| Age | Commit message (Collapse) | Author |
|---|
|
This patch introduces CONFIG_I2C_TRANSFER_TIMEOUT_US,
which controls how long to wait for an I2C devices to
produce/accept all the data bytes in a single transfer.
(The device can delay transfer by stretching the clock of
the ack bit.)
The default value of this new setting is 500ms. Existing
code had timeouts anywhere from tens of milliseconds to a
full second beween various drivers. Drivers can still have
their own shorter timeouts for setup/communication with the
I2C host controller (as opposed to transactions with I2C
devices on the bus.)
In general, the timeout is not meant to be reached except in
situations where there is already serious problem with the
boot, and serves to make sure that some useful diagnostic
output is produced on the console.
Change-Id: I6423122f32aad1dbcee0bfe240cdaa8cb512791f
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch replaces remaining `cb_err_t` with `enum cb_err` after commit
hash 69cc557c (commonlib/bsd: Remove cb_err_t) removes majority of
`cb_err_t` instances.
TEST=Able to build the brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3392f9c2cfb4a889a999c8ea25066c89979f0900
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This allows mainboards using an I2C bus to communicate with the cr50
to reuse the functionality related to firmware version and BOARD_CFG.
BUG=b:202246591
TEST=boot on brya0, see cr50 FW version in logs
Change-Id: Ide1a7299936193da3cd3d15fdfd1a80994d70da0
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Turns out 200ms still isn't enough in the worst reset conditions.
There's been some reports of failures at 200ms with some older
cr50 versions. Let's not take any chances and bump this way up
since if this fails, it prevents boot.
BUG=b:213828947
BRANCH=None
TEST=Reboot and suspend_stress on Nipperkin
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I5be0a80c064546fd277f66135abc9d0572df11cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The `chip` argument passed around to many functions in this driver is
actualy unused, so remove it where it is unused.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib8d32fdf340c8ef49fefd11da433e3b6ee561f29
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Now that the console system itself will clearly differentiate loglevels,
it is no longer necessary to explicitly add "ERROR: " in front of every
BIOS_ERR message to help it stand out more (and allow automated tooling
to grep for it). Removing all these extra .rodata characters should save
us a nice little amount of binary size.
This patch was created by running
find src/ -type f -exec perl -0777 -pi -e 's/printk\(\s*BIOS_ERR,\s*"ERROR: /printk\(BIOS_ERR, "/gi' '{}' ';'
and doing some cursory review/cleanup on the result. Then doing the same
thing for BIOS_WARN with
's/printk\(\s*BIOS_WARNING,\s*"WARN(ING)?: /printk\(BIOS_WARNING, "/gi'
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I3d0573acb23d2df53db6813cb1a5fc31b5357db8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Lance Zhao
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
|
|
The speed control bits of the Designware I2C controller are bits 1 and 2
in the control register, so the values should be written as number
shifted by the number of the first bit. The resulting constant is
identical.
TEST=Timeless build for amd/chausie results in identical binary
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id0881dfcd7703ab6a70a9b1a355d5a93771aebc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Using enum cb_err as return type instead of int improves the readability
of the code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8d96e5f72a8b3552ab39c1d298bafcc224bf9e55
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61512
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Outside of the designware I2C driver the generic platform_i2c_transfer
function should be used instead, so don't make dw_i2c_transfer available
outside of this file.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib8b6a08b6aa2cd63adc2ef69b828661fa0ed154a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Using enum cb_err as return type instead of int improves the readability
of the code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic1812c4d8d2b4d9ad331a787bd302a4f0707c1fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Using enum cb_err as return type instead of int improves the readability
of the code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I55e6d93ca141b687871ceaa763bbbbe966c4b4a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
|
|
Using enum cb_err as return type instead of int improves the readability
of the code. This commit only changes the return value of the static
functions in this file keeping the external interface identical.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I80300e0b24591fc660c3134139b9257e002cdbbb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
size_t is defined in stddef.h and not stdint.h, so include types.h to
get both.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3782d3a949b72d1530ebd8078c46bc695f76dc4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This will provide the definitions for size_t, uint32_t and uintptr_t.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Icda8d458565bf981545d720d612cbdace04bedd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Add driver for setting up Semtech sx9360 SAR sensor.
The driver is based on sx9310.c. The core of the driver is the same, but
the bindings are slightly different.
Registers are documented in the kernel tree:
Documentation/devicetree/bindings/iio/proximity/semtech,sx9360.yaml
[https://patchwork.kernel.org/project/linux-iio/patch/20211213024057.3824985-4-gwendal@chromium.org/]
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Change-Id: I0a912f184e6f3501f894cca24c0d71a2c3087516
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Turns out 150ms isn't enough in the worst reset conditions. On guybrush
the TPM is reset in S0i3 and the CR50 is allowed to hibernate. The CR50
is woken up and initialized early during S0i3 resume. Occasionally the
CR50 isn't ready before the probe times out.
BUG=b:213828947
BRANCH=None
TEST=suspend_stress_test -c 1000
Change-Id: Ifda438080cf1ad2796c7061223a6a97b8e6e9987
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Keith Short <keithshort@chromium.org>
|
|
I2C bus and address of the TPM are typically fixed on hardware so
there is no need to be able to configure this in menuconfig.
