| Age | Commit message (Collapse) | Author |
|---|
|
If a port is connected before and after an xhci controller reset, the
PORTSC CSC bit may not be asserted. Add an additional check in
xhci_rh_port_status_changed for the PRC bit so we can correctly handle
ports in such a state.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I2d623aae647ab13711badd7211ab467afdc69548
Reviewed-on: https://chromium-review.googlesource.com/189394
Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit ee7c3ea182b35bb6ce3c62f301c4515714f6e654)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/7002
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The generic roothub reset port function is overly broad and does some
things which may be undesirable, such as issuing multiple resets to a
port if the reset is deemed to have finished too quickly. Remove the
generic function and replace it with a controller-specific function,
currently only implemented for xhci.
Change-Id: Id46f73ea3341d4d01d2b517c6bf687402022d272
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/189495
Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit 54e1da075b0106b0a1f736641fa52c39401d349d)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/7001
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Forgot an asterisk and everything goes to hell. Sorry about that.
Change-Id: I6b2503ca3ea0f80d4e4e5d8b8c0e986fec5db2c9
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/173587
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: David James <davidjames@chromium.org>
(cherry picked from commit 2a357560a697b56cc6022a4dd3dda47b33568d83)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6854
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The dump_td() debug function in the EHCI stack incorrectly masks the
amount of transferred bytes on output... the actual field is 15 bits
wide (30:16). Let's just use the mask constant we already have for all
the other code.
Change-Id: I28c6f0ec75cc613e38d53b670645d19bf9ffe1b9
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/174986
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
(cherry picked from commit 570077da7f16bbe2204b4a80790e4bd8fe1a2bd7)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6853
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This patch represents a major overhaul of the USB enumeration code in
order to make it cleaner and much more robust to weird or malicious
devices. The main improvement is that it correctly parses the USB
descriptors even if there are unknown descriptors interspersed within,
which is perfectly legal and in particular present on all SuperSpeed
devices (due to the SuperSpeed Endpoint Companion Descriptor).
In addition, it gets rid of the really whacky and special cased
get_descriptor() function, which would read every descriptor twice
whether it made sense or not. The new code makes the callers allocate
descriptor memory and only read stuff twice when it's really necessary
(i.e. the device and configuration descriptors).
Finally, it also moves some more responsibilities into the
controller-specific set_address() function in order to make sure things
are initialized at the same stage for all controllers. In the new model
it initializes the device entry (which zeroes the endpoint array), sets
up endpoint 0 (including MPS), sets the device address and finally
returns the whole usbdev_t structure with that address correctly set.
Note that this should make SuperSpeed devices work, but SuperSpeed hubs
are a wholly different story and would require a custom hub driver
(since the hub descriptor and port status formats are different for USB
3.0 ports, and the whole issue about the same hub showing up as two
different devices on two different ports might present additional
challenges). The stack currently just issues a warning and refuses to
initialize this part of the hub, which means that 3.0 devices connected
through a 3.0 hub may not work correctly.
Change-Id: Ie0b82dca23b7a750658ccc1a85f9daae5fbc20e1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170666
Reviewed-by: Kees Cook <keescook@chromium.org>
(cherry picked from commit ecec80e062f7efe32a9a17479dcf8cb678a4a98b)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6780
Tested-by: build bot (Jenkins)
|
|
This patch removes the confusing concept of a special "xhci_speed" with
a different numeric value from the usual speed used throughout the USB
core (except for the places directly interacting with the xHC, which are
explicitly marked). It also moves the MPS0 decoding function into the
core and moves some definitions around in preparation of later changes
that will make the stack SuperSpeed-ready. It makes both set_address
implementations share a constant for the specification-defined
SetAddress() recovery delay and removes pointless additional delays from
the non-XHCI version.
Change-Id: I422379d05d4a502b12dae183504e5231add5466a
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170664
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Ronald Minnich <rminnich@chromium.org>
(cherry picked from commit f160d4439c0d7cea1d2e6b97207935d61dcbb2f2)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6776
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch fixes a bug in the XHCI stack that occurs when a multi-TRB TD
times out before the last TRB is processed. The driver will correctly
issue a Stop Endpoint command in that case, but the xHC will still
preserve the transfer state and just pick up right after that on the
next doorbell ring. It will then process the leftover TRBs from the old
TD the next time a transfer is issued. (cf. XHCI 4.6.9)
We fix this by changing the existing xhci_reset_endpoint() calls in
transfer functions to not only trigger on Halted (2) and Error (4), but
also on Stopped (3). That function will not actually issue a Reset
Endpoint command in this case, but it will nuke the whole transfer ring
and issue a Set TR Dequeue Pointer command, which is sufficient (though
slightly overkill) to solve our problem.
Change-Id: I3abbe30ff9d4911a8af1f792324e018d427019e8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170833
Reviewed-by: Ronald Minnich <rminnich@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
(cherry picked from commit f12424af0e29ac12963e8e5a7970fadcc0bb6cee)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6787
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
While the 8250 compatible serial port driver is primarily useful on x86
systems because it works with the legacy x86 com ports, some devices which
aren't x86 based have 8250 compatible UARTs as well. This change renames the
CONFIG_X86_SERIAL_CONSOLE option to the more general and direct
CONFIG_8250_SERIAL_CONSOLE and fixes up the dependencies so that non-x86
systems can enable the driver, although it will default to on on x86 and off
otherwise.
