| Age | Commit message (Collapse) | Author |
|---|
|
This patch ports the LZ4 decompression code that debuted in libpayload
last year to coreboot for use in CBFS stages (upgrading the base
algorithm to LZ4's dev branch to access the new in-place decompression
checks). This is especially useful for pre-RAM stages in constrained
SRAM-based systems, which previously could not be compressed due to
the size requirements of the LZMA scratchpad and bounce buffer. The
LZ4 algorithm offers a very lean decompressor function and in-place
decompression support to achieve roughly the same boot speed gains
(trading compression ratio for decompression time) with nearly no
memory overhead.
For now we only activate it for the stages that had previously not been
compressed at all on non-XIP (read: non-x86) boards. In the future we
may also consider replacing LZMA completely for certain boards, since
which algorithm wins out on boot speed depends on board-specific
parameters (architecture, processor speed, SPI transfer rate, etc.).
BRANCH=None
BUG=None
TEST=Built and booted Oak, Jerry, Nyan and Falco. Measured boot time on
Oak to be about ~20ms faster (cutting load times for affected stages
almost in half).
Change-Id: Iec256c0e6d585d1b69985461939884a54e3ab900
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/13638
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Only i386 has code to support bounce buffer. For others coreboot
would silently discard part of binary which doesn't work and is a hell to debug.
Instead just die.
Change-Id: I37ae24ea5d13aae95f9856a896700a0408747233
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13750
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
We've had a second version of ulzma() that would check the input and
output buffer sizes in libpayload for a while now. Since it's generally
never a bad idea to double-check for overruns, let's port it to coreboot
and use it where applicable. (This requires a small fix in the four byte
at a time read optimization we only have in coreboot, since it made the
stream counter hit the end a little earlier than the algorithm liked and
could trigger an assertion.)
BRANCH=None
BUG=None
TEST=Booted Oak, Jerry and Falco.
Change-Id: Id566b31dfa896ea1b991badf5a6ad9d075aef987
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/13637
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
As there can be more than one source of firmware assets this
patch generalizes the notion of locating a particular asset.
struct asset is added along with some helper functions for
working on assets as a first class citizen.
Change-Id: I2ce575d1e5259aed4c34c3dcfd438abe9db1d7b9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10264
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
A new CBFS API is introduced to allow making CBFS access
easier for providing multiple CBFS sources. That is achieved
by decoupling the cbfs source from a CBFS file. A CBFS
source is described by a descriptor. It contains the necessary
properties for walking a CBFS to locate a file. The CBFS
file is then decoupled from the CBFS descriptor in that it's
no longer needed to access the contents of the file.
All of this is accomplished using the regions infrastructure
by repsenting CBFS sources and files as region_devices. Because
region_devices can be chained together forming subregions this
allows one to decouple a CBFS source from a file. This also allows
one to provide CBFS files that came from other sources for
payload and/or stage loading.
The program loading takes advantage of those very properties
by allowing multiple sources for locating a program. Because of
this we can reduce the overhead of loading programs because
it's all done in the common code paths. Only locating the
program is per source.
Change-Id: I339b84fce95f03d1dbb63a0f54a26be5eb07f7c8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9134
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
As per discussion with lawyers[tm], it's not a good idea to
shorten the license header too much - not for legal reasons
but because there are tools that look for them, and giving
them a standard pattern simplifies things.
However, we got confirmation that we don't have to update
every file ever added to coreboot whenever the FSF gets a
new lease, but can drop the address instead.
util/kconfig is excluded because that's imported code that
we may want to synchronize every now and then.
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, *MA[, ]*02110-1301[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin Street, Suite 500, Boston, MA 02110-1335, USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 59 Temple Place[-, ]*Suite 330, Boston, MA *02111-1307[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.:Foundation, Inc.:" {} +
$ find * -type f
-a \! -name \*.patch \
-a \! -name \*_shipped \
-a \! -name LICENSE_GPL \
-a \! -name LGPL.txt \
-a \! -name COPYING \
-a \! -name DISCLAIMER \
-exec sed -i "/Foundation, Inc./ N;s:Foundation, Inc.* USA\.* *:Foundation, Inc. :;s:Foundation, Inc. $:Foundation, Inc.:" {} +
Change-Id: Icc968a5a5f3a5df8d32b940f9cdb35350654bef9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9233
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
|
|
This patch removes quite a bit of code duplication between cpu_to_le32()
and clrsetbits_le32() style macros on the different architectures. This
also syncs those macros back up to the new write32(a, v) style IO
accessor macros that are now used on ARM and ARM64.
