| Age | Commit message (Collapse) | Author |
|---|
|
Upcoming patches for the Linux kernel (5.6 ?) would like to consume
information about the USB PD ports that are attached to the device. This
information is obtained from the CrOS EC and exposed in the SSDT ACPI
table.
Also, the device enable for this PCI device is moved from ec_lpc.c to
a new file, ec_chip.c, where EC-related ACPI methods can live. It
still allows other code to call functions on device enable (so that
PnP enable for the LPC device still gets called).
BUG=b:146506369
BRANCH=none
TEST=Verify the SSDT contains the expected information
Change-Id: I729caecd64d9320fb02c0404c8315122f010970b
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Serves two purposes:
(1) On some platforms, FSP initialization may cause a reboot.
Push clearing the recovery mode switch until after FSP code runs,
so that a manual recovery request (three-finger salute) will
function correctly under this condition.
(2) The recovery mode switch value is needed at BS_WRITE_TABLES
for adding an event to elog. (Previously this was done by
stashing the value in CBMEM_ID_EC_HOSTEVENT.)
BUG=b:124141368, b:35576380
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I30c02787c620b937e5a50a5ed94ac906e3112dad
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Set CPU ID and cores to EC then EC will adapt power table
according to the CPU ID and number of cores.
BUG=b:148126144
BRANCH=None
TEST=check EC can get correct CPU id and cores.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I23f5580b15a20a01e03a5f4c798e73574f874c9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38566
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new functions to get (from the EC):
1) The number of USB-PD ports
2) The capabilities of each port (EC_CMD_GET_PD_PORT_CAPS)
BUG=b:146506369
BRANCH=none
TEST=Instrumented calls to these and verified the data
Change-Id: I57edbe1592cd28b005f01679ef8a8b5de3e1f586
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The new host command provides these static capabilities of each USB-PD port:
1) Port number
2) Power role: source, sink, dual
3) Try-power role: none, sink, source
4) Data role: dfp, ufp, dual
5) Port location: these come from power_manager
BUG=b:146506369
BRANCH=none
TEST=compiles
Change-Id: I923e4b637a2f41ce173d378ba5030f1ae8c22222
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add new mailbox command support. Set CPU ID and cores to EC.
EC will according to different CPU to set different power table.
BUG=b:148126144
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I135d2421d2106934be996a1780786f6bb0bf6b34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
The firmware configuration (fw_config) field is store in the CBI EEPROM
and it should be used to make firmware customization instead of
sku/variant id.
BUG=b:145519081
TEST=builds
Change-Id: I790998a29e724ecdff8876cca072267537b7cea6
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Copy ec_commands.h directly from Chromium OS EC repo at sha e57217a250.
This is needed for the FW_CONFIG CBI field definition.
Change-Id: Id010721033ebe32ac9c9482d666cf790442a26ee
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
IMD provides support for small and large allocations. Region IMD Small memory is 1 KB
with 32 Bytes alignment, this region holds smaller entries without having to reserve a
whole 4 KB page. Remaining space is assigned to IMD Large to hold various regions with
4 KB alignment.
The UCSI kernel (kernel version 4.19) driver maps the UCSI_ACPI memory as not cached.
Cache mapping is set on page boundaries and all IMD Small is within the same page.
If another driver maps the memory as write-back before the UCSI driver is loaded then
the UCSI driver will fail to map the memory as not cached.
Placing UCSI_ACPI in IMD Large region will prevent this mapping issue since it will
now be located within its own page. This patch will force UCSI_ACPI region to be
located in IMD Large region.
BUG=b:144826008
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: Id00e76dca240279773a95c8054831e05df390664
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38414
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Prevent iasl remarks about unused parameters.
BUG=N/A
TEST=build
Change-Id: I54fa4712e618038fdd5a96c2012c2ec64ca34706
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Assume that LIMIT_POWER is not requested if the ec does not support it.
Do this by checking the command code in the response message instead
of return value.
BUG=b:146165519
BRANCH=None
TEST=Boot puff with EC which does not support LIMIT_POWER param.
Change-Id: Ib2f5f69a53f204acebfab3e36aab2960eeec1204
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
If the EC doesn't support the EARLY_EC_SYNC we don't properly set power
limits to reasonable defaults and can wedge the AP by browning out at
the end of vboot.
