Age | Commit message (Collapse) | Author |
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I926ec4c1c00339209ef656995031026935e52558
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77637
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The sta_himax83102 panel sometimes shows abnormally flickering
horizontal lines. The front gate output will precharge the X point of
the next pole circuit before TP term starts, and wait until the end of
the TP term to resume the CLK. For this reason, the X point must be
maintained during the TP term. In abnormal case, we measured a slight
leakage at point X. This is because during the TP term, the GPW does not
fully pull the VGL low, causing the TFT to not be closed tightly.
To fix this, we completely pull GPW to VGL before entering the TP term.
This will ensure that the TFT is closed tightly and prevent the abnormal
display.
BUG=b:299249186
BRANCH=corsola
TEST=FW Screen display normally
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I5dddaaa38917a65990c1474b657db5eb551940b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77692
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In the datasheet of ILI9882T [1] section 3.11 Power On/Off Sequence,
the TReset-CMD (Reset to First Command in Display Sleep In Mode) should
be larger than 10ms, but it's 1.1ms now. This may cause abnormal
display as some commands may be lost during power on. Fix this and
leave some margins by increasing TReset-CMD to 20ms. Also, to align
with the kernel driver structure starry_ili9882t_init_cmd, add 20ms
delay at the end of command.
[1] ILI9882T_Datasheet_20220428.pdf
BUG=b:293380212
TEST=Boot and display normally
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Ifdcaf0e34753fc906817c763f1c8e7389448d1dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76766
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
There is a problem of screen shake on the old panel[1]. So increase the
panel GOP component pull-down circuit size in hardware, and update the
initialization code at the same time. The new initialization code is
mainly adjusted for GOP timing. When Display sleep in, raise all GOP
signals to VGHO and then drop to GND. In order to be consistent with
the current panel model, let's rename this file.
[1]: INX old panel product number is HJ110IZ-01A-B1, and the new
panel product number is HJ110IZ-01A-B2. We have recalled the shipment
old panel.
BUG=b:270276344
BRANCH=trogdor
TEST= test firmware display pass
Change-Id: I2b2534afee1ed700c39d3c360aafd685b63ccbfb
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
coreboot logs the error below, since the value of hporch is too small. Increasing hbl from 80 to 174, and hso from 40 to 72 to revise the HBP(Horizontal Back Porch) and HFP(Horizontal Front Porch). After revising this, the actual measurement frame rate is 60.1Hz.
[ERROR]HFP plus HBP is not greater than d_phy, the panel may not work
properly.
BUG=b:284812193
TEST=cbmem -c | grep "ERROR" and measure frame rate
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I7de5984ce8aec12d8ebe292974e05776835330d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76218
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add STA_ILI9882T panel serializable data to CBFS.
The panel datasheet: ILI9882T_Datasheet_20220428.pdf
BUG=b:275470328
BRANCH=corsola
TEST=build and check the CBFS include the panel
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Ia7a37c0659f0959fe7be01aba0f08d63119d139f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
|
|
Add STA_HIMAX83102_J02 panel serializable data to CBFS.
The panel datasheet: HX83102-J02_Datasheet_v03.pdf.
BUG=b:272425116
BRANCH=corsola
TEST=build and check the CBFS include the panel
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I382bdc89e5a217fd1c28e677938f454dc09725cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ia40678019b2a54deb246dbfbf33ec37a8c3839e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
cb_err_t was meant to be used in place of `enum cb_err` in all
situations, but the choice to use a typedef here seems to be
controversial. We should not be arbitrarily using two different
identifiers for the same thing across the codebase, so since there are
no use cases for serializing enum cb_err at the moment (which would be
the primary reason to typedef a fixed-width integer instead), remove
cb_err_t again for now.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Iaec36210d129db26d51f0a105d3de070c03b686b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add mipi panel support for wormdingler
- Add the following panel for wormdingler:
INX P110ZZD-DF0
BOE TV110C9M-LL0
- Use panel_id to distinguish which mipi panel to use.
- Setup panel orientation
BUG=b:195898400,b:198548221
BRANCH=none
TEST=emerge-strongbad coreboot
Change-Id: I8cd28e024ecbfdcd473bc39efb529eb4aca1b5d0
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Our MIPI panel initialization framework differentiates between DCS and
GENERIC commands, but the exact interpretation of those terms is left to
the platform drivers. In practice, the MIPI DSI transaction codes for
these are standardized and platforms always need to do the same
operation of combining the command length and transfer type into a
correct DSI protocol code. This patch factors out the various
platform-specific DSI protocol definitions into a single global one and
moves the transaction type calculation into the common panel framework.
The Qualcomm SC7180 implementation which previously only supported DCS
commands is enhanced to (hopefully? untested for now...) also support
GENERIC commands. While we're rewriting that whole section also fix some
other issues about how exactly long and short commands need to be passed
to that hardware which we identified in the meantime.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I09ade7857ca04e89d286cf538b1a5ebb1eeb8c04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
It doesn't make sense to store the orientation field directly in the
panel information structure, which is supposed to be reuseable between
different boards. The thing that determines orientation is how that
panel is built into the board in question, which only the board itself
can know. The same portrait panel could be rotated left to be used as
landscape in one board and rotated right to be used as landscape in
another. This patch moves the orientation field out of the panel
structure back into the mainboards to reflect this.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If2b716aa4dae036515730c12961fdd8a9ac34753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57324
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sounds like we prefer to have this under drivers/ instead of device/.
Also move all MIPI-related headers out from device/ into their own
directory.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib3e66954b8f0cf85b28d8d186b09d7846707559d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|