| Age | Commit message (Collapse) | Author |
|---|
|
Original firmware ships with PTT enabled by default on poweron.
PTT takes priority over SPI/LPC TPM so enable the CRB interface
until coreboot implements a way to select the interface and adapt
the API to handle any TPM detection.
TEST=Boot the board and see PTT is detected by Windows and Linux
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I74dc2c4245388a9f134b27e313ef26124b952594
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63834
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the full PCIe root port configuration. Proper initialization of
the root ports depends on the correct GPIO programming including
virtual wires. Do not program the CLKREQ signals in coreboot to let FSP
detect and configure CLKREQ pads. Otherwise the CLKREQ pads are
reprogrammed by FSP despite having GpioOverride=1. The pads that
should not be touched by coreboot are left commented in the board GPIO
file. CLKREQ reprogramming caused undefined behavior when ASPM and
Clock PM was being enabled by coreboot on PCIe endpoints of CPU PCIe
x4 slot (coreboot printed a lot of exceptions and simply halted).
TEST=Boot the MSI PRO Z690-A DDR4 WiFi with all PCIe/M.2 slots
populated and check if they are detected and functional in Linux.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I50199d2caf54509a72c5100acb770bf766327e7f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63656
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Initial mainboard code MSI PRO Z690-A DDR4 WIFI. The platform boots up
up to romstage where it returns from FSP memory init with an error.
What works:
- open-source CAR setup
- NCT6687D serial port with TX pin exposed on JBD1 header
- SMBus reading SPD from all 4 DIMMs
This board will serve as a reference board for enabling Alder Lake-S
support in coreboot. More code and functionalities will be added in
subsequent patches as src/soc/alderlake code will be improved for
PCH-S.
TEST=Extract the microcode from vendor firmware and include it in the
build. The platform should print the console on the serial port even
without FSP blob.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I5df69822dbb3ff79e087408a0693de37df2142e8
Signed-off-by: Igor Bagnucki <igor.bagnucki@3mdeb.com>
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
|
|
Branding changes to unify and update Chrome OS to ChromeOS (removing the
space).
This CL also includes changing Chromium OS to ChromiumOS as well.
BUG=None
TEST=N/A
Change-Id: I39af9f1069b62747dbfeebdd62d85fabfa655dcd
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65479
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
This patch does the following:
- Allow selecting 64bit from Kconfig
- Fix up integer to pointer conversion that gcc complains about
- Add a buildtest target in configs
Tested on Thinkpad X200: boots fine to the payload
Change-Id: Icb9c31a28ee231b87109b19c00ce2f8b48b5aefe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add initial implementation for booting on QEMU POWER9 emulation.
Change-Id: I079c5b9ad564024dd13296ef75c263bdc40c9d39
Signed-off-by: Yaroslav Kurlaev <yaroslav.kurlaev@3mdeb.com>
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Change-Id: If30d715c5a3b44be2832c96316003dc9d139b53f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59695
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that CBFS verification is available as an optional feature in
menuconfig (CB:59982), we should add build test configs to ensure it
doesn't break without notice. One Arm and one x86 board should be good
enough for now.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I530dfd37472e63b80a67badd22a13d54d2c4621b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
Build-test the configuration Prodrive uses to build coreboot for their
Hermes mainboard.
Change-Id: I62e79d3143851bf14dfdbe70e60c60f13dd06c3f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Justin van Son <justin.van.son@prodrive-technologies.com>
|
|
CONFIG_ONBOARD_SAMSUMG_MEM was used to force Samsung memory.
CPLD is used to determine the memory type leaving CONFIG_ONBOARD_SAMSUNG_MEM unused.
Remove this config.
BUG = N/A
TEST = Boot Facebook FBG1701 Rev 1.0 - 1.4
Change-Id: I60626552f2e2338cf5cbaaf4dca1b1eb2756d8df
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59755
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This config selected ADD_FSP_BINARIES even though HAVE_INTEL_FSP_REPO is
only defined for Apollolake and not Geminilake that resides in the same
SoC directory and uses the same Kconfig file. This results in the paths
to the FSP binaries not being defined, in which case the
ADD_FSP_BINARIES option shouldn't be selected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I95123c4930b44a3b76c87768e130eb7359bbf625
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Also add a config file to ensure the code gets build-tested.
