| Age | Commit message (Collapse) | Author |
|---|
|
The existing default path of PCI0.LPCB is missing the \_SB prefix and prevents Linux from detecting the TPM.
This is assuming that normally the LPCB device is most commonly on \_SB.PCI0.LPCB.
SSDT excerpt without the patch:
"""
DefinitionBlock ("", "SSDT", 2, "CORE ", "COREBOOT", 0x0000002A)
{
External (_SB_.PCI0.GFX0, DeviceObj)
[...]
External (_SB_.PCI0.SATA, DeviceObj)
External (PCI0.LPCB, DeviceObj)
[...]
Scope (PCI0.LPCB)
{
Device (TPM)
[...]
Scope (\_SB.PCI0.GFX0)
{
Method (_DOD, 0, NotSerialized) // _DOD: Display Output Devices
[...]
"""
SSDT excerpt with the patch:
"""
DefinitionBlock ("", "SSDT", 2, "CORE ", "COREBOOT", 0x0000002A)
{
External (_SB_.PCI0.GFX0, DeviceObj)
[...]
External (_SB_.PCI0.LPCB, DeviceObj)
[...]
External (_SB_.PCI0.SATA, DeviceObj)
[...]
Scope (\_SB.PCI0.LPCB)
{
Device (TPM)
[...]
Scope (\_SB.PCI0.GFX0)
{
Method (_DOD, 0, NotSerialized) // _DOD: Display Output Devices
[...]
"""
After the patch the TPM shows up in /sys/bus/acpi/devices/PNP0C31:00.
Previously it was missing and not detected by the kernel.
Change-Id: I615b4873ca829a859211403c84234d43d60f2243
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/18315
Tested-by: build bot (Jenkins)
Reviewed-by: Nicola Corna <nicola@corna.info>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The selection of the SSC reference frequency for LVDS was based on a
completely unrelated clock.
The `ssc_freq` flag should be set when the SSC reference runs at a
different frequency than the general display reference clock (DREF).
For most platforms, there is no choice, i.e. for i945 and gm45 the SSC
reference always differs from the display reference clock (i945: 66Mhz
SSC vs. 48MHz DREF; gm45: 100MHz SSC vs. 96Mhz DREF), for Nehalem and
newer, it's the same frequency for SSC/non-SSC (120MHz). The only,
currently supported platform with a choice seems to be Pineview, where
the alternative is 100MHz vs. the default 96MHz.
Change-Id: I7791754bd366c9fe6832c32eccef4657ba5f309b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/18186
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Linux kernel expects that power management with ACPI should always be
handled using PowerResource. However, some kernel drivers (e.g. ELAN
touchscreen) check to see if reset gpio is passed in by the BIOS to
decide whether the device loses power in suspend. Thus, until the kernel
has a better way for drivers to query if device lost power in suspend,
we need to allow passing in of GPIOs via _CRS as well as exporting
PowerResource to control power to the device.
Update mainboards to export reset GPIO as well as PowerResource for
ELAN touchscreen device.
BUG=chrome-os-partner:62311,chrome-os-partner:60194
BRANCH=reef
TEST=Verified that touchscreen works on power-on as well as after
suspend-resume.
Change-Id: I3409689cf56bfddd321402ad5dda3fc8762e6bc6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18238
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
If cmos is invalid, it doesn't make sense to read the value before
finding that out.
Change-Id: Ieb4661aad7e4d640772325c3c6b184de1947edc3
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18236
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The default macaddress in rt8168.c can be changed with a cbfsfile
called macaddress. This patch makes it possible to add such a file
using Kconfig at build time.
This also changes the name of the cbfsfile from "macaddress" to
"rt8168-macaddress" to avoid confusion.
Change-Id: I24674d8df11845167b837b79344427ce0c67f4fb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18088
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
o Fix indentation and other whitespace issues,
o Use `const` where applicable,
o Avoid retyping the same constant literals,
o Actually read PCI revision from the device (instead of using the
lowest class byte).
Change-Id: I2c64153c61a51a6a87848360d22f981225812a3b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/18185
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Currently car_stage_entry is defined only in romstage_after_verstage and
as a result when SEPARATE_VERSTAGE is not selected, there is no
entry point into romstage and romstage will not be started at all.
The solution is move out romstage_after_verstage.S from fsp1.1 driver
to skylake/romstage. And add CONFIG_PLATFORM_USES_FSP1_1 to fix the
build and boot issue with this change.
Besides that, rename the romstage_after_verstage to romstage_c_entry
in more appropriate naming convention after this fix.
Tested on SkyLake Saddle Brook (FSP 1.1) and KabyLake Rvp11 (FSP 2.0),
romstage can be started successfully.
Change-Id: I1cd2cf5655fdff6e23b7b76c3974e7dfd3835efd
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/17976
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
To support intel wifi SAR configuration, it is required coreboot
to publish two ACPI objects (WRDS and EWRD) to supply SAR limit
data sets. VPD entry "wifi_sar" is required to supply the raw SAR
limit data.
BUG=chrome-os-partner:60821
TEST=Enable USE_SAR, boot reef to OS, create the VPD entry, reboot,
check the SSDT dump and verify WRDS and EWRD structures.