BRANCH=none
BUG=b:146165519
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I4e683e5a1c5b453b3742a12a519cad9069e8b7f7
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37930
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I05422ee4b0aa5c02525ef0b4eccb4dc3ecf871e8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32822
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ACPI method TEVT is reported as unused by iASL (20190509) when ChromeEC support is not
enabled. The message is “Method Argument is never used (Arg0)” on Method (TEVT, 1, NotSerialized),
which indicates the TEVT method is empty.
The solution is to only enable the TEVT code in mainboard or SoC when an EC is used that uses
this event. The TEVT code in the EC is only enabled if the mainboard or SoC code implements TEVT.
The TEVT method will be removed from the ASL code when the EC does not support TEVT.
BUG=N/A
TEST=Tested on facebook monolith.
Change-Id: I8d2e14407ae2338e58797cdc7eb7d0cadf3cc26e
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Commit 77ad581ce [chromeec: PS2K node can't be under SIO node]
moved the PS2K ACPI device from under the SIO device to under
the LPCB, and while this fixed the keyboard under Windows for
Skylake devices, it was insufficient for Baytrail and Braswell
devices (and likely Apollo Lake/Gemini Lake too).
Moving the PS2K device under PCI0 allows the PS2K to be functional
under Windows for all Chrome-EC platforms.
Test: build/boot various Chrome-EC devices from IVB, HSW, BDW,
BYT, SKL, BSW, and KBL platforms, verify keyboard functional
under both Linux (4.x and 5.x) and Windows 10.
Change-Id: If773eea69dc46030b6db9d64c3855be49951d4c0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37542
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ACPI methods to the Wilco EC for controlling a privacy screen
on the device.
BUG=b:142237145, b:142656363
TEST=none
Change-Id: Ic3c136f9d2de90eeb3c9e468e4c7430ccf6dcc42
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36044
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I09bca1897920871a6b29c25dc2bad94a8061da29
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37038
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch moves the traditional POSIX stdbool.h definitions out from
stdint.h into their own file. This helps for using these definitions in
commonlib code which may be compiled in different environments. For
coreboot everything should chain-include this stuff via types.h anyway
so nothing should change.
Change-Id: Ic8d52be80b64d8e9564f3aee8975cb25e4c187f5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This avoids a lot of if (CONFIG(ELOG_GSMI)) boilerplate.
Change-Id: I87d25c820daedeb33b3b474a6632a89ea80b0867
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36647
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All of the EC_EVENT_* macros can be replaced with the EC_HOST_EVENT_*
macros defined in ec_commands.h, which is synchronized from Chromium OS
ec repository.
BRANCH=none
BUG=none
TEST=emerge-kukui coreboot
Change-Id: I12c7101866d8365b87a6483a160187cc9526010a
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Quite a few new functions added here in order to support the use-case
of performing EC software sync within coreboot.
Most of these functions are related to retrieving the EC's hash, and
writing a new image into the EC's flash.
BUG=b:112198832
BRANCH=none
TEST=With whole patch series, successfully performed EC software sync
Change-Id: I0d3c5184dbe96f04b92878f2c19c7875503a910a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change all uN integral types to uintN_t. Make the names of host
command params/responses consistent. Use static struct initialization
to ensure all fields are initialized.
BUG=none
BRANCH=none
TEST=compiles
Change-Id: Ibe1e29e88975c85eea215adedc5f5e483243e0d6
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
ACPI Version 6.3 Section 6.1: "A device object must contain either an _HID
object or an _ADR object, but should not contain both."
Change-Id: If3ee38f3eaa8e6d1c1b0393d0ba289f708e0ae5e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36293
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ACPI Version 6.3 Section 6.1: "A device object must contain either an _HID
object or an _ADR object, but should not contain both."
Found-by: ACPICA 20191018
Change-Id: Ic0bcaa37ac017ab61e1fb4e78d3c7dfbbcc0899d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
ACPI Version 6.3 Section 6.1: "A device object must contain either an _HID
object or an _ADR object, but should not contain both."
Change-Id: Ieb54664a6528ce67634991f64a5f3c411822cdf4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36260
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7a7bcb56523d595e8d4f32849aac53d66d416a12
Signed-off-by: Greg V <greg@unrelenting.technology>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35866
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Don't set a default bus type for the Chrome EC on x86. The platform
must select the bus, typically LPC or ESPI.
