| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: I7c9c938bd20d36be8fdfb0d95bb58a7259650693
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
tis_plat_irq_status() function is used only by Google TPM. It should
be moved to drivers/tpm/cr50.c. The name of the function was changed
to cr50_plat_irq_status().
BUG=b:277787305
TEST=Build all affected platforms
Change-Id: I78dc39f2c7b44232b06947d3dfe6afa52807ced8
Signed-off-by: Grzegorz Bernacki <bernacki@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75917
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
In commit e59f18bf29a8 ("drivers/i2c: Add PI7C9X2G608GP PCIe switch
driver (pi608gp)"), there were some suggestions after it's been already
merged.
This patch addresses the points regarding the code style and comments.
BUG=none
TEST=Build OK, no behavioral changes in the pi608gp driver, console logs
without changes.
Change-Id: I5fc54708e0085fea4bd1f2fbf2afb400d2ccbd46
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
In commit e59f18bf29a8 ("drivers/i2c: Add PI7C9X2G608GP PCIe switch
driver (pi608gp)"), there were some suggestions after it's been already
merged.
This patch addresses the points regarding the number types - fix of the
printk format strings, inclusion of 'stdint.h' and marking the set of
allowed values as constant.
BUG=none
TEST=Build OK, no behavioral changes in the pi608gp driver, console logs
without changes.
Change-Id: I34c664f6a8a257b260facdbf9043825ff4a4c932
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75500
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
"extern" is automatically implied with function declaration.
Change-Id: Ic40218acab5a009621b6882faacfcac800aaf0b9
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71890
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
This patch adds some of the variety of configuration options exported
by the Pericom Inc. PI7C9X2G608GP PCIe switch over its SMBus interface.
Currently implemented options are only used to adjust the switch
upstream port amplitude and de-emphasis levels in millivolts. Only
values specified in the switch datasheet (in tables 6-6 and 6-8) are
allowed.
Example of a devicetree.cb entry:
chip drivers/i2c/pi608gp
register "gen2_3p5_enable" = "true"
register "gen2_3p5_amp" = "AMP_LVL_MV(425)"
register "gen2_3p5_deemph" = \
"DEEMPH_LVL_MV(37, 5)"
device i2c 0x6f on
ops pi608gp_ops
end
end
Link to the datasheet:
https://web.archive.org/web/20210225074853/https://www.diodes.com/assets/Datasheets/PI7C9X2G608GP.pdf
BUG=none
TEST=Create devicetree.cb and Kconfig entries for this driver
in a mainboard containing the switch and verify, that the values read
out from the switch config space match the values programmed over the
SMBus.
Change-Id: Id191c4e97b99da58efd3ba38bf8cca3603ece4d5
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
DSM (Dynamic Speaker Management) uses calibration parameters stored in
a VPD (Vital Product Data) FMAP region to configure the audio output
via an ACPI _DSD table. This has no dependency on a ChromeOS, and can
be used by Linux/Windows drivers if appropriately configured.
Remove the dependency of DSM_CALIB (and the calibration file) on
CHROMEOS and replace it with VPD, so that non-CHROMEOS builds
can utilize this feature as well. Move files from underneath
vc/google/chromeos to underscore the point.
TEST=build/boot google/nightfury, dump ACPI, verify DSM calibraton
parameters present in _DSD table.
Change-Id: I643b3581bcc662befc9e30736dae806f94b055af
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74812
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Only expand these strings in lib/identity.o.
Change-Id: I8732bbeff8cf8a757bf32fdb615b1d0f97584585
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Some of the chip.h files in the tree are missing the include guards.
This patch adds them in order to avoid potential redefinions of symbols
contained in these headers, when they are included multiple times in
static.c generated by sconfig.
Change-Id: I550a514e72a8dd4db602e7ceffccd81aa36446e3
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
As discused earlier, the callback name 'mb_adjust_cfg' was considered
too generic. The new naming is chosen to be consistent with other
drivers' callback names designed to be used at mainboard level.
Also other functions, namely 'mb_get_edid' and 'mb_select_edid_table'
are renamed accordingly.
BUG=none
TEST=Builds for siemens/mc_apl{1,4,5,7} and siemens/mc_ehl boards
complete successfully.
Change-Id: I4cbec0e72e5f03e94df0faa36765d1a6cd873a7a
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Allows Windows/Linux driver to use the proper jack eject debounce time.
Credit to coolstar for identifying the issue.
Change-Id: I32b94b9285f7c85ff1d67b3d78c845835bbf90d7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Contents of the EDID are passed by a reference to an array
of length 0x80, for which the macro 'PTN_EDID_LEN' has already
been around.
This patch makes use of this macro within the driver and mainboard
implementation utilizing it.
BUG=none
TEST=A successful build of mc_apl{1,4,5,7} and mc_ehl3 mainboards.
Change-Id: If7d254aaf45d717133bb426bd08f8f9fe5c05962
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Return generic coreboot error codes from the mb_adjust_cfg
callback used in mainboards instead of '-1' constant and
a driver-specific success-indicating define.
BUG=none
TEST=Boards siemens/mc_apl{1,4,5,7} and siemens/mc_ehl3
build correctly.
Change-Id: I5e0d4e67703db518ed239a845f43047f569b94ec
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Exposing the GPIOs via an ACPI PowerResource and the _CRS results in the
OS driver and ACPI thinking they own the GPIO. This can cause timing
problems because it's not clear which system should be controlling the
GPIO.
Previously, we flagged as an error any device which set the
'has_power_resource' flag but did not set 'disable_gpio_export_in_crs.'
There's no reason to require explicit disablement however, so drop the
superfluous 'disable' flag, and change the _CRS generation to check if
the GPIOs will be exported via the 'has_power_resource' flag instead.
BUG=b:265055477
TEST=build/boot skyrim, dump SSDT and verify touchscreen GPIOs only
listed under PRx, not under _CRS.
