| Age | Commit message (Collapse) | Author |
|---|
|
Dumping these EHCI host controller registers is useful to
solve problems with debug devices.
Change-Id: I0610cecca57b1b952d4f87211dd00c8c0bc398b9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3866
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change Setup Stage of control messages to have no retries, while data
and status stages may retry until timing out after 1000 retries.
The correct amount of retries might vary by endpoint and device dongle
used, so make it a variable.
Change-Id: I63313f994d0bd3444a3aab527ca942da5de9e6fa
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3882
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Transaction consistently completes with 80 to 150 status reads on my
setups. Hardware should always be able to complete this within 125us
as the debug port is serviced at the beginning of each microframe.
Timeout is set to DBGP_MICROFRAME_TIMEOUT_LOOPS=1000 status reads. Do not
retry transactions if this timeout is reached as the host controller
probably needs full re-initialisation to recover.
If this timeout is not reached, but a transaction is corrupted
on the wire, or it is otherwise not properly delivered to the USB device,
transaction is retried upto DBGP_MICROFRAME_RETRIES=10 times.
Change-Id: I44bc0a1bd194cdb5a2c13d5b81fc39bc568ae054
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3881
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
It wasn't even hooked up to the build system anymore.
Change-Id: I4b962ffd945b39451e19da3ec2f7b8e0eecf2e53
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3892
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Add support for control messages with a write of data stage.
Add status stage after a read of non-zero length data stage.
Do not retry control message if device responds with STALL.
Change-Id: I16fb9ae39630b975af5461b63d050b9adaccef0f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3867
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
USB defines a mechanism to detect certain cases of lost handshakes
using an alternating data sequence number, referred to as data
toggling. This patch fixes each pipe to have its own tracking of
the data toggle state.
Change-Id: I62420bdaeadd0842da3189428a37eeb10c646900
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3865
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Add allocation for endpoint0 as a pipe for control messages.
Endpoint number was already stored in the pipe object, place devnum
there too, although all pipes will use same devnum==127.
Change-Id: I299d139bdd8083af8b04a694e8e41435ec026a25
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3864
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Nowadays, chipsets or boards do not only have one USB port with the
capabilities of a debug port but several ones. Some of these ports are
easier accessible than others, so making them configurable is also necessary.
This change adds infrastructure to switch between EHCI controllers,
but does not implement it for any chipset.
Change-Id: I079643870104fbc64091a54e1bfd56ad24422c9f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3438
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
On AMD platforms, setting of USBDEBUG_DEFAULT_PORT=0 tries to scan
all physical ports one after other in incrementing order. To avoid
possible problems with other USB devices, one can select the port
number here and bypass the scan.
Intel platforms can communicate with usbdebug dongle on one
physical port only, and this option makes no difference there.
Change-Id: I45be6cc3aa91b74650eda2d444c9fcad39d58897
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3872
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
After an USB device sees USB bus reset on the bus, it will reset to
device number 0. Per the EHCI debug port specification, a debug
dongle device may reset to the fixed debug device number of 127 instead.
Thus there is no need to try device numbers from 1 to 126.
Do a sanity-check on a returned debug descriptor as I experienced
some USB flash memory to respond on this request with zero-fill data.
Change-Id: I78d58f3dc049cd8c20c6e2aa3a4207ad7e6a6d33
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3861
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Resetting an EHCI controller when it is not halted can have
undefined behaviour. This mostly fixes a case where calling
usbdebug_init() twice would fail to reset the USB dongle device
properly.
On amd/persimmon it still requires one extra retry, but at least it
is now possible to have usbdebug enabled for both romstage and
ramstage.
Change-Id: Ib0e6e5a0167404f68af2edf112306fdb8def0be9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3862
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Letting SMI handler touch EHCI controller is an excellent source
of USB problems. Remove usbdebug entirely from SMM.
It may be possible to make usbdebug console work from SMM
after hard work and coordination with payloads and even
OS drivers. But we are not there.
Change-Id: Id50586758ee06e8d76e682dc6f64f756ab5b79f5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3858
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
This quirk is needed with a DIY debug dongle using obsolete
CY7C68013 (aka FX2) USB chips. Old revision of chip requires a
SET_CONFIGURATION to be sent, while this is not required in EHCI
debug port specs.
Change-Id: I4926eb19b7e991d6efeef782682756571ad006b9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3386
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
When we create low-level debugging of EHCI controller registers,
we call printk() within printk(). In ramstage this would leave us
with deadlock waiting on the console spinlock.
Change-Id: Idbe029af9af76de27094bb2964c60d9ccfdd96e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3860
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Increase existing level from DEBUG to INFO.
Change-Id: Ic5934aec449f921af96dd3a6524f7275f8de1304
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3859
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
If ramstage is not compressed, the CBFS module in romstage doesn't
need to support LZMA. Removing the LZMA module in this case can save
about 3000 bytes in romstage.
Change-Id: Id6f7869e32979080e2985c07029edcb39eee9106
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3878
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
For reasons explained in a previous CL, it might be necessary to "load" a file
from CBFS in place. The loading code in CBFS was, however, zeroing the area of
memory the stage was about to be loaded into. When the CBFS data is located
elsewhere this works fine, but when it isn't you end up clobbering the data
you're trying to load. Also, there's no reason to zero memory we're about to
load something into or have just loaded something into. This change makes it
so that we only zero out the portion of the memory between what was
loaded/decompressed and the final size of the stage in memory.
