summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-12-12nb/intel/x4x/rcven.c: Fix programming coarse offsetArthur Heymans
This fixes some bitwise logic errors that caused the coarse offset not to be programmed. This fixes a regression introduced by 6d7a8c "nb/intel/x4x/raminit: Rework receive enable calibration" where the coarse offset doesn't get programmed anymore. TESTED on Foxconn g41s-k on a DIMM where the final DQS receive enable delays are close but above and below the edge of a coarse delay setting. Change-Id: I41869815f782a2ea1178bdea006e3a7587441323 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/22816 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-12-12mb/lenovo/t400/blc.c: Add a new panel to the listArthur Heymans
Also adds a comment in the code to clarify what this array is about. Change-Id: I04b185a5dbd7a7ccb039820f19d2cb549b9a2eac Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/22809 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2017-12-12drivers/intel/gma: Power up legacy VGA block earlyNico Huber
This is required at least on Skylake to be able to configure text mode. 3rdparty/libgfxinit is also updated by the single commit: 42fb2d065d gma: Add procedure to power up legacy VGA block Change-Id: I2fe144765e2b2acd9f6b76db375cae5b8feb5489 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/21386 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-12mb/google/poppy/variants/nami: Implement variant_memory_paramsFurquan Shaikh
This change provides implementation of variant_memory_params for nami. Since it uses DDR4 memory, DQ-DQS mapping table is not required. Also, Rcomp resistor values are provided based on SDP v/s DDP memory. BUG=b:70188937 Change-Id: Ic1d0cfdb7d8b02fa0be0a4c54b20057a4c2fc3ce Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22779 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-11mb/google/poppy/variants/soraka: Tune I2C5 paramsFurquan Shaikh
This change updates scl_lcnt value for I2C5 to bring the bus frequency closer to 400kHz. BUG=b:65062416 TEST=Verified that I2C5 frequency is between 389-396kHz. Change-Id: Ibaccab0c797174332633cb75e30d18ff5af76a43 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22788 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-11soc/amd/common: Move files to common/blockRichard Spiegel
The following files need to be moved: amd_pci_util.c, amd_pci_util.h and spi.c. The remaining files are AGESA related and will be part of a separate issue/commit. BUG=b:62240201 TEST=Build with no error gardenia and kahlee (no code change, just folder reorg). Change-Id: I3f965afa21124d4874d3b7bfe0f404a58b070e23 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/22765 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2017-12-11soc/intel/cannonlake: Add support for D0 steppingLijian Zhao
D0 stepping with CPUID 0x60663 need to be added in coreboot. TEST=Boot up with D0 stepping processor Change-Id: I3b0f2616843367d2bfbee1b5bf75772b9e83e931 Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/22676 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-11google/gru: Stop mucking with unused I2S0 pins in codec configJulius Werner
Due to a schematic error, our code was written to configure more I2S0 pins than are actually used. We're also pinmuxing the whole bank of pins over to the I2S controller even though we don't need them all. Restrict the GPIO initialization and pinmuxing to the pins we really need so the other ones can be correctly used as SKU ID pins on Scarlet. Also, move the "audio" IO voltage domain selection to the other such selections in the bootblock, since that covers two whole banks of GPIOs and there's no guarantee that they're all used for audio (and thus not needed before ramstage). BUG=b:69373077 TEST=Booted Scarlet, confirmed correct SKU ID (7) was detected on rev2. Change-Id: I9314617e725fe83d254984529f269d4442e736f1 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/22791 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: David Schneider <dnschneid@chromium.org>
2017-12-11google/gru: Change Scarlet SKU ID pins to pull-upsJulius Werner
These pins need to be pull-ups. I forgot. BUG=b:69373077 Change-Id: I9314617e01d35898254984529f269d4442e736f1 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/22775 Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-11mainboard/purism/librem_skl: Fix line length > 80 charactersMartin Roth
