summaryrefslogtreecommitdiff
path: root/src/drivers/spi
AgeCommit message (Collapse)Author
2017-11-21spi/tpm: claim locality just once during bootVadim Bendebury
All coreboot stages using TPM start with the same sequence: check if locality is claimed, if so, release it by writing 'active locality' bit, then try claiming it. This is actually not a proper procedure: section "5.5.2.3.1 Command Aborts" of "TCG PC Client Platform TPM Profile (PTP) Specification Level 00 Revision 00.430 Family 2" lists overwriting active locality status bit as a means of triggering TPM command abort. On top of that, none of the coreboot stages releases locality, it is enough to claim it once when device starts booting. In fact, locality being active when the device is in verstage is most likely due to delayed TPM reset processing by the Cr50 TPM: reset is an asynchronous event, and is processed once current command processing completes. The proper procedure is to wait if locality is active until it is released (which will happen when Cr50 processes reset) and then proceed to claim it. This needs to happen only during verstage, other stages using TPM are guaranteed has been claimed earlier. BRANCH=gru BUG=b:65867313 TEST=the new autotest triggering EC reset during key generation process does not cause boot failures on Fizz device any more. Below are times verstage had to wait: TPM ready after 3132 ms TPM ready after 22120 ms TPM ready after 4936 ms TPM ready after 6445 ms TPM ready after 11798 ms TPM ready after 27421 ms TPM ready after 4582 ms TPM ready after 7532 ms TPM ready after 27920 ms TPM ready after 3539 ms TPM ready after 12557 ms TPM ready after 6773 ms TPM ready after 1631 ms TPM ready after 197 ms TPM ready after 24330 ms TPM ready after 3241 ms Change-Id: Iaee04f009bcde03712483e5e03de4a3441ea32b1 Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Reviewed-on: https://review.coreboot.org/22489 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-11-16drivers/spi/tpm: Poll TPM_VALID bit until validShelley Chen
In case the TPM is doing a long crypto operation the initial probe could be very delayed. Rather than end up in recovery make the delay long enough to accommodate the (current) long crypto times. This would add a maximum of 30 seconds to boot time. Mirroring changes done on i2c side in CL:756918 BUG=b:65867313, b:68729265 BRANCH=None TEST=Make sure fizz boots up Change-Id: Ie944bfb6fe33d6e9ee794439165716ab624be491 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/22370 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-11-01spi/tpm: Make sure AP properly syncs up with Cr50Vadim Bendebury
When Cr50 TPM is being reset, it continues replying to the SPI bus requests, sends wrong register values in response to read requests. This patch makes sure that the TPM driver does not proceed unless proper value is read from the TPM device identification register. If the read value is still wrong after 10 retries taken with 10 ms intervals, the driver gives up and declares TPM broken/unavailable. BRANCH=cr50 BUG=b:68012381 TEST=ran a script resetting the Fizz device as soon as the "index 0x1007 return code 0" string shows up in the AP console output. The script keeps rebooting the Fizz indefinitely, before this script Fizz would fail to read TPM properly and fall into recovery after no more than four reboots. Change-Id: I7e67ec62c2bf31077b9ae558e09214d07eccf96b Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Reviewed-on: https://review.coreboot.org/22231 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-16console/flashconsole: Enable support for postcarYouness Alaoui
If FSP 2.0 is used, then postcar stage is used and the flashconsole as well as spi drivers needed to be added. Change-Id: I46d720a9d1fe18a95c9407d08dae1eb70ae6720e Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Reviewed-on: https://review.coreboot.org/21959 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-09-14device: acpi_name() should take a const struct deviceAaron Durbin
There's no reason to mutate the struct device when determining the ACPI name for a device. Adjust the function pointer signature and the respective implementations to use const struct device. Change-Id: If5e1f4de36a53646616581b01f47c4e86822c42e Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/21527 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-08-30acpigen: Add stop gpio control to power resourceFurquan Shaikh
There is at least one I2C device (being used by Soraka) that has 3 controls -- enable, reset and stop. If the stop gpio is not put into the right state when turning off the device in suspend mode, then it causes leakage. Thus, we need control in power resource to be able to stop the device when entering suspend state. BUG=b:64987428 TEST=Verified on soraka that touchscreen stop is correctly configured on suspend. Change-Id: Iae5ec7eb3972c5c7f80956d60d0d3c321bbefb0f Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/21249 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-07-02drivers/spi: add IS_ENABLED() around Kconfig symbol referencesMartin Roth
Some of these can be changed from #if to if(), but that will happen in a follow-on commmit. Change-Id: If80e0c4e1c9911b44853561b03aef1c741255229 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/20339 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-06-27drivers/spi: Don't disable non-existent warnings on clangStefan Reinauer
The warning -Wstack-usage= doesn't seem to exist on clang, so trying to disable it makes the compiler unhappy about non-existent pragmas. Catching this on gcc is good enough, so let's disable it for the clang case Change-Id: Ia3716a83ba41743ac1dbe73e70abd170de30d7ab Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-on: https://review.coreboot.org/20383 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2017-06-04console/flashsconsole: Add spi flash console for debuggingYouness Alaoui
If CONSOLE_SPI_FLASH config is enabled, we write the cbmem messages to the 'CONSOLE' area in FMAP which allows us to grab the log when we read the flash. This is useful when you don't have usb debugging, and UART lines are hard to find. Since a failure to boot would require a hardware flasher anyways, we can get the log at the same time. This feature should only be used when no alternative is found and only when we can't boot the system, because excessive writes to the flash is not recommended. This has been tested on purism/librem13 v2 and librem 15 v3 which run Intel Skylake hardware. It has not been tested on other archs or with a driver other than the fast_spi. Change-Id: I74a297b94f6881d8c27cbe5168f161d8331c3df3 Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Reviewed-on: https://review.coreboot.org/19849 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
2017-05-24drivers/spi/spi-generic: Make spi_setup_slave strong symbolFurquan Shaikh
Now that all platforms are updated to provide spi bus map, there is no need to keep the spi_setup_slave as a weak symbol. BUG=b:38430839 Change-Id: I59b9bbb5303dad7ce062958a0ab8dee49a4ec1e0 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19781 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-05-19drivers/spi/spi_flash: Move flash ops to spi_flash_ops structureFurquan Shaikh
Define a new spi_flash_ops structure, move all spi flash operations to this structure and add a pointer to this structure in struct spi_flash. BUG=b:38330715 Change-Id: I550cc4556fc4b63ebc174a7e2fde42251fe56052 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19757 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-05-19drivers/spi/spi_flash: Clean up SPI flash probeFurquan Shaikh
1. Rename __spi_flash_probe to spi_flash_generic_probe and export it so that drivers can use it outside spi_flash.c. 2. Make southbridge intel spi driver use spi_flash_generic_probe if spi_is_multichip returns 0. 3. Add spi_flash_probe to spi_ctrlr structure to allow platforms to provide specialized probe functions. With this change, the specialized spi flash probe functions are now associated with a particular spi ctrlr structure and no longer disconnected from the spi controller. BUG=b:38330715 Change-Id: I35f3bd8ddc5e71515df3ef0c1c4b1a68ee56bf4b Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19708 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2017-05-19drivers/spi/spi_flash: Pass in spi_slave structure as const to probe functionsFurquan Shaikh
Pointer to spi_slave structure can be passed in as const to spi flash probe functions since the probe functions do not need to modify the slave properties. BUG=b:38330715 Change-Id: I956ee777c62dbb811fd6ce2aeb6ae090e1892acd Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19707 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-05-19drivers/spi/spi_flash_internal: Remove unused spi_fram_probe_ramtronFurquan Shaikh
