70d141a46220a5d8ea7bb3898bc7d7258424
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5650
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Implemented under northbridge/ on other families.
Change-Id: I4d21af9d6c0f61eb1597e8e7095c08dd87ae2a84
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5649
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Although amd/torpedo is only fam12 board at the moment,
backported this from fam15tn and fam16kb.
Change-Id: I72a856e2eb455a8428a886f0c4217ff80e60eb78
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5648
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ic9c5e8abb3da020a642635ee74c9242091923619
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5628
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
In amd/{persimmon,inagua} and derived boards avoid using AGESA
reimplementation of memcpy as following the reasoning in:
e2f3bfc jetway/nf81-t56n-lf: Use std memset/memcpy func over AGESA
Change-Id: I943b46103c3bf1c5fd88b25e9f9595b9adfcafeb
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5625
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Some src/mainboard/*/*/romstage.c files use defines which later
modify the behaviour of included .c files.
Since it's a pain to work out what is affected by these, drop
values that are only defined in the board but never used, or
defined to identical values as in spd.h (and use that one instead).
Change-Id: I8143b26fddc32a40ac4e611a6287bf7f144267dc
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/5639
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
CONFIG_ARCH is a property of the cpu or soc rather than a property of the
board. Hence, move ARCH_* from every single board to respective cpu or soc
Kconfigs. Also update abuild to ignore ARCH_ from mainboards.
Change-Id: I6ec1206de5a20601c32d001a384a47f46e6ce479
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: http://review.coreboot.org/5570
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Following the reasoning of:
dbbc136 mainboard/asrock/e350m1: Avoid including early_serial.c
Change-Id: I5d729b90cf6713de2674fb00c726cd2944a3ab4e
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5597
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I24b2cbd671ac3a463562d284f06258140a019a37
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4683
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The romstage of Fintek Super I/O's is identical, leading to replication
of essentially the same code prone to bitrot. Herein we consolidate the
early pre-ram UART initialisation code into fintek/common, rather we
leave the exceptions to be implemented under model/.
More precisely we provide a well documented version of early_serial.c
under fintek/common and select by way of Kconfig as a generic romstage
component to Super I/O support. We leave future Super I/O's the option
to implement `non-standard` initialisation code should such a (unlikely)
need araise. A primary advantage is that new support for romstage serial
is now trival to add. We also provide some Kconfig documentation while
here.
Change-Id: I3c62561558a62ece944a167ba302fb7076bba001
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5575
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Dumping the ACPI tables in this way has limited use, is not likely to be
used and is poorly implemented. There are much more sophisticated tools
available on Linux for debugging ACPI as such this code is outside the
scope of coreboots 'bring up the hardware only' philosophy.
A more generic implemention could be done with hexdump() in coreboot
proper following on from this cleanup.
Change-Id: Ifd3bfb76338609d18fcf7158d3c9a6d7c06c8847
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5530
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Not very popular nor useful nowadays.
Change-Id: I3dc0f7aaf188950a43f5350d3a95669fbbdcfd94
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4554
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The power button was declared by hudson's ASL as \_SB.PCI0.PWRB, and
always had the wake source declared as GPE3. This is not the correct
wake source for all boards. On some laptops declaring a wake source is
not needed, as the wake mechanism is handled by the EC.
Move the declaration of the power button to mainboard ASL files, and
scope it as \_SB.PWRB . This also makes the naming consistent with the
examples in the ACPI spec. The wake source for the PWRB of HP Pavilion
M6 1035dx is removed, as it is incorrect.
Change-Id: I9c76566025e7f200c0376673f6c6ea299afa4a5d
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5546
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
|
|
Following boards use cimx/sb700:
amd/dinar
supermicro/h8qgi
supermicro/h8scm
tyan/s8226
Only amd/dinar had APIC_ID_OFFSET defined, thus all had 0x0.
There was a nonsense preprocessor directive (MAX_CPUS * MAX_PHYSICAL_CPUS >= 1).
Except for tyan, (MAX_CPUS * MAX_PHYSICAL_CPUS) % 256 == 0.