Make lint-stable was giving an error on this. Change-Id: I06d11d86151f683b82b6df537e3de8c52d33e8b4 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/22811 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Youness Alaoui <snifikino@gmail.com>
2017-12-11soc/amd/common: Collect timestamps before and after AGESA callsMartin Roth
BUG=b:70432544 TEST=Build & boot kahlee. Look at timestamps. Change-Id: I8209160f8e23ab77987f8e515c7b00d94f68c8be Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/22798 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2017-12-11commonlib: Add timestamp codes for AGESAMartin Roth
BUG=b:70432544 TEST=Build & boot kahlee. Look at timestamps. Change-Id: I3bf691a0fb1f5c09e7b6c9965c9e506393ec31f6 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/22797 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-11google/nautilus: Add Maxim98357a supportNaveen Manohar
Adds Maxim98357a support for Nautilus using the generic driver in drivers/generic/max98357 BUG=b:68686020 TEST=With entire merged audio should be enabled on max98357 speaker codec. Change-Id: I958bf7c1395259b3e3fb30332882fd51a48dc0cc Signed-off-by: Naveen Manohar <naveen.m@intel.com> Reviewed-on: https://review.coreboot.org/22458 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-12-11mb/google/poppy/variants/nautilus: add SPK DMIC nhlt supportNaveen Manohar
Nautilus board uses max989357a speaker codec and 4CH DMIC. Select the appropriate NHLT blob to be packaged in CBFS. Also generate the required ACPI NHLT table for codec and the supported topology in nautilus. BUG=b:68686020 TEST=With the required driver support in kernel verify that the Audio plays on Speaker and captures on 4CH DMIC Change-Id: Ie90af02e0935029f53f9020bd78027b6eb31a187 Signed-off-by: Naveen Manohar <naveen.m@intel.com> Reviewed-on: https://review.coreboot.org/22457 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-12-11AMD fam10: Link southbridge/amd/rs780/early_setup.cArthur Heymans
Removes rs780_before_pci_init() since it was a no-op anyway. Removes get_nb_rev() since this function is provided via a macro in the header. This Makes a lot of function non-static since the header has prototypes for these. Change-Id: I8933516771d959583bbd59a5c1beee3e30a7004f Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/20297 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2017-12-11intel: Use MSR_EBC_FREQUENCY_ID instead of 0x2cElyes HAOUAS
Change-Id: Ib1b761fc417f1bb000f408d3bed5e8666963f51d Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/22603 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Martin Roth <martinroth@google.com>
2017-12-11vc/amd/pi/00670F00/binaryPI: cache the AGESA dispatcherAaron Durbin
Instead of repeatedly walking cbfs for the AGESA blob and parsing it cache the resulting dispatcher value. There's only one dispatcher table so use it. The resulting change is that this work is done one time per stage. BUG=b:70401101 TEST=Booted and noted only one lookup per stage. Change-Id: Iaa4aecc384108d66d7c68fc5fb9ac1c3f40da905 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/22789 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Justin TerAvest <teravest@chromium.org>
2017-12-11soc/amd/stoneyridge: Enable SPI writesJohn E. Kabat Jr
- Change soc/amd/stoneyridge/Kconfig to set BOOT_DEVICE_SUPPORTS_WRITES BUG=b:65485690 TEST=Build & boot kahlee. Change-Id: I595a27ac27daa42c2499de1a343bc30be9a89fa6 Signed-off-by: John E. Kabat Jr <john.kabat@scarletltd.com> Signed-off-by: Marc Jones <marcj303@gmail.com> Reviewed-on: https://review.coreboot.org/22636 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-11soc/amd/common: Add amdblocks/spi.hMarc Jones
Add the spi header for spi function prototypes. Fixes spi.c build error for the missing header. Change-Id: I0dbb5bf84cc3462a7aa58a5531d6b8b8bc8ca4df Signed-off-by: Marc Jones <marcj303@gmail.com> Reviewed-on: https://review.coreboot.org/22793 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-12-10sb/intel/i82801jx: Hook up spi codeArthur Heymans
Change-Id: Ie83c800a0bcd12fa501c91a1c2b1ee756de9d732 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/21675 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-12-10sb/intel/common: Add SOUTHBRIDGE_INTEL_COMMON_SPIArthur Heymans
This introduces a Kconfig option to include common Intel SPI code. Change-Id: I970408e5656c0e8812b8609e2cc10d0bc8d8f6f2 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/21674 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2017-12-09Documentation/Intel: Add NativeRaminit documentationPatrick Rudolph