Change-Id: I6be345735292d0ca46f2f7e7ea61924990d338a8
Signed-off-by: Robbie Zhang <robbie.zhang@intel.com>
Reviewed-on: https://review.coreboot.org/17959
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Fix SPI flash ops regressions after commit:
c2973d1 spi: Get rid of SPI_ATOMIC_SEQUENCING
When spi_flash_cmd() is called with argument response==NULL,
only send out command without reading back the response.
Change-Id: I28a94f208b4a1983d45d69d46db41391e267891d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18082
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
We've found that the SLB9645 TPM sometimes seems to randomly start
returning 0xFF bytes for all requests. The exact cause is yet unknown,
but we should try to write our TIS code such that it avoids bad
interactions with this kind of response (e.g. any wait_for_status()
immediately succeeds because all "status bits" are set in the response).
At least for status and burstCount readings we can say for sure that the
value is nonsensical and we're already reading those in a loop until we
get valid results anyway, so let's add code to explicitly discount 0xFF
bytes.
BRANCH=oak
BUG=chrome-os-partner:55764
TEST=None
Change-Id: I934d42c36d6847a22a185795cea49d282fa113d9
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/420470
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://review.coreboot.org/18006
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
uart_fill_lb() was added to drivers/uart/uart8250mem.c, so when the
Oxford OXPCIe952 Kconfig option is enabled, we were getting an error.
"multiple definition of `uart_fill_lb'"
The new version of uart_fill_lb sets the regwidth depending on the
Kconfig symbol DRIVERS_UART_8250MEM_32, so if that's selected, don't
give DRIVERS_UART_OXPCIE as a choice.
Change-Id: Ife24ab390553b10b2266809595c2e06463de708c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17966
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
SPI_ATOMIC_SEQUENCING was added to accomodate spi flash controllers with
the ability to perform tx and rx of flash command and response at the
same time. Instead of introducing this notion at SPI flash driver layer,
clean up the interface to SPI used by flash.
Flash uses a command-response kind of communication. Thus, even though
SPI is duplex, flash command needs to be sent out on SPI bus and then
flash response should be received on the bus. Some specialized x86
flash controllers are capable of handling command and response in a
single transaction.
In order to support all the varied cases:
1. Add spi_xfer_vector that takes as input a vector of SPI operations
and calls back into SPI controller driver to process these operations.
2. In order to accomodate flash command-response model, use two vectors
while calling into spi_xfer_vector -- one with dout set to
non-NULL(command) and other with din set to non-NULL(response).
3. For specialized SPI flash controllers combine two successive vectors
if the transactions look like a command-response pair.
4. Provide helper functions for common cases like supporting only 2
vectors at a time, supporting n vectors at a time, default vector
operation to cycle through all SPI op vectors one by one.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: I4c9e78c585ad95c40c0d5af078ff8251da286236
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17681
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
FSP v2.0 Specification adds APIs TempRamInit & TempRamExit for
Cache-As-Ram initialization and teardown. Add fsp2_0 driver
support for TempRamInit & TempRamExit APIs.
Verified on Intel Leaf Hill CRB and confirmed that Cache-As-Ram
is correctly set up and torn down using the FSP v2.0 APIs
without coreboot implementation of CAR init/teardown.
Change-Id: I482ff580e1b5251a8214fe2e3d2d38bd5f3e3ed2
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/17062
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
There was an assumption that all SPI controllers could
consume a full page of data to write. However, that
assumption doesn't hold when spi_crop_chunk() indicates
sizes smaller than page size. If the requested offset isn't
page aligned from the start then writes will fail corrupting
data since a page boundary isn't honored.
The spansion driver needed quite a bit more work to honor
the spi_crop_chunk() result. It now mimics the other
driver's code. Also, needed to add spi_crop_chunk() to
marvell/bg4cd SoC to make google/cosmos build. SPI obviously
doesn't work on that platform, but it fixes the build error.
Change-Id: I93e24a5a717adcee45a017c164bd960f4592ad50
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17910
Tested-by: build bot (Jenkins)
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Utilize libgfxinit's support for scaling to simplify the framebuffer
configuration. In case of multiple displays of different resolutions,
we had configured one framebuffer big enough for their union, each
display only showing its respective upper left window. Instead, we use
the smallest resolution now and show the whole image on all displays.
Change-Id: I70a9d92f88ef891703829945264f94ac7eff09b0
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/17492
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Add an alternative gfxinit implementation for textmode. The legacy VGA
plane and textmode is configured through coreboot provided functions.
libgfxinit uses this plane as alternative to the usual high resolution
plane.
Change-Id: Iad0754c50fc6faec35f49583fe1c7cb50ac6c0c5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/17279
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This change adds the required device node in SSDT for defining
GPIO-based fixed voltage regulator.
BUG=chrome-os-partner:60194
BRANCH=None
TEST=Verified that ELAN touchscreen works with exported GPIOs and ACPI
regulator.