Remove unused function declaration spi_fram_probe_ramtron. BUG=b:38330715 Change-Id: I05e6c5c2b97d6c8a726c0e443ad855f9bcb703f9 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19706 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-05-19drivers/spi/spi_flash: Pass in flash structure to fill in probeFurquan Shaikh
Instead of making all SPI drivers allocate space for a spi_flash structure and fill it in, udpate the API to allow callers to pass in a spi_flash structure that can be filled by the flash drivers as required. This also cleans up the interface so that the callers can maintain and free the space for spi_flash structure as required. BUG=b:38330715 Change-Id: If6f1b403731466525c4690777d9b32ce778eb563 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19705 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-05-19drivers/spi/spi_flash: Add page_size to struct spi_flashFurquan Shaikh
Add a new member page_size to spi_flash structure so that the various spi flash drivers can store this info in spi_flash along with the other sizes (sector size and total size) during flash probe. This removes the need to have {driver}_spi_flash structure in every spi flash driver. This is part of patch series to clean up the SPI flash and SPI driver interface. BUG=b:38330715 Change-Id: I0f83e52cb1041432b0b575a8ee3bd173cc038d1f Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19704 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-05-19drivers/spi/spi_flash: Use boot_device_spi_flash to obtain spi_flash structureFurquan Shaikh
Instead of storing spi flash device structure in spi flash driver, use boot_device_spi_flash callback to obtain pointer to boot device spi flash structure. BUG=b:38330715 Change-Id: Idd50b7644d1a4be8b62d38cc9239feae2215103c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19703 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-05-19drivers/spi/cbfs_spi: Provide implementation of boot_device_spi_flashFurquan Shaikh
This allows callers to retrieve handle to the boot device spi_flash structure. BUG=b:38330715 Change-Id: I1c07327115e0449cbd84d163218da76a6fa2cea0 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19726 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-05-05drivers/spi: Re-factor spi_crop_chunkFurquan Shaikh
spi_crop_chunk is a property of the SPI controller since it depends upon the maximum transfer size that is supported by the controller. Also, it is possible to implement this within spi-generic layer by obtaining following parameters from the controller: 1. max_xfer_size: Maximum transfer size supported by the controller (Size of 0 indicates invalid size, and unlimited transfer size is indicated by UINT32_MAX.) 2. deduct_cmd_len: Whether cmd_len needs to be deducted from the max_xfer_size to determine max data size that can be transferred. (This is used by the amd boards.) Change-Id: I81c199413f879c664682088e93bfa3f91c6a46e5 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19386 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Tested-by: coreboot org <coreboot.org@gmail.com>
2017-04-24drivers/spi/tpm: Do not let MAINBOARD_HAS_SPI_TPM_CR50 depend on SPI_TPMDaniel Kurtz
MAINBOARD_HAS_SPI_TPM_CR50 describes a capability of the board and SPI_TPM is only on if we actually want to compile in the TPM code. For example, in src/drivers/i2c/tpm/Kconfig MAINBOARD_HAS_I2C_TPM_CR50 also doesn't depend on SPI_TPM. This problem manifests itself as the following build issue when building with MAINBOARD_HAS_I2C_TPM_CR50 but without an explict "select TPM2": src/Kconfig:296:error: recursive dependency detected! src/Kconfig:296: symbol MAINBOARD_HAS_TPM2 is selected by MAINBOARD_HAS_TPM_CR50 src/Kconfig:408: symbol MAINBOARD_HAS_TPM_CR50 depends on MAINBOARD_HAS_SPI_TPM_CR50 src/drivers/spi/tpm/Kconfig:15: symbol MAINBOARD_HAS_SPI_TPM_CR50 depends on SPI_TPM src/drivers/spi/tpm/Kconfig:1: symbol SPI_TPM depends on TPM2 src/Kconfig:396: symbol TPM2 is selected by MAINBOARD_HAS_TPM2 MAINBOARD_HAS_SPI_TPM_CR50 shouldn't depend on SPI_TPM. BRANCH=none BUG=b:36786804 TEST=Boot rowan w/ serial enabled, verify coreboot and depthcharge are configured to use IRQ flow control when talking to the Cr50 TPM. Change-Id: I0cb3f6d3aa4159bad563a6a4b006d7f4825e04b4 Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Suggested-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/19411 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-04-24drivers/spi/spiconsole: Fix broken spiconsole driverFurquan Shaikh
Use spi_setup_slave to fill up the spi_slave structure with pointer to spi_ctrlr structure which can then be used to perform all spi operations. Change-Id: I2804ed1e85402426a654352e1ceaf0993546cd8b Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19385 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
2017-04-13drivers/spi/tpm: Clean up SPI TPM driverFurquan Shaikh
1. Move common TIS macros to include/tpm.h. 2. Use common TIS macros while referring to status and access registers. 3. Add a new function claim_locality to properly check for required access bits and claim locality 0. BUG=b:36873582 Change-Id: I11bf3e8b6e1f50b7868c9fe4394a858488367287 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19213 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-04-09drivers/spi: Get rid of spi_get_configFurquan Shaikh
There is only one user for spi_get_config i.e. SPI ACPI. Also, the values provided by spi_get_config are constant for now. Thus, get rid of the spi_get_config call and fill in these constant values in SPI ACPI code itself. If there is a need in the future to change these, appropriate device-tree configs can be added. BUG=b:36873582 Change-Id: Ied38e2670784ee3317bb12e542666c224bd9e819 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19203 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-04-05drivers/spi/tpm: Allow TPM_SPI to be used with PC80_SYSTEM.Furquan Shaikh
In order to be able to use SPI TPM on x86, allow TPM_SPI to be used with PC80_SYSTEM. BUG=b:35583330 Change-Id: Ibe626a192d45cf2624368db42d369202a4003123 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19093 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-04-05drivers/spi/tpm: Make SPI TPM driver CAR-safeFurquan Shaikh
1. Use proper CAR semantics for global/static variables. 2. Use spi_* functions directly instead of using a global structure to store pointers to those functions. BUG=b:36873582 Change-Id: I1fc52ab797ef0cbd3793a387d68198efc5dde58c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19114 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-04-05drivers/spi/tpm: using tpm irq to sync tpm transactionJeffy Chen
BUG=b:35647967 TEST=boot from bob Change-Id: Ib64107b17fb6e93dbe626ce92f3bc9da8b84784e Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Reviewed-on: https://chromium-review.googlesource.com/452284 Commit-Ready: Caesar Wang <wxt@rock-chips.com> Tested-by: Caesar Wang <wxt@rock-chips.com> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/19113 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-04-05drivers/spi/tpm: try to wake cr50 if it is asleepJeffy Chen
BUG=b:35775002 TEST=boot from bob Change-Id: I6324f3c02da55a8527f085ba463cbb1f4fb5dc2e Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Reviewed-on: https://chromium-review.googlesource.com/452283 Commit-Ready: Caesar Wang <wxt@rock-chips.com> Tested-by: Caesar Wang <wxt@rock-chips.com> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/19112 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-04-05drivers/spi/tpm: Add tis.c and tpm.c to ramstage and romstageFurquan Shaikh
These files are required to support recovery MRC cache hash save/restore in romtage/ramstage. BUG=b:35583330 Change-Id: Idd0a4ee1c5f8f861caf40d841053b83a9d7aaef8 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19092 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-04-03drivers/spi/tpm: honor tis_sendrecv() APIAaron Durbin
The spi tis_sendrecv() implementation was always returning success for all transactions. Correct this by returning -1 on error when tpm2_process_command() returns 0 since that's its current failure return code. BUG=b:36598499 Change-Id: I8bfb5a09198ae4c293330e770271773a185d5061 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/19058 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2017-04-03drivers/spi/tpm: make tpm_info object local to compilation unitAaron Durbin
The tpm_info object is a global, but its symbol does not need to be exposed to the world as its only used within tpm.c. BUG=b:36598499 Change-Id: Idded3dad8d0d1c3535bddfb359009210d3439703 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/19057 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2017-04-03drivers/spi/tpm: de-assert chip select on transaction errorAaron Durbin