Change-Id: If34df16bd74b2969583e11ef6a26eb4065842f57
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3579
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Instead of returning 0 on success and -1 on error, return the decompressed
size of the data on success and 0 on error. The decompressed size is useful
information to have that was being thrown away in that function.
Change-Id: If787201aa61456b1e47feaf3a0071c753fa299a3
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3578
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Add option to log changes in USB 2.0 EHCI debug port connection.
For romstage move usbdebug as the last initialised console so one
actually can see these messages.
Init order of consoles in ramstage is undetermined and unchanged.
Change-Id: I3aceec8a93064bd952886839569e9f5beb6c5720
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3387
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
The tests for __PRE_RAM__ or __SMM__ were repeatedly used
for detection if dev->ops in the devicetree are not available
and simple device model functions need be used.
If a source file build for ramstage had __PRE_RAM__ inserted
at the beginning, the struct device would no longer match the
allocation the object had taken. This problem is fixed by
replacing such cases with explicit __SIMPLE_DEVICE__.
Change-Id: Ib74c9b2d8753e6e37e1a23fcfaa2f3657790d4c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3555
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: I74d28c13e6597c56e3b85ccd2b83386b86c200f0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3828
Tested-by: build bot (Jenkins)
|
|
Refactor the structure to better support receive and another
set of endpoints over usbdebug.
Change-Id: Ib0f76afdf4e638363ff30c67010920142c58f250
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3726
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
It might be the case that a file is being loaded from a portion of CBFS which
has already been loaded into a limitted bit of memory somewhere, and we want
to load that file in place, effectively, so that it's original location in
CBFS overlaps with its new location. That's only guaranteed to work if you use
memmove instead of memcpy.
Change-Id: Id550138c875907749fff05f330fcd2fb5f9ed924
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3577
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I4b6a57e7d8e7e685c609b1d85368585b9dd197dc
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3761
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I9cad64796fcfb7a50d9ed9ec95c56ab855c872e3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3766
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
With EARLY_CBMEM_INIT and CAR_MIGRATION selected, cbmemc_reinit()
was called twice during romstage. This effectively deleted output
of romstage in CBMEM console.
Change-Id: I21072a319c0e4a5f695b0573bc017bf7921fc663
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3609
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Store EHCI Debug Port runtime variables in CAR_GLOBAL.
For platforms without CAR_MIGRATION, logging on EHCI Debug Port is
temporarily lost when CAR is torn down at end of romstage.
On model_2065x and model_206ax ehci_debug_info was overlapping the MRC
variable region and additionally migration used incorrect size for
the structure.
Change-Id: I5e6c613b8a4b1dda43d5b69bd437753108760fca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3475
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
There are other uses for EHCI debug port besides console, so move
EHCI relocation code from console to lib.
Change-Id: I95cddd31be529351d9ec68f14782cc3cbe08c617
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3626
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Move ehci_debug_info allocation from console to lib, as console code
was only built for ramstage.
Implement dbgp_ehci_info() to return the EHCI context. Alread alias this
as dbgp_console_input() and _output() to return the console stream context
later on.
Change-Id: Id6cc07d62953f0466df61eeb159e22b0e3287d4e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3625
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Output to usbdebug console needs to be disabled until hardware is
initialized and while EHCI BAR is relocated. Add separate field
ehci_info to point to back to EHCI context when hardware is ready
to transfer data.
Change-Id: If7d441b561819ab8ae23ed9f3f320f7742ed231e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3624
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
This stuff is not used, so let's drop it.
Change-Id: I671a5e87855b4c59622cafacdefe466ab3d70143
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3660
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I999987af9cb44906e3c3135c0351a0cd6eb210ff
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/3756
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
... and drop the wrapper on ARMv7
Change-Id: If3ffe953cee9e61d4dcbb38f4e5e2ca74b628ccc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3639
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We've got enough of a handle on this to realize some things:
drm_dp_helper.h is by design device and architecture independent
i915.h is common to most intel graphics chipsets going back several years
i915_reg.h is as well
Move these files to src/include/device, and adjust the .c files accordingly.
Change-Id: I07512b3695fea0b22949074b467986420783d62a
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3637
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add three functions to edid.c:
void set_vbe_mode_info_valid(struct edid *edid, uintptr_t fb_addr)
takes an edid and uintptr_t, and fills in a static lb_framebuffer struct
as well as setting the static vbe_valid to 1 unless some problem
is found in the edid. The intent here is that this could be called from
the native graphics setup code on both ARM and x86.
int vbe_mode_info_valid(void)
returns value of the static vbe_valid.
void fill_lb_framebuffer(struct lb_framebuffer *framebuffer)
copies the static edid_fb to lb_framebuffer.
There is now a common vbe.h in src/include, removed the two special ones.
In general, graphics in coreboot is a mess, but graphics is always a
mess. We don't have a clean way to try two different ways to turn on
a device and use the one that works. One battle at a time. Overall,
things are much better.
The best part: this code would also work for ARM, which also uses EDID.
Change-Id: Id23eb61498b331d44ab064b8fb4cb10f07cff7f3
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3636
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The IOMMU AGESA needs a reserved scratch space and it wants
to allocate the stuff for runtime. So provide a simple
allocator for 4 KB CBMEM page.
Change-Id: I53bdfcd2cd69f84fbfbc6edea53a051f516c05cc
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/3315
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
src/lib/cbmem.c is for the static cbmem.
Thanks to adurbin for the Makefile.inc pointer and code on #coreboot IRC channel on freenode:
<adurbin> no. if you have CONFIG_DYNAMIC_CBMEM then cbmem.c shouldn't be compiled
[...]
