| Age | Commit message (Collapse) | Author |
|---|
|
This allows to configure a default screen rotation in 90-degree
steps. The framebuffer contents will then be displayed rotated,
by the same amount in the other direction; i.e. if you turn the
screen to the left, the picture has to be rotated to the right
to accommodate.
This is only supported by libgfxinit from Skylake / Apollo Lake
on (earlier GPUs didn't support the 90-degree steps anyway) and
it only works with the linear-framebuffer option.
Change-Id: Iac75cefbd34f28c55ec20ee152fe67351cc48653
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
In the HD Audio Specification Rev. 1.0a, every bitfield in the GCAP
register is RO (Read Only). However, it is known that in some Intel
PCHs (e.g 6-series and 7-series, documents 324645 and 326776), some
of the bitfields in the GCAP register are R/WO (Read / Write Once).
GCAP is RO on 5-series PCHs; 8-series and 9-series PCHs have a lock
bit for GCAP elsewhere.
Lock GCAP by reading GCAP and writing back the same value. This has
no effect on platforms that implement GCAP as a RO register or lock
GCAP through a different mechanism.
Change-Id: Id61e6976a455273e8c681dbeb4bad35d57b1a8a2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The QEMU Bochs display driver and the QEMU Firmware Configuration
interface code (in the qemu-i440fx mainboard dir) were written for x86.
These devices are available in QEMU VMs of other architectures as well,
so we want to port them to be independent from x86.
The main problem is that the drivers use x86 port I/O functions to
communicate with devices over PCI I/O space. These are currently not
available for ARM* and RISC-V, although it is often still possible to
access PCI I/O ports over MMIO through a translator.
Add implementations of port I/O functions that work with PCI I/O space
on these architectures as well, assuming there is such a translator at a
known address configured at build-time.
Change-Id: If7d9177283e8c692088ba8e30d6dfe52623c8cb9
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80372
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The CHECK_REV_IN_OPROM_NAME Kconfig option was introduced to solve the
problem of the PCI VID/DID combination of the Picasso iGPU not being
sufficient information to know which VGA BIOS file to run, so a new
function that additionally checks the PCI revision of that device was
introduced. Later it turned out that there might be a case where even
that isn't sufficient, so the soc_is_raven2() function is used in the
remap function to always use the correct VBIOS file.
Picasso is the only SoC that selected the CHECK_REV_IN_OPROM_NAME
Kconfig option, so all other SoCs are unaffected by this change.
Now that we use the VBIOS images with only the PCI VID and DID in the
CBFS file name for Picasso, SeaBIOS will find the VBIOS with the same ID
as the iGPU in CBFS and we don't need the workaround to add a third
VBIOS image via VGA_BIOS_DGPU_* that has the name that SeaBIOS expects.
This will result in SeaBIOS now running the VBIOS that has the same PCI
VID/DID as the hardware which will be the wrong one in the RV2 silicon
showing the PCO silicon PCI VID/DID, but that was also the case with the
VGA_BIOS_DGPU_* workaround where the board's Kconfig just selected one
of the two possible images during build time and hoped that it was the
correct one for that actual hardware. The only board where this patch
might cause a regression compared to the old behavior is the AMD Cereme
reference board with Pollock APU, but I'm not even sure if any coreboot
developer still has one of those boards, so I'm willing to accept that.
To properly solve the problem with SeaBIOS using the correct VBIOS file
in all cases, we'd need to generate that info during coreboot runtime
and somehow pass it to SeaBIOS, but that's out of scope for this patch.
TEST=On Mandolin with PCO silicon, the display output in both SeaBIOS
and Ubuntu still works. Booting Windows 10 via the pre-built EDK2
payload that I'm using also resulted in the display output working.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia6de533c536044698d85404427719b8f534870fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82598
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This options should not be visible on !Intel, !ACPI and !USB4.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ia515d52baead9e151533278c33fda9436ee56168
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79669
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add initial support for multiple PCI segment groups. Instead of
modifying secondary in the bus struct introduce a new segment_group
struct element and keep existing common code.
Since all platforms currently only use 1 segment this is not a
functional change. On platforms that support more than 1 segment the
segment has to be set when creating the PCI domain.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ied3313c41896362dd989ee2ab1b1bcdced840aa8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Provide a default for the ECAM_MMCONF_LENGTH Kconfig option for the
ECAM_MMCONF_BUS_NUMBER option being set to 32.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I01e7da5d49f296dde2de41e23e86e3f49fe78193
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Historically resource allocation in coreboot was 32bit x86 thing. To
remain compatible with this behavior (e.g. to keep 32bit payloads
happy), resource allocation limits resources to 32 bits unless
explicitly overridden. However this behavior is not always appropriate:
e.g. on non x86 platforms the PCIe mem decode window could be above 4G.
Another case on x86 is where the decode window(s) below 4G are not
adequate for fitting all resources and the payload is 64bit
capable (e.g. Linux).
This adds a Kconfig flag to override the behavior to limit resources to
32bit by default and to allocate resources according to the real
hardware limits.
TEST=intel/archercity CRB
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I01218a8a3efc4a5f8ba344808949ca6b8898525f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78331
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
|
|
This option is nowhere selected and there is only a single case left
where it's used. Guarding the check in pci_rom_load() seems like a
bad idea: As the code would be copying all VGA ROMs to the same
location, it would be only working by chance (if the last encoun-
tered ROM is the right one). Hence, drop the guard and always check
for the correct device.
Change-Id: Ib283bf0a65367b99099a3bfcbd27585d44235eb9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79596
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename AZALIA_PLUGIN_SUPPORT to AZALIA_HDA_CODEC_SUPPORT and add a help
text to this Kconfig option to clarify what this option is about.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I71e36869c6ebf77f43ca78f5e451aebfb59f1c74
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
EDK2 seems to have problems at least with the resource allocation for
Intel's IGD. While the investigation is ongoing, disable top-down
allocation by default if the payload is known to be EDK2.
Change-Id: I771d8a3b74b54a043624843a00498225d1f509ad
Signed-off-by: Nico Huber <nico.h@gmx.de>
Ticket: https://ticket.coreboot.org/issues/499
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76373
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
We currently have two competing mechanisms to limit the placement of
resources:
1. the explicit `.limit` field of a resource, and
2. the IORESOURCE_ABOVE_4G flag.