Also, the default IO port address that's added to the sysinfo structure on x86
and which is intended to be overwritten by a value in the coreboot tables is
not used on ARM. That variable is adjusted so that it's more clear it's a
default value, and made dependent on x86 since that's the only place its value
is actually used.
Change-Id: Ifeaade0e7bd76d382426e947275a9c933da4930e
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/170834
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 9a10e39a2da3cb0bfb316c0869cf5025078e287f)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6655
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The existing USB_MEMORY mechanism to instantiate non-PCI host
controllers is clunky and inflexible... most importantly, it doesn't
allow multiple host controllers of the same kind. This patch replaces it
with a function that allows payloads to directly instantiate as many
host controllers of whatever type they need.
Change-Id: Ic21d2016a4ef92c67fa420bdc0f0d8a6508b69e5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169454
Reviewed-by: Stefan Reinauer <reinauer@google.com>
(cherry picked from commit b6e95c39dd91f654f0a345f17b3196f56adf4891)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6644
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This patch fixes the following minor bugs in the USB stack:
1. Ensure that all dynamically allocated device structures are cleaned
on detachment, and that the device address is correctly released again.
2. Make sure MSC and HID drivers notice missing endpoints and actually
detach the device in that case (to prevent it from being used).
3. Make sure XHCI-specific set_address() cleans up all data structures
on failure.
4. Fix broken Slot ID range check that prevented XHCI devices from being
correctly cleaned up.
Change-Id: I7b2b9c8cd6c5e93cb19abcf01425bcd85d2e1f22
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170665
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Ronald Minnich <rminnich@chromium.org>
Tested-by: Ronald Minnich <rminnich@chromium.org>
(cherry picked from commit 9671472263ddd0c30400ae3b6da780a18cd21ded)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6701
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The USB MSC device structure contains a "ready" state that can be either
"ready", "not ready" or "detached". The last one can only be assigned
when the device is completely unresponsive and gets forcefully logically
detached via usb_detach_device(). This call (at least in the current
version) also calls all destructors and frees the complete usbdev_t
structure (including the MSC specific part), which unfortunately makes
storing the "detached" state in that very structure a little pointless.
This patch reduces the "ready" value to a simple boolean and makes sure
that all detachment cases immediately return from the MSC driver,
carefully avoiding any use-after-free opportunities.
Change-Id: Iff1c0849f9ce7c95d399bb9a1a0a94469951194d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170667
(cherry picked from commit fd4529f37fdd1c93a8b902488ffeef7001b1a05a)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6654
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This patch updates the libpayload XHCI stack to run on ARM CPUs (tested
with the DWC3 controller on an Exynos5420). Firstly, it adds support for
64-byte Slot/Endpoint Context sizes. Since the existing context handling
code represented the whole device context as a C struct (whose size has
to be known at compile time), it was necessary to refactor the input and
device context structures to consist of pointers to the actual contexts
instead.
Secondly, it moves all data structures that the xHC accesses through DMA
to cache-coherent memory. With a similar rationale as in the ARM patches
for EHCI, using explicit cache maintenance functions to correctly handle
the actual transfer buffers in all cases is presumably impossible.
Instead this patch also chooses to create a DMA bounce buffer in the
XHCI stack where transfer buffers which are not already cache-coherent
will be copied to/from.
Change-Id: I14e82fffb43b4d52d687b65415f2e33920e088de
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169453
Reviewed-by: Stefan Reinauer <reinauer@google.com>
(cherry picked from commit 1fa9964063cce6cbd87ba68334806dde8aa2354c)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6643
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch makes the EHCI driver work on ARM platforms which usually do
not support automatic cache snooping. It uses the new DMA memory
mechanism (which needs to be correctly set up in the Coreboot mainboard
code) to allocate all EHCI-internal communication structures in
cache-coherent memory, and cleans/invalidates the externally supplied
transfer buffers in Bulk and Control functions with explicit calls as
necessary.
Old-Change-Id: Ie8a62545d905b7a4fdd2a56b9405774be69779e5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167339
(cherry picked from commit 322338934add36a5372ffe7d2a45e61a4fdd4a54)
libpayload: ehci: Cache management is hard, let's go copying...
It turns out that my previous commit to make the EHCI stack cache aware
on ARM devices wasn't quite correct, and the problem is actually much
trickier than I thought. After having some fun with more weird transfer
problems that appear/disappear based on stack alignment, this is my
current worst-case threat model that any cache managing implementation
would need to handle correctly:
Some upper layer calls ehci_bulk() with a transfer buffer on its stack.
Due to stack alignment, it happens to start just at the top of a cache
line, so up to 64 - 4 bytes of ehci_bulk's stack will share that line.
ehci_bulk() calls dcache_clean() and initializes the USB transfer.
Between that point and the call to dcache_invalidate() at the end of
ehci_bulk(), any access to the stack variables in that cache line (even
a speculative prefetch) will refetch the line into the cache. Afterwards
any other access to a random memory location that just happens to get
aliased to the same cache line may evict it again, causing the processor
to write out stale data to the transfer buffer and possibly overwrite
data that has already been received over USB.
In short, any dcache_clean/dcache_invalidate-based implementation that
preserves correctness while allowing any arbitrary (non cache-aligned)
memory location as a transfer buffer is presumed to be impossible.
Instead, this patch causes all transfer data to be copied to/from a
cache-coherent bounce buffer. It will still transfer directly if the
supplied buffer is already cache-coherent, which can be used by callers
to optimize their transfers (and is true by default on x86).