BUG=b:140055300
TEST=Build tested only
Change-Id: I736cb9e43292a1b228cd083ca81a8e5db383e878
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35154
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
It's been some time and there are 1420 new commits. Including one that
allows reproducible builds \o/ and one that breaks building with empty
$(CC) :-/
Change-Id: I5e81d5a2f1018481b9103fc5a1f4b8c72fb9deec
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30679
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fastboot support in vboot_reference is unused, unmaintained, and
produces compile errors when enabled. Since there is no current
or planned use cases for fastboot, remove it.
BUG=b:124141368, chromium:995172
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I06ea816ffb910163ec2c3c456b3c09408c806d0b
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35002
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Intel platforms using eSPI EC communication have just been enabling
the EC_GOOGLE_CHROMEEC_LPC option for simplicity. This does basically
the same, but at least marks it as eSPI in Kconfig for clarity.
BUG=b:140055300
TEST=Build tested only.
Change-Id: Ib56ec9d1dc204809a05c846494ff0e0d69cf70ea
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35128
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These are required to cover the absensce of .data and
.bss sections in some programs, most notably ARCH_X86
in execute-in-place with cache-as-ram.
Change-Id: I80485ebac94b88c5864a949b17ad1dccdfda6a40
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35003
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
After ChromiumOS CL:1293132 and CL:1295890, Chrome EC can store the flag
telling if the last reboot was triggered by AP watchdog for some boards
(e.g., Kukui).
This CL adds a new function google_chromeec_get_ap_watchdog_flag(),
which reads the AP watchdog flag from Chrome EC, and updates the tables
of reset causes and reset flags.
A new Kconfig option CHROMEOS_USE_EC_WATCHDOG_FLAG is added for
elog_handle_watchdog_tombstone() to determine if watchdog reset was
triggered by the AP watchdog flag from EC instead of the tombstone in
AP.
BUG=b:109900671,b:118654976
BRANCH=none
TEST=test with https://review.coreboot.org/c/coreboot/+/31843
Change-Id: I7a970666a8c6da32ac1c6af8280e808fe7fc106d
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Copy ec_commands.h directly from ChromiumOS EC repository (CL:1520574).
Since ec_commands.h already defines usb_charge_mode and only
USB_CHARGE_MODE_DISABLED is used in coreboot, enum usb_charge_mode is
removed from ec.h.
To avoid redefinition of the BIT macro, #ifndef check is added to
include/types.h.
BUG=b:109900671,b:118654976
BRANCH=none
TEST=emerge-kukui -j coreboot
Change-Id: I7ed5344fc8923e45e17c3e2a34371db6f80b079d
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31885
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
google_chromec_get_event() depends on the main copy of EC which is
used by ACPI subsytem in the kernel for querying events.
google_chromeec_get_event() also clears the event from EC. Thus if the
kernel has to identify the wake source, it has no way to do that. Thus
instead depend on events_copy_b to log the wake source. Please look at
go/hostevent-refactor for more info.
BUG=b:133262012
BRANCH=None
TEST=Hack hatch bios and make sure hostevent log is correct.
Change-Id: I39caae2689e0c2a7bec16416978877885a9afc6c
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
For files built in ramstage and smm -classes, testing
for !__PRE_RAM__ is redundant.
All chip_operations are exluded with use of DEVTREE_EARLY
in static devicetree, so garbage collection will take care
of the !__SMM__ cases.
Change-Id: Id7219848d6f5c41c4a9724a72204fa5ef9458e43
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
These are only referenced inside auto-generated static.c
files, and util/sconfig also generates the declarations
automatically from source file pathnames.
Change-Id: Id324790755095c36fbeb73a4d8f9d01cdf6409cb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34979
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4c6238b0e5f41fcc667baf6b486c7fff4c90a7cb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34944
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This cleans up .config file from unused wilco symbols.
Change-Id: I813d3fe57b97e2c1ba67e1e3674de256c2529029
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34539
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The BBST() method writes an updated status flag mask that is intended
to be stored back in the battery object. This value needs to be
passed as a reference to an object to prevent it from being evaluated
at the time the method is loaded or it will not actually update the
BSTP value in the battery device.
This was tested by instrumenting the _BST method in the primary
battery and ensuring the value can be updated by the BBST method.