Change-Id: I530eccd2a194bc79de5ee354d98260d93423cd5b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53986
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Relying on the implicit defaults for these settings can cause issues in
the future. For example, commit 8cc4c5a1e76c0c8aee3a14618c15d38e3bd2bd61
(config.dell_optiplex_9010_sff: Specify board model) was done to prevent
a build failure when adding support for other Dell mainboards which make
the default board change.
Change-Id: Ie0da6254def8b38e9fb053fc7d530dfb46760861
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56079
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I755f2037bc9368e610eb97a2633aa66da7f626b0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56042
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add defconfig to build test x86_64 code on Sandy Bridge.
Change-Id: I2c18af8bfa87636c68741e4759059276c287d052
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrik Tesarik <depate@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Introduce `USE_EXP_X86_64_SUPPORT` in `src/arch/x86/Kconfig` and guard
it with `HAVE_EXP_X86_64_SUPPORT`. Replace the per-CPU implementations
of the same functionality with the newly-added Kconfig options. Update
documentation and the config file for QEMU accordingly.
Change-Id: I550216fd2a8323342d6b605306b0b95ffd5dcd1c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This updates the intel-sec-tools submodule pointer to include a fake
acm binary to be included for buildtesting.
Change-Id: Id4a9e177f71306b8c5538a578da229a53d19487a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Use the same code from Lynx Point on Broadwell, and adjust as needed.
Also add a config file to ensure the code gets build-tested.
Tested on out-of-tree Compal LA-A992P (Haswell ULT), UART 0 works.
Change-Id: I527024098738700d5fbaf3e27cf4db331a0322bd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Derived from Broadwell and adapted to follow what soc/intel does. Note
that SERIALIO_UART_CONSOLE is meant to be selected from the mainboards
which expose a SerialIO UART. UART_FOR_CONSOLE also needs to be set in
mainboard Kconfig accordingly.
It is possible that some of the UART configuration steps in bootblock
are unnecessary. However, some of the steps turn off power management
features and others are undocumented: omitting them could cause weird
issues.
Finally, add a config file to ensure the code gets build-tested.
Tested on out-of-tree Compal LA-A992P, SerialIO UART 0 can be used to
receive coreboot and SeaBIOS logs.
Change-Id: Ifb3460dd50ed03421a38f03c80f91ae9fd604022
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52489
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add `CONFIG_BOARD_DELL_OPTIPLEX_9010=y` to avoid issues when other Dell
mainboards get added.
Change-Id: Ice2073a3073a345aeb9ead7398cb4129453dd5ba
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
OCP Delta Lake is developed and validated against LinuxBoot payload.
Need to put the respective binary blobs in site-local/deltalake to
build the final coreboot image.
Add LINUX_COMMAND_LINE for LinuxBoot payload kernel cmdline,
CPU_UCODE_BINARIES for CPU microcode binary, CONSOLE_SERIAL_57600 is
the serial baud rate used by OCP Delta Lake, DEFAULT_CONSOLE_LOGLEVEL_4
is for a faster boot time.
Tested=On OCP Delta Lake it can boot up target CentOS 8 GNU/Linux OS.
Change-Id: Ib494e4170a7ebb445d9e11df83c370b40a9e5194
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55058
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We would like to have an easy way to completely disable TPM support on a
board. For boards that don't pre-select a TPM protocol via the
MAINBOARD_HAS_TPMx options, this is already possible with the
USER_NO_TPM option. In order to make this available for all boards, this
patch just removes the whole USER_TPMx option group and directly makes
the TPM1 and TPM2 options visible to menuconfig. The MAINBOARD_HAS_TPMx
options can still be used to select defaults and to prevent selection of
a protocol that the TPM is known to not support, but the NO_TPM option
always remains available.