This makes the resource allocator unnecessarily complex. Ideally, we
would always reduce the `.limit` field if we want to "pin" a specific
resource below 4G. However, as that's not done across the tree yet,
we will use the _absence_ of the IORESOURCE_ABOVE_4G flag as a hint
to implicitly lower the `limit` of a resource. In this patch, this
is done inside the effective_limit() function that hides the flag
from the rest of the allocator.
To automatically place resources above 4G if their limit allows it,
we have to allocate from top down. Hence, we disable the prompt for
RESOURCE_ALLOCATION_TOP_DOWN and turn it on by default. Platforms
that are incompatible should be fixed, but can also override the
default as a temporary measure.
One implication of the changes is that we act differently when a
cold-plugged device reports a prefetchable resource with 32-bit
limit. Before this change, we would fail to allocate the resource.
After this change, it forces everything on the same root port below
the 4G line.
A possible solution to get completely rid of the IORESOURCE_ABOVE_4G
flag would be rules to place resources of certain devices below 4G.
For instance, the primary VGA device and storage and HID devices
could be made available to a payload that can only address 32 bits.
For now, effective_limit() provides us enough abstraction as if the
`limit` would be the only variable to consider. With this, we get
rid of all the special handling of above 4G resources during phase 2
of the allocator. Which saves us about 20% of the code :D
An earlier version of this change (commit 117e43611548) had to be
reverted because of missing resource reservations in platform code.
This is worked around now with commit ae81497cb6c7 (device/pci:
Limit default domain memory window).
Change-Id: Ia822f0ce648c7f7afc801d9cb00b6459fe7cebea
Signed-off-by: Nico Huber <nico.h@gmx.de>
Original-reviewed-on: https://review.coreboot.org/c/coreboot/+/65413
Original-reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Original-reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
When the default pci_domain_read_resources() is used,
keep 32-bit memory resources below the limit given by
CONFIG_DOMAIN_RESOURCE_32BIT_LIMIT. This serves as a
workaround for missing/wrong reservations of chipset
resources.
This will help to get more stable results from our own
allocator, but is far from a complete solution. Indvi-
dual platform ASL code also needs to be considered, so
the OS won't assign conflicting resources.
Most platforms have reserved space between 0xfe000000
and the 4G barrier. So use that as a global default.
In case of `soc/intel/common/`, use 0xe0000000 because
this is what is advertised in ACPI and there are traces
of resources below 0xfe000000 that are unknown to core-
boot's C code (PCH_PRESERVED_BASE?).
Tested on QEMU/Q35 and Siemens/Chili w/ and w/o top-
down allocation. Fixes EHCI w/ top-down in QEMU.
Change-Id: Iae0d888eebd0ec11a9d6f12975ae24dc32a80d8c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75102
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The rationale behind this change is that multiple nested bridges using a
lot of bus numbers and IO resources is not likely to be a common hotplug
setup. When there is a large amount of hotplug ports using 32
subordinate busses results in boot failures (e.g. make qemu). 8K IO
busses for hotplug devices is also excessive in most use cases when only
64K is available in total (again make qemu results in failure to
allocate resources but does boot to payload).
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I8371958037d479e7d2053f49814735e15461ca6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74774
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Move D3COLD_SUPPORT to device, so it can be used by multiple
SOCs.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ie92736458ab95374c51346107665dc0fd1e653a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74404
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 655f7362e13ca49e3e13a822c916c7dc52573d74.
Reason for revert: Apparently, the change was not properly reviewed. It
not only contains conflicting name and description of the D3COLD
Kconfig, but also creates a conflict between existing devicetree and
Kconfig options for D3Cold/S3/S0ix.
Change-Id: I56ce8f59f8548fc58bc2b3b07c1314e2eed7061c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Add a paragraph to the help text for VGA_BIOS_ID to explain which PCI ID
needs to be used.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1a0f25481e275b7d190f29f5670cc98443dbe719
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73613
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Add NO_S0IX_SUPPORT for boards that do not support, or do not want
to support S0IX.
As all the boards in the tree that do this, don't support D3Cold,
add D3COLD_SUPPORT that defaults to `n` when NO_S0IX_SUPPORT is
selected to disable D3Cold support.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I03378cc7bb76fd65fcec81018e47f6288d437cd8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
The patch that introduced the selection of software connection manager,
CB:64561 - 060df17f1d (soc/intel/alderlake/acpi: Add Kconfig options for
SCM and FCM) added a default to enable the software configuration
manager directly in the choice.
This leads to warnings when running make menuconfig:
src/soc/intel/alderlake/Kconfig:439:
warning: defaults for choice values not supported
src/soc/intel/meteorlake/Kconfig:337:
warning: defaults for choice values not supported
src/soc/intel/tigerlake/Kconfig:299:
warning: defaults for choice values not supported
I'm not sure why the Kconfig linter didn't catch this, but this
issue is currently breaking the build for me. This patch fixes
it so that instead of setting the default directly, a new Kconfig
value is selected that then sets the default correctly.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I674046a93af8f7c2f3003900804deefa89dae295
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71776
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
A mainboard port needs to:
- select `CONFIG_MAINBOARD_HAS_EARLY_LIBGFXINIT'
- implement the Ada package `GMA.Mainboard' with a single function
`ports' that returns a list of ports to be probed for displays.
- set the desired `GFX_GMA_DEFAULT_MMIO' IO memory address to use
in romstage (and ramstage) for the graphic device.
BUG=b:252792591
BRANCH=firmware-brya-14505.B
TEST=libgfxinit compiles in romstage.
libgfxinit successfully executes in romstage and ramstage using
the requested MMIO setting on skolas.
Change-Id: I3c2101de10dc5df54fe873e43bbe0f1c4dccff44
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70276
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Software Connection Manager doesn't work with Linux 5.13 or later,
resulting in TBT ports timing out. Not advertising this results
in Firmware Connection Manager being used and TBT works
correctly.
Add Kconfig options to chose between SCM (Software Connection
Manager) and FCM (Firmware Connection Manager). FCM is primary, as
it's more compatible save for ChromeOS devices as ChromeOS uses
SCM.
Linux patch:
torvalds/linux@c6da62a
c6da62a219d028de10f2e22e93a34c7ee2b88d03
Tested with StarBook Mk VI (i7-1260P).
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Iac31d37c0873f41f7b14e1051fe214466d1ebdd8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Increase the default linear framebuffer max height/width for desktops
so that native display resolution works properly on 2160p and 1440p
ultrawide displays.
TEST=build/boot google/fizz, verify libgfxinit display init works
properly on 3440x1440p and 3840x2160p displays.