Old-Change-Id: I112908410bdbc8ca028d44f2f5d388c529f8057f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169231
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
(cherry picked from commit 702dc50f1d56fe206442079fa443437f4336daed)
Squashed the initial commit and a follow up fix.
Change-Id: Idf7e5aa855b4f0221f82fa380a76049f273e4c88
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6633
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The readwrite_chunk was private to the usb mass storage driver, but wasn't
marked as static which was upsetting the compiler.
Change-Id: I0ef5c5f96a29f793dd43ff672a939902bad13c45
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/169816
Reviewed-by: Julius Werner <jwerner@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 8140e6145b3d072b7f12a924418570022207c065)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6648
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Currently, we wait for up to 30 seconds for a device to become ready to
respond to a TEST_UNIT_READY command. In practice, all media devices become
ready much sooner. But, certain devices do not function with libpayload's
USB driver, and always timeout. To provide a better user experience when
booting with such devices, reduce the timeout to 5 seconds.
Change-Id: Icceab99fa266cdf441847627087eaa5de9b88ecc
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169209
(cherry picked from commit 9e55204e92adca0476d273565683f211d6803e7a)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6647
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
When bringing up media, we claim to wait for up to 30 seconds for a
device to respond to our TEST_UNIT_READY command. Actually, we can wait
far longer because we do not take into account execution delay.
To improve timeout accuracy, make use of gettimeofday(), which calculates
time based upon a CPU counter. This improves the user experience
slightly when certain non-working USB devices are used.
Change-Id: Id9605ecfc0a522d7a0b039fd8eac541232605082
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169208
Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit 1d3d535db83ff478c512e37f37015b43927b3efc)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6646
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add a new function to split transfer requests into chunks of
64KB in order to be as compatible as possible with devices that
choke when sent large transfer requests.
Change-Id: Id11990bd149af14af5535de4af47bda21d1ab51e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169170
Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit 4c413b007aa23da830877127dd556c4c38b43042)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6636
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The current USB hub code always clears the port status change after
checking it, regardless of whether it was set in the first place. Since
this check runs on every poll, it might create a race condition where
the port status changes right between the GET_PORT_STATUS and the
CLEAR_FEATURE(C_PORT_CONNECT), thus clearing the statrus change flag
before it was ever read. Let's add one extra if() to avoid that possible
headache.
Change-Id: Idd46c2199dc6c240bd9ef068fbe70cccc88bac42
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168098
(cherry picked from commit f7f6f008f701ab3e4a4f785032d8024d676e11cb)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6617
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The EHCI host controllers in Samsung Exynos SoC seem to be a little more
picky than Intel ones. When they reach the dummy_qh in the periodic
frame list, they try to access the next qTD pointer even though it's
NULL, and run into a HostSystemError. This patch explicitly sets the
Terminate bit on those pointers to mark them invalid.
Change-Id: I50fa79bbf1c5fab306d7885c01efd66b13e279b8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66884
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
(cherry picked from commit c575a5c958ce88732d28044352c89418bcd5ea86)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6608
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The USB bulk and control transfer functions in libpayload currently
always return 0 for success and 1 for all errors. This is sufficient for
current use cases (essentially just mass storage), but other classes
(like certain Ethernet adapters) need to be able to tell if a transfer
reached the intended amount of bytes, or if it fell short.
This patch slightly changes that USB API to return -1 on errors, and the
amount of transferred bytes on successes. All drivers in the current
libpayload mainline are modified to conform to the new error detection
model. Any third party users of this API will need to adapt their
if (...<controller>->bulk/control(...)) checks to
if (...<controller>->bulk/control(...) < 0) as well.
The host controller drivers for OHCI and EHCI correctly implement the
new behavior. UHCI and the XHCI stub just comply with the new API by
returning 0 or -1, but do not actually count the returned bytes.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48308
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Updated the patch to support XHCI as well.
Change-Id: Ic2ea2810c5edb992cbe185bc9711d2f8f557cae6
(cherry picked from commit e39e2d84762a3804653d950a228ed2269c651458)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6390
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The current XHCI code only sets IOC on the last TRB of a TD, and
doesn't set ISP anywhere. On my Synopsys DesignWare3 controller, this
won't generate an event at all when we have a short transfer that is not
on the last TRB of a TD, resulting in event ring desync and everyone
having a bad time. However, just setting ISP on other TRBs doesn't
really make for a nice solution: we then need to do ugly special casing
to fish out the spurious second transfer event you get for short
packets, and we still need a way to figure out how many bytes were
transferred. Since the Short Packet transfer event only reports
untransferred bytes for the current TRB, we would have to manually walk
the rest of the unprocessed TRB chain and add up the bytes. Check out
U-Boot and the Linux kernel to see how complicated this looks in
practice.
Now what if we had a way to just tell the HC "I want an event at exactly
*this* point in the TD, I want it to have the right completion code for
the whole TD, and to contain the exact number of bytes written"? Enter
the Event Data TRB: this little gizmo really does pretty much exactly
what any sane XHCI driver would want, and I have no idea why it isn't
used more often. It solves both the short packet event generation and
counting the transferred bytes without requiring any special magic in
software.
Change-Id: Idab412d61edf30655ec69c80066bfffd80290403
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170980
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
(cherry picked from commit e512c8bcaa5b8e05cae3b9d04cd4947298de999d)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6516
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
You might want to use the serial hardware for something other than a console,
or you might want to intercede in the serial stream to wrap it in another
protocol. This is what you'd do to send output to GDB while using it to debug
the payload.