Change-Id: I837ae6c6fe4b8e1c4e10686406cba06bdb7759d2
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Change-Id: I435837381a966b61081d023447a6e7fdfd9a9348
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This reverts commit d43154486d27323f64334203e9bc8baf08af6845.
From CB:68991: This causes CraterLake boot up process to die.
Investigation in progress.
Change-Id: I4a6c11b0e638a891108fe230bdaea92d5fbca020
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: siemens-bot
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
When PTN3460_EARLY_INIT is selected, the PTN3460 (DP-2-LVDS-bridge) will
be initialized before all devices are initialized. This is necessary to
get a valid EDID data set into the PTN3460 before the graphic controller
is initialized in order to be able to show a splash screen.
For ptn3460_init() to work properly the I2C bus this bridge is connected
to needs to be initialized. As this I2C bus initialization would be done
too late in the normal flow, it needs to be called here explicitly
before ptn3460_init() to initialize the I2C bus with the needed
conditions. Otherwise the default I2C settings of the controller will be
used which results in a clock rate too high for this mainboard.
Test=Measure I2C bus signals and make sure that the clock is <= 400 kHz.
Change-Id: I1775fb7c2d29f765224d0e7c7ff9fcd4dbf847c5
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71226
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Init was always followed by open and after successful initialization we
need only send-receive function, which is now returned by tis_probe on
success further reducing number of functions to export from drivers.
Change-Id: Ib4ce35ada24e3959ea1a518c29d431b4ae123809
Ticket: https://ticket.coreboot.org/issues/433
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68991
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move `locality` field to `struct tpm_inf_dev` and put the rest directly
into `tpm_chip`.
Change-Id: Ic3644290963aca9f8dc7cd8ef754352865ef8d2c
Ticket: https://ticket.coreboot.org/issues/433
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
dw_i2c_transfer returns an enum cb_err type, but dw_i2c_dev_transfer
returns an int, so explicitly translate between the types. Since
dw_i2c_transfer only returns either CB_SUCCESS or CB_ERR which are
defined as 0 and -1, this won't change behavior of dw_i2c_dev_transfer.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iaf2cbcf6564035d5c0fc13f5d5e7ac0d0425e85d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
dw_i2c_soc_dev_to_bus will return -1 if it failed to find an I2C bus
number for a device. In this case return -1 instead of implicitly
casting the -1 to an unsigned int and passing that as bus number to
dw_i2c_transfer. The dw_i2c_base_address call inside _dw_i2c_transfer
already ended up handling this error case correctly, but better handle
the error more directly.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I06b6005cee0c5c43855cb5b388a9911fc286c984
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This function was never called from outside of drivers and
src/drivers/pc80/tpm/tis.c was the only one doing it in a questionable
way.
tpm_vendor_cleanup() also isn't needed as one of tis_close() functions
was its only caller.
Change-Id: I9df76adfc21fca9fa1d1af7c40635ec0684ceb0f
Ticket: https://ticket.coreboot.org/issues/433
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: I16689da893b5a0c3254364759d435281cb3e1caf
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69803
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is a note about the default I2C speed of this being 400 kHz
despite the logic in rx6110sa.c sets the fallback (correctly) to
100 kHz.
This information originally comes from the fact the dw_i2c bus
controller default speed is 400 kHz. This is irrelevant to
the default speed of this device as it can be used with any
bus controller.
BUG=none
TEST=coreboot builds correctly (no functional changes).
Change-Id: Ic0ffe5667574c59e1c1df952b84b8a3680b53341
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69545
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set the logging message prefix to the device name instead of the
device path in order to make the output consistent with other
logging messages in this and other drivers.
Change-Id: Ib63b93d52aad220d17f1f4ee0d47a949933ec26d
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69718
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Add ACPI generation callback to the driver after obtaining the
ACPI HID "MCRY3028" for this device from Microcrystal AG (VID: "MCRY").
Also add I2C bus speed field to the device config structure, which
is a required ACPI entry.
BUG=none
TEST=Disassemble the SSDT table and see whether the device entry
"MC28" is generated correctly. Also check whether the RV3028 driver
in Linux (drivers/rtc/rtc-rv-3028.c) is bound correctly after adding
an ACPI match table to it containing the HID. A proper kernel patch
is pending.
Change-Id: I3b8cf5c8dc551439755992ff05b6693e91cc3f21
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
There are SoCs (for instance Intel Elkhart Lake) that do use 100 MHz as
the base clock for I2C controllers. To support them properly add a
frequency setting for 100 MHz to the designware I2C controller driver.
Change-Id: I9ea11c6a41fd3758b771a416251e108cbe722769
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
SX9324 driver is updated per Linux's documentation found at
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml
Supporting logic for the deprecated SX932x driver is hence guarded by
DRIVERS_I2C_SX9324_SUPPORT_LEGACY_LINUX_DRIVER
This patch by itself does not introduce functional changes to any board.
The legacy SX932x Linux driver never reached upstream Linux and is only
available in ChromeOS kernel fork of 4.4 and 5.4. Linux later accepted
a different implementation named SX9324 and has been available since
5.4. Ideally all variants should adopt the new driver; however, during
the transition phase, coreboot must support both drivers. It is better
to have a single firmware build that can work with both Linux kernel
drivers by specifying both sets of properties. Legacy driver support
should be deleted once all variants finish migration.
BUG=b:242662878
TEST=Dump ACPI SSDT then verify _DSD entries related to the legacy
SX932x driver are identical w/ and w/o this patch
(Tested on Craask and Nivviks)
Change-Id: I42cd6841c3a270c242ed2e739db245e858eadb3b
Signed-off-by: Victor Ding <victording@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69192
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Exposing the GPIOs via an ACPI PowerResource and the _CRS results in the
OS driver and ACPI thinking they own the GPIO. This can cause timing
problems because it's not clear which system should be controlling the
GPIO. I'm making this an error because we should really clean these up.
