| Age | Commit message (Collapse) | Author |
|---|
|
List of changes:
1. Add new GFx ID 0x46B3 into device/pci_ids.h
2. Update new GFx ID into common graphics.c
3. Add new GFx ID description into report_platform.c
TEST=Build and boot brya
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I4343c7343875eb40c2955f6f4dd98d6446852dc0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55662
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I84c8470764a4e6e09220044966111ffe72078099
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55674
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
devfn_disable() function is used to disable a device based on
given bus, device function number. This function checks if the
device is at enable state and disables the device.
Change-Id: Ia4a8bfec7fc95c729a5bb156f88e9aab3bf5dd41
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The `pnp_unset_and_set_config` function was only available when building
with `ENV_PNP_SIMPLE_DEVICE` set. Add the complementary definition using
device pointers, for the sake of completeness.
Change-Id: I2a21e635f41f3f786057500fa96a2b3116e30d76
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Máté Kukri <kukri.mate@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Add lpddr4.c utility file with lpddr4_speed_mhz_to_reported_mts.
Fill in lpddr4_speeds using JDEC 209-4C table 210.
LPDDR4 SPD decoding utilities are not included since there isn't
a present need.
BUG=b:184124605
TEST=Build and run on guybrush
Change-Id: Id8ddfc98fff4255670c50e1ddd4d0a1326265772
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
is_devfn_enabled() function helps to check if a device
is enabled based on given device function number. This
function internally called is_dev_enabled() to check
device state.
Change-Id: I6aeba0da05b13b70155a991f69a6abf7eb48a78c
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add Alder Lake specific graphics device ID. The document# 641765 lists
the id 0x46a8.
TEST=Verify boot on brya
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I6f36256505a3e07c6197079ea2013991e841401b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55256
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update SA & IGD DIDs table as per latest EDS (Doc no: 601458).
Add extra SKUs and fix the mismatched SKU numbers accordingly.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I62fd9e6a7cf0fc6f541f3d6d9edd31d41db7279f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
With the introduction of fw_config support in coreboot, it is possible
for mainboards to control the state of a device (on/off) in ramstage
using fw_config probe conditions. However, the device tree in
immutable in all other stages and hence `is_dev_enabled()` does not
really reflect the true state as in ramstage.
This change adds a call to `fw_config_probe_dev()` in
`is_dev_enabled()` when device tree is immutable (by checking
DEVTREE_EARLY) to first check if device is disabled because of device
probe conditions. If so, then it reports device as being
disabled. Else, dev->enabled is used to report the device state.
This allows early stages (bootblock, romstage) to use
`is_dev_enabled()` to get the true state of the device by taking probe
conditions into account and eliminates the need for each caller to
perform their own separate probing.
Change-Id: Ifede6775bda245cba199d3419aebd782dc690f2c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54752
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Alder Lake specific Host and Graphics device IDs.
As per latest document number: 619501, these IDs got an update.
Change-Id: I548a903714ccc7470f1425ac67c0c66522437365
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54674
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Updated CPU ID and IGD ID for Alder Lake as per EDS.
TEST=Code compilation works and coreboot is able to boot and identify
new device Ids.
Change-Id: I2759a41a0db1eba5d159edfc89460992914fcc3c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
These global variables are not used anywhere. Drop them.
Change-Id: I3fe60b970153d913ae7b005257e2b53647d6f343
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53977
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With the recent switch to SMM module loader v2, the size of the SMM for
module google/volteer increased to above 64K in size, and thus failed to
install the permanent SMM handler. Turns out, the devicetree is all
pulled into the SMM build because of elog, which calls
`pci_dev_is_wake_source`, and is the only user of `struct device` in
SMM. Changing this function to take a pci_devfn_t instead allows the
linker to remove almost the entire devicetree from SMM (only usage left
is when disabling HECI via SMM).