<adurbin> +ifeq ($(CONFIG_EARLY_CBMEM_INIT),y)
<adurbin> +ifneq ($(CONFIG_DYNAMIC_CBMEM),y) romstage-$(CONFIG_EARLY_CBMEM_INIT) += cbmem.c
<adurbin> +endif
<adurbin> +endif
Without that fix we have:
src/lib/cbmem.c:58:43: error: no previous prototype for 'get_cbmem_toc' [-Werror=missing-prototypes]
src/lib/cbmem.c:76:6: error: no previous prototype for 'cbmem_init' [-Werror=missing-prototypes]
src/lib/cbmem.c:107:5: error: no previous prototype for 'cbmem_reinit' [-Werror=missing-prototypes]
This commit was tested on qemu-i440fx with the following commit:
qemu-i440fx: Make it compile with CONFIG_DYNAMIC_CBMEM
( http://review.coreboot.org/#/c/3504/ ).
Change-Id: I98636aad4bb4b954f3ed3957df67c77f3615964a
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3503
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I2e3fd58404c48e863a3a1b255337fb397086651b
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3506
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
src/lib/edid.c:1177: error: ‘y’ may be used uninitialized in this function
Warning is bogus, but seems my gcc (4.4.7 as shipped by RHEL-6)
isn't clever enougth to figure this on its own. So help a bit
by explicitly initializing the variable.
Change-Id: Ia9f966c9c0a6bd92a9f41f1a4a3c8e49f258be37
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3501
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add comment how one can debug the usbdebug hardware init.
Do not send printk's to usbdebug console when one is debugging
the usbdebug console initialisation itself.
Change-Id: I21a285cb31cf64e853bc626f8b6a617bc5a8be19
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3382
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
In some cases, we want a ram_check that does not die and does not
clobber the terminal with useless output that slows us down a lot.
Usage examples include Checking if the RAM is up at the start of
raminit, or checking if each rank is accessible as it is being
initialized.
As with all other ram_checks, this is more of a "Is my DRAM properly
configured?" test, which is exactly what we want for something to use
during memory initialization.
Change-Id: I95d8d9a2ce1e29c74ef97b90aba0773f88ae832c
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/3416
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Allow for automatic cache-as-ram migration for the cbmem
console. The code was refactored in the thought of making
it easier to read. The #ifdefs still exist, but they are no
longer sprinkled throughout the code. The cbmem_console_p
variable now exists globally in both romstage and ramstage.
However, the cbmem_console_p is referenced using the
cache-as-ram API. When cbmem is initialized the console
is automatically copied over by calling cbmemc_reinit()
through a callback.
Change-Id: I9f4a64e33c58b8b7318db27942e37c13804e6f2c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3235
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
There are some boards that do a significant amount of
work after cache-as-ram is torn down but before ramstage
is loaded. For example, using vboot to verify the ramstage
is one such operation. However, there are pieces of code
that are executed that reference global variables that
are linked in the cache-as-ram region. If those variables
are referenced after cache-as-ram is torn down then the
values observed will most likely be incorrect.
Therefore provide a Kconfig option to select cache-as-ram
migration to memory using cbmem. This option is named
CAR_MIGRATION. When enabled, the address of cache-as-ram
variables may be obtained dynamically. Additionally,
when cache-as-ram migration occurs the cache-as-ram
data region for global variables is copied into cbmem.
There are also automatic callbacks for other modules
to perform their own migration, if necessary.
Change-Id: I2e77219647c2bd2b1aa845b262be3b2543f1fcb7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3232
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The cooperative multitasking support allows the boot state machine
to be ran cooperatively with other threads of work. The main thread
still continues to run the boot state machine
(src/lib/hardwaremain.c). All callbacks from the state machine are
still ran synchronously from within the main thread's context.
Without any other code added the only change to the boot sequence
when cooperative multitasking is enabled is the queueing of an idlle
thread. The idle thread is responsible for ensuring progress is made
by calling timer callbacks.
The main thread can yield to any other threads in the system. That
means that anyone that spins up a thread must ensure no shared
resources are used from 2 or more execution contexts. The support
is originally intentioned to allow for long work itesm with busy
loops to occur in parallel during a boot.
Note that the intention on when to yield a thread will be on
calls to udelay().
Change-Id: Ia4d67a38665b12ce2643474843a93babd8a40c77
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3206
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
it has been unused since 9 years or so, hence drop it.
Change-Id: I0706feb7b3f2ada8ecb92176a94f6a8df53eaaa1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3212
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The cbfs core code would print out the name of the file it is
searching for and when it is found would print out the name
again. This contributes to a lot of unnecessary messages in a
functioning payload’s output. Change this message to a DEBUG one
so that it will only be printed when CONFIG_DEBUG_CBFS is enabled.
Change-Id: Ib238ff174bedba8eaaad8d1d452721fcac339b1a
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3208
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Internally there were states that had an attribute to
indicate that the timers needed to be drained. Now that
there is a way to block state transitions rely on this
ability instead of draining timers. The timers will
drain themselves when a state is blocked.
Change-Id: I59be9a71b2fd5a17310854d2f91c2a8957aafc28
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3205
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In order to properly sequence the boot state machine it's
important that outside code can block the transition from
one state to the next. When timers are not involved there's
no reason for any of the existing code to block a state
transition. However, if there is a timer callback that needs to
complete by a certain point in the boot sequence it is necessary
to place a block for the given state.
To that end, 4 new functions are added to provide the API for
blocking a state.