Change-Id: I2218c0dbb988dacb64e5bdaf5d92138828eff8b6
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/179559
Reviewed-by: Ronald Minnich <rminnich@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit da9ab46d974745125fe7d8b29ce43336c3586cd5)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6547
Tested-by: build bot (Jenkins)
|
|
When libpayload header files are included in the payload itself, it's possible
that the payloads config settings will conflict with the ones in libpayload.
It's also possible for the libpayload config settings to conflict with the
payloads. To avoid that, the libpayload config settings have _LP_ (for
libpayload) added to them. The symbols themselves as defined in the Config.in files
are still the same, but the prefix added to them is now CONFIG_LP_ instead of just
CONFIG_.
Change-Id: Ib8a46d202e7880afdeac7924d69a949bfbcc5f97
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65303
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 23e866da20862cace0ed2a67d6fb74056bc9ea9a)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6427
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This change makes it possible for vboot to avoid an
exploit that could cause involuntary switch to dev mode.
It gives depthcharge/vboot some information on the
type of input device that generated a key.
BUG=chrome-os-partner:21729
TEST=manually tested for panther
BRANCH=none
CQ-DEPEND=CL:182420,CL:182241,CL:182946
Change-Id: I87bdac34bfc50f3adb0b35a2c57a8f95f4fbc35b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://chromium-review.googlesource.com/182357
Reviewed-by: Luigi Semenzato <semenzato@chromium.org>
Tested-by: Luigi Semenzato <semenzato@chromium.org>
Commit-Queue: Luigi Semenzato <semenzato@chromium.org>
Reviewed-on: http://review.coreboot.org/6003
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Setting of `controller->reg_base` is of no use here, as it is never read
(in another function) later. Looks like this pattern originated from uhci.c
where it makes sense.
By removing the indirection through `reg_base` we also fix a possible
truncation to u32.
Change-Id: I5c99c5bf1f5b1d6c04bd84d87fd3e275fd7d0411
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/6251
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Fix a possible null-pointer dereference (hopefully) before anyone runs
into this. Also don't switch ports to xHCI if initialization failed.
Change-Id: I5dbaeb435a98ead0b50d27fde13c9f1433ea3e81
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/6245
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
As the controller structure is never fully cleared, this one wasn't
initialized for non-pci controllers (but checked for non-null later).
Change-Id: I852671c5f55650bdb6cd97f4ec74b1f95ee894c7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/6246
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Using void* for physical addresses leads to much casting and confuses
developers when to convert from physical to virtual addresses or
the other way around. When using plain integers for physical addresses
and pointers for virtual addresses things become much cleaner and we
won't ever end up dereferencing a physical address.
Change-Id: I24cd53b81c7863b6d14f0cbb4ce8937728b37c1c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/6244
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Like done in FILO, libpayload's console drivers might be initialized
before a relocation. So keep physical pointers in there which won't
break on relocation.
Change-Id: I52e5d9d26801a53fd6a5f3c7ee03f61d6941d736
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/6247
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Remove a redundant phys_to_virt() that sneaked in the initialization of
PCI xHCI controllers. The use of casts from void* to u32 (and vice versa)
prompts for things going wrong here. That will be addressed in a later
commit.
Change-Id: Ibc71ed6ee7016529c0e3a51559aaec07aaaba315
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/6243
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
With coreboot builds with serial console disabled, there is no
CB_TAG_SERIAL entry in coreboot tables. We ended up with
lib_sysinfo.serial == NULL and serial_hardware_is_present == 1.
Change-Id: I9a2fc0b55bf77769f2f2bfbb2b5476bee8083f7d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5723
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Decompartmentalise AHCI driver into two parts, ATA and ATAPI. Add a few
superficial comments while here. This also fixes a compiler warning.
Change-Id: Ia1fd545b39868a81cbc311f6ffc786f9f1f61415
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/4783
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
It resulted in garbage in upper bytes of numeric options.
Change-Id: I5e5d8b770ed93c7e8a1756a5ce32444b6a045bac
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4691
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Code is using it...
Change-Id: I6894b45cbbf70c8e7ce37ce18d93cadf0ea9fbfc
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/4649
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
being a good citizen on the box, libpayload tries to return to EHCI
mode on shutdown, so a non-XHCI capable USB driver after it (eg. in
the OS) finds something to work with.
Change-Id: Id227d646e08a258b841c644263112f0815dd486c
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/4547
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add a function to disable and clear the keyboard controller.
Verified Code flow in normal boot/S3 resume with print statements.
Verified Keyboard was correctly disabled and flushed by booting
to recovery mode screen while pressing keys on the integrated
keyboard.
Change-Id: I3e1f011c3436fee5ce10993c6c26a3c8597c6fca
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63627
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4395
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The EHCI driver defines a maximum transfer timeout of two seconds. The
comments state that during tests the maximum amount of required transfer
time was for the SCSI TEST_UNIT_READY command on certain devices. We
have now observed a USB device (Patriot Memory 13fe:3100) that can NAK
this command for slightly more than two seconds. It will also completely
fail if the timeout hits, since it gets confused by the subsequent CSW
retry/recovery mechanism and starts producing babble errors. This patch
increases the timeout to three seconds to circumvent this problem.
To test, boot a Falco from a red-black RageXT USB stick.