In the case of start_transaction() failing the chip select is never deasserted. Correct that by deasserting the chip select when start_transaction() fails. BUG=b:36598499 Change-Id: I2c5200085eb357259edab39c1a0fa7b1d81ba7b2 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/19056 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-03-09drivers/spi/tpm: provide Kconfig to indicate CR50 usageAaron Durbin
Going forward it's important to note when a CR50 is expected to be present in the system. Additionally, this Kconfig addition provides symmetry with the equivalent i2c Kconfig option. BUG=b:35775104 Change-Id: Ifbd42b8a22f407534b23459713558c77cde6935d Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/18680 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2017-02-19drivers/spi/acpi: Add additional generic ACPI supportDuncan Laurie
Add support for more ACPI features in the generic SPI ACPI driver so it can be flexible enough to support more devices, or devices in different configurations. - add a wake pin - add support for using IRQ GPIO instead of PIRQ - add power resource support with enable and reset gpios BUG=chrome-os-partner:61233 TEST=ensure existing SSDT generation is unchanged, and test that new features generate expected code Change-Id: Ibe37cc87e488004baa2c08a369f73c86e6cd6dce Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18393 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-16drivers/spi: Add support for generating SPI device in SSDTFurquan Shaikh
Similar to I2C driver, add support for generating SPI device and required properties in SSDT for ACPI. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles succesfully. Verified SPI device generated in SSDT on poppy. Change-Id: Ic4da79c823131d54d9eb3652b86f6e40fe643ab5 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18342 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-16spi: Add function callback to get configuration of SPI busFurquan Shaikh
Add a new callback to spi_ctrlr structure - get_config - to obtain configuration of SPI bus from the controller driver. Also, move common config definitions from acpi_device.h to spi-generic.h BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully Change-Id: I412c8c70167d18058a32041c2310bc1c884043ce Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18337 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-01-10SPI: Fix command-response behaviorKyösti Mälkki
Fix SPI flash ops regressions after commit: c2973d1 spi: Get rid of SPI_ATOMIC_SEQUENCING When spi_flash_cmd() is called with argument response==NULL, only send out command without reading back the response. Change-Id: I28a94f208b4a1983d45d69d46db41391e267891d Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/18082 Tested-by: build bot (Jenkins) Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com> Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2016-12-23spi: Get rid of SPI_ATOMIC_SEQUENCINGFurquan Shaikh
SPI_ATOMIC_SEQUENCING was added to accomodate spi flash controllers with the ability to perform tx and rx of flash command and response at the same time. Instead of introducing this notion at SPI flash driver layer, clean up the interface to SPI used by flash. Flash uses a command-response kind of communication. Thus, even though SPI is duplex, flash command needs to be sent out on SPI bus and then flash response should be received on the bus. Some specialized x86 flash controllers are capable of handling command and response in a single transaction. In order to support all the varied cases: 1. Add spi_xfer_vector that takes as input a vector of SPI operations and calls back into SPI controller driver to process these operations. 2. In order to accomodate flash command-response model, use two vectors while calling into spi_xfer_vector -- one with dout set to non-NULL(command) and other with din set to non-NULL(response). 3. For specialized SPI flash controllers combine two successive vectors if the transactions look like a command-response pair. 4. Provide helper functions for common cases like supporting only 2 vectors at a time, supporting n vectors at a time, default vector operation to cycle through all SPI op vectors one by one. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully Change-Id: I4c9e78c585ad95c40c0d5af078ff8251da286236 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17681 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-19drivers/spi: fix flash writes at page boundariesAaron Durbin
There was an assumption that all SPI controllers could consume a full page of data to write. However, that assumption doesn't hold when spi_crop_chunk() indicates sizes smaller than page size. If the requested offset isn't page aligned from the start then writes will fail corrupting data since a page boundary isn't honored. The spansion driver needed quite a bit more work to honor the spi_crop_chunk() result. It now mimics the other driver's code. Also, needed to add spi_crop_chunk() to marvell/bg4cd SoC to make google/cosmos build. SPI obviously doesn't work on that platform, but it fixes the build error. Change-Id: I93e24a5a717adcee45a017c164bd960f4592ad50 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/17910 Tested-by: build bot (Jenkins) Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-12-16tpm2: handle failures more gracefullyVadim Bendebury
When trying to bring up a device with a malfunctioning TPM2 chip, the driver currently gets stuck waiting for SPI flow control, causing bricked devices. This patch puts a 100 ms cap on the waiting time - this should be enough even for a longest NVRAM save operation which could be under way on the TPM device. BRANCH=gru BUG=chrome-os-partner:59807 TEST=with a matching change in depthcharge, now a gru with corrupted SPI TPM comes up to the recovery screen (it was not showing signs of life before this change). Change-Id: I63ef5dde8dddd9afeae91e396c157a1a37d47c80 Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Reviewed-on: https://review.coreboot.org/17898 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2016-12-08drivers/spi: provide a mechanism to obtain the SPI flash boot deviceAaron Durbin
The MRC cache wants to be able to access the SPI flash boot device. Allow an easy way to provide that so that there isn't duplicate spi_flash objects representing the same device. BUG=chrome-os-partner:56151 Change-Id: Iba92e8bb8a6060cdd327b10f5f8ec23ac61101e7 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/17715 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2016-12-07spi: Clean up SPI driver interfaceFurquan Shaikh
1. Add new structure spi_ctrlr_buses that allows platform to define a mapping from SPI controller to buses managed by the controller. 2. Provide weak implementations of spi_init and spi_setup_slave that will be used by platforms using the new interface. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully Change-Id: Ia6f47941b786299f4d823895898ffb1b36e02f73 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17561 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-06spi_flash: Make a deep copy of spi_slave structureFurquan Shaikh
Commit 36b81af (spi: Pass pointer to spi_slave structure in spi_setup_slave) changes the way spi_setup_slave handles the spi_slave structure. Instead of expecting spi controller drivers to maintain spi_slave structure in CAR_GLOBAL/data section, caller is expected to manage the spi_slave structure. This requires that spi_flash drivers maintain spi_slave structure and flash probe function needs to make a copy of the passed in spi_slave structure. This change fixes the regression on Lenovo X230 and other mainboards. Change-Id: I0ad971eecaf3bfe301e9f95badc043193cc27cab Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17728 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Iru Cai <mytbk920423@gmail.com>
2016-12-05spi: Define and use spi_ctrlr structureFurquan Shaikh
1. Define a new structure spi_ctrlr that allows platforms to define callbacks for spi operations (claim bus, release bus, transfer). 2. Add a new member (pointer to spi_ctrlr structure) in spi_slave structure which will be initialized by call to spi_setup_slave. 3. Define spi_claim_bus, spi_release_bus and spi_xfer in spi-generic.c which will make appropriate calls to ctrlr functions. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully Change-Id: Icb2326e3aab1e8f4bef53f553f82b3836358c55e Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17684 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-05spi: Pass pointer to spi_slave structure in spi_setup_slaveFurquan Shaikh
For spi_setup_slave, instead of making the platform driver return a pointer to spi_slave structure, pass in a structure pointer that can be filled in by the driver as required. This removes the need for platform drivers to maintain a slave structure in data/CAR section. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully Change-Id: Ia15a4f88ef4dcfdf616bb1c22261e7cb642a7573 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17683 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-05spi: Fix parameter types for spi functionsFurquan Shaikh
