| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: I6b40aaf5af5d114bbb0cd227dfd50b0ee19eebba
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28934
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The device tree now supports 'hidden' and the status can be found in
`struct device.hidden`. A new acpi_device_status() will return the
expected setting of STA from a `struct device`.
BUG=b:72200466
BRANCH=eve
TEST=Builds and boots properly on device eve
Change-Id: I6dc62aff63cc3cb950739398a4dcac21836c9766
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/28567
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Under some conditions, cr50_i2c_read() can return without actually reading
the TPM, which will leave access uninitialized. Set an initial value for
access, and if TPM fails to respond in time check if at least TPM was read.
This way avoids printing an uninitialized value.
BUG=b:112253891
TEST=Build and boot grunt.
Change-Id: I5ec7a99396db32971dc8485b77158d735ab1d788
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: Ib0839933f8b59f0c87cdda4e5374828bd6f1099f
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/23759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Change-Id: I9144937b72a98517cbd41c093cff7bad543b4140
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27916
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These two da7219_aad properties are optional:
- dlg,micbias-pulse-lvl : Mic bias higher voltage pulse level (mV).
[<2800>, <2900>]
- dlg,micbias-pulse-time : Mic bias higher voltage pulse duration (ms)
When the Mic Bias Higher Voltage feature is not required, firmware should
just not provide the dlg,micbias-pulse-lvl and dlg,micbias-pulse-time
properties.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
BUG=b:111700809
TEST=On grunt:
No "Invalid micbias pulse level" in dmesg
Change-Id: Ie99a8962e78c68b3f6927d0de34168f265d4efa9
Reviewed-on: https://review.coreboot.org/27613
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Akshu Agrawal <akshu.agrawal@amd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic1c9b1edd8d3206a68854107ddcbc5c51cb487c3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I85cd567a923cccd2504f351aae276b5f0d9db4de
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt Delco <delco@google.com>
Reviewed-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
i2c/alps driver implementation is an exact copy of the i2c/hid driver
with only the addition of ALPS0001_HID. This can be supported by the
i2c/hid driver using the hid field in devicetree which is what glkrvp
mainboard does. So, this change removes the i2c/alps driver which is
anyways unused.
Change-Id: I60761c384f3d800532b2b346272da7be28b77acd
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change fixes the issue reported by Coverity CID 1393576 to ensure
that config is checked for NULL before it is actually used.
Change-Id: I5f0cd2bf2437fc640f4cf8d8203a971daf1f8d17
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Enrico Granata <egranata@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This adds a new driver for the SX9310 proximity detector device.
The purpose of this is to enable the device's calibration information
to be stored in firmware, and then transferred over to the kernel
via ACPI.
This device has more than 10 individual configuration parameters,
so they would not fit in the generic driver's properties table.
Change-Id: Id8c434eec9fe2da731e142442503a12e88db2236
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/27173
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change checks to ensure that config is not NULL before it is
accessed for the first time.
Reported by: Coverity CID #1393312
Change-Id: Ic248c79783da9c2bfdf3b7f737e5963feff7558c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Name i2c device structure based on that in devicetree.cb
Now log looks like:
I2C: 01:0a (WCOM Touchscreen)
I2C: 03:13 (Realtek RT5663)
I2C: 03:39 (SSM4567 Right Speaker Amp)
I2C: 03:3a (SSM4567 Left Speaker Amp)
BUG=None
BRANCH=None
TEST=Build & boot Soraka
Change-Id: I5dbb66ab705cd8601b8b1dc94bc6ee9f181b7be2
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/26830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
* Remove 2nd software stack in pc80 drivers directory.
* Create TSPI interface for common usage.
* Refactor TSS / TIS code base.
* Add vendor tss (Cr50) directory.
* Change kconfig options for TPM to TPM1.
* Add user / board configuration with:
* MAINBOARD_HAS_*_TPM # * BUS driver
* MAINBOARD_HAS_TPM1 or MAINBOARD_HAS_TPM2
* Add kconfig TPM user selection (e.g. pluggable TPMs)
* Fix existing headers and function calls.
* Fix vboot for interface usage and antirollback mode.
Change-Id: I7ec277e82a3c20c62a0548a1a2b013e6ce8f5b3f
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/24903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Upstream Kernel side codec driver expect DT properties
to have 'maxim' prefix.
Update accordingly while filling SSDT entries.
BUG=b:79362472
TEST=dump DT properties in kerenl side and cross checked
TEST=Audio playback works with this change
Change-Id: Iaa4b14492dbb5a0087242f1485493f3192336f60
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Iedb78e24a286a51830c85724af0179995ed553be
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Non-dts based systems can pass mclk to da7219 driver by
this property.
BUG=b:74570989
TEST=Enabled clock in kernel driver using the property
Change-Id: I2e10769e5b3c6b3aa30f340fe0e88c29b87430cb
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/25919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Some touchscreens need to adhere to certain timings during the power
off sequence as well as during the power on sequence. Adding
reset_off_delay_ms, enable_off_delay_ms, and stop_off_delay_ms to
accommodate these devices.
