Age | Commit message (Collapse) | Author |
|
It was found that the Haswell reference code was smashing through the
stack into the reference code's heap implementation. The reason for this
is because our current CAR allocation is too small. Moreover there are
quite a few things to coordinate between 2 code bases to get correct.
This commit separates the CAR into 2 parts:
1. MRC CAR usage.
2. Coreboot CAR usage.
Pointers from one region can be passed between the 2 modules, but one
should not be able to affect the others as checking has been put into
place in both modules.
The CAR size has effectively been doubled from 0x20000 (128 KiB) to
0x40000 (256KiB). Not all of that increase was needed, but enforcing
a power of 2 size only utilizes 1 MTRR.
Old CAR layout with a single contiguous stack with the region starting
at CONFIG_DCACHE_RAM_BASE:
+---------------------------------------+ Offset CONFIG_DCACHE_RAM_SIZE
| MRC global variables |
| CONFIG_DCACHE_RAM_MRC_VAR_SIZE bytes |
+---------------------------------------+
| ROM stage stack |
| |
| |
+---------------------------------------+
| MRC Heap 30000 bytes |
+---------------------------------------+
| ROM stage console |
| CONFIG_CONSOLE_CAR_BUFFER_SIZE bytes |
+---------------------------------------+
| ROM stage CAR_GLOBAL variables |
+---------------------------------------+ Offset 0
There was some hard coded offsets in the reference code wrapper to start
the heap past the console buffer. Even with this commit the console
can smash into the following region depending on what size
CONFIG_CONSOLE_CAR_BUFFER_SIZE is.
As noted above This change splits the CAR region into 2 parts starting
at CONFIG_DCACHE_RAM_BASE:
+---------------------------------------+
| MRC Region |
| CONFIG_DCACHE_RAM_MRC_VAR_SIZE bytes |
+---------------------------------------+ Offset CONFIG_DCACHE_RAM_SIZE
| ROM stage stack |
| |
| |
+---------------------------------------+
| ROM stage console |
| CONFIG_CONSOLE_CAR_BUFFER_SIZE bytes |
+---------------------------------------+
| ROM stage CAR_GLOBAL variables |
+---------------------------------------+ Offset 0
Another variable was add, CONFIG_DCACHE_RAM_ROMSTAGE_STACK_SIZE,
which represents the expected stack usage for the romstage. A marker
is checked at the base of the stack to determine if either the stack
was smashed or the console encroached on the stack.
Change-Id: Id76f2fe4a5cf1c776c8f0019f406593f68e443a7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2752
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The SMM handler resides in the TSEG region which is far above
CONFIG_RAM_TOP (which is the highest cacheable address) before
MTRRs are setup. This means that calling initialize_cpus() before
performing MTRR setup on the BSP means the SMM handler is copied
using uncacheable accesses.
Improve the SMM handler setup path by enabling performing MTRR setup on
for the BSP before the call to initialize_cpus(). In order to do this
the haswell_init() function was split into 2 paths: BSP & AP paths.
There is a cpu_common_init() that both call to perform similar
functionality. The BSP path in haswell_init() then starts the APs using
intel_cores_init(). The AP path in haswell_init() loads microcode and
sets up MTRRs.
This split will be leveraged for future support of bringing up APs in
parallel as well as adhering to the Haswell MP initialization
requirements.
Change-Id: Id8e17af149e68d708f3d4765e38b1c61f7ebb470
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2746
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The configure_mca() function was hard coding the number of
banks the cpu supported. Query this dynamically so that it
no longer clears only 7 banks.
Change-Id: I33fce8fadc0facd1016b3295faaf3ae90e490a71
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2745
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This just moves the definiton of CORE_THREAD_COUNT_MSR so
that future code can utilize it.
Change-Id: I15a381090f21ff758288f55dc964b6694feb6064
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2744
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This commit adds support for using the SMM modules for haswell-based
boards. The SMI handling was also refactored to put the relocation
handler and permanent SMM handler loading in the cpu directory. All
tseg adjustment support is dropped by relying on the SMM module support
to perform the necessary relocations.
Change-Id: I8dd23610772fc4408567d9f4adf339596eac7b1f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2728
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Haswell CPUs require a FIT table in the firmware. This commit
adds rudimentary support for a FIT table. The number of entries
in the table is based on a configuration option. The code only
generates a type 0 entry. A follow-on tool will need to be developed
to populate the FIT entries as well as checksumming the table.
Verified image has a FIT pointer and table when option is selected.
Change-Id: I3a314016a09a1cc26bf1fb5d17aa50853d2ef4f8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2642
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This adds microcode ffff000a and the CPUIDs for ULT.