BUG=b:186661594
TEST=Verify loaded program size of `smm.elf` for google/volteer is
almost ~50% smaller.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4c39e5188321c8711d6479b15065e5aaedad8f38
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Intel document 335192-004 contains the PCI device IDs for Z370 and
H310C, but lacks the ID for B365. The ID appears on some websites:
https://linux-hardware.org/index.php?id=pci:8086-a2cc-1849-a2cc
Change-Id: Iea3c435713c46854c5271fbc266f47ba4573db52
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52703
Reviewed-by: Timofey Komarov <happycorsair@yandex.ru>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Taken from Intel document 334658-003 (7th Generation Intel Processor
Family I/O for U/Y Platforms and 8th Generation Intel Processor Family
I/O for U Quad Core Platforms, Datasheet - Volume 1 of 2).
Change-Id: I1d48c8868e1e5d453d599ecec835938ce09935d0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52702
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Timofey Komarov <happycorsair@yandex.ru>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The code name for these PCHs is Union Point, abbreviated as `UPT`. There
are some 300-series Union Point PCHs (H310C, B365, Z370) which are meant
to be paired with Coffee Lake CPUs instead of Skylake or Kaby Lake CPUs,
and referring to them as `KBP` (Kaby Point, I guess) would be confusing.
Tested with BUILD_TIMELESS=1, HP 280 G2 remains identical.
Change-Id: I1a49115ae7ac37e76ce8d440910fb59926f34fac
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52700
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Timofey Komarov <happycorsair@yandex.ru>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Added new LPC and IGD device IDs for Alderlake M.
Also, added entry for CPUID_ALDERLAKE_M_A0 in report_platform.c
TEST=Check if platform information print is coming properly in coreboot
Change-Id: If33c43da8cbd786261b00742e342f0f01622c607
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50138
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These aren't used anywhere anymore.
Change-Id: I4cf2fc0d07a772886e90fba4f66591a7b0a40e6c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Drop unnecessary typedefs and rename DDR4-specific definitions to avoid
name clashes, as done for DDR3 in earlier commits. This allows including
and using both DDR3 and DDR4 headers in the same compilation unit.
Change-Id: I17f1cd88f83251ec23e9783a617f4d2ed41b07f0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51898
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To avoid name clashes with definitions for other DRAM generations,
rename the enum type and values to contain `ddr3` or `DDR3`.
Change-Id: If3710149ba94b94ed14f03e32f5e1533b4bc25c8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51896
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These typedefs are not necessary. Remove them, and rename some elements
to avoid any confusion with other DRAM generations, such as DDR4.
Change-Id: Ibe40f33372358262c540e371f7866b06a4ac842a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51895
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
I was bugged by spurious "Failed to enable LTR" messages for years.
Looking at the the current algorithm, it is flawed in multiple ways:
* It looks like the author didn't know they implemented a
recursive algorithm (pciexp_enable_ltr()) inside another
recursive algorithm (pciexp_scan_bridge()). Thus, at every
tree level, everything is run again for the whole sub-
tree.
* LTR is enabled no matter if `.set_ltr_max_latencies` is
implemented or not. Leaving the endpoints' LTR settings
at 0: They are told to always report zero tolerance.
In theory, depending on the root-complex implementation,
this may result in higher power consumption than without
LTR messages.
* `.set_ltr_max_latencies` is only considered for the direct
parent of a device. Thus, even with it implemented, an
endpoint below a (non-root) bridge may suffer from the 0
settings as described above.
* Due to the double-recursive nature, LTR is enabled starting
with the endpoints, then moving up the tree, while the PCIe
spec tells us to do it in the exact opposite order.
With the current implementation of pciexp_scan_bridge(), it is
hard to hook anything in that runs for each device from top to
bottom. So the proposed solution still adds some redundancy:
First, for every device that uses pciexp_scan_bus(), we enable
LTR if possible (see below). Then, when returning from the bus-
scanning recursion, we enable LTR for every device and configure
the maximum latencies (if supported). The latter runs again on
all bridges, because it's hard to know if pciexp_scan_bus() was
used for them.