Also fix some mainboards that selected TPM2 directly, which they're not
supposed to do (that's what MAINBOARD_HAS_TPM2 is for), and add a
missing dependency to TPM_CR50 so it is set correctly for a NO_TPM
scenario.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib0a73da3c42fa4e8deffecb53f29ee38cbb51a93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Change-Id: I536a104428ae86e82977f2510b9e76715398b442
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Tested with TianoCore payload (UefiPayloadPkg).
Working:
- PS/2 keyboard, touchpad
- Both DIMM slots
- Both NVMe ports
- SATA port
- All USB ports
- Webcam
- Ethernet
- Integrated graphics using Intel GOP driver
- Internal microphone
- Internal speakers
- S3 suspend/resume
- Flashing with flashrom
- Booting to Ubuntu Linux 20.10 and Windows 10
Not working:
- Discrete/Hybrid graphics
This requires a new driver to work correctly, which will be added and
enabled later.
Change-Id: I10667fa26ac7c4b8eb67da11f3e963062bd0db47
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47822
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The artifacts can then be run on test system.
Change-Id: I2300af7b9be5fbb42a874566971854b93292885e
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51293
Reviewed-by: Harshit Sharma <harshitsharmajs@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The idea is to get rid of having 2 different smmloaders so add this
option only to qemu/q35 to get it buildtested.
Change-Id: Id4901784c4044e945b7f258b3acdc8d549665f3a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51525
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is meant to build-test Crashlog and various debug options.
Change-Id: Ie9bbfa538e38a4d835c1f8b0d45feb2f0fe803f8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Francois Toguo Fotso <francois.toguo.fotso@intel.com>
|
|
This build-tests ASan support for both romstage and ramstage, because
the Haswell northbridge selects the HAVE_ASAN_IN_ROMSTAGE option. x86
Kconfig selects the HAVE_ASAN_IN_RAMSTAGE option, and Haswell is x86.
Change-Id: I892881d2315c09aa6d9d80903a8399d0f4d648e4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Harshit Sharma <harshitsharmajs@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
To replace wiki page https://www.coreboot.org/Board:gigabyte/ga-g41m-es2l
+ configs/config.gigabyte_ga-g41m-es2l
+ lshw output examples
+ memory modules compatibility
Tested in Devuan 4 Chimaera.
Tested from exact steps from this documentation.
Change-Id: Ib45cfea15b43d7399e9d209f7ba7c6b24fe860dd
Signed-off-by: Alexey Vazhnov <vazhnov@boot-keys.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evgeny Zinoviev <me@ch1p.io>
|
|
Tested with TianoCore payload (UefiPayloadPkg).
Working:
- PS/2 keyboard, touchpad
- Both DIMM slots
- Both NVMe ports
- SATA port
- All USB ports
- Webcam
- Ethernet
- Integrated graphics
- Internal microphone
- S3 suspend/resume
- Flashing with flashrom
- Booting to Ubuntu Linux and Windows
Not working:
- Discrete/Hybrid graphics
- Internal speakers
These two require new drivers to work correctly, which will be added and
enabled later.
Change-Id: Iae6e530dcd52df3642cdfe74b65bfff5aa0dd402
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
With top-aligned bootblock this is no longer globally needed.
The default maximum is now a generous 256 KiB with couple
platforms having lower limits of 32 KiB and 64 KiB.
Change-Id: Ib1aee44908c0dcbc17978d3ee53bd05a6200410c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This is not meant for actual use, but to build-test several options.
Please do not try to use it on real hardware. Or maybe do try.
The purpose of this config is to build-test the individual options, not
their combination. So, for instance, if it would be hard to keep options
x, y and z build together in the future, this config shouldn't block a
change but should instead be adapted, e.g. split into multiple chunks.
Change-Id: I80e8fe3982025b61148e7c2b05dd0727d65ee2f4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Signed-off-by: Julien Viard de Galbert <julien@vdg.name>
Change-Id: I39fd9aabe7285d39e1883622ee9d6a60c6651b6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This is not meant for actual use, but to build-test several options.
Please do not try to use it on real hardware. Or maybe do try.