1. Use size_t instead of unsigned int for bytes_out and bytes_in. 2. Use const attribute for spi_slave structure passed into xfer, claim bus and release bus functions. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully Change-Id: Ie70b3520b51c42d750f907892545510c6058f85a Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17682 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-11-22spi: Get rid of flash_programmer_probe in spi_slave structureFurquan Shaikh
flash_programmer_probe is a property of the spi flash driver and does not belong in the spi_slave structure. Thus, make spi_flash_programmer_probe a callback from the spi_flash_probe function. Logic still remains the same as before (order matters): 1. Try spi_flash_programmer_probe without force option 2. Try generic flash probing 3. Try spi_flash_programmer_probe with force option If none of the above steps work, fail probing. Flash controller is expected to honor force option to decide whether to perform specialized probing or to defer to generic probing. BUG=None BRANCH=None TEST=Compiles successfully Change-Id: I4163593eea034fa044ec2216e56d0ea3fbc86c7d Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17465 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-11-22spi: Get rid of max_transfer_size parameter in spi_slave structureFurquan Shaikh
max_transfer_size is a property of the SPI controller and not of the spi slave. Also, this is used only on one SoC currently. There is no need to handle this at the spi flash layer. This change moves the handling of max_transfer_size to SoC SPI driver and gets rid of the max_transfer_size parameter. BUG=None BRANCH=None TEST=Compiles successfully. Change-Id: I19a1d0a83395a58c2bc1614b24518a3220945a60 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17463 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins)
2016-11-22spi: Clean up SPI flash driver interfaceFurquan Shaikh
RW flag was added to spi_slave structure to get around a requirement on some AMD flash controllers that need to group together all spi volatile operations (write/erase). This rw flag is not a property or attribute of the SPI slave or controller. Thus, instead of saving it in spi_slave structure, clean up the SPI flash driver interface. This allows chipsets/mainboards (that require volatile operations to be grouped) to indicate beginning and end of such grouped operations. New user APIs are added to allow users to perform probe, read, write, erase, volatile group begin and end operations. Callbacks defined in spi_flash structure are expected to be used only by the SPI flash driver. Any chipset that requires grouping of volatile operations can select the newly added Kconfig option SPI_FLASH_HAS_VOLATILE_GROUP and define callbacks for chipset_volatile_group_{begin,end}. spi_claim_bus/spi_release_bus calls have been removed from the SPI flash chip drivers which end up calling do_spi_flash_cmd since it already has required calls for claiming and releasing SPI bus before performing a read/write operation. BUG=None BRANCH=None TEST=Compiles successfully. Change-Id: Idfc052e82ec15b6c9fa874cee7a61bd06e923fbf Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17462 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-10-06spi: Add a way to show SPI transfer speed for readsSimon Glass
SPI read speed directly impacts boot time and we do quite a lot of reading. Add a way to easily find out the speed of SPI flash reads within coreboot. Write speed is less important since there are very few writes and they are small. BUG=chrome-os-partner:56556 BRANCH=none TEST=run on gru with SPI_SPEED_DEBUG set to 1. See the output messages: read SPI 627d4 7d73: 18455 us, 1740 KB/s, 13.920 Mbps Change-Id: Id3814bd2b7bd045cdfcc67eb1fabc861bf9ed3b2 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 82cb93f6be47efce3b0a3843bab89d2381baef89 Original-Change-Id: Iec66f5b8e3ad62f14d836a538dc7801e4ca669e7 Original-Signed-off-by: Simon Glass <sjg@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/376944 Original-Commit-Ready: Julius Werner <jwerner@chromium.org> Original-Tested-by: Simon Glass <sjg@google.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16701 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-02Kconfig: Update default hex values to start with 0xMartin Roth
Kconfig hex values don't need to be in quotes, and should start with '0x'. If the default value isn't set this way, Kconfig will add the 0x to the start, and the entry can be added unnecessarily to the defconfig since it's "different" than what was set by the default. A check for this has been added to the Kconfig lint tool. Change-Id: I86f37340682771700011b6285e4b4af41b7e9968 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16834 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-08-24drivers/spi: remove unconditional RW boot device initializationAaron Durbin
The SPI drivers for the various chipsets are not consistent in their handling of when they are accessible. Coupled with the unknown ordering of boot_device_init() being called this can lead to unexpected behavior (probing failures or hangs). Instead move the act of initializing the SPI flash boot device to when the various infrastructure requires its usage when it calls boot_device_rw(). Those platforms utilizing the RW boot device would need to ensure their SPI drivers are functional and ready when the call happens. This further removes any other systems failing to boot as reported in https://ticket.coreboot.org/issues/67. BUG=chrome-os-partner:56151 Change-Id: Ib3bddf5e26bf5322f3dd20345eeef6bee40f0f66 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16300 Tested-by: build bot (Jenkins) Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2016-08-23drivers/spi: be sure to call spi_init() before spi_flash_probe()Aaron Durbin
It's necessary to call spi_init() prior to calling spi_flash_probe() such that the SPI drivers can do any work required prior to performing SPI transactions. It could be argued that the drivers should handle such situations, however the SPI API implementations seem to assume the callers ensured spi_init() was called before any SPI transactions. This fixes systems that failed to boot introduced by [1]. Issue tracked in https://ticket.coreboot.org/issues/67. [1] I2aa75f88409309e3f9b9bd79b52d27c0061139c8 https://review.coreboot.org/16200 BUG=chrome-os-partner:56151 Change-Id: I2d8d5ac685833521f1efe212b07a4b61ba0d9bc3 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16297 Tested-by: build bot (Jenkins) Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
2016-08-19drivers/spi: provide optional implementation of boot_device_rw()Aaron Durbin
On many x86 platforms the boot device is SPI which is memory mapped. However, in order to write to the boot device one needs to use the SPI api. Therefore, provide a common implementation of boot_device_rw() which has no mmap() functionality. It only reads, writes, and erases. This will be used in the existing infrastructure but in a SPI agnostic way. Two options are added: 1. BOOT_DEVICE_SPI_FLASH_RW_NOMMAP 2. BOOT_DEVICE_SPI_FLASH_RW_NOMMAP_EARLY The former is auto-selected when COMMON_CBFS_SPI_WRAPPER is not selected. The latter can be used to include the implementation in the early stages such as bootblock, verstage, and romstage. BUG=chrome-os-partner:56151 Change-Id: I2aa75f88409309e3f9b9bd79b52d27c0061139c8 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16200 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2016-08-19drivers/spi: include SPI flash modules for all stagesAaron Durbin
It shouldn't matter if COMMON_CBFS_SPI_WRAPPER is selected to include the SPI flash support in all stages. Therefore, include the SPI flash support files in all the stages. While there include the same set of files for all stages. They were out of sync for some reason. BUG=chrome-os-partner:56151 Change-Id: I933335104203315cbbcf965185a7c176974e6356 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16198 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-08-19drivers/spi: ensure SPI flash is boot device for coreboot tablesAaron Durbin
The spi_flash_probe() routine was setting a global varible unconditonally regardless if the probe was for the boot device or even if the boot devcie was flash. Moreover, there's no need to report the SPI information if the boot device isn't even SPI. Lastly, it's possible that the boot device is a SPI flash, but the platform may never probe (selecting SPI_FLASH) for the actual device connected. In that situation don't fill anything in as no correct information is known. BUG=chrome-os-partner:56151 Change-Id: Ib0eba601df4d77bede313c358c92b0536355bbd0 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16197 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2016-08-19lib/cbfs_spi: provide boot_device_rw() supportAaron Durbin