BUG=b:78311818
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: Idb4a5dbe56eee4749d2f2b514e92c28fb2c6078f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/25882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Id13eef7f0fca0b929372490859aa4734ea7a9f23
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/25868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Iaed9c0882847511642d8eaab25e10d1ecf24bf90
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/25867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I147b3a2c79cd5e6b0e5fa3d23221a6afda8ba8f7
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/25866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Ic525c92e73097752a7c690186dc2034785cac678
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/25821
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of writing out '__attribute__((weak))' use a shorter form.
Change-Id: If418a1d55052780077febd2d8f2089021f414b91
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Remove extra tab before printk statement.
Change-Id: Id82239f74ac030f25000a08764637f6d1b52b87b
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/25295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The chip PCA9538 is a 8 bit I/O expander connected to the systems I2C
bus. Add a chip driver to support this chip.
Beside the pure chip driver two interface functions are provided to read
the state of the pins and write output values to the pins.
As the slave address of this chip is hardware configurable the function
pca9538_get_dev() is used to get the right slave address. This function
needs to be implemented in mainboard code if one needs to use the
interface functions to read and write I/O state.
Change-Id: Ic856123b4f4c8b721928ee3a2a4bb37833ea4b20
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/23748
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fixes: b8dc63bdfe ("ic2/designware: Move Intel i2c logic to shared driver")
Change-Id: Ic521a2d60b403b322ae583bb2c26da6019bf0ab0
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/23714
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allow specifying the DA7219 interrupt pin as either an Interrupt or
GpioInt.
BUG=b:72121803
TEST=(with whole patch series) Grunt Kernel discovers DA7219 on i2c0
Change-Id: I2d26731bf4c0ad590dad2c5d26c252371f415f9a
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
The designware i2c controller indicates that the slave address
shouldn't be programmed while the controller is enabled. Therefore,
switch the ordering of the slave target address and the enable.
Additionally, ensure the controller is disabled prior to the
start of the slave programming sequence.
Lastly, chunk up the i2c_msg segments at differing slave address
boundaries. That allows for simpler programming for the controller
by only doing one slave address transaction chunk at a time.
BUG=b:70232394,b:69250772
Change-Id: Iebc08e2db847cb182fad98e0ff3d799b9a64aca7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
To set address on AMD, IC_ENABLE == 0.
BUG=b:69416132
BRANCH=none
TEST=Test communication with i2c TPM on grunt and coral
Change-Id: I7faee8e11439deceab946cc82d30d274b529b90d
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/23293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Grunt (a amd-stoneyridge based platform) uses a GPIO to interface with
the tpm. This change allows devicetree entries to use a irq_gpio entry
to describe the interface with the TPM.
BUG=b:72655090
Change-Id: I08289891408d7176f68eb9c67f7a417a2448c2de
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23500
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Right now dw_i2c_get_soc_cfg() is expecting the SoC to implement
that callback for obtaining the bus config. However, we're currently
forcing another parameter of struct device so one can do the lookup.
This works for Intel-based systems since the struct device was needed
to program the BAR, etc. However, from an API standpoint, it just
complicates matters by needing to obtain the struct device. The SoC
already has knowlege of its own devices so it can get the config
itself by bus number. Therefore, remove that contraint from the API.
BUG=b:70232394
Change-Id: Id8558f5deedda0963a46a532a7bf984e168fb270
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23420
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In ramstage the device_operations are needed for the i2c designware
host controller. Move the intel/common/block/i2c implementation
into the generic driver so other platforms can take advantage of it.
BUG=b:72121803
Change-Id: Id249933fadcc016bfba00e7a6d65f56dfc220724
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Rename the following functions to ensure it's clear that the designware
i2c host controller driver is the one that these functions are
associated with:
i2c_get_soc_cfg() -> dw_i2c_get_soc_cfg()
i2c_get_soc_early_base() -> dw_i2c_get_soc_early_base()
i2c_soc_devfn_to_bus() -> dw_i2c_soc_devfn_to_bus()
i2c_soc_bus_to_devfn() -> dw_i2c_soc_bus_to_devfn()
BUG=b:72121803
Change-Id: Idb7633b45a0bb7cb7433ef5f6b154e28474a7b6d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23371
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
If one wants to implement both i2c_bus.h and i2c_simple.h APIs
the compilation unit needs to be guarded or coordinated carefully
with different compilation units. Instead, name the i2c_bus
functions with _dev such that it indicates that they operate on
struct device. One other change to allow i2c_bus.h to be built in
non-ramstage environments is to ensure DEVTREE_CONST is used for
the dev field in struct bus.
BUG=b:72121803
Change-Id: I267e27e62c95013e8ff8b0728dbe9e7b523de453
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a device driver to generate the device and required properties
into the SSDT for max98373.
TEST=verified SSDT contained relevant params
BUG=None
Change-Id: Id45f74e52855f4b19276e1d3d673d5448207ef4b
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: N, Harshapriya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/22673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
* Rename tlcl* to tss* as tpm software stack layer.
* Fix inconsistent naming.