Change-Id: I1b6afa68fe753fb76348e0461209d218b14df7cb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Found using:
diff <(git grep -l '#include <stdlib.h>' -- src/) <(git grep -l 'memalign(\|malloc(\|calloc(\|free(' -- src/)
Change-Id: Id3bd3d8a2d3609a13ecbc4eab14ba745e6365cab
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
CB:59479 introduced a blank default statement. This is treated as an
error or warning on some older toolchains. Add a break statement on
default case.
BUG=None
TEST=Build the Guybrush mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I3d034cfebc8b8ae7d7024d41b4b2207cdeb083e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Introduce firmware-power-managed DSD ACPI property for TPM devices.
This property can be checked by the kernel TPM driver to override how
the TPM power states are managed. This is a tri-state flag, true,
false, or unset. So an enum used to keep the flag is unset by default.
When firmware-power-managed is true, the kernel driver will not send a
shutdown during s2idle/s0i3 suspend.
BUG=b:200578885
BRANCH=None
TEST=TPM shutdown is triggered on s0ix suspend on guybrush with patched
kernel
Change-Id: Ia48ead856fc0c6e637a2e07a5ecc58423f599c5b
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
These issues were found and fixed by codespell, a useful tool for
finding spelling errors.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I5b8ecdfe75d99028fee820a2034466a8ad1c5e63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58080
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add two properties (maxim, vmon-slot-no/maxim, imon-slot-no) in maxim9839 driver.
This is I/V source destination definition that from below properties .
maxim,vmon-slot-no => PCM_IVADC_V_DEST
maxim,imon-slot-no => PCM_IVADC_I_DEST
BUG=b:197076844
TEST=build and check SSDT
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Idb24d19c7cfea559bf6d53f401d66cadb8b3acc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Maxim driver look for "maxim,dsm_param_name" to load dsm parameter file.
dsm param file name consist of {dsm_param_file_name} filled in devicetree,
{MAINBOARD_VENDOR} and {MAINBOARD_PART_NUMBER}.
=> {dsm_param_file_name}_{MAINBOARD_VENDOR}_{MAINBOARD_PART_NUMBER}.bin
BUG=b:197076844
TEST=build, and check ssdt
Change-Id: I006572d6a6ea55298374c688dfd9d877835da82d
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Move bcd2bin() / bin2bcd() functions to commonlib/bsd/include/
Also, the license is changed from GPL to BSD.
This is because it is needed from "utils" (see CL in the chain).
For reference bin2bcd() & bcd2bin() are very simple functions.
There are already BSD implementations, like these ones (just to
name a few):
https://chromium.googlesource.com/chromiumos/platform/mosys/+/refs/heads/main/include/lib/math.h#67
http://web.mit.edu/freebsd/head/sys/contrib/octeon-sdk/cvmx-cn3010-evb-hs5.c
BUG=b:172210863
TEST=make (everything compiled Ok).
Change-Id: If2eba82da35838799bcbcf38303de6bd53f7eb72
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56904
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The DA7219 does not support wake from D3cold, therefore update the
return value of _S0W from D3cold to D3hot.
BUG=b:187228954
TEST=compile
Change-Id: If03f83bb00ec90a2a6646d2c99d8bcc7e5533ac2
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Since the OS provides its own driver for the I2C controller it can
choose to use a bus speed other than the one used at coreboot runtime.
In this case it would be good to provide a way how the needed bus
timings are communicated to the OS, since these are very board-specific
and there is no way that the OS can know them other than read the
appropriate ACPI reported timings.
This patch adds some code to report additional bus speed timings if
there are some defined in the devicetree.
Change-Id: If921e0613864660dc1bb8d7c1b30fb9db8ac655d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
In commit b64db833d6 a basic ACPI support was added to the driver.
With this support an SSDT-entry is created for this RTC and it is now
visible to the OS via ACPI. In Linux the PNP-devices, which are
reported over ACPI, are scanned rather early and if the entry is found,
the device is claimed even if there is no driver available yet.
In this case, when the native RTC-driver without ACPI-support is loaded
and tries to register this device, the RTC is already blocked by the
PNP-drivers and cannot be used anymore. This leads to a non-usable RTC
on kernels where the needed ACPI-extension is not yet merged into the
RTC driver.
This patch provides a way to disable the ACPI-support for the RTC if
needed.
Change-Id: Ic65794d409d13a78d17275c86ec14ee6f04cd2a6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55003
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
HSBIAS_SENSE_EN configures HSBIAS output current sense through
the external 2.21-k resistor. HSBIAS_SENSE is hardware feature to reduce
the potential pop noise during the headset plug out slowly. But on some
platforms ESD voltage will affect it causing test to fail, especially
with CTIA headset type. For different hardware setups, a designer might
want to tweak default behavior.
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.corp-partner.google.com>
Change-Id: I87c6f01af1bdb5b1cb8e399191519598d7fbe9ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52981
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If device is supported as a wake source, _S0W should be set to D3hot.