The purpose of this config is to build-test the individual options, not
their combination. So, for instance, if it would be hard to keep options
x, y and z build together in the future, this config shouldn't block a
change but should instead be adapted, e.g. split into multiple chunks.
Change-Id: Ife40d055e4c9b295c54cfc6a27af06e9358f7761
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45974
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This allows build-testing the code while it isn't used anywhere.
Change-Id: I754c661fbad0bc5fbddfab9747607e664ad1e2b6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44174
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The purpose of this config is to build-test the individual options, not
their combination. So, for instance, if it would be hard to keep options
x, y and z build together in the future, this config shouldn't block a
change but should instead be adapted, e.g. split into multiple chunks.
Change-Id: Ibd8f6513fae6cd02fcf889d2510dc7e0a97ce40c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47068
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This config selects the necessary options to enable Intel TXT on the
Asrock B85M Pro4, and allows the code to be build-tested. Note that the
current TXT code will not work, as it was written for Broadwell-DE.
Subsequent commits will adapt the code as necessary to work on Haswell.
Compatible BIOS and SINIT ACMs can be retrieved from a firmware update
for the Supermicro X10SLH. As they are not in the blobs repository, use
the STM binary as a placeholder so as to allow build-testing the code.
Change-Id: Ibf8db5fdfac5b527520023277c6370f6efa71717
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46489
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Looks like the option is generally not compatible with
garbage collections. Nothing is inlined, is_smp_boot()
no longer evaluates to constant false and thus the symbols
from secondary.S would need to be present for the build
to pass after we set SMP=n.
Change-Id: I1b76dc34b5f39d8988368f71a0a2f43d1bc4177e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43817
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add additional build config to test qemu-i440fx x86_64 code.
Change-Id: I63f7a6e1602728e4d5ff67f9bd702efebe315c16
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This allows build-testing the code while it isn't used anywhere.
Change-Id: Ib0b78cf874ab28d2b6ed687c1a63bcca3d788d2c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This config is meant to build-test several options, such as SMMSTORE,
UBSAN, SIL3114 driver, EM100 support, code coverage and debug options.
Please do not try to use it on real hardware. Or maybe do try.
Change-Id: I8bc19a1987b405d5a654276050b00b956acbdf36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43977
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add TXT ramstage driver:
* Show startup errors
* Check for TXT reset
* Check for Secrets-in-memory
* Add assembly for GETSEC instruction
* Check platform state if GETSEC instruction is supported
* Configure TXT memory regions
* Lock TXT
* Protect TSEG using DMA protected regions
* Place SINIT ACM
* Print information about ACMs
Extend the `security_clear_dram_request()` function:
* Clear all DRAM if secrets are in memory
Add a config so that the code gets build-tested. Since BIOS and SINIT
ACM binaries are not available, use the STM binary as a placeholder.
Tested on OCP Wedge100s and Facebook Watson
* Able to enter a Measured Launch Environment using SINIT ACM and TBOOT
* Secrets in Memory bit is set on ungraceful shutdown
* Memory is cleared after ungraceful shutdown
Change-Id: Iaf4be7f016cc12d3971e1e1fe171e6665e44c284
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Otherwise, Jenkins doesn't pick up the file, and STM doesn't get
build-tested.
Change-Id: I7cf23c8352f82b2672c7ff25efba0057b8e059cd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eugene Myers <cedarhouse1@comcast.net>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Replace uses with MAINBOARD_HAS_LPC_TPM, if drivers/pc80/tpm
is present in devicetree.cb it is necessary to always include
the driver in the build.
Change-Id: I9ab921ab70f7b527a52fbf5f775aa063d9a706ce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner
|
|
OCP Delta Lake server is a one socket server platform powered by
Intel Cooper Lake Scalable Processor.
The Delta Lake server is a blade of OCP Yosemite V3 multi-host
sled.