Change-Id: I3c4fef468fb16eacc5a487d76d025a78fb450e27
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63095
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sameer Nanda <snanda@chromium.org>
Reviewed-on: http://review.coreboot.org/4379
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Mass storage devices such as card readers show up as
as USB devices. However the media not be inserted. In those
situations the previous code would just fake a disk and
call usbcreate_disk. This is inappropriate because it forms
a 1:1 mapping of USB device to disk leading to the inability
to remove the disk and/or handle "hot plug" card insertion
and removals.
To alleviate this issue introduce the notion of ready to the
usbmsc structure. It tracks detached, not ready, and ready
states. The polling routine is then used to track not ready
to ready transitions thereby creating and removing disks
appropriately. This handles the case of inserting and removing
a card that shows up as a new disk.
Booted recovery mode. Able to observe inerstion and removal
of sdcard. Also able to insert valid USB flash drive to boot
as well.
Change-Id: I3eefbe537ec1b9c975744b8984b06c17ae236f40
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57948
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4226
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There is currently a hard-coded 30 sec delay in the mass storage
driver while waiting for each device to become ready. However, mass
storage card readers that are empty return an error code on the
TEST UNIT READY command. A REQUEST SENSE command then needs to be
issued and interrogate the data to determine if no media is present.
If no media determination is found to be true the USB device is no
longer considered a candidate to be a disk.
This code does lead to the fact that the media card reader needs to be
populated at enumeration time. I suspect this is not an issue as it
appears the storage stack in libpayload can't handle removable media
coming online later.
Booted recovery and dev modes. Noted that removable mass storage
devices with no media were ignored without any boot delay.
Change-Id: Ida7a45614d97c6e6fbfc9bb099765aad4df550fd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57828
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4225
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Restructure USB stack to not depend on PCI, and
make PCI stub available on x86, but provide fixed
BARs for ARM (Exynos 5)
Change-Id: Iee7c8b134c22b661a9a515e24943470c9dbadd1f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49970
Reviewed-on: http://review.coreboot.org/4175
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Two structures in the USB EHCI stack were pointing
to hardware but not marked attribute((packed)) hence
leaving it to GCC to correctly align the data structures.
Next, the number of reserved bytes in hc_op_t was wrong
(but implicitly aligned to the correct values on x86)
It seems this worked fine on x86, but on ARM it was doing
the wrong thing.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I94bed4850ded7d3f7bbc7ff3079c103c6054c22d
Reviewed-on: https://gerrit.chromium.org/gerrit/55555
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4174
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On Intel's Panther Point the xHCI ports are shared with an EHCI
controller. Our xHCI driver switches them to xHCI, naturally. But
we forgot to switch them back on shutdown, which left them
unusable by a non-xHCI aware operating system.
Change-Id: I70ef08655a603b42ee939935d50cf77ea97878a3
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3791
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
keyboard_init attempts to read the existing mode register, set the
'XLATE' bit, and write it back. The implementation is buggy because the
keyboard may be active at the time we read the mode, and we can
misinterpret scancode data as the reply to our command. It leads to
problems where the KB gets disabled in firmware.
In fact, setting the 'XLATE' bit is completely unnecessary, even if we
desire QEMU keyboard support. We already set this bit when we initialize
the keyboard in pc_keyboard_init. Basically, this code does nothing
(or worse), so just remove it.
Change-Id: Iab23f03fa8bced74842c33a7d263de5f449bb983
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/3883
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We can't read the drives signature before it's ready, i.e. spun up.
So set the timeout to the standard 30s. Also put a notice on the
console, so the user knows why the signature reading failed.
Change-Id: I2148258f9b0eb950b71544dafd95776ae70afac8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3493
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
A timeout while waiting for a device' signature has shown that our
error path wasn't correct. The shutdown of the ports command engine
always timed out. Fix that by waiting for FR (FIS Receive Running)
to be cleared independently from CR (Command List Running) and after
clearing FRE (FIS Receive Enable).
Change-Id: I50edf426ef0241424456f1489a7fc86a2cfc5753
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3494
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Well, it turned out to be more as some gaps ;)
but we finally have xHCI running. It's well tested against a QM77 Ivy
Bridge board.
We have no SuperSpeed support (yet). On Ivy Bridge, SuperSpeed is not
advertised and USB 3 devices will just work at HighSpeed.
There are still some bit fields in xhci_private.h, so this might need
little more work to run on ARM.
Change-Id: I7a2cb3f226d24573659142565db38b13acdc218c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3452
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is mostly a rewrite, don't even try to read a diff.
Tested with an internal rate matching hub on a QM77 board and three hubs
integrated into DELL monitors.
Change-Id: Ib12fa2aa90af4e0f37143d2ed92c4a1705b6d774
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3451
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The current drivers for external usb hubs and root hubs all follow
the same pattern. Before adding another one with 90% of the same code,
extract the common parts and rewrite them with a simple interface.
This also adds debouncing of new attachments. Current drivers just
waited 100ms before they reset the device. However, we should check
if the device becomes disconnected and reconnected during this period.
Porting of the current hub drivers will take place in separate
commits (when I have time to test the older HCIs).
Change-Id: I0c0ce0ac1b1cc51fb4cd009b3f9fcd1b9d2ba8fe
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3450
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Read bInterval from endpoint descriptors and store it in our endpoint_t
struct. The interval is encoded dependently on the device' speed and the
endpoint's type. Therefore, it will be normalized to the binary logarithm
of the number of microframes, i.e.
t = 125us * 2^interval
The interval attribute will be used in the xHCI driver.