Together with documented 4-bit restriction for APIC ID field, this APIC ID
programming matches with MP tables and ACPI tables.
I believe this would also fix cases of cimx/sb700 with MAX_CPUS<16, which
we do not have in the tree.
Change-Id: If8d65e95788ba02fc8d331a7af03a4d0d8cf5c69
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5539
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
All boards had APIC_ID_OFFSET=0 and MAX_PHYSICAL_CPUS=1.
Change-Id: I6f08ea6de92a2af79fb3a99c5edd942b3a321c43
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5538
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
These are not used with cimx/sb900 vendorcode.
Change-Id: I489ee80c739b31edac649491497162c65316996e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5537
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: I81de291da7b3db8d04a127d5a304b558f1c75b34
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5535
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The MMIO region is set up by AGESA very early on, so we can use it to
access the PM register space in ramstage. 16-bit accessors are also
provided to simplify some setup tasks. 16-bit accesses are not
possible via PIO.
The pm2_iowrite/read accessors are removed, as they are not used.
Change-Id: Ie7967b5086eb004525c39721338c6495aedc8165
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5503
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
|
|
Not used with AGESA vendorcode.
Change-Id: I4de7e49d513a1bc8d6d4da1eea630b9eedf5de80
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5522
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Not used with AGESA vendorcode.
Change-Id: I1c4e1dea8836143334d336f99afcee2ca326b0c9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5521
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Not used with AGESA vendorcode.
Change-Id: Ic9a0513641bf76d748bb106675bccc33c7abe21e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5520
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Not used with AGESA vendorcode.
Change-Id: Ie99abf5bcffd740e2e7ed6d78937ab32935ef214
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5519
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
|
|
This config option is fam10 only.
Change-Id: I7f4619d2d4e7e7695a8ee691d879df2748f1c0c7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5518
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
There are 3 steps to enable the IMC fan control:
1. Enable fan control related registers on Hudson using oem_fan_control().
2. Set EcStruct.
3. Enable thermal zone using enable_imc_thermal_zone().
I have tested on Thatcher.
Change-Id: I959721b4fd8787ac0824f9f873efd4788682eedb
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/5359
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Not all boards which use the AMD Hudson southbridge have IDE. However,
the southbridge's asl included an 'ide.asl' file which had to be
present in $(mainboard_dir)/acpi.
Address this issue by removing the inclusion of 'ide.asl' from the
southbridge 'fch.asl' and remove 'ide.asl' from Hudson boards, none
of which have IDE.
If future hudosn board will come with IDE, the device can be declared
in the PCIO scope of dsdt.asl, right below the inclusion of 'fch.asl'.
Change-Id: Ie2efb7ebf8f5b527e26d7aaaeafbd3053a9a6b28
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5459
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Not all boards which use the AMD cimx/sb800 southbridge have IDE.
However, the southbridge's asl included an 'ide.asl' file which had to
be present in $(mainboard_dir)/acpi.
Address this issue by including ide.asl only in boards which have IDE,
and remove it from all other cimx/sb800 boards.
Change-Id: I57fcb4db9f85234b05ae1705ef81a576c478cee6
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5460
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Serialize methods against the construction of same (named) objects by
competing threads. See ACPICA BZ 909 for further details.
This change fixes issues that show up with the Ubuntu firmware test
suite (fwts) ACPI table sanity checker.
Change-Id: I49e3050a2a5aece6f031122b0211c056938d1a89
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5458
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
We should not be #include .c files, instead link early_serial into
romstage and provide a prototype.
Change-Id: Ia9277169ce1592e1fc72f8849f0982741daec567
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5416
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
There are 3 steps to enable the IMC fan control:
1. Enable fan control related registers on Hudson using oem_fan_control().
2. Set EcStruct.
3. Enable thermal zone using enable_imc_thermal_zone().
I have tested on Olive Hill.
Change-Id: I1748e8c92fb72a82bac0506ecdf98304a5bd8239
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/4301
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
There are 3 steps to enable the IMC fan control:
1. Enable fan control related registers on Hudson using oem_fan_control().
2. Set EcStruct.
3. Enable thermal zone using enable_imc_thermal_zone().
I have tested on Parmer.