1. boot_state_block(boot_state_t state, boot_state_sequence_t seq);
2. boot_state_unblock(boot_state_t state, boot_state_sequence_t seq);
3. boot_state_current_block(void);
4. boot_state_current_unblock(void);
Change-Id: Ieb37050ff652fd85a6b1e0e2f81a1a2807bab8e0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3204
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The cbfs core code would print out all unmatched file
names when searching for a file. This contributes to a lot
of unnecessary messages in the boot log. Change this
message to a DEBUG one so that it will only be printed when
CONFIG_DEBUG_CBFS is enabled.
Change-Id: I1e46a4b21d80e5d2f9b511a163def7f5d4e0fb99
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3131
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Tested-by: build bot (Jenkins)
|
|
When TIMER_QUEUE is configured on call the timer callbacks on
entry into a state but before its entry callbacks. In addition
provide a barrier to the following states so that timers are drained
before proceeding. This allows for blocking state traversal for key
components of boot.
BS_OS_RESUME
BS_WRITE_TABLES
BS_PAYLOAD_LOAD
BS_PAYLOAD_BOOT
Future functionality consists of evaluating the timer callbacks within
the device tree. One example is dev_initialize() as that seems state
seems to take 90% of the boot time. The timer callbacks could then be
ran in a more granular manner.
Change-Id: Idb549ea17c5ec38eb57b4f6f366a1c2183f4a6dd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3159
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
A timer queue provides the mechanism for calling functions
in the future by way of a callback. It utilizes the MONOTONIC_TIMER
to track time through the boot. The implementation is a min-heap
for keeping track of the next-to-expire callback.
Change-Id: Ia56bab8444cd6177b051752342f53b53d5f6afc1
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3158
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
When the MONOTONIC_TIMER is available track the entry, run, and exit
times for each state. It should be noted that the times for states that
vector to OS or a payload do not have their times reported.
Change-Id: I6af23fe011609e0b1e019f35ee40f1fbebd59c9d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3156
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The notion of loading a payload in the current boot state
machine isn't actually loading the payload. The reason is
that cbfs is just walked to find the payload. The actual
loading and booting were occuring in selfboot(). Change this
balance so that loading occurs in one function and actual
booting happens in another. This allows for ample opportunity
to delay work until just before booting.
Change-Id: Ic91ed6050fc5d8bb90c8c33a44eea3b1ec84e32d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3139
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On x86 systems there is a concept of cachings the ROM. However,
the typical policy is that the boot cpu is the only one with
it enabled. In order to ensure the MTRRs are the same across cores
the rom cache needs to be disabled prior to OS resume or boot handoff.
Therefore, utilize the boot state callbacks to schedule the disabling
of the ROM cache at the ramstage exit points.
Change-Id: I4da5886d9f1cf4c6af2f09bb909f0d0f0faa4e62
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3138
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The cbmem_post_handling() function was implemented by 2
chipsets in order to save memory configuration in flash. Convert
both of these chipsets to use the boot state machine callbacks
to perform the saving of the memory configuration.
Change-Id: I697e5c946281b85a71d8533437802d7913135af3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3137
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There were previously 2 functions, init_cbmem_pre_device() and
init_cbmem_post_device(), where the 2 cbmem implementations
implemented one or the other. These 2 functions are no longer
needed to be called in the boot flow once the boot state callbacks
are utilized.
Change-Id: Ida71f1187bdcc640ae600705ddb3517e1410a80d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3136
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Utilize the static boot state callback scheduling to initialize
and tear down the coverage infrastructure at the appropriate points.
The coverage initialization is performed at BS_PRE_DEVICE which is the
earliest point a callback can be called. The tear down occurs at the
2 exit points of ramstage: OS resume and payload boot.
Change-Id: Ie5ee51268e1f473f98fa517710a266e38dc01b6d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3135
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
It's helpful to provide a distinct state that affirmatively
describes that OS resume will occur. The previous code included
the check and the actual resuming in one function. Because of this
grouping one had to annotate the innards of the ACPI resume
path to perform specific actions before OS resume. By providing
a distinct state in the boot state machine the necessary actions
can be scheduled accordingly without modifying the ACPI code.
Change-Id: I8b00aacaf820cbfbb21cb851c422a143371878bd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3134
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Many of the boot state callbacks can be scheduled at compile time.
Therefore, provide a way for a compilation unit to inform the
boot state machine when its callbacks should be called. Each C
module can export the callbacks and their scheduling requirements
without changing the shared boot flow code.
Change-Id: Ibc4cea4bd5ad45b2149c2d4aa91cbea652ed93ed
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3133
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The boot flow currently has a fixed ordering. The ordering
is dictated by the device tree and on x86 the PCI device ordering
for when actions are performed. Many of the new machines and
configurations have dependencies that do not follow the device
ordering.
In order to be more flexible the concept of a boot state machine
is introduced. At the boundaries (entry and exit) of each state there
is opportunity to run callbacks. This ability allows one to schedule
actions to be performed without adding board-specific code to
the shared boot flow.
Change-Id: I757f406c97445f6d9b69c003bb9610b16b132aa6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3132
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
While debugging a crash it was discovered that ld was inserting
address space for sections that were empty depending on section
address boundaries. This led to the assumption breaking down that
on-disk payload (code/data bits) was contiguous with the address
space. When that assumption breaks down relocation updates change
the wrong memory. Fix this by making the rmodule.ld linker script
put all code/data bits into a payload section.
Change-Id: Ib5df7941bbd64662090136e49d15a570a1c3e041
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3149
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
Because pointers can be 32bit or 64bit big,
using them in the coreboot table requires the
OS and the firmware to operate in the same mode
which is not always the case. Hence, use 64bit
for all pointers stored in the coreboot table.