Change-Id: I341c1148a355d8373b31032b9f209232bd03230a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2647
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The IA32_ENERGY_PERFORMANCE_BIAS MSR can only be read or written
to if the CPU supports it. The support is indicated by ECX[3] for
cpuid(6). Without this guard, some Haswell parts would GP# fault
in this routine.
No more GP# while running on haswell CRBs.
Change-Id: If41e1e133e5faebb3ed578cba60743ce7e1c196f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2639
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore,
the southbridge support is included as well. The basis for this code is
the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires
more attention, but this is a good starting point.
This code partially gets up through the romstage just before training
memory on a Haswell reference board.
Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2616
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Models 6ex and 6fx select UDELAY_LAPIC so cannot select
contradicting UDELAY_TSC here.
Model 1067x requires speedstep.
Change-Id: I69d3ec8085912dfbe5fe31c81fa0a437228fa48f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2525
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
The name lapic_cluster is a bit misleading, since the construct is not local
APIC specific by concept. As implementations and hardware change, be more
generic about our naming. This will allow us to support non-x86 systems without
adding new keywords.
Change-Id: Icd7f5fcf6f54d242eabb5e14ee151eec8d6cceb1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
And move the corresponding #define to speedstep.h
Change-Id: I8c884b8ab9ba54e01cfed7647a59deafeac94f2d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2339
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In particular:
MSR_PMG_CST_CONFIG_CONTROL
MSR_PMG_IO_BASE_ADDR
MSR_PMG_IO_CAPTURE_ADDR
Change-Id: Ief2697312f0edf8c45f7d3550a7bedaff1b69dc6
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2337
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add a comment explaining that the existing lock bit logic is correct
and "as designed" even though the manual states otherwise. This way
people don't have to "just know" what is going on.
Change-Id: I14e6763abfe339e034037b73db01d4ee634bb34d
Signed-off-by: Mike Frysinger <vapier@chromium.org>
Reviewed-on: http://review.coreboot.org/2326
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Summary:
Isolate CBFS underlying I/O to board/arch-specific implementations as
"media stream", to allow loading and booting romstage on non-x86.
CBFS functions now all take a new "media source" parameter; use
CBFS_DEFAULT_MEDIA if you simply want to load from main firmware.
API Changes:
cbfs_find => cbfs_get_file.
cbfs_find_file => cbfs_get_file_content.
cbfs_get_file => cbfs_get_file_content with correct type.
CBFS used to work only on memory-mapped ROM (all x86). For platforms like ARM,
the ROM may come from USB, UART, or SPI -- any serial devices and not available
for memory mapping.
To support these devices (and allowing CBFS to read from multiple source
at the same time), CBFS operations are now virtual-ized into "cbfs_media". To
simplify porting existing code, every media source must support both "reading
into pre-allocated memory (read)" and "read and return an allocated buffer
(map)". For devices without native memory-mapped ROM, "cbfs_simple_buffer*"
provides simple memory mapping simulation.
Every CBFS function now takes a cbfs_media* as parameter. CBFS_DEFAULT_MEDIA
is defined for CBFS functions to automatically initialize a per-board default
media (CBFS will internally calls init_default_cbfs_media). Also revised CBFS
function names relying on memory mapped backend (ex, "cbfs_find" => actually
loads files). Now we only have two getters:
struct cbfs_file *entry = cbfs_get_file(media, name);
void *data = cbfs_get_file_content(CBFS_DEFAULT_MEDIA, name, type);
Test results:
- Verified to work on x86/qemu.
- Compiles on ARM, and follow up commit will provide working SPI driver.
Change-Id: Iac911ded25a6f2feffbf3101a81364625bb07746
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The use of ramstage.a required the build system to handle some
object files in a special way, which were put in the drivers
class.
These object files didn't provide any symbols that were used
directly (but only via linker magic), and so the linker never
considered them for inclusion.
With ramstage.a gone, we can drop this special class, too.
Change-Id: I6f1369e08d7d12266b506a5597c3a139c5c41a55
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Updating microcode on several threads in a core at once
can be harmful. Hence add a spinlock to make sure that
does not happen.
Change-Id: I0c9526b6194202ae7ab5c66361fe04ce137372cc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1778
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There are some function dependancies that didn't work
when MAX_CPU was set to 1 and the build would fail.
Change-Id: I033a42056f7b48a40316e03772ed89ad9cb013fe
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1819
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Adding an entry for 0x306a0 will make sure that all
CPUs with CPUIDs 0x306aX will execute the driver (analog to
Sandybridge behavior)
Change-Id: I0353f3a48ecfd41274fdf6ee302c7d34482f1b5b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1783
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The VMX MSR may come up with random values and needs to be
initialized to zero. This was done incorrectly in finalize_smm.