Change-Id: I95a1f1275a4faea195b73997c648023119807958
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
This option is not working so don't advertise it.
Change-Id: I910162756a567289b2484a5445360a3197ae848c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
No platform uses this anymore.
Change-Id: Ifccb59ae45daa8fec41a9a2d46c628ff24a0c998
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69140
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Currently, we're building support for all memory types into every board,
and letting the linker remove anything that isn't needed. This is okay,
but it'd be nice to be able to build in just what's actually needed.
This change adds options to specify both what is used and what is not.
By doing it that way, the default values don't change, but platforms can
start removing support for memory types that are not needed. When all
platforms (SoCs, CPUs and/or Northbridge chips) specify what memory
types they support, the defaults on the options to use a particular
memory type can be set to no, and the options not to use a memory type
can be removed.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I07c98a702e0d67c5ad7bd9b8a4ff24c9288ab569
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Refer to PCI Express Base rev6.0 v1.0, 4.2.7 Link Training and Status
State Rules, Lane Error Status is normal to record the error when link
training. To make sure Lane Error Status is correct in OS runtime,
add a Kconfig PCIEXP_LANE_ERR_STAT_CLEAR that clears the PCIe lane error
status register at the end of PCIe link training.
Test=On Crater Lake, lspci -vvv shows
bb:01.0 PCI bridge: Intel Corporation Device 352a (rev 03)
(prog-if 00 [Normal decode])
Capabilities: [a30 v1] Secondary PCI Express
LnkCtl3: LnkEquIntrruptEn- PerformEqu-
LaneErrStat: LaneErr at lane: 0
Signed-off-by: Wilson Chou <Wilson.Chou@quantatw.com>
Change-Id: I6344223636409d8fc25e365a6375fc81e69f41a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67264
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
The top-down allocation feature was merged prematurely before
platforms that don't report their resources correctly were fixed.
Let's turn it off by default.
Change-Id: I982e6d7355b9e689de10357d6c16ed718705270e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67328
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
This reverts commit 117e436115484f0ce184114b22b716616592e77e.
Depends on top-down allocation to keep the behavior to place
hot-plug reservations above 4G. The latter was merged prema-
turely, though.
Change-Id: I5721cb84b29fc42240dff94f49a94461d88e7fbc
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67329
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
We currently have two competing mechanisms to limit the placement of
resources:
1. the explicit `.limit` field of a resource, and
2. the IORESOURCE_ABOVE_4G flag.
This makes the resource allocator unnecessarily complex. Ideally, we
would always reduce the `.limit` field if we want to "pin" a specific
resource below 4G. However, as that's not done across the tree yet,
we will use the _absence_ of the IORESOURCE_ABOVE_4G flag as a hint
to implicitly lower the `limit` of a resource. In this patch, this
is done inside the effective_limit() function that hides the flag
from the rest of the allocator.
To automatically place resources above 4G if their limit allows it,
we have to allocate from top down. Hence, we disable the prompt for
RESOURCE_ALLOCATION_TOP_DOWN if resources above 4G are requested.
One implication of the changes is that we act differently when a
cold-plugged device reports a prefetchable resource with 32-bit
limit. Before this change, we would fail to allocate the resource.
After this change, it forces everything on the same root port below
the 4G line.
A possible solution to get completely rid of the IORESOURCE_ABOVE_4G
flag would be rules to place resources of certain devices below 4G.
For instance, the primary VGA device and storage and HID devices
could be made available to a payload that can only address 32 bits.
For now, effective_limit() provides us enough abstraction as if the
`limit` would be the only variable to consider. With this, we get
rid of all the special handling of above 4G resources during phase 2
of the allocator. Which saves us about 20% of the code :D
Change-Id: I4c7fcd1f5146f6cc287bd3aa5582da55bc5d6955
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65413
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add option to resource allocator v4 that restores the top-down
allocation approach at the domain level.
This makes it easier to handle 64-bit resources natively. With
the top-down approach, resources that can be placed either above
or below 4G would be placed above, to save precious space below
the 4G boundary.
Change-Id: Iaf463d3e6b37d52e46761d8e210034fded58a8a4
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
coreboot uses TianoCore interchangeably with EDK II, and whilst the
meaning is generally clear, it's not the payload it uses. EDK II is
commonly written as edk2.
coreboot builds edk2 directly from the edk2 repository. Whilst it
can build some components from edk2-platforms, the target is still
edk2.
[1] tianocore.org - "Welcome to TianoCore, the community supporting"
[2] tianocore.org - "EDK II is a modern, feature-rich, cross-platform
firmware development environment for the UEFI and UEFI Platform
Initialization (PI) specifications."
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I4de125d92ae38ff8dfd0c4c06806c2d2921945ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65820
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
coreDOOM is a port of DOOM to libpayload, based on the doomgeneric
source port. It renders the game to the coreboot linear framebuffer,
and loads WAD files from CBFS.
Tested with QEMU i440fx/q35 and a Dell Latitude E6400 using the
libgfxinit provided linear framebuffer.
Project page: https://github.com/nic3-14159/coreDOOM
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Change-Id: Ice0403b003a4b2717afee585f28303c2f5abea5d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Martin L Roth <gaumless@tutanota.com>
|
|
This patch introduces CONFIG_I2C_TRANSFER_TIMEOUT_US,
which controls how long to wait for an I2C devices to
produce/accept all the data bytes in a single transfer.
(The device can delay transfer by stretching the clock of
the ack bit.)
The default value of this new setting is 500ms. Existing
code had timeouts anywhere from tens of milliseconds to a
full second beween various drivers. Drivers can still have
their own shorter timeouts for setup/communication with the
I2C host controller (as opposed to transactions with I2C
devices on the bus.)
In general, the timeout is not meant to be reached except in
situations where there is already serious problem with the
boot, and serves to make sure that some useful diagnostic
output is produced on the console.
Change-Id: I6423122f32aad1dbcee0bfe240cdaa8cb512791f
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Get rid of Kconfig symbol introduced at commit 5d31dfa8
High Definition Audio Specification Revision 1.0a says, there
are 15 SDIWAKE bits.
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ib8b656daca52e21cb0c7120b208a2acdd88625e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62202
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Section 7.8.6 of the PCIe spec (rev 4) indicates that some devices can
indicates support for "Resizable BARs" via a PCIe extended capability.