Add documentation for Intel native raminit on Intel SandyBridge. Documented so far: * Register * Read training * Frequency selection * SMBIOS type 17 memory reporting * Various Kconfig options and features Change-Id: I3b977460ecb29c9a54e3fab82349982fca9918e7 Signed-off-by: Patrick Rudolph <siro@das-labor.org> Reviewed-on: https://review.coreboot.org/22275 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-09mb/intel/glkrvp: Add gpio.h in dsdt.asl fileShaunak Saha
Add proper variants gpio.h in dsdt.asl where the GPE_EC_WAKE and EC_SCI_GPI is defined. Change-Id: Ideb6dd4d0ac496a81721cd883865218cb19583d9 Signed-off-by: Shaunak Saha <shaunak.saha@intel.com> Reviewed-on: https://review.coreboot.org/22760 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-09nvramtool: Add dummy cmos-hw-unix accessor implementation for non-x86Paul Kocialkowski
The default implementation uses inb/outb, that is not available on ARM platforms and others. A dummy implementation allows building nvramtool on these platforms. Change-Id: I75e4a1a0cbd35ca40f7b108658686839ccf9784a Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-on: https://review.coreboot.org/22562 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-09soc/intel/skylake: add acoustic noise mitigation params for FSP 1.1Matt DeVillier
Adapted from Chromium commit d6655eb [Skylake: create UPD Interface for acoustic noise tuning] Add FSP 1.1 params needed for acoustic mitigation on google/caroline (to be upstreamed in a subsequent commit). TEST: build/boot google/caroline Change-Id: Ifb36ecef8c1735c63a5322d952929e9c34cddfb9 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/22524 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-09intel/i440bx: Correct RAM init programmingKeith Hui
Corrects MBSC/MBFS programming when initializing DRAM on boards with both 3 and 4 DIMM slots. Reformats comments to current coreboot standards. Drops some romcc "optimizations" no longer necessary. Boot tested on asus/p2b-ls, where it fixes a memory related hang after SeaBIOS resets the board with nothing to boot from. Change-Id: Ib8c21489338643e13f69bd58008d14733796d4d0 Signed-off-by: Keith Hui <buurin@gmail.com> Reviewed-on: https://review.coreboot.org/22687 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-09soc/amd/stoneyridge/include: delete amd_pci_int_types.hRichard Spiegel
Due to review 20b8c821e4 being abandoned and review 376dc82dca being merged, file amd_pci_int_types.h became orphaned (not included by any file), while an array similar to intr_types[] (but that also includes the associated register index) was created in southbridge.c replacing the original array functionality. Remove the header amd_pci_int_types.h from the repository. BUG=b:70328428 TEST=Build kahlee with no errors. Change-Id: I53a9d7ebb27edbc4e136c9b17f5c709930e35223 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/22778 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-09google/cyan: fix FSP memory init paramsMatt DeVillier
In the original Chromium source, PcdMemorySpdPtr is only set for cyan, but none of the other Braswell variants. When upstreamed, it was left set for all boards as it didn't appear to be problematic. In wider testing, I came across one reks board for which it caused FSP memory init to fail, so restricting the parameter to cyan only as it was originally. TEST: build/boot google/reks with Micron EDF8132A3MA-JD-F RAM, observe board now successfully boots where it did not previously. Change-Id: Iacfbd4bc89fa04717baf85704181d346bca2ed2f Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/22782 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-09soc/intel/cannonlake: Clean up UART codeAamir Bohra
Clean up and move UART related code under a single uart.c file. Change-Id: I7eea910e065242689e87adac41281131674b39af Signed-off-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-on: https://review.coreboot.org/22771 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Subrata Banik <subrata.banik@intel.com>
2017-12-09Update vboot submodule to upstream masterMarc Jones
Updating from commit id 3b80572: 2017-10-12 16:35:30 -0700 - (tlcl, tpmc: extend GetVersion to report vendor specific data) to commit id f6780a3: 2017-12-01 14:54:40 -0800 - (firmware: header tweaks for depthcharge) This brings in 19 new commits. Change-Id: I49b1349cfd9266cd815b68759ae89bdffdd0d74b Signed-off-by: Marc Jones <marcj303@gmail.com> Reviewed-on: https://review.coreboot.org/22777 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-09mainboard/google/kahlee: Update GPIOsMartin Roth