Guess we'll have to fix this up once we port to
the first 128bit machines.
Change-Id: I46fc1dad530e5230986f7aa5740595428ede4f93
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3115
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: Ie497e4c8da05001ffe67c4a541bd24aa859ac0e2
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/2987
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
read_option was unified between ramstage and romstage a while ago.
However, it seems some invocations were not fixed accordingly.
This patch switches uart8250mem.c to use the new scheme.
Change-Id: I03cef4f6ee9188a6412c61d7ed34fbaff808a32b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3033
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
With CONFIG_DEBUG_COVERAGE enabled, the build currently fails with
src/lib/gcov-glue.c: In function 'fseek':
src/lib/gcov-glue.c:87:2: error: format '%d' expects argument of type 'int', but argument 4 has type 'long int' [-Werror=format]
src/lib/gcov-glue.c:87:2: error: format '%d' expects argument of type 'int', but argument 4 has type 'long int' [-Werror=format]
Change-Id: Iddaa601748c210d9dad06ae9dab2a3deaa635b2c
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3032
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The ACPI NVS region was setup in place and there was a CBMEM
table that pointed to it. In order to be able to use NVS
earlier the CBMEM region is allocated for NVS itself during
the LPC device init and the ACPI tables point to it in CBMEM.
The current cbmem region is renamed to ACPI_GNVS_PTR to
indicate that it is really a pointer to the GNVS and does
not actually contain the GNVS.
Change-Id: I31ace432411c7f825d86ca75c63dd79cd658e891
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2970
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On certain architectures such as x86 the bootstrap processor
does most of the work. When CACHE_ROM is employed it's appropriate
to ensure that the caching enablement of the ROM is disabled so that
the caching settings are symmetric before booting the payload or OS.
Tested this on an x86 machine that turned on ROM caching. Linux did not
complain about asymmetric MTRR settings nor did the ROM show up as
cached in the MTRR settings.
Change-Id: Ia32ff9fdb1608667a0e9a5f23b9c8af27d589047
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2980
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Two convenience functions are added to operate on a range_entry:
- range_entry_update_tag() - update the entry's tag
- memranges_next_entry() - get the next entry after the one provide
These functions will be used by a follow on patch to the MTRR code
to allow hole punching in WB region when the default MTRR type is
UC.
Change-Id: I3c2be19c8ea1bbbdf7736c867e4a2aa82df2d611
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2924
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Downstream payloads may need to take advantage of caching the
ROM for performance reasons. Add the ability to communicate the
variable range MTRR index to use to perform the caching enablement.
An example usage implementation would be to obtain the variable MTRR
index that covers the ROM from the coreboot tables. Then one would
disable caching and change the MTRR type from uncacheable to
write-protect and enable caching. The opposite sequence is required
to tearn down the caching.
Change-Id: I4d486cfb986629247ab2da7818486973c6720ef5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2919
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The memrange infrastructure allows for keeping track of the
machine's physical address space. Each memory_range entry in
a memory_ranges structure can be tagged with an arbitrary value.
It supports merging and deleting ranges as well as filling in
holes in the address space with a particular tag.
The memrange infrastructure will serve as a shared implementation
for address tracking by the MTRR and coreboot mem table code.
Change-Id: Id5bea9d2a419114fca55c59af0fdca063551110e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2888
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Use the memrange library for keeping track of the address
space region types. The memrange library is built to do just
that for both the MTRR code and the coreboot memtable code.
Change-Id: Iee2a7c37a3f4cf388db87ce40b580f274384ff3c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2917
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This reverts commit 56075eaefcd7ef51464206166b24a0a47a59147f
Change-Id: I8a37ce1f5ce36e4a120941ec264140abc9447ff5
Reviewed-on: http://review.coreboot.org/2915
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Use the memrange library for keeping track of the address
space region types. The memrange library is built to do just
that for both the MTRR code and the coreboot memtable code.
Change-Id: Ic667df444586c2b5b5f2ee531370bb790d683a42
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2896
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
There are assumptions that COLLECT_TIMESTAMPS and CONSOLE_CBMEM
rely on EARLY_CBMEM_INIT. This isn't true in the face of
DYNAMIC_CBMEM as it provides the same properties as EARLY_CBMEM_INIT.
Therefore, allow one to select COLLECT_TIMESTAMPS and CONSOLE_CBMEM
when DYNAMIC_CBMEM is selected. Lastly, don't hard code the cbmem
implementation when COLLECT_TIMESTAMPS is selected.
Change-Id: I053ebb385ad54a90a202da9d70b9d87ecc963656
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2895
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The x86 linker script added a .textfirst section. In
order to properly link ramstage as a relocatable module
the .textfirst section needs to be included.
Also, the support for code coverage was added by including
the constructor section and symbols. Coverage has not been
tested as I suspect it might not work in a relocatable
environment without some tweaking. However, the section
and symbols are there if needed.
Change-Id: Ie1f6d987d6eb657ed4aa3a8918b2449dafaf9463
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2883
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
There were some cbfs calls that did not get transitioned
to the new cbfs API. Fix the callsites to conform to the
actual cbfs, thus fixing the copilation errors.
Change-Id: Ia9fe2c4efa32de50982e21bd01457ac218808bd3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2880
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
coreboot tables are, unlike general system tables, a platform
independent concept. Hence, use the same code for coreboot table
generation on all platforms. lib/coreboot_tables.c is based
on the x86 version of the file, because some important fixes
were missed on the ARMv7 version lately.