TESTED=Successfully booted on both YV3 config A Delta Lake server
and config C Delta Lake server. The coreboot payload is Linux kernel
plus u-root as initramfs. Below are the logs of ssh'ing into a
config C deltalake server:
jonzhang@devvm2573:~$ ssh yv3-cth
root@ip's password:
Last login: Mon Apr 20 21:56:51 2020 from
[root@dhcp-100-96-192-156 ~]# lscpu
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 52
On-line CPU(s) list: 0-51
...
[root@dhcp-100-96-192-156 ~]# cbmem
34 entries total:
0:1st timestamp 28,621,996
40:device configuration 178,835,602 (150,213,605)
...
Total Time: 135,276,123,874,479,544
[root@dhcp-100-96-192-156 ~]# cat /proc/cmdline
root=UUID=f0fc52f2-e8b8-40f8-ac42-84c9f838394c ro crashkernel=auto selinux=0 console=ttyS1,57600n1 LANG=en_US.UTF-8 earlyprintk=serial,ttyS0,57600 earlyprintk=uart8250,io,0x2f8,57600n1 console=ttyS0,57600n1 loglevel=7 systemd.log_level=debug
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Change-Id: I0a5234d483e4ddea1cd37643b41f6aba65729c8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Based on the autoport. The OptiPlex 9010 comes in four different sizes:
MT, DT, SFF and USFF. Tested on SFF only. The other PCBs are slightly
different, but they are designed with intercompatibility in mind. With
small devicetree overrides it should work on OptiPlex 7010 and other
OptiPlex 9010 variants as well.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I88d65cae30d08ca727d86d930707c2be25a527cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40351
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Jenkins does not build using .config.facebook_fbg1701 on new patches.
Rename the config file adding '.mboot_vboot'. Now FACEBOOK_FBG1701
and FACEBOOK_FBG1701_MBOOT_VBOOT are included in Jenkins test result.
BUG=N/A
TEST=Build and boot Facebook fbg1701
Change-Id: Ib54cc29e7ff34553c19fa3502872d6e7aee5fbe8
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40557
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I379a5664776624600ff1c2919bffa77c877d87ab
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add a defconfig which allows to place a large uImage/FIT payload
in it to boot test the binary on qemu-system-aarch64 using u-root
and kexec-tools.
Change-Id: I95ca187b68ff883152421bd7612b494cd63e8d02
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
We can make our lifes much easier by removing its dependency on
`ADD_FSP_BINARIES`. Instead, we imply the latter if the repository
is to be used. We can also hide a lot of unnecessary prompts in
this case.
Also, remove default overrides and selects for the two that are
now unnecessary.
Change-Id: I8538f2e966adc9da0fbea2250c954d86e42dfeb3
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39882
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I2a2de7ccb96996211c45da3f9ec9bf6f71cc0c89
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Add config file that can be used to build a fully working
Tioga Pass image.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: Ifff3591ef9fff40117c60e85900bde9c3729bd94
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
It wasn't picked up by the builder due to wrong file name.
Change-Id: Ia31b5d304a0cabd0d578c5ac6181cb1c8ee1c246
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I32fc8a7d3177ba379d04ad8b87adefcfca2b0fab
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
OCP platform Tiogapass is a 2-socket server platform, which
is based on a chipset including Intel Skylake-SP processors
and a Lewisburg PCH. Skylake-SP is a processor in Intel Xeon
Scalable Processor family.
Following ACPI tables are added:
DSDT/SSDT, MADT, FACP, FACS, HPET, MCFG, SLIT, SRAT, DMAR
This patchset is tested on a Tiogapass board. It booted with
Linux kernel 4.16.0; lscpu command shows all 72 cpus (2 sockets,
18 cores, 2 thread per core); ssh command shows
networking is up from Mellanox ConnectX-4 PCIe NIC card.
Towards successful gerrit buildbot build, note that:
* microcode is in coreboot intel-microcode submodule repo.
* IFD binary is included in this patch.
* Dummy ME binary is used, as it may take long time for Intel
ME binary to be available in public domain.
* Fake FSP binary is used, as at this moment the SKX-SP
FSP binary is not going to be available in public domain.
Known issues (Not intend to address in this initial support for
Xeon-SP processors):
* c6 state is not supported.