CQ-DEPEND=CL:254862
BRANCH=none
BUG=chromium:444723
TEST=Compiled Cosmos, Daisy, Blaze, Falco, Pinky, Pit, Rambi, Ryu,
Storm and Urara. Booted on Jerry. Tried to compare binary images...
unfortunately something about the new macro notation makes the compiler
evaluate it more efficiently (not recalculating the address between the
read and the write), so this was of limited value.
Change-Id: If8ab62912c952d68a67a0f71e82b038732cd1317
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: fd43bf446581bfb84bec4f2ebb56b5de95971c3b
Original-Change-Id: I7d301b5bb5ac0db7f5ff39e3adc2b28a1f402a72
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/254866
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9838
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch creates a new mechanism to define the static memory layout
(primarily in SRAM) for a given board, superseding the brittle mass of
Kconfigs that we were using before. The core part is a memlayout.ld file
in the mainboard directory (although boards are expected to just include
the SoC default in most cases), which is the primary linker script for
all stages (though not rmodules for now). It uses preprocessor macros
from <memlayout.h> to form a different valid linker script for all
stages while looking like a declarative, boilerplate-free map of memory
addresses to the programmer. Linker asserts will automatically guarantee
that the defined regions cannot overlap. Stages are defined with a
maximum size that will be enforced by the linker. The file serves to
both define and document the memory layout, so that the documentation
cannot go missing or out of date.
The mechanism is implemented for all boards in the ARM, ARM64 and MIPS
architectures, and should be extended onto all systems using SRAM in the
future. The CAR/XIP environment on x86 has very different requirements
and the layout is generally not as static, so it will stay like it is
and be unaffected by this patch (save for aligning some symbol names for
consistency and sharing the new common ramstage linker script include).
BUG=None
TEST=Booted normally and in recovery mode, checked suspend/resume and
the CBMEM console on Falco, Blaze (both normal and vboot2), Pinky and
Pit. Compiled Ryu, Storm and Urara, manually compared the disassemblies
with ToT and looked for red flags.
Change-Id: Ifd2276417f2036cbe9c056f17e42f051bcd20e81
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f1e2028e7ebceeb2d71ff366150a37564595e614
Original-Change-Id: I005506add4e8fcdb74db6d5e6cb2d4cb1bd3cda5
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/213370
Reviewed-on: http://review.coreboot.org/9283
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Instead of having different structures for loading
ramstage and payload align to using struct prog.
This also removes arch_payload_run() in favor of
the prog_run() interface.
Change-Id: I31483096094eacc713a7433811cd69cc5621c43e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/8849
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The struct prog serves as way to consolidate program
loading. This abstraction can be used to perform more
complicated execution paths such as running a program
on a separate CPU after it has been loaded. Currently
t124 and t132 need to do that in the boot path. Follow
on patches will allow the platform to decide how to
execute a particular program.
Note: the vboot path is largely untouched because it's
already broken in the coreboot.org tree. After getting
all the necessary patches pushed then vboot will be
fixed.
Change-Id: Ic6e6fe28c5660fb41edee5fd8661eaf58222f883
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/8839
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Instead of having 2 different functions to call when a program
is loaded provide a single callback with flags parameter. The
previous callbacks for cache management routines did this:
for_each_program_segment:
arch_program_segment_loaded(start, size);
arch_program_loaded();
Now, use one callback instead:
for_each_program_segment:
arch_segment_loaded(start, size, SEG_FINAL?);
Change-Id: I3811cba92e3355d172f605e4444f053321b07a2a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/8838
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Two weak functions were added so that architecture specific operations
on each segment of payload or stage can be performed.
Each architecture must define its own operations, otherwise the
behavior will default to do-nothing functions.
This patch has been updated by to fit more in line with
how program loading is currently being done. The API is the
same as the original, but all call sites to stages/payloads
have been updated. This is known to break any archs that use
rmodule loading that needs cache maintenance. That will be fixed
in a forthcoming patch. Also, the vboot paths are left as is
for easier upstreaming of the rest of the vboot patches.
Original-Change-Id: Ie29e7f9027dd430c8b4dde9848fa3413c5dbfbfa
Original-Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/239881
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
(cherry picked from commit c82c21ce87a4c02bd9219548a4226a58e77beef0)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ifcee5cd9ac5dbca991556296eb5e170b47b77af7
Reviewed-on: http://review.coreboot.org/8837
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Instead of two headers for payload and ramstage loading
combine the 2 files into one. This also allows for easier
refactoring by keeping header files consistent.
Change-Id: I4a6dffb78ad84c78e6e96c886d361413f9b4a17d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/8708
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Eliminate duplicated printout and if needed, print only changed
information.