Change-Id: Icc38baf609f10536a320d21ac64408bef44bb77d
Signed-off-by: Stefan Reinauer <reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/2863
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
|
|
This patch implements support for vboot firmware selection. The vboot
support is comprised of the following pieces:
1. vboot_loader.c - this file contains the entry point,
vboot_verify_firmware(), for romstage to call in order to perform
vboot selection. The loader sets up all the data for the wrapper
to use.
2. vboot_wrapper.c - this file contains the implementation calling the vboot
API. It calls VbInit() and VbSelectFirmware() with the data supplied
by the loader.
The vboot wrapper is compiled and linked as an rmodule and placed in
cbfs as 'fallback/vboot'. It's loaded into memory and relocated just
like the way ramstage would be. After being loaded the loader calls into
wrapper. When the wrapper sees that a given piece of firmware has been
selected it parses firmware component information for a predetermined
number of components.
Vboot result information is passed to downstream users by way of the
vboot_handoff structure. This structure lives in cbmem and contains
the shared data, selected firmware, VbInitParams, and parsed firwmare
components.
During ramstage there are only 2 changes:
1. Copy the shared vboot data from vboot_handoff to the chromeos acpi
table.
2. If a firmware selection was made in romstage the boot loader
component is used for the payload.
Noteable Information:
- no vboot path for S3.
- assumes that all RW firmware contains a book keeping header for the
components that comprise the signed firmware area.
- As sanity check there is a limit to the number of firmware components
contained in a signed firmware area. That's so that an errant value
doesn't cause the size calculation to erroneously read memory it
shouldn't.
- RO normal path isn't supported. It's assumed that firmware will always
load the verified RW on all boots but recovery.
- If vboot requests memory to be cleared it is assumed that the boot
loader will take care of that by looking at the out flags in
VbInitParams.
Built and booted. Noted firmware select worked on an image with
RW firmware support. Also checked that recovery mode worked as well
by choosing the RO path.
Change-Id: I45de725c44ee5b766f866692a20881c42ee11fa8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2854
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The vboot firmware selection from romstage will need to
pass the resulting vboot data to other consumers. This will
be done using a cbmem entry.
Change-Id: I497caba53f9f3944513382f3929d21b04bf3ba9e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2851
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Dynamic cbmem is now a requirement for relocatable ramstage.
This patch replaces the reserve_* fields in the romstage_handoff
structure by using the dynamic cbmem library.
The haswell code is not moved over in this commit, but it should be
safe because there is a hard requirement for DYNAMIC_CBMEM when using
a reloctable ramstage.
Change-Id: I59ab4552c3ae8c2c3982df458cd81a4a9b712cc2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2849
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Here's the great news: From now on you don't have to worry about
hitting the right io.h include anymore. Just forget about romcc_io.h
and use io.h instead. This cleanup has a number of advantages, like
you don't have to guard device/ includes for SMM and pre RAM
anymore. This allows to get rid of a number of ifdefs and will
generally make the code more readable and understandable.
Potentially in the future some of the code in the io.h __PRE_RAM__
path should move to device.h or other device/ includes instead,
but that's another incremental change.
Change-Id: I356f06110e2e355e9a5b4b08c132591f36fec7d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This patch fixes an issue for rmodules which are copied into memory
at the final load/link location. If the bss section is cleared for
that rmodule the relocation could not take place properly since the
relocation information was wiped by act of clearing the bss. The
reason is that the relocation information resides at the same
address as the bss section. Correct this issue by performing the
relocation before clearing the bss.
Change-Id: I01a124a8201321a9eaf6144c743fa818c0f004b4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2822
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This patch adds a parallel implementation of cbmem that supports
dynamic sizing. The original implementation relied on reserving
a fixed-size block of memory for adding cbmem entries. In order to
allow for more flexibility for adding cbmem allocations the dynamic
cbmem infrastructure was developed as an alternative to the fixed block
approach. Also, the amount of memory to reserve for cbmem allocations
does not need to be known prior to the first allocation.
The dynamic cbmem code implements the same API as the existing cbmem
code except for cbmem_init() and cbmem_reinit(). The add and find
routines behave the same way. The dynamic cbmem infrastructure
uses a top down allocator that starts allocating from a board/chipset
defined function cbmem_top(). A root pointer lives just below
cbmem_top(). In turn that pointer points to the root block which
contains the entries for all the large alloctations. The corresponding
block for each large allocation falls just below the previous entry.
It should be noted that this implementation rounds all allocations
up to a 4096 byte granularity. Though a packing allocator could
be written for small allocations it was deemed OK to just fragment
the memory as there shouldn't be that many small allocations. The
result is less code with a tradeoff of some wasted memory.
+----------------------+ <- cbmem_top()
| +----| root pointer |
| | +----------------------+
| | | |--------+
| +--->| root block |-----+ |
| +----------------------+ | |
| | | | |
| | | | |
| | alloc N |<----+ |
| +----------------------+ |
| | | |
| | | |
\|/ | alloc N + 1 |<-------+
v +----------------------+
In addition to preserving the previous cbmem API, the dynamic
cbmem API allows for removing blocks from cbmem. This allows for
the boot process to allocate memory that can be discarded after
it's been used for performing more complex boot tasks in romstage.
In order to plumb this support in there were some issues to work
around regarding writing of coreboot tables. There were a few
assumptions to how cbmem was layed out which dictated some ifdef
guarding and other runtime checks so as not to incorrectly
tag the e820 and coreboot memory tables.
The example shown below is using dynamic cbmem infrastructure.