Change-Id: I206dd6a32dbd303a6d4d987e424407ebf5c518fa
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
* Move code from src/lib and src/include into src/security/tpm
* Split TPM TSS 1.2 and 2.0
* Fix header includes
* Add a new directory structure with kconfig and makefile includes
Change-Id: Id15a9aa6bd367560318dfcfd450bf5626ea0ec2b
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
BUG=b:70232394
BRANCH=none
TEST=emerge-reef coreboot
emerge-glados
Change-Id: Idb453a4d2411163e6b4a8422310bf272eac5d379
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/22822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The Cr50 i2c driver provides separate entry points for probing and
initialization, but probing function does not really do much.
It also claims and releases locality on every coreboot stage, but
there is no need for this - locality should be definitely claimed
after reset and then it could be retained through the boot process.
On top of that the driver does not properly account for long time it
could take the Cr50 chip to come around to reset processing if TPM
reset request was posted during a lengthy TPM operation.
This patch addresses the issues as follows:
- tpm_vendor_probe() and tpm_vendor_cleanup() become noops, kept
around to conform to the expected driver API.
- tpm_vendor_init() invokes a function to process TPM reset only in
the first stage using TPM (typically verstage), the function
checks if locality is claimed and if so - waits for it to be
released, which indicates that TPM reset processing is over.
- before claiming locality check if it is already taken, and if so -
just proceed.
BRANCH=none
BUG=b:65867313, b:68729265
TEST=Verified that reef no longer hangs during EC reboot and
firmware_Cr50ClearTPMOwner (not yet merged) tests.
Change-Id: Iba8445caf1342e3a5fefcb2664b0759a1a8e84e3
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/22554
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In case the TPM is doing a long crypto operation the initial probe
could be very delayed. Rather than end up in recovery make the delay
long enough to accommodate the (current) long crypto times.
BUG=b:65867313, b:68729265
TEST=Verified that Soraka no longer hangs during EC reboot test.
Change-Id: I3bccff70e001dfc065c24be8ad34ef239a144db1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Some Siemens copyright entries incorrectly contain a dot at the end of
the line. This is fixed with this patch.
Change-Id: I8d98f9a7caad65f7d14c3c2a0de67cb636340116
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I4d6c6810b91294a7e401a4a1a446218c04c98e55
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
There's no reason to mutate the struct device when determining
the ACPI name for a device. Adjust the function pointer
signature and the respective implementations to use const
struct device.
Change-Id: If5e1f4de36a53646616581b01f47c4e86822c42e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change list adds imon and vmon slot numbers as params for
Maxim 98927 driver. These values are looked up in the kernel driver
to confiure IV feedback for audio playback on speakers.
BUG=b:36724448
TEST=After boot, the register dump for Max98927 codecs should have
imon and vmon slots numbers set in 0x1e register.
Change-Id: I21d72ba91af83782587f11018b2d1d1c8d4f676c
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/21195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There is at least one I2C device (being used by Soraka) that has 3
controls -- enable, reset and stop. If the stop gpio is not put into
the right state when turning off the device in suspend mode, then it
causes leakage. Thus, we need control in power resource to be able to
stop the device when entering suspend state.
BUG=b:64987428
TEST=Verified on soraka that touchscreen stop is correctly configured
on suspend.
Change-Id: Iae5ec7eb3972c5c7f80956d60d0d3c321bbefb0f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21249
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replaces the ics/954309 driver with a more generic version to
accommodate clockgens with a different amount of registers.
It also features a mask to only touch certain bits of the clockgen.
TODO: set appropriate mask for X60/T60 since the datasheets for their
clockgens can be found.
Change-Id: Ie43c4de7891a39f2f443e78213ecd688134e68d7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add support for providing additional free form device properties via
devicetree in order to make this driver suitable for kernel drivers
that need additional board-specific device properties.
This currently allows adding up to 10 additional properties to a device.
BUG=b:63413023
TEST=manual testing to ensure that newly added properties are in SSDT
Change-Id: I2b8ceb208f4aba01053746547def6d07c8f8f3a2
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/21270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ib31e77eec639c231520198c0b978d6c3c1eadaed
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Split `i2c.h` into three pieces to ease reuse of the generic defi-
nitions. No code is changed.
* `i2c.h` - keeps the generic definitions
* `i2c_simple.h` - holds the current, limited to one controller driver
per board, devicetree independent I2C interface
* `i2c_bus.h` - will become the devicetree compatible interface for
native I2C (e.g. non-SMBus) controllers
Change-Id: I382d45c70f9314588663e1284f264f877469c74d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Our current struct for I2C segments `i2c_seg` was close to being compa-
tible to the Linux version `i2c_msg`, close to being compatible to SMBus
and close to being readable (e.g. what was `chip` supposed to mean?) but
turned out to be hard to fix.
Instead of extending it in a backwards compatible way (and not touching
current controller drivers), replace it with a Linux source compatible
`struct i2c_msg` and patch all the drivers and users with Coccinelle.
The new `struct i2c_msg` should ease porting drivers from Linux and help
to write SMBus compatible controller drivers.
Beside integer type changes, the field `read` is replaced with a generic
field `flags` and `chip` is renamed to `slave`.
Patched with Coccinelle using the clumsy spatch below and some manual
changes:
* Nested struct initializers and one field access skipped by Coccinelle.