Change-Id: I4380aea0929fb7e81dbe83f940e3e51e983819f9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17798
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable default acpi path PCI0.LPCB if TPM support is
selected in the kconfig system and the acpi path is not set via
acpi_name callback in the platform code.
Thanks to Aaron Durbin for providing this fix.
Change-Id: Idb56cafe71efc8a52eee5a5a663478da99152360
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/17855
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add power management type config option that allows mainboards to
either:
1. Define a power resource that uses the reset and enable gpios to
power on and off the device using _ON and _OFF methods, or
2. Export reset and enable GPIOs in _CRS and _DSD so that the OS can
directly toggle the GPIOs as required.
GPIO type needs to be updated in drivers_i2c_generic_config to use
acpi_gpio type so that it can be used for both the above cases.
BUG=chrome-os-partner:60194
BRANCH=None
TEST=Verified that elan touchscreen works fine on reef using exported
GPIOs.
Change-Id: I4d76f193f615cfc4520869dedc55505c109042f6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17797
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
When trying to bring up a device with a malfunctioning TPM2 chip, the
driver currently gets stuck waiting for SPI flow control, causing
bricked devices.
This patch puts a 100 ms cap on the waiting time - this should be
enough even for a longest NVRAM save operation which could be under
way on the TPM device.
BRANCH=gru
BUG=chrome-os-partner:59807
TEST=with a matching change in depthcharge, now a gru with corrupted
SPI TPM comes up to the recovery screen (it was not showing signs
of life before this change).
Change-Id: I63ef5dde8dddd9afeae91e396c157a1a37d47c80
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/17898
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Add a generic I2C-HID driver for these types of devices that
do not need extra functionality. This allows a new device to
be added without having to write a new driver.
The i2c-hid PNP0C50 is automatically added as the _CID for the
device in the ACPI Device.
BUG=chrome-os-partner:58666
TEST=used on eve to describe a new i2c-hid touch controller
Change-Id: I94e9531a72f9bf1d6b3ade362b88883b21b83d0a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17856
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Remove any assumptions required for the drivers using i2c_generic to
have drivers_i2c_generic_config structure at the start of the driver
config. Instead pass in a pointer to drivers_i2c_generic_config from
the calling driver.
Change-Id: I51dc4cad1c1f246b51891abf7115a7120e87b098
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17857
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Update the mrc cache implementation to use region_file. Instead
of relying on memory-mapped access and pointer arithmetic
use the region_devices and region_file to obtain the latest
data associated with the region. This removes the need for the
nvm wrapper as the region_devices can be used directly. Thus,
the library is more generic and can be extended to work on
different boot mediums.
BUG=chrome-os-partner:56151
Change-Id: Ic14e2d2f7339e50256b4a3a297fc33991861ca44
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17717
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
In the case where the RTC is initialized after the battery is
completely drained the bits for power_mode and cof_selection are set up
with wrongly applied masks.
In the case where the RTC is re-initialized again with no power-loss
after the last initialization the bits for cap_sel, power_mode and
cof_selection are not shifted to the right position.
Both errors lead to a wrong initialization of the RTC and in turn to a
way larger current consumption (instead of 120 nA the RTC current rises
to over 2 µA).
This patch fixes both errors and the current consumption is in the right
range again.
TEST=booted mc_bdx1 and verified current consumption of RTC
Change-Id: I8594f6ac121a175844393952db2169dbc5cbd2b2
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/17829
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Don't implement arch or driver -specific code under lib/,
Change-Id: If75980ec5efc622582e2b5e124ad0e7ee3fa39a3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17793
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
- Separate mma code for fsp1.1 and fsp2.0
and restructuring the code
- common code is placed in mma.c and mma.h
- mma_fsp<ver>.h and fsp<ver>/mma_core.c contains
fsp version specific code.
- whole MMA feature is guarded by CONFIG_MMA flag.
Change-Id: I12c9a1122ea7a52f050b852738fb95d03ce44800
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/17496
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
soc_binding.h includes FSP headers which define NULL macro. Because of
this, including stddef.h after soc_binding.h results in NULL being
re-defined. Thus, include stddef.h in soc_binding.h to avoid having
users include stddef.h along with soc_binding.h.
Change-Id: I600083c5d8f672518beaa1119f14f67728a433aa
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17773
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
We have kconfig.h auto-included and it pulls config.h too.
Change-Id: I665a0a168b0d4d3b8f3a27203827b542769988da
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17655
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The MRC cache wants to be able to access the SPI flash boot device.
Allow an easy way to provide that so that there isn't duplicate
spi_flash objects representing the same device.
BUG=chrome-os-partner:56151
Change-Id: Iba92e8bb8a6060cdd327b10f5f8ec23ac61101e7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17715
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This driver applies to 10ec:8168
Previously, this driver resetted the nic and set a hardcoded
MAC address. Now the driver reads a default MAC address
from CBFS in the form of a string:
echo -n "xx:xx:xx:xx:xx:xx" > macaddress
and store the macaddress file in CBFS with the same name.
TESTED on GA-G41M-ES2L and GA-945GCM-S2L:
MAC address was detected
Change-Id: If1af91120fa3efca3f1406334a83ed1e59fbdaf9
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/17672
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
1. Add new structure spi_ctrlr_buses that allows platform to define a
mapping from SPI controller to buses managed by the controller.