BUG=b:210694108
TEST=Boot guybrush and see error:
> I2C: 02:5d: ERROR: Exposing GPIOs in Power Resource and _CRS
> \_SB.I2C1.H05D: Goodix Touchscreen at I2C: 02:5d
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ifcc42ed81fff295fb168a0b343e96b3a650b1c84
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
- drop ERROR prefix since already provided by cbmem log
- make error text more clear about cause of error
BUG=none
Change-Id: I1795aee240a5383b21108c697e930a2e4972a0b4
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69062
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create Kconfig options and boot state machine callback in ramstage for
an early initialization of the PTN3460 DP-to-LVDS bridge. This allows
showing the bootsplash screen on mainboards utilizing this chip during
the PCI device enumeration.
BUG=none
TEST=Select PTN3460_EARLY_INIT config switch in mainboard Kconfig and
check the log for "Attempting PTN3460 early init" message. If the
board (e.g. siemens/mc_apl7 in this case) is also configured for
showing the bootsplash logo, it should be now visible.
Change-Id: I5424d062b3fb63c78cfced3971376353be11c504
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67681
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a property to control the driving of ADCOUT.
BUG=b:234789689
TEST= build passed.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ibbedd5838a795ee645a5458b960062c5530ff3b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Since mono_time is now 64-bit, the utility functions interfacing with
mono_time should also be 64-bit so precision isn't lost.
Fixed build errors related to printing the now int64_t result of
stopwatch_duration_[m|u]secs in various places.
BUG=b:237082996
BRANCH=All
TEST=Boot dewatt
Change-Id: I169588f5e14285557f2d03270f58f4c07c0154d5
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
This patch adds a driver for a new RTC from Micro Crystal. Supported
features are:
* configure backup voltage switchover via devicetree
* configure backup capacitor charging mode via devicetree
* set date if a voltage drop on backup voltage was detected
to either a user definable (devicetree) or coreboot build date
Change-Id: I37176ea726e50e4e74d409488981d7618ecff8bb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Add MAX98396 support.
BUG=b:232606045
TEST=build passed.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I835b51ea1fcc9363992d43a625f80cb545802fc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This adds SPDX identifiers to the remaining source files in the
drivers directory that don't already have them.
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: I97f96de857515214069c3b77f3c781f7f0555c6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66499
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The check was recently removed to allow callers to pass `count == 0`.
Dereferencing the `msg` array is invalid in that case, though. Linux,
where we borrowed the i2c interface from, also treats this with -EINVAL.
Change-Id: I1eec02dd3a3fcf2d477a62cc65292fca40e469d3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
|
|
Change-Id: Ic1b38e93d919c1286a8d130700a4a2bfd6b55258
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
The current 10ms timeout for SPI TPM IRQ is not enough for platforms
using ti50 (such as corsola). Therefore, introduce a new Kconfig option
'GOOGLE_TPM_IRQ_TIMEOUT_MS'.
For platforms using cr50, we need to support legacy pre-ready-IRQ cr50
factory images during the initial boot, so the timeout remains 100ms for
I2C TPM and 10ms for SPI TPM. For all the other platforms using ti50,
the default timeout is increased to 750ms, as suggested by the ti50 team
(apronin@google.com).
BUG=b:232327704
TEST=emerge-corsola coreboot
BRANCH=none
Change-Id: I8dbb919e4a421a99a994913613a33738a49f5956
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add 'detect' flag which can be attached to devices which may or may not
be present at runtime, and for which coreboot should probe the i2c bus
to confirm device presence prior to adding an entry for it in the SSDT.
This is useful for boards which may utilize touchpads/touchscreens from
multiple vendors, so that only the device(s) present are added to the
SSDT. This relieves the burden from the OS to detect/probe if a device
is actually present and allows the OS to trust the ACPI _STA value.
Change-Id: I1a4169ed6416d544773a37d29cdcc154d3c28519
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@tutanota.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
0-byte writes can be used as a way to probe/check presence of an i2c
device, so adjust _dw_i2c_transfer() to immediately set the STOP bit
and raise logger level for TX abort messages when the segment length
is zero. Adjust dw_i2c_transfer() to allow zero-segment-length
messages to be passed thru to _dw_i2c_transfer().
Tested as part of entire i2c-detect patch train.
Change-Id: I518e849f4c476c264a1464886b1853af66c0b29d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@tutanota.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BUG=b:207333035
BRANCH=none
TEST=built and verified speaker
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Change-Id: I0dd39760dc5f44f46838c07d2e52946edc2a6d7e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64638
Reviewed-by: Vitaly Rodionov <vitaly.rodionov@cirrus.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A new iteration of Google's TPM implementation will advertize a new
DID:VID, but otherwise follow the same protocol as the earlier design.
This change makes use of Kconfigs TPM_GOOGLE_CR50 and TPM_GOOGLE_TI50
to be able to take slightly different code paths, when e.g. evaluating
whether TPM firmware is new enough to support certain features.