When to enable LTR:
* For all devices that implement `.set_ltr_max_latencies`.
* For all devices below a bridge that has it enabled already.
Change-Id: I2c5b8658f1fc8cec15e8b0824464c6fc9bee7e0e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51328
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Let the linker do its job.
This fixes building with !CONFIG_PCIEXP_HOTPLUG on some platforms.
Change-Id: I46560722dcb5f1d902709e40b714ef092515b164
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Replace the existing, odd looking, unordered definitions used for
LTR configuration with the usual names used by upstream libpci.
TEST=Built google/brya0 with BUILD_TIMELESS=1: no changes.
Fixes: Code looked like UEFI copy-pasta. Header file was a mess.
Change-Id: Icf666692e22730e1bdf4bcdada433b3219af568a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51327
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename `set_L1_ss_latency` to what it does: `set_ltr_max_latencies`.
TEST=Built google/brya0 with BUILD_TIMELESS=1: no changes.
Change-Id: I7008aa18bf80d6709dce1b2d3bfbb5ea407a0574
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51326
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index.
Since all boards do pad setup on their own now, finally drop the pad
configuration from SoC common code.
Change-Id: Id03719eb8bd0414083148471ed05dea62a895126
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
|
|
According to Intel EmmitsBurg EDS, doc# 606161:
* Add PCI devid for SPI.
* Add PCI devid for ESPI (LPC).
EmmitsBurg (EBG) PCH is used in the chipset with Sapphire Rapids
Scalable Processor (SPR-SP).
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: Ie8925cb739c95c34febf9002149de437d19c8234
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Continue unifying Lynx Point and Wildcat Point (PCH for Broadwell) code.
Define the WPT-LP SMBus PCI device ID, add it to smbus.c of Lynx Point,
and drop all now-unnecessary SMBus code from Broadwell.
Change-Id: I864d7c2dd47895a3c559e2f1219425cda9fd0c17
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch adds new soundwire device ALC1308
The codec properties are filled out as best as possible
with the datasheet as a reference.
The ACPI address for the codec is calculated with the information in
the codec driver combined with the devicetree.cb hierarchy where the
link and unique IDs are extracted from the device path.
The unique ID is calculated from schematics by referring to ASEL[1:0]
strap settings. Datasheet of ALC1308 provides info about the mapping of
ASEL strap settings to unique ID
For example this device is connected to master link ID 1 and has strap
settings configuring it for unique ID 2.
chip drivers/soundwire/alc1308
register "desc" = ""Left Speaker""
device generic 1.2 on end
end
Bug=None
Test=Build and boot on TGLRVP.Extract SSDT and confirm that the entries for
PCI0.HDAS.SNDW are present for ALC1308
Test speaker out functionality
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: Ibf3f1d5c6881cbd106e96ad1ff17ca216aa272ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51042
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sathyanarayana Nujella
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Taken from document 322170-028 (5 series specification update).
Tested on out-of-tree HP ProBook 6550b (HM57), fixes several issues.
Without this patch, EHCI controllers had no IRQ assigned and there were
unexpected exceptions about NMIs. With this patch, the issues are gone.
Change-Id: Icd31dd89ba49e38a5e4c108a8361dbf636332ab8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51066
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The device function is missing in the PCI device table in the PPR, but
is present in the hardware. Verified on a Mandolin board with PCO APU.
The corresponding ticket for the PPR is DESPCSOC-6667.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie91438bc905691d443ca4e7841549d1e3bca39ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This makes it clear what this function pointer is used for.
Change-Id: I2090e164edee513e05a9409d6c7d18c2cdeb8662
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51009
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move SPD manufacturer ID decoding to device/dram. Will be used by the
following patch outside of SMBIOS scope as well.