2. Provide weak implementations of spi_init and spi_setup_slave that
will be used by platforms using the new interface.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Ia6f47941b786299f4d823895898ffb1b36e02f73
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17561
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Commit 36b81af (spi: Pass pointer to spi_slave structure in
spi_setup_slave) changes the way spi_setup_slave handles the spi_slave
structure. Instead of expecting spi controller drivers to maintain
spi_slave structure in CAR_GLOBAL/data section, caller is expected to
manage the spi_slave structure. This requires that spi_flash drivers
maintain spi_slave structure and flash probe function needs to make a
copy of the passed in spi_slave structure.
This change fixes the regression on Lenovo X230 and other mainboards.
Change-Id: I0ad971eecaf3bfe301e9f95badc043193cc27cab
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17728
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Iru Cai <mytbk920423@gmail.com>
|
|
1. Define a new structure spi_ctrlr that allows platforms to define
callbacks for spi operations (claim bus, release bus, transfer).
2. Add a new member (pointer to spi_ctrlr structure) in spi_slave
structure which will be initialized by call to spi_setup_slave.
3. Define spi_claim_bus, spi_release_bus and spi_xfer in spi-generic.c
which will make appropriate calls to ctrlr functions.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Icb2326e3aab1e8f4bef53f553f82b3836358c55e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17684
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
For spi_setup_slave, instead of making the platform driver return a
pointer to spi_slave structure, pass in a structure pointer that can be
filled in by the driver as required. This removes the need for platform
drivers to maintain a slave structure in data/CAR section.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Ia15a4f88ef4dcfdf616bb1c22261e7cb642a7573
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17683
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1. Use size_t instead of unsigned int for bytes_out and bytes_in.
2. Use const attribute for spi_slave structure passed into xfer, claim
bus and release bus functions.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Ie70b3520b51c42d750f907892545510c6058f85a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17682
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Instead of putting all the functions inline just put the
current implementation into a C file. That way all the implementation
innards are not exposed.
Lastly, fix up the fallout of compilation units not including the
headers they actually use.
Change-Id: I01fd25d158c0d5016405b73a4d4df3721c281b04
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17648
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The same pattern was being used throughout the code base
for initializing the romstage handoff structure. Provide
a helper function to initialize the structure with the S3
resume state then utilize it at all the existing call sites.
Change-Id: I1e9d588ab6b9ace67757387dbb5963ae31ceb252
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17646
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Ibad1ad6bb9eedf2805981623e835db071d54c528
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/17497
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add `libgfxinit` as another option for native graphics initialization.
For that, the function gma_gfxinit() (see drivers/intel/gma/i915.h) has
to be called by the respective northbridge/soc code.
A mainboard port needs to select `CONFIG_MAINBOARD_HAS_LIBGFXINIT` and
implement the Ada package `GMA.Mainboard` with a single function `ports`
that returns a list of ports to be probed for displays.
v2: Update 3rdparty/libgfxinit to its latest master commit to make
things buildable within coreboot.
v3: Another update to 3rdparty/libgfxinit. Including support to select
the I2C port for VGA.
Change-Id: I4c7be3745f32853797d3f3689396dde07d4ca950
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/16952
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Don't build the cmos.default file into cbfs if USE_OPTION_TABLE
isn't specified.
- Don't allow HAVE_CMOS_DEFAULT if HAVE_OPTION_TABLE isn't set.
Change-Id: I92401e892f09fc95d4b3fd7418cdbd10ed033fa8
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17454
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Resetting a Realtek 8168 NIC only makes sense on targets that have
such a device.
Change-Id: I8ac9e8da1d8ecaacb19b4610a9b75f107915d691
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17577
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Runtime write acpi table for TPM driver.
Change-Id: I70896e5874c24f17fca0c48b138ad4917b273f5b
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17425
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
flash_programmer_probe is a property of the spi flash driver and does
not belong in the spi_slave structure. Thus, make
spi_flash_programmer_probe a callback from the spi_flash_probe
function. Logic still remains the same as before (order matters):
1. Try spi_flash_programmer_probe without force option
2. Try generic flash probing
3. Try spi_flash_programmer_probe with force option
If none of the above steps work, fail probing. Flash controller is
expected to honor force option to decide whether to perform specialized
probing or to defer to generic probing.
BUG=None
BRANCH=None
TEST=Compiles successfully
Change-Id: I4163593eea034fa044ec2216e56d0ea3fbc86c7d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17465
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
max_transfer_size is a property of the SPI controller and not of the spi
slave. Also, this is used only on one SoC currently. There is no need to
handle this at the spi flash layer.
This change moves the handling of max_transfer_size to SoC SPI driver
and gets rid of the max_transfer_size parameter.
BUG=None
BRANCH=None
TEST=Compiles successfully.