Change-Id: I1e1f8eb9b94fc2d5689656335dc1135b47880986
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Found using:
diff <(git grep -l '#include <acpi/acpi.h>' -- src/) <(git grep -l 'SLP_EN\|SLP_TYP_SHIFT\|SLP_TYP\|SLP_TYP_S\|ACPI_TABLE_CREATOR\|OEM_ID\|ACPI_DSDT_REV_\|acpi_device_sleep_states\|ACPI_DEVICE_SLEEP\|RSDP_SIG\|ASLC\|ACPI_NAME_BUFFER_SIZE\|COREBOOT_ACPI_ID\|acpi_tables\|acpi_rsdp\|acpi_gen_regaddr\|ACPI_ADDRESS_SPACE\|ACPI_FFIXEDHW_\|ACPI_ACCESS_SIZE_\|ACPI_REG_MSR\|ACPI_REG_UNSUPPORTED\|ACPI_HID_\|acpi_table_header\|MAX_ACPI_TABLES\|acpi_rsdt\|acpi_xsdt\|acpi_hpet\|acpi_mcfg\|acpi_tcpa\|acpi_tpm2\|acpi_mcfg_mmconfig\|acpi_hmat\|acpi_hmat_mpda\|acpi_hmat_sllbi\|acpi_hmat_msci\|acpi_srat\|ACPI_SRAT_STRUCTURE_\|acpi_srat_lapic\|acpi_srat_mem\|acpi_srat_gia\|CPI_SRAT_GIA_DEV_HANDLE_\|acpi_slit\|acpi_madt\|acpi_lpit\|acpi_lpi_flags\|acpi_lpi_desc_type\|ACPI_LPI_DESC_TYPE_\|acpi_lpi_desc_hdr\|ACPI_LPIT_CTR_FREQ_TSC\|acpi_lpi_desc_ncst\|acpi_vfct_image_hdr\|acpi_vfct\|acpi_ivrs_info\|acpi_ivrs_ivhd\|acpi_ivrs\|acpi_crat_header\|ivhd11_iommu_attr\|acpi_ivrs_ivhd_11\|dev_scope_type\|SCOPE_PCI_\|SCOPE_IOAPIC\|SCOPE_MSI_HPET\|SCOPE_ACPI_NAMESPACE_DEVICE\|dev_scope\|dmar_type\|DMAR_\|DRHD_INCLUDE_PCI_ALL\|ATC_REQUIRED\|DMA_CTRL_PLATFORM_OPT_IN_FLAG\|dmar_entry\|dmar_rmrr_entry\|dmar_atsr_entry\|dmar_rhsa_entry\|dmar_andd_entry\|dmar_satc_entry\|acpi_dmar\|acpi_apic_types\|LOCAL_APIC,\|IO_APIC\|IRQ_SOURCE_OVERRIDE\|NMI_TYPE\|LOCAL_APIC_NMI\|LAPIC_ADDRESS_\|IO_SAPIC\|LOCAL_SAPIC\|PLATFORM_IRQ_SOURCES\|LOCAL_X2APIC\|GICC\|GICD\|GIC_MSI_FRAME\|GICR\|GIC_ITS\|acpi_madt_lapic\|acpi_madt_lapic_nmi\|ACPI_MADT_LAPIC_NMI_ALL_PROCESSORS\|acpi_madt_ioapic\|acpi_madt_irqoverride\|acpi_madt_lx2apic\|acpi_madt_lx2apic_nmi\|ACPI_DBG2_PORT_\|acpi_dbg2_header\|acpi_dbg2_device\|acpi_fadt\|ACPI_FADT_\|PM_UNSPECIFIED\|PM_DESKTOP\|PM_MOBILE\|PM_WORKSTATION\|PM_ENTERPRISE_SERVER\|PM_SOHO_SERVER\|PM_APPLIANCE_PC\|PM_PERFORMANCE_SERVER\|PM_TABLET\|acpi_facs\|ACPI_FACS_\|acpi_ecdt\|acpi_hest\|acpi_hest_esd\|acpi_hest_hen\|acpi_bert\|acpi_hest_generic_data\|acpi_hest_generic_data_v300\|HEST_GENERIC_ENTRY_V300\|ACPI_GENERROR_\|acpi_generic_error_status\|GENERIC_ERR_STS_\|acpi_cstate\|acpi_sw_pstate\|acpi_xpss_sw_pstate\|acpi_tstate\|acpi_lpi_state_flags\|ACPI_LPI_STATE_\|acpi_lpi_state\|acpi_upc_type\|UPC_TYPE_\|acpi_ipmi_interface_type\|IPMI_INTERFACE_\|ACPI_IPMI_\|acpi_spmi\|ACPI_EINJ_\|ACTION_COUNT\|BEGIN_INJECT_OP\|GET_TRIGGER_ACTION_TABLE\|SET_ERROR_TYPE\|GET_ERROR_TYPE\|END_INJECT_OP\|EXECUTE_INJECT_OP\|CHECK_BUSY_STATUS\|GET_CMD_STATUS\|SET_ERROR_TYPE_WITH_ADDRESS\|TRIGGER_ERROR\|READ_REGISTER\|READ_REGISTER_VALUE\|WRITE_REGISTER\|WRITE_REGISTER_VALUE\|NO_OP\|acpi_gen_regaddr1\|acpi_einj_action_table\|acpi_injection_header\|acpi_einj_trigger_table\|set_error_type\|EINJ_PARAM_NUM\|acpi_einj_smi\|EINJ_DEF_TRIGGER_PORT\|FLAG_PRESERVE\|FLAG_IGNORE\|EINJ_REG_MEMORY\|EINJ_REG_IO\|acpi_einj\|acpi_create_einj\|fw_cfg_acpi_tables\|preload_acpi_dsdt\|write_acpi_tables\|acpi_fill_madt\|acpi_fill_ivrs_ioapic\|acpi_create_ssdt_generator\|acpi_write_bert\|acpi_create_fadt\|acpi_fill_fadt\|arch_fill_fadt\|soc_fill_fadt\|mainboard_fill_fadt\|acpi_fill_gnvs\|acpi_fill_cnvs\|update_ssdt\|update_ssdtx\|acpi_fill_lpit\|acpi_checksum\|acpi_add_table\|acpi_create_madt_lapic\|acpi_create_madt_ioapic\|acpi_create_madt_irqoverride\|acpi_create_madt_lapic_nmi\|acpi_create_madt\|acpi_create_madt_lapics\|acpi_create_madt_lapic_nmis\|acpi_create_madt_lx2apic\|acpi_create_srat_lapic\|acpi_create_srat_mem\|acpi_create_srat_gia_pci\|acpi_create_mcfg_mmconfig\|acpi_create_srat_lapics\|acpi_create_srat\|acpi_create_slit\|acpi_create_hmat_mpda\|acpi_create_hmat\|acpi_create_vfct\|acpi_create_ipmi\|acpi_create_ivrs\|acpi_create_crat\|acpi_create_hpet\|acpi_write_hpet\|generate_cpu_entries\|acpi_create_mcfg\|acpi_create_facs\|acpi_create_dbg2\|acpi_write_dbg2_pci_uart\|acpi_create_dmar\|acpi_create_dmar_drhd\|acpi_create_dmar_rmrr\|acpi_create_dmar_atsr\|acpi_create_dmar_rhsa\|acpi_create_dmar_andd\|acpi_create_dmar_satc\|cpi_dmar_\|acpi_create_\|acpi_write_hest\|acpi_soc_get_bert_region\|acpi_resume\|mainboard_suspend_resume\|acpi_find_wakeup_vector\|ACPI_S\|acpi_sleep_from_pm1\|acpi_get_preferred_pm_profile\|acpi_get_sleep_type\|acpi_get_gpe\|permanent_smi_handler\|acpi_s3_resume_allowed\|acpi_is_wakeup_s3\|acpi_align_current\|get_acpi_table_revision' -- src/) |grep "<"
Change-Id: Ic890dc7c0ed02891d3144210016cd96f01c344d5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <martinroth@google.com>