Change-Id: Ia8e207a2990059a60d96d8e0f3ed3c16a55c50f4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ifdb2dee08da45d698174583ee5ed44bf5a0243ff
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
'else' is not needed after a 'break' or 'return'.
Change-Id: I98d0ab0d139186b312e8c1086c475ba6ef0b7d3b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
We are seeing an EC interrupt after setting the EC RAM offset that
indicates that the EC should transition to S0ix mode and this is
preventing the kernel from going into S0ix on the first try.
As a workaround if we read back from the EC RAM while still in the
_DSM handler it seems to prevent this problem.
BUG=b:130644677
BRANCH=sarien
TEST=ensure s0ix entry works on the first try with sarien
Change-Id: Id607c4c2b14b79d0cd1bcea0c2032be2f2c0c141
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33455
Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds support for the UCSI specification in order to
provide information about the Type-C port and an interface to
perform power and data role swap.
This change is split across the DSDT and SSDT, with the shared
memory and operation region declared in the SSDT after being
allocated in CBMEM.
The OS will fill in the registers in the system memory region and
then call the _DSM method wtih a read or write argument. The DSM
method will copy the required registers to/from the system memory
and the EC and perform the write or read action.
Responses from the EC will generate a new SCI with event code 0x79
which will notify this UCSI ACPI device and the OS driver will take
action to read status from the EC.
BUG=b:131083691
Change-Id: I438a2bdfaf6720acd8354e0339dcef2844b63a4e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This command is working as written, but it is not actually correct
as to what the format of the command should be. Fix this and add
define the other radios. There is no change in the command send to
the EC.
Change-Id: Ia551b08561b673d27bec2f900d97b746699b30c4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
On Wilco devices, if any of the coreboot stages fails with a fatal
error, set the diagnostic LEDs with the Wilco EC. The last saved
post code is used to determine the error code sent to the EC.
BUG=b:124401932
BRANCH=sarien
TEST=build coreboot for sarien and arcada platforms
TEST=Remove DIMM module, confirm diagnostic LED pattern for memory
failure (2 amber, 4 white).
TEST=Forced a fatal error in both bootblock and verstage to confirm
diagnostic LEDs during these stages. This works on cold-boots only. Bug
b:132622888 tracks the mailbox failures on warm boots.
Change-Id: If865ab8203f89e499130f4677fec166b40d80174
Signed-off-by: Keith Short <keithshort@chromium.org>
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Adds support for the KB_ERR_CODE command on the Wilco EC. This command
is used to drive diagnostic LEDs on the platform after a failed boot.
This change also adds the Wilco EC mailbox command support to bootblock
and verstage so that those stages can use the KB_ERR_CODE command.
BUG=b:124401932
BRANCH=sarien
TEST=build coreboot for sarien and arcada platforms
Change-Id: I96d17baf57694e4e01c676d80c606f67054cd0c3
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32776
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The EC can return a board ID value similar to the Chrome EC.
In order to use this for the board version returned by SMBIOS
this commit implements the board_id() function for mainboards
that use this EC.
BUG=b:123261132
TEST=Check /sys/class/dmi/id/board_version to see that it
is reflecting the value that the EC provides.
Change-Id: I3fbe0dc886701f37d2424fe7a2867fd860fa1ec0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32276
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This progress code enables keyboard backlight control that
otherwise would only work 30 seconds after boot. This code
is already defined but it was not being sent by coreboot.
It is run in the "post device" step between the other defined
progress codes.
BUG=b:130754032
Change-Id: Ica6c622e568cb236c17bf3edb6639d0177510846
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I23bc0191ca8fcd88364e5c08be7c90195019e399
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: David Guckian
|
|
Change-Id: I3b852cae4ef84d257bf1e5486447583bdd16b441
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
I added a method to fill out the _BIX package structure but never
hooked it up to the expected _BIX method that the OS uses.
This change adds _BIX method and uses the existing method to fill
it out. It also adds ^ before the _UID in _BIF to match _BIX as
the _UID is one level above the method.
Change-Id: I0de91369b6780fd9432990732c1078a73f6a3419
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
When using FSP with debug enabled it takes too long to get to ramstage
and send the first progress code to the EC. The same thing has been
reported to happen when 2x16GB memory is installed.
BUG=b:127875364
TEST=boot with FSP debug and ensure EC does not try to turn off the
system while it is still booting.