It must be done on a per core basis in the general CPU init.
This touches all Sandybridge and Ivybridge configs.
Change-Id: I015352d0f8e2ebe55ac0a5e9c5bbff83bd2ff86b
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1794
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The MSR for VMX can start with a random value and needs to be
cleared by coreboot. I am reverting this change, as
it handles almost everything and doing a follow-on change to fix
the improper clearing of the MSR.
Change-Id: Ibad7a27b03f199241c52c1ebdd2b6d4e81a18a4e
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1793
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The reporting of cores and threads in the system was a bit
ambiguous. This patch makes it clearer.
Change-Id: Ia05838a53f696fbaf78a1762fc6f4bf348d4ff0e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1786
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
To allow easy experimentation with thermals, leave power control
registers unlocked.
Change-Id: Ia53065f3f220c2faed58e7d53e60c3f169ae58ec
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Reviewed-on: http://review.coreboot.org/1688
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Change-Id: I853454e8f5617fb7af5dddd7288bdeeacc7b1b8e
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1663
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
All of these capabilities exist on all CPUs supported on
this socket.
Change-Id: I54f34e48e34bb6ab5b9954ab7ece8c2c3a1a8e67
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1664
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This adds proper support for turbo and super-low-frequency modes.
Calculation of the p-states has been rewritten and moved into an
extra file speedstep.c so it can be used for non-acpi stuff like
EMTTM table generation.
It has been tested with a Core2Duo T9400 (Penryn) and a Core Duo T2300
(Yonah) processor.
Change-Id: I5f7104fc921ba67d85794254f11d486b6688ecec
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1658
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I3efef6bc8f519382ffdd92eb10b4bcd1a4361ba9
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1657
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We parsed the MSR the wrong way, and didn't support some valid values.
Change-Id: Ia42e3de05dd76b6830aaa310ec82031d36def3a0
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1656
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We had only some MSR definitions in there, which are used in speedstep
related code. I think speedstep.h is the better and less confusing place
for these.
Change-Id: I1eddea72c1e2d3b2f651468b08b3c6f88b713149
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1655
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ia7ef3a4cbc3638a9c9a48b297e392e4e655b6e6b
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: http://review.coreboot.org/1581
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I7a49d5fc13fb605a47c3c1662758ebd5935e7780
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1564
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Also deletes files not included in build:
src/southbridge/amd/cimx/sb700/chip_name.c
src/southbridge/amd/cimx/sb800/chip_name.c
src/southbridge/amd/cimx/sb900/chip_name.c
Change-Id: I2068e3859157b758ccea0ca91fa47d09a8639361
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1473
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
This patch aims to improve the microcode in CBFS handling that was
brought by the last patches from Stefan and the Chromium team.
Choices in Kconfig
- 1) Generate microcode from tree (default)
- 2) Include external microcode file
- 3) Do not put microcode in CBFS
The idea is to give the user full control over including non-free
blobs in the final ROM image.
MICROCODE_INCLUDE_PATH Kconfig variable is eliminated. Microcode
is handled by a special class, cpu_microcode, as such:
cpu_microcode-y += microcode_file.c
MICROCODE_IN_CBFS should, in the future, be eliminated. Right now it is
needed by intel microcode updating. Once all intel cpus are converted to
cbfs updating, this variable can go away.
These files are then compiled and assembled into a binary CBFS file.
The advantage of doing it this way versus the current method is that
1) The rule is CPU-agnostic
2) Gives user more control over if and how to include microcode blobs
3) The rules for building the microcode binary are kept in
src/cpu/Makefile.inc, and thus would not clobber the other makefiles,
which are already overloaded and very difficult to navigate.
Change-Id: I38d0c9851691aa112e93031860e94895857ebb76
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/1245
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
There are hyper-threading Atom CPUs, those would not enable L2
cache with model_6ex CAR code. Switch to code that can handle
different number of threads and cores.
Change-Id: I57328c231f8998f45f7b0d26c63b24585f8476dd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1384
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: James Laird <jhl@mafipulation.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The name is derived directly from the device path.
Change-Id: If2053d14f0e38a5ee0159b47a66d45ff3dff649a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1471
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
The CPU can arbitrarily reorder calls to rdtsc, significantly
reducing the precision of timing using the CPUs time stamp counter.
Unfortunately the method of synchronizing rdtsc is different
on AMD and Intel CPUs. There is a generic method, using the cpuid
instruction, but that uses up a lot of registers, and is very slow.