|
|
Break TPM related Kconfig into the following dimensions:
TPM transport support:
config CRB_TPM
config I2C_TPM
config SPI_TPM
config MEMORY_MAPPED_TPM (new)
TPM brand, not defining any of these is valid, and result in "generic" support:
config TPM_ATMEL (new)
config TPM_GOOGLE (new)
config TPM_GOOGLE_CR50 (new, implies TPM_GOOGLE)
config TPM_GOOGLE_TI50 (new to be used later, implies TPM_GOOGLE)
What protocol the TPM chip supports:
config MAINBOARD_HAS_TPM1
config MAINBOARD_HAS_TPM2
What the user chooses to compile (restricted by the above):
config NO_TPM
config TPM1
config TPM2
The following Kconfigs will be replaced as indicated:
config TPM_CR50 -> TPM_GOOGLE
config MAINBOARD_HAS_CRB_TPM -> CRB_TPM
config MAINBOARD_HAS_I2C_TPM_ATMEL -> I2C_TPM && TPM_ATMEL
config MAINBOARD_HAS_I2C_TPM_CR50 -> I2C_TPM && TPM_GOOGLE
config MAINBOARD_HAS_I2C_TPM_GENERIC -> I2C_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_LPC_TPM -> MEMORY_MAPPED_TPM
config MAINBOARD_HAS_SPI_TPM -> SPI_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_SPI_TPM_CR50 -> SPI_TPM && TPM_GOOGLE
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Change-Id: I4656b2b90363b8dfd008dc281ad591862fe2cc9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Before:
[DEBUG] dw_i2c: SoC 400/3000 ns Bus: 400/1000000 ns
[DEBUG] dw_i2c: period 334 rise 13 fall 2 tlow 174 thigh 80 spk 7
[DEBUG] dw_i2c: hcnt = 104 lcnt = 202 sda hold = 7
After:
[DEBUG] dw_i2c: SoC 400/3000 ns Bus: 400/1000000 ns
[DEBUG] dw_i2c: period 334 rise 13 fall 2 tlow 174 thigh 80 spk 7
[DEBUG] dw_i2c: hcnt = 104 lcnt = 202 sda hold = 7
BUG=None
TEST=Check that the formatting looks correct, as above.
Change-Id: I6703a5d6512cee7848edae27afcfd82eb89bcacb
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Ti50 FW under 0.15 is not support board cfg command which causes I2C
errors and entering recovery mode. And ODM stocks are 0.12 pre-flashed.
Add workaround for the old Ti50 chip.
BUG=b:224650720
TEST=no I2C errors in coreboot.
[ERROR] cr50_i2c_read: Address write failed
[INFO ] .I2C stop bit not received
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ieec7842ca66b4c690df04a400cebcf45138c745d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
This patch is adding support for Cirrus Logic CS35l41/CS35l53
smart amplifier. This part is now used in number of new chromebook's
HW designs by several vendors.
This driver uses the ACPI Device Property interface to generate
the required parameters into the _DSD table format expected by
the kernel. For detailed information about these properties, please
check Linux kernel documentation:
/Documentation/devicetree/bindings/sound/cirrus,cs35l41.yaml
Change-Id: I2cbb1cef89f8d56ee73fab06c68933a2ab8c3606
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch introduces CONFIG_I2C_TRANSFER_TIMEOUT_US,
which controls how long to wait for an I2C devices to
produce/accept all the data bytes in a single transfer.
(The device can delay transfer by stretching the clock of
the ack bit.)
The default value of this new setting is 500ms. Existing
code had timeouts anywhere from tens of milliseconds to a
full second beween various drivers. Drivers can still have
their own shorter timeouts for setup/communication with the
I2C host controller (as opposed to transactions with I2C
devices on the bus.)
In general, the timeout is not meant to be reached except in
situations where there is already serious problem with the
boot, and serves to make sure that some useful diagnostic
output is produced on the console.
Change-Id: I6423122f32aad1dbcee0bfe240cdaa8cb512791f
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch replaces remaining `cb_err_t` with `enum cb_err` after commit
hash 69cc557c (commonlib/bsd: Remove cb_err_t) removes majority of
`cb_err_t` instances.
TEST=Able to build the brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3392f9c2cfb4a889a999c8ea25066c89979f0900
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This allows mainboards using an I2C bus to communicate with the cr50
to reuse the functionality related to firmware version and BOARD_CFG.
BUG=b:202246591
TEST=boot on brya0, see cr50 FW version in logs
Change-Id: Ide1a7299936193da3cd3d15fdfd1a80994d70da0
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Turns out 200ms still isn't enough in the worst reset conditions.
There's been some reports of failures at 200ms with some older
cr50 versions. Let's not take any chances and bump this way up
since if this fails, it prevents boot.
