| Age | Commit message (Collapse) | Author |
|---|
|
Split `i2c.h` into three pieces to ease reuse of the generic defi-
nitions. No code is changed.
* `i2c.h` - keeps the generic definitions
* `i2c_simple.h` - holds the current, limited to one controller driver
per board, devicetree independent I2C interface
* `i2c_bus.h` - will become the devicetree compatible interface for
native I2C (e.g. non-SMBus) controllers
Change-Id: I382d45c70f9314588663e1284f264f877469c74d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Also unify __attribute__ ((..)) to __attribute__((..)) and
handle ((__packed__)) like ((packed))
Change-Id: Ie60a51c3fa92b5009724a5b7c2932e361bf3490c
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/15921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The Cr50 TPM uses an IRQ to provide a "status" signal used for hand-shaking
the reception of commands. Real IRQs are not supported in firmware,
however firmware can still poll interrupt status registers for the same
effect.
Commit 94cc485338a3 ("drivers/i2c/tpm/cr50: Support interrupts for status")
added support for the Cr50 driver on X86 platforms to use a KConfig file
to supply an IRQ which it would poll using acpi_get_gpe. If the IRQ is
not supplied, the Cr50 driver inserts a 20 ms wait.
Unfortunately this doesn't work so well when using the i2c connected Cr50
on ARM platforms. Luckily, a more generic implementation to allow a
mainboard to supply a Cr50 IRQ status polling function was solved for SPI
connected Cr50s by commit 19e3d335bddb ("drivers/spi/tpm: using tpm irq to
sync tpm transaction").
Let's refactor the i2c c50 driver to use this same approach, and change
eve and reef boards to make use of DRIVER_TPM_TIS_ACPI_INTERRUPT for
specifying the TPM flow control interrupt.
This essentially reverts these two commits:
48f708d199 drivers/i2c/tpm/cr50: Initialize IRQ status handler before probe
94cc485338 drivers/i2c/tpm/cr50: Support interrupts for status
And ports this commit to i2c/tpm/cr50:
19e3d335bd drivers/spi/tpm: using tpm irq to sync tpm transaction
As a side effect the tpm_vendor_specific IRQ field goes back to its
original usage as the "TPM 1.2 command complete" interrupt, instead of
being repurposed to hold the flow control IRQ.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
Change-Id: I004329eae1d8aabda51c46b8504bf210484782b4
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19363
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
1. Move common TIS macros to include/tpm.h.
2. Use common TIS macros while referring to status and access registers.
3. Add a new function claim_locality to properly check for required
access bits and claim locality 0.
BUG=b:36873582
Change-Id: I11bf3e8b6e1f50b7868c9fe4394a858488367287
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19213
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Fix the following warnings detected by checkpatch.pl:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: braces {} are not necessary for single statement blocks
WARNING: Unnecessary parentheses - maybe == should be = ?
WARNING: line over 80 characters
WARNING: missing space after return type
TEST=Build and run on Galileo Gen2
Change-Id: I56f915f6c1975cce123fd38043bad2638717d88c
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18832
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Increase the IRQ timeout to prevent issues if there is a delay
in the TPM responding to a command. Split the no-IRQ case out
so it doesn't suffer unnecessarily.
BUG=chrome-os-partner:59191
TEST=suspend/resume testing on eve board
Change-Id: I1ea7859bc7a056a450b2b0ee32153ae43ee8699f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17204
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Move the setup of the IRQ status handler so it will be set up properly
before the early probe happens.
BUG=chrome-os-partner:53336
Change-Id: I4380af1233d2a252899459635a3cb69ca196088d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16861
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
|
|
Support reading the ACPI GPE status (on x86) to determine when
the cr50 is ready to return response data or is done processing
written data. If the interrupt is not defined by Kconfig then
it will continue to use the safe delay.
This was tested with reef hardware and a modified cr50 image
that generates interrupts at the intended points.
BUG=chrome-os-partner:53336
Change-Id: Ic8f805159650c45382cacac8840450a1f8b4d7a1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16672
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Unify the function names to be consistent throughout the driver
and improve the handling while waiting for data available and
data expected flags from the TPM.
BUG=chrome-os-partner:53336
Change-Id: Ie2dfb7ede1bcda0e77070df945c47c1428115907
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16668
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Clean up the mask and timeout handling in the locality functions
that were copied from the original driver.
BUG=chrome-os-partner:53336
Change-Id: Ifdcb3be0036b2c02bfbd1bcd326e9519d3726ee0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16667
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Rename the low-level functions from iic_tpm_read/write to
cr50_i2c_read/write to better match the driver name, and pass in the
tpm_chip structure to the low-level read/write functions as it will
be needed in future changes.