The reserved memory for cbmem is less than 512KiB.
coreboot memory table:
0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
1. 0000000000001000-000000000002ffff: RAM
2. 0000000000030000-000000000003ffff: RESERVED
3. 0000000000040000-000000000009ffff: RAM
4. 00000000000a0000-00000000000fffff: RESERVED
5. 0000000000100000-0000000000efffff: RAM
6. 0000000000f00000-0000000000ffffff: RESERVED
7. 0000000001000000-000000007bf80fff: RAM
8. 000000007bf81000-000000007bffffff: CONFIGURATION TABLES
9. 000000007c000000-000000007e9fffff: RESERVED
10. 00000000f0000000-00000000f3ffffff: RESERVED
11. 00000000fed10000-00000000fed19fff: RESERVED
12. 00000000fed84000-00000000fed84fff: RESERVED
13. 0000000100000000-00000001005fffff: RAM
Wrote coreboot table at: 7bf81000, 0x39c bytes, checksum f5bf
coreboot table: 948 bytes.
CBMEM ROOT 0. 7bfff000 00001000
MRC DATA 1. 7bffe000 00001000
ROMSTAGE 2. 7bffd000 00001000
TIME STAMP 3. 7bffc000 00001000
ROMSTG STCK 4. 7bff7000 00005000
CONSOLE 5. 7bfe7000 00010000
VBOOT 6. 7bfe6000 00001000
RAMSTAGE 7. 7bf98000 0004e000
GDT 8. 7bf97000 00001000
ACPI 9. 7bf8b000 0000c000
ACPI GNVS 10. 7bf8a000 00001000
SMBIOS 11. 7bf89000 00001000
COREBOOT 12. 7bf81000 00008000
And the corresponding e820 entries:
BIOS-e820: [mem 0x0000000000000000-0x0000000000000fff] type 16
BIOS-e820: [mem 0x0000000000001000-0x000000000002ffff] usable
BIOS-e820: [mem 0x0000000000030000-0x000000000003ffff] reserved
BIOS-e820: [mem 0x0000000000040000-0x000000000009ffff] usable
BIOS-e820: [mem 0x00000000000a0000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x0000000000efffff] usable
BIOS-e820: [mem 0x0000000000f00000-0x0000000000ffffff] reserved
BIOS-e820: [mem 0x0000000001000000-0x000000007bf80fff] usable
BIOS-e820: [mem 0x000000007bf81000-0x000000007bffffff] type 16
BIOS-e820: [mem 0x000000007c000000-0x000000007e9fffff] reserved
BIOS-e820: [mem 0x00000000f0000000-0x00000000f3ffffff] reserved
BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
BIOS-e820: [mem 0x00000000fed84000-0x00000000fed84fff] reserved
BIOS-e820: [mem 0x0000000100000000-0x00000001005fffff] usable
Change-Id: Ie3bca52211800a8652a77ca684140cfc9b3b9a6b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2848
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change "ERROR" to "WARNING" -- not finding the indicated file is usually
not a fatal error.
Change-Id: I0600964360ee27484c393125823e833f29aaa7e7
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/2833
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The standard string functions memcmp(), memset(), and memcpy()
are needed by most programs. The rmodules class provides a way to
build objects for the rmodules class. Those programs most likely need
the string functions. Therefore provide those standard functions to
be used by any generic rmodule program.
Change-Id: I2737633f03894d54229c7fa7250c818bf78ee4b7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2821
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Instead of hard coding the policy for how a relocated ramstage
image is saved add an interface. The interface consists of two
functions. cache_loaded_ramstage() and load_cached_ramstage()
are the functions to cache and load the relocated ramstage,
respectively. There are default implementations which cache and
load the relocated ramstage just below where the ramstage runs.
Change-Id: I4346e873d8543e7eee4c1cd484847d846f297bb0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2805
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Accessing the flash part where the ramstage resides can be slow
when loading it. In order to save time in the S3 resume path a copy
of the relocated ramstage is saved just below the location the ramstage
was loaded. Then on S3 resume the cached version of the relocated
ramstage is copied back to the loaded address.
This is achieved by saving the ramstage entry point in the
romstage_handoff structure as reserving double the amount of memory
required for ramstage. This approach saves the engineering time to make
the ramstage reentrant.
The fast path in this change will only be taken when the chipset's
romstage code properly initializes the s3_resume field in the
romstage_handoff structure. If that is never set up properly then the
fast path will never be taken.
e820 entries from Linux:
BIOS-e820: [mem 0x000000007bf21000-0x000000007bfbafff] reserved
BIOS-e820: [mem 0x000000007bfbb000-0x000000007bffffff] type 16
The type 16 is the cbmem table and the reserved section contains the two
copies of the ramstage; one has been executed already and one is
the cached relocated program.
With this change the S3 resume path on the basking ridge CRB shows
to be ~200ms to hand off to the kernel:
13 entries total:
1:95,965
2:97,191 (1,225)
3:131,755 (34,564)
4:132,890 (1,135)
8:135,165 (2,274)
9:135,840 (675)
10:135,973 (132)
30:136,016 (43)
40:136,581 (564)
50:138,280 (1,699)
60:138,381 (100)
70:204,538 (66,157)
98:204,615 (77)
Change-Id: I9c7a6d173afc758eef560e09d2aef5f90a25187a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2800
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
When CONFIG_EARLY_CBMEM_INIT is selected romstage is supposed to have
initialized cbmem. Therefore provide a weak function for the chipset
to implement named cbmem_get_table_location(). When
CONFIG_EARLY_CBMEM_INIT is selected cbmem_get_table_location() will be
called to get the cbmem location and size. After that cbmem_initialize()
is called.