* dsdt table is not fully populated, such as processor/socket
devices, some PCIe devices.
* SMM handlers are not added.
Following are some command execution with CentOS booted from
local SATA disk:
[root@localhost ~]# lscpu
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 72
On-line CPU(s) list: 0-71
Thread(s) per core: 2
Core(s) per socket: 18
Socket(s): 2
NUMA node(s): 2
Vendor ID: GenuineIntel
CPU family: 6
Model: 85
Model name: Intel(R) Xeon(R) Gold 6139 CPU @ 2.30GHz
Stepping: 4
CPU MHz: 140.415
BogoMIPS: 4626.46
Virtualization: VT-x
L1d cache: 32K
L1i cache: 32K
L2 cache: 1024K
L3 cache: 25344K
NUMA node0 CPU(s): 0-17,36-53
NUMA node1 CPU(s): 18-35,54-71
[root@localhost ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.23.68.190 netmask 255.255.0.0 broadcast 172.23.255.255
inet6 2620:10d:c082:9063:268a:7ff:fe57:5af0 prefixlen 64 //cut
inet6 fe80::268a:7ff:fe57:5af0 prefixlen 64 scopeid 0x20<link>
inet6 2620:10d:c082:9063::5d2 prefixlen 128 scopeid 0x0<global>
ether 24:8a:07:57:5a:f0 txqueuelen 1000 (Ethernet)
RX packets 84249 bytes 6371591 (6.0 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8418 bytes 748781 (731.2 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 613 bytes 63906 (62.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 613 bytes 63906 (62.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[root@localhost ~]# cbmem
36 entries total:
// Lines were cut to avoid checkpatch.pl warnings
Total Time: 96,243,882,140,175,829
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Tested-by: johnny_lin@wiwynn.com
Change-Id: I29868f03037d1887b90dfb19d15aee83c456edce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
This time, it failed to build if measured boot was not enabled. Fix this
problem, and make sure flashconsole will not break like that again.
Change-Id: I5f5ffd14a3225804524cb0c1518e3d99737e0a93
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This update is a combination of all four of the patches so that the
commit can be done without breaking parts of coreboot. This possible
breakage is because of the cross-dependencies between the original
separate patches would cause failure because of data structure changes.
security/intel/stm
This directory contains the functions that check and move the STM to the
MSEG, create its page tables, and create the BIOS resource list.
The STM page tables is a six page region located in the MSEG and are
pointed to by the CR3 Offset field in the MSEG header. The initial
page tables will identity map all memory between 0-4G. The STM starts
in IA32e mode, which requires page tables to exist at startup.
The BIOS resource list defines the resources that the SMI Handler is
allowed to access. This includes the SMM memory area where the SMI
handler resides and other resources such as I/O devices. The STM uses
the BIOS resource list to restrict the SMI handler's accesses.
The BIOS resource list is currently located in the same area as the
SMI handler. This location is shown in the comment section before
smm_load_module in smm_module_loader.c
Note: The files within security/intel/stm come directly from their
Tianocore counterparts. Unnecessary code has been removed and the
remaining code has been converted to meet coreboot coding requirements.
For more information see:
SMI Transfer Monitor (STM) User Guide, Intel Corp.,
August 2015, Rev 1.0, can be found at firmware.intel.com
include/cpu/x86:
Addtions to include/cpu/x86 for STM support.
cpu/x86:
STM Set up - The STM needs to be loaded into the MSEG during BIOS
initialization and the SMM Monitor Control MSR be set to indicate
that an STM is in the system.
cpu/x86/smm:
SMI module loader modifications needed to set up the
SMM descriptors used by the STM during its initialization
Change-Id: If4adcd92c341162630ce1ec357ffcf8a135785ec
Signed-off-by: Eugene D. Myers <edmyers@tycho.nsa.gov>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: ron minnich <rminnich@gmail.com>
|
|
Change-Id: Ie1d0a2ed9aa5c0645fa8400ec9af17be592d3dea
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38581
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Keith Hui <buurin@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The System76 Lemur Pro (lemp9) is an upcoming laptop computer. Support
in coreboot is developed by System76 and provided as the default
firmware option. Testing is done on a pre-production model expected to
be identical from a firmware perspective to the production model.