Provide the RW boot device operations for the common cbfs SPI wrapper. The RW region_device is the same as the read-only one. As noted in the boot_device_rw() introduction patch the mmap() support should not be used in conjuction with writing as that results in incoherent operations. That's fine as the current mmap() support is only used in the cbfs layer which does not support writing, i.e. no cbfs regions would be written to with any previous or outstanding mmap() calls. BUG=chrome-os-partner:56151 Change-Id: I7cc7309a68ad23b30208ac961b1999a79626b307 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16199 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2016-08-19Kconfig: introduce writable boot device notionAaron Durbin
Indicate to the build system that a platform provides support for a writable boot device. The following will provide the necessary support: COMMON_CBFS_SPI_WRAPPER users soc/intel/apollolake soc/intel/baytrail soc/intel/braswell soc/intel/broadwell soc/intel/skylake The SPI_FLASH option is auto-selected if the platform provides write supoprt for the boot device and SPI flash is the boot device. Other platforms may provide similar support, but they do that in a device specific manner such as selecting SPI_FLASH explicitly. This provides clearance against build failures where chipsets don't provide SPI API implementations even though the platform may use a SPI flash to boot. BUG=chrome-os-partner:56151 Change-Id: If78160f231c8312a313f9b9753607d044345d274 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16211 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-08-19drivers/spi: move cbfs_spi.c locationAaron Durbin
The common boot device spi implementation is very much specific to SPI flash. As such it should be moved into that subdirectory. It's still a high-level option but it correctly depends on BOOT_DEVICE_SPI_FLASH. Additionally that allows the auto-selection of SPI_FLASH by a platform selecting COMMON_CBFS_SPI_WRAPPER which allows for culling of SPI_FLASH selections everywhere. BUG=chrome-os-partner:56151 Change-Id: Ia2ccfdc9e1a4348cd91b381f9712d8853b7d2a79 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16212 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-08-19Kconfig: separate memory mapped boot device from SPIAaron Durbin
Make the indication of the boot device being memory mapped separate from SPI. However, retain the same defaults that previously existed. BUG=chrome-os-partner:56151 Change-Id: I06f138078c47a1e4b4b3edbdbf662f171e11c9d4 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16228 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2016-08-19tpm2: Fixed typoRobert Foss
Fixed "intierface" typo. Change-Id: I65f0156ee059a8bed96c900ca3da3a06f45901e8 Signed-off-by: Robert Foss <robert.foss@collabora.com> Reviewed-on: https://review.coreboot.org/16252 Tested-by: build bot (Jenkins) Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
2016-08-18Kconfig: rename BOOT_MEDIA_SPI_BUS to BOOT_DEVICE_SPI_FLASH_BUSAaron Durbin
Provide a default value of 0 in drivers/spi as there weren't default values aside from specific mainboards and arch/x86. Remove any default 0 values while noting to keep the option's default to 0. BUG=chrome-os-partner:56151 Change-Id: If9ef585e011a46b5cd152a03e41d545b36355a61 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16192 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2016-08-18Kconfig: lay groundwork for not assuming SPI flash boot deviceAaron Durbin
Almost all boards and chipsets within the codebase assume or use SPI flash as the boot device. Therefore, provide an option for the boards/chipsets which don't currently support SPI flash as the boot device. The default is to assume SPI flash is the boot device unless otherwise instructed. This falls in line with the current assumptions, but it also allows one to differentiate a platform desiring SPI flash support while it not being the actual boot device. One thing to note is that while google/daisy does boot with SPI flash part no SPI API interfaces were ever implemented. Therefore, mark that board as not having a SPI boot device. BUG=chrome-os-partner:56151 Change-Id: Id4e0b4ec5e440e41421fbb6d0ca2be4185b62a6e Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16191 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2016-08-15Revert "Kconfig: separate memory mapped boot device from SPI"Aaron Durbin
This reverts commit a83bbf58541cf41ea7a97dedbc8c02dffa59e86d. This was submitted out of order. Change-Id: Ic5a28faf94c1f1901a72e46343722eb4224c5086 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16226 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Nico Huber <nico.h@gmx.de>
2016-08-15drivers/spi: provide option to not include all flash driversAaron Durbin
All flash drivers are automatically included in the build unless COMMON_CBFS_SPI_WRAPPER was selected. However, there are cases where these drivers are unnecessary such as certain intel platforms where spi controller uses hardware sequencing without any ability to manually probe the device. Therefore, provide an option that the SoC can set the default value for. The COMMON_CBFS_SPI_WRAPPER option is still honored by not including all drivers when that is selected. BUG=chrome-os-partner:56151 Change-Id: Ie9aa447da450f7c8717545f05cff800139a9e2dd Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16187 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Vadim Bendebury <vbendeb@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-08-15Kconfig: separate memory mapped boot device from SPIAaron Durbin
Make the indication of the boot device being memory mapped separate from SPI. However, retain the same defaults that previously existed. BUG=chrome-os-partner:56151 Change-Id: Ibdd7c8754f9bf560a878136b1f55238e2c2549d3 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16193 Reviewed-by: Andrey Petrov <andrey.petrov@intel.com> Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-08-05drivers/spi: Add support for Micron N25Q128AWerner Zeh
Although we have already support for the flash chip N25Q128 there is a similar type available which has the same geometry and opcodes but unfortunately a slightly different device type ID. While the already supported N25Q128 has the ID 0xbb18 this one has the ID 0xba18. To make both types available in the flash support table, use N25Q128A as the flash name. This name can be found in the datasheet which can be found here: https://www.micron.com/~/media/documents/products/data-sheet/nor-flash/serial-nor/n25q/n25q_128mb_3v_65nm.pdf TEST=Booted and verified that MRC cache could be written Change-Id: I02a47692efb23a9a06a289c367488abd256b8e0c Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/16061 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2016-08-03spi/tpm: read TPM version in larger chunksVadim Bendebury
The TPM version string has become much longer recently, and the TPM_FW_VER register available on VID 1ae0 devices supports reading in arbitrary size quantities. Let's read 50 bytes at a time to reduce the SPI register read wrapper overhead, and increase the length limit to 300 bytes to accommodate longer version strings. TEST=verified on the Kevin device: localhost ~ # grep cr50 /sys/firmware/log Firmware version: RO_A: 0.0.1/84e2dde7 RO_B:* 0.0.2/13eda43f RW_A:* cr50_v1.1.5005-444ddb7 RW_B: cr50_v1.1.5005-5aac83c cr50_v1.1.5005-444ddb7 private-cr51:v0.0.66-bd9a0fe tpm2:v0.0.259-8f3d735 cryptoc:v0.0.4-5319e83 2016-07-31 10:58:05 vbendeb@kvasha Change-Id: Ifaf28c1a9a3990372a9cec108c098edbe50d3243 Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Reviewed-on: https://review.coreboot.org/16000 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-08-01Add newlines at the end of all coreboot filesMartin Roth
Change-Id: I7930d5cded290f2605d0c92a9c465a3f0c1291a2 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/15974 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-07-31Remove extra newlines from the end of all coreboot files.Martin Roth
This removes the newlines from all files found by the new int-015-final-newlines script. Change-Id: I65b6d5b403fe3fa30b7ac11958cc0f9880704ed7 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/15975 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-07-12tpm: report firmware versionVadim Bendebury