* Removed assumption in the code that I2C_M_RD is 1.
* In `i2c.h`, changed all occurences of `chip` to `slave`.
@@ @@
-struct i2c_seg
+struct i2c_msg
@@ identifier msg; expression e; @@
(
struct i2c_msg msg = {
- .read = 0,
+ .flags = 0,
};
|
struct i2c_msg msg = {
- .read = 1,
+ .flags = I2C_M_RD,
};
|
struct i2c_msg msg = {
- .chip = e,
+ .slave = e,
};
)
@@ struct i2c_msg msg; statement S1, S2; @@
(
-if (msg.read)
+if (msg.flags & I2C_M_RD)
S1 else S2
|
-if (msg.read)
+if (msg.flags & I2C_M_RD)
S1
)
@@ struct i2c_msg *msg; statement S1, S2; @@
(
-if (msg->read)
+if (msg->flags & I2C_M_RD)
S1 else S2
|
-if (msg->read)
+if (msg->flags & I2C_M_RD)
S1
)
@@ struct i2c_msg msg; expression e; @@
(
-msg.read = 0;
+msg.flags = 0;
|
-msg.read = 1;
+msg.flags = I2C_M_RD;
|
-msg.read = e;
+msg.flags = e ? I2C_M_RD : 0;
|
-!!(msg.read)
+(msg.flags & I2C_M_RD)
|
-(msg.read)
+(msg.flags & I2C_M_RD)
)
@@ struct i2c_msg *msg; expression e; @@
(
-msg->read = 0;
+msg->flags = 0;
|
-msg->read = 1;
+msg->flags = I2C_M_RD;
|
-msg->read = e;
+msg->flags = e ? I2C_M_RD : 0;
|
-!!(msg->read)
+(msg->flags & I2C_M_RD)
|
-(msg->read)
+(msg->flags & I2C_M_RD)
)
@@ struct i2c_msg msg; @@
-msg.chip
+msg.slave
@@ struct i2c_msg *msg; expression e; @@
-msg[e].chip
+msg[e].slave
@ slave disable ptr_to_array @ struct i2c_msg *msg; @@
-msg->chip
+msg->slave
Change-Id: Ifd7cabf0a18ffd7a1def25d1d7059b713d0b7ea9
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This commit adds a new driver for the RT5663 codec to use instead
of the generic i2c driver. Since the kernel needs additional
driver-specific device properties we need a BIOS driver that can
provide those properties.
The kernel driver devicetree properties for this codec are at:
linux/Documentation/devicetree/bindings/sound/rt5663.txt
This was tested by booting and verifying the generated SSDT
contains the expected device properties in _DSD.
Scope (\_SB.PCI0.I2C4)
{
Device (RT53)
{
Name (_HID, "10EC5663")
Name (_UID, Zero)
Name (_DDN, "Realtek RT5663 Codec")
Method (_STA, 0, NotSerialized)
{
Return (0x0F)
}
Name (_CRS, ResourceTemplate ()
{
I2cSerialBus (0x0013, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C4",
0x00, ResourceConsumer)
GpioInt (Edge, ActiveBoth, Exclusive, PullDefault, 0x0000,
"\\_SB.PCI0.GPIO", 0x00, ResourceConsumer)
{
0x0051
}
})
Name (_DSD, Package (0x02)
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301")
Package (0x05)
{
Package (0x02)
{
"irq-gpios",
Package (0x04)
{
\_SB.PCI0.I2C4.RT53,
Zero,
Zero,
Zero
}
},
Package (0x02)
{
"realtek,dc_offset_l_manual",
0x00FFD160
},
Package (0x02)
{
"realtek,dc_offset_r_manual",
0x00FFD1C0
},
Package (0x02)
{
"realtek,dc_offset_l_manual_mic",
0x00FF8A10
},
Package (0x02)
{
"realtek,dc_offset_r_manual_mic",
0x00FF8AB0
}
}
})
}
}
Change-Id: I3425fcbe13c9a5987fc91086d283a86db55c0819
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Ensure that the VLF bit will be cleared after a power loss event even if
the stopwatch has expired before the code to clear the bit is reached.
Change-Id: Ib2cfdabf4cd4df834395d6a102c6ae70568e71db
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
This excludes files which are mostly spaces, which I felt should be
handled separately.
Change-Id: I33043a3090e2fc6e9d2fd81e8a5e46fb6cb0aa35
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Also unify __attribute__ ((..)) to __attribute__((..)) and
handle ((__packed__)) like ((packed))
Change-Id: Ie60a51c3fa92b5009724a5b7c2932e361bf3490c
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/15921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
According to the datasheet the RTC needs a power rising slope of no more
than 100µs/V to ensure a correct power-on reset. If the mainboard that
hosts the RTC cannot guarantee this, a software reset sequence is needed
in the case where the battery was drained completely.
As the rising slope of the power supply depends on so many parameters
and is highly mainboard specific, refactor the initialization code to
perform a software reset every time a power loss event is recognized by
the RTC.
