| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds ANSI escape sequences to highlight a log line based on
its loglevel to the output of "interactive" consoles that are meant to
be displayed on a terminal (e.g. UART). This should help make errors and
warnings stand out better among the usual spew of debug messages. For
users whose terminal or use case doesn't support these sequences for
some reason (or who simply don't like them), they can be disabled with a
Kconfig.
While ANSI escape sequences can be used to add color, minicom (the
presumably most common terminal emulator for UART endpoints?) doesn't
support color output unless explicitly enabled (via -c command line
flag), and other terminal emulators may have similar restrictions, so in
an effort to make this as widely useful by default as possible I have
chosen not to use color codes and implement this highlighting via
bolding, underlining and inverting alone (which seem to go through in
all cases). If desired, support for separate color highlighting could be
added via Kconfig later.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I868f4026918bc0e967c32e14bcf3ac05816415e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Chromebooks normally run with non-serial enabled firmware because
writing to the UART console is very slow. This unfortunately makes
debugging boot errors more difficult. We tend to rely on port 80s and/or
the vboot recovery code.
When CONSOLE_CBMEM_DUMP_TO_UART is selected it will dump the entire
cbmem console to the UART whenever `vboot_reboot()` is called. We don't
incur any boot time penalty in the happy path, but still retain the
ability to access the logs when an error occurs.
The previous implementation was using a hard coded UART index and
`get_uart_baudrate` was always returning 0 since `CONFIG_TTYS0_BAUD`
wasn't defined. This change makes it so the UART console properties are
available when CONSOLE_CBMEM_DUMP_TO_UART is set. This results in the
following .config diff:
+CONFIG_UART_FOR_CONSOLE=0
+CONFIG_TTYS0_BASE=0x3f8
+CONFIG_TTYS0_LCS=3
+CONFIG_CONSOLE_SERIAL_115200=y
+CONFIG_TTYS0_BAUD=115200
This functionality is especially helpful on Guybrush. PSP Verstage is
run on S0i3 resume. Today, if there is an error, the cbmem console is
lost since it lives in the PSP SRAM.
BUG=b:213828947, b:215599230
TEST=Build non-serial guybrush FW and verify no serial output happens in
happy path. Inject a vboot error and perform an S0i3 suspend/resume.
Verify CBMEM console gets dumped to the correct UART.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I997942204603362e51876a9ae25e493fe527437b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Pre-bootblock stages (i.e., VBOOT_STARTS_BEFORE_BOOTBLOCK) might not
have the ability to log to the UART, so their console messages are
inaccessible until the boot processes gets into the payload or OS.
This makes it difficult to debug verstage.
This feature will dump the pre-bootblock CBMEM console immediately
after the bootblock console is initialized. I chose to do this in
console_init instead of bootblock_soc_init because I wanted to have the
pre-bootblock contents dumped before the coreboot bootblock starting
message is printed.
BUG=b:213828947
TEST=Boot guybrush with PSP verstage and verify verstage logs are dumped
to the UART.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I363c93ef3ee6c5c303a6a68f88a622e2aa62594c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61012
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These issues were found and fixed by codespell, a useful tool for
finding spelling errors.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I5b8ecdfe75d99028fee820a2034466a8ad1c5e63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58080
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Expand NO_EARLY_BOOTBLOCK_POSTCODES to all of the early assembly code in
bootblock.
BUG=b:191370340
TEST: Build with & without the option enabled
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Idb4a96820d5c391fc17a0f0dcccd519d4881b78c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add a new CONFIG_OVERRIDE_UART_FOR_CONSOLE token to override the index
of uart port, platform use a get_uart_for_console routine to decide what
index value should be used for console.
Signed-off-by: Bryant Ou <Bryant.Ou.Q@gmail.com>
Change-Id: I2079bd1e5ffa209553383b6aafe3b8724849ba2a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
To avoid confusion with `flashconsole` (CONSOLE_SPI_FLASH), prefix this
option with `EM100Pro`. Looks like it is not build-tested, however.
Change-Id: I4868fa52250fbbf43e328dfd12e0e48fc58c4234
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
This adds support for line-buffered console output to System76 EC firmware.
Once the print command is received, the EC firmware multiplexes the output
to any enabled console on the EC. This can be a memory ringbuffer, a
parallel port (using the keyboard connector), or i2c (using the battery
connector). Once the entire buffer is sent, it sets the command register
to 0, indicating completion. For more information, please see:
https://github.com/system76/ec/blob/master/doc/debugging.md
Tested on system76/lemp9 with CONSOLE_SYSTEM76_EC enabled.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I861bf3e22f40dd6c3ec7ba1d73711b399358e332
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Change-Id: I379a5664776624600ff1c2919bffa77c877d87ab
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
It is equivalent to the CPU_QEMU_X86 symbol.
Change-Id: Ic16233e3d80bab62cc97fd075bdcca1780a6a2b5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ia0405fdd448cb31b3c6ca3b3d76e49e9f430bf74
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Because the function is implemented in C, post_code() calls
from cache_as_ram.S and other early assembly entry files may
not currently work for cold boots. Assembly implementation
needs to follow one day.