Change-Id: Iec175cd6ab1d20761da955785e4bc0e87ae02dbb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
On some mainboards, codec configuration depends on settings that are
only known at runtime, which is impossible to specify using one verb
table. Add an optional `mainboard_azalia_program_runtime_verbs` hook
where mainboards can program runtime-dependent codec verbs.
Change-Id: I7efeba5c26051aeb5061cce191ace08c304a6c70
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
On some boards, Azalia configuration depends on config settings that are
not known at compile-time. Expose a function to program a verb table, to
be used in subsequent commits.
Change-Id: Ie9607f6e733df66f0ca26a4bb70e0864ce1d4512
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Add a driver which puts the device into power-saving mode.
BUG=b:177955523
BRANCH=zork
TEST=boot and see this message:
BayHub LV2: Power-saving enabled 110102
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Idc1340b1a6fe7063d16c8ea16488d6e2b8b308cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I372b6b2d602dfe116d5791bb6a6653454523b42b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Timofey Komarov <happycorsair@yandex.ru>
|
|
Change-Id: Ibdddb3309f862f52c578e91ba3dc310dff8f70bc
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Timofey Komarov <happycorsair@yandex.ru>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add SATA controller ID for Cannon Lake PCH-H Mobile HALO
(see document number: 571182)
Add SPDX license header
Bug=N/A
TEST=Build of Intel Coffeelake H SO-DIMM DDR4 RVP11 successfully
completed
Change-Id: Ic7e6ace2a24b4278b04caa58be907d38f4d117cd
Signed-off-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
All uses of `mmconf_resource_init` have been replaced in previous
patches with `mmconf_resource`, which uses Kconfig symbol values.
Change-Id: I4473268016ed511aa5c4930a71977e722e34162a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This is necessary because ASL Memory32Fixed values cannot contain
operations, even if they can be evaluated to constants. Add a sanity
check in pci_mmio_cfg.h to ensure consistency with MMCONF_BUS_NUMBER.
Change-Id: I8f0b5edf166580cc12c1363d8d6b6ef0f2854be9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50033
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Alder Lake M specific CPU, System AGent, PCH (Alder Point aka
ADP),
IGD device IDs.
Document Number: 619501, 626817
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: Ib13fe229f9e65eae8967aa20e28e29ac5c319265
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49629
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the definition of config_of_soc() to a macro that
expands to __pci_0_00_0_config instead of accessing the config
structure by referencing the struct device. This allows linker to
optimize out unused portions of the device tree from early stages.
With this change, bootblock .text section size drops as follows:
Platform | Size without change | Size with change | Reduction |
---------------|---------------------|------------------|-------------|
GLK (ampton) | 27112 bytes | 9832 bytes | 17280 bytes |
APL (reef) | 26488 bytes | 17528 bytes | 8960 bytes |
TGL (volteer2) | 47760 bytes | 21648 bytes | 26112 bytes |
CML (hatch) | 40616 bytes | 22792 bytes | 17824 bytes |
JSL (waddledee)| 37872 bytes | 19408 bytes | 18464 bytes |
KBL (soraka) | 31840 bytes | 21568 bytes | 10272 bytes |
As static.h is now included in device.h which gets pulled in during
the unit tests, a dummy static.h is added under tests/include.
Change-Id: I1fbf5b9817065e967e46188739978a1cc96c2c7e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
TEST=Able to build and boot ADLRVP.
Change-Id: Ia331998b46abcf10e939078dea992589f09139bd
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49301
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the register PNP_IO4, which will be used by IT5570E in CB:48894.
Change-Id: Ic820295247323f546d4c48ed17cfa4eab3dc5e92
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48924
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Introduce a new device `gpio` that is going to be used for generic
abstraction of gpio operations in the devicetree.
The general idea behind this is that every chip can have gpios that
shall be accessible in a very generic way by any driver through the
devicetree.
The chip that implements the chip-specific gpio operations has to assign
them to the generic device operations struct, which then gets assigned
to the gpio device during device probing. See CB:48583 for how this gets
done for the SoCs using intelblocks/gpio.