Change-Id: If64d672e51667523058041bd00e1e50ac047143d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The RTC RX6110SA has several configuration options which might be
interesting to set. To make this setup independent of the driver itself
but let it still be configurable on mainboard level, add more
configuration options to the chip driver.
Change-Id: I7f8b2aa7cd001a887f271be36f655e10e60e778b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The driver for the RTC RX6110SA is designed to be used with I2C bus.
This patch adds the possibility to use SMBus operations to access the
RTC. For this purpose the Kconfig switch RX6110SA_USE_SMBUS is added. It
is not enabled per default so that I2C will be used. One can set this
switch on board level to use SMBus instead.
Change-Id: I4827ae2c544e8002399d94a1159acacd8176c5e9
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19978
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This driver enables the usage of the external RTC chip RX6110 SA
(http://www5.epsondevice.com/en/products/i2c/rx6110sab.html) which is
connected to the I2C bus. The I2C address of this device is fixed. One
can change parameters in the device tree so that the used setup can be
adapted to match the configuration of the device on the mainboard.
Change-Id: I1290a10c2d5ad76a317c99c8b92a013309a605d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The vendor.irq field was originally intended for use as the TPM 1.2
"command complete" interrupt. However, all actual coreboot tpm drivers
and hardware use the vendor.status method of checking command completion
instead, and this irq field is not used.
Let's just remove this unused functionality to simplify the code.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
Change-Id: I994c5bfbd18124af9cb81d9684117af766ab0124
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19396
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The Cr50 TPM uses an IRQ to provide a "status" signal used for hand-shaking
the reception of commands. Real IRQs are not supported in firmware,
however firmware can still poll interrupt status registers for the same
effect.
Commit 94cc485338a3 ("drivers/i2c/tpm/cr50: Support interrupts for status")
added support for the Cr50 driver on X86 platforms to use a KConfig file
to supply an IRQ which it would poll using acpi_get_gpe. If the IRQ is
not supplied, the Cr50 driver inserts a 20 ms wait.
Unfortunately this doesn't work so well when using the i2c connected Cr50
on ARM platforms. Luckily, a more generic implementation to allow a
mainboard to supply a Cr50 IRQ status polling function was solved for SPI
connected Cr50s by commit 19e3d335bddb ("drivers/spi/tpm: using tpm irq to
sync tpm transaction").
Let's refactor the i2c c50 driver to use this same approach, and change
eve and reef boards to make use of DRIVER_TPM_TIS_ACPI_INTERRUPT for
specifying the TPM flow control interrupt.
This essentially reverts these two commits:
48f708d199 drivers/i2c/tpm/cr50: Initialize IRQ status handler before probe
94cc485338 drivers/i2c/tpm/cr50: Support interrupts for status
And ports this commit to i2c/tpm/cr50:
19e3d335bd drivers/spi/tpm: using tpm irq to sync tpm transaction
As a side effect the tpm_vendor_specific IRQ field goes back to its
original usage as the "TPM 1.2 command complete" interrupt, instead of
being repurposed to hold the flow control IRQ.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
Change-Id: I004329eae1d8aabda51c46b8504bf210484782b4
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19363
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Depend on I2C_TPM to prevent showing the menu entry on systems
that do not have an I2C TPM installed.
Change-Id: I7cd647c9c7e9721eab96ab64b844a882f156ee68
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19374
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
1. Move common TIS macros to include/tpm.h.
2. Use common TIS macros while referring to status and access registers.
3. Add a new function claim_locality to properly check for required
access bits and claim locality 0.
BUG=b:36873582
Change-Id: I11bf3e8b6e1f50b7868c9fe4394a858488367287
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19213
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The tis.c module is needlessly copying data to/from a 1260 byte
buffer on the stack. Each device's transport implementation (cr50.c
or tpm.c) maintains its own buffer, if needed, for framing purposes.
Therefore, remove the duplicated buffer.
BUG=b:36598499
Change-Id: I478fb57cb65509b5d74bdd871f1a231f8080bc2f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19061
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
The 'ordinal' variable is not used. Remove it.
BUG=b:36598499
Change-Id: I015a6633c0951980658b3c879e48bc84d604d62e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19060
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
There are unused structures/types in the tpm.h header file.
Remove them.
BUG=b:36598499
Change-Id: Iddc147640dcec70e80791846eb46298de1070672
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19059
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
In builds without CONFIG_VBOOT_SEPARATE_VERSTAGE, verstage files are
linked directly into the bootblock or the romstage. However, they're
still compiled with a separate "libverstage" source file class, linked
into an intermediate library and then linked into the final destination
stage.
There is no obvious benefit to doing it this way and it's unclear why it
was chosen in the first place... there are, however, obvious
disadvantages: it can result in code that is used by both libverstage
and the host stage to occur twice in the output binary. It also means
that libverstage files have their separate compiler flags that are not
necessarily aligned with the host stage, which can lead to weird effects
like <rules.h> macros not being set the way you would expect. In fact,
VBOOT_STARTS_IN_ROMSTAGE configurations are currently broken on x86
because their libverstage code that gets compiled into the romstage sets
ENV_VERSTAGE, but CAR migration code expects all ENV_VERSTAGE code to
run pre-migration.