BUG=none
TEST=verified that the 'New segment dstaddr...' message is not
duplicated anymore
Original-Change-Id: Ia13593394fccbb225f2bd9ab2b9228bac29d50fb
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/199672
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit aadf018821ebfa63d6ac9d2429ae1fb483dd6cb3)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I7544bddc4026191395cfe3b8ac66256ec223391e
Reviewed-on: http://review.coreboot.org/7937
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Rename coreboot_ram stage to ramstage. This is done in order to provide
consistency with other stage names (bootblock, romstage) and to allow any
Makefile rule generalization, required for patches to be submitted later.
Change-Id: Ib66e43b7e17b9c48b2d099670ba7e7d857673386
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: http://review.coreboot.org/5567
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
s_srcaddr is uninitialized in the BSS section, leading to a
garbage valued operand on the LHS of a '<' on line 383.
Change-Id: Ie4fec91b09c70fb1d91ad3918ac3f60653fa1d83
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5314
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Instead of packing and unpacking entries in lb_mem use
the bootmem infrastructure for performing sanity checks
during payload loading.
Change-Id: Ica2bee7ebb0f6bf9ded31deac8cb700aa387bc7a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5303
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The selfboot() function relied on global variables
within the selfboot.c compilation unit. Now that the
bounce buffer is a part of struct payload use a new
architecture-specific arch_payload_run() function
for jumping to the payload. selfboot() can then be
removed.
Change-Id: Icec74942e94599542148561b3311ce5096ac5ea5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5300
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In order to break the dependency on selfboot for jumping to
payload the bounce buffer location needs to be communicated.
Therefore, add the bounce buffer to struct payload.
Change-Id: I9d9396e5c5bfba7a63940227ee0bdce6cba39578
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5299
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In order to encapsulate more data for self loading use struct
payload as the type. That way modifications to what is needed
for payload loading does not introduce more global variables.
Change-Id: I5b8facd7881e397ca7de1c04cec747fc1dce2d5f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5298
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The selfboot() routine was perfoming most of the common teardown
and stack checking infrastructure. Move that code into
payload_run() to prepare removal of the selfboot() function.
Change-Id: I29f2a5cfcc692f7a0fe2656cb1cda18158c49c6e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5297
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
A payload can be loaded either from a vboot region or from cbfs.
Provide a common place for choosing where the payload is loaded
from. Additionally, place the logic in the 'loaders' directory
similarly to the ramstage loader infrastructure.
Change-Id: I6b0034ea5ebd04a3d058151819ac77a126a6bfe2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5296
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
cbfs used u32 in a number of cases where uintptr_t was
correct. This change builds for both 64-bit and 32-bit
boards.
Change-Id: If42c722a8a9e8d565d3827f65ed6c2cb8e90ba60
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/4037
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
It wasn't even hooked up to the build system anymore.
Change-Id: I4b962ffd945b39451e19da3ec2f7b8e0eecf2e53
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3892
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This stuff is not used, so let's drop it.
Change-Id: I671a5e87855b4c59622cafacdefe466ab3d70143
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3660
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I999987af9cb44906e3c3135c0351a0cd6eb210ff
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/3756
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The notion of loading a payload in the current boot state
machine isn't actually loading the payload. The reason is
that cbfs is just walked to find the payload. The actual
loading and booting were occuring in selfboot(). Change this
balance so that loading occurs in one function and actual
booting happens in another. This allows for ample opportunity
to delay work until just before booting.
Change-Id: Ic91ed6050fc5d8bb90c8c33a44eea3b1ec84e32d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3139
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On x86 systems there is a concept of cachings the ROM. However,
the typical policy is that the boot cpu is the only one with
it enabled. In order to ensure the MTRRs are the same across cores
the rom cache needs to be disabled prior to OS resume or boot handoff.
Therefore, utilize the boot state callbacks to schedule the disabling
of the ROM cache at the ramstage exit points.
Change-Id: I4da5886d9f1cf4c6af2f09bb909f0d0f0faa4e62
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3138
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Utilize the static boot state callback scheduling to initialize
and tear down the coverage infrastructure at the appropriate points.
The coverage initialization is performed at BS_PRE_DEVICE which is the
earliest point a callback can be called. The tear down occurs at the
2 exit points of ramstage: OS resume and payload boot.
Change-Id: Ie5ee51268e1f473f98fa517710a266e38dc01b6d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3135
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On certain architectures such as x86 the bootstrap processor
does most of the work. When CACHE_ROM is employed it's appropriate
to ensure that the caching enablement of the ROM is disabled so that
the caching settings are symmetric before booting the payload or OS.