Hence, use the correct lfence/mfence instructions (for CPUs that
we know support it)
Change-Id: I17ecb48d283f38f23148c13159aceda704c64ea5
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1422
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Detection for a hyper-threading CPU was not compatible with multicore
CPUs. When using CPUID eax==4, also need to set ecx=0.
CAR init tested on real hardware with hyper-threading model_f25 and
under qemu 0.15.1 with multicore CPU.
Change-Id: I28ac8790f94652e4ba8ff88fe7812c812f967608
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1172
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
This reverts commit 042c1461fb777e583e5de48edf9326e47ee5595f.
It turned out that sending IPIs via broadcast doesn't work on
Sandybridge. We tried to come up with a solution, but didn't
found any so far. So revert the code for now until we have
a working solution.
Change-Id: I7dd1cba5a4c1e4b0af366b20e8263b1f6f4b9714
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1381
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This reverts commit 78efc4c36c68b51b3e73acdb721a12ec23ed0369.
The broadcast patch was reverted, so this commit should also
be reverted. The reason for reverting the broadcast patch:
It turned out that sending IPIs via broadcast doesn't work on
Sandybridge. We tried to come up with a solution, but didn't
found any so far. So revert the code for now until we have
a working solution.
Change-Id: I05c27dec55fa681f455215be56dcbc5f22808193
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1380
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The default TCC activation offset is 0, which means TCC
activation starts at Tj_max. For devices with limited
cooling ability it may be desired to lower TCC activation.
This adds an option that can be declared in the devicetree
to set the TCC activation to a non-zero value.
Enable tcc_offset=15 in devicetree.cb and build/boot
the BIOS and check that the value is set in the MSR:
> and $(shr $(rdmsr 0 0x1a2) 24) 0xf
0xf
Change-Id: I88f6857b40fd354f70fa9d5d9c1d8ceaea6dfcd1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1343
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Split this behavior out from PNOT() so the OS can
update _PPC limit without re-reading C-state tables.
Change-Id: I81b9111a4866f6b9916f74ac57a3caefaa77c565
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1342
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The existing NVS variable for PPCM will be used to
select a dynamic max P-state.
By itself this does not change existing behavior because
the NVS PPCM variable is initialized to zero.
PPCM can be tested by building and booting a modified BIOS
that sets gnvs->ppcm to a value greater than 1 and checking
from the OS that the P-state is limited to that value.
Change-Id: Ia7b3bbc6b84c1aa42349bb236abee5cc92486561
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1341
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On SandyBridge systems configured to work with Panther Point the CPU
would wrongly be described as IvyBridge. Fix this issue and drop an
unneeded Kconfig variable at the same time.
Change-Id: I501a4fa00613e589cd315cfee61b2f9561dfcb4d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1335
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Idee4facc18e0be60906d2a2f0e99bd39de8d7247
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1332
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On both SandyBridge and IvyBridge BCLK is fixed at 100MHz. Have the
comment reflect that.
Change-Id: Ia81c3501dc3e68cf3143c3bc864dfbf88901f9f9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1336
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
.. in case the system has pluggable CPUs or might come in different SKUs.
Change-Id: I7a7cd95b4de5dd78370355f448688e8d000434c1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1333
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Date and time are mixed up:
microcode: updated to revision 0x12 date=2012-12-04
should be
microcode: updated to revision 0x12 date=2012-04-12
Change-Id: I85f9100f31d88bb831bef07131f361c92c7ef34e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1334
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
CPUs with configurable TDP will run the TSC at the max non-turbo
ratio for the maximum TDP value, which can cause issues if another
TDP is desired. To deal with this we set the flex ratio to the
nominal TDP ratio early in the boot and then configure the Soft
Reset Data registers so the PCH can tell the CPU what frequency
to run at after a reset.
This is done very early in the bootblock because it is necessary
to reset the system after setting a flex ratio.
The end result is that the TSC will now increment at the max
non-turbo frequency for the nominal TDP.
On some system with 1.8GHz CPU ensure that the kernel
detects the CPU speed as ~1800mhz rather than ~2300mhz:
> dmesg | grep "MHz processor"
[ 0.004000] Detected 1795.801 MHz processor.
Change-Id: I8436dced9199003b6423186a2b041e3f7b84ab8c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1329
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The BWG says ivybridge current limit for PP1 is 50A.
Verify the PP1 current limit value on link device:
> echo $(( ( $(rdmsr 0 0x602) & 0x1fff ) >> 3 ))
50
Change-Id: I946269d21ef605f2525fe03993f569d69128294b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1305
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Ivybridge B0+ CPUs are capable of supporting multiple TDP levels.
This complicates the default case because now the registers that
were reporting max non-turbo ratio are reporting that value for
the highest possible TDP level.