This patch resolves these problems by removing the separate library.
There is no more difference between the 'verstage' and 'libverstage'
classes, and the source files added to them are just treated the same
way a bootblock or romstage source files in configurations where the
verstage is linked into either of these respective stages (allowing for
the normal object code deduplication and causing those files to be
compiled with the same flags as the host stage's files).
Tested this whole series by booting a Kevin, an Elm (both with and
without SEPARATE_VERSTAGE) and a Falco in normal and recovery mode.
Change-Id: I6bb84a9bf1cd54f2e02ca1f665740a9c88d88df4
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18302
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add support for using GPIO IRQ instead of PIRQ with an I2C device.
This allows a device to use an edge triggered interrupt that will
trigger on both high and low transitions.
The _DSD method for describing these GPIOs has a field for 'active
low' which is supposed to be 1 if the pin is active low, otherwise
is zero. The value in here doesn't mean too much for GpioInt() as
those will end up using the value from GpioInt() when it actually
requests the interrupt.
BUG=b:35581264
BRANCH=none
TEST=test on Eve board that codec IRQ can be delcared as GPIO IRQ
Change-Id: I02c64c7fc28dc2d608ad40db889c7242892f16db
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18835
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The I2C interface for the Atmel AT97SC3204 TPM varies greatly from the
existing I2C TPM support. The Atmel part just passes the commands and
responses from the TIS layer across the I2C interface.
TEST=Build and run on Galileo Gen2 with Crypto Shield and vboot enabled
Change-Id: Ib2ef0ffdfc12b2fc11fe4c55b6414924d4b676dd
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18800
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add debugging support for the TIS transactions for the I2C TPM chips.
TEST=Build and run on reef
Change-Id: Ibc7e26fca781316d625f4da080f34749f18e4f9b
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18799
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Fix the following warnings detected by checkpatch.pl:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: braces {} are not necessary for single statement blocks
WARNING: Unnecessary parentheses - maybe == should be = ?
WARNING: line over 80 characters
WARNING: missing space after return type
TEST=Build and run on Galileo Gen2
Change-Id: I56f915f6c1975cce123fd38043bad2638717d88c
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18832
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Wacom I2C driver does the same thing as I2C HID driver, other than
defining macros for Wacom HID. Instead of maintaining two separate
drivers providing the same functionality, update all wacom devices to
use generic I2C HID driver.
BUG=None
BRANCH=None
TEST=Verified that ACPI nodes for wacom devices are unchanged.
Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18401
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Move the function that adds a power resource block from
i2c/generic to the acpi device code at src/arch/x86/acpi_device.c
so it can be used by more drivers.
BUG=chrome-os-partner:61233
TEST=verify SSDT table generation is unchanged
Change-Id: I0ffb61a4f46028cbe912e85c0124d9f5200b9c76
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18391
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Maxim 98927 kernel driver requires entries in the ACPI SSDT table,
add a SSDT generator as part of this driver.
BUG=chrome-os-partner:62051
BRANCH=None
TEST=After boot, dump and verify that the generated SSDT ACPI table has the
required entries.
Change-Id: Ic2d4d8449288bc00d085852220b2e1e7a208e9ef
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: M Naveen <naveen.m@intel.com>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: https://review.coreboot.org/18211
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Linux kernel expects that power management with ACPI should always be
handled using PowerResource. However, some kernel drivers (e.g. ELAN
touchscreen) check to see if reset gpio is passed in by the BIOS to
decide whether the device loses power in suspend. Thus, until the kernel
has a better way for drivers to query if device lost power in suspend,
we need to allow passing in of GPIOs via _CRS as well as exporting
PowerResource to control power to the device.
Update mainboards to export reset GPIO as well as PowerResource for
ELAN touchscreen device.
BUG=chrome-os-partner:62311,chrome-os-partner:60194
BRANCH=reef
TEST=Verified that touchscreen works on power-on as well as after
suspend-resume.
Change-Id: I3409689cf56bfddd321402ad5dda3fc8762e6bc6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18238
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
We've found that the SLB9645 TPM sometimes seems to randomly start
returning 0xFF bytes for all requests. The exact cause is yet unknown,
but we should try to write our TIS code such that it avoids bad
interactions with this kind of response (e.g. any wait_for_status()
immediately succeeds because all "status bits" are set in the response).
At least for status and burstCount readings we can say for sure that the
value is nonsensical and we're already reading those in a loop until we
get valid results anyway, so let's add code to explicitly discount 0xFF
bytes.
BRANCH=oak
BUG=chrome-os-partner:55764
TEST=None
Change-Id: I934d42c36d6847a22a185795cea49d282fa113d9
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/420470
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://review.coreboot.org/18006
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add power management type config option that allows mainboards to
either:
1. Define a power resource that uses the reset and enable gpios to
power on and off the device using _ON and _OFF methods, or
2. Export reset and enable GPIOs in _CRS and _DSD so that the OS can
directly toggle the GPIOs as required.
GPIO type needs to be updated in drivers_i2c_generic_config to use
acpi_gpio type so that it can be used for both the above cases.
BUG=chrome-os-partner:60194
BRANCH=None
TEST=Verified that elan touchscreen works fine on reef using exported
GPIOs.