BUG=b:213828947
BRANCH=None
TEST=Reboot and suspend_stress on Nipperkin
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I5be0a80c064546fd277f66135abc9d0572df11cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The `chip` argument passed around to many functions in this driver is
actualy unused, so remove it where it is unused.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib8d32fdf340c8ef49fefd11da433e3b6ee561f29
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Now that the console system itself will clearly differentiate loglevels,
it is no longer necessary to explicitly add "ERROR: " in front of every
BIOS_ERR message to help it stand out more (and allow automated tooling
to grep for it). Removing all these extra .rodata characters should save
us a nice little amount of binary size.
This patch was created by running
find src/ -type f -exec perl -0777 -pi -e 's/printk\(\s*BIOS_ERR,\s*"ERROR: /printk\(BIOS_ERR, "/gi' '{}' ';'
and doing some cursory review/cleanup on the result. Then doing the same
thing for BIOS_WARN with
's/printk\(\s*BIOS_WARNING,\s*"WARN(ING)?: /printk\(BIOS_WARNING, "/gi'
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I3d0573acb23d2df53db6813cb1a5fc31b5357db8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Lance Zhao
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
|
|
The speed control bits of the Designware I2C controller are bits 1 and 2
in the control register, so the values should be written as number
shifted by the number of the first bit. The resulting constant is
identical.
TEST=Timeless build for amd/chausie results in identical binary
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id0881dfcd7703ab6a70a9b1a355d5a93771aebc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Using enum cb_err as return type instead of int improves the readability
of the code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8d96e5f72a8b3552ab39c1d298bafcc224bf9e55
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61512
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Outside of the designware I2C driver the generic platform_i2c_transfer
function should be used instead, so don't make dw_i2c_transfer available
outside of this file.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib8b6a08b6aa2cd63adc2ef69b828661fa0ed154a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Using enum cb_err as return type instead of int improves the readability
of the code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic1812c4d8d2b4d9ad331a787bd302a4f0707c1fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Using enum cb_err as return type instead of int improves the readability
of the code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I55e6d93ca141b687871ceaa763bbbbe966c4b4a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
|
|
Using enum cb_err as return type instead of int improves the readability
of the code. This commit only changes the return value of the static
functions in this file keeping the external interface identical.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I80300e0b24591fc660c3134139b9257e002cdbbb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
size_t is defined in stddef.h and not stdint.h, so include types.h to
get both.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3782d3a949b72d1530ebd8078c46bc695f76dc4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This will provide the definitions for size_t, uint32_t and uintptr_t.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Icda8d458565bf981545d720d612cbdace04bedd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Add driver for setting up Semtech sx9360 SAR sensor.
The driver is based on sx9310.c. The core of the driver is the same, but
the bindings are slightly different.
Registers are documented in the kernel tree:
Documentation/devicetree/bindings/iio/proximity/semtech,sx9360.yaml
[https://patchwork.kernel.org/project/linux-iio/patch/20211213024057.3824985-4-gwendal@chromium.org/]
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Change-Id: I0a912f184e6f3501f894cca24c0d71a2c3087516
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Turns out 150ms isn't enough in the worst reset conditions. On guybrush
the TPM is reset in S0i3 and the CR50 is allowed to hibernate. The CR50
is woken up and initialized early during S0i3 resume. Occasionally the
CR50 isn't ready before the probe times out.
BUG=b:213828947
BRANCH=None
TEST=suspend_stress_test -c 1000
Change-Id: Ifda438080cf1ad2796c7061223a6a97b8e6e9987
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Keith Short <keithshort@chromium.org>
|
|
I2C bus and address of the TPM are typically fixed on hardware so
there is no need to be able to configure this in menuconfig.
Change-Id: I1b6afa68fe753fb76348e0461209d218b14df7cb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Found using:
diff <(git grep -l '#include <stdlib.h>' -- src/) <(git grep -l 'memalign(\|malloc(\|calloc(\|free(' -- src/)
Change-Id: Id3bd3d8a2d3609a13ecbc4eab14ba745e6365cab
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
CB:59479 introduced a blank default statement. This is treated as an
error or warning on some older toolchains. Add a break statement on
default case.
BUG=None
TEST=Build the Guybrush mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I3d034cfebc8b8ae7d7024d41b4b2207cdeb083e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Introduce firmware-power-managed DSD ACPI property for TPM devices.
This property can be checked by the kernel TPM driver to override how
the TPM power states are managed. This is a tri-state flag, true,
false, or unset. So an enum used to keep the flag is unset by default.
When firmware-power-managed is true, the kernel driver will not send a
shutdown during s2idle/s0i3 suspend.
BUG=b:200578885
BRANCH=None
TEST=TPM shutdown is triggered on s0ix suspend on guybrush with patched
kernel
Change-Id: Ia48ead856fc0c6e637a2e07a5ecc58423f599c5b
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
These issues were found and fixed by codespell, a useful tool for
finding spelling errors.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I5b8ecdfe75d99028fee820a2034466a8ad1c5e63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58080
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add two properties (maxim, vmon-slot-no/maxim, imon-slot-no) in maxim9839 driver.
This is I/V source destination definition that from below properties .
maxim,vmon-slot-no => PCM_IVADC_V_DEST
maxim,imon-slot-no => PCM_IVADC_I_DEST
BUG=b:197076844
TEST=build and check SSDT
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Idb24d19c7cfea559bf6d53f401d66cadb8b3acc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Maxim driver look for "maxim,dsm_param_name" to load dsm parameter file.
dsm param file name consist of {dsm_param_file_name} filled in devicetree,
{MAINBOARD_VENDOR} and {MAINBOARD_PART_NUMBER}.
=> {dsm_param_file_name}_{MAINBOARD_VENDOR}_{MAINBOARD_PART_NUMBER}.bin
BUG=b:197076844
TEST=build, and check ssdt
Change-Id: I006572d6a6ea55298374c688dfd9d877835da82d
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Move bcd2bin() / bin2bcd() functions to commonlib/bsd/include/
Also, the license is changed from GPL to BSD.
This is because it is needed from "utils" (see CL in the chain).
For reference bin2bcd() & bcd2bin() are very simple functions.
