| Age | Commit message (Collapse) | Author |
|---|
|
These were often used to distinguish CAR_GLOBAL variables that weren't
directly usable. Since we're getting rid of this special case, also get
rid of the marker.
This change was created using coccinelle and the following script:
@match@
type T;
identifier old =~ "^(g_.*|.*_g)$";
@@
old
@script:python global_marker@
old << match.old;
new;
@@
new = old
if old[0:2] == "g_":
new = new[2:]
if new[-2:] == "_g":
new = new[:-2]
coccinelle.new = new
@@
identifier match.old, global_marker.new;
@@
- old
+ new
@@
type T;
identifier match.old, global_marker.new;
@@
- T old;
+ T new;
@@
type T;
identifier match.old, global_marker.new;
@@
- T old
+ T new
= ...;
There were some manual fixups: Some code still uses the global/local
variable naming scheme, so keep g_* there, and some variable names
weren't completely rewritten.
Change-Id: I4936ff9780a0d3ed9b8b539772bc48887f8d5eed
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Change-Id: I1c09eda6164efb390de4626f52aafba59962f9c4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37029
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Various recent x86 SOCs have trouble registering short pulses
generated by the H1 to indicate that it is ready for the next
transaction.
This patch adds an error message to report this condition, which would
greatly reduce the amount of guesswork when troubleshooting new
platforms.
BUG=b:144002424
TEST=tried this code on the Drallion device exhibiting the problem,
observed error messages in the coreboot log;
$ grep IRQ ap.log
Cr50 i2c TPM IRQ timeout!
Cr50 i2c TPM IRQ timeout!
Cr50 i2c TPM IRQ timeout!
Cr50 i2c TPM IRQ timeout!
...
Change-Id: I5f6ee3986bed58e12fd0ec8cecbf35f46c9263c2
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
This patch provides a chip driver for the DP-2-LVDS bridge PTN3460.
The bridge is configured via I2C. As the mainboard has all the
information regarding the attached LCD type, there are three hooks into
mainboard code to get the information like EDID data and PTN config.
TEST=Display is working on Siemens mainboards (e.g. mc_tcu3, mc_apl1, ...).
Change-Id: Ie4c8176cd16836fa5b8fd2f72faf7a55723b82f6
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ibb7b48a7a144421aff29acbb7ac30968ae5fe5ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Also, including <types.h>, is supposed to provide stdint and stddef.
Change-Id: I99918a5a77e759bc7d4192d2c3fd6ad493c70248
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33681
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
RT1011 is a smart amplifier. It needs to know speaker related parameters
including speaker resistor value and temperature when the calibration is
done in order to run Dynamic Speaker Management (DSM) algorithm on chip.
The purpose of DSM is to protect speaker when the volume is large.
The calibration data of speaker is stored in VPD in factory.
This driver is needed to read data from VPD and write to ACPI _DSD when
config CHROMEOS_DSM_CALIB is turned on.
Kernel rt1011 codec driver will read these device properties to set up
codec accordingly on boot.
The reason to prepare these parameters in coreboot is because kernel
codec driver expects to read per-device parameters directly from device
properties. Another benefit is that other OS can also take these
parameters through ACPI _DSD table and take benefit of DSM on RT1011.
The kernel driver device properties of RT1011 are documented at
linux/Documentation/devicetree/bindings/sound/rt1011.txt
It is currently in ASoC maintainer's tree at
https://kernel.googlesource.com/pub/scm/linux/kernel/git/broonie/sound/+/for-next/
and hopefully should be merged to mainline kernel in the next merge window.
BUG=b:140397934
BRANCH=none
TEST=On Helios, with patch series, check realtek,r0_calib and
realtek,temperature_calib are available to rt1011 codec driver.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Change-Id: I9550b9890ce2cae787f4f17779a5ade77f619171
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Updated Authors file is in a separate commit.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I1acea8c975d14904b7e486dc57a1a67480a6ee6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Allow to set a lower temperature limit, as the currently hard-coded
25C may be to low for a given temperature sensor. Also enable smoo-
thing, currently hard-coded to the maximum interval of 35s, and set
the hysteresis value.
Change-Id: I5fde1cf909e8fbbaf8a345790b00c58a73c19ef8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
We accidentally converted an `int` return value to an `unsigned`,
making it impossible to check for errors with `< 0`. Fix that by
using an `int` variable.
Change-Id: I5433c27e334bc177913e138df83118b128c674b7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The existing Kconfig code made SMBIOS_PROVIDED_BY_MOBO depend
on VENDOR_LENOVO. Thus, it couldn't be selected by boards from
other vendors. So we add another Kconfig that selects it
here.