Change-Id: I65a8eda6145faf34666800789f0292e640a8141b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3449
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
xHCI requires special treatment of set_address since it determines
the device number itself (instead of the driver, as with the other
controllers). The controller also wants to validate a chosen device
configuration and we need to setup additional structures for the
device and the endpoints.
Therefore, we add three functions to the hci_t structure, namely:
set_address()
finish_device_config()
destroy_device()
Current implementation for the Set Address request moved into
generic_set_address() which is set_address() for the UHCI, OCHI and
EHCI drivers. The latter two are only provided as hooks for the xHCI
driver.
The Set Configuration request is moved after endpoint enumeration.
For all other controller drivers nothing changes, as there is no other
device communication between the lines where the set_configuration()
call moved.
Change-Id: I6127627b9367ef573aa1a1525782bc1304ea350d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3447
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
During device initialization, skip any non-endpoint descriptor before
reading the endpoint descriptors. By now, only HID descriptors were
skipped.
Change-Id: I190f3ae44b864aa71d5f32c3738097cf8f33a61b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Add the Mobile Panther Point (PPT) AHCI controller (DEVID 0x1e03) to
the list of tested controllers. Also comment the only other listed
controller (Mobile ICH9).
The PPT AHCI controller was tested with a QM77 chipset on a Kontron
KTQM77 board.
Change-Id: Ia396761411f4f9289af11ec8e1b144512b2fc126
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3361
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This fixes the configuration where serial console output is
being sent to non-existant hardware to be captured with I/O
trapping. In this configuration where there isn't serial
hardware present we still want to init the consoles. We just
never want to read non-existant hardware.
Change-Id: Ic51dc574b9c0df3f6ed071086b0fb2119afedc44
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3249
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Reading commit »libpayload: New AHCI, ATA and ATAPI drivers«
(1f6bd94f) [1], the spelling error was found and is now fixed.
[1] http://review.coreboot.org/1622
Change-Id: Id418bcb99c1a9a400a49fc04078e465bd0908074
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3071
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This change modifies the code in libpayload that scans the PCI hierarchy for
USB controllers. Previously, if a devices primary function (function 0) was a
bridge, then none of the other functions, if any, would be looked at. If one
of the other functions was a bridge, that wouldn't be handled either. The new
version looks at each function that's present no matter what, and if it
discovers that it's a bridge it scans the other side.
Change-Id: I37f269a4fe505fd32d9594e2daf17ddd78609c15
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2517
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The function dump_qh() was added a while back but never used.
Hide it behind USB_DEBUG so it doesn't cause warnings when not
debugging the USB stack.
Change-Id: Idb3c7bb214895ef82676d181836a578bf161e8e0
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2909
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
The controller's shutdown function free()s the controller structure so
we shouldn't access it any more after calling shutdown.
As all controllers detach themself, i.e. unchain themself from usb_hcs,
just keep iterating over usb_hcs until it's NULL.
Change-Id: Ie85caba0f685494c3fe04c550a5a14bc4158a94e
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: http://review.coreboot.org/2900
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
It shouldn't be used any more as we're about to free() the memory behind
the controller -- therefore detach it.
Change-Id: I875322a9940570c51d412a7f3bfb6af4ea3b3764
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: http://review.coreboot.org/2899
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
And include the new, split out version in drivers/keyboard.c and
drivers/usb/usbhid.c. Those files were including curses.h just for those
definitions, but the include path was only fixed up to to point to the
libpayload versions of those files if one of the variants of curses was
compiled in. If neither was, gcc would fall back to the system version of that
header which is wrong.
Change-Id: I8c2ee0baf5f0702bd8c713c8dd4613a4bb269ce5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2762
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This function is static and not used in that file. To avoid the compiler
complaining about that fact, put the two functions and the call to dump_ed
(currently #if 0) behind #ifdef USB_DEBUG
Change-Id: Ic373313b5fff81f09800f286b32238350ab699c6
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2716
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
It might be useful to provide a USB driver in the payload itself instead of in
libpayload. For example there are multiple payloads being built and linked
against the same libpayload, and they might not need or even want to have the
same set of drivers installed.
This change adds two new functions, usb_generic_create and usb_generic_remove,
which behave like the usbdisk_create and usbdisk_remove functions which are
defined for USB mass storage devices. If a USB device isn't recognized and
claimed by one of the built in USB class drivers (currently hub, hid, and msc)
and the create function is defined, then it will be called to give the payload
a chance to use the device. Once it's removed, if usb_generic_remove is
defined it will be called, effectively giving the payload notice.
Built and booted depthcharge on Link. Built depthcharge for Daisy. Built
a netbooting payload, called usb_poll() with those functions implemented, and
verified that they were called and that the devices they were told about were
reasonable and the same as what was reported by lsusb in the booted system.
Change-Id: Ief7c0a513b60849fbf2986ef4ae5c9e7825fef16
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2666
Tested-by: build bot (Jenkins)
Reviewed-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
EHCI controllers see transfers as a queue of transfer descriptors
(qTDs), each of which can represent an aligned area of up to 20KB. Each
qTD is processed separately, which means that a single USB packet cannot
span multiple qTDs.
While this should not be a problem according to the specification, some
USB storage devices seem to get confused when a packet in the middle of
a transfer is smaller than the maximum packet size (512 bytes) due to
falling on a qTD boundary. This patch aligns the total transfer length
per qTD to 512 bytes to avoid that problem (any excess bytes will simply
roll over to the next qTD).