For now this change just forces everything to use the Nominal TDP
values instead of the higher (or lower) levels.
- When building P-state tables, determine the P[1] (max non turbo)
ratio based on the Nominal ratio if available.
- Set the turbo activation ratio to the Nominal max ratio.
- Mirror the power level settings in new MCHBAR register after
they are written, which happens after BIOS_RESET_CPL is set.
- Set the current ratio to Nominal ratio at boot.
1) Verify that P-state table is generated properly with
P[0]=1801MHz (ratio 0x1C) and P[1]=1800MHz (ratio 0x12)
PSS: 1801MHz power 17000 control 0x1c00 status 0x1c00
PSS: 1800MHz power 17000 control 0x1200 status 0x1200
2) Verify power limits in MCHBAR match PKG_POWER_LIMIT:
> rdmsr 0 0x610
0x800080aa00dc8088
> mmio_read32 0xfed159a4
0x000080aa
> mmio_read32 0xfed159a0
0x00dc8088
3) Verify turbo activation ratio is set to nominal ratio:
> rdmsr 0 0x64c
0x0000000000000012
4) Check that proper ratio was set at boot on one core only:
> grep 'frequency set to' /sys/firmware/log
model_x06ax: frequency set to 1800
model_x06ax: frequency set to 1800
model_x06ax: frequency set to 1800
model_x06ax: frequency set to 1800
Change-Id: I592e60a7740f31b140986a8269dca91b4adbb270
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1304
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Nothing is yet enabled, this is just a config skeleton change.
The MICROCODE_INCLUDE_PATH definition is going to be used by the
Makefile building the microcode blob for CBFS inclusion.
Change-Id: I7868db3cfd4b181500e361706e5f4dc08ca1c87d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1292
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
When microcode storage in CBFS is enabled, the make system is supposed
to generate the microcode blob and place it into the generated ROM
image as a CBFS component.
The microcode source representation does not change: it is still an
array of 32 bit constants. This new addition compiles the array into a
separate object file and then strips all sections but data.
The raw data section is then included into CBFS as a file named
'microcode_blob.bin' of type 0x53, which is assigned to microcode
storage.
Change-Id: I84ae040be52f520b106e3471c7e391e64d7847d9
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1295
Tested-by: build bot (Jenkins)
|
|
When CONFIG_MICROCODE_IN_CBFS is enabled, find the microcode blob in
CBFS and pass it to intel_update_microcode() instead of using the
compiled in array.
CBFS accesses in pre-RAM and 'normal' environments are provided
through different API.
Change-Id: I35c1480edf87e550a7b88c4aadf079cf3ff86b5d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1296
Tested-by: build bot (Jenkins)
|
|
In preparation to support CBFS hosted microcode blobs, this change
renames the wrapper include file containing the microcode to be
independent of CPU model.
Change-Id: If1a4963a52e5037a3a3495b90708ffc08b23f4c1
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1294
Tested-by: build bot (Jenkins)
|
|
Dump and disassemble ACPI tables and look in _CST.
In the last entry the state was getting set to 0:
Package (0x04)
{
ResourceTemplate ()
{
Register (FFixedHW,
0x01, // Bit Width
0x02, // Bit Offset
0x0000000000000030, // Address
0x01, // Access Size
)
},
0x00000000, // State
0x0000005A, // Latency
0x000000C8 // Power
}
Now it is properly identifed as state 3:
Package (0x04)
{
ResourceTemplate ()
{
Register (FFixedHW,
0x01, // Bit Width
0x02, // Bit Offset
0x0000000000000030, // Address
0x01, // Access Size
)
},
0x00000003, // State
0x0000005A, // Latency
0x000000C8 // Power
}
Change-Id: Ie0a68606c5a43ac5fb5ba7bb9a3fef933ad67b64
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1297
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
There are several reasons for this:
1. It's a core setting, not a platform setting, which is bizarre. But,
we disable vmx via an SMI, and that only happens on core 0.
Hence, the code did not correctly make the same settings on all cores-
one had them disabled, the others were in an unknown state.
When (e.g.) kvm started on a vmx-enabled core, then moved to a
vmx-disabled core, the processor would reset *very* quickly.
Changing this would be messy.
2. On the CPU on link, there is something about trying to set the lock
bit that is getting a GPF.
3. It's the wrong place and time to set it. Once controlled, they can't
be changed in the kernel. The kernel is what should control this
feature, not the BIOS, as we have learned time and time again. If
somebody is in as root and can start a VM, you have a lot more to
worry about than someone starting a guest virtual machine.