Change-Id: I5676354f5e53540273a9029411507f91864735a1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This reverts commit 51169b7dda4a1978d622e329a1c40e384471c165.
I was not ready to enable this option yet, until it is enabled
in depthcharge it needs to stay off in coreboot or depthcharge
will attempt to do software sync without a proper driver.
Change-Id: I4840812d0541f822502cfc5c66bed27edf4d2ecc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32007
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will be used to distinguish the mainboard SKU so that the
correct EC firmware can be bundled with the board.
This is read from EC RAM so it can be used by an ACPI method in
the future.
BUG=b:119490232
Change-Id: I71b8017fc4b88e793dfe709e1cb1ab0f0bcdc4fa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable software sync by default if VBOOT is enabled.
The slow update option is also needed, but this is moving
to depthcharge so it is not defined here.
Change-Id: I046661fae7315f84e96293532b4e1568558df962
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
If the command does not respond the driver should not wait for
it to complete before returning.
Tested with SMI debug enabled to ensure that the final command
does not report a failure.
Change-Id: I7c1bfa19a92e8332ac1aa6ff95f94ff4cbdf789d
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Ie7afe77053a21bcf6a1bf314570f897d1791a620
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
To ensure the power button functions as expected in firmware ensure
that the EC is not in "S0ix supported OS" mode and expecting the
power button to be handled by the virtual button interface.
BUG=b:128409889
TEST=Verify that the power button works at the developer screen
when the system is rebooted from within Chrome OS. Also ensure
that it works when external warm reset signal is asserted by H1.
Change-Id: Ic323515e3b8be08bac4f0f82e25f2f78c2f22833
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Both tent mode (0x01) and tablet mode (0x02) should be considered tablet
mode by ChromeOS.
BRANCH=none
BUG=b:122052438
TEST=ChromeOS enters tablet mode when lid angle exceeds 180
Change-Id: I89ba8141350fc628c8cff89d5f33aa47c6ae6afe
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch is a raw application of
find src/ -type f | xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g'
Change-Id: I6262d6d5c23cabe23c242b4f38d446b74fe16b88
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ifda495420cfb121ad32920bb9f1cbdeef41f6d3a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31698
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The function (preprocessor macro) we need is defined
in <endian.h> not <swab.h>.
Change-Id: I3a86c7050bf853e3a56a15421132240e19f40912
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31704
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I91158452680586ac676ea11c8589062880a31f91
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31692
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Various instances of google_chromeec_command() can return non-zero number
(both positive and negative) to indicate error -- fixing cbi_get_uint32()
and cbi_get_string() so they follow the same convention.
BUG=b:123676982
BRANCH=kukui
TEST=build with kukui/flapjack configurations
Signed-off-by: YH Lin <yueherngl@google.com>
Change-Id: I7f0a8a61d01d942cba57036a17dd527fdbbf940c
Reviewed-on: https://review.coreboot.org/c/31585
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch clarifies the definition of google_chromeec_command.
Currently absence of the definition isn't causing any problem because
wrapper APIs check 'ret != 0' or wrapper APIs check 'ret < 0' for an
interface which returns only negative error codes.
However, there is a chance that a new wrapper API will be addedl which
check 'ret < 0' to catch errors, assuming other interfaces behave the same.
Or existing wrapper APIs will be broken as soon as they're compiled for
another interface.
BUG=chromium:935038
TEST=none
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: I2ce7109b5f2a1d5294f167719730bc1f039ba03f
Reviewed-on: https://review.coreboot.org/c/31613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This change fixes the power status events for AC and battery
events from the EC. The register that was being used is not
returning the expected information.
BUG=b:125472740
TEST=enable ACPI debug in the kernel and verify that AC and
battery insert/remove are detected properly.
Change-Id: I15f71fcf0ca6aa9438e951865787c9fc273792d8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use AGPIO 10 as the EC sync interrupt for MKBP events for sensor data.
On this platform, interrupts are routed via the GPIO controller so need to be
registered using GpioInt instead of Interrupt.
BUG=b:123750725
BRANCH=grunt
TEST=MKBP events still received (with matching EC and kernel changes)
Change-Id: If499d24511bbaa7054207b7e0b98445723332c4f
Signed-off-by: Edward Hill <ecgh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add an ACPI device that is compatible with the Intel Virtual
Button kernel driver for reporting tablet mode state and various
virtual button events that may come from the EC.