BUG=chrome-os-partner:53336
Change-Id: I826a7f024f8d137453af86ba920e0a3a734f7349
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16666
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use two different timeouts in the driver. The 2ms timeout is needed
to be safe for cr50 to cover the extended timeout that is seen with
some commands. The other at 2 seconds which is a TPM spec timeout.
BUG=chrome-os-partner:53336
Change-Id: Ia396fc48b8fe6e56e7071db9d74561de02b5b50e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16665
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Reduce the static buffer size from the generic default 1260
down to 64 to match the max FIFO size for the cr50 hardware
and reduce the footprint of the driver.
BUG=chrome-os-partner:53336
Change-Id: I6f9f71d501b60299edad4b16cc553a85391a1866
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16664
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Originally I thought it would be cleaner to keep this code in one
place, but as things continue to diverge it ends up being easier
to split this into its own driver. This way the different drivers
in coreboot, depthcharge, and the kernel, can all be standalone
and if one is changed it is easier to modify the others.
This change splits out the cr50 driver and brings along the basic
elements from the existing driver with no real change in
functionality. The following commits will modify the code to make
it consistent so it can all be shared with depthcharge and the
linux kernel drivers.
BUG=chrome-os-partner:53336
Change-Id: I3b62b680773d23cc5a7d2217b9754c6c28bccfa7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16663
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This reverts commit c565f9910707b91fcc7a27bab28806e558bb474d.
|
|
This reverts commit 97a2a1ece152b6d40a524361721405b77c37959d.
|
|
This reverts commit 93c778688f0bf2f90334505a3082a2cd4ce1623a.
|
|
This reverts commit 6f5ceb26b9b3e1455ebbd6192e1d2c832bddc77e.
|
|
This reverts commit 557e1a729a9ca89e814220b6203b7ac0dc446913.
|
|
This reverts commit 1241e7db55aff313e56bf4546d969c11368b08a2.
|
|
This reverts commit a5e419c51187d24818f056327746a18676fe3a20.
|
|
Support reading the ACPI GPE status (on x86) to determine when
the cr50 is ready to return response data or is done processing
written data. If the interrupt is not defined by Kconfig then
it will continue to use the safe delay.
This was tested with reef hardware and a modified cr50 image
that generates interrupts at the intended points.
BUG=chrome-os-partner:53336
Change-Id: I9f78f520fd089cb4471d8826a8cfecff67398bf8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Unify the function names to be consistent throughout the driver
and improve the handling while waiting for data available and
data expected flags from the TPM.
BUG=chrome-os-partner:53336
Change-Id: I7e3912fb8d8c6ad17d1af2d2a7189bf7c0c52c8e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Clean up the mask and timeout handling in the locality functions
that were copied from the original driver.
BUG=chrome-os-partner:53336
Change-Id: Ifa1445224b475aec38c2ac56e15cb7ba7fcd21ea
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Rename the low-level functions from iic_tpm_read/write to
cr50_i2c_read/write to better match the driver name, and pass in the
tpm_chip structure to the low-level read/write functions as it will
be needed in future changes.
BUG=chrome-os-partner:53336
Change-Id: Ib4a68ce1b3a83ea7c4bcefb9c6f002f6dd4aac1f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Use two different timeouts in the driver. The 2ms timeout is needed
to be safe for cr50 to cover the extended timeout that is seen with
some commands. The other at 2 seconds which is a TPM spec timeout.
BUG=chrome-os-partner:53336
Change-Id: I77fdd7ea646b8b2fef449f07e3a08bcce174fe8b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Reduce the static buffer size from the generic default 1260
down to 64 to match the max FIFO size for the cr50 hardware
and reduce the footprint of the driver.
BUG=chrome-os-partner:53336
Change-Id: Ia88facca607f3fd5072d0d986323fde075f15855
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Originally I thought it would be cleaner to keep this code in one
place, but as things continue to diverge it ends up being easier
to split this into its own driver. This way the different drivers
in coreboot, depthcharge, and the kernel, can all be standalone
and if one is changed it is easier to modify the others.
This change splits out the cr50 driver and brings along the basic
elements from the existing driver with no real change in
functionality. The following commits will modify the code to make
it consistent so it can all be shared with depthcharge and the
linux kernel drivers.
BUG=chrome-os-partner:53336
Change-Id: Ia9a65e72519b95f5739e3b7a16b9c2431d64ebe2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
|