Change-Id: I4f36093f1b68207251584066ccb9a6bcfeec767e
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/1276
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
CACHE_ROM_SIZE default is ROM_SIZE, the Flash device size set
in menuconfig. This fixes a case where 8 MB SPI flash MTRR setup
would not cover the bottom 4 MB when ramstage is decompressed.
Verify CACHE_ROM_SIZE is power of two.
One may set CACHE_ROM_SIZE==0 to disable this cache.
Change-Id: Ib2b4ea528a092b96ff954894e60406d64f250783
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1146
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
|
|
Diff between model_106cx and model_6ex CAR codes suggests currently
used model_106cx CAR is not optimal - destination RAM and source ROM
of ramstage copy_and_run are only partly set cacheable.
It appears variable MTRR setting for XIP cache is left enabled on
model_106cx code, where it should have extended to cover all of Flash.
Introduces untested functional change on boards:
intel/d945gclf
iwave/iWRainbowG6
Deletes file:
model_106cx/cache_as_ram.inc
Change-Id: I35229f8433927e83821e72e9d9a9fc8fb09c3f1d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/642
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
|
|
A diff from model_6fx to model_106cx suggests there is little
CORE2 specific code that was once considered useful to have.
In its current status however, sockets supporting model_6fx use
model_6ex CAR init, so that specific code is actually
never used.
Deletes file:
model_6fx/cache_as_ram.inc
Change-Id: I6c0204446fa98207e31f91895e1cf30fde42382c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/640
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
|
|
Default CPU_ADDR_BITS is 36.
For Atom (model_106cx) use 32. This model is known to
fail execution-in-place (XIP) with the default 36.
Pentium M should use 32, but doesn't even with this patch.
Some Xeon and CORE(2) models should use 38 or 40.
Change-Id: If604badcdc578c4f4bc7d30da2f61397ec0d754c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/639
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
|
|
The new broadcast code doesn't support serial init - if a CPU
needs serial init, this should be handled in the model specific CPU
init code.
Change-Id: I7cafb0af10d712366819ad0849f9b93558e9d46a
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1140
Tested-by: build bot (Jenkins)
|
|
The current code for initializing AP cpus has several shortcomings:
- it assumes APIC IDs are sequential
- it uses only the BSP for determining the AP count, which is bad if
there's more than one physical CPU, and CPUs are of different type
Note that the new code call cpu->ops->init() in parallel, and therefore
some CPU code needs to be changed to address that. One example are old
Intel HT enabled CPUs which can't do microcode update in parallel.
Change-Id: Ic48a1ebab6a7c52aa76765f497268af09fa38c25
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1139
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Early HT-enabled CPUs do not serialize microcode updates within a core.
Solve this by running microcode updates on the thread with the smallest
lapic ID of a core only.
Also set MTRRs once per core only.
Change-Id: I6a3cc9ecec2d8e0caed29605a9b19ec35a817620
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1142
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Those CPUs support the PECI (Platform Environment Control
Interface), so enable it. This interface is commonly used
for tasks like fan control.
Change-Id: Id2dadc4821de8cc0b579e77235aa36892e57fd02
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1104
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
It's only used in the ACPI generator for Sandybridge/Ivybridge CPUs
and the code can easily be changed to not rely on any Kconfig magic.
Change-Id: Ie2f92edfe8908f7eb2fda3088f77ad22f491ddcf
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1047
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Replace #if CONFIG_FOO==1 with #if CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*1[[:space:]]*\$,#if \1," {} +
Replace #if (CONFIG_FOO==1) with #if CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*1)[[:space:]]*\$,#if \1," {} +
Replace #if CONFIG_FOO==0 with #if !CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*0[[:space:]]*\$,#if \!\1," {} +
Replace #if (CONFIG_FOO==0) with #if !CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*0)[[:space:]]*\$,#if \!\1," {} +
(and some manual changes to fix false positives)
Change-Id: Iac6ca7605a5f99885258cf1a9a2473a92de27c42
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1004
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
Another bug in the Intel microcode update code that existed since we switched
to LinuxBIOSv2 in 2004:
The inline assembly code that reads the CPU revision from an MSR after running
cpuid(1) trashes registers EBX and ECX. Only ECX was mentioned in the clobber
list. C code running after this function could silently access completely wrong
data, which resulted in the wrong date being printed on microcode updates (and
potentially other issues happening until the C code writes to EBX again)
Change-Id: Ida733fa1747565ec9824d3a37d08b1a73cd8355f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/996
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
If microcode.c is built by romcc, this indicates that we are running
microcode updates in the bootblock (e.g. before enabling cache as ram).
In this case we did not enable any consoles yet, so we don't output
anything.
This patch removes inclusion of the unnecessary console/console.h for
that case, which was breaking with certain configurations.