Working:
- Payload
- Tianocore
- CPU
- Intel i7-10510U
- Intel i5-10210U
- EC
- ITE IT5570E running https://github.com/system76/ec
- Backlit Keyboard, with standard PS/2 keycodes and SCI hotkeys
- Battery
- Charger, using AC adapter or USB-C PD
- Suspend/resume
- Touchpad
- GPU
- Intel UHD Graphics 620
- GOP driver is recommended, VBT is provided
- eDP 14-inch 1920x1080 LCD
- HDMI video
- USB-C DisplayPort video
- Memory
- Channel 0: 8-GB on-board DDR4 Samsung K4AAG165WA-BCTD
- Channel 1: 8-GB/16-GB/32-GB DDR4 SO-DIMM
- Networking
- M.2 PCIe/CNVi WiFi/Bluetooth
- Sound
- Realtek ALC293D
- Internal speaker
- Internal microphone
- Combined headphone/microphone 3.5-mm jack
- HDMI audio
- USB-C DisplayPort audio
- Storage
- M.2 PCIe/SATA SSD-1
- M.2 PCIe/SATA SSD-2
- RTS5227S MicroSD card reader
- USB
- 1280x720 CCD camera
- USB 3.1 Gen 2 Type-C (left)
- USB 3.1 Gen 2 Type-A (left)
- USB 3.1 Gen 1 Type-A (right)
Not working:
- TPM2 - SPI bus 0, chip select 2 is used. Chip selects other than 0
are not currently supported by the intel fast_spi driver.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ib0a32bbc6f89a662085ab4a254676bc1fad7dc60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I70467862b238f8be62eafb5532ede9882dd2f41a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38174
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If stage cache is enabled, we should not allow S3 resume
to load firmware from non-volatile memory.
This also adds board reset for failing to load postcar
from stage cache.
Change-Id: Ib6cc7ad0fe9dcdf05b814d324b680968a2870f23
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch adds a BOARD_GOOGLE_KEVIN variant config that enables
CONFIG_VBOOT_MOCK_SECDATA. This is to ensure that Jenkins will build the
MOCK_SECDATA-specific code at least once, to be sure we don't
accidentally break it during refactoring.
Change-Id: Ib0ffaccdf4601d6bfb889ae289d1d7df18bed1fd
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37773
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Joel Kitching <kitching@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I004fc02bd84b7b8d5c5fb96451e59f143f0fe6d3
Signed-off-by: Praveen Hodagatta Pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This config is a slightly stripped configuration of the Chromium OS
configuration used in production. Apparently the bootblock fills up
faster than usual on this device, resulting in address overflows.
Add this config here so we'll notice early in the future.
Change-Id: I3145bba63d32ddb9d00fd98d3cb774bf9ddd69a6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36923
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable vendorcode measured and verified boot.
Use VBOOT test key for VENDORCODE_ELTAN_VBOOT_KEY_FILE
BUG=N/A
TEST=booting Embedded Linux 4.20 kernel on Facebook FBG1701
Change-Id: Ia2cb3bb873b2d5e7e9031e5b249d86605d8e0945
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I135f3e6ec5e75df03331c0c46edb0be243af2adb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36498
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I21d20d7c575833ace02b4b8ed9d5c82750b331c7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I306d107720d51c2b378f739f68c31b8642f7354a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35615
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I909e9b5fead317928d3513a677cfab25e3c42f64
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34792
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Build test OpenSBI on qemu-riscv-rv64.
Change-Id: I23b9a1b06987d8d8ebb90655162ba4abce1557fa
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34691
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
It would be useful if we have at least one "new" board on which we
actually built vboot, in order to notice if something breaks.
Change-Id: I16c7867e3f0f4e1f2e6ae3918c30789e39881b85
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Not implemented for TSEG.