The gpio device then can be added to the devicetree with an alias name
like in the following example:
chip soc/whateverlake
device gpio 0 alias soc_gpio on end
...
end
Any driver that requires access to this gpio device needs to have a
device pointer (or multiple) and an option for specifying the gpio to be
used in its chip config like this:
struct drivers_ipmi_config {
...
DEVTREE_CONST struct device *gpio_dev;
u16 post_complete_gpio;
...
};
The device `soc_gpio` can then be linked to the chip driver's `gpio_dev`
above by using the syntax `use ... as ...`, which was introduced in
commit 8e1ea52:
chip drivers/ipmi
use soc_gpio as gpio_dev
register "bmc_jumper_gpio" = "GPP_D22"
...
end
The IPMI driver can then use the generic gpio operations without any
knowlege of the chip's specifics:
unsigned int gpio_val;
const struct gpio_operations *gpio_ops;
gpio_ops = dev_get_gpio_ops(conf->gpio_dev);
gpio_val = gpio_ops->get(conf->bmc_jumper_gpio);
For a full example have a look at CB:48096 and CB:48095.
This change adds the new device type to sconfig and adds generic gpio
operations to the `device_operations` struct. Also, a helper for getting
the gpio operations from a device after checking them for NULL pointers
gets added.
Successfully tested on Supermicro X11SSM-F with CB:48097, X11SSH-TF with
CB:48711 and OCP DeltaLake with CB:48672.
Change-Id: Ic4572ad8b37bd1afd2fb213b2c67fb8aec536786
Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Many uses of `azalia_set_bits` are used to toggle the reset bit. To
avoid having to repeat the register operations and the corresponding
comment, create two helpers with self-explanatory names. They will be
put to use in subsequent commits, with one change for each function.
Change-Id: If0594fdaf99319f08a2e272cd37958f0f216e654
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Allow to specify which table should the verb list be read from.
Change-Id: Id1bc40c4364cda848f416bad9eeab1b8ca3e9512
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The `dev` parameter isn't used anywhere.
Change-Id: I05643f8201137ffe89ded1e3f989c5a0f04e0af1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
To allow dropping copies of this function, make it non-static. Also,
rename it to `azalia_find_verb` as the function is now globally visible.
Finally, replace the copies in chipset code with `azalia_find_verb`.
Change-Id: Ie66323b2c62139e86d3d7e003f6653a3def7b5f2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
There's many copies of this function in the tree. Make the copy in
azalia_device.c non-static and rename it to `azalia_set_bits`, then
replace all other copies with it. Since azalia_device.c is only built
when AZALIA_PLUGIN_SUPPORT is selected, select it where necessary.
This has the side-effect of building hda_verb.c from the mainboard
directory. If this patch happens to break audio on a mainboard, it's
because its hda_verb.c was always wrong but wasn't being compiled.
Change-Id: Iff3520131ec7bc8554612969e3a2fe9cdbc9305e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Add LPC/eSPI device ID of Emmitsburg (EMB) for setting LPC resources.
Refer to Emmitsburg PCH EDS (606161).
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: Ie5a5d9ba7e4f664ada2dae2294d6e4d0280a2157
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Since config_of() calls die() if dev or dev->chip_info are NULL,
config_of_soc() will either return a non-NULL pointer or won't return.
Change-Id: I6de6bb1610e823af215436c94ff1a78ff6b86b78
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Add the PCI IDs for Alderlake TCSS,
* USB xHCI
* USB xDCI
* TBT DMA
* TBT PCIe
Change-Id: I28bb310c7b031d2766c9e03dbcbe1c79901a7d87
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48242
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Device ID for "D18:F6 - GSPI #2" shoud be 0xA0FB
BUG=none
TEST=Boot to OS, verify SSDT
Signed-off-by: Selma BENSAID <selma.bensaid@intel.com>
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I0d814170d24ff1b989eceb1d9ebdf6134df85e2e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48060
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Only two definitions are actually used somewhere, the rest is unused.