There are already BSD implementations, like these ones (just to
name a few):
https://chromium.googlesource.com/chromiumos/platform/mosys/+/refs/heads/main/include/lib/math.h#67
http://web.mit.edu/freebsd/head/sys/contrib/octeon-sdk/cvmx-cn3010-evb-hs5.c
BUG=b:172210863
TEST=make (everything compiled Ok).
Change-Id: If2eba82da35838799bcbcf38303de6bd53f7eb72
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56904
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The DA7219 does not support wake from D3cold, therefore update the
return value of _S0W from D3cold to D3hot.
BUG=b:187228954
TEST=compile
Change-Id: If03f83bb00ec90a2a6646d2c99d8bcc7e5533ac2
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Since the OS provides its own driver for the I2C controller it can
choose to use a bus speed other than the one used at coreboot runtime.
In this case it would be good to provide a way how the needed bus
timings are communicated to the OS, since these are very board-specific
and there is no way that the OS can know them other than read the
appropriate ACPI reported timings.
This patch adds some code to report additional bus speed timings if
there are some defined in the devicetree.
Change-Id: If921e0613864660dc1bb8d7c1b30fb9db8ac655d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
In commit b64db833d6 a basic ACPI support was added to the driver.
With this support an SSDT-entry is created for this RTC and it is now
visible to the OS via ACPI. In Linux the PNP-devices, which are
reported over ACPI, are scanned rather early and if the entry is found,
the device is claimed even if there is no driver available yet.
In this case, when the native RTC-driver without ACPI-support is loaded
and tries to register this device, the RTC is already blocked by the
PNP-drivers and cannot be used anymore. This leads to a non-usable RTC
on kernels where the needed ACPI-extension is not yet merged into the
RTC driver.
This patch provides a way to disable the ACPI-support for the RTC if
needed.
Change-Id: Ic65794d409d13a78d17275c86ec14ee6f04cd2a6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55003
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
HSBIAS_SENSE_EN configures HSBIAS output current sense through
the external 2.21-k resistor. HSBIAS_SENSE is hardware feature to reduce
the potential pop noise during the headset plug out slowly. But on some
platforms ESD voltage will affect it causing test to fail, especially
with CTIA headset type. For different hardware setups, a designer might
want to tweak default behavior.
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.corp-partner.google.com>
Change-Id: I87c6f01af1bdb5b1cb8e399191519598d7fbe9ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52981
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If device is supported as a wake source, _S0W should be set to D3hot.
This ensures that the device is put into D3hot by the OSPM.
Power resource(PRIC) for the device is listed in both _PR0 and _PR3. Thus, it ensures that the OSPM does not turn off power resource when device is put into D0 and D3hot. Hence, it is capable of waking the system from D3hot state. However, if it is put into D3cold, then the power resource is turned off by the OSPM.
The devices we are currently looking at for touchscreen/touchpad
do not really support auxiliary power and so do not support wake from D3cold.
BUG=b:186070097
TEST=build and check device wake state _S0W set to 3 in ssdt table.
Change-Id: I34e4b2350875530d3337be700276bcc4fb1f810a
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Inspired by discussion in CB:22822.
If I2C bus step response has not been measured, assume the layout to
have been designed with a minimal capacitance and SCL rise and fall
times of 0 ns. The calculations will add the required amount of
reference clocks for the host to drive SCL high or low, such that the
maximum bus frequency specification is met.
Change-Id: Icbafae22c83ffbc16c179fb5412fb4fd6b70813a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52723
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This driver uses the ACPI Device Property interface to generate
the required parameters into the _DSD table format expected by
the kernel
This was tested on the octopus/variants/fleex ainboard to ensure
that the SSDT contained the equivalent parameters that are provided
by the current DSDT object
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.corp-partner.google.com>
Change-Id: I7c3145b20a1ba743d91eb64b93cb001db3854c5d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This adds a driver for the TI TAS5825M smart amplifier [1].
The driver expects the mainboard using it to define tas5825m_setup(),
which uses the tas5825m_* functions to set configuration data. Each
mainboard may have very different configuration data, depending on
its audio hardware.
Tested on System76 addw1, bonw14, oryp5, and oryp6.
[1]: https://www.ti.com/product/TAS5825M
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Change-Id: I896e8f272f18e64bfc90f406e7d4163010800aaf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add definitions to describe GPIOs in generated ACPI objects.
The method allow either write a GpioInt() or Interrupt() descriptor.
Signed-off-by: Seven Lee <wtli@nuvoton.com>
Change-Id: I37fec7b0b9324dbfb61b7a8bea80f45026c54409
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51922
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current driver is using chip registers map to configure the SAR
sensor, which is opaque, especially when the datasheet is not published
widely.
Use more descriptive names, as defined in Linux kernel documentation at
https://www.kernel.org/doc/Documentation/devicetree/bindings/iio/proximity/semtech%2Csx9310.yaml
BUG=b:173341604
BRANCH=volteer
TEST=Dump all tables, check semtech property:
for i in $(find /sys/firmware/acpi/tables/ -type f) ; do
f=$(basename $i); cat $i > /tmp/$f.dat ; iasl -d /tmp/$f.dat
done
In SSDT.dsl, we have:
Package (0x06)
{
Package (0x02)
{
"semtech,cs0-ground",
Zero
},
Package (0x02)
{
"semtech,startup-sensor",
Zero
},
Package (0x02)
{
"semtech,proxraw-strength",
Zero
},
Package (0x02)
{
"semtech,avg-pos-strength",
0x0200
},
Package (0x02)
{
"semtech,combined-sensors",
Package (0x03)
{
Zero,
One,
0x02
}
},
Package (0x02)
{
"semtech,resolution",
"finest"
}
}
Change-Id: I8d1c81b56eaeef1dbb0f73c1d74c3a20e8b2fd7b
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In commit 2609eaaa8f (src/drivers/i2c/rx6110sa: Omit _HID temporarily)
the randomly assigned and therefore wrong ACPI ID for RTC RX6110SA was
removed. In the meantime Seiko-Epson did a great job and registered an
official vendor ID in the ACPI database [1]. Further on, Seiko-Epson
has now assigned the unique Product Identifier for the RX6110SA, which
is '6110'. The assignment of the Product Identifier is controlled by
the vendor and there is no official database where this ID is stored
in. It is up to the vendor to make sure that this ID stays unique.