NB. It's still unclear how the two drivers in this directory
are related (at24rf08c and lenovo_serial). From the code, it
doesn't look like the latter belongs here.
Change-Id: Iaa5c5a584f2a5e2426352ec6aa681f99a55efa49
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This change adds support for allowing devices to provide a
"compatible" property string that can be used when _HID is set to
PRP00001. This is used to allow Linux kernel drivers to match the
device to appropriate driver based on the OF-style compatible
string.
Reference:
https://www.kernel.org/doc/Documentation/acpi/enumeration.txt
BUG=b:129162037
TEST=Verified that atmel touchscreen gets enumerated correctly on
kohaku using PRP0001 and compatible string.
Change-Id: I8a306854c67ab2f056ea8774df46599ef0c55761
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
When generating entries in SSDT for DesignWare I2C controllers, only
use the speed selected in the devicetree, instead of trying all of them.
This quiets a message which looks like a bug ("dw_i2c: bad counts"),
later on in this driver when checking rise/fall times.
BUG=b:137298661
BRANCH=none
TEST=Boot and verify that I2C controllers still function, and
the nastygram message is gone.
Change-Id: I07207ec95652e8af1a42bfe31214f61a183a134e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34385
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Print I2C SAR device info so that it is available in cbmem logs.
BUG=none
BRANCH=none
TEST=Boot up and check cbmem -c can find the SAR I2C info
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia143932bb660ed2c2cea76310f11ede2b727adf4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33432
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We want to disable touch for non-touch sku. We can use
strap pin GPP_B4 to identify it is connected with touch
or not.
touch sku: GPP_B4 is low
non-touch sku: GPP_B4 is high
BUG=b:131132419
TEST=boot up and check no touch device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If6681262c25e4b01e061a8520e38905d40345509
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32438
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds support for mainboards to use GPIO IRQ instead of
IOAPIC to accomodate for cases where IOAPIC routing might not be
available for certain pads.
BUG=b:129794308
Change-Id: I3e2bb4280303cea177cc0c803d29140731e2b44a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32273
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also, extra-lines added or removed and local includes moved down.
Change-Id: I5e739233f3742fd68d537f671642bb04886e3009
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32009
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop 'include <string.h>' when it is not used and
add it when it is missing.
Also extra lines removed, or added just before local includes.
Change-Id: Iccac4dbaa2dd4144fc347af36ecfc9747da3de20
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
We were used to set the same values in the system and board tables.
We'll keep the mainboard values as defaults for the system tables,
so nothing changes unless somebody overrides the system table hooks.
Change-Id: I3c9c95a1307529c3137647a161a698a4c3daa0ae
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
LM96000 is the successor of the famous LM85.
Change-Id: Ie7df3107bffb7f8e45e71c4c1fbe4eb0a9e3cd03
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/21194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Just another hardware-monitoring chip. Only limited fan control and PECI
configuration is implemented.
Change-Id: I35ea79e12941804e398c6304a08170a776f4ca76
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch is a raw application of
find src/ -type f | xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g'
Change-Id: I6262d6d5c23cabe23c242b4f38d446b74fe16b88
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
MMIO operations are arch-agnostic so the include
path should not be arch/.
Change-Id: I0fd70f5aeca02e98e96b980c3aca0819f5c44b98
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31691
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I91158452680586ac676ea11c8589062880a31f91
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31692
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change sets default bus speed as I2C_SPEED_FAST instead of
I2C_SPEED_STANDARD when board does not provide any speed. This makes
it similar to all other i2c drivers in coreboot.
BUG=b:124403846
BRANCH=nocturne,atlas
Change-Id: I877d837eea2dfebf78ad7d97a32ee2071500625e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Added new routine cr50_i2c_probe() which ensures that communication
with the Cr50 over I2C is good prior to attempting other initialization
of the Cr50 and TPM state. This avoids a race condition when the Cr50
is first booting that it may reset it's I2C slave interface during the
first few I2C transactions initiated from coreboot.
BUG=b:120009037
BRANCH=none
TEST=Run the Cr50 factory update against Careena board. Confirm that
I2C reads are retried until the DID VID is valid. Tested against debug
Cr50 firmware that forced failure of cr50_i2c_probe() and verfied that
coreboot shows recovery screen.
Change-Id: I47c59a32378ad00336277e111e81ba8d2d63e69a
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
Change-Id: I7a99d0dcbc8ea1362a12a68fa519c49058d30a05
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add an entry to the soc_clock table for a 216MHz clock so that
the I2C controller clock is calculated correctly when the I2C
bus is used in coreboot.
This was tested by measuring the I2C clock speed on H1 I2C bus
on a sarien board in coreboot and ensuring it is ~400KHz.