When support this capability is indicated by the device, the size of
each BAR is determined in a different way than the normal "moving
bits" method. Instead, a pair of capability and control registers is
allocated in config space for each BAR, which can be used to both
indicate the different sizes the device is capable of supporting for
the BAR (powers-of-2 number of bits from 20 [1 MiB] to 63 [8 EiB]), and
to also inform the device of the size that the allocator actually
reserved for the MMIO range.
This patch adds a Kconfig for a mainboard to select if it knows that it
will have a device that requires this support during PCI enumeration.
If so, there is a corresponding Kconfig to indicate the maximum number
of bits of address space to hand out to devices this way (again, limited
by what devices can support and each individual system may want to
support, but just like above, this number can range from 20 to 63) If
the device can support more bits than this Kconfig, the resource request
is truncated to the number indicated by this Kconfig.
BUG=b:214443809
TEST=compile (device with this capability not available yet),
also verify that no changes are seen in resource allocation for
google/brya0 before and after this change.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I14fcbe0ef09fdc7f6061bcf7439d1160d3bc4abf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Currently, the MMCONF Kconfigs only support the Enhanced Configuration
Access mechanism (ECAM) method for accessing the PCI config address
space. Some platforms have a different way of mapping the PCI config
space to memory. This patch renames the following configs to
make it clear that these configs are ECAM-specific:
- NO_MMCONF_SUPPORT --> NO_ECAM_MMCONF_SUPPORT
- MMCONF_SUPPORT --> ECAM_MMCONF_SUPPORT
- MMCONF_BASE_ADDRESS --> ECAM_MMCONF_BASE_ADDRESS
- MMCONF_BUS_NUMBER --> ECAM_MMCONF_BUS_NUMBER
- MMCONF_LENGTH --> ECAM_MMCONF_LENGTH
Please refer to CB:57861 "Proposed coreboot Changes" for more
details.
BUG=b:181098581
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_KOHAKU -x -a -c max
Make sure Jenkins verifies that builds on other boards
Change-Id: I1e196a1ed52d131a71f00cba1d93a23e54aca3e2
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
These issues were found and fixed by codespell, a useful tool for
finding spelling errors.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I5b8ecdfe75d99028fee820a2034466a8ad1c5e63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58080
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sounds like we prefer to have this under drivers/ instead of device/.
Also move all MIPI-related headers out from device/ into their own
directory.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib3e66954b8f0cf85b28d8d186b09d7846707559d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
All boards that are trying to use MIPI panels eventually run into the
problem that they need to store physical parameters and a list of DCS
initialization commands for each panel, and these commands can be very
different (e.g. a large amount of very short commands, a few very large
commands, etc.). Finding a data format to fit all these different cases
efficiently into the same structures keeps being a challenge, and the
Kukui mainboard already once put a lot of effort into designing a
clean, flexible and efficient solution for this. This patch moves that
framework into a common src/device/mipi/ library where it can be used by
other boards as well. (Also, this will hopefully allow us to save some
duplicated work when using the same panel on different boards at some
point.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I877f2b0c7ab984412b288e2ed27f37cd93c70863
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
On Intel 6-series PCHs, the GCAP register is R/WO (Read / Write Once),
and needs to be written to after the HD Audio controller is taken out
of reset. Add a Kconfig option to read and write back GCAP in order to
lock it down. Follow-up commits will select this option when switching
platforms to use common Azalia code, to preserve original behaviour.
Change-Id: I70bab20816fb6c0bf7bff35c3d2f5828cd96172d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The default of 32 buses per hotplug bridge is rather high. Especially
for platforms that limit MMConf space to 64 buses: they run out of
numbers if there is more than a single hotplug bridge.
Lower the default to
* 8 if MMConf is limited to 64 or less buses,
* 16 if MMConf is limited to 128 or less buses.
Change-Id: I06d522dd92ceea9f4798273b26f947a5333800c3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52069
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the AZALIA_MAX_CODECS Kconfig option and use it.
Change-Id: Ibb10c2f2992257bc261e6cb35f11cc4b2d956054
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
It’s good practice to put the unit into the name.
Change-Id: I1493f61d4e495c22f09abf1829bb2eab9b1fd2b6
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
It was commented that the need for the delay was mainly related
to external displays and only with VBIOS execution. Move the
delay such that it is done only when we actually need to execute
the VBIOS aka option rom.
A delay is currently only defined for librem/purism_bdw in
its Kconfig. As the description of the issue sounds like it
would equally happen on other platforms when VBIOS is involved,
promote the Kconfig visible option to global scope.
Change-Id: I4503158576f35057373f003586bbf76af4d59b3d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This is necessary because ASL Memory32Fixed values cannot contain
operations, even if they can be evaluated to constants. Add a sanity
check in pci_mmio_cfg.h to ensure consistency with MMCONF_BUS_NUMBER.
Change-Id: I8f0b5edf166580cc12c1363d8d6b6ef0f2854be9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50033
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Only specify the type of MMCONF_BASE_ADDRESS and MMCONF_BUS_NUMBER once.
Change-Id: Iacd2ed0dae5f1fb6b309124da53b3fa0eef32693
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50032
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Platform can now select VGA_ROM_RUN_DEFAULT Kconfig to perform graphics
initialization for PCI-E based discrete card through VGA OpRom
(SoC or Mainboard user can't select VGA_ROM_RUN directly because
it's part of choice option).
(Note: Some payloads, like SeaBIOS, are also able to run Option ROMs,
so coreboot does not need to enable VGA_ROM_RUN Kconfig)
For payload like depthcharge, create VGA_ROM_RUN_DEFAULT Kconfig
for mainboard to select design with DGPU where OpROM is embedded
inside the DGPU card.
Allow auto selection of VGA_ROM_RUN_DEFAULT from VGA_BIOS Kconfig.
Also NO_GFX_INIT Kconfig to avoid running VGA_ROM_RUN
by default in case SeaBIOS is used.
TEST=Able to get Pre-OS splash screen with AMD Radeon RX 5700 PCI-E
DGPU when mainboard user selects VGA_ROM_RUN_DEFAULT.
Change-Id: Iecb2fcdb105af449bc20ad727759cdef17d5e376
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49016
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Only two definitions are actually used somewhere, the rest is unused.
Change-Id: Iec52d0d47fce6a1ec5455b670824b995a7a34a4c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47407
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic7cacce28f473dda76ca203016dbb8e00149a990
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
As an intermediate step for CB:45150, add an additional Kconfig option
which is used to configure bus mastering for any devices and use
PCI_ALLOW_BUS_MASTER to allow coreboot setting the bus mastering bit in
general.