This ensures that the device is put into D3hot by the OSPM.
Power resource(PRIC) for the device is listed in both _PR0 and _PR3. Thus, it ensures that the OSPM does not turn off power resource when device is put into D0 and D3hot. Hence, it is capable of waking the system from D3hot state. However, if it is put into D3cold, then the power resource is turned off by the OSPM.
The devices we are currently looking at for touchscreen/touchpad
do not really support auxiliary power and so do not support wake from D3cold.
BUG=b:186070097
TEST=build and check device wake state _S0W set to 3 in ssdt table.
Change-Id: I34e4b2350875530d3337be700276bcc4fb1f810a
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Inspired by discussion in CB:22822.
If I2C bus step response has not been measured, assume the layout to
have been designed with a minimal capacitance and SCL rise and fall
times of 0 ns. The calculations will add the required amount of
reference clocks for the host to drive SCL high or low, such that the
maximum bus frequency specification is met.
Change-Id: Icbafae22c83ffbc16c179fb5412fb4fd6b70813a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52723
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This driver uses the ACPI Device Property interface to generate
the required parameters into the _DSD table format expected by
the kernel
This was tested on the octopus/variants/fleex ainboard to ensure
that the SSDT contained the equivalent parameters that are provided
by the current DSDT object
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.corp-partner.google.com>
Change-Id: I7c3145b20a1ba743d91eb64b93cb001db3854c5d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This adds a driver for the TI TAS5825M smart amplifier [1].
The driver expects the mainboard using it to define tas5825m_setup(),
which uses the tas5825m_* functions to set configuration data. Each
mainboard may have very different configuration data, depending on
its audio hardware.
Tested on System76 addw1, bonw14, oryp5, and oryp6.
[1]: https://www.ti.com/product/TAS5825M
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Change-Id: I896e8f272f18e64bfc90f406e7d4163010800aaf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add definitions to describe GPIOs in generated ACPI objects.
The method allow either write a GpioInt() or Interrupt() descriptor.
Signed-off-by: Seven Lee <wtli@nuvoton.com>
Change-Id: I37fec7b0b9324dbfb61b7a8bea80f45026c54409
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51922
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current driver is using chip registers map to configure the SAR
sensor, which is opaque, especially when the datasheet is not published
widely.
Use more descriptive names, as defined in Linux kernel documentation at
https://www.kernel.org/doc/Documentation/devicetree/bindings/iio/proximity/semtech%2Csx9310.yaml
BUG=b:173341604
BRANCH=volteer
TEST=Dump all tables, check semtech property:
for i in $(find /sys/firmware/acpi/tables/ -type f) ; do
f=$(basename $i); cat $i > /tmp/$f.dat ; iasl -d /tmp/$f.dat
done
In SSDT.dsl, we have:
Package (0x06)
{
Package (0x02)
{
"semtech,cs0-ground",
Zero
},
Package (0x02)
{
"semtech,startup-sensor",
Zero
},
Package (0x02)
{
"semtech,proxraw-strength",
Zero
},
Package (0x02)
{
"semtech,avg-pos-strength",
0x0200
},
Package (0x02)
{
"semtech,combined-sensors",
Package (0x03)
{
Zero,
One,
0x02
}
},
Package (0x02)
{
"semtech,resolution",
"finest"
}
}
Change-Id: I8d1c81b56eaeef1dbb0f73c1d74c3a20e8b2fd7b
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In commit 2609eaaa8f (src/drivers/i2c/rx6110sa: Omit _HID temporarily)
the randomly assigned and therefore wrong ACPI ID for RTC RX6110SA was
removed. In the meantime Seiko-Epson did a great job and registered an
official vendor ID in the ACPI database [1]. Further on, Seiko-Epson
has now assigned the unique Product Identifier for the RX6110SA, which
is '6110'. The assignment of the Product Identifier is controlled by
the vendor and there is no official database where this ID is stored
in. It is up to the vendor to make sure that this ID stays unique.
This patch adds this new vendor and product ID to the driver. Together
with a pending Linux patch this RTC is now useable as ACPI device in
Linux.
[1] https://uefi.org/ACPI_ID_List?search=SECC
Change-Id: I45838162f014a760520692c6dcaae329ad98547d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51176
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Johannes Hahn <johannes-hahn@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
This change ensures that the IRQ is appropriately configured.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild. Build and boot to OS in Dedede.
Change-Id: I3245a9de6e88cd83528823251083e62288192f0d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: If2751f3672072b7fa421ae33dc6e1490fdf35247
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Change-Id: I28f976118a380ef05a98257e9d57aadc26b69cb5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Change-Id: I598d27995fad7582ff41f4e7deaeb2e75e8ebde9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Add IrqCfg1 register for proximity IRQ function and polarity setting.
BUG=b:175932166
BRANCH=dedede
TEST=Build passed.
Change-Id: I3cee84a5658fecf55d2d8b8621879588ffe0158d
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49220
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DRIVER_I2C_TPM_ACPI is used to enable the "driver" needed for coreboot
to present a TPM node in the devicetree. It would usually only do so,
if coreboot itself is communicating with the TPM via I2C (I2C_TPM).