Change-Id: I6c3cacdad318a5ce41bc41e3ac81385c2d4f396c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I40f8b4c7cbc55e16929b1f40d18bb5a9c19845da
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I17c4fc4e3e2eeef7c720c6a020b37d8f7a0f57a4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Now postcar is a standalone stage, add
it as target to all TPM bus drivers.
This is a required for a measured boot.
Change-Id: I758185daf3941a29883c2256b900360e112275e1
Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-on: https://review.coreboot.org/29546
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Idf10a09745756887a517da4c26db7a90a1bf9543
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Its spreading copies got out of sync. And as it is not a standard header
but used in commonlib code, it belongs into commonlib. While we are at
it, always include it via GCC's `-include` switch.
Some Windows and BSD quirk handling went into the util copies. We always
guard from redefinitions now to prevent further issues.
Change-Id: I850414e6db1d799dce71ff2dc044e6a000ad2552
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I6b40aaf5af5d114bbb0cd227dfd50b0ee19eebba
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28934
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The device tree now supports 'hidden' and the status can be found in
`struct device.hidden`. A new acpi_device_status() will return the
expected setting of STA from a `struct device`.
BUG=b:72200466
BRANCH=eve
TEST=Builds and boots properly on device eve
Change-Id: I6dc62aff63cc3cb950739398a4dcac21836c9766
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/28567
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Under some conditions, cr50_i2c_read() can return without actually reading
the TPM, which will leave access uninitialized. Set an initial value for
access, and if TPM fails to respond in time check if at least TPM was read.
This way avoids printing an uninitialized value.
BUG=b:112253891
TEST=Build and boot grunt.
Change-Id: I5ec7a99396db32971dc8485b77158d735ab1d788
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: Ib0839933f8b59f0c87cdda4e5374828bd6f1099f
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/23759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Change-Id: I9144937b72a98517cbd41c093cff7bad543b4140
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27916
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These two da7219_aad properties are optional:
- dlg,micbias-pulse-lvl : Mic bias higher voltage pulse level (mV).
[<2800>, <2900>]
- dlg,micbias-pulse-time : Mic bias higher voltage pulse duration (ms)
When the Mic Bias Higher Voltage feature is not required, firmware should
just not provide the dlg,micbias-pulse-lvl and dlg,micbias-pulse-time
properties.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
BUG=b:111700809
TEST=On grunt:
No "Invalid micbias pulse level" in dmesg
Change-Id: Ie99a8962e78c68b3f6927d0de34168f265d4efa9
Reviewed-on: https://review.coreboot.org/27613
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Akshu Agrawal <akshu.agrawal@amd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic1c9b1edd8d3206a68854107ddcbc5c51cb487c3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I85cd567a923cccd2504f351aae276b5f0d9db4de
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt Delco <delco@google.com>
Reviewed-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
i2c/alps driver implementation is an exact copy of the i2c/hid driver
with only the addition of ALPS0001_HID. This can be supported by the
i2c/hid driver using the hid field in devicetree which is what glkrvp
mainboard does. So, this change removes the i2c/alps driver which is
anyways unused.
Change-Id: I60761c384f3d800532b2b346272da7be28b77acd
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change fixes the issue reported by Coverity CID 1393576 to ensure
that config is checked for NULL before it is actually used.
Change-Id: I5f0cd2bf2437fc640f4cf8d8203a971daf1f8d17
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Enrico Granata <egranata@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This adds a new driver for the SX9310 proximity detector device.
The purpose of this is to enable the device's calibration information
to be stored in firmware, and then transferred over to the kernel
via ACPI.
This device has more than 10 individual configuration parameters,
so they would not fit in the generic driver's properties table.
Change-Id: Id8c434eec9fe2da731e142442503a12e88db2236
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/27173
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change checks to ensure that config is not NULL before it is
accessed for the first time.
Reported by: Coverity CID #1393312
Change-Id: Ic248c79783da9c2bfdf3b7f737e5963feff7558c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Name i2c device structure based on that in devicetree.cb
Now log looks like:
I2C: 01:0a (WCOM Touchscreen)
I2C: 03:13 (Realtek RT5663)
I2C: 03:39 (SSM4567 Right Speaker Amp)
I2C: 03:3a (SSM4567 Left Speaker Amp)
BUG=None
BRANCH=None
TEST=Build & boot Soraka
Change-Id: I5dbb66ab705cd8601b8b1dc94bc6ee9f181b7be2
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/26830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
* Remove 2nd software stack in pc80 drivers directory.
* Create TSPI interface for common usage.
* Refactor TSS / TIS code base.