Change-Id: Iec52d0d47fce6a1ec5455b670824b995a7a34a4c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47407
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Used documents:
- 328904-003
- 329003-003
Change-Id: I95790cda6f7c42a9de57bf5e92eb829ee1807dbe
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47807
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I0caea5627045b7855e2c5f3cb01d4fa21332788b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I215058bcb0d53bfec974b8d3721cb4c998fcbee5
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47702
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4499c383e63cd12a0fc11efd94ef396d9ad23789
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Different models within family 17h have different PCI IDs for their PCIe
GPP port and internal bus devices.
Change-Id: I386df908ce5451b4484be2a2e4a9018c3d47d030
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Different models within family 17h have different PCI IDs for their data
fabric PCI devices.
Change-Id: I44f8d32c950710e962dc519495b08c92f357ed20
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The code uses PCI_DEVICE_ID_AMD_17H_MODEL_101F_NB instead;
Change-Id: Ia88550d377643741f78ff068e57d6a2d783306f3
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The code that uses the GPU device ID uses the correct ATI vendor ID, but
the description wrongly used AMD as vendor. In the AMD APUs the GPU PCI
device and the corresponding audio controller use the ATI PCI vendor ID
while all other PCI devices in the SoC use the AMD PCI vendor ID.
Also move the two entries in a separate section right below the one they
were in.
Change-Id: Ia0b5bd4638f5b07c487f223321872563b36337e9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This fixes all of the current code in coreboot/src where a bare
unsigned is used incorrectly. A follow-on will fix the comments
so that we can enable the unsigned lint checker for src/coreboot.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I37f34a95bb1894e70cd9e076d4b81ebac665eaeb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47482
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
List of changes:
1. Add new PCH ID 0x5181 into device/pci_ids.h
2. Update new PCH ID into common lpc.c
3. Add new PCH ID description into report_platform.c
TEST=Able to build and boot ADLRVP with new PCH ID.
Change-Id: I4343b7343876eb40c2955f6f4dd99d6446852dc0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47474
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move this function to pci_ops.c, which is already included in the smm
build. This is required to use this function in elog functionality,
which is called from SMM.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ie5583c04366c9a16bc1b00a6892d39eeafe5da49
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
As an intermediate step for CB:45150, add an additional Kconfig option
which is used to configure bus mastering for any devices and use
PCI_ALLOW_BUS_MASTER to allow coreboot setting the bus mastering bit in
general.
Change-Id: I33b37a79022007a16e97350db61575b63fa8256b
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45149
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change drops the PCI IDs for Jefferson Peak and Harrison Peak
CNVi modules from wifi/generic drivers as well as pci_ids.h. These IDs
actually represent the CNVi WiFi controller PCI IDs and are now
supported by intel/common/block/cnvi driver.
The only ID that is being dropped without adding support in
intel/common/block/cnvi driver is
PCI_DEVICE_ID_HrP_6SERIES_WIFI(0x2720) since this was not found in the
list of PCI IDs for any SoC.
Change-Id: I82857a737b65a6baa94fb3c2588fe723412a7830
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46866
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds PCI IDs for CNVi WiFi/BT controllers for CML, GLK,
ICL, JSL and TGL.
Change-Id: Id45f65d0ef5a7782c08ddd70eb22b26072c8ef4b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Bug=None
Test=Enabled the device on TGLY RVP and tested that the codec is
reflected in SSDT. Checked sound card binding works
and soundwire drivers are enabled in kernel.
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: Ia7358927fe8531e609ebe070bef259a2bbc09093
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Move the macros for printing debug information to debug.h in the
common console include directory and device include file.
These are available if the platform selects DEFAULT_CONSOLE_LOGLEVEL_8.
The macros could be used by any platform.
Change-Id: Ie237bdf8cdc42c76f38a0c820fdc92e81095f47c
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add general debug macros that print resource information.