Change-Id: I19a1d0a83395a58c2bc1614b24518a3220945a60
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17463
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
RW flag was added to spi_slave structure to get around a requirement on
some AMD flash controllers that need to group together all spi volatile
operations (write/erase). This rw flag is not a property or attribute of
the SPI slave or controller. Thus, instead of saving it in spi_slave
structure, clean up the SPI flash driver interface. This allows
chipsets/mainboards (that require volatile operations to be grouped) to
indicate beginning and end of such grouped operations.
New user APIs are added to allow users to perform probe, read, write,
erase, volatile group begin and end operations. Callbacks defined in
spi_flash structure are expected to be used only by the SPI flash
driver. Any chipset that requires grouping of volatile operations can
select the newly added Kconfig option SPI_FLASH_HAS_VOLATILE_GROUP and
define callbacks for chipset_volatile_group_{begin,end}.
spi_claim_bus/spi_release_bus calls have been removed from the SPI flash
chip drivers which end up calling do_spi_flash_cmd since it already has
required calls for claiming and releasing SPI bus before performing a
read/write operation.
BUG=None
BRANCH=None
TEST=Compiles successfully.
Change-Id: Idfc052e82ec15b6c9fa874cee7a61bd06e923fbf
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17462
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The cbmem routines pass back NULL on error. Check for this before using
the pointer.
Addresses coverity issue 1365731 - Dereference null return value
Change-Id: I92995366ffb15afd0950b9a8bbb6fe16252b2c38
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17480
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Stage cache will save ~20ms on S3 resume for apollolake platforms.
Implementing the cache in ramstage to save silicon init and reload
it on resume. This patch adds passing S3 status to silicon init in
order to verify that the wake is from S3 and not for some other
reason. This patch also includes changes needed for quark and
skylake platforms that require fsp 2.0.
BUG=chrome-os-partner:56941
BRANCH=none
TEST=built for reef and tested boot and S3 resume path saving 20ms
Change-Id: I99dc93c1d7a7d5cf8d8de1aa253a326ec67f05f6
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/17460
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
It's very dangerous to set bus master enable, and more so on
a NIC, where random broadcast packets can end up in memory
in unexpected ways.
If your kernel has trouble with the fact that we do not set
bus master enable, you need to fix your kernel.
Change-Id: If07fde7961ad80125567240cb43db036346bef97
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/17559
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Tested-by: build bot (Jenkins)
|
|
The maximum supported rate is 12MHz. Only tested with 4MHz though,
since I couldn't set anything higher on my Linux receiver. But that
works fine with another FT*232H as receiver, whoosh.
Change-Id: Ie39aa0170882ff5b4512f0349f6f86d3f0b86421
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/17477
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Align top of stack to 8 bytes, value documented as FSP1.1 requirement.
Also fix some cases of uintptr_t casted to unsigned long.
Change-Id: I5bbd100eeb673417da205a2c2c3410fef1af61f0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17461
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
After the RTC coin cell has been replaced, the Update Cycle Inhibit
bit must see at least one low transition to ensure the RTC counts.
The reset value for this bit is undefined. Examples have been observed
where batteries are installed on a manufacturing line, the bit's state
comes up low, but the RTC does not count.
Change-Id: I05f61efdf941297fa9ec90136124b0c8fe0639c6
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/17370
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
While the real-time clock updates its count, values may not be correctly
read or written. On reads, ensure the UIP bit is clear which guarantees
a minimum of 244 microseconds exists before the update begins. Writes
already avoid the problem by disabling the RTC count via the SET bit.
Change-Id: I39e34493113015d32582f1c280fafa9e97f43a40
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/17369
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add support for I2C ALPS Touchpad Device Driver.
BUG=none
BRANCH=none
TEST=Build and booted successfully on KBL RVP and Touchpad is working
Change-Id: I78b77bd7c4694ccf61260724f593bd59545c70e6
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/17390
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Device ID remains same for SLB9670 Infineon TPM 1.1 and TPM 2.0
chip. Hence select based on TPM2 Kconfig option.
BUG=none
BRANCH=none
TEST=Build and boot SKL RVP with SPI TPM 2.0 module
Change-Id: I57e63f2f2899d25ed6b797930fd8bf1d1cdc1b1d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/17374
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The end of firmware notification is currently not being tracked
so it's hard to get good data on how long it takes. Update the
code to provide timestamp data as well as post codes.
BUG=chrome-os-partner:56656
Change-Id: I74c1043f2e72d9d85b23a99b8253ac465f62a7f2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17373
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
|
|
Since tlcl library is used other than just vboot driver, ensure that the
library is initialized only once per stage.
BUG=chrome-os-partner:59355
BRANCH=None
TEST=Verified in recovery mode on reef, tlcl library is initialized only
once in romstage.
Change-Id: I6245fe9ed34f5c174341b7eea8db456b45113287
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17364
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Wacom I2C driver can be used by devices other than
touchscreen. e.g. digitizer. So there is no need to name the driver
with touchscreen specific attributes. Only a separate descriptor name
is required that needs to be set by mainboard correctly.
BUG=chrome-os-partner:56246
BRANCH=None
TEST=Compiles successfully.
Change-Id: I0d32a4adae477373b3f4c5f3abbe188860701194
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17341
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This space is read/updated only in recovery mode.