However, technically, there is no dependency.
In order to not show the ACPI option in menuconfig if the board is not
using I2C, a dependency was declared in Kconfig. However, the same can
be achieved without making it an error to manually declare
DRIVER_I2C_TPM_ACPI without I2C_TPM.
For Volteer, we have just such a need, since it has two "sub-variants"
sharing the same overridetree.cb, one having SPI TPM and another having
I2C TPM. The former will have a disabled ACPI node representing the I2C
TPM, while its Kconfig is such that coreboot itself does not have I2C
TPM support.
In order to export even a disabled ACPI node representing the I2C
connected TPM, coreboot needs DRIVER_I2C_TPM_ACPI. Hence, that will
have to be enabled in a case where coreboot does not have I2C_TPM (for
one of the two sub-variants, namely volteer2).
BUG=b:173461736
TEST=Tested as part of next CL in chain
Change-Id: I9717f6b68afd90fbc294fbbd2a5b8d0c6ee9ae55
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48222
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Export all registers that driver is looking for. And put in alphabetic order.
The missing registers for kernel v5.4 sx93xx are:
reg_irq_msk
reg_irq_cfg0
reg_irq_cfg2
reg_afe_ph0/1/2/3
BUG=b:172397658
BRANCH=zork
TEST=Build passed
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic9d7a959b1769b6846bba302e3aeab9a3a1cedac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47866
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current location for the sensor initialization procedure was chosen
by mistake. Move this into a separate function in nct7802y.c .
Change-Id: I093ae75db5f0051bff65375b0720c86642b9148a
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Follow model of drivers/i2c/generic and use user-supplied device
name if specified in the chip config.
Change-Id: Ia783bac2797e239989c03a3421b9293a055db3d0
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47782
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DDN field isn't required, no point in writing an empty string to it.
Change-Id: Ifea6e48c324598f114178e86a79f519ee35f5258
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47781
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds a new driver for the SX9324 proximity detector device.
Follow SX9324 datasheet Rev3.
BUG=b:172397658
BRANCH=zork
TEST=Test sx9324 is working as expected.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ifd582482728a2f535ed85f6696b2f5a4529ba421
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47640
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current HID "RX6110SA" does not comply with the ACPI spec in terms
of the naming convention where the first three caracters should be a
vendor ID and the last 4 characters should be a device ID. For now
there is a vendor ID for Epson (SEC) but there is none for this
particular RTC. In order to avoid the reporting of a non ACPI-compliant
HID it will be dropped completely for now.
Once Epson has assigned a valid HID for this RTC, this valid HID will be
used here instead.
Change-Id: Ib77ffad084c25f60f79ec7d503f14731b1ebe9e2
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47706
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The CONFIG_TPM_I2C_BURST_LIMITATION was never added, so this has never
been turned on. The Kconfig linter generates three warnings about this
block:
Warning: Unknown config option CONFIG_TPM_I2C_BURST_LIMITATION
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I53fa8f5b4eac6a1e7efec23f70395058bad26299
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47367
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is a trivial patch to fix some comments that were generating
notes in the kconfig lint test.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I26a95f17e82910f50c62215be5c29780fe98e29a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47366
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When the host sends data in i2c bus, device might not send ACK. It means
that data is not processed on the device side, but for now we don't
check for that condition thus wait for the response which will not come.
Designware i2c detect such situation and set TX_ABORT bit. Checking for
the bit will enable other layers to immediately retry rather than
wait-timeout-retry cycle.
BUG=b:168838505
BRANCH=zork
TEST=test on zork devices, now we see "Tx abort detected" instead of I2C
timeout for tpm initializtion.
Change-Id: Ib0163fbce55ccc99f677dbb096f67a58d2ef2bda
Signed-off-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The defines for RX6110SA_SLAVE_ADR and RX6110SA_I2C_CONTROLLER are not
used anymore and can be deleted.
Change-Id: I3cddf7a9e2f757a22c729ae0f0ff767d55909b9c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: siemens-bot
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
This patch adds basic ACPI support for the RTC so that the OS is able to
use this RTC via the ACPI interface.
If the Linux kernel is able to find the RTC in ACPI scope, you should
see the following lines in dmesg, where [n] is an enumerated number:
rx6110 i2c-RX6110SA:00: rtc core: registered RX6110SA:00 as rtc[n]
rtc rtc[n]: Update timer was detected
Change-Id: I9b319e3088e6511592075b055f8fa3e2aedaa209
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Individual drivers check whether the concerned device is enabled before
filling in the SSDT. Move the check before calling acpi_fill_ssdt() and
remove the check in the individual drivers.
BUG=None
TEST=util/abuild/abuild
Change-Id: Ib042bec7e8c68b38fafa60a8e965d781bddcd1f0
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
This chip driver adds ACPI identifiers for multiplexed I2C bus that are
selected using GPIO. The multiplexed bus device defines the address
to select the I2C lines. These ACPI identifiers are consumed by the
i2c-mux-gpio kernel driver:
https://www.kernel.org/doc/html/latest/i2c/muxes/i2c-mux-gpio.html
BUG=b:169444894
TEST=Build and boot to OS in waddledee. Ensure that the ACPI identifiers
are added in appropriate context.