Some devices allow to retrieve firmware version by reading the same 4 byte register repeatedly until the entire version string is read. Let's print out TPM firmware version when available. Just in case something goes wrong limit the version string length to 200 bytes. CQ-DEPEND=CL:355701 BRANCH=none BUG=chrome-os-partner:54723 TEST=built the new firmware and ran it on Gru, observed the following in the coreboot console log: Connected to device vid:did:rid of 1ae0:0028:00 Firmware version: cr50_v1.1.4792-7a44484 Original-Commit-Id: 1f54a30cebe808abf1b09478b47924bb722a0ca6 Original-Change-Id: Idb069dabb80d34a0efdf04c3c40a42ab0c8a3f94 Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/355704 Original-Reviewed-by: Scott Collyer <scollyer@chromium.org> Squashed with: tpm: use 4 byte quantities when retrieving firmware version The CR50 device is capable of reporting its firmware version in 4 byte quantities, but the recently introduced code retrieves the version one byte at a time. With this fix the version is retrieved in 4 byte chunks. BRANCH=none BUG=none TEST=the version is still reported properly, as reported by the AP firmware console log: localhost ~ # grep cr50 /sys/firmware/log Firmware version: cr50_v1.1.4804-c64cf24 localhost ~ # Original-Commit-Id: 3111537e7b66d8507b6608ef665e4cde76403818 Original-Change-Id: I04116881a30001e35e989e51ec1567263f9149a6 Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/356542 Original-Reviewed-by: Andrey Pronin <apronin@chromium.org> Change-Id: Ia9f13a5bf1c34292b866f57c0d14470fe6ca9853 Signed-off-by: Martin Roth <martinroth@chromium.org> Reviewed-on: https://review.coreboot.org/15573 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2016-07-11tpm: use proper locality zero SPI bus addressesVadim Bendebury
The "PC Client Protection Profile for TPM 2.0" document defines SPI bus addresses for different localities. That definition is not honored in the cr50 implementation, this patch fixes it: locality zero register file is based off 0xd40000. BRANCH=none BUG=chrome-os-partner:54720 TEST=with the fixed cr50 image and the rest of TPM2 initialization patches applied factory initialization sequence on Gru succeeds. Change-Id: I49b7ed55f0360448b9a6602ebd31a3a531608da3 Signed-off-by: Martin Roth <martinroth@chromium.org> Original-Commit-Id: 43344fff5d58ec235e50030413fc38c98dd0a9a1 Original-Change-Id: I2de6fa6c05d3eca989d6785228d5adde1f2a7ab7 Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/355620 Original-Reviewed-by: Bill Richardson <wfrichar@chromium.org> Reviewed-on: https://review.coreboot.org/15568 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
2016-06-23kconfig: add missing SPI TPM CS config definitionVadim Bendebury
To fully define TPM attachment to a SPI interface both bus and CS (chip select) settings are required. Add the missing CS configuration option. BRANCH=none BUG=chrome-os-partner:50645 TEST=with the rest of the patches applied it is possible to compile in and run TPM2 SPI driver. Change-Id: If297df8e5b9526f156ed1414eb9db317d6af5b33 Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/353913 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/15299 Tested-by: build bot (Jenkins) Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-06-23tpm2: add SPI TPM driverVadim Bendebury
This introduces a SPI TPM driver compliant with the TCG issued "TPM Profile (PTP) Specification Revision 00.43" which can be found by googling its title. The driver implements both the hardware flow control protocol and the TPM state machine. The hardware flow control allows to map SPI based TPM devices to the LPC address space on x86 platforms, on all other platforms it needs to be implemented in the driver software. The tis layer is somewhat superficial, it might have to be expanded later. A lot more implementation details can be found in the code comments. Also, it is worth mentioning that this is not a complete version of the driver: its robustness needs to be improved, delay loops need to be bound, error conditions need to propagate up the call stack. BRANCH=none BUG=chrome-os-partner:52132, chrome-os-partner:50645, chrome-os-partner:54141 TEST=with the rest of the patches applied coreboot is able complete Chrome OS factory initialization of the TPM2 device. Change-Id: I967bc5c689f6e6f345755f08cb088ad37abd5d1c Signed-off-by: Martin Roth <martinroth@chromium.org> Original-Commit-Id: 5611c6f7d7fe6d37da668f337f0e70263913d63e Original-Change-Id: I17d732e66bd231c2289ec289994dd819c6276855 Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/350124 Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/15298 Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com> Tested-by: build bot (Jenkins)
2016-06-23kconfig: allow various tpm type and interface permutationsVadim Bendebury
Until now it was assumed that all TPM devices were of the same type (TCG 1.2 spec compliant) and x86 based boards had LPC connected TPMs and all other boards had I2C connected TPMs. With the advent of TPM2 specification there is a need to be able to configure different combinations of TPM types (TPM or TPM2) and interfaces (LPC, I2C and SPI). This patch allows to do it. Picking Chrome OS still assumes that the board has a TPM device, but adding MAINBOARD_HAS_TPM2 to the board's Kconfig will trigger including of TPM2 instead. MAINBOARD_HAS_LPC_TPM forces the interface to be set to LPC, adding SPI_TPM to the board config switches interface choice to SPI, and if neither of the two is defined, the interface is assumed to be I2C. BRANCH=none BUG=chrome-os-partner:50645 TEST=verified that none of the generated board configurations change as a result of this patch. With the rest of the stack in place it is possible to configure different combinations of TPM types and interfaces for ARM and x86 boards. Change-Id: I24f2e3ee63636566bf2a867c51ed80a622672f07 Signed-off-by: Martin Roth <martinroth@chromium.org> Original-Commit-Id: 5a25c1070560cd2734519f87dfbf401c135088d1 Original-Change-Id: I659e9301a4a4fe065ca6537ef1fa824a08d36321 Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/349850 Original-Reviewed-by: Martin Roth <martinroth@chromium.org> Reviewed-on: https://review.coreboot.org/15294 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
2016-05-09spi: Add support for Winbond W25Q256Varadarajan Narayanan
BUG=chrome-os-partner:49249 TEST=None. Initial code not sure if it will even compile BRANCH=none Change-Id: Ifde289ec004f5d54d5df32011c87e49470e2bb5d Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 613b5ae45f7b8325863d8be492a451e6d076e293 Original-Change-Id: I93386e058a60b5c9b61d89607cf8c6e0de6a21ca Original-Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org> Original-Reviewed-on: https://chromium-review.googlesource.com/334522 Original-Commit-Ready: David Hendricks <dhendrix@chromium.org> Original-Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: https://review.coreboot.org/14666 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-03-11spi/SST: fix write support for SST25VF064CAlexander Couzens
The SST25VF064C doesn't support the auto incrementing write which all other supported SST chips support. Allow the chips to select their write method. Change-Id: Ic088d35461a625469ee6973d1267d7dd11963496 Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Reviewed-on: https://review.coreboot.org/14000 Tested-by: build bot (Jenkins) Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2015-10-31tree: drop last paragraph of GPL copyright headerPatrick Georgi
It encourages users from writing to the FSF without giving an address. Linux also prefers to drop that and their checkpatch.pl (that we imported) looks out for that. This is the result of util/scripts/no-fsf-addresses.sh with no further editing. Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: http://review.coreboot.org/11888 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2015-10-05Add EM100 'hyper term' spi console support in ramstage & smmMartin Roth
The EM100Pro allows the debug console to be sent over the SPI bus. This is not yet working in romstage due to the use of static variables in the SPI driver code. It is also not working on chipsets that have SPI write buffers of less than 10 characters due to the 9 byte command/header length specified by the EM100 protocol. While this currently works only with the EM100, it seems like it would be useful on any logic analyzer with SPI debug - just filter on command bytes of 0x11. Change-Id: Icd42ccd96cab0a10a4e70f4b02ecf9de8169564b Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: http://review.coreboot.org/11743 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2015-09-07Drop "See file CREDITS..." commentStefan Reinauer
coreboot has no CREDITS file. Change-Id: Iaa4686979ba1385b00ad1dbb6ea91e58f5014384 Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-on: http://review.coreboot.org/11514 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2015-07-29arm, arm64, mips: Add rough static stack size checks with -Wstack-usageJulius Werner