This effectively removes PORT80 routing from boards with
ROMCC_BOOTBLOCK.
Change-Id: I71aa94b33bd6f65e243724810472a440e98e0750
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
The romcc bootblock will be deprecated soon and most platforms use
C_ENVIRONMENT_BOOTBLOCK already. This patch drops the
CONFIG_C_ENVIRONMENT_BOOTBLOCK symbol and adds CONFIG_ROMCC_BOOTBLOCK
where needed.
Change-Id: I773a76aade623303b7cd95ebe9b0411e5a7ecbaf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37154
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Kconfig became stricter on what it accepts, so accomodate before
updating to a new release.
Change-Id: I92a9e9bf0d557a7532ba533cd7776c48f2488f91
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This has nothing to do with console options.
This also improves the help text to reflect what it actually does.
Change-Id: I039f4f6bbe144769d6a362192b225838ed3d9d43
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Almost all platforms force it on. Make it enabled by
default but under user control to optionally disable it.
Change-Id: I6b0f19c8bfd6ffed93023d57a1d28ca6acc06835
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
It doesn't make sense to print these values for memory-mapped UARTs.
Change-Id: Ie2d9cf95f0b0fdcf601e74de799b1390c08f2335
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add a new Kconfig NO_BOOTBLOCK_CONSOLE to disable the BOOTBLOCK_CONSOLE
option completely. The commit message of fbb11cf (ARM: Separate the
early console (romstage) from the bootblock console.) states that it
doesn't work before romstage on Exynos 5420.
Change-Id: I9b56a52f2555b5233300f27031a9ef50e7ab7cea
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Invert the default instead of selecting it everywhere. Restores the
ability to use its Kconfig prompt.
Beside Qemu targets, the only platforms that didn't select it seem
to be samsung/exynos5420, intel/cannonlake, and intel/icelake. The
latter two were about to be patched anyway.
Change-Id: I7c5b671b7dddb5c6535c97c2cbb5f5053909dc64
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30891
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Kconfig declaration for FIXED_UART_FOR_CONSOLE was accidentally
placed inside an `if CONSOLE_SERIAL` in a96e66a (soc/intel: Clean mess
around UART_DEBUG).
TEST=Start a clean config, select intel/leafhill and disable serial
console. Confirm that config can be saved without error.
Change-Id: Ie41687e91af11a13697cbe25938dada2c74b40fb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Everything is wrong here, the Kconfig symbols are only the tip of the
iceberg. Based on Kconfig prompts the SoC code performed pad configu-
rations! I don't see why the person who configures coreboot should have
the board schematics at hand.
As a mitigation, we remove the prompts for UART_DEBUG, which is renamed
to INTEL_LPSS_UART_FOR_CONSOLE (because the former didn't really say
what it's about), and for UART_FOR_CONSOLE in case the former is selec-
ted.
Change-Id: Ibe2ed3cab0bb04bb23989c22da45299f088c758b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The dependencies of CONSOLE_SERIAL and DRIVERS_UART were somehow
backwards. Fix that. Now, CONSOLE_SERIAL depends on DRIVERS_UART,
because it's using its interface. The individual UART drivers
select DRIVERS_UART, because they implement the interface and
depend on the common UART code.
Some guards had to be fixed (using CONSOLE_SERIAL now instead of
DRIVERS_UART). Some other guards that were only about compilation
of units were removed. We want to build test as much as possible,
right?
Change-Id: I0ea73a8909f07202b23c88db93df74cf9dc8abf9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
CB:26053 changed coreboot's default loglevel from SPEW to DEBUG. This
may be the most reasonable choice for most users that are mostly
interested in the UART console. However, on Chrome OS devices the UART
is disabled for production configurations anyway, and instead they rely
heavily on the CBMEM console for remote debugging and bug reports. For
these kinds of cases more info is almost always better, and you can't
easily reproduce a remotely filed bug if you notice that you need some
info that is only provided by BIOS_SPEW. On the other hand, the cost of
logging extra info to the CBMEM console is pretty negligible.
Therefore, let's bump the loglevel for CONFIG_CHROMEOS in particular
back up to the maximum. (Unfortunately, it seems that you can't 'select'
a choice option from another option, so this has to go in the
console/Kconfig file.)
Change-Id: I50724e3f7f8f57fdbc5846f21babc71798b21b65
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/29144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
It seems to be the only user of the USB debug driver. So having to
enable it separately seems wrong.
It still depends on the selection of the EHCI debug driver.
Change-Id: I5f5f38a912423d9b8f1e71ae875b6a14fdee651c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The former default SPEW is very noisy, intentionally. It is usually
only useful to debug specific issues and doesn't carry much infor-
mational value.
Reducing the loglevel should also mitigate overflows in pre-CBMEM
console buffers.
Change-Id: Iebcd4681572c58f1d17085c5ef01a2dd49e981ca
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/26053
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Angel Pons
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds a config option to allow mainboard to override
the console loglevel. When the option is set, the platform has
to define the function get_console_loglevel returning a valid
loglevel value.