Scope (\_SB.PCI0.I2C3.MUX0)
{
Device (MXA0)
{
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Name (_ADR, Zero) // _ADR: Address
}
}
Scope (\_SB.PCI0.I2C3.MUX0)
{
Device (MXA1)
{
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Name (_ADR, One) // _ADR: Address
}
}
Change-Id: If8b983bc8ce212ce05fe6b7f01a6d9092468e582
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add identifiers in ACPI tables for GPIO based I2C multiplexer. The
multiplexer device defines the GPIO resource used to select the
adapter/bus lines. The multiplexer adapter device defines the address
to select the adapter/client lines. These ACPI identifiers are consumed
by the i2c-mux-gpio kernel driver:
https://www.kernel.org/doc/html/latest/i2c/muxes/i2c-mux-gpio.html
BUG=b:169444894
TEST=Build and boot waddledee to OS. Ensure that the ACPI identifiers
are added for I2C devices multiplexed using I2C MUX under the
appropriate scope. Here is the output SSDT:
Scope (\_SB.PCI0.I2C3)
{
Device (MUX0)
{
Name (_HID, "PRP0001") // _HID: Hardware ID
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
{
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.PCI0.GPIO", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0125
}
})
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /* Device Properties for _DSD */,
Package (0x02)
{
Package (0x02)
{
"compatible",
"i2c-mux-gpio"
},
Package (0x02)
{
"mux-gpios",
Package (0x04)
{
\_SB.PCI0.I2C3.MUX0,
Zero,
Zero,
Zero
}
}
}
})
}
}
Change-Id: Ib371108cc6043c133681066bf7bf4b2e00771e8b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The patch allows to configure sensors with a remote diode connected
and a on-chip local temperature sensor from the devicetree for the
board that uses this HWM. According to the documentation [1], this is
done by setting the corresponding bits in the Mode Selection Register
(22h). It is necessary for some Intel processors (Apollo Lake SoC)
that do not support PECI and the CPU temperature is taken from the
thermistor.
TEST = After loading the nct7802 module on the Kontron mAL-10 [2] with
Linux OS, we can see configuration of the HWM with one sensor in
the thermistor mode:
user@user-apl:~$ sensors
coretemp-isa-0000
Adapter: ISA adapter
Package id 0: +41.0°C (high = +110.0°C, crit = +110.0°C)
Core 0: +40.0°C (high = +110.0°C, crit = +110.0°C)
Core 1: +40.0°C (high = +110.0°C, crit = +110.0°C)
Core 2: +41.0°C (high = +110.0°C, crit = +110.0°C)
Core 3: +41.0°C (high = +110.0°C, crit = +110.0°C)
nct7802-i2c-0-2e
Adapter: SMBus CMI adapter cmi
in0: +3.35 V (min = +0.00 V, max = +4.09 V)
in1: +1.92 V
in3: +1.21 V (min = +0.00 V, max = +2.05 V)
in4: +1.68 V (min = +0.00 V, max = +2.05 V)
fan1: 0 RPM (min = 0 RPM)
fan2: 868 RPM (min = 0 RPM)
fan3: 0 RPM (min = 0 RPM)
temp1: +42.5°C (low = +0.0°C, high = +85.0°C)
(crit = +100.0°C) sensor = thermistor
temp4: +44.0°C (low = +0.0°C, high = +85.0°C)
(crit = +100.0°C)
temp6: +0.0°C
[1] page 30, section 7.2.32, Nuvoton Hardware Monitoring IC NCT7802Y
with PECI 3.0 interface, datasheet, revision 1.2, february 2012
[2] https://review.coreboot.org/c/coreboot/+/39133
Change-Id: I28cc4e5cae76cf0bcdad26a50ee6cd43a201d31e
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39766
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I202e5d285612b9bf237b588ea3c006187623fdc3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
This adds a missing newline to a printk in the max98373 driver.
BUG=none
TEST=verified BIOS boot log is properly formatted on volteer.