Change-Id: Idc45a95f9d4b1d83eb3c6d4977f7a8c80c1ffe76
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2797
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The romstage_handoff structure can be utilized from different components
of the romstage -- some in the chipset code, some in coreboot's core
libarary. To ensure that all users handle initialization of a newly
added romstage_handoff structure properly, provide a common function to
handle structure initialization.
Change-Id: I3998c6bb228255f4fd93d27812cf749560b06e61
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2795
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This patch adds an option to build the ramstage as a reloctable binary.
It uses the rmodule library for the relocation. The main changes
consist of the following:
1. The ramstage is loaded just under the cmbem space.
2. Payloads cannot be loaded over where ramstage is loaded. If a payload
is attempted to load where the relocatable ramstage resides the load
is aborted.
3. The memory occupied by the ramstage is reserved from the OS's usage
using the romstage_handoff structure stored in cbmem. This region is
communicated to ramstage by an CBMEM_ID_ROMSTAGE_INFO entry in cbmem.
4. There is no need to reserve cbmem space for the OS controlled memory for
the resume path because the ramsage region has been reserved in #3.
5. Since no memory needs to be preserved in the wake path, the loading
and begin of execution of a elf payload is straight forward.
Change-Id: Ia66cf1be65c29fa25ca7bd9ea6c8f11d7eee05f5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2792
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Introduce a new cbmem id to indicate romstage information. Proper
coordination with ramstage and romstage can use this cbmem entity
to communicate between one another.
Change-Id: Id785f429eeff5b015188c36eb932e6a6ce122da8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2790
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
There is a need to calculate the proper placement for an rmodule
in memory. e.g. loading a compressed rmodule from flash into ram
can be an issue. Determining the placement is hard since the header
is not readable until it is decompressed so choosing the wrong location
may require a memmove() after decompression. This patch provides
a function to perform this calculation by finding region below a given
address while making an assumption on the size of the rmodule header..
Change-Id: I2703438f58ae847ed6e80b58063ff820fbcfcbc0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2788
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The cbfs stage loading routine already zeros out the full
memory region that a stage will be loaded. Therefore, it is
unnecessary to to clear the bss again after once ramstage starts.
Change-Id: Icc7021329dbf59bef948a41606f56746f21b507f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2865
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This code is taken from an EDID reader written at Red Hat.
The key function is
int decode_edid(unsigned char *edid, int size, struct edid *out)
Which takes a pointer to an EDID blob, and a size, and decodes it into
a machine-independent format in out, which may be used for driving
chipsets. The EDID blob might come for IO, or a compiled-in EDID
BLOB, or CBFS.
Also included are the changes needed to use the EDID code on Link.
Change-Id: I66b275b8ed28fd77cfa5978bdec1eeef9e9425f1
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2837
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Coreboot's ramstage defines certain sections/symbols in its fixed
static linker script. It uses these sections/symbols for locating the
drivers as well as its own program information. Add these sections
and symbols to the rmodule linker script so that ramstage can be
linked as an rmodule. These sections and symbols are a noop for other
rmodule-linked programs, but they are vital to the ramstage.
Also add a comment in coreboot_ram.ld to mirror any changes made there
to the rmodule linker script.
Change-Id: Ib9885a00e987aef0ee1ae34f1d73066e15bca9b1
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2786
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
In certain situations boot speed can be increased by providing an
alternative implementation to cbfs_load_payload(). The
ALT_CBFS_LOAD_PAYLOAD option allows for the mainboard or chipset to
provide its own implementation.
Booted baskingridge board with alternative and regular
cbfs_load_payload().
Change-Id: I547ac9881a82bacbdb3bbdf38088dfcc22fd0c2c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2782
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
By including the heap in the bss output section the size is accounted
for in a elf PT_LOAD segment. Without this change the heap wasn't being
put into a PT_LOAD segment. The result is a nop w.r.t. functionality,
but readelf and company will have proper MemSiz fields.
Change-Id: Ibfe9bb87603dcd4c5ff1c57c6af910bbba96b02b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2750
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
A rmodule is short for relocation module. Relocaiton modules are
standalone programs. These programs are linked at address 0 as a shared
object with a special linker script that maintains the relocation
entries for the object. These modules can then be embedded as a raw
binary (objcopy -O binary) to be loaded at any location desired.
Initially, the only arch support is for x86. All comments below apply to
x86 specific properties.
The intial user of this support would be for SMM handlers since those
handlers sometimes need to be located at a dynamic address (e.g. TSEG
region).
The relocation entries are currently Elf32_Rel. They are 8 bytes large,
and the entries are not necessarily in sorted order. An future
optimization would be to have a tool convert the unsorted relocations
into just sorted offsets. This would reduce the size of the blob
produced after being processed. Essentialy, 8 bytes per relocation meta
entry would reduce to 4 bytes.
Change-Id: I2236dcb66e9d2b494ce2d1ae40777c62429057ef
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2692
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This eliminates the use of do_div() in favor of using libgcc
functions.
This was tested by building and booting on Google Snow (ARMv7)
and Qemu (x86). printk()s which use division in vtxprintf() look good.
Change-Id: Icad001d84a3c05bfbf77098f3d644816280b4a4d
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2606
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
A board without HAVE_ACPI_RESUME did not build with
COLLECT_TIMESTAMPS enabled as `cbmem.c` was not built.
Change-Id: I9c8b575d445ac566a2ec533d73080bcccc3dfbca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2549
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