This allows a mainboard to sample a GPIO to switch the loglevel
value between different environments (qualification vs production)
without re-flashing.
Change-Id: Id6cc72b8fe5c4c50a6f83ce80e6440b078eec6e2
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The rationale is to allow the mainboard to override the default
baudrate for instance by sampling GPIOs at boot.
A new configuration option is available for mainboards to select
this behaviour. It will then have to define the function
get_uart_baudrate to return the computed baudrate.
Change-Id: I970ee788bf90b9e1a8c6ccdc5eee8029d9af0ecc
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
If CONSOLE_SPI_FLASH config is enabled, we write the cbmem
messages to the 'CONSOLE' area in FMAP which allows us to grab the
log when we read the flash.
This is useful when you don't have usb debugging, and
UART lines are hard to find. Since a failure to boot would
require a hardware flasher anyways, we can get the log
at the same time.
This feature should only be used when no alternative is
found and only when we can't boot the system, because
excessive writes to the flash is not recommended.
This has been tested on purism/librem13 v2 and librem 15 v3 which
run Intel Skylake hardware. It has not been tested on other archs
or with a driver other than the fast_spi.
Change-Id: I74a297b94f6881d8c27cbe5168f161d8331c3df3
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
It's hidden behind a configuration option `CONFIG_RAMSTAGE_LIBHWBASE`.
This also adds some glue code to use the coreboot console for debug
output and our monotonic timer framework as timer backend.
v2: Also update 3rdparty/libhwbase to the latest master commit.
Change-Id: I8e8d50271b46aac1141f95ab55ad323ac0889a8d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/16951
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This reverts commit 2c8f3bd91b54e85b4d2e24894ee8bbbfb9ad8a31.
I mistakenly commited a WIP, sorry.
Change-Id: I3c66c688dbfd903ecf5303abcdf6b5ded84585c7
Reviewed-on: https://review.coreboot.org/17028
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
On other architectures, the serial ports aren't mapped at 0x3f8.
WIP: I'm not sure how exactly the dependency should be encoded in
Kconfig.
Change-Id: Ia1de545325a53607f62d08e76b2f61b25edbe6ef
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16982
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Kconfig hex values don't need to be in quotes, and should start with
'0x'. If the default value isn't set this way, Kconfig will add the
0x to the start, and the entry can be added unnecessarily to the
defconfig since it's "different" than what was set by the default.
A check for this has been added to the Kconfig lint tool.
Change-Id: I86f37340682771700011b6285e4b4af41b7e9968
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16834
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add a Kconfig value to enable the console during postcar. Add a call
to console_init at the beginning of the postcar stage in exit_car.S.
TEST=Build and run on Galileo Gen2
Change-Id: I66e2ec83344129ede2c7d6e5627c8062e28f50ad
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16001
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Those options have no effect or lead to compile error on ARM due
to fundamental incompatibilities. Add proper "depends on" clauses
to hide them.
Change-Id: I860fbd331439c25efd8aa92023195fda3add2e2c
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13904
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable baud rates of 230400, 460800 and 921600. Leave the default set
to 115200.
TEST=Build and run on Galileo at 921600.
Change-Id: I8e3980f33665bc183b454cf97c68e297f1b0502c
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/13755
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add a "depends on SMP" to the value SQUELCH_EARLY_SMP Kconfig value to
disable its selection when SMP is not enabled.
TEST=Build for Galileo
Change-Id: Ia3aa1d2169ed793e1bb26538b74b12347453d5af
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/13639
Tested-by: build bot (Jenkins)
Reviewed-by: FEI WANG <wangfei.jimei@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Instead of depending BOOTBLOCK_CONSOLE on a set of architectures,
allow the arch or platform to specify whether it can provide a C
environment. This simplifies the selection logic.
Change-Id: Ia3e41796d9aea197cee0a073acce63761823c3aa
Signed-off-by: Alexandru Gagniuc <alexandrux.gagniuc@intel.com>
Reviewed-on: https://review.coreboot.org/12871
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I09943aafe29f6e7a2a878e7b6141661982dfc645
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12658
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add help and a comment about the serial IO port selection to give the
user better feedback when a port index is selected.
Change-Id: I4c1614be51aee0286308fbc5c24554e218120bf7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/12487
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The Intel cave creek chipset needs to have port 80 routing configured
before any post codes can be sent to port 80h. Sending post codes out
before the routing is done will hang the system.
This patch allows us to disable the first couple of post codes that go
out before the routing can be configured.
The Kconfig symbol is selected by the cave creek chipset (fsp_i89xx).
Change-Id: I9bf41669ec32744f87a1ed2de011d31c72ea38da
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/12422
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: York Yang <york.yang@intel.com>
|
|
The EM100Pro allows the debug console to be sent over the SPI bus.
This is not yet working in romstage due to the use of static variables
in the SPI driver code. It is also not working on chipsets that have
SPI write buffers of less than 10 characters due to the 9 byte
command/header length specified by the EM100 protocol.