Tested this on an x86 machine that turned on ROM caching. Linux did not
complain about asymmetric MTRR settings nor did the ROM show up as
cached in the MTRR settings.
Change-Id: Ia32ff9fdb1608667a0e9a5f23b9c8af27d589047
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2980
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch adds an option to build the ramstage as a reloctable binary.
It uses the rmodule library for the relocation. The main changes
consist of the following:
1. The ramstage is loaded just under the cmbem space.
2. Payloads cannot be loaded over where ramstage is loaded. If a payload
is attempted to load where the relocatable ramstage resides the load
is aborted.
3. The memory occupied by the ramstage is reserved from the OS's usage
using the romstage_handoff structure stored in cbmem. This region is
communicated to ramstage by an CBMEM_ID_ROMSTAGE_INFO entry in cbmem.
4. There is no need to reserve cbmem space for the OS controlled memory for
the resume path because the ramsage region has been reserved in #3.
5. Since no memory needs to be preserved in the wake path, the loading
and begin of execution of a elf payload is straight forward.
Change-Id: Ia66cf1be65c29fa25ca7bd9ea6c8f11d7eee05f5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2792
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
In certain situations boot speed can be increased by providing an
alternative implementation to cbfs_load_payload(). The
ALT_CBFS_LOAD_PAYLOAD option allows for the mainboard or chipset to
provide its own implementation.
Booted baskingridge board with alternative and regular
cbfs_load_payload().
Change-Id: I547ac9881a82bacbdb3bbdf38088dfcc22fd0c2c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2782
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Entry point in payload segment header is a 64 bit integer (ntohll). The debug
message is currently reading that as a 32 bit integer (which will produce
00000000 for most platforms).
Change-Id: I931072bbb82c099ce7fae04f15c8a35afa02e510
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2535
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
Summary:
Isolate CBFS underlying I/O to board/arch-specific implementations as
"media stream", to allow loading and booting romstage on non-x86.
CBFS functions now all take a new "media source" parameter; use
CBFS_DEFAULT_MEDIA if you simply want to load from main firmware.
API Changes:
cbfs_find => cbfs_get_file.
cbfs_find_file => cbfs_get_file_content.
cbfs_get_file => cbfs_get_file_content with correct type.
CBFS used to work only on memory-mapped ROM (all x86). For platforms like ARM,
the ROM may come from USB, UART, or SPI -- any serial devices and not available
for memory mapping.
To support these devices (and allowing CBFS to read from multiple source
at the same time), CBFS operations are now virtual-ized into "cbfs_media". To
simplify porting existing code, every media source must support both "reading
into pre-allocated memory (read)" and "read and return an allocated buffer
(map)". For devices without native memory-mapped ROM, "cbfs_simple_buffer*"
provides simple memory mapping simulation.
Every CBFS function now takes a cbfs_media* as parameter. CBFS_DEFAULT_MEDIA
is defined for CBFS functions to automatically initialize a per-board default
media (CBFS will internally calls init_default_cbfs_media). Also revised CBFS
function names relying on memory mapped backend (ex, "cbfs_find" => actually
loads files). Now we only have two getters:
struct cbfs_file *entry = cbfs_get_file(media, name);
void *data = cbfs_get_file_content(CBFS_DEFAULT_MEDIA, name, type);
Test results:
- Verified to work on x86/qemu.
- Compiles on ARM, and follow up commit will provide working SPI driver.
Change-Id: Iac911ded25a6f2feffbf3101a81364625bb07746
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In order to provide some insight on what code is executed during
coreboot's run time and how well our test scenarios work, this
adds code coverage support to coreboot's ram stage. This should
be easily adaptable for payloads, and maybe even romstage.
See http://gcc.gnu.org/onlinedocs/gcc/Gcov.html for
more information.
To instrument coreboot, select CONFIG_COVERAGE ("Code coverage
support") in Kconfig, and recompile coreboot. coreboot will then
store its code coverage information into CBMEM, if possible.
Then, run "cbmem -CV" as root on the target system running the
instrumented coreboot binary. This will create a whole bunch of
.gcda files that contain coverage information. Tar them up, copy
them to your build system machine, and untar them. Then you can
use your favorite coverage utility (gcov, lcov, ...) to visualize
code coverage.
For a sneak peak of what will expect you, please take a look
at http://www.coreboot.org/~stepan/coreboot-coverage/
Change-Id: Ib287d8309878a1f5c4be770c38b1bc0bb3aa6ec7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2052
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
It only has two files, move them to src/lib
Change-Id: I17943db4c455aa3a934db1cf56e56e89c009679f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1959
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