This patch adds this new vendor and product ID to the driver. Together
with a pending Linux patch this RTC is now useable as ACPI device in
Linux.
[1] https://uefi.org/ACPI_ID_List?search=SECC
Change-Id: I45838162f014a760520692c6dcaae329ad98547d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51176
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Johannes Hahn <johannes-hahn@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
This change ensures that the IRQ is appropriately configured.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild. Build and boot to OS in Dedede.
Change-Id: I3245a9de6e88cd83528823251083e62288192f0d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: If2751f3672072b7fa421ae33dc6e1490fdf35247
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Change-Id: I28f976118a380ef05a98257e9d57aadc26b69cb5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Change-Id: I598d27995fad7582ff41f4e7deaeb2e75e8ebde9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Add IrqCfg1 register for proximity IRQ function and polarity setting.
BUG=b:175932166
BRANCH=dedede
TEST=Build passed.
Change-Id: I3cee84a5658fecf55d2d8b8621879588ffe0158d
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49220
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DRIVER_I2C_TPM_ACPI is used to enable the "driver" needed for coreboot
to present a TPM node in the devicetree. It would usually only do so,
if coreboot itself is communicating with the TPM via I2C (I2C_TPM).
However, technically, there is no dependency.
In order to not show the ACPI option in menuconfig if the board is not
using I2C, a dependency was declared in Kconfig. However, the same can
be achieved without making it an error to manually declare
DRIVER_I2C_TPM_ACPI without I2C_TPM.
For Volteer, we have just such a need, since it has two "sub-variants"
sharing the same overridetree.cb, one having SPI TPM and another having
I2C TPM. The former will have a disabled ACPI node representing the I2C
TPM, while its Kconfig is such that coreboot itself does not have I2C
TPM support.
In order to export even a disabled ACPI node representing the I2C
connected TPM, coreboot needs DRIVER_I2C_TPM_ACPI. Hence, that will
have to be enabled in a case where coreboot does not have I2C_TPM (for
one of the two sub-variants, namely volteer2).
BUG=b:173461736
TEST=Tested as part of next CL in chain
Change-Id: I9717f6b68afd90fbc294fbbd2a5b8d0c6ee9ae55
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48222
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Export all registers that driver is looking for. And put in alphabetic order.
The missing registers for kernel v5.4 sx93xx are:
reg_irq_msk
reg_irq_cfg0
reg_irq_cfg2
reg_afe_ph0/1/2/3
BUG=b:172397658
BRANCH=zork
TEST=Build passed
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic9d7a959b1769b6846bba302e3aeab9a3a1cedac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47866
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current location for the sensor initialization procedure was chosen
by mistake. Move this into a separate function in nct7802y.c .
Change-Id: I093ae75db5f0051bff65375b0720c86642b9148a
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Follow model of drivers/i2c/generic and use user-supplied device
name if specified in the chip config.
Change-Id: Ia783bac2797e239989c03a3421b9293a055db3d0
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47782
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DDN field isn't required, no point in writing an empty string to it.
Change-Id: Ifea6e48c324598f114178e86a79f519ee35f5258
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47781
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds a new driver for the SX9324 proximity detector device.
Follow SX9324 datasheet Rev3.
BUG=b:172397658
BRANCH=zork
TEST=Test sx9324 is working as expected.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ifd582482728a2f535ed85f6696b2f5a4529ba421
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47640
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current HID "RX6110SA" does not comply with the ACPI spec in terms
of the naming convention where the first three caracters should be a
vendor ID and the last 4 characters should be a device ID. For now
there is a vendor ID for Epson (SEC) but there is none for this
particular RTC. In order to avoid the reporting of a non ACPI-compliant
HID it will be dropped completely for now.
Once Epson has assigned a valid HID for this RTC, this valid HID will be
used here instead.
Change-Id: Ib77ffad084c25f60f79ec7d503f14731b1ebe9e2
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47706
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The CONFIG_TPM_I2C_BURST_LIMITATION was never added, so this has never
been turned on. The Kconfig linter generates three warnings about this
block:
Warning: Unknown config option CONFIG_TPM_I2C_BURST_LIMITATION
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I53fa8f5b4eac6a1e7efec23f70395058bad26299
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47367
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is a trivial patch to fix some comments that were generating
notes in the kconfig lint test.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I26a95f17e82910f50c62215be5c29780fe98e29a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47366
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When the host sends data in i2c bus, device might not send ACK. It means
that data is not processed on the device side, but for now we don't
check for that condition thus wait for the response which will not come.
Designware i2c detect such situation and set TX_ABORT bit. Checking for
the bit will enable other layers to immediately retry rather than
wait-timeout-retry cycle.
BUG=b:168838505
BRANCH=zork
TEST=test on zork devices, now we see "Tx abort detected" instead of I2C
timeout for tpm initializtion.
Change-Id: Ib0163fbce55ccc99f677dbb096f67a58d2ef2bda
Signed-off-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The defines for RX6110SA_SLAVE_ADR and RX6110SA_I2C_CONTROLLER are not
used anymore and can be deleted.
Change-Id: I3cddf7a9e2f757a22c729ae0f0ff767d55909b9c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: siemens-bot
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
This patch adds basic ACPI support for the RTC so that the OS is able to
use this RTC via the ACPI interface.
If the Linux kernel is able to find the RTC in ACPI scope, you should
see the following lines in dmesg, where [n] is an enumerated number:
rx6110 i2c-RX6110SA:00: rtc core: registered RX6110SA:00 as rtc[n]
rtc rtc[n]: Update timer was detected
Change-Id: I9b319e3088e6511592075b055f8fa3e2aedaa209
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