While this currently works only with the EM100, it seems like it would
be useful on any logic analyzer with SPI debug - just filter on command
bytes of 0x11.
Change-Id: Icd42ccd96cab0a10a4e70f4b02ecf9de8169564b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The new function can be compiled in only when serial console is
disabled.
When invoked, this function initializes the serial interface and dumps
the contents of the CBMEM console buffer to serial output.
BRANCH=none
BUG=chromium:475347
TEST=compiled for different platforms with and without serial console
enabled. No actual test of this function yet.
Change-Id: Ia8d16649dc9d09798fa6970f2cfd893438e00dc5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a38a8254dd788ad188ba2509b9ae117d6f699579
Original-Change-Id: Ib85759a2727e31ba1ca21da7e6c346e434f83b52
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/265293
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9984
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The Kconfig options pertaining cbmem console in the preram
environment no longer make sense with the linker script
changes. Remove them and their usage within cbmem_console.
Change-Id: Ibf61645ca2331e4851e748e4e7aa5059e1192ed7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9851
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch creates a new mechanism to define the static memory layout
(primarily in SRAM) for a given board, superseding the brittle mass of
Kconfigs that we were using before. The core part is a memlayout.ld file
in the mainboard directory (although boards are expected to just include
the SoC default in most cases), which is the primary linker script for
all stages (though not rmodules for now). It uses preprocessor macros
from <memlayout.h> to form a different valid linker script for all
stages while looking like a declarative, boilerplate-free map of memory
addresses to the programmer. Linker asserts will automatically guarantee
that the defined regions cannot overlap. Stages are defined with a
maximum size that will be enforced by the linker. The file serves to
both define and document the memory layout, so that the documentation
cannot go missing or out of date.
The mechanism is implemented for all boards in the ARM, ARM64 and MIPS
architectures, and should be extended onto all systems using SRAM in the
future. The CAR/XIP environment on x86 has very different requirements
and the layout is generally not as static, so it will stay like it is
and be unaffected by this patch (save for aligning some symbol names for
consistency and sharing the new common ramstage linker script include).
BUG=None
TEST=Booted normally and in recovery mode, checked suspend/resume and
the CBMEM console on Falco, Blaze (both normal and vboot2), Pinky and
Pit. Compiled Ryu, Storm and Urara, manually compared the disassemblies
with ToT and looked for red flags.
Change-Id: Ifd2276417f2036cbe9c056f17e42f051bcd20e81
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f1e2028e7ebceeb2d71ff366150a37564595e614
Original-Change-Id: I005506add4e8fcdb74db6d5e6cb2d4cb1bd3cda5
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/213370
Reviewed-on: http://review.coreboot.org/9283
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
In addition to ARM based systems, allow MIPS based systems to select
bootblock console support.
BUG=chrome-os-partner:31438
TEST=none yet
Change-Id: I40e5d8b651102709118878a317f7e983a617f433
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1a41853273ef9ae716d5645379fcef79c5771b87
Original-Change-Id: I41f03ea8c8104ba2dd9f532b084696385d29636c
Original-Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/207973
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Commit-Queue: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/8769
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Currently on AMD boards no romstage messages can be saved in CBMEM, so
only messages from ramstage on will be stored in CBMEM. Other than
that nothing changes.
Enabling CBMEM console by default does not noticeably decrease boot
time as the messages are directly written to CAR or RAM.
The board status script under `util/board_status/` reads the coreboot
messages from CBMEM, which are then uploaded to the board status
repository. With CBMEM console disabled by default, currently no
coreboot console messages are uploaded to the board status repository,
although it is important to have those.
Enabling CBMEM console by default improves this situation, so that for
all boards at least ramstage messages are stored in the board status
repository.
Change-Id: I8d5a58c078325c43a0317bcfaafc722d039aab0b
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5350
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
|
|
This was added to handle cases of Intel FSP platforms that had
EARLY_CBMEM_INIT but could not migrate CAR variables to CBMEM.
These boards were recently fixed.
To support combination of EARLY_CBMEM_INIT without CAR migration was
added maintenance effort with little benefits. You had no CBMEM
console for romstage and the few timestamps you could store were
circulated via PCI scratchpads or CMOS nvram.
Change-Id: I5cffb7f2b14c45b67ee70cf48be4d7a4c9e5f761
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8636
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
If it's not supported on a particular board, either the build will fail or
checks within the cbmem console itself should detect the problem. There
shouldn't be random memory corruption any more.
BUG=None
TEST=Built with CONSOLE_CBMEM enabled on nyan and saw that it was actually
enabled.
BRANCH=None
Original-Change-Id: Id6c8c7675daafe07aa4878cfcf13faefe576e520
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/193167
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 20b486443bfc2d93d72bbc9e496023a00ab9ab30)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I39fbcdff61f6d8f520f2e9d7612dee78e97898b1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7748
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Use the value of CONSOLE_PRERAM_BUFFER_SIZE to determine if we can
do CBMEM console in bootblock and romstage. Kconfig forces it to zero
if _BASE is unset or we cannot do CAR migration on x86.