Change-Id: Id11d5c5da30346c034d155a73749e7f4c9c980eb
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/4302
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
This call is already in console_init().
Change-Id: Ie0cb3595af514e37efac5ac5d474f52ba551bf22
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5140
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Clean up vendor code from hard coded #define if-def chain with a
pre-processor shift and subtract.
Change-Id: Ibce34ab576d7db8586a6ec8f9b2460268e0e1878
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/4811
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Based on info from commit messages (most devel/eval boards are mentioned
as such in commit message) and information from vendor sites (mostly based
on form factor).
Classification for siemens/sitemp_g1p1 is based on info by Nico Huber.
For Google boards based on info from ML posted by Aaron Durbin.
Remaining unclassified board is:
google/pit
For which very little info is available publically.
Change-Id: I12dfff4c629811a48cfc77be27bdc5081530b8f6
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4759
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
|
|
Overrides were to have names in line with wiki but names derived from the
tree are better in some cases.
Change-Id: Ic805ba9a3b9c7f926dc9ef27f8673f2c18e9af34
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4737
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Info supplied by: idwer
Change-Id: I3086e8118a721ded33c578c6c82e20642ef9d776
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4733
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
board_info.txt is a file to be used by board-status to add
some useful info to the generated table like flash chip type.
This series is autogenerated from wiki page Supported_Motherboards.
Change-Id: Ie2bda900713ef4883134477163320936c84c34f5
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4701
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This change allows Kconfig options ROM_SIZE and CBFS_SIZE to be
set with values that are not power of 2. The region programmed
as WB cacheable will include all of ROM_SIZE.
Side-effects to consider:
Memory region below flash may be tagged WRPROT cacheable. As an
example, with ROM_SIZE of 12 MB, CACHE_ROM_SIZE would be 16 MB.
Since this can overlap CAR, we add an explicit test and fail
on compile should this happen. To work around this problem, one
needs to use CACHE_ROM_SIZE_OVERRIDE in the mainboard Kconfig and
define a smaller region for WB cache.
With this change flash regions outside CBFS are also tagged WRPROT
cacheable. This covers IFD and ME and sections ChromeOS may use.
Change-Id: I5e577900ff7e91606bef6d80033caaed721ce4bf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4625
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
|
|
Place this in header so it works also when raminit_f.c and
raminit_f_dqs.c are not #included in romstage.c build.
The workaround remains to be disabled for all boards.
Change-Id: Iff0271ceb21ee1e28a1a31d6bbdb97e29d76461e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4568
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Do it just to remove MEM_TRAIN_SEQ test under mainboard/ to see all
K8 rev F boards do the same things here.
Change-Id: If75035a4ef8882c2618d434d83ba59c408593d86
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4567
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
K8 Rev F raminit code cannot be built without RAMINIT_SYSINFO,
so have the option enabled together with K8_REV_F_SUPPORT.
Also move the option under AMD K8.
Change-Id: I91fa0b4ae7e3e54fbcb4a4f91eb043956cd0fb60
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4582
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
AMD fam10 raminit cannot be built without RAMINIT_SYSINFO, this
is not a true option but copy-paste remainder from AMD K8.
Change-Id: Id8edc112f3bacebd1732304ac9ee6e77cc6263b7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4581
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This config was for AMD K8 only.
Change-Id: Ic1ce60041fef6ddee2dae0e3559fb78f088740af
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4556
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This config was for AMD K8 only.
Change-Id: I76276405b676d1dd4d5dbf8c5b94194a670ccb25
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4555
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ib3a69e3364418426438f88ba14e5cf744e2414fa
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4524
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I5f4bf9dbaf3470dc83d3e980bb6cab10801e15c1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4523
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
|
The main purpose of option rom is to supply int* handlers.
But supplying those is outside of coreboot scope and if someone needs those
they should run SeaBIOS anyway which runs the option roms wonderfully.
Running VGA oprom is kept because they're needed to init graphics.