This driver is used in Windows and in the Linux kernel at
drivers/platform/x86/intel-vbtn.c
Because of a check in the kernel driver it expects the board to
define the SMBIOS enclosure type as convertible for the check at
driver load time for tablet/laptop and dock/undock to work.
The virtual tablet mode button will proxy the tablet mode state
sent from the Sensor Hub to a SW_TABLET_MODE event in the kernel.
The virtual power button is used during S0ix for the EC to wake
the system with an SCI. There are separate press and release
events which are sent for completeness, although the kernel driver
will ignore the release event.
BUG=b:73137291
TEST=Test that the power button can wake the system from S0ix.
Also verify that the device is reported as laptop mode at boot.
Change-Id: I0d5dc985a3cfb1d01ff164c4e67f17e6b1cdd619
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31208
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a separate ACPI device for the Wilco EC event interface so that the
OS drivers can bind to it separately. Since the event handling is all
done with ACPI and not mailbox calls this will be implemented as a
standard acpi_driver in the kernel.
BUG=b:119046283
TEST=veriy device exists in DSDT
Change-Id: I5259a926fb6d5faea835bcdefa12f0184c5adf4a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
1) In the EC _REG method set the flag indicating S0ix support in the OS.
2) Add a function that can be called by the LPI _DSM method to indicate
to the EC that the OS is entering or exiting S0ix.
BUG=b:73137291
Change-Id: Iddc33a08542a6657694c47a9fda1b02dd39d89f7
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31094
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modifiy Makefile so that we can get board ID in verstage.
BRANCH=none
BUG=b:117916698
TEST=manually
Change-Id: Idcdb6e07f565c937185cab811abac0ce47e5e3a7
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/31006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Send required EC command to enable ACPI S3 wake up from lid switch.
BUG=b:120748824
TEST=Put Sarien system into S3 and then wake up from lid switch
successful.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I13f3469847b0886147b8b624311a1ece796f847b
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Commit 8cf8aa2 [ec/google/chromeec: Use common MEC interface]
changed the return mechanism for the checksum on reads/writes
for MEC devices, but incorrectly handled the passed-in csum
parameter by not dereferencing. This led to the returned csum
value always being zero, which causes all EC commands with non-
NULL data_in to fail with a checksum error.
Fix this by storing the returned checksum in a temp variable,
and only assigning to csum when the pointer isn't NULL;
Test: build/boot google/chell, verify EC hello command succeeds,
keyboard backlight turned on at boot.
Change-Id: I7122c3fdc5a19f87f12975ee448728cf29948436
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Send the EC command required to turn the camera power on
and verify that it shows up on the USB bus.
Change-Id: I9e9ba712a11cef85cde91ac21a4b6b5090ef58dc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There is a dependency issue with the EC DPTF code accessing
methods that are external, but once the mainboard includes the
relevant code they become internal and the current version of
IASL used by jenkins will fail to compile it.
Until the new IASL is deployed everywhere wrap the EC DPTF code
and expect that the mainboard will explicitly enable it.
Change-Id: I612ad8f86d424060ca0303d267d7c2915c760173
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add the support needed for DPTF. This includes the methods to
write trip point values, read temperatures, and handle events.
This was tested on a sarien board by inspecting AML debug output
with the kernel while monitoring temperatures and trip points in
sysfs and controlling temperatures with a fan to ensure that when
a trip point is crossed an SCI is generated and the event is
handled properly.
Change-Id: I8d8570d176c0896fa709a6c782b319f58d3c1e52
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29761
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Disable debug output from read/write methods by default
- Use argument to _REG to disable SCI when EC is unregistered
- Change read/write macros to sync level 2 so they can be called
when a mutex is already held
- Define some missing events
Change-Id: Ic65ebbb6a6151444c47b4aeff7429e186856c49a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29760
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Extended events will be handled by the OS kernel driver, but that
driver needs a method exposed by ACPI to read the event data from
the EC and into a buffer.
Tested by generating a hotkey event and reading the buffer from
the Linux kernel driver with acpi_evaluate_object().
Change-Id: Ic8510e38d777a5dd31a5237867313efefeb2b48e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29674
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add EC command to enable WiFi radio and send that command at
startup. Tested to ensure WiFi is functional on a sarien board.