Add CBMEM console to bootblock, except for x86. Only one of bootblock
and romstage clears the pre-RAM buffer.
To start with empty console log on S3 wakeup, ramstage now clears
previous contents of CBMEM buffer if there was no pre-RAM buffer.
Unify Kconfig variable naming.
TODO: ARM configurations do not define PRERAM_BUFFER_BASE values.
Change-Id: I70d82da629529dbfd7bc9491223abd703cbc0115
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7862
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Works in the RISCV version of QEMU.
Note that the lzmadecode is so unclean that it needs a lot of work.
A cleanup is in progress.
We decided in Prague to do this as one thing, because it forms a nice case study
of the bare minimum you need to add to get a new architecture going in qemu.
Change-Id: If5af15c3a70733d219973e0d032746f8ab027e4d
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/7584
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
On non-x86 systems, the location of the preram CBMEM console may not be in a
predictable place relative to other things in the linker script. That makes it
difficult to work with as its own section because the linker will complain if
you try to move backwards as it lays out memory. If the console header is
treated as an actual blob of memory which has to be put in the image, we'd
have to predict where to put it so that it isn't before something with a lower
address or after something with a higher address. Symbols, on the other hand,
can be defined arbitrarily.
Change-Id: I3257b981eee0c15bb997a9f2c55a03494c6ec6f0
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/193164
Reviewed-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit a492761c27076bcac080013d509ae4aafd6dc3e3)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/7013
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This is essentially a revert of commit 10bd772d. The CAR_MIGRATE
mechanism is only useful to migrate variables from a special region
(e.g. cache as RAM) into DRAM-backed CBMEM between different parts of
the romstage (it does not persist into ramstage). Since ARM devices use
SRAM for which there is no reason to become inaccessible in later parts
of the romstage, this mechanism isn't useful for them. Removing it makes
the romstage.ld script much simpler, which has the nice side-effect of
putting the BSS at the end of the memory image (so that cbfstool can
actually figure out that it doesn't need to be part of the ROM image).
Old-Change-Id: I50e91d8bd51b5deb19446d9da48699edecbef6ea
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176761
Reviewed-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit ebfd698e57c902e2f39a0cfc1bc2b02665e47ec6)
console: Make cbmem depend on x86.
The cbmem implementation isn't supported on anything other than x86 right now
and actually causes memory corruption on ARM machines. Until that's fixed, this
will prevent people from turning it on and causing hard to track down errors.
Old-Change-Id: I00e8aacf008acfe2f76d4eab82570f7c1cc89cab
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/191107
Reviewed-by: Julius Werner <jwerner@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit e54f16e346a7f2c66d802fb78a6b24e53b732b83)
Squashed two related commits for cbmem support on arm.
Change-Id: I2be48cea348ee5dc8ca3632d743500aa111bab08
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6888
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
|
|
board_status shows that truncation of few KiB is pretty common.
So bump this value.
Change-Id: I78a16974846a59ee4eae782380e6d01d2fa324f2
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6902
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
There are ARM systems which are essentially heterogeneous multicores where
some cores implement a different ARM architecture version than other cores. A
specific example is the tegra124 which boots on an ARMv4 coprocessor while
most code, including most of the firmware, runs on the main ARMv7 core. To
support SOCs like this, the plan is to generalize the ARM architecture so that
all versions are available, and an SOC/CPU can then select what architecture
variant should be used for each component of the firmware; bootblock,
romstage, and ramstage.
Old-Change-Id: I22e048c3bc72bd56371e14200942e436c1e312c2
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/171338
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 8423a41529da0ff67fb9873be1e2beb30b09ae2d)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
ARM: Split out ARMv7 code and make it possible to have other arch versions.
We don't always want to use ARMv7 code when building for ARM, so we should
separate out the ARMv7 code so it can be excluded, and also make it possible
to include code for some other version of the architecture instead, all per
build component for cases where we need more than one architecture version
at a time.
The tegra124 bootblock will ultimately need to be ARMv4, but until we have
some ARMv4 code to switch over to we can leave it set to ARMv7.
Old-Change-Id: Ia982c91057fac9c252397b7c866224f103761cc7
Reviewed-on: https://chromium-review.googlesource.com/171400
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 799514e6060aa97acdcf081b5c48f965be134483)
Squashed two related patches for splitting ARM support into general
ARM support and ARMv7 specific pieces.
Change-Id: Ic6511507953a2223c87c55f90252c4a4e1dd6010
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6782
Tested-by: build bot (Jenkins)
|
|
The register indexes and bitfield masks were guarded by the UART8250 config
options, but it might be (is) necessary to use them in a driver that is
UART8250 like without actually using the 8250 driver itself. To avoid any name
collision with other drivers, also change the constant prefix from UART_ to
UART8250_.
Change-Id: Ie606d9e0329132961c3004688176204a829569dc
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/171336
Reviewed-by: Ronald Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit a93900be8d8a8260db49e30737608f9161fbf249)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6715
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
Use CONSOLE_POST because the preprocessor conditional in post_code()
in src/console/post.c depends on it, while POST_IO is used in another
conditional for sending the codes to an I/O port.