Change-Id: Iebb57794d7b1e84cac253d249d47b88de4dd28a3
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/988
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This code fixes the sandybridge C state generation code to work with
the current version of the ACPI code generator.
Change-Id: I56ae1185dc0694c06976236523fdcbe5c1795b01
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/950
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
... in order to unify the Sandybridge and Lenovo implementations
currently used in the tree.
- use acpi_addr_t in acpigen_write_register()
- use acpi_cstate_t for cstate tables (and fix up
the x60 and t60)
- drop cst_entry from acpigen.h
Change-Id: Icb87418d44d355f607c4a67300107b40f40b3b3f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/943
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Most subsystems print their name with a colon, and then the
message. Do the same thing for the microcode update code.
Also, each microcode update has a date header. Print the
date from that header to make it easier to determine whether
you're running the latest microcode.
Change-Id: Ic22947c4b9f0502d4091d975e1f1ab42f70aa1aa
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/929
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
- add GPLv2 + copyright header after talking to Ron
- "bits" in struct microcode served no real purpose but
getting its address taken. Hence drop it
- use asm volatile instead of __asm__ volatile
- drop superfluous wrmsr (that seems to be harmless but
is still wrong) in read_microcode_rev
- use u32 instead of unsigned int where appropriate
- make code usable both in bootblock and in ramstage
- drop ROMCC style print_debug statements
- drop microcode update copy in Sandybridge bootblock
Change-Id: Iec4d5c7bfac210194caf577e8d72446e6dfb4b86
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/928
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Instead of opaque numbers like (1<<29), use
symbols like CR0_NoWriteThrough.
Change-Id: Id845e087fb472cfaf5f71beaf37fbf0d407880b5
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/833
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Fix regression after commit:
7dfe32c5408916b6cb23f1ec48e473e1c728d300
Only align 16-bit entry on platforms that really require it,
indicated by selecting SIPI_VECTOR_IN_ROM in CPU Kconfig.
Disable assertion test of AP_SIPI_VECTOR for platforms not
depending on this feature.
Build of romstage should be fixed to get the vector address from
bootblock build automatically.
Change-Id: Ide470833c0254df1a9ff708369ab1c095ccfb98d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/875
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I9f37e291c00c0640c6600d8fdd6dcc13c3e5b8d5
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/855
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
From wikipedia:
Intel Turbo Boost is a technology implemented by Intel in certain
versions of their Nehalem- and Sandy Bridge-based CPUs, including Core
i5 and Core i7 that enables the processor to run above its base
operating frequency via dynamic control of the CPU's "clock rate".
It is activated when the operating system requests the highest
performance state of the processor.
Change-Id: I166ead7c219083006c2b05859eb18749c6fbe832
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/844
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The socket mPGA604 is for P4 Xeon which to my knowledge is always
HT-enabled. I assume the existing usage of car/cache_as_ram.inc
on socket_mPGA604, namely the Tyan S2735, as broken.
Existing car/cache_as_ram.inc has invalid SIPI vector and it does
not initialise AP CPU's to activate L2 cache.
Other mPGA604 boards are not affected, as they have not been
converted to CAR.
Change-Id: I7320589695c7f6a695b313a8d0b01b6b1cafbb04
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/607
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I441326ecbda72ec7e99fc99bf40a81aa7e94ee26
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/834
Tested-by: build bot (Jenkins)
Reviewed-by: Mathias Krause <minipli@googlemail.com>
|
|
Use CPUID to get MAXPHYADDR and set MTRR masks correctly.
Also only BSP CPU clears MTRRs and initializes its Local APIC.
Change-Id: I89ee765a17ec7c041284ed402f21d9a969d699bd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/686
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This improvement of CAR code starts the sibling CPU processors and
clears their cache disable bits (CR0.CD) in case a hyper-threading
CPU is detected.
Change-Id: Ieabb86a7c47afb3e178cc75bb89dee3efe0c3d18
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/604
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Most or many Xeons have no MSR 0x11e.
I have previously tested that a HT-enabled P4 (model f25) can
execute this but will not have cache-as-ram enabled. Should work
for non-HT P4.
Change-Id: I28cbfa68858df45a69aa0d5b050cd829d070ad66
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/644
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Delete dead CAR code and whitespace fixes.
Replace cryptic 32bit hex values with existing LAPIC definitions.
Do not assume state of direction flag before "rep" instruction.
Do not load immediate values on temporary registers when not needed.
Parameter pushed on stack was not popped (or flushed) after returning
from call. This is a sort-of memory leak if multiple call's are
implemented the same way.