Change-Id: I0b5db07507699a3861b30c1a5ee774c45dda7fdd
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/2651
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Initialize the high part of the address
and use 64-bit compatible descriptors.
(waste a few bytes on 32-bit but should be harmless)
Read USB stick on a SandyBridge system which has 64-bit EHCI.
Change-Id: I59cc842459acecdde8f8bdd4795ebfeccb842c8f
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2650
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I56f810dfa6654ac1e9d1696ad15e7f1b8bfe59bd
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2652
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I01b1fa42139af925716cd5d57f96dc24da6df5a7
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2660
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I36c750d520ff034c9ca9b9af46bd99bd49af7355
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2659
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This way we won't have two copies of the hardware init function, and three
copies of the putchar, havechar, and getchar functions.
Change-Id: Ifda7fec5d582244b0e163ee93ffeedeb28ce48da
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2657
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The functions defined in that header aren't used anywhere in the actual code,
and that include breaks things on ARM.
Built for ARM with COREBOOT_VIDEO_CONSOLE turned on and saw compiler
errors go away.
Change-Id: I56d6fe5e00c8fccda6e31ef8752326bd36398e74
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2656
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
That way when it's treated as a u32 when its value is extracted for numblocks
and blocksize below, it doesn't make the compiler unhappy, and it ensures that
the buffer will be properly aligned on architectures where that sort of thing
matters.
Built and saw warnings about type punning go away.
Change-Id: I254e0b5e70847112d660675b7df0ac9cb52e4051
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2653
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This function was using mdelay in a loop to check for the completion of an USB
controller operation. Since we're busy waiting anyway, we might as well wait
only 1 us before checking again and potentially seeing the completion 999 us
earlier than we would otherwise.
Change-Id: I177b303c5503a0078c608d5f945c395691d4bd8a
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2522
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
When checking to see if a PCI device exists at a particular bus/dev/func,
libpayload was checking the vendor and device id fields together against a 16
bit 0xffff. The two fields together are 32 bits, however, so the check was
never true, and all dev/func combinations on a particular bus would be
checked. That was slightly wasteful, but had relatively small impact.
Change-Id: Iad537295c33083243940b18e7a99af92857e1ef2
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2521
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Not only were these files checked in with the Chromium OS Authors
copyright, but in addition they were wrongly licensed as GPL.
Switch to 3-clause BSD (and, since we're changing it, fix copyright,
too)
Change-Id: I3656c1f4304d53e343d89bb7c909fd4b929249f4
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2456
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Create a new serial console variable, X86_SERIAL_CONSOLE
which is only enabled when SERIAL_CONSOLE and ARCH_X86 are defined.
Builds for x86 and ARM.
Change-Id: I607253c418de015975a839e3c33577842885ec0c
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2412
Tested-by: build bot (Jenkins)
Reviewed-by: Gabe Black <gabeblack@chromium.org>
|
|
Improve USB debugging for EHCI by adding dump_qh
and enhacing dump_td to dump all queue chain and information.
Change-Id: Ia8ecf19c6dac085cf9558bdf659a5e74ce332714
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/2053
Tested-by: build bot (Jenkins)
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.huber@secunet.com>
|
|
Change-Id: I91b18fadbf17562f8b48e233631653f2a18c037c
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/2063
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
A "far" modifier sneaked into the USB driver, but gcc
doesn't understand it.
Change-Id: I5c67bd55eabce467e1aa107c95c1db2518af7b0e
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2059
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Improved USB debugging for EHCI by enhacing dump_td
to dump all chain information
Change-Id: I8c667b43e09c39ff12aafbd779474efd652bd80f
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/2054
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
|
|
Improving USB debugging for OHCI by enhacing dump_td
and adding dump_ed function to dump all chain information
Change-Id: Ia8b2a9b53e79b1f280fd12ea0d9233fc875e0b57
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/2056
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
|
|
The serial_io_havechar() and serial_io_getchar() functions will
always see keystrokes available if the serial hardware isn't
actually there. We will still output chars to non-existant
hardware to allow virtual hardware to capture them.
Change-Id: I04e85157b6b7a185448abab352b5417a798a397a
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2040
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Previously printf()'s were used to show USB messages
which results in lots of USB information being shown
when it isn't needed. This will now use the usb_debug()
printing funtion that already exists in usb.h.
Change-Id: I2199814de3327417417eb2e26a660f4a5557cb9f
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2044
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
The condition to compare the labels was twisted.
Change-Id: I34a665aa87e2ff0480eda0f249bbbea8a8fe68d8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1941
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Slightly more complete keymap
Change-Id: I4fef6b8f75ab07cb20a3a8ccd7eaad81c9fe719f
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1922
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We have to free TDs more carefully if they have been processed by the
controller yet. The current code tries to force the controller to post
them back to the done queue, but that seems wrong. We can't be sure,
when they get written back. This resulted in leaking TDs with an invalid
reference to a freed interrupt queue.
The new approach: Mark the interrupt queue to be destroyed and handle
the freeing later, when the controller posted the last TD to the done
queue.
Change-Id: I79d80a9dc89e1ca79dc125c4bbccbf23664227b3
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1905
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The connection state detection in the OHCI root hub driver was broken if
you used more than one device per root hub.
Change-Id: Ica5c735426beac45ef6f591ce68a72d8283a00f5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1904
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
If somethings goes wrong during an interrupt transfer, drop the
transfer.