Change-Id: Ia044cffb5f0aad0f8b2bb04faa12df11a705757a
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Reviewed-on: http://review.coreboot.org/6416
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Fixed spelling and added empty lines to separate the help
from the text automatically added during make menuconfig.
Change-Id: I6eee2c86e30573deb8cf0d42fda8b8329e1156c7
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Reviewed-on: http://review.coreboot.org/6313
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Without this change, removal of default UART_FOR_CONSOLE entries
under mainboard/ Kconfig will remove this option entirely from
created .config file.
Change-Id: I11422ddb8c51abca177f999936c995ae0c91c459
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5626
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
We have means to easily disable a specific console in romstage if
necessary, so this global option makes little sense.
The option was initially introduced as a work-around for build issues
around CACHE_AS_RAM, ROMCC and ARCH_ARMV7 dependencies for UARTs.
Change-Id: I797bdd11a48ddd813d3ee7ccef9a0c050f16f669
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5607
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The port for console remains to be a compile time constant.
The Kconfig option is changed to select an UART port with index
to avoid putting map of UART base addresses in Kconfigs.
With this change it is possible to have other than debug console
on different UART port.
Change-Id: Ie1845a946f8d3b2604ef5404edb31b2e811f3ccd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5342
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Option DRIVERS_UART builds with support for UART hardware.
Option CONSOLE_SERIAL enables the console output for UART.
Those x86 boards that do not have serial port on SuperIO should select
NO_UART_ON_SUPERIO to disable 8250 UART for the default configuration.
Removes:
CONSOLE_SERIAL_UART
HAVE_UART_IO_MAPPED
HAVE_UART_MEMORY_MAPPED
Renames:
CONSOLE_SERIAL8250 -> DRIVERS_UART_8250IO
CONSOLE_SERIAL8250MEM -> DRIVERS_UART_8250MEM
Change-Id: Id3afa05f85c0d6849746886db8b6c2ed6c846b61
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5311
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: If92b50ab3888518228d2d3b76f5c50c4aef968dd
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/4561
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
This menu may become a bit more complicated with addition of
new USB hardware so move it out of console/.
Change-Id: Ieb330675b9227a3e53d093f7c2b5a65e3842dc82
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5307
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
If there is trouble setting up usbdebug, it may be useful to delay
usbdebug init to run in ramstage.
Change-Id: I31de5a06d3f9ce19f71c422cce0c8cb0fd50f396
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4488
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
No need to show the choice of USB port or controller in case of older
hardware where location for usbdebug was hardwired.
Change-Id: Ia186bf2c6ed60be2834cf6fd0a1965c8bf81ed4d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4290
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This was used by Ron 13ys ago and was never used again
ever since.
Change-Id: I8ae8a570d67fa0b34b17c9e3709845687f73c724
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/59320
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: http://review.coreboot.org/4256
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This can be used to indicate sub-state within a POST
code range which can assist in debugging BIOS hangs.
For example this can be used to indicate which device
is about to be initialized so if the system hangs
while talking to that device it can be identified.
Change-Id: I2f8155155f09fe9e242ebb7204f0b5cba3a1fa1e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58104
Reviewed-on: http://review.coreboot.org/4229
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The main usbdebug file lib/usbdebug.c was removed from romstage
build with commit f8bf5a10 but the chipset-specific parts were not,
leading to unresolved symbol errors for AMD platforms.
Add a silent Kconfig variable USBDEBUG_IN_ROMSTAGE for convenient
use of this feature.
Change-Id: I0cd3fccf2612cf08497aa5c3750c89bf43ff69be
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3983
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
As boards without EARLY_CBMEM_INIT do not initialize CBMEM in romstage,
and have no CAR migration, these features are available for ramstage only.
Change-Id: Ic3f77ccdedd4e71ba693619c02c9b98b328a0882
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3970
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
This reverts commit de1fe7f655c549e8dce5b34218221890fa5ccc34.
While things appeared to work, there were actually invalid references
to CAR storage after CAR was torn down on boards without
EARLY_CBMEM_INIT. It was discussed use of CAR_GLOBAL should be
restricted to boards that handle CAR migration properly.
Change-Id: I9969d2ea79c334a7f95a0dbb7c78065720e6ccae
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3968
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Assume EARLY_CBMEM_INIT=y everywhere and remove option from Kconfig.
If romstage does not make the cbmem_initialize() call, features like
COLLECT_TIMESTAMPS and early CBMEM_CONSOLE will execute during
romstage, but that data will get lost as no CAR migration is
executed.
Change-Id: I5615645ed0f5fd78fbc372cf5c3da71a3134dd85
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3917
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Some development kits with USB 2.0 HS OTG have an USB hub instead
of being directly connected to the USB host/device controller.
Send the necessary initialisation sequence, using HUB CLASS requests
of PORT_POWER and PORT_RESET to enable a pre-selected port number
where a device supporting debug descriptor is located.
This also adds the Kconfig option for BeagleBone.