Change-Id: I4d76f193f615cfc4520869dedc55505c109042f6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17797
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add a generic I2C-HID driver for these types of devices that
do not need extra functionality. This allows a new device to
be added without having to write a new driver.
The i2c-hid PNP0C50 is automatically added as the _CID for the
device in the ACPI Device.
BUG=chrome-os-partner:58666
TEST=used on eve to describe a new i2c-hid touch controller
Change-Id: I94e9531a72f9bf1d6b3ade362b88883b21b83d0a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17856
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Remove any assumptions required for the drivers using i2c_generic to
have drivers_i2c_generic_config structure at the start of the driver
config. Instead pass in a pointer to drivers_i2c_generic_config from
the calling driver.
Change-Id: I51dc4cad1c1f246b51891abf7115a7120e87b098
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17857
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
In the case where the RTC is initialized after the battery is
completely drained the bits for power_mode and cof_selection are set up
with wrongly applied masks.
In the case where the RTC is re-initialized again with no power-loss
after the last initialization the bits for cap_sel, power_mode and
cof_selection are not shifted to the right position.
Both errors lead to a wrong initialization of the RTC and in turn to a
way larger current consumption (instead of 120 nA the RTC current rises
to over 2 µA).
This patch fixes both errors and the current consumption is in the right
range again.
TEST=booted mc_bdx1 and verified current consumption of RTC
Change-Id: I8594f6ac121a175844393952db2169dbc5cbd2b2
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/17829
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add support for I2C ALPS Touchpad Device Driver.
BUG=none
BRANCH=none
TEST=Build and booted successfully on KBL RVP and Touchpad is working
Change-Id: I78b77bd7c4694ccf61260724f593bd59545c70e6
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/17390
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Wacom I2C driver can be used by devices other than
touchscreen. e.g. digitizer. So there is no need to name the driver
with touchscreen specific attributes. Only a separate descriptor name
is required that needs to be set by mainboard correctly.
BUG=chrome-os-partner:56246
BRANCH=None
TEST=Compiles successfully.
Change-Id: I0d32a4adae477373b3f4c5f3abbe188860701194
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17341
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
WACOM request to add a new identifier `WCOMNTN2`,
and use that for the board Pyro with all LCD combinations.
BRANCH=master
BUG=chrome-os-partner:58093
TEST=emerge-pyro vboot_reference coreboot chromeos-bootimage
Signed-off-by: Janice Li <janice.li@quantatw.com>
Change-Id: I95cf357efba958d7e864d2736d324e0aad70e307
Reviewed-on: https://review.coreboot.org/17257
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Increase the IRQ timeout to prevent issues if there is a delay
in the TPM responding to a command. Split the no-IRQ case out
so it doesn't suffer unnecessarily.
BUG=chrome-os-partner:59191
TEST=suspend/resume testing on eve board
Change-Id: I1ea7859bc7a056a450b2b0ee32153ae43ee8699f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17204
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
BUG=chrome-os-partner:57846
Change-Id: Id6bd91b3fd6420994ad5811d362618b1a38a8afa
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17092
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
1. Export i2c_generic_fill_ssdt to allow other device-specific i2c
drivers to share and re-use the same code for generating AML code for
SSDT. In order to achieve this, following changes are required:
a. Add macro I2C_GENERIC_CONFIG that defines a structure with all
generic i2c device-tree properties. This macro should be placed by the
using driver at the start of its config structure.
b. Accept a callback function to add any device specific information to
SSDT. If generic driver is used directly by a device, callback would be
NULL. Other devices using a separate i2c driver can provide a callback
to add any properties to SSDT.
2. Allow device to provide _CID.
BUG=chrome-os-partner:57846
Change-Id: I3a0054e22b81f9d6d407bef417eae5e9edc04ee4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17089
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add support to allow a device to define PowerResource in its SSDT AML
code. PowerResouce ACPI generation expects SoC to define the
callbacks for generating AML code for GPIO manipulation.
Device requiring PowerResource needs to define following parameters:
1. Reset GPIO - Optional, GPIO to put device into reset or take it out
of reset.
2. Reset delay - Delay after reset GPIO is de-asserted (default 0).
3. Enable GPIO - Optional, GPIO to enabled device.
4. Enable delay - Delay after enable GPIO is asserted (default 0).
BUG=chrome-os-partner:55988
Change-Id: Ieb2dd95fc1f555f5de66f3dda425172ac5b75dad
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17081
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Return config->name if it is not NULL.
BUG=chrome-os-partner:55988
Change-Id: I9ae229949b73de6f991383daae8d962d6cf457a7
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17077
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: If79eb706b6d44f7c34dfe31a1545f5850870b334
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16866
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
UX Doc = go/gale-hw-ui
This color wasn't changed earlier as the change wasn't done in
the OS also. However, since we cannot change this later in FW
(but OS can change anytime), I am making this change after discussing
with the UX team.
BUG=b:31501528, b:31633562
TEST=Change the device state to 'recovery mode' to observe the new
color.