These are available to select if DEFAULT_CONSOLE_LOGLEVEL_8.
The macros are helpful in debugging complex resource allocation
with multiple buses. The macros are moved from soc/intel/xeon_sp,
where they were originally developed.
Change-Id: I2bdab7770ca5ee5901f17a8af3a9a1001b6702e4
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I4077b9dfeeb2a9126c35bbdd3d14c52e55a5e87c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45404
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Iee2ffb3b5170cd4c630f2b26d1eb418b239a8e23
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46629
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The work done by enable_static_devices() and scan_generic_bus()
is common and can be used by other device handlers to enable a
single static device.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: Ibfde9c4eb794714ebd9800e52b91169ceba15266
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I8f182fff45806912da2390939a6652932501d7c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
This change adds a helper function `pci_dev_is_wake_source()` that
checks PME_STATUS and PME_ENABLE bits in PM control and status
register to determine if the given device is the source of wake.
BUG=b:169802515
BRANCH=zork
Change-Id: I06e9530b568543ab2f05a4f38dc5c3a527ff391e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
We don't want unnecessary die() calls to spread throughout coreboot.
Chances are high that we'd add a NON_FATAL_DIE Kconfig eventually.
Change-Id: I01c7efdf23672bad3a195b7dc1565a3cc8a087bd
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46046
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add IGD Device ID and MCH Device ID for Jasperlake.
Reference is taken from Jasperlake EDS volume 1(Document Number:
613601).
TEST=Build and boot Jasperlake platform.
Change-Id: I00ee7950ffa378b428a76bf367a9a05ab287e7ed
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Change-Id: I740d0d756599688165458a9c6e925d5d94754bb2
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45604
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Previously, SMBUS support was not required for Apollo Lake, since the
SPD was read inside FSP-M, during memory initialization. However, the
Kontron mAL-10 COMe module contains Nuvoton HWM chip that is connected
to the processor via SMBUS. This patch adds SMBUS common driver support
for Apollo Lake to initialize this HWM.
TEST = After loading the nct7802 module on the Kontron mAL-10 with Linux
OS, we can read the hwm registers, see temperature and fan speed:
coretemp-isa-0000
Adapter: ISA adapter
Package id 0: +52.0°C (high = +110.0°C, crit = +110.0°C)
Core 0: +52.0°C (high = +110.0°C, crit = +110.0°C)
Core 1: +52.0°C (high = +110.0°C, crit = +110.0°C)
Core 2: +53.0°C (high = +110.0°C, crit = +110.0°C)
Core 3: +53.0°C (high = +110.0°C, crit = +110.0°C)
nct7802-i2c-0-2e
Adapter: SMBus CMI adapter cmi
in0: +3.35 V (min = +0.00 V, max = +4.09 V)
in1: +1.92 V
in3: +1.21 V (min = +0.00 V, max = +2.05 V)
in4: +1.68 V (min = +0.00 V, max = +2.05 V)
fan1: 0 RPM (min = 0 RPM)
fan2: 1729 RPM (min = 0 RPM)
fan3: 0 RPM (min = 0 RPM)
temp1: +53.5°C (low = +0.0°C, high = +85.0°C)
(crit = +100.0°C) sensor = thermistor
temp4: +53.0°C (low = +0.0°C, high = +85.0°C)
(crit = +100.0°C)
temp6: +0.0°C
Change-Id: I408ef84ede27a45fb057e22b2757fa6e66277ddd
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44475
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The device is a PCIe Gen2 to SD 4.0 card reader controller to be
used in the Chromebook. The datasheet name is GL9755S and the revision
is 05.
The patch sets LTR value.
Signed-off-by: Ben Chuang <benchuanggli@gmail.com>
Change-Id: I16048dde348be248c748d50ca4a8a62c8a781430
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
RMW (read/modify/write) ops on PnP devices has never been so simple.
The semantics also allow the compiler to emit valid warnings if the
input parameters would overflow, which are silenced when the cast is
placed outside of the function.