We've seen an increasing need to reduce stack sizes more and more for space reasons, and it's always guesswork because no one has a good idea how little is too litte. We now have boards with 3K and 2K stacks, and old pieces of common code often allocate large temporary buffers that would lead to very dangerous and hard to detect bugs when someone eventually tries to use them on one of those. This patch tries improve this situation at least a bit by declaring 2K as the minimum stack size all of coreboot code should work with. It checks all function frames with -Wstack-usage=1536 to make sure we don't allocate more than 1.5K in a single buffer. This is of course not a perfect test, but it should catch the most common situation of declaring a single, large buffer in some close-to-leaf function (with the assumption that 0.5K is hopefully enough for all the "normal" functions above that). Change one example where we were a bit overzealous and put a 1K buffer into BSS back to stack allocation, since it actually conforms to this new assumption and frees up another kilobyte of that highly sought-after verstage space. Not touching x86 with any of this since it's lack of __PRE_RAM__ BSS often requires it to allocate way more on the stack than would usually be considered sane. BRANCH=veyron BUG=None TEST=Compiled Cosmos, Daisy, Falco, Blaze, Pit, Storm, Urara and Pinky, made sure they still build as well as before and don't show any stack usage warnings. Change-Id: Idc53d33bd8487bbef49d3ecd751914b0308006ec Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 8e5931066575e256dfc2295c3dab7f0e1b65417f Original-Change-Id: I30bd9c2c77e0e0623df89b9e5bb43ed29506be98 Original-Signed-off-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/236978 Original-Reviewed-by: David Hendricks <dhendrix@chromium.org> Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/9729 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2015-06-02cbfs: new API and better program loadingAaron Durbin
A new CBFS API is introduced to allow making CBFS access easier for providing multiple CBFS sources. That is achieved by decoupling the cbfs source from a CBFS file. A CBFS source is described by a descriptor. It contains the necessary properties for walking a CBFS to locate a file. The CBFS file is then decoupled from the CBFS descriptor in that it's no longer needed to access the contents of the file. All of this is accomplished using the regions infrastructure by repsenting CBFS sources and files as region_devices. Because region_devices can be chained together forming subregions this allows one to decouple a CBFS source from a file. This also allows one to provide CBFS files that came from other sources for payload and/or stage loading. The program loading takes advantage of those very properties by allowing multiple sources for locating a program. Because of this we can reduce the overhead of loading programs because it's all done in the common code paths. Only locating the program is per source. Change-Id: I339b84fce95f03d1dbb63a0f54a26be5eb07f7c8 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/9134 Tested-by: build bot (Jenkins) Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2015-05-28Remove leftover tseg_relocateVladimir Serbinenko
Change-Id: I534f992ed479c7cdc049bd598259b1f1cf2953b9 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/10354 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2015-05-21Remove address from GPLv2 headersPatrick Georgi
As per discussion with lawyers[tm], it's not a good idea to shorten the license header too much - not for legal reasons but because there are tools that look for them, and giving them a standard pattern simplifies things. However, we got confirmation that we don't have to update every file ever added to coreboot whenever the FSF gets a new lease, but can drop the address instead. util/kconfig is excluded because that's imported code that we may want to synchronize every now and then. $ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, *MA[, ]*02110-1301[, ]*USA:Foundation, Inc.:" {} + $ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin Street, Suite 500, Boston, MA 02110-1335, USA:Foundation, Inc.:" {} + $ find * -type f -exec sed -i "s:Foundation, Inc., 59 Temple Place[-, ]*Suite 330, Boston, MA *02111-1307[, ]*USA:Foundation, Inc.:" {} + $ find * -type f -exec sed -i "s:Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.:Foundation, Inc.:" {} + $ find * -type f -a \! -name \*.patch \ -a \! -name \*_shipped \ -a \! -name LICENSE_GPL \ -a \! -name LGPL.txt \ -a \! -name COPYING \ -a \! -name DISCLAIMER \ -exec sed -i "/Foundation, Inc./ N;s:Foundation, Inc.* USA\.* *:Foundation, Inc. :;s:Foundation, Inc. $:Foundation, Inc.:" {} + Change-Id: Icc968a5a5f3a5df8d32b940f9cdb35350654bef9 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: http://review.coreboot.org/9233 Tested-by: build bot (Jenkins) Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
2015-05-04drivers/spi/stmicro: Rename N25Q256A to N25Q256David Imhoff
The 'A' indicates the production process(64 nm). All other chips from the same family leave this out. TEST=Build and booted on Minnowboard Max Change-Id: I21e6c01de5d547bbc2252e679a001948e7ab752c Signed-off-by: David Imhoff <dimhoff_devel@xs4all.nl> Reviewed-on: http://review.coreboot.org/10078 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2015-05-04drivers/spi/stmicro: Add '.op_erase' for N25Q256David Imhoff
'.op_erase' was not specified for this chip. Set it to sub sector erase(CMD_M25PXX_SSE). Adjust page/sector size for sub sector erase to work. TEST=Untested, due to lack of hardware. Change-Id: Icc2748fbd3afeb56693e1c17d97eb490fba67064 Signed-off-by: David Imhoff <dimhoff_devel@xs4all.nl> Reviewed-on: http://review.coreboot.org/10077 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2015-05-04drivers/spi/stmicro: Add N25Q064 supportDavid Imhoff
N25Q064 is similar to N25Q128. TEST=Build and booted twice on Minnowboard Max Change-Id: Iec105f8b81f619846cf40b40042cc59150b81149 Signed-off-by: David Imhoff <dimhoff_devel@xs4all.nl> Reviewed-on: http://review.coreboot.org/10076 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2015-05-04spi: Remove out of date comment and reorder flash tableDavid Imhoff
What is described by the comment has already been fixed in f0d038f4 (flash: use two bytes of device ID to identify stmicro chips). This also means that STM_ID_N25Q128 doesn't have to be at the top of stmicro_spi_flash_table anymore. TEST=Untested, due to lack of hardware Change-Id: I7a9e9a0cdfdb1cf34e914e186fc6957c1d9b5ca6 Signed-off-by: David Imhoff <dimhoff_devel@xs4all.nl> Reviewed-on: http://review.coreboot.org/10068 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2015-05-04spi: Change 'page' to 'sector' in log messageDavid Imhoff
The log message says 'page size' while actually the sector size is printed. This is confusing since for stmicro page size != sector size. Also add '0x' prefix to numbers to make it clear they are in hex. TEST=Build and booted on Minnowboard Max Change-Id: I795a4b7c1bc8de2538a87fd4ba56f5a78d9ca2ac Signed-off-by: David Imhoff <dimhoff_devel@xs4all.nl> Reviewed-on: http://review.coreboot.org/10067 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2015-04-17flash: use two bytes of device ID to identify stmicro chipsDaisuke Nojiri
stmicro flash chips use 2 bytes as a device id: upper byte for memory type and lower byte for capacity. with this change, we will use all 2 bytes to identify a chip. BUG=none BRANCH=broadcom-firmware TEST=booted purin and verified n25q256a was identified. Change-Id: I8f382eddc4fa70d3deceb4f9d2e82026a7025629 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 12f70a1d4b7e1142afec9ce097c4a21b6225f66e Original-Change-Id: Id3378a77318fabb74ddb30f1a9549010636872ba Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Original-Reviewed-on: https://chrome-internal-review.googlesource.com/199387 Original-Reviewed-by: Corneliu Doban <cdoban@broadcom.com> Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Original-Commit-Queue: Daisuke Nojiri <dnojiri@google.com> Original-Tested-by: Daisuke Nojiri <dnojiri@google.com> Original-Reviewed-on: https://chromium-review.googlesource.com/251305 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/9774 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
2015-04-17spi: allow inclusion of Micronix and STM drivers in bootblockVadim Bendebury
Bootblock does not allow using malloc, use statically allocated chip structures instead. BRANCH=storm BUG=chrome-os-partner:33489 TEST=both drivers compile when configured in, also booted whirlwind with an STM compatible SPI NOR flash. Change-Id: I154c33ce5fc278d594205d8b8e62a56edb4e177e Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: eedbb959a595e0898e7a1dd551fc7c517a02f370 Original-Change-Id: I29b37107ac1d58a293f531f59ee76b3d8c4b3e7c Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/248992 Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/9772 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2015-04-17spi: Add function to read flash status registerDuncan Laurie