Change-Id: Iac46895c7118567e1eb55ea33051a1662103b563
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29673
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the COM1 ACPI device based on the existing Kconfig option
CONFIG_DRIVERS_UART_8250IO instead of expecting the mainboard to
also define another value for ACPI.
Change-Id: I69361cc2c245cfcad3e4f57567bf56d5a26f0b06
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29672
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I40f8b4c7cbc55e16929b1f40d18bb5a9c19845da
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
OEM name can be stored in CBI. This change can support for fetching
the OEM name from CBI.
BUG=b:118798180
TEST=Verified to get data from CBI
Change-Id: I4938c4d60fcad9e1f43ef69cc4441d1653de7e24
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/29497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
In order to support Multi-DPTF profile, Device DPTF Profile Number is
introduced into EC_ACPI_MEM_DEVICE_ORIENTATION ACPI Space at offset
0x09. This bit field stays along with Tablet Mode Device flag.
BUG=b:118149364
BRANCH=None
TEST=Ensured that the expected DPTF table are loaded in different
modes(base attached/detached and clamshell/360-flipped) on Soraka and
Nautilus.
Change-Id: Ie14916ac16c50cbe0990021e2eb03d5121cd0e07
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Rename EC_ENABLE_TABLET_EVENT config as EC_ENABLE_MULTIPLE_DPTF_PROFILES
since it aligns with the use-case.
BUG=b:118149364
BRANCH=None
TEST=Ensured that the expected DPTF table are loaded in different
modes (base attached/detached and clamshell/360-flipped) on Soraka and
Nautilus.
Change-Id: If147f1c79ceaaed00e17ec80ec6c912a8f7a8c2e
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
EC_SYNC_IRQ from EC to host is level-triggered in practice and
configuring it as edge-triggered on the host results in host missing
events if there are multiple events queued on the EC side. This is
because Linux kernel driver reads one event per irq and the EC does
not de-assert the interrupt line until all events are drained
out. This results in event queue being filled up completely on the EC
and the host failing to see any of those events.
This change configures EC_SYNC_IRQ as level triggered to allow the
host to read events from the the EC as long as the line is asserted.
BUG=b:118949877
Change-Id: Id3fcfa0445f83865d57975a7bbc179dca047ba4c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
|
|
If remaining charge is more than x% of the full capacity, the
remaining charge is raised to the full capacity before it's
reported to the rest of the system.
Some batteries don't update full capacity timely or don't update it
at all. On such systems, compensation is required to guarantee
the remaining charge will be equal to the full capacity eventually.
On some systems, Rohm charger generates audio noise when the battery
is fully charged and AC is plugged. A workaround is to do charge-
discharge cycles between 93 and 100%. On such systems, compensation
was also applied to mask this cycle from users.
This used to be done in ACPI, thus, all software components except EC
was able to see the compensated charge. This patch is part of the
effort of moving the logic to EC. With this and the EC changes, EC
can see what the rest of the system sees, thus, can control LEDs
synchronously (to the display percentage).
Another rationale of this move is EC can perform more granular and
precise compensation than ACPI since it has more knowledge about the
battery and the charger.
CQ-DEPEND=CL:1312204
BUG=b:109954565,b:80270446,chromium:899120
BRANCH=none
TEST=Verify charge LED changes to white (full) on Sona synchronously
to the display percentage.
TEST=Verify charge LED changes to blinking white (low) on Sona
within 30 seconds synchronously to the display percentage.
Change-Id: I0b51911b90dc2e7fcf5c730c54d9fda1fea76aa9
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/29441
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add a way for the mainboard to provide a wake pin that the EC
will use to wake the system. This defines a _PRW object.
Change-Id: I94954104bbb8226683c37abc8c0465fe3c62a693
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29408
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The speakers start up muted, and the EC must be told by the BIOS
to unmute it. This helps prevent popping noises on boot/resume.
Change-Id: I693f1d01e46e19362ef8fd0d5b3f4930967b5a12
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29203
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ACPI devices for the basic SuperIO functionality provided by the EC
for PS/2 keyboard, PS/2 mouse (trackpad emulation), and legacy UART.
The specific defines to enable these devices should be declared by the
mainboard before including this ASL, the same as the Chrome EC behavior.