* Add vendor tss (Cr50) directory.
* Change kconfig options for TPM to TPM1.
* Add user / board configuration with:
* MAINBOARD_HAS_*_TPM # * BUS driver
* MAINBOARD_HAS_TPM1 or MAINBOARD_HAS_TPM2
* Add kconfig TPM user selection (e.g. pluggable TPMs)
* Fix existing headers and function calls.
* Fix vboot for interface usage and antirollback mode.
Change-Id: I7ec277e82a3c20c62a0548a1a2b013e6ce8f5b3f
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/24903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Upstream Kernel side codec driver expect DT properties
to have 'maxim' prefix.
Update accordingly while filling SSDT entries.
BUG=b:79362472
TEST=dump DT properties in kerenl side and cross checked
TEST=Audio playback works with this change
Change-Id: Iaa4b14492dbb5a0087242f1485493f3192336f60
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Iedb78e24a286a51830c85724af0179995ed553be
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Non-dts based systems can pass mclk to da7219 driver by
this property.
BUG=b:74570989
TEST=Enabled clock in kernel driver using the property
Change-Id: I2e10769e5b3c6b3aa30f340fe0e88c29b87430cb
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/25919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Some touchscreens need to adhere to certain timings during the power
off sequence as well as during the power on sequence. Adding
reset_off_delay_ms, enable_off_delay_ms, and stop_off_delay_ms to
accommodate these devices.
BUG=b:78311818
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: Idb4a5dbe56eee4749d2f2b514e92c28fb2c6078f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/25882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Id13eef7f0fca0b929372490859aa4734ea7a9f23
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/25868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Iaed9c0882847511642d8eaab25e10d1ecf24bf90
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/25867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I147b3a2c79cd5e6b0e5fa3d23221a6afda8ba8f7
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/25866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Ic525c92e73097752a7c690186dc2034785cac678
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/25821
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of writing out '__attribute__((weak))' use a shorter form.
Change-Id: If418a1d55052780077febd2d8f2089021f414b91
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Remove extra tab before printk statement.
Change-Id: Id82239f74ac030f25000a08764637f6d1b52b87b
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/25295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The chip PCA9538 is a 8 bit I/O expander connected to the systems I2C
bus. Add a chip driver to support this chip.
Beside the pure chip driver two interface functions are provided to read
the state of the pins and write output values to the pins.
As the slave address of this chip is hardware configurable the function
pca9538_get_dev() is used to get the right slave address. This function
needs to be implemented in mainboard code if one needs to use the
interface functions to read and write I/O state.
Change-Id: Ic856123b4f4c8b721928ee3a2a4bb37833ea4b20
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/23748
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fixes: b8dc63bdfe ("ic2/designware: Move Intel i2c logic to shared driver")
Change-Id: Ic521a2d60b403b322ae583bb2c26da6019bf0ab0
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/23714
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allow specifying the DA7219 interrupt pin as either an Interrupt or
GpioInt.
BUG=b:72121803
TEST=(with whole patch series) Grunt Kernel discovers DA7219 on i2c0
Change-Id: I2d26731bf4c0ad590dad2c5d26c252371f415f9a
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
The designware i2c controller indicates that the slave address
shouldn't be programmed while the controller is enabled. Therefore,
switch the ordering of the slave target address and the enable.
Additionally, ensure the controller is disabled prior to the
start of the slave programming sequence.
Lastly, chunk up the i2c_msg segments at differing slave address
boundaries. That allows for simpler programming for the controller
by only doing one slave address transaction chunk at a time.
BUG=b:70232394,b:69250772
Change-Id: Iebc08e2db847cb182fad98e0ff3d799b9a64aca7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
To set address on AMD, IC_ENABLE == 0.
BUG=b:69416132
BRANCH=none
TEST=Test communication with i2c TPM on grunt and coral
Change-Id: I7faee8e11439deceab946cc82d30d274b529b90d
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/23293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Grunt (a amd-stoneyridge based platform) uses a GPIO to interface with
the tpm. This change allows devicetree entries to use a irq_gpio entry
to describe the interface with the TPM.
BUG=b:72655090
Change-Id: I08289891408d7176f68eb9c67f7a417a2448c2de
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23500
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Right now dw_i2c_get_soc_cfg() is expecting the SoC to implement
that callback for obtaining the bus config. However, we're currently
forcing another parameter of struct device so one can do the lookup.
This works for Intel-based systems since the struct device was needed
to program the BAR, etc. However, from an API standpoint, it just
complicates matters by needing to obtain the struct device. The SoC
already has knowlege of its own devices so it can get the config
itself by bus number. Therefore, remove that contraint from the API.