BRANCH=none
Change-Id: Ia91f14eb77492095cb41a9de0bb9790e72aa4851
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 36a3d8c6eabbc0b23d0a15d5bddc5ed3bdeebe70
Original-Change-Id: I88768b94cf91804a6005e44b1a168e059698ec4b
Original-Signed-off-by: Suresh Rajashekara <sureshraj@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/388206
Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org>
Original-Tested-by: Suresh Rajashekara <sureshraj@chromium.org>
Original-Reviewed-by: Christopher Book <cbook@chromium.org>
Original-Reviewed-by: Kan Yan <kyan@google.com>
Reviewed-on: https://review.coreboot.org/16767
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Colors and patterns as defined by the UX team
BUG=b:31501528
TEST=Move the device to different states in FW using rec and dev
button and verify the colors
BRANCH=None
Change-Id: I66d41a54590cd3ce4e5202c7cfa890f462fe195e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 703559d5dddaeeb7d435d6cadbb2009a1b7a76c8
Original-Change-Id: I95ab1fa59b483396ff1498a28f1ee98ac08d02d7
Original-Signed-off-by: Suresh Rajashekara <sureshraj@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/387258
Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org>
Original-Tested-by: Suresh Rajashekara <sureshraj@chromium.org>
Original-Reviewed-by: Christopher Book <cbook@chromium.org>
Original-Reviewed-by: Kan Yan <kyan@google.com>
Reviewed-on: https://review.coreboot.org/16718
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Gale EVT3 has only one LED controller (earlier we had 2).
Remove the support for the second controller and also the
corresponding microcode. The color values used are the same
as onHub (Arkham to be specific).
BUG=b:30890905
TEST=Move the device to different states manually by appropriate
actions (like dev mode, rec mode etc) and observe the different
colors.
BRANCH=None
Change-Id: I853035610ea7ea7c8d29c30d2de13c9e2e786b2b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 593905d2d69daa7482318aa5f5c5cd7cf984043e
Original-Change-Id: If8f22abd605faac6f6215ef600041740ce15ea0c
Original-Signed-off-by: Suresh Rajashekara <sureshraj@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/370821
Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org>
Original-Tested-by: Suresh Rajashekara <sureshraj@chromium.org>
Original-Reviewed-by: Kan Yan <kyan@google.com>
Reviewed-on: https://review.coreboot.org/16697
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Move the setup of the IRQ status handler so it will be set up properly
before the early probe happens.
BUG=chrome-os-partner:53336
Change-Id: I4380af1233d2a252899459635a3cb69ca196088d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16861
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
|
|
Kconfig hex values don't need to be in quotes, and should start with
'0x'. If the default value isn't set this way, Kconfig will add the
0x to the start, and the entry can be added unnecessarily to the
defconfig since it's "different" than what was set by the default.
A check for this has been added to the Kconfig lint tool.
Change-Id: I86f37340682771700011b6285e4b4af41b7e9968
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16834
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add a config option to the generic I2C device driver to indicate to
the OS that this device should be probed before being added.
This can be used to provide ACPI device instantiations to devices that
may not actually exist on the board. For example, if multiple trackpad
vendors are supported on the same board they can both be described in
ACPI and the OS will probe the address and load the driver only if the
device responds to the probe at that address.
BUG=chrome-os-partner:57686
Change-Id: I22cffb4b15f25d97dfd37dc58bca315f57bafc59
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16742
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Support reading the ACPI GPE status (on x86) to determine when
the cr50 is ready to return response data or is done processing
written data. If the interrupt is not defined by Kconfig then
it will continue to use the safe delay.
This was tested with reef hardware and a modified cr50 image
that generates interrupts at the intended points.
BUG=chrome-os-partner:53336
Change-Id: Ic8f805159650c45382cacac8840450a1f8b4d7a1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16672
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Unify the function names to be consistent throughout the driver
and improve the handling while waiting for data available and
data expected flags from the TPM.
BUG=chrome-os-partner:53336
Change-Id: Ie2dfb7ede1bcda0e77070df945c47c1428115907
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16668
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Clean up the mask and timeout handling in the locality functions
that were copied from the original driver.
BUG=chrome-os-partner:53336
Change-Id: Ifdcb3be0036b2c02bfbd1bcd326e9519d3726ee0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16667
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Rename the low-level functions from iic_tpm_read/write to
cr50_i2c_read/write to better match the driver name, and pass in the
tpm_chip structure to the low-level read/write functions as it will
be needed in future changes.
BUG=chrome-os-partner:53336
Change-Id: I826a7f024f8d137453af86ba920e0a3a734f7349
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16666
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use two different timeouts in the driver. The 2ms timeout is needed
to be safe for cr50 to cover the extended timeout that is seen with
some commands. The other at 2 seconds which is a TPM spec timeout.
BUG=chrome-os-partner:53336
Change-Id: Ia396fc48b8fe6e56e7071db9d74561de02b5b50e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16665
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Reduce the static buffer size from the generic default 1260
down to 64 to match the max FIFO size for the cr50 hardware
and reduce the footprint of the driver.
BUG=chrome-os-partner:53336
Change-Id: I6f9f71d501b60299edad4b16cc553a85391a1866
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16664
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