Change-Id: I1c989729bdc71736975901566023e0057a6d0556
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: Iaf22dc1986427e8aa4521b0e9b40fafa5a29dbbd
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Found using:
diff <(git grep -l '#include <stdint.h>' -- src/) <(git grep -l 'int8_t\|int16_t\|int32_t\|int64_t\|intptr_t\|intmax_t\|s8\|u8\|s16\|u16\|s32\|u32\|s64\|u64\|INT8_MIN\|INT8_MAX\|INT16_MIN\|INT16_MAX\|INT32_MIN\|INT32_MAX\|INT64_MIN\|INT64_MAX\|INTMAX_MIN\|INTMAX_MAX' -- src/) |grep -v vendorcode |grep '<'
Change-Id: I5e14bf4887c7d2644a64f4d58c6d8763eb74d2ed
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41827
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Files found using:
diff <(git grep -l '#include <types.h>' -- src/) <(git grep -l 'BIT(\|size_t\|wchar_t\|wint_t\|NULL\|DEVTREE_EARLY\|DEVTREE_CONST\|MAYBE_STATIC_NONZERO\|zeroptr\|int8_t\|int16_t\|int32_t\|int64_t\|intptr_t\|intmax_t\|s8\|u8\|s16\|u16\|s32\|u32\|s64\|u64\|INT8_MIN\|INT8_MAX\|INT16_MIN\|INT16_MAX\|INT32_MIN\|INT32_MAX\|INT64_MIN\|INT64_MAX\|INTMAX_MIN\|INTMAX_MAX\|bool\|true\|false\|cb_err\|CB_SUCCESS\|CB_ERR\|CB_ERR_ARG\|CB_CMOS_\|CB_KBD_\|CB_I2C_\|cb_err_t\|DIV_ROUND_CLOSEST\|container_of\|__unused\|alloca(\|ARRAY_SIZE\|ALIGN\|ALIGN_UP\|ALIGN_DOWN\|IS_ALIGNED\|__CMP_UNSAFE\|MIN_UNSAFE\|MAX_UNSAFE\|__CMP_SAFE\|__CMP\|MIN(\|MAX(\|ABS(\|IS_POWER_OF_2\|POWER_OF_2\|DIV_ROUND_UP\|SWAP(\|KiB\|MiB\|GiB\|KHz\|MHz\|GHz\|offsetof(\|check_member\|member_size' -- src/)|grep -v vendor |grep '<'
Change-Id: I5d99d844cc58d80acb505d98da9d3ec76319b2eb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41677
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Nothing selects this driver. Drop it before it grows moss.
Change-Id: I4d0e678a8725c1fdf9263b9fae4e4fb6bb5ab4de
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43268
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Nothing selects this driver. Drop it before it grows moss.
Change-Id: I9311dd07b8259384badec65da649fa0cf2da1e01
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43267
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per ACPI spec, GpioIo does not have any polarity associated with
it. Linux kernel uses `active_low` argument within GPIO _DSD property
to allow BIOS to indicate if the corresponding GPIO should be treated
as active low. Thus, if GPIO has active high polarity or if it does
not have any polarity associated with it, then the `active_low`
argument is supposed to be set to 0.
Having a `polarity` field in acpi_gpio seems confusing because GPIOs
might not always have polarity associated with them. Example, in case
of DMIC-select GPIO where 0 means select DMIC0 and 1 means select
DMIC1, there is no polarity associated with the GPIO. Thus, it would
be clearer for mainboard to use macros without having to specify a
particular polarity. In order to enable mainboards to provide GPIO
information without polarity for GpioIo usage, this change also adds
`ACPI_GPIO_OUTPUT` and `ACPI_GPIO_INPUT` macros.
BUG=b:157603026
Change-Id: I39d2a6ac8f149a74afeb915812fece86c9b9ad93
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
<types.h> is supposed to provide <commonlib/bsd/cb_err.h>,
<stdbool.h>,<stdint.h> and <stddef.h>. So remove those includes
each time when <types.h> is included.
Change-Id: I886f02255099f3005852a2e6095b21ca86a940ed
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Fix coreboot build error with adding this driver
BUG=b:149443429
BRANCH=None
TEST=built without errors
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Change-Id: I2d76ec72ca6ae9ac54ab05f15ea92beb645acd5c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I8a207e30a73d10fe67c0474ff11324ae99e2cec6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41360
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix coreboot build error with adding this driver
BUG=b:149443429
BRANCH=None
TEST=built without errors
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Change-Id: I46bced77a50903c16239a5162d144697e9d704a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41389
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If the device doesn't return a valid component type, that means the
device is non-functional.
The dw_i2c_regs had invalid offsets for the version field. I got the
correct value from the DesignWare DW_apb_i2c Databook v2.02a. It also
matches what the Picasso PPR says.
I also print out the version field of the controller.
BUG=b:153001807
BRANCH=none
TEST=Tested on PSP where I2C is non functional. Also tested on trembyle
and verified i2c was initialized.
Saw the following in the logs
I2C bus 2 version 0x3132322a
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If5527972508e0f4b35cc9ecdb1491b1ce85ff3af
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2144540
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40870
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
unused includes of <stdin.h> found using following commande:
diff <(git grep -l '#include <stdint.h>' -- src/) <(git grep -l
'int8_t\|uint8_t\|int16_t\|uint16_t\|int32_t\|uint32_t\|int64_t\|
uint64_t\|intptr_t\|uintptr_t\|intmax_t\|uintmax_t\|s8\|u8\|s16\|
u16\|s32\|u32\|s64\|u64\|INT8_MIN\|INT8_MAX\|UINT8_MAX\|INT16_MIN\
|INT16_MAX\|UINT16_MAX\|INT32_MIN\|INT32_MAX\|UINT32_MAX\|INT64_MIN\
|INT64_MAX\|UINT64_MAX\|INTMAX_MIN\|INTMAX_MAX\|UINTMAX_MAX' -- src/)
|grep '<' |grep -v vendor |grep -vF '.h'
Change-Id: Icb9b54c6abfb18d1e263665981968a4d7cccabeb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41148
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CB:41194 got rid of "this file is part of" lines. However, there are
some changes that landed right around the same time including those
lines. This change uses the following command to drop the lines from
new files:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ic3c1d717416f6b7e946f84748e2b260552c06a1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41342
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add an SSDT generator for Maxim 98390 kernel driver.