BUG=b:70232394
Change-Id: Id8558f5deedda0963a46a532a7bf984e168fb270
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23420
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In ramstage the device_operations are needed for the i2c designware
host controller. Move the intel/common/block/i2c implementation
into the generic driver so other platforms can take advantage of it.
BUG=b:72121803
Change-Id: Id249933fadcc016bfba00e7a6d65f56dfc220724
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Rename the following functions to ensure it's clear that the designware
i2c host controller driver is the one that these functions are
associated with:
i2c_get_soc_cfg() -> dw_i2c_get_soc_cfg()
i2c_get_soc_early_base() -> dw_i2c_get_soc_early_base()
i2c_soc_devfn_to_bus() -> dw_i2c_soc_devfn_to_bus()
i2c_soc_bus_to_devfn() -> dw_i2c_soc_bus_to_devfn()
BUG=b:72121803
Change-Id: Idb7633b45a0bb7cb7433ef5f6b154e28474a7b6d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23371
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
If one wants to implement both i2c_bus.h and i2c_simple.h APIs
the compilation unit needs to be guarded or coordinated carefully
with different compilation units. Instead, name the i2c_bus
functions with _dev such that it indicates that they operate on
struct device. One other change to allow i2c_bus.h to be built in
non-ramstage environments is to ensure DEVTREE_CONST is used for
the dev field in struct bus.
BUG=b:72121803
Change-Id: I267e27e62c95013e8ff8b0728dbe9e7b523de453
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a device driver to generate the device and required properties
into the SSDT for max98373.
TEST=verified SSDT contained relevant params
BUG=None
Change-Id: Id45f74e52855f4b19276e1d3d673d5448207ef4b
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: N, Harshapriya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/22673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
* Rename tlcl* to tss* as tpm software stack layer.
* Fix inconsistent naming.
Change-Id: I206dd6a32dbd303a6d4d987e424407ebf5c518fa
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
* Move code from src/lib and src/include into src/security/tpm
* Split TPM TSS 1.2 and 2.0
* Fix header includes
* Add a new directory structure with kconfig and makefile includes
Change-Id: Id15a9aa6bd367560318dfcfd450bf5626ea0ec2b
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
BUG=b:70232394
BRANCH=none
TEST=emerge-reef coreboot
emerge-glados
Change-Id: Idb453a4d2411163e6b4a8422310bf272eac5d379
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/22822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The Cr50 i2c driver provides separate entry points for probing and
initialization, but probing function does not really do much.
It also claims and releases locality on every coreboot stage, but
there is no need for this - locality should be definitely claimed
after reset and then it could be retained through the boot process.
On top of that the driver does not properly account for long time it
could take the Cr50 chip to come around to reset processing if TPM
reset request was posted during a lengthy TPM operation.
This patch addresses the issues as follows:
- tpm_vendor_probe() and tpm_vendor_cleanup() become noops, kept
around to conform to the expected driver API.
- tpm_vendor_init() invokes a function to process TPM reset only in
the first stage using TPM (typically verstage), the function
checks if locality is claimed and if so - waits for it to be
released, which indicates that TPM reset processing is over.
- before claiming locality check if it is already taken, and if so -
just proceed.
BRANCH=none
BUG=b:65867313, b:68729265
TEST=Verified that reef no longer hangs during EC reboot and
firmware_Cr50ClearTPMOwner (not yet merged) tests.
Change-Id: Iba8445caf1342e3a5fefcb2664b0759a1a8e84e3
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/22554
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In case the TPM is doing a long crypto operation the initial probe
could be very delayed. Rather than end up in recovery make the delay
long enough to accommodate the (current) long crypto times.
BUG=b:65867313, b:68729265
TEST=Verified that Soraka no longer hangs during EC reboot test.
Change-Id: I3bccff70e001dfc065c24be8ad34ef239a144db1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Some Siemens copyright entries incorrectly contain a dot at the end of
the line. This is fixed with this patch.
Change-Id: I8d98f9a7caad65f7d14c3c2a0de67cb636340116
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I4d6c6810b91294a7e401a4a1a446218c04c98e55
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
There's no reason to mutate the struct device when determining
the ACPI name for a device. Adjust the function pointer
signature and the respective implementations to use const
struct device.
Change-Id: If5e1f4de36a53646616581b01f47c4e86822c42e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change list adds imon and vmon slot numbers as params for
Maxim 98927 driver. These values are looked up in the kernel driver
to confiure IV feedback for audio playback on speakers.
BUG=b:36724448
TEST=After boot, the register dump for Max98927 codecs should have
imon and vmon slots numbers set in 0x1e register.