Change-Id: I279c546a921c0504cafaddcda855bd6ea3de7f8a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Enable VBOOT support on all devices that have a 8 MiB flash, using a
single RW_MAIN_A partition, allowing the use of tianocore payload in
both RW_MAIN_A and WP_RO.
* Add VBNV section to cmos.layout
* Add FMAP for VBOOT and regular boot
* Select Kconfigs for VBOOT
* Enable VBOOT_SLOTS_RW_A by default
Also build test VBOOT on Lenovo T420.
Tested on Lenovo T520 using Icb7b263ed86551cc53e1db7babccaca6b3ae2fe6.
Change-Id: Icb7b263ed86551cc53e1db7babccaca6b3ae2fe6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Iff15e9586cd3e39850d986582b5943cbb8a184a7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This board is EOL and has FSP2.0 support, so drop the older
version.
Change-Id: If5297e87c7a7422e1a129a2d8687fc86a5015a77
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Also add a test case for that, a config taken from chromiumos with some
references to binaries dropped that aren't in our blobs repo (eg audio
firmware).
Change-Id: I411c0bacefd9345326f26db4909921dddba28237
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/29223
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To avoid mangled characters on serial output from iPXE we have to disable
serial from iPXE console. More to that to have correct serial input we
have to enable SeaBIOS SERCON option with default configuration.
The only limitation of this configs is that apu5 doesn't detect iPXE -
that platform is not for public use so it doesn't affect anyone.
Change-Id: I124705bd691b3c8dcd9a2636b17c019d02732c5a
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-on: https://review.coreboot.org/28616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: I2075142a0b241222839899e707a1e3d264746432
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Build tests:
* Option table
* Static option table
* Verbose debugging code
* Sandy Bridge optional Kconfigs
* TPM debugging code
* Lenovo Bluetooth on Wifi
* Libgfxinit on Sandy Bridge
Change-Id: Ib463f578c97a212d0729aa6f54b7b6fba33e0478
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/28118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ia131c8aec1235443465bc017e11f59f38bef76db
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-on: https://review.coreboot.org/26118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add Intel Harcuvar CRB FSP 2.0 sample configuration.
Change-Id: I60ec6921eca17a910cd1b9f8b0b86a1a1bf9bbea
Signed-off-by: Mariusz Szafranski <mariuszx.szafranski@intel.com>
Reviewed-on: https://review.coreboot.org/21693
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: FEI WANG <wangfei.jimei@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add Quark/Galileo configurations to build various test code:
* Galileo Gen1
* Galileo Gen2
* Galileo Gen2 + Quark debugging code
* Galileo Gen2 + FSP 1.1 debugging code
* Galileo Gen2 + FSP 2.0 debugging code
* Galileo Gen2 + SD debugging code
* Galileo Gen2 + vboot
TEST=Build for Galileo Gen1/Gen2
Change-Id: I04358fd9f6a0958b10dad3e01690b0d47e738684
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/20272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Rename `FRAMEBUFFER_KEEP_VESA_MODE` to `LINEAR_FRAMEBUFFER` and put
it together with new `VGA_TEXT_FRAMEBUFFER` into a choice. There are
two versions of `LINEAR_FRAMEBUFFER` that differ only in the prompt
and help text (one for `HAVE_VBE_LINEAR_FRAMEBUFFER` and one for
`HAVE_LINEAR_FRAMEBUFFER`). Due to `kconfig_lint` we have to model
that with additional symbols.
Change-Id: I9144351491a14d9bb5e650c14933b646bc83fab0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Removes the pre-defined VGA bios file and id because
the build system includes every vgabios.
Also make the VGA output primary by default
Change-Id: I87d52ef2d1e151c6e54beba64316fe9043668158
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/18181
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The coreboot builder makes use of the pre defined configuration
files by executing abuild with -d option. These configuration
files contain a basic configuration.
Change-Id: I41470fe7aaa0fdae545ad9d702326a202d0d2312
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/18161
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Test some config options that don't typically get tested.
Change-Id: Ie05c99411c8ce6462a6f5502b086ee2b72a4324b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17591
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