This patch still keeps the options to include the option roms to make them
available to SeaBIOS.
Change-Id: I646334cf88094d3bf8f527779a68a07e0b4b93ec
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4545
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Kevin O'Connor <kevin@koconnor.net>
|
|
No ROMCC involved, no need to include .c files in romstage.c.
Change-Id: I8a2aaf84276f2931d0a0557ba29e359fa06e2fba
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4501
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Some files have incorrect/odd permissions,
correct them: remove unnecessary +x flags.
Change-Id: I784e6e599dfee88239f85bb58323aae9e40fb21c
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/4490
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
|
Propagated from
http://review.coreboot.org/3347
http://review.coreboot.org/3374
The cause of this issue is:
USB devices use bit 11(0x0b) of GP0_STS represents S3 wake up event,
but this bit is not clear after wake up. So OS thinks there is a
wake up signal and wake up immediately.
Both amd/olivehill and asrock/imb-a180 have been validated.
Change-Id: I7c26cb07bcd2e62bb792809b67314e5155c6adf6
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/4261
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The AML code of PTS and WAK for southbridge are in
UINT8 AlibSsdtKB[], Proc/GNB/Modules/GnbInitKB/AlibSsdtKB.h.
It was integrated into SSDT even it was called by nobody.
The source ASL was provided by AGESA for reference, but it
has been scrubbed when it was ported to Coreboot.
Without the calls, Olive Hill can not wake up if it boots Windows.
Both amd/olivehill and asrock/imb-a180 have been validated.
Change-Id: Ia7bba29904dbd6f33fdb08bf88bb499005ef561b
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/4260
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: I1bdc52efc827c331c53b97d2b96edafc518d05bf
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/4259
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
On AMD Trinity and Kabini boards errors similar to the following are
shown.
ASSERTION FAILED: file 'src/mainboard/asrock/imb-a180/agesawrapper.c',line 431
DmiTable:100123f7, AcpiPstatein: 10010129,AcpiSrat:0,AcpiSlit:0, Mce:10010de9,Cmc:10010eab,Alib:1002111c, AcpiIvrs:0 in
agesawrapper_amdinitlate agesawrapper_amdinitlate failed: 5
The reason is that on f16kb boards, the CDIT and DMI table are not
created. On f15tn boards, only the DMI table is not created.
Until the root cause is found, disable the table generation to remove
the errors.
Thanks to Wei Hu for debugging and reporting this issue on the list [1].
[1] http://www.coreboot.org/pipermail/coreboot/2013-November/076607.html
CDIT table is not created
Change-Id: I837e3c322bb5331a9b950a72397796a60642c3f3
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/4092
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
|
Besides the AGESA static settings, the settings in mainboard/buildOpt.c also
change the final configuration. We need to make sure the settings in FchParam
in resume stage are the same as they were in cold boot stage, otherwise the
board can not wake up more than once.
Tested on AMD/Olive Hill, AMD/Parmer and ASRock/imb-a180.
(USB keyboard doesn't work when board wakes up. It is not introduced by this
patch. It needs more debugging.)
Change-Id: I5a5e5502080e358ffc3577dc6a40bb762844d998
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/3932
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Change-Id: Ia0c37339aa69b92a1b518fa5e49adc4a7628ae5d
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3979
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Ubuntu's HDMI audio has noise and echo. Disable NoSnoopEnable can
resolve this issue.
I have tested on Ubuntu 13.04 with AMD Catalyst 13.4 Proprietary
Linux Display Driver[1].
[1]. http://support.amd.com/us/gpudownload/linux/Pages/radeon_linux.aspx
Change-Id: I5d2dddb1b7469d56cd64e3c1e0f4c6c6f095b4ab
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3934
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
Windows 7 cannot find HDMI audio device because of acpi setting.
I have tested on Windows 7. I can play music.
Change-Id: I90ade7e7be79f65783922333c2cbb2d3cc6557ea
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3933
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
A late for loop may reference over the current array allocation
and corrupt an unrelated global variable. As a quick fix bumb the
size of the array allocation uniformly to 6.
We missed these boards for commit 9c7d73ca because the arrays
had been renamed.