Change-Id: I21d72ba91af83782587f11018b2d1d1c8d4f676c
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/21195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There is at least one I2C device (being used by Soraka) that has 3
controls -- enable, reset and stop. If the stop gpio is not put into
the right state when turning off the device in suspend mode, then it
causes leakage. Thus, we need control in power resource to be able to
stop the device when entering suspend state.
BUG=b:64987428
TEST=Verified on soraka that touchscreen stop is correctly configured
on suspend.
Change-Id: Iae5ec7eb3972c5c7f80956d60d0d3c321bbefb0f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21249
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replaces the ics/954309 driver with a more generic version to
accommodate clockgens with a different amount of registers.
It also features a mask to only touch certain bits of the clockgen.
TODO: set appropriate mask for X60/T60 since the datasheets for their
clockgens can be found.
Change-Id: Ie43c4de7891a39f2f443e78213ecd688134e68d7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add support for providing additional free form device properties via
devicetree in order to make this driver suitable for kernel drivers
that need additional board-specific device properties.
This currently allows adding up to 10 additional properties to a device.
BUG=b:63413023
TEST=manual testing to ensure that newly added properties are in SSDT
Change-Id: I2b8ceb208f4aba01053746547def6d07c8f8f3a2
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/21270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ib31e77eec639c231520198c0b978d6c3c1eadaed
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Split `i2c.h` into three pieces to ease reuse of the generic defi-
nitions. No code is changed.
* `i2c.h` - keeps the generic definitions
* `i2c_simple.h` - holds the current, limited to one controller driver
per board, devicetree independent I2C interface
* `i2c_bus.h` - will become the devicetree compatible interface for
native I2C (e.g. non-SMBus) controllers
Change-Id: I382d45c70f9314588663e1284f264f877469c74d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Our current struct for I2C segments `i2c_seg` was close to being compa-
tible to the Linux version `i2c_msg`, close to being compatible to SMBus
and close to being readable (e.g. what was `chip` supposed to mean?) but
turned out to be hard to fix.
Instead of extending it in a backwards compatible way (and not touching
current controller drivers), replace it with a Linux source compatible
`struct i2c_msg` and patch all the drivers and users with Coccinelle.
The new `struct i2c_msg` should ease porting drivers from Linux and help
to write SMBus compatible controller drivers.
Beside integer type changes, the field `read` is replaced with a generic
field `flags` and `chip` is renamed to `slave`.
Patched with Coccinelle using the clumsy spatch below and some manual
changes:
* Nested struct initializers and one field access skipped by Coccinelle.
* Removed assumption in the code that I2C_M_RD is 1.
* In `i2c.h`, changed all occurences of `chip` to `slave`.
@@ @@
-struct i2c_seg
+struct i2c_msg
@@ identifier msg; expression e; @@
(
struct i2c_msg msg = {
- .read = 0,
+ .flags = 0,
};
|
struct i2c_msg msg = {
- .read = 1,
+ .flags = I2C_M_RD,
};
|
struct i2c_msg msg = {
- .chip = e,
+ .slave = e,
};
)
@@ struct i2c_msg msg; statement S1, S2; @@
(
-if (msg.read)
+if (msg.flags & I2C_M_RD)
S1 else S2
|
-if (msg.read)
+if (msg.flags & I2C_M_RD)
S1
)
@@ struct i2c_msg *msg; statement S1, S2; @@
(
-if (msg->read)
+if (msg->flags & I2C_M_RD)
S1 else S2
|
-if (msg->read)
+if (msg->flags & I2C_M_RD)
S1
)
@@ struct i2c_msg msg; expression e; @@
(
-msg.read = 0;
+msg.flags = 0;
|
-msg.read = 1;
+msg.flags = I2C_M_RD;
|
-msg.read = e;
+msg.flags = e ? I2C_M_RD : 0;
|
-!!(msg.read)
+(msg.flags & I2C_M_RD)
|
-(msg.read)
+(msg.flags & I2C_M_RD)
)
@@ struct i2c_msg *msg; expression e; @@
(
-msg->read = 0;
+msg->flags = 0;
|
-msg->read = 1;
+msg->flags = I2C_M_RD;
|
-msg->read = e;
+msg->flags = e ? I2C_M_RD : 0;
|
-!!(msg->read)
+(msg->flags & I2C_M_RD)
|
-(msg->read)
+(msg->flags & I2C_M_RD)
)
@@ struct i2c_msg msg; @@
-msg.chip
+msg.slave
@@ struct i2c_msg *msg; expression e; @@
-msg[e].chip
+msg[e].slave
@ slave disable ptr_to_array @ struct i2c_msg *msg; @@
-msg->chip
+msg->slave
Change-Id: Ifd7cabf0a18ffd7a1def25d1d7059b713d0b7ea9
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This commit adds a new driver for the RT5663 codec to use instead
of the generic i2c driver. Since the kernel needs additional
driver-specific device properties we need a BIOS driver that can
provide those properties.