Change-Id: I33b37a79022007a16e97350db61575b63fa8256b
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45149
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I902915133035fb2adff7edd9c931d4b1d3e7dc40
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Check that nobody misuses the Kconfigs SUBSYSTEM_*_ID. They are meant to
be used for overriding the devicetree subsystem ids locally but shall
not be added to a board's Kconfig. Instead, the devicetree option
`subsystemid` should be used.
Add a linter script for this that finds and warns about such misuse.
Also add a note in the Kconfigs' description.
TEST=CB:45513
Change-Id: I21c021c718154f1396f795a555af47a76d6efe03
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The bus master bit is set at many places in coreboot's code, but the
reason for that is not quite clear. We examined not setting the
bus master bit whereever possible and tried booting without it,
which worked fine for internal PCI devices but not for PCIe. As a PCIe
device we used a Samsung M.2 NVMe SSD.
For security reasons, we would like to disable bus mastering where
possible. Depending on the device, bus mastering might get enabled
by the operating system (e.g. for iGPU) and it might be required for
some devices to work properly. However, the idea is to leave it disabled
and configure the IOMMU first before enabling it.
To have some sort of "backwards compatibility", add a method which
configures bus mastering based on an additional config option. Since
CB:42460 makes usage of this treewide, enable it by default to keep the
current behaviour for now.
Tested with Siemens/Chili, a Coffee Lake based platform.
Change-Id: I876c48ea3fb4f9cf7b6a5c2dcaeda07ea36cbed3
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42459
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kconfig 4.17 started using the $(..) syntax for environment variable
expansion while we want to keep expansion to the build system.
Older Kconfig versions (like ours) simply drop the escapes, not
changing the behavior.
While we could let Kconfig expand some of the variables, that only
splits the handling in two places, making debugging harder and
potentially messing with reproducible builds (e.g. when paths end up
in configs), so escape them all.
Change-Id: Ibc4087fdd76089352bd8dd0edb1351ec79ea4faa
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
|
|
This decouples the linear framebuffer type from the symbols needing it.
Change-Id: I733e630e0aa2fb2947d079caef26253ce443fe91
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42432
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will allow enumerating an xHCI controller to allow dynamically
generating the ACPI device nodes.
BUG=b:154756391
TEST=Boot trembyle and see capabilities printed on console
xHCI Supported Protocol:
Major: 0x2, Minor: 0x0, Protocol: 'USB '
Port Offset: 1, Port Count: 2
xHCI Supported Protocol:
Major: 0x3, Minor: 0x10, Protocol: 'USB '
Port Offset: 3, Port Count: 1
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I3065c3fffad01b5378a55cfe904f971079b13d0f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
4G boundary""
This reverts commit e15f352039a371156ceef37f0434003228166e99.
Reason for revert: Resource allocator is split into old(v3) and
new(v4). So, this change to provide an option to allocate prefetch
memory above 4G boundary can be added back. Since the support for
allocating above 4G boundary is available only in resource allocator
v4, Kconfig option is accordingly updated to add depends on
RESOURCE_ALLOCATOR_V4.
Change-Id: I94e5866458c79c2719fd780f336fb5da71a7df66
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41467
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change disables the old resource allocator by default and instead
uses the new v4 resource allocator. Only the chipsets that explicitly
select RESOURCE_ALLOCATOR_V3 will continue to use the old v3 resource
allocator.
Change-Id: I2ab9f1d612b5f193f058011a18b1d6373e09f788
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41445
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
|
|
This change adds back support for the resource allocator using
multiple ranges as originally landed in CB:39486(commit hash 3b02006)
and reverted in CB:41413(commit hash 6186cbc). The new resource
allocator can be selected by Kconfig option RESOURCE_ALLOCATOR_V4. It
was identified that there are some AMD chipsets in the tree that do
not really work well with the dynamic resource allocation. Until these
chipsets are fixed, old (v3) and new (v4) of the resource allocator
need to live side-by-side in the tree. There were some other chipsets
in the tree which originally demonstrated problems with the new
resource allocator, but have been since fixed in the tree.
This change picks up the same additions as performed in CB:39486 along
with the following changes:
1. Changes to avoid fixed resources in the entire tree. Use of
search_bus_resources() is replaced with a walk of the entire tree
in avoid_fixed_resources(). This is required to ensure that all fixed
resources added to any device (including domain) are taken into
consideration to avoid overlap during dynamic resource allocation.
2. Changes to set up alignment for memranges when initializing
them. This is done to ensure that the right granularity is used for
IORESOURCE_IO(no special alignment) and IORESOURCE_MEM(4KiB) resource
requests.
3. mark_resource_invalid() is dropped as the resource no longer needs
to be marked in any special way if allocation is not being
done. Instead setting of IORESOURCE_ASSIGNED flag is skipped in this
case.
4. initialize_memranges() is updated to check IORESOURCE_ASSIGNED
instead of base == limit.
Original commit message:
This change updates the resource allocator in coreboot to allow using
multiple ranges for resource allocation rather than restricting
available window to a single base/limit pair. This is done in
preparation to allow 64-bit resource allocation.
Following changes are made as part of this:
a) Resource allocator still makes 2 passes at the entire tree. The
first pass is to gather the resource requirements of each device
under each domain. It walks recursively in DFS fashion to gather the
requirements of the leaf devices and propagates this back up to the
downstream bridges of the domain. Domain is special in the sense that
it has fixed resource ranges. Hence, the resource requirements from
the downstream devices have no effect on the domain resource
windows. This results in domain resource limits being unmodified after
the first pass.
b) Once the requirements for all the devices under the domain are
gathered, resource allocator walks a second time to allocate resources
to downstream devices as per the requirements. Here, instead of
maintaining a single window for allocating resources, it creates a
list of memranges starting with the resource window at domain and then
applying constraints to create holes for any fixed resources. This
ensures that there is no overlap with fixed resources under the
domain.
c) Domain does not differentiate between mem and prefmem. Since they
are allocated space from the same resource window at the domain level,
it considers all resource requests from downstream devices of the
domain independent of the prefetch type.
d) Once resource allocation is done at the domain level, resource
allocator walks down the downstream bridges and continues the same
process until it reaches the leaves. Bridges have separate windows for
mem and prefmem. Hence, unlike domain, the resource allocator at
bridge level ensures that downstream requirements are satisfied by
taking prefetch type into consideration.
e) This whole 2-pass process is performed for every domain in the
system under the assumption that domains do not have overlapping
address spaces.