Change-Id: I450c08a7a0bf23fbee74237e0355d4a726ace114
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1901
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
If usb_poll() isn't called fast enough, the UHCI controller marks an
underrun interrupt queue as done (terminating the queue at the head).
We can recover from this situation, when usb_poll() gets called again,
and the queue is processed.
Change-Id: Id56c9df44d6dbd53cd30ad89dfb5bf5977799829
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1898
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The linking of interrupt queues into UHCI controller's framelist (in
uhci_create_intr_queue()) was incomplete. The implementation of
uhci_destroy_intr_queue() was even worse, looking like it wanted to
clean up more than uhci_create_intr_queue() did.
This patch follows the simple approach that we used for OHCI and EHCI:
Each slot in the framelist holds only one interrupt queue. Therefore, we
have to look for free slots each time we want to link an interrupt queue
into the framelist. In return, we have a much simpler structured
framelist.
With this, USB devices using interrupt transfers (e.g. keyboards) can be
detached cleanly from UHCI controllers. Also, more than one of such
devices can be attached without further risk.
Change-Id: I07b81a3b6f2cb3ff69515c973b3ae6321ad969aa
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1897
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The USB HID driver had some static variables with keyboard state. This
moves them to the driver's instance, so multiple attached keyboards
don't effect each other.
Change-Id: I3f1ccfdea95062b443cebe510abf2f72fdeb1916
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1907
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Prevent race conditions, when an interrupt-queue underrun occurred and
the controller is currently working on our queue head or a transfer is
still in progress.
Change-Id: Ia14f80a08071306ee5d1349780be081bfacb206a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1902
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
When a USB hub got removed, we should also remove all devices that
were attached to it.
Change-Id: I73c0da1b7570f1af9726925ca222781b3d752557
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1903
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
If an endpoint gets stalled by an MSC device, after successful
transmission of a command (CBW), we should still ask for the status
(CSW). Otherwise, the driver and the device get desynchronized on the
command tags.
Change-Id: I53167f22c43b3a237cb4539b3affe37799378b93
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1900
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Stalled transfers are not fatal, so don't spew on the console on every
tiny failure.
Change-Id: I175c1e83a6af09c1abbd43d045ed6dbf0c79f871
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1899
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
dump_td() is orphaned but looks useful => commented out.
The delay identifier shadowed the global one => renamed to total_delay.
Change-Id: I4f3766a07db9194b2552ebf9302bd7ef8a66371f
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1895
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
We can trust free() and memset() to work correctly on volatile
references, so cast volatile pointers to (void *) when calling them.
Change-Id: Ieff7f78133b72f303349cca0a0ca3bbf37ec52bb
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1896
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
usb_controller_initialize() is not declared in any header file nor
called from outside of usbinit.c, so make it static.
set_configuration() looks like beeing non-static on purpose (like the
other helpers around it in usb.c), so put a prototype into usb.h.
Change-Id: I08d93b3769d8398bb43462d9afdfeec81fef93ec
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1894
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
We had mixed virtual and physical pointers in struct sysinfo_t. Some
being virtual by accident which led to problems when we tried to
reinitialize lib_sysinfo after relocating FILO (to get intentionally
virtual pointers valid again). I guess this didn't cause much trouble
before, as lib_get_sysinfo() was always called with physical addresses
being equal to their virtual counterparts.
For FILO, two possibilities seem practical: Either, have all pointers in
struct sysinfo_t physical, so relocation doesn't hurt. Or, have all
pointers virtual and call lib_get_sysinfo() again after relocation.
This patch goes the latter way, changing the following pointers for
situations where virtual pointers differ from physical:
.extra_version
.build
.compile_time
.compile_by
.compile_host
.compile_domain
.compiler
.linker
.assembler
.cb_version
.vdat_addr
.tstamp_table
.cbmem_cons
.mrc_cache
We could also just correct the accidentally virtual pointers. But, IMO,
this would lower the risk of future confusion.
Note 1: Looks like .version gets never set.
Note 2: .option_table and .framebuffer were virtual pointers but treated
like physical ones. Even in FILO, this led to no problems as
they were set before relocation.
Change-Id: I4c456f56f049d9f8fc40e62520b1d8ec3dad48f8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1855
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
uhci_reset() differs in semantics compared to the other HCI's reset()
implementations. uhci_reset() does some initialization work after a
controller reset. So move the initialization part to a new function,
uhci_reinit(), which get's exported through a new entry in hci_t:
hci_t.init().
Warning: This breaks code that relies on the current, special,
counterintuitive behaviour of uhci_reset(). If one wants a working host
controller after calling hci_t.reset(), he should call hci_t.init()
afterwards.
Change-Id: Ia7ce80865d12d11157645ce251f77f349f8e3c34
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1851
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
When ohci_reset() was implemented, OHCI controllers stopped working
since the stub ohci_reset() is called at the end of ohci_init().
This is fixed by removing the call. To prevent further problems the call
to the xhci_reset() stub is removed, too.
Change-Id: If89825c8e6caf40f7f4fe078e8b2e90054a54ba2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1850
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
All shutdown() implementations but ehci_shutdown() free the hci_t
structure. This seems correct and the reference to the hci_t shouldn't
be used after shutdown(), so do it in ehci_shutdown(), too.
Change-Id: Ie3506d769e73007735f3211710734a5f0107e43a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1849
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
FILO can use this as offset to enumerate AHCI and its own IDE
devices together.
Change-Id: I57380e7bd1df6db5c882427e9a34d068f4348fb2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1846
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