Add a function that allows reading of the status register from the SPI chip. This can be used to determine whether write protection is enabled on the chip. BUG=chrome-os-partner:35209 BRANCH=haswell TEST=build and boot on peppy Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/240702 Reviewed-by: Shawn N <shawnn@chromium.org> (cherry picked from commit c58f17689162b291a7cdb57649a237de21b73545) Change-Id: Ib7fead2cc4ea4339ece322dd18403362c9c79c7d Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 9fbdf0d72892eef4a742a418a347ecf650c01ea5 Original-Change-Id: I2541b22c51e43f7b7542ee0f48618cf411976a98 Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/241128 Original-Reviewed-by: Shawn N <shawnn@chromium.org> Reviewed-on: http://review.coreboot.org/9730 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2015-04-17drivers/spi: Pass flash parameters from coreboot to payloadDan Ehrenberg
A payload may want to run erase operations on SPI NOR flash without re-probing the device to get its properties. This patch passes up three properties of flash to achieve that: - The size of the flash device - The sector size, i.e., the granularity of erase - The command used for erase The patch sends the parameters through coreboot and then libpayload. The patch also includes a minor refactoring of the flash erase code. Parameters are sent up for just one flash device. If multiple SPI flash devices are probed, the second one will "win" and its parameters will be sent up to the payload. TEST=Observed parameters to be passed up to depthcharge through libpayload and be used to correctly initialize flash and do an erase. TEST=Winbond and Gigadevices spi flash drivers compile with the changes; others don't, for seemingly unrelated reasons. BRANCH=none BUG=chromium:446377 Change-Id: Ib8be86494b5a3d1cfe1d23d3492e3b5cba5f99c6 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 988c8c68bbfcdfa69d497ea5f806567bc80f8126 Original-Change-Id: Ie2b3a7f5b6e016d212f4f9bac3fabd80daf2ce72 Original-Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/239570 Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org> Reviewed-on: http://review.coreboot.org/9726 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2015-04-13spi: support controllers with limited transfer size capabilitiesVadim Bendebury
Some SPI controllers (like Imgtec Pistachio), have a hard limit on SPI read and write transactions. Limiting transfer size in the wrapper allows to provide the API user with unlimited transfer size transactions. The tranfer size limitation is added to the spi_slave structure, which is set up by the controller driver. The value of zero in this field means 'unlimited transfer size'. It will work with existion drivers, as they all either keep structures in the bss segment, or initialize them to all zeros. This patch addresses the problem for reads only, as coreboot is not expected to require to write long chunks into SPI devices. BRANCH=none BUG=chrome-os-partner:32441, chrome-os-partner:31438 TEST=set transfer size limit to artificially low value (4K) and observed proper operation on both Pistachio and ipq8086: both Storm and Urara booted through romstage and ramstage. Change-Id: Ibb96aa499c3eec458c94bf1193fbbbf5f54e1477 Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Original-Commit-Id: 4f064fdca5b6c214e7a7f2751dc24e33cac2ea45 Original-Change-Id: I9df24f302edc872bed991ea450c0af33a1c0ff7b Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/232239 Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Original-Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/9571 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2015-03-20verstage should include the CBFS SPI wrapper, when configuredVadim Bendebury
Vboot2 targets so far did not have COMMON_CBFS_SPI_WRAPPER configuration option enabled, so the verstage is missing the relevant files in some Makefiles. This patch fixes the problem. BRANCH=none BUG=none TEST=with the rest of the patches applied cosmos target builds fine with COMMON_CBFS_SPI_WRAPPER enabled Change-Id: I3ce78c8afc5f7d8ce822bbf8dd789c0c2ba4b99c Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: b72693c96f7d8ce94ce6fe12b316d5b88fded579 Original-Change-Id: Iab813b9f5b0156c45b007fe175500ef0de50e65c Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/223751 Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/8772 Tested-by: build bot (Jenkins) Reviewed-by: David Hendricks <dhendrix@chromium.org>
2015-03-20spi: Add GigaDevice GD25LQ64C/GD25LB64C SPI ROM supportMarc Jones
GD25LQ64C and GD25LB64C have the same ID and settings. BUG=chrome-os-partner:25907 BRANCH=baytrail TEST=Boot with GD25LQ64 and check MRC data save/restore works. Change-Id: I8a4aa7cabd9a7657c2f0bae255a87341db3f1061 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 20b5896adbbbdedcb1b7de435466dcc6bfa703cb Original-Change-Id: I86d1e69552b6000faa9e0523356e27d7e2a6a6db Original-Signed-off-by: Marc Jones <marc.jones@se-eng.com> Original-Reviewed-on: https://chromium-review.googlesource.com/193238 Original-Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org> Original-Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/8770 Tested-by: build bot (Jenkins) Reviewed-by: David Hendricks <dhendrix@chromium.org>
2015-03-20spi: do not use malloc in Gigadevice driverDavid Hendricks
This allows us to use the driver before ramstage. BRANCH=none BUG=none TEST=built and booted on Pinky Change-Id: I0700388b0e4e0562e3c0a52863c8357097bfd8d6 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: cd57587dab74de509d5c50cfc1ad337d765af6c8 Original-Signed-off-by: David Hendricks <dhendrix@chromium.org> Original-Change-Id: I0ce901331e401274254b8889484ffb41359119fa Original-Reviewed-on: https://chromium-review.googlesource.com/235864 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: http://review.coreboot.org/8774 Tested-by: build bot (Jenkins) Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2015-03-20spi: do not use malloc in Winbond driverVadim Bendebury
When the driver is included in bootblock, malloc() is not available. Come to think of it, it is perfectly fine to use a statically allocated structure for the SPI device descriptor - coreboot is unlikely to require concurrent support of multiple SPI devices of the same kind. BRANCH=none BUG=chrome-os-partner:31438 TEST=bootblock on the FPGA board recognizes the installed Winbond device: coreboot-4.0 bootblock Tue Nov 11 07:27:24 PST 2014 starting... SF: Detected W25Q16 with page size 1000, total 200000 Change-Id: Iea1936a219d38848580a10f75eb8bbcab17e6507 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 0b4082442aa526d387a80cb5872d78670e6b468b Original-Change-Id: Iaa69d610ef18e69b1ae5ade2d958f9fe1595a723 Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/228959 Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/8771 Tested-by: build bot (Jenkins) Reviewed-by: David Hendricks <dhendrix@chromium.org>
2015-03-20spi_flash: add support for S25FL116KDaisuke Nojiri
S25FL116K family uses the first 3 bytes in response to a legacy identification command (9f) while previously supported models use the last 4 bytes. This change defines identify functions to allow both types to be handled correctly. BUG=none BRANCH=tot TEST=verified romstage is loaded on cosmos development board. Change-Id: I1970a9af17e81299fada5029724d405de4022156 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 65ff436db2355cb68a766a3dedbcd7e2f765e6db Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Original-Change-Id: Icdd2645e356652672c4482e7b805da1bc0f21e71 Original-Reviewed-on: https://chromium-review.googlesource.com/234431 Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org> Reviewed-on: http://review.coreboot.org/8773 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2015-01-09spi: Add Spansion flash S25FL128PVadim Bendebury
Storm devices use more recent Spansion flash, add its description to the table of supported devices. BUG=chrome-os-partner:29871 TEST=the updated firmware boots all the way to depthcharge Original-Change-Id: I81661c01ae679d49918e40d940b8d348f3081f9a Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/205182 Original-Reviewed-by: Stefan Reinauer <reinauer@google.com> (cherry picked from commit ea7bb1cf65b7130164b869fef09c55138100206b) Signed-off-by: Marc Jones <marc.jones@se-eng.com> Change-Id: I1e0136a5c575951b4e464aab0f380f19e886a84f Reviewed-on: http://review.coreboot.org/8146 Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2014-12-30SPI: Add Eon EN25S64 support.Marc Jones
BUG=chrome-os-partner:25907 BRANCH=baytrail(rambi) TEST=Read and write MRC and ELOG on Glimmer with Eon device. Original-Change-Id: If883ff6eb14dd49a06f57a01ca61661854ded78d Original-Reviewed-on: https://chromium-review.googlesource.com/198324 Original-Reviewed-by: David Hendricks <dhendrix@chromium.org> Original-Commit-Queue: Marc Jones <marc.jones@se-eng.com> Original-Tested-by: Marc Jones <marc.jones@se-eng.com> (cherry picked from commit 536c34c2d92178f4e62b8ca7cfffceaf80a305f6) Signed-off-by: Marc Jones <marc.jones@se-eng.com> Change-Id: I199451ed2b29c55bfb5e1487afa8cf3b9978e63e Reviewed-on: http://review.coreboot.org/7935 Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins)
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-12 12:57:36 +0000