1. During read phase, verify if the hash of MRC data read from
RECOVERY_MRC_CACHE matches the hash stored in TPM.
2. During update phase, calculate hash of training data returned by MRC
and save it in TPM.
BUG=chrome-os-partner:59355
BRANCH=None
TEST=Verified MRC data hash comparison and update operation on reef.
Change-Id: Ifcbbf1bd22033767625ec55b659e05fa7a7afc16
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17274
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1. Re-factor MRC cache driver to properly select RW_MRC_CACHE or
RECOVERY_MRC_CACHE based on the boot mode.
- If normal mode boot, use RW_MRC_CACHE, if available.
- If recovery mode boot:
- Retrain memory if RECOVERY_MRC_CACHE not present, or recovery is
requested explicity with retrain memory request.
- Use RECOVERY_MRC_CACHE otherwise.
2. Protect RW and RECOVERY mrc caches in recovery and non-recovery boot
modes. Check if both are present under one unified region and protect
that region as a whole. Else try protecting individual regions.
3. Update training data in appropriate cache:
- Use RW_MRC_CACHE if normal mode.
- Use RECOVERY_MRC_CACHE if present in recovery mode. Else use
RW_MRC_CACHE.
4. Add proper debug logs to indicate which training data cache is used
at any point.
BUG=chrome-os-partner:59352
BRANCH=None
TEST=Verified that correct cache is used in both normal and recovery
mode on reef.
Change-Id: Ie79737a1450bd1ff71543e44a5a3e16950e70fb3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17242
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
WACOM request to add a new identifier `WCOMNTN2`,
and use that for the board Pyro with all LCD combinations.
BRANCH=master
BUG=chrome-os-partner:58093
TEST=emerge-pyro vboot_reference coreboot chromeos-bootimage
Signed-off-by: Janice Li <janice.li@quantatw.com>
Change-Id: I95cf357efba958d7e864d2736d324e0aad70e307
Reviewed-on: https://review.coreboot.org/17257
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Increase the IRQ timeout to prevent issues if there is a delay
in the TPM responding to a command. Split the no-IRQ case out
so it doesn't suffer unnecessarily.
BUG=chrome-os-partner:59191
TEST=suspend/resume testing on eve board
Change-Id: I1ea7859bc7a056a450b2b0ee32153ae43ee8699f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17204
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
All current implementations of ramstage_cache_invalid() were just
resetting the system based on the RESET_ON_INVALID_RAMSTAGE_CACHE
Kconfig option. Move that behavior to a single implementation
within prog_loaders.c which removes duplication.
Change-Id: I67aae73f9e1305732f90d947fe57c5aaf66ada9e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17184
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add config in fsp 2.0/1.1 driver to reset if ramstage stage cache is
invalid during S3 resume.
Change-Id: I83fe76957c061f20e9afb308e55923806fda4f93
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17112
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=chrome-os-partner:57846
Change-Id: Id6bd91b3fd6420994ad5811d362618b1a38a8afa
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17092
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
1. Export i2c_generic_fill_ssdt to allow other device-specific i2c
drivers to share and re-use the same code for generating AML code for
SSDT. In order to achieve this, following changes are required:
a. Add macro I2C_GENERIC_CONFIG that defines a structure with all
generic i2c device-tree properties. This macro should be placed by the
using driver at the start of its config structure.
b. Accept a callback function to add any device specific information to
SSDT. If generic driver is used directly by a device, callback would be
NULL. Other devices using a separate i2c driver can provide a callback
to add any properties to SSDT.
2. Allow device to provide _CID.
BUG=chrome-os-partner:57846
Change-Id: I3a0054e22b81f9d6d407bef417eae5e9edc04ee4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17089
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add support to allow a device to define PowerResource in its SSDT AML
code. PowerResouce ACPI generation expects SoC to define the
callbacks for generating AML code for GPIO manipulation.
Device requiring PowerResource needs to define following parameters:
1. Reset GPIO - Optional, GPIO to put device into reset or take it out
of reset.
2. Reset delay - Delay after reset GPIO is de-asserted (default 0).
3. Enable GPIO - Optional, GPIO to enabled device.
4. Enable delay - Delay after enable GPIO is asserted (default 0).
BUG=chrome-os-partner:55988
Change-Id: Ieb2dd95fc1f555f5de66f3dda425172ac5b75dad
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17081
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Return config->name if it is not NULL.
BUG=chrome-os-partner:55988
Change-Id: I9ae229949b73de6f991383daae8d962d6cf457a7
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17077
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
When compiling a non-x86 platform with DRIVERS_INTEL_WIFI enabled,
we get the build error:
src/drivers/intel/wifi/wifi.c:17:30: fatal error:
arch/acpi_device.h: No such file or directory
acpi_device.h only exists in the x86 architecture directory.
Change-Id: Id0e29558336bf44e638cfcb97c22f31683ea4ec7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16906
Tested-by: build bot (Jenkins)
Reviewed-by: Antonello Dettori <dev@dettori.io>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
|
|
This patch enables stage cache to save ~40ms during S3 resume.