The kernel driver devicetree properties for this codec are at:
linux/Documentation/devicetree/bindings/sound/rt5663.txt
This was tested by booting and verifying the generated SSDT
contains the expected device properties in _DSD.
Scope (\_SB.PCI0.I2C4)
{
Device (RT53)
{
Name (_HID, "10EC5663")
Name (_UID, Zero)
Name (_DDN, "Realtek RT5663 Codec")
Method (_STA, 0, NotSerialized)
{
Return (0x0F)
}
Name (_CRS, ResourceTemplate ()
{
I2cSerialBus (0x0013, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C4",
0x00, ResourceConsumer)
GpioInt (Edge, ActiveBoth, Exclusive, PullDefault, 0x0000,
"\\_SB.PCI0.GPIO", 0x00, ResourceConsumer)
{
0x0051
}
})
Name (_DSD, Package (0x02)
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301")
Package (0x05)
{
Package (0x02)
{
"irq-gpios",
Package (0x04)
{
\_SB.PCI0.I2C4.RT53,
Zero,
Zero,
Zero
}
},
Package (0x02)
{
"realtek,dc_offset_l_manual",
0x00FFD160
},
Package (0x02)
{
"realtek,dc_offset_r_manual",
0x00FFD1C0
},
Package (0x02)
{
"realtek,dc_offset_l_manual_mic",
0x00FF8A10
},
Package (0x02)
{
"realtek,dc_offset_r_manual_mic",
0x00FF8AB0
}
}
})
}
}
Change-Id: I3425fcbe13c9a5987fc91086d283a86db55c0819
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Ensure that the VLF bit will be cleared after a power loss event even if
the stopwatch has expired before the code to clear the bit is reached.
Change-Id: Ib2cfdabf4cd4df834395d6a102c6ae70568e71db
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
This excludes files which are mostly spaces, which I felt should be
handled separately.
Change-Id: I33043a3090e2fc6e9d2fd81e8a5e46fb6cb0aa35
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Also unify __attribute__ ((..)) to __attribute__((..)) and
handle ((__packed__)) like ((packed))
Change-Id: Ie60a51c3fa92b5009724a5b7c2932e361bf3490c
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/15921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
According to the datasheet the RTC needs a power rising slope of no more
than 100µs/V to ensure a correct power-on reset. If the mainboard that
hosts the RTC cannot guarantee this, a software reset sequence is needed
in the case where the battery was drained completely.
As the rising slope of the power supply depends on so many parameters
and is highly mainboard specific, refactor the initialization code to
perform a software reset every time a power loss event is recognized by
the RTC.
Change-Id: If64d672e51667523058041bd00e1e50ac047143d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The RTC RX6110SA has several configuration options which might be
interesting to set. To make this setup independent of the driver itself
but let it still be configurable on mainboard level, add more
configuration options to the chip driver.
Change-Id: I7f8b2aa7cd001a887f271be36f655e10e60e778b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The driver for the RTC RX6110SA is designed to be used with I2C bus.
This patch adds the possibility to use SMBus operations to access the
RTC. For this purpose the Kconfig switch RX6110SA_USE_SMBUS is added. It
is not enabled per default so that I2C will be used. One can set this
switch on board level to use SMBus instead.
Change-Id: I4827ae2c544e8002399d94a1159acacd8176c5e9
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19978
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This driver enables the usage of the external RTC chip RX6110 SA
(http://www5.epsondevice.com/en/products/i2c/rx6110sab.html) which is
connected to the I2C bus. The I2C address of this device is fixed. One
can change parameters in the device tree so that the used setup can be
adapted to match the configuration of the device on the mainboard.
Change-Id: I1290a10c2d5ad76a317c99c8b92a013309a605d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The vendor.irq field was originally intended for use as the TPM 1.2
"command complete" interrupt. However, all actual coreboot tpm drivers
and hardware use the vendor.status method of checking command completion
instead, and this irq field is not used.
Let's just remove this unused functionality to simplify the code.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
Change-Id: I994c5bfbd18124af9cb81d9684117af766ab0124
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19396
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The Cr50 TPM uses an IRQ to provide a "status" signal used for hand-shaking
the reception of commands. Real IRQs are not supported in firmware,
however firmware can still poll interrupt status registers for the same
effect.