Change-Id: I7a5d0ba0962a9ca06bf3196232ed4a03bdfb2b06
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3925
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Nowadays, chipsets or boards do not only have one USB port with the
capabilities of a debug port but several ones. Some of these ports are
easier accessible than others, so making them configurable is also necessary.
This change adds infrastructure to switch between EHCI controllers,
but does not implement it for any chipset.
Change-Id: I079643870104fbc64091a54e1bfd56ad24422c9f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3438
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
On AMD platforms, setting of USBDEBUG_DEFAULT_PORT=0 tries to scan
all physical ports one after other in incrementing order. To avoid
possible problems with other USB devices, one can select the port
number here and bypass the scan.
Intel platforms can communicate with usbdebug dongle on one
physical port only, and this option makes no difference there.
Change-Id: I45be6cc3aa91b74650eda2d444c9fcad39d58897
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3872
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Add Kconfig option SQUELCH_EARLY_SMP and have it enabled by
default.
Console drivers have unpredictable results if multiple threads
attempt to share same resources without spinlock. Serial UARTs
have not had huge problems, only distorted output, but those
relying on cache-as-ram (CBMEM and usbdebug) may require this.
Change-Id: I7f406fdea7b6dc6a341c4da2fab56f7b7ff568b4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3854
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
This change brings back the possibility to disable console
output while in romstage, like before commit d2f45c65.
For some platforms (AMD multi-socket) USBDEBUG and/or CBMEM
CONSOLE do not work correctly for romstage due the way
cache-as-ram is set up, but might already work for ramstage.
Change-Id: Id8d830e02a18129af419d3b5860866acf315d531
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3846
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: I6b28bb95c7decbe3eed33b5b5a029bee48bbe403
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3691
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
It might be that you want an early console in romstage before RAM is up, but
you can't or don't want to support the console all the way back in the
bootblock. By making the console in those two different environments
configurable seperately that becomes possible.
On the 5250 console output as early as the bootblock works, but on the 5420 it
only starts working in the ROM stage after clocks have been initialized.
Change-Id: I68ae3fcb4d828fa8a328a30001c23c81a4423bb8
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3671
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ibcc0a94638c022a76cd3c2e3387af6e1ab757ccb
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3337
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add support for sending debug output to an I/O port.
It can be used together with QEMU's isa-debugcon driver to log the
coreboot output to a file. The port is configurable and defaults
to 0x402 which has established as the de facto standard. For example,
SeaBIOS+OVMF [1] use that one too.
[1] http://www.linux-kvm.org/page/OVMF
Open Virtual Machine Firmware
Change-Id: I0803f7fc70030242f80003e25c9449c37d71975e
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3331
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
binary
This option has never had much if any use. It solved a problem over 10
years ago that resulted from an argument over the value or lack thereof
of including all the debug strings in a coreboot image. The answer is
in: it's a good idea to maintain the capability to print all messages,
for many reasons.
This option is also misleading people, as in a recent discussion, to
believe that log messges are controlled at build time in a way they are
not. For the record, from this day forward, we can print messages at all
log levels and the default log level is set at boot time, as directed by
DEFAULT_CONSOLE_LOGLEVEL. You can set the default to 0 at build time and
if you are having trouble override it in CMOS and get more messages.
Besides, a quick glance shows it's always set to max (9 in this case) in
the very few cases (1) in which it is set.
Change-Id: I60c4cdaf4dcd318b841a6d6c70546417c5626f21
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3188
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ie497e4c8da05001ffe67c4a541bd24aa859ac0e2
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/2987
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There are assumptions that COLLECT_TIMESTAMPS and CONSOLE_CBMEM
rely on EARLY_CBMEM_INIT. This isn't true in the face of
DYNAMIC_CBMEM as it provides the same properties as EARLY_CBMEM_INIT.
Therefore, allow one to select COLLECT_TIMESTAMPS and CONSOLE_CBMEM
when DYNAMIC_CBMEM is selected. Lastly, don't hard code the cbmem
implementation when COLLECT_TIMESTAMPS is selected.
Change-Id: I053ebb385ad54a90a202da9d70b9d87ecc963656
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2895
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Early console should always be allowed to be turned on / off (for generating
production and debug versions), and should not be enforced by "select" Kconfig
rule.
A new "DEFAULT_EARLY_CONSOLE" is introduced for devices to select if they
prefer early console output by default.
Verified Kconfig value on qemu/x86 (default y by CACHE_AS_RAM), snow/x86
(default y by EXYNOS5 config), and intel/jarrell (default n).
Change-Id: Ib1cc76d4ec115a302b95e7317224f1a40d1ab035
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2307
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
The console drivers (especially serial drivers) in Kconfig were named in
different styles. This change will rename configuration names to a better naming
style.
- EARLY_CONSOLE:
Enable output in pre-ram stage. (Renamed from EARLY_SERIAL_CONSOLE
because it also supports non-serial)
- CONSOLE_SERIAL:
Enable serial output console, from one of the serial drivers. (Renamed
from SERIAL_CONSOLE because other non-serial drivers are named as
CONSOLE_XXX like CONSOLE_CBMEM)
- CONSOLE_SERIAL_UART:
Device-specific UART driver. (Renamed from
CONSOLE_SERIAL_NONSTANDARD_MEM because it may be not memory-mapped)
- HAVE_UART_SPECIAL:
A dependency for CONSOLE_SERIAL_UART.