It saves ramstage in the stage cache and restores it on resume
so that ramstage does not have to reinitialize during the
resume flow. Stage cache functionality is added to postcar stage
since ramstage is called from postcar.
BUG=chrome-os-partner:56941
BRANCH=none
TEST=built for Reef and tested ramstage being cached
Change-Id: I1551fd0faca536bd8c8656f0a8ec7f900aae1f72
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/16833
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: If79eb706b6d44f7c34dfe31a1545f5850870b334
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16866
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Instead of hard-coding the polarity of the GPIO to active high/low,
accept it as a parameter in devicetree. This polarity can then be used
while calling into acpi_dp_add_gpio to determine the active low status
correctly.
BUG=chrome-os-partner:55988
BRANCH=None
TEST=Verified that correct polarity is set for reset-gpio on reef.
Change-Id: I4aba4bb8bd61799962deaaa11307c0c5be112919
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/16877
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
UX Doc = go/gale-hw-ui
This color wasn't changed earlier as the change wasn't done in
the OS also. However, since we cannot change this later in FW
(but OS can change anytime), I am making this change after discussing
with the UX team.
BUG=b:31501528, b:31633562
TEST=Change the device state to 'recovery mode' to observe the new
color.
BRANCH=none
Change-Id: Ia91f14eb77492095cb41a9de0bb9790e72aa4851
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 36a3d8c6eabbc0b23d0a15d5bddc5ed3bdeebe70
Original-Change-Id: I88768b94cf91804a6005e44b1a168e059698ec4b
Original-Signed-off-by: Suresh Rajashekara <sureshraj@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/388206
Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org>
Original-Tested-by: Suresh Rajashekara <sureshraj@chromium.org>
Original-Reviewed-by: Christopher Book <cbook@chromium.org>
Original-Reviewed-by: Kan Yan <kyan@google.com>
Reviewed-on: https://review.coreboot.org/16767
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Colors and patterns as defined by the UX team
BUG=b:31501528
TEST=Move the device to different states in FW using rec and dev
button and verify the colors
BRANCH=None
Change-Id: I66d41a54590cd3ce4e5202c7cfa890f462fe195e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 703559d5dddaeeb7d435d6cadbb2009a1b7a76c8
Original-Change-Id: I95ab1fa59b483396ff1498a28f1ee98ac08d02d7
Original-Signed-off-by: Suresh Rajashekara <sureshraj@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/387258
Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org>
Original-Tested-by: Suresh Rajashekara <sureshraj@chromium.org>
Original-Reviewed-by: Christopher Book <cbook@chromium.org>
Original-Reviewed-by: Kan Yan <kyan@google.com>
Reviewed-on: https://review.coreboot.org/16718
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
SPI read speed directly impacts boot time and we do quite a lot of
reading.
Add a way to easily find out the speed of SPI flash reads within
coreboot.
Write speed is less important since there are very few writes and they
are small.
BUG=chrome-os-partner:56556
BRANCH=none
TEST=run on gru with SPI_SPEED_DEBUG set to 1. See the output messages:
read SPI 627d4 7d73: 18455 us, 1740 KB/s, 13.920 Mbps
Change-Id: Id3814bd2b7bd045cdfcc67eb1fabc861bf9ed3b2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 82cb93f6be47efce3b0a3843bab89d2381baef89
Original-Change-Id: Iec66f5b8e3ad62f14d836a538dc7801e4ca669e7
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/376944
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16701
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Gale EVT3 has only one LED controller (earlier we had 2).
Remove the support for the second controller and also the
corresponding microcode. The color values used are the same
as onHub (Arkham to be specific).
BUG=b:30890905
TEST=Move the device to different states manually by appropriate
actions (like dev mode, rec mode etc) and observe the different
colors.
BRANCH=None
Change-Id: I853035610ea7ea7c8d29c30d2de13c9e2e786b2b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 593905d2d69daa7482318aa5f5c5cd7cf984043e
Original-Change-Id: If8f22abd605faac6f6215ef600041740ce15ea0c
Original-Signed-off-by: Suresh Rajashekara <sureshraj@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/370821
Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org>
Original-Tested-by: Suresh Rajashekara <sureshraj@chromium.org>
Original-Reviewed-by: Kan Yan <kyan@google.com>
Reviewed-on: https://review.coreboot.org/16697
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Move the setup of the IRQ status handler so it will be set up properly
before the early probe happens.
BUG=chrome-os-partner:53336
Change-Id: I4380af1233d2a252899459635a3cb69ca196088d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16861
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
|
|
Kconfig hex values don't need to be in quotes, and should start with
'0x'. If the default value isn't set this way, Kconfig will add the
0x to the start, and the entry can be added unnecessarily to the
defconfig since it's "different" than what was set by the default.
A check for this has been added to the Kconfig lint tool.
Change-Id: I86f37340682771700011b6285e4b4af41b7e9968
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16834
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Because these variables had "non-hexidecimal" defaults, they
were updated by kconfig when writing defconfig files.
Change-Id: Ic1a070d340708f989157ad18ddc79de7bb92d873
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16827
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
A copy of our uart8250io driver sneaked in with Broadwell-DE support.
The only difference is the lack of initialization (due to FSP handling
that).