Commit 94cc485338a3 ("drivers/i2c/tpm/cr50: Support interrupts for status")
added support for the Cr50 driver on X86 platforms to use a KConfig file
to supply an IRQ which it would poll using acpi_get_gpe. If the IRQ is
not supplied, the Cr50 driver inserts a 20 ms wait.
Unfortunately this doesn't work so well when using the i2c connected Cr50
on ARM platforms. Luckily, a more generic implementation to allow a
mainboard to supply a Cr50 IRQ status polling function was solved for SPI
connected Cr50s by commit 19e3d335bddb ("drivers/spi/tpm: using tpm irq to
sync tpm transaction").
Let's refactor the i2c c50 driver to use this same approach, and change
eve and reef boards to make use of DRIVER_TPM_TIS_ACPI_INTERRUPT for
specifying the TPM flow control interrupt.
This essentially reverts these two commits:
48f708d199 drivers/i2c/tpm/cr50: Initialize IRQ status handler before probe
94cc485338 drivers/i2c/tpm/cr50: Support interrupts for status
And ports this commit to i2c/tpm/cr50:
19e3d335bd drivers/spi/tpm: using tpm irq to sync tpm transaction
As a side effect the tpm_vendor_specific IRQ field goes back to its
original usage as the "TPM 1.2 command complete" interrupt, instead of
being repurposed to hold the flow control IRQ.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
Change-Id: I004329eae1d8aabda51c46b8504bf210484782b4
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19363
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Depend on I2C_TPM to prevent showing the menu entry on systems
that do not have an I2C TPM installed.
Change-Id: I7cd647c9c7e9721eab96ab64b844a882f156ee68
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19374
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
1. Move common TIS macros to include/tpm.h.
2. Use common TIS macros while referring to status and access registers.
3. Add a new function claim_locality to properly check for required
access bits and claim locality 0.
BUG=b:36873582
Change-Id: I11bf3e8b6e1f50b7868c9fe4394a858488367287
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19213
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The tis.c module is needlessly copying data to/from a 1260 byte
buffer on the stack. Each device's transport implementation (cr50.c
or tpm.c) maintains its own buffer, if needed, for framing purposes.
Therefore, remove the duplicated buffer.
BUG=b:36598499
Change-Id: I478fb57cb65509b5d74bdd871f1a231f8080bc2f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19061
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
The 'ordinal' variable is not used. Remove it.
BUG=b:36598499
Change-Id: I015a6633c0951980658b3c879e48bc84d604d62e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19060
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
There are unused structures/types in the tpm.h header file.
Remove them.
BUG=b:36598499
Change-Id: Iddc147640dcec70e80791846eb46298de1070672
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19059
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
In builds without CONFIG_VBOOT_SEPARATE_VERSTAGE, verstage files are
linked directly into the bootblock or the romstage. However, they're
still compiled with a separate "libverstage" source file class, linked
into an intermediate library and then linked into the final destination
stage.
There is no obvious benefit to doing it this way and it's unclear why it
was chosen in the first place... there are, however, obvious
disadvantages: it can result in code that is used by both libverstage
and the host stage to occur twice in the output binary. It also means
that libverstage files have their separate compiler flags that are not
necessarily aligned with the host stage, which can lead to weird effects
like <rules.h> macros not being set the way you would expect. In fact,
VBOOT_STARTS_IN_ROMSTAGE configurations are currently broken on x86
because their libverstage code that gets compiled into the romstage sets
ENV_VERSTAGE, but CAR migration code expects all ENV_VERSTAGE code to
run pre-migration.
This patch resolves these problems by removing the separate library.
There is no more difference between the 'verstage' and 'libverstage'
classes, and the source files added to them are just treated the same
way a bootblock or romstage source files in configurations where the
verstage is linked into either of these respective stages (allowing for
the normal object code deduplication and causing those files to be
compiled with the same flags as the host stage's files).
Tested this whole series by booting a Kevin, an Elm (both with and
without SEPARATE_VERSTAGE) and a Falco in normal and recovery mode.
Change-Id: I6bb84a9bf1cd54f2e02ca1f665740a9c88d88df4
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18302
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add support for using GPIO IRQ instead of PIRQ with an I2C device.
This allows a device to use an edge triggered interrupt that will
trigger on both high and low transitions.
The _DSD method for describing these GPIOs has a field for 'active
low' which is supposed to be 1 if the pin is active low, otherwise
is zero. The value in here doesn't mean too much for GpioInt() as
those will end up using the value from GpioInt() when it actually
requests the interrupt.
BUG=b:35581264
BRANCH=none
TEST=test on Eve board that codec IRQ can be delcared as GPIO IRQ
Change-Id: I02c64c7fc28dc2d608ad40db889c7242892f16db
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18835
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