Change-Id: Ibb93e889b3a0af87b89345c462e331881e78686a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/643
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Cache was enabled for the last 4 MB below 4 GB when ramstage is
loaded. This does not cover the case of a 8 MB Flash and could
overlap with some system device placed at high memory.
Use the actual device size for the cache region. Mainboard
may override this with Kconfig CACHE_ROM_SIZE if necessary.
Change-Id: I622223b1e2af0b3c1831f3570b74eacfde7189dc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/641
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Copy model_6ex CAR as car/cache_as_ram_ht.inc to be extended
with hyper-threading CPU support.
Change-Id: I09619363e714b1ebf813932b0b22123c1d89010e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/606
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Only the BSP CPU was able to start its hyper-threading CPU siblings.
When an AP CPU attempts this it calls start_cpu() within start_cpu(),
deadlocking the system with start_cpu_lock.
At the time intel_sibling_init() is run, the BSP CPU is still
walking the cpu_bus linked list in lapic_cpu_init: start_other_cpus().
A sibling CPU appended at the end of this list will get started.
Also fail compile with #error if SERIAL_CPU_INIT==0, as microcode
updates on hyper-threading sibling CPUs must be serialized.
Tested with HT-enabled P4 Xeons on dual-socket604 platform.
Change-Id: I0053f58f49ed604605ce0a55e826d3e1afdc90b6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/775
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
It was not obvious which CAR was compiled in. Also build would fail
if a socket included two models with both having an include for CAR.
Change-Id: I000c2e24807c3d99347a43d120333c13fbf91af4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/626
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Unifies models 6ex, 6fx and 106cx.
Change-Id: I2bb632c7148a7d937f24eb559f7f4e539d227470
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/638
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I6ea5ca631c22fe870224a498b68d77d85798b3f4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/637
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Kconfig directives to select chip drivers for compile literally
match the chip directory names capitalized and underscored.
Note: CPU_INTEL_CORE2 was used on both model_6fx and model_1067x.
Change-Id: I8fa5ba71b14dcce79ab2a2c1c69b3bc36edbdea0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/618
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Iee7d3ff2884d8c43ff1af498160589e551bc9cc8
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/492
Tested-by: build bot (Jenkins)
|
|
The current code uses static values for the physical address size
supported by a CPU. This isn't always the right value: I.e. on
model_6[ef]x Core (2) Duo CPUs physical address size is 36, while
Xeons from the same family have 38 bits, which results in invalid
MTRR setup. Fix this by getting the right number from CPUID.
Change-Id: If019c3d9147c3b86357f0ef0d9fda94d49d811ca
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/529
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This function prevents the linker from choosing the right
get_cst_entries(), preventing writing the _CST tables.
Change-Id: I4bc0168aee110171faeaa081f217dfd1536bb821
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/496
Tested-by: build bot (Jenkins)
|
|
The base is now calculated automatically, and all mentions of that
config option were typical anyway (4GB - XIP_ROM_SIZE).
Change-Id: Icdf908dc043719f3810f7b5b85ad9938f362ea40
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/366
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
It is meant to be a address and not a dereference. Otherwise MTRR
is filled with code and not with the address.
This is what I hate at most on the AT&T syntax. Instead of taking
the address, it was a dereference. Not greatly visible, except
I wondered why opcode is not 0xb4 but 0xa1 and it took another
half an our to see it.
Change-Id: I6b339656024de8f6e6b3cde63b16b7ff5562d055
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/358
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
This change removes CONFIG_TINY_BOOTBLOCK, CONFIG_BIG_BOOTBLOCK, and
all their uses, assuming TINY_BOOTBLOCK=y, BIG_BOOTBLOCK=n.
This might break a couple of boards on runtime, but so far, fixes were
quite simple.
There's a flag day: Code that relies on CONFIG_TINY_BOOTBLOCK must be
adapted.
Change-Id: I1e17a4a1b9c9adb8b43ca4db8aed5a6d44d645f5
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/320
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
That value is now generated from a code address and CONFIG_XIP_ROM_SIZE.
This works as MTRRs are fully specified by their size and any address
within the range.
Change-Id: Id35d34eaf3be37f59cd2a968e3327d333ba71a34
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/348
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Idb4b57044808918de343d31519768d0986840f01
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/321
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
As new microcode files were included, the table was not updated with
families 0f25 and 0f26.
Change-Id: I5bb8be9d7c37eb8406dcb48a4b933eab24639bda
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/290
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The CPUs start on their slowest speed, and were left that way by
coreboot. This change will speed up coreboot a bit, as well as
systems that don't change the clock for whatever reason.
Change-Id: Ia6225eea97299a473cf50eccc6c5e7de830b1ddc
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/176
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|