Noticeable differences from previous resource allocator:
a) Changes in print logs observed due to flows being slightly
different.
b) Base, limit and size of domain resources are no longer updated
based on downstream requirements.
c) Memranges are used instead of a single base/limit pair for
determining resource allocation.
d) Previously, if a resource request did not fit in the available
base/limit window, then the resource would be allocated over DRAM or
any other address space defeating the principle of "no overlap". With
this change, any time a resource cannot fit in the available ranges,
it complains and ensures that the resource is effectively disabled by
setting base same as the limit.
e) Resource allocator no longer looks at multiple links to determine
the right bus for a resource. None of the current boards have multiple
buses under any downstream device of the domain. The only device with
multiple links seems to be the cpu cluster device for some AMD
platforms.
Change-Id: Ide4d98528197bb03850a8fb4d73c41cd2c0195aa
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41443
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change moves the resource allocator functions out of device.c
and into two separate files:
1. resource_allocator_v3.c: This is the old implementation of
resource allocator that uses a single window for resource
allocation. It is required to support some AMD chipsets that do not
provide an accurate map of allocated resources by the time the
allocator runs. They work fine with the old allocator since it
restricts itself to allocations in a single window at the top of the
4G space.
2. resource_allocator_common.c: This file contains the functions that can
be shared by the old and new resource allocator.
Entry point into the resource allocation is allocate_resources() which
can be implemented by both old and new allocators. This change also
adds a Kconfig option RESOURCE_ALLOCATOR_V3 which enables the old
resource allocator. This config option is enabled by default
currently, but in the following CLs this will be enabled only for the
broken boards.
Reason for this split: Both the old and new resource allocators need
to be retained in the tree until the broken chipsets are fixed.
Change-Id: I2f5440cf83c6e9e15a5f22e79cc3c66aa2cec4c0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41442
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I8a207e30a73d10fe67c0474ff11324ae99e2cec6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41360
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit dcbf6454b6d2d9b3627a14126ef20ed4b9c7d954.
Reason for revert: Resource allocator patches need to be reverted
until the AMD chipsets can be fixed to handle the resource allocation
flow correctly.
Change-Id: I58c9fff1a18ea1c9941e29c2c6e60e338c517c30
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
|
|
This change adds a Kconfig option to request allocation of prefetch
memory for hotplug devices above the 4G boundary. In order to
select this option by default and still allow users to disable this if
required, another option is added to request allocation of prefetch
memory below 4G boundary which defaults to n but can be overriden
by mainboards.
Without this change, if the number of pciexp bridges supporting
hot-plug is more than 4 or if the reserved prefetch memory size for
hot-plug cases was increased, then the resource allocator would fail
to satisfy the resource requirement below 4G boundary.
BUG=b:149186922
TEST=Enabled resource allocation above 4G for prefetch memory on volteer
and verified that it gets allocated above 4G boundary.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I061d935eef9fcda352230b03b5cf14e467924e50
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39489
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Used commands:
perl -i -p0e 's|\/\*[\s*]*.*is free software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and\/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-2.0-only */|' $(cat filelist)
perl -i -p0e 's|\/\*[\s*]*.*is[\s*]*free[\s*]*software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*either[\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License,[\s*]*or[\s*]*.at[\s*]*your[\s*]*option.[\s*]*any[\s*]*later[\s*]*version.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-2.0-or-later */|' $(cat filelist)
perl -i -p0e 's|\/\*[\s*]*.*is[\s*#]*free[\s*#]*software[;:,][\s*#]*you[\s*#]*can[\s*#]*redistribute[\s*#]*it[\s*#]*and/or[\s*#]*modify[\s*#]*it[\s*#]*under[\s*#]*the[\s*#]*terms[\s*#]*of[\s*#]*the[\s*#]*GNU[\s*#]*General[\s*#]*Public[\s*#]*License[\s*#]*as[\s*#]*published[\s*#]*by[\s*#]*the[\s*#]*Free[\s*#]*Software[\s*#]*Foundation[;:,][\s*#]*either[\s*#]*version[\s*#]*3[\s*#]*of[\s*#]*the[\s*#]*License[;:,][\s*#]*or[\s*#]*.at[\s*#]*your[\s*#]*option.[\s*#]*any[\s*#]*later[\s*#]*version.[\s*#]*This[\s*#]*program[\s*#]*is[\s*#]*distributed[\s*#]*in[\s*#]*the[\s*#]*hope[\s*#]*that[\s*#]*it[\s*#]*will[\s*#]*be[\s*#]*useful[;:,][\s*#]*but[\s*#]*WITHOUT[\s*#]*ANY[\s*#]*WARRANTY[;:,][\s*#]*without[\s*#]*even[\s*#]*the[\s*#]*implied[\s*#]*warranty[\s*#]*of[\s*#]*MERCHANTABILITY[\s*#]*or[\s*#]*FITNESS[\s*#]*FOR[\s*#]*A[\s*#]*PARTICULAR[\s*#]*PURPOSE.[\s*#]*See[\s*#]*the[\s*#]*GNU[\s*#]*General[\s*#]*Public[\s*#]*License[\s*#]*for[\s*#]*more[\s*#]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-3.0-or-later */|' $(cat filelist)
perl -i -p0e 's|(\#\#*)[\w]*.*is free software[:;][\#\s]*you[\#\s]*can[\#\s]*redistribute[\#\s]*it[\#\s]*and\/or[\#\s]*modify[\#\s]*it[\s\#]*under[\s \#]*the[\s\#]*terms[\s\#]*of[\s\#]*the[\s\#]*GNU[\s\#]*General[\s\#]*Public[\s\#]*License[\s\#]*as[\s\#]*published[\s\#]*by[\s\#]*the[\s\#]*Free[\s\#]*Software[\s\#]*Foundation[;,][\s\#]*version[\s\#]*2[\s\#]*of[\s\#]*the[\s\#]*License.*[\s\#]*This[\s\#]*program[\s\#]*is[\s\#]*distributed[\s\#]*in[\s\#]*the[\s\#]*hope[\s\#]*that[\s\#]*it[\s\#]*will[\#\s]*be[\#\s]*useful,[\#\s]*but[\#\s]*WITHOUT[\#\s]*ANY[\#\s]*WARRANTY;[\#\s]*without[\#\s]*even[\#\s]*the[\#\s]*implied[\#\s]*warranty[\#\s]*of[\#\s]*MERCHANTABILITY[\#\s]*or[\#\s]*FITNESS[\#\s]*FOR[\#\s]*A[\#\s]*PARTICULAR[\#\s]*PURPOSE.[\#\s]*See[\#\s]*the[\#\s]*GNU[\#\s]*General[\#\s]*Public[\#\s]*License[\#\s]*for[\#\s]*more[\#\s]*details.\s(#* *\n)*|\1 SPDX-License-Identifier: GPL-2.0-only\n\n|' $(cat filelist)
perl -i -p0e 's|(\#\#*)[\w*]*.*is free software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and\/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.\s(#* *\n)*|\1 SPDX-License-Identifier: GPL-2.0-only\n\n|' $(cat filelist)
Change-Id: Ia01908544f4b92a2e06ea621eca548e582728280
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41178
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change Graphics Init default for RUN_FSP_GOP to depend on
INTEL_GMA_HAVE_VBT rather than INTEL_GMA_ADD_VBT, since
RUN_FSP_GOP selects INTEL_GMA_ADD_VBT for several Intel SoC's.