Copied from 'drivers/i2c/rt1011'.
BUG=b:149443429
BRANCH=None
TEST=built coreboot and checked audio function with kernel patch on nightfury
Change-Id: I64d776c6c9726eb5822ad4dd82f6826c2a30cb1d
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39463
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Used commands:
perl -i -p0e 's|\/\*[\s*]*.*is free software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and\/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-2.0-only */|' $(cat filelist)
perl -i -p0e 's|\/\*[\s*]*.*is[\s*]*free[\s*]*software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*either[\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License,[\s*]*or[\s*]*.at[\s*]*your[\s*]*option.[\s*]*any[\s*]*later[\s*]*version.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-2.0-or-later */|' $(cat filelist)
perl -i -p0e 's|\/\*[\s*]*.*is[\s*#]*free[\s*#]*software[;:,][\s*#]*you[\s*#]*can[\s*#]*redistribute[\s*#]*it[\s*#]*and/or[\s*#]*modify[\s*#]*it[\s*#]*under[\s*#]*the[\s*#]*terms[\s*#]*of[\s*#]*the[\s*#]*GNU[\s*#]*General[\s*#]*Public[\s*#]*License[\s*#]*as[\s*#]*published[\s*#]*by[\s*#]*the[\s*#]*Free[\s*#]*Software[\s*#]*Foundation[;:,][\s*#]*either[\s*#]*version[\s*#]*3[\s*#]*of[\s*#]*the[\s*#]*License[;:,][\s*#]*or[\s*#]*.at[\s*#]*your[\s*#]*option.[\s*#]*any[\s*#]*later[\s*#]*version.[\s*#]*This[\s*#]*program[\s*#]*is[\s*#]*distributed[\s*#]*in[\s*#]*the[\s*#]*hope[\s*#]*that[\s*#]*it[\s*#]*will[\s*#]*be[\s*#]*useful[;:,][\s*#]*but[\s*#]*WITHOUT[\s*#]*ANY[\s*#]*WARRANTY[;:,][\s*#]*without[\s*#]*even[\s*#]*the[\s*#]*implied[\s*#]*warranty[\s*#]*of[\s*#]*MERCHANTABILITY[\s*#]*or[\s*#]*FITNESS[\s*#]*FOR[\s*#]*A[\s*#]*PARTICULAR[\s*#]*PURPOSE.[\s*#]*See[\s*#]*the[\s*#]*GNU[\s*#]*General[\s*#]*Public[\s*#]*License[\s*#]*for[\s*#]*more[\s*#]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-3.0-or-later */|' $(cat filelist)
perl -i -p0e 's|(\#\#*)[\w]*.*is free software[:;][\#\s]*you[\#\s]*can[\#\s]*redistribute[\#\s]*it[\#\s]*and\/or[\#\s]*modify[\#\s]*it[\s\#]*under[\s \#]*the[\s\#]*terms[\s\#]*of[\s\#]*the[\s\#]*GNU[\s\#]*General[\s\#]*Public[\s\#]*License[\s\#]*as[\s\#]*published[\s\#]*by[\s\#]*the[\s\#]*Free[\s\#]*Software[\s\#]*Foundation[;,][\s\#]*version[\s\#]*2[\s\#]*of[\s\#]*the[\s\#]*License.*[\s\#]*This[\s\#]*program[\s\#]*is[\s\#]*distributed[\s\#]*in[\s\#]*the[\s\#]*hope[\s\#]*that[\s\#]*it[\s\#]*will[\#\s]*be[\#\s]*useful,[\#\s]*but[\#\s]*WITHOUT[\#\s]*ANY[\#\s]*WARRANTY;[\#\s]*without[\#\s]*even[\#\s]*the[\#\s]*implied[\#\s]*warranty[\#\s]*of[\#\s]*MERCHANTABILITY[\#\s]*or[\#\s]*FITNESS[\#\s]*FOR[\#\s]*A[\#\s]*PARTICULAR[\#\s]*PURPOSE.[\#\s]*See[\#\s]*the[\#\s]*GNU[\#\s]*General[\#\s]*Public[\#\s]*License[\#\s]*for[\#\s]*more[\#\s]*details.\s(#* *\n)*|\1 SPDX-License-Identifier: GPL-2.0-only\n\n|' $(cat filelist)
perl -i -p0e 's|(\#\#*)[\w*]*.*is free software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and\/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.\s(#* *\n)*|\1 SPDX-License-Identifier: GPL-2.0-only\n\n|' $(cat filelist)
Change-Id: Ia01908544f4b92a2e06ea621eca548e582728280
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41178
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This replaces GPLv2-or-later and GPLv2-only long form text with the
short SPDX identifiers.