Change-Id: I910940ebf26b8758ab12d695e1eba9c668c640c6
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add methods to handle ACPI EC events at runtime. Currently only
some common events are handled like lid switch and battery info,
and the event status is printed for debug on other events.
Change-Id: Ic0bd070940c8a2dfa6a251f3464301418bdb69c1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add the expected objects (_BST, _BIF, _BIX) for reading battery
information and status from the embedded controller, and the
expected objects for reporting AC power status.
The battery was tested by booting with a battery attached and checking
that it is present in /sys/class/power_supply/BAT0 and that the values
are consistent and within expected ranges.
The AC device was tested by checking the AC status in sysfs when AC
is inserted or removed while the system is running.
Change-Id: Ie996891c383c9e990736690aef9795512ad6d35a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add the base ACPI support for the Wilco embedded controller, using
ASL 2.0 syntax throughout.
This includes the EC device and its resources, as well as the layout
for the EC RAM and the functions needed to read and write to the EC RAM.
The EC RAM address space is typically read/write, and so the ACPI EC
device expects that a defined Field can be read and/or written. With
this EC the read and write address spaces are different. For example,
a read from address zero will return data that is unrelated to what a
write to address zero expects.
This makes using a typical OperationRegion to describe the EC RAM
address space somewhat impracticle, since field definitions would
overlap. Instead, methods are provided for reading and writing to an
EC RAM offset, and the EC RAM layout is defined as a Package that
describes offset+mask for read or write fields within the EC RAM.
Change-Id: If8cfdf2633db1ccad4306fe877180ba197ee7414
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a function for use in bootblock stage that performs early init
of the EC, in particular setting it up for UART passthrough so a
legacy serial port can be used by the host.
This needs to be called by the mainboard that intends to use it
in bootblock in order for the UART to be available in later stages.
Some of the PNP style programming may look odd, but it is following
the EC specification which is not entirely standard. This code has
been tested on a board with this EC and it is functional.
Change-Id: I9d6935a9fdf0d7290a94bf2ee565ef2a7c00ecc7
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29121
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Send a command to the EC on the way into S3 suspend state telling
it to save the PS/2 data, and on resume send it a command for
restoring the PS/2 data that was previously saved.
Change-Id: Ic4b5d6d2656dbb1c476b9211b0d60c71b0cd7b32
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29120
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add EC handlers for specific SMM actions:
- on entry to sleep state tell the EC to save state and to prepare for
the host to enter sleep
- on ACPI enable/disable send command to the EC
- add a function to print SMI reasons when eSPI SMI is received
These need to be called by the mainboard handlers which will be done
when a board is added that uses this EC.
Change-Id: Ibabdc1462e0a8df405f9520244b83684e2ccf2f5
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29119
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The EC expects to receive updates about the BIOS boot progress. This is
used for the EC logging to track system boot completeness. If the EC is
not informed about BIOS progress it will turn the system off 30 seconds
after the boot starts.
Change-Id: I693c3930117db2b69a119aee0380d6f303c4881c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29118
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a chip_operations structure for Wilco EC and hook it into the device
tree so it can be initialized at boot.
Reserve the device resources specified in Kconfig, which will also
create the device IO windows if they have not been created in bootblock.
If the IO windows already exist (becauase they were specified in the
mainboard devicetree.cb) then this will find the existing entry instead.
During device init stage prepare the keyboard for use, which is required
for it to be functional in firmware and OS with this EC. Also send a
command to the EC telling it to pass the power button through to the
host for processing.
Change-Id: I0adb01cf394f939f4a28aeb47fe4d0bcda5957d9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29117
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add EC mailbox commands that are related to the power and state of the
system. These commands include:
- read the power status registers from the EC
- read & clear the power status registers
- helper function to read the current lid state
- tell the EC why the host is about to power off
- tell the EC that the host is about to enter a sleep state
Change-Id: Iaa7051b4006e3c1687933e0384d962516220621f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29116
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add basic supported mailbox commands for this embedded contrlller,
and define some command functions to retrieve and print information
about the EC.
Change-Id: Ibcef7d58e1852fdb2e52b97acd4b51a26dd8cd77
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29115
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add helper functions that make it more convenient to send and receive
the most common types of commands to the Wilco embedded controller.
Change-Id: I9cee1a3b2f9d507f6ecdfae9f4a34ba59056cb91
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29114
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