Change-Id: Ica01211af2a9a00aed98880844a836f6b7957b14
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42134
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When <device/pnp.h> is needed, it is supposed to provide <device/pnp_type.h>.
Change-Id: I0e479e2abdb6cfb8633840db2222ce5397fe7d55
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45403
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When <device/pnp.h> is needed, it is supposed to provide <device/pnp_def.h>.
So remove redundant <device/pnp_def.h> includes.
I'll remove also <device/pnp_type.h> in a separate patch.
Change-Id: Ib9903ae456c32db4ba346020659c17c27a939e89
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add method for converting DDR4 speed in MHz to MT/s. Checks that MHz is
within a speed grade range.
BUG=b:167155849
TEST=ddr4-test unit test
BRANCH=Zork
Change-Id: I1433f028afb794fe3e397b03f5bd0565494c8130
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I68590605e261ecaace9f3cea28cfa6ec3b913a8a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Ie325541547ea10946f41a8f979d144a06a7e80eb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The build error `incompatible-pointer-types` occurs while using
`pci_dev_request_bus_master` as part of device ops
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I3b1ce85b8db1ddf9ac860415edbe64694b91b3d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45122
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add PCI IDs for Intel's Dynamic Tuning Technology (DTT) for ADL.
Also add NULL terminator at end of pci_device_ids.
Change-Id: If25b1f562567a833683b0b8796bd1d6cac0bd490
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45140
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add PCI IDs for Intel's Image Processing Unit (IPU) for ADL.
Also add NULL terminator at end of pci_device_ids.
Change-Id: I327828d676422fc6162fadffd9b39529ecb89ace
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
1. Add CPU, SA, PCH & IGD DIDs table into report_platform.c
2. Add additional EHL SA DID in pci_ids.h
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I5c98089873b17f82560eba13c7de3353b6d3e249
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Convert 0X -> 0x
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Iea3ca67908135d0e85083a05bad2ea176ca34095
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The bus master bit is set at many places in coreboot's code, but the
reason for that is not quite clear. We examined not setting the
bus master bit whereever possible and tried booting without it,
which worked fine for internal PCI devices but not for PCIe. As a PCIe
device we used a Samsung M.2 NVMe SSD.
For security reasons, we would like to disable bus mastering where
possible. Depending on the device, bus mastering might get enabled
by the operating system (e.g. for iGPU) and it might be required for
some devices to work properly. However, the idea is to leave it disabled
and configure the IOMMU first before enabling it.
To have some sort of "backwards compatibility", add a method which
configures bus mastering based on an additional config option. Since
CB:42460 makes usage of this treewide, enable it by default to keep the
current behaviour for now.
Tested with Siemens/Chili, a Coffee Lake based platform.
Change-Id: I876c48ea3fb4f9cf7b6a5c2dcaeda07ea36cbed3
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42459
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The code using the macro was found not working after finally enabling
the HDA PCI device on the hermes board.
Fix a typo to generate the correct verbs.
Tested on prodrive/hermes.
Change-Id: I953c2e9fbebc1f02bdf71ce868a95f578300c3a1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44900
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
'drm_dp_helper.h' file is duplicated and not used.
Change-Id: Ibb08f7ff91c3914940dfe899be331b06e292c7c9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This PCI ID is required in order for the CML devices to perform
SSDT generation for DPTF.
CML Processor, EDS, Vol 1,
Table 9-5, Section 9.2.
BUG=b:158986928
BRANCH=puff
TEST=builds
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Change-Id: I94aea6b9e0f60656827daada7b2cc2741604b8b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Andrew McRae <amcrae@google.com>
|
|
Add additional Elkhart Lake specific SA IDs.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I41af9b17b8121f3b47f2242d9beeec297893b378
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40854
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Praveen HP <praveen.hodagatta.pranesh@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9ea191e5076e2f055405dc34d46dbbb8cfb0015e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44106
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