TEST=manually compared resulting object files
Change-Id: I09be10b76c76c1306ad2c8db8fb07794dde1b0f2
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/16786
Tested-by: build bot (Jenkins)
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Fix errors in debug display support.
BRANCH=none
BUG=None
TEST=Build FSP 2.0 (SEC/PEI core with all FSP debug on) and run on
Galileo Gen2
Change-Id: I2ece056d66dc8568a7b7206970f20368ec5bf147
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16809
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a config option to the generic I2C device driver to indicate to
the OS that this device should be probed before being added.
This can be used to provide ACPI device instantiations to devices that
may not actually exist on the board. For example, if multiple trackpad
vendors are supported on the same board they can both be described in
ACPI and the OS will probe the address and load the driver only if the
device responds to the probe at that address.
BUG=chrome-os-partner:57686
Change-Id: I22cffb4b15f25d97dfd37dc58bca315f57bafc59
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16742
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The VBT id string is 20 characters long.
If the string is shorter than 20 it needs spaces at the end.
This change is cosmetic as all strings were padded by hand.
Change-Id: Id6439f1d3dbd09319ee99ce9d15dbc3bcead1f53
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16739
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Support reading the ACPI GPE status (on x86) to determine when
the cr50 is ready to return response data or is done processing
written data. If the interrupt is not defined by Kconfig then
it will continue to use the safe delay.
This was tested with reef hardware and a modified cr50 image
that generates interrupts at the intended points.
BUG=chrome-os-partner:53336
Change-Id: Ic8f805159650c45382cacac8840450a1f8b4d7a1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16672
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Unify the function names to be consistent throughout the driver
and improve the handling while waiting for data available and
data expected flags from the TPM.
BUG=chrome-os-partner:53336
Change-Id: Ie2dfb7ede1bcda0e77070df945c47c1428115907
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16668
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Clean up the mask and timeout handling in the locality functions
that were copied from the original driver.
BUG=chrome-os-partner:53336
Change-Id: Ifdcb3be0036b2c02bfbd1bcd326e9519d3726ee0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16667
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Rename the low-level functions from iic_tpm_read/write to
cr50_i2c_read/write to better match the driver name, and pass in the
tpm_chip structure to the low-level read/write functions as it will
be needed in future changes.
BUG=chrome-os-partner:53336
Change-Id: I826a7f024f8d137453af86ba920e0a3a734f7349
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16666
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use two different timeouts in the driver. The 2ms timeout is needed
to be safe for cr50 to cover the extended timeout that is seen with
some commands. The other at 2 seconds which is a TPM spec timeout.
BUG=chrome-os-partner:53336
Change-Id: Ia396fc48b8fe6e56e7071db9d74561de02b5b50e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16665
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Reduce the static buffer size from the generic default 1260
down to 64 to match the max FIFO size for the cr50 hardware
and reduce the footprint of the driver.
BUG=chrome-os-partner:53336
Change-Id: I6f9f71d501b60299edad4b16cc553a85391a1866
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16664
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Originally I thought it would be cleaner to keep this code in one
place, but as things continue to diverge it ends up being easier
to split this into its own driver. This way the different drivers
in coreboot, depthcharge, and the kernel, can all be standalone
and if one is changed it is easier to modify the others.
This change splits out the cr50 driver and brings along the basic
elements from the existing driver with no real change in
functionality. The following commits will modify the code to make
it consistent so it can all be shared with depthcharge and the
linux kernel drivers.
BUG=chrome-os-partner:53336
Change-Id: I3b62b680773d23cc5a7d2217b9754c6c28bccfa7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16663
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Move the common enums and variables to tpm.h so it can be
used by multiple drivers.
BUG=chrome-os-partner:53336
Change-Id: Ie749f13562be753293448fee2c2d643797bf8049
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16662
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
These values are found in util/cbfstool/cbfs.h.
Change-Id: Iea4807b272c0309ac3283e5a3f5e135da6c5eb66
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16646
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This reverts commit 64df72e8e2d1c086705325533767ca5e201e842a.
|
|
This reverts commit c565f9910707b91fcc7a27bab28806e558bb474d.
|
|
This reverts commit 97a2a1ece152b6d40a524361721405b77c37959d.
|
|
This reverts commit 93c778688f0bf2f90334505a3082a2cd4ce1623a.
|
|
This reverts commit 6f5ceb26b9b3e1455ebbd6192e1d2c832bddc77e.
|
|
This reverts commit 557e1a729a9ca89e814220b6203b7ac0dc446913.
|
|
This reverts commit 1241e7db55aff313e56bf4546d969c11368b08a2.
|
|
This reverts commit a5e419c51187d24818f056327746a18676fe3a20.
|
|
Support reading the ACPI GPE status (on x86) to determine when
the cr50 is ready to return response data or is done processing
written data. If the interrupt is not defined by Kconfig then
it will continue to use the safe delay.
This was tested with reef hardware and a modified cr50 image
that generates interrupts at the intended points.
BUG=chrome-os-partner:53336
Change-Id: I9f78f520fd089cb4471d8826a8cfecff67398bf8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
|