Commands used:
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.*of.*the.*License.*or.*(at.*your.*option).*any.*later.*version.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-or-later */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation[.;,].+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This software is licensed under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation,.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
Change-Id: I7a746088a35633c11fc7ebe86006e96458a1abf8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
That makes it easier to identify "license only" headers (because they
are now license only)
Script line used for that:
perl -i -p0e 's|/\*.*\n.*This file is part of the coreboot project.*\n.*\*|/* This file is part of the coreboot project. */\n/*|' # ...filelist...
Change-Id: I2280b19972e37c36d8c67a67e0320296567fa4f6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 3/5 which basically is generated by
running the following command:
$ git grep -iIl "arch/acpi" | xargs sed -i 's/arch\/acpi/acpi\/acpi/g'
BUG=b:155428745
Change-Id: I16b1c45d954d6440fb9db1d3710063a47b582eae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Change-Id: I12345a5b6c9ce94ca9f8b555154b2278a8ff97bf
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
.acpi_fill_ssdt() does not need to modify the device structure. This
change makes the struct device * parameter to acpi_fill_ssdt() as
const.
Change-Id: I110f4c67c3b6671c9ac0a82e02609902a8ee5d5c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40710
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change makes the struct device * param to callback function
called by i2c_generic_fill_ssdt() as const. This is in preparation to
make struct device * param to fill_ssdt as const.
Change-Id: I7556b672a7b0172ded44747af394f5b32b6209aa
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40707
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
dw_i2c_soc_dev_to_bus() does not need to modify the device
structure. Thus, this change makes the struct device * parameter to
dw_i2c_soc_dev_to_bus as const.
Change-Id: Ibf5c8d8127dff2ab2ccbd1f6b4f553e98e81955f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40704
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When CONFIG_SEPARATE_VERSTAGE=n, all verstage code gets linked into the
appropriate calling stage (bootblock or romstage). This means that
ENV_VERSTAGE is actually 0, and instead ENV_BOOTBLOCK or ENV_ROMSTAGE
are 1. This keeps tripping up people who are just trying to write a
simple "are we in verstage (i.e. wherever the vboot init logic runs)"
check, e.g. for TPM init functions which may run in "verstage" or
ramstage depending on whether vboot is enabled. Those checks will not
work as intended for CONFIG_SEPARATE_VERSTAGE=n.
This patch renames ENV_VERSTAGE to ENV_SEPARATE_VERSTAGE to try to
clarify that this macro can really only be used to check whether code is
running in a *separate* verstage, and clue people in that they may need
to cover the linked-in verstage case as well.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I2ff3a3c3513b3db44b3cff3d93398330cd3632ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
`.read_resources` and `.set_resources` are the only two device
operations that are considered mandatory. Other function pointers
can be left NULL. Having dedicated no-op implementations for the
two mandatory fields should stop the leaking of no-op pointers to
other fields.
Change-Id: I6469a7568dc24317c95e238749d878e798b0a362
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40207
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Providing an explicit no-op function pointer is only necessary for
`.read_resources` and `.set_resources`. All other device-operation
pointers are optional and can be NULL.
Change-Id: I3d139f7be86180558cabec04b8566873062e33be
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40206
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I38eaffa391ed5971217ffad74a312b1641e431c9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
These two identifiers were always very confusing. We're not filling and
injecting generators. We are filling SSDTs and injecting into the DSDT.
So drop the `_generator` suffix. Hopefully, this also makes ACPI look a
little less scary.
Change-Id: I6f0e79632c9c855f38fe24c0186388a25990c44d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39977
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: David Guckian
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:143885765
TEST=I2C clock speed on trembyle is 400kHz
Change-Id: I50e904822823a6fc173d4d4b76f0882b4ce81ae8
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/1970655
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I89b10076e0f4a4b3acd59160fb7abe349b228321
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39611
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Move opening bracket to line above
2. Remove space after `printk` statements
Change-Id: Ia12a4ed6ab2fb2c9848a2688b41fcfa70ab001b0
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Change-Id: I84e09706aceae69671ce429d77e7874128468307
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
There is no documentation what hardware this was compatible
with.
Change-Id: I9bfada83388373962929f35794bca56132ee3d9e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
There is no documentation what hardware this was compatible
with.
Change-Id: Ie8832f1d7f4ca2bc8121f84b1ee564403cc69026
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ie72f66a8fc93e4994df5463b8ff19ba118c88389
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I8e0dbff67709841c6ae3ec6f6130805ac935f2ee
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38157
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I4e2ebe4f2a90cc27f9a4de907b873df44718234d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I254f62c9a94838f70d624dadf32cb42c2370123d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38152
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This is to remove min/max() from <stdlib.h>.
Change-Id: Ica03d9aec8a81f57709abcac655dfb0ebce3f8c6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37818
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I05422ee4b0aa5c02525ef0b4eccb4dc3ecf871e8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32822
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Iabe55bfbc8e047c0791c21d162767081a181b6c5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37411
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
'struct acpi_gpio' and 'struct acpi_irq' require the inclusion
of acpi_device.h. The only reason this wasn't caught previously
is due to the header being included with another driver compiled
first on the one board using it (google/eve).
Change-Id: I987f0ec6f769e550f3421629e0ef0c579a3d12f9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37539
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