Test: create default config for gogle/cyan, RUN_FSP_GOP
still default display init selection but no more circular
dependency warning from config.
Change-Id: I8b978d9938c3d0024d4dd40000b988430664cee7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Adjust the defaults for Graphics Initialization so
that the "best" option for a board is selected by default.
Net effect is to select RUN_FSP_GOP over VGA_ROM_RUN
in cases where the platform supports GOP init and the
mainboard has a VBT file included.
Test: run 'make menuconfig' and check default Display
Init option for google/cyan, observe RUN_FSP_GOP is default.
Change-Id: I2184dbdd943d035d1682b3ae7bd8d005221434b1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
AMD's Family 17h SOCs have the same vendor and device IDs for
their graphics blocks, but need different video BIOSes. The
only difference is the revision number.
Add a Kconfig option that allows us to add the revision number
of the graphics device to the PCI option rom saved in CBFS.
Because searching CBFS takes a non-trivial amount of time,
only enable the option if it's needed. If it's not used, or
if nothing matches, the check will fall through and search for
an option rom with no version.
BUG=b:145817712
TEST=With surrounding patches, loads dali vbios
Change-Id: Icb610a2abe7fcd0f4dc3716382b9853551240a7a
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/2013181
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Picasso and Dali need different video bioses even though they use the
same code in most other places.
The Kconfig symbol names are changed from the downstream commit to make
them more consistent with current coreboot code.
BUG=b:145817712
TEST=Build Dali vBIOS into the coreboot image
Change-Id: Ide0d061fda0abc78a74ddf97ba81fc3cf2b02e4f
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/1956534
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Automatically select the linear framebuffer mode option if
available when Tianocore selected as payload, since VGA text
mode will not work properly with the default Tianocore payload.
Change-Id: Ic36fd035526f3efd00ffa12ad613fbac304b18cf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Also replace 'BIOS' by coreboot when the image is 'coreboot.rom'.
Change-Id: I8303b7baa9671f19a036a59775026ffd63c85273
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change adds support for allocating resources for PCI express hotplug
bridges when PCIEXP_HOTPLUG is selected. By default, this will add 32 PCI
subordinate numbers (buses), 256 MiB of prefetchable memory, 8 MiB of
non-prefetchable memory, and 8 KiB of I/O space to any device with the
PCI_EXP_SLTCAP_HPC bit set in the PCI_EXP_SLTCAP register, which
indicates hot-plugging capability. The resource allocation is configurable,
please see the PCIEXP_HOTPLUG_* variables in src/device/Kconfig.
In order to support the allocation of hotplugged PCI buses, a new field
is added to struct device called hotplug_buses. This is defaulted to
zero, but when set, it adds the hotplug_buses value to the subordinate
value of the PCI bridge. This allows devices to be plugged in and
unplugged after boot.
This code was tested on the System76 Darter Pro (darp6). Before this
change, there are not enough resources allocated to the Thunderbolt
PCI bridge to allow plugging in new devices after boot. This can be
worked around in the Linux kernel by passing a boot param such as:
pci=assign-busses,hpbussize=32,realloc
This change makes it possible to use Thunderbolt hotplugging without
kernel parameters, and attempts to match closely what our motherboard
manufacturer's firmware does by default.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I500191626584b83e6a8ae38417fd324b5e803afc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35946
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The guarded prototypes are no longer implemented in the
tree.
Change-Id: I5bfedde2aaf691826e7537eceb8578a855800ea2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Make sure display can't be selected by accident when NO_GFX_INIT is selected.
Change-Id: Iec5a47f84b8c776a45edc6f4b31a03b9ac714b4e
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This should be defined by mainboard. Add a dummy
default to fix master while HyperTransport files
are still around referencing this.
Change-Id: I58188a200a2cad5fa20affee1844117ba71ac338
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37036
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This has nothing to do with console options.
This also improves the help text to reflect what it actually does.
Change-Id: I039f4f6bbe144769d6a362192b225838ed3d9d43
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
There are mainboards that do not have any graphics ports connected to
the SoC. It would be senseless to initialize the iGD, thus add a new
mainboard Kconfig to hide the GOP option.
Change-Id: Ica3b3a7a0c8120c95412369a24d8d669fb59fded
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Additional cleanup - Unify "Inc" to "Inc." and "LLC." to "LLC"
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ie03a3ce1f6085494bd5f38da76e2467970cf301a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Every vga init implementation needs to cache the framebuffer state
to be able to fill the lb_framebuffer struct later on in the
fill_lb_framebuffer call. Showing the bootsplash afterwards
guarantees to have the same interface into all the vga drivers.
This is by far from ideal, as it only allows for a single driver at
compile-time and should be adapted in the future.
It was tested on the wip razer blade stealth using vgabios @ 1280x1024
and also in Qemu @ 1280x1024.
By default the qemu framebuffer will be initialized in 800x600@32.
This can be overwriten by configuration by setting
CONFIG_DRIVERS_EMULATION_QEMU_BOCHS_{X,Y}RES .
Change-Id: I4bec06d22423627e8f429c4b47e0dc9920f1464e
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Building for ChromeOS implies the use of Depthcharge which doesn't
support legacy text mode.
Change-Id: I7fd82bfed1e59de2de75419cfaea6f0c19cfdf5e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34483
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We might want to make use of libgfxinit functions without using it for
actual graphics init.