Verified to boot on x86/qemu and armv7/snow, and still seeing console
messages in romstage for both platforms.
Change-Id: I4bea3c8fea05bbb7d78df6bc22f82414ac66f973
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2299
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
This patch makes pre-RAM serial init more generic, particularly for
platforms which do not necessarily need cache-as-RAM in order to use
the serial console and do not have a standard 8250 serial port.
This adds a Kconfig variable to set romstage-* for very early serial
console init. The current method assumes that cache-as-RAM should
enable this, so to maintain compatibility selecting CACHE_AS_RAM will
also select EARLY_SERIAL_CONSOLE.
The UART code structure needs some rework, but the use of ROMCC,
romstage, and then ramstage makes things complex.
uart.h now includes all .h files for all uarts. All 2 of them.
This is actually a simplifying change.
Change-Id: I089e7af633c227baf3c06c685f005e9d0e4b38ce
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2086
Tested-by: build bot (Jenkins)
|
|
Change-Id: I5b412678bb8993633b3a610315d298cb20c705f3
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2011
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Because they use outb instructions, they are bound to fail
on non-PC80 systems like ARM.
Change-Id: I679ac6c0964c06c369cc90556529bb6f629d56f9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1974
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
|
|
This adds more configurability to POST codes. The current assumption
is that POST codes should be written to an IO port (e.g. LPC) if POST
codes are enabled. This changes the assumption so that POST codes can
be written to the serial console without being written to an IO port.
This enables POST codes by default using "default y" to avoid
changing current behavior.
Change-Id: I3db91c358ccb1557096983c4d07f70b2e872c4b3
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/1685
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This will use 3 bytes of CMOS to keep track of the POST
code for the current boot while also leaving a record of
the previous boot.
The active bank is switched early in the bootblock.
Test:
1) clear cmos
2) reboot
3) use "mosys nvram dump" to verify that the first byte
contains 0x80 and the second byte contains 0xF8
4) powerd_suspend and then resume
5) use "mosys nvram dump" to verify that the first byte
contains 0x81 and the second byte contains 0xFD
Change-Id: I1ee6bb2dac053018f3042ab5a0b26c435dbfd151
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
- cash -> Cache
- make the new size of the cbmem console buffer the default
Change-Id: Ia906077257e93622ad56bc54a42f8184ade78b29
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/726
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Some experiments have demonstrated that total amount of text
generated by coreboot console when BIOS_SPEW level is enabled
exceeds 40KB.
Console output generated before DRAM is initialized can exceed
2KB. This patch introduces the new configuration option and
assigns adequate default values to cache based and DRAM based
console buffers.
BUG=chrome-os-partner:4200
TEST=manual
. run the following commands in the root directory
cp config.stumpy .config
make menuconfig
. enable the new option (Console->Send console output to a CBMEM buffer)
. save the configuration
Observe the following settings added to the config:
+CONFIG_CONSOLE_CBMEM=y
+CONFIG_CONSOLE_CBMEM_BUFFER_SIZE=0xae00
+CONFIG_CONSOLE_CAR_BUFFER_SIZE=0xc00
Change-Id: I209603f516244ae136631e6281ba21ebc6fb1710
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://gerrit-int.chromium.org/5855
Tested-by: Vadim Bendebury <vbendeb@google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/718
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
trivial change in src/console/Kconfig
Change-Id: Ib6bb4ccfabaa3af18b48a23a51a576b872d807a8
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Reviewed-on: http://review.coreboot.org/505
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Add a configuration option POST_PORT which defaults to 0x80 and
can be redefined by boards which have integrated POST displays
on another I/O port. Change post.c to output POST codes to this
port instead of 0x80 hardcoded.
Change-Id: I8f8e820f8c75641b35e7249bf622b63a3604b9f3
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/221
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
example.
This newer version reflects the recent changes to further simplify the console
code and partly gets rid of some hacks in the previous version.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6544 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
because that is what it does.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6311 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6244 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
initializing VGA happens pretty much as the last thing before starting the
payload. Hence, drop VGA console support, as we did in coreboot v3.
- Drop VGA and BTEXT console support.
Console is meant to be debugging only, and by the time graphics comes up
99% of the risky stuff has already happened. Note: This patch does not remove
hardware init but only the actual output functionality.
The ragexl driver needs some extra love, but that's for another day
- factor out die() and post()
- drop some leftover RAMBASE < 0x100000 checks.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: QingPei Wang<wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
It cannot be changed via software according to the datasheet, whereas
this is indeed possible on AMD SB700. I tested using the SB700 mechanism
on SB600 but it didn't work, so I suspect the datasheet is indeed correct.
Thus, don't show the kconfig option for selecting the physical USB port
on the AMD SB600 southbridge.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5906 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
USB port for use as Debug Port (on chipsets which support that).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5860 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