Change-Id: Iff2f2a0090d9302576bc72195d2a3f6fa37ce29a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3954
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
|
Northbridge code includes these headers, so they all need to
have the same name to allow different combinations of northbridge
and southbridge. This changes the sb900 names to match sb700 &
sb800, and points agesa/family12 and amd/torpedo to the new file
names.
Change-Id: I7a654ce9ae591a636a56177f64fb8cb953b4b04f
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Reviewed-on: http://review.coreboot.org/3825
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Clean whitespace errors that have gotten past lint-stable-003-whitespace
and gerrit review.
Change-Id: Id76fc68e9d32d1b2b672d519b75cdc80cc4f1ad9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3920
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
A late for loop may reference over the current array allocation
and corrupt an unrelated global variable. As a quick fix bumb the
size of the array allocation uniformly to 6.
Change-Id: Ib067fdf077e091d13e32cc3a8e4a0b713d19bcc2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3914
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
|
Change-Id: Ic7d793754a8b59623b49b7a88c09b5c6b6ef2cf0
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3768
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
ROMCC boards were left unmodified.
Change-Id: I3d842196b3f5b6999b6891b914036e9ffcc3cef0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3853
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The board name in that variable name is not necessary, as it is not board
dependent, that means using the file as a template for making a new
coreboot port for another motherboard the variable does not need to be
changed, and just increases the code differences between AMD Parmer,
AMD Thather and ASUS F2A85-M. So use a generic name.
The same was done for AMD Persimmon (and inherited by the LiPPERT
FrontRunner/Toucan-AF) in the following commit.
commit 5e70766f14253f53190ddd49a544460c6bc1e528
Author: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Date: Tue Feb 26 15:56:11 2013 +0100
AMD Fam14 boards: reduce unnecessary differences, 2nd attempt
Reviewed-on: http://review.coreboot.org/2529
The board name is *not* removed from the `CODEC_ENTRY` variable name as
the verb table not only depends on the codec but also on the board [1].
Having the board name in the variable name is a good indicator that the
pin configuration needs to be adapted when taking this file as a template
for a new port. If it was board independent, a default chip configuration
could be used and shared between all boards, which is unfortunately not
the case.
[1] Unfortunately I was not able to find Jens’ comment in my mail archive
and in the Gerrit Web interface. Not sure where it is, but I am sure
he made that comment.
Change-Id: I440a306cf4ff0a5b1b61d1983d70c66d129904d0
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3199
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Split the Family16 (Kabini) DSDT file into logical regions.
Olive Hill is the only mainboard and Kabini is the only NB/CPU
currently using Family16 AGESA code.
Change-Id: I9ef9a7245d14c59f664fc768d0ffa92ef5db7484
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3821
Tested-by: build bot (Jenkins)
|
|
Rearranged the Thatcher DSDT file to match the functionality found
on Parmer. As with the Parmer implementation, the Thatcher dsdt.asl
file in the mainboard directory contains only #include references to
the appropriate files.
As with Parmer, some include files have no content but are left as a
template for other platforms and as placeholders for completing the
ACPI implementation for Thatcher.
Change-Id: Ie44a32959cc547840914365e872416d4624d33df
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/3804
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
Change-Id: Idf26eb3fb541355bd9553c1897f647738c347eb5
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3819
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Change-Id: I7f6f6ff444fda4bdf233db1383919772afe6b635
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3815
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
Olive Hill does not have a Super I/O or keyboard controller.
Change-Id: I8c1e5d8c20c4a964fe8d98df920b416382a26d9d
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3848
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
The VBIOS device ID is set by processor family using the
map_oprom_vendev() function in the northbridge code. There
is rarely a reason why this should be overridden by the mainboard.
Since Kabini includes a default VBIOS vendor/device ID in the
northbridge Kconfig code, remove the setting from the Olive Hill
mainboard settings.
Change-Id: Icd69155f5b51105d564dd82c89e4bb54a6118a82
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3816
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ifc180e6fcd594dbedc2512ea5bef283a3ad689d3
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3814
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