Change-Id: I29c3b19989acb678d0d447e83d38bad9d584caa9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31455
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the way of adding the discrete VGA OpROM at config UI (alternative to
./cbfstool ./cb.rom add -f vgabios_dgpu.bin -n pci1002,6663.rom -t optionrom )
DGPU options are accessible only if CONFIG_VGA_BIOS is enabled.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I0a7bf0fe95c833cf3df0c7cb20fc27b6ab218c5a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change default VESA/native framebuffer mode (needed for bootsplash and
graphical framebuffer console) from 117h (1024x768 64k-color (5:6:5))
to 118h (1024x768 16.8M-color (8:8:8)) mode.
This provides console output at Lenovo G505S even if e.g. GRUB is the
payload, while it is unlikely to cause any downsides for the other
boards.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: Ia348199bbd430532b1399706dd84490c9680b5f5
Reviewed-on: https://review.coreboot.org/c/31595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add maximum width and height options and set the default to 2560x1600
(WQXGA). The framebuffer will be scaled up to the displays' native
resolutions. So this should help with tiny fonts on high-DPI displays.
For laptops, reasonable defaults can be set at the mainboard level.
Change-Id: I47fba063629260c3a2854caf7a73f1a1e933d063
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
These chips are still using LATE_CBMEM which was agreed upon to
be removed after release 4.7. It is now more than 1 year later
and they still linger around.
The work and review to bring this code up to date can happen on
the 4.9 branch and then squashed together and merged back into
mainline when done.
Change-Id: I11290a5e92397b9b7e7e5a19b029278e728671a3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
POWER8 is a specific implementation of ppc64, which is by now outdated
(POWER9 has been on the market for a while). Rename arch/power8/ to
potentially cover a wider range of hardware.
TEST=Toolchains built before/after this commit can build coreboot for
emulation/qemu-power8 from before/after this commit.
Change-Id: I2d6f08b12a9ffc8a652ddcd6f24ad85ecb33ca52
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
|
|
Shuffle words and drop the _DATA_FILE suffix.
Change-Id: I0b0d50ea729e5580c0bc7b43f250ff387ce59cfc
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This adds a INTEL_GMA_VBT_HAVE_DATA_FILE Kconfig option for the path
to point to the mainboard dir and to select
INTEL_GMA_ADD_VBT_DATA_FILE by default.
Change-Id: I730cb0737945631e2d5379a9e26b8c039ec6dc49
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/26653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The yabel emulator depends on IO ports, that aren't available on
ARM and MIPS. Add additional dependencies to fix compilation errors
with the default configuration.
Change-Id: If0e28b356c01cb3ae0739a54aa3531a2acedbfbb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/26754
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
FSP_GOP needs a vbt.bin to work but before this patch it was able to
build with the default configuration which was an empty path for
vbt.bin.
To make Jenkins happy don't select FSP_GOP by default, at least until
all boards have the proper vbt blobs in the blobs repo.
Change-Id: Ibc36d6d4dd1a56c53819b169e6f4799ce3c23e03
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Certain platforms require that the option rom always needs to be
ran in order for display to work correctly. Therefore, provide
this ability for the platform to select such that we force option
rom loading.
BUG=b:72400950
Change-Id: I597bc8af7ac8b68fe8505aac5f1c7e1ccd34ac27
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23505
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
cpu/intel/socket_mFCBGA479
northbridge/intel/i82830
Mainboards:
mainboard/rca/rm4100
mainboard/thomson/ip1000
Change-Id: I9574179516c30bb0d6a29741254293c2cc6f12e9
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22032
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Move ADD_VBT_DATA_FILE to "Devices" menu and rename it to
INTEL_GMA_ADD_VBT_DATA_FILE.
Depend on Intel platforms to avoid confusing users of non-Intel platforms.
The Intel GMA driver will use the vbt.bin, if present, to fill the
ACPI OpRegion.
Change-Id: I688bac339c32e9c856642a0f4bd5929beef06409
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The new config choice is called RUN_FSP_GOP. Some things had to happen
on the road:
* Drop confusing config GOP_SUPPORT,
* Add HAVE_FSP_GOP to chipsets that support it,
* Make running the GOP an option for FSP2.0 by returning 0
in random VBT getters.
Change-Id: I92f88424004a4c0abf1f39cc02e2a146bddbcedf
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Provide all gfx init methods as a Kconfig `choice`. This elimates the
option to select native gfx init along with running a Video BIOS. It's
been only theoretically useful in one corner case: Hybrid graphics
where only one controller is supported by native gfx init. Though I
suppose in that case it's fair to assume that one would use SeaBIOS to
run the VBIOS.
For the case that we want the payload to initialize graphics or no
pre-boot graphics at all, the new symbol NO_GFX_INIT was added to the
choice. If multiple options are available, the default is chosen as
follows:
* NO_GFX_INIT, if we add a Video BIOS and the payload is SeaBIOS,
* VGA_ROM_RUN, if we add a Video BIOS and the payload is not SeaBIOS,
* NATIVE_VGA_INIT, if we don't add a Video BIOS.
As a side effect, libgfxinit is now an independent choice.
Change-Id: I06bc65ecf3724f299f59888a97219fdbd3d2d08b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
MAINBOARD_FORCE_NATIVE_VGA_INIT is to be selected instead of the user
option MAINBOARD_DO_NATIVE_VGA_INIT. The distinction is necessary to
use the latter in a choice.
Change-Id: I689aa5cadea9e1091180fd38b1dc093c6938d69c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Make the "Display" menu a submenu of "Devices", place it below the
graphics options and reorder options by their dependencies.
Change-Id: I9de3d8f76ae10b0a77678ce2d71f840fac32379c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19806
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Rename `FRAMEBUFFER_KEEP_VESA_MODE` to `LINEAR_FRAMEBUFFER` and put
it together with new `VGA_TEXT_FRAMEBUFFER` into a choice. There are
two versions of `LINEAR_FRAMEBUFFER` that differ only in the prompt
and help text (one for `HAVE_VBE_LINEAR_FRAMEBUFFER` and one for
`HAVE_LINEAR_FRAMEBUFFER`). Due to `kconfig_lint` we have to model
that with additional symbols.
Change-Id: I9144351491a14d9bb5e650c14933b646bc83fab0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
It's only used for VGA ROMs.
Change-Id: I898765f79cbf5ccce871a3598b56eda83e5efaca
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Like HAVE_VGA_TEXT_FRAMEBUFFER, these are selected by graphics drivers
that support a linear framebuffer. Some related settings moved to the
drivers (i.e. for rockchip/rk3288 and nvidia/tegra124) since they are
hardcoded.
Change-Id: Iff6dac5a5f61af49456bc6312e7a376def02ab00
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