- The touchscreen interrupt was moved from the GPIO 3, as originally suggested to GPIO 11. This changes the gevent from 2 to 18. - Add EMMC reset on GPIO 93. - Add EMMC bridge PCIe reset on GPIO 40. - Set device enables to high. - Remove extra SCI comment from GPIO 130. - Set individual device PCIe reset pins to high. - Enable global PCIe reset on GPIO 26. - Mark LPC_CLK1 as unused. - Update net names based on latest schematics. - Set Direction and level/edge correctly for SCIs/SMIs. - Remove SCI for pen detect. - Add comments. BUG=b:70234300, b:69681660, b:69305596 TEST=build grunt Change-Id: Ib591e4278ed23d0963ecb19ad9c326498b4c7796 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/22751 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-09mainboard/google/kahlee: Update PCIe port mapMartin Roth
- Grunt moved the EMMC chip to port 2, where Kahlee had the SD reader on PCIe port 1, so move the OemCustomize file into the variant directory. - Add comments in baseboard version so it's easier to understand. - Update reset pins, put the definitions in gpio.h BUG=b:70255003 TEST=Build and boot Kahlee. Build Grunt. Change-Id: I78ec72e9d6fd52b8ac75e7187bd01ee7ddc3ba2a Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/22750 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
2017-12-08src/mainboard/glkrvp: Turn on CPU fanSrinidhi Kaushik
On GLK EC does not support temperature reads and does not control the fans anymore, OS is responsible fan control through EC. This hack enables running of the fan for boards without External EC. Change-Id: I361e53d4fd53678f3abb8fe9862071aec6e149a7 Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com> Reviewed-on: https://review.coreboot.org/22235 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
2017-12-08vendorcode/intel/fsp/fsp2_0/glk: Update header files as per v69_51Ravi Sarawadi
Update FSP header files to match FSP v69_51. UPD updates in FSP v69_51 are: - SGX Epoch - Sub/System Vendor ID - Remove deprecated UPD Change-Id: I7298615a6e051061b948814a1cd9cbd42f6574b5 Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com> Reviewed-on: https://review.coreboot.org/22391 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-12-08mb/intel/glkrvp: Fix CLKRUN gpioShaunak Saha
This patch does not put CLKRUN in IOSTANDBY. Change-Id: I7fedd729d3bb66c2b52a63166e461f8760457721 Signed-off-by: Shaunak Saha <shaunak.saha@intel.com> Reviewed-on: https://review.coreboot.org/22292 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-12-08soc/intel/apollolake/acpi/cnvi.asl: Add _PRW for CNViHannah Williams
Add CNVi GPE in _PRW for wake on WLAN from S3 Change-Id: I682c76b9c5c524face7b540ecb185a3d7b4b2da3 Signed-off-by: Hannah Williams <hannah.williams@intel.com> Reviewed-on: https://review.coreboot.org/22639 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-08soc/intel/apollolake/acpi/pch_hda: Add _PRW for HD-AHannah Williams
Add GPE in _PRW for wake from S3 for HD-audio controller Change-Id: I6ad289be8c58e48ad0ec9d2ee0894fe16b8f2e1c Signed-off-by: Hannah Williams <hannah.williams@intel.com> Reviewed-on: https://review.coreboot.org/22637 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-08google/fizz: Set BJ max current and voltageDaisuke Nojiri
This patch makes coreboot set the max current and voltage for barrel jack adapters. BUG=b:64442692 BRANCH=none TEST=Boot Fizz. Use chgsup console command to verify the max current and voltage are set as expected. Change-Id: Ifebee09096e0935cc7d3e53920a251b0496d3c55 Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/22623 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-08chromeec: Add command to override charger limitDaisuke Nojiri
This patch adds EC_CMD_OVERRIDE_DEDICATED_CHARGER_LIMIT, which overrides the max input current and voltage when a barrel jack adapter supplies power. BUG=b:64442692 BRANCH=none TEST=Boot Fizz. Use chgsup console command to verify the max current and voltage are set as expected. Change-Id: I8c6fc54e519ce13e3db82ee2cecaa96c6eb42d8a Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/22624 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-08cr50: Make EC clear AP_OFF before hibnernateDaisuke Nojiri
This patch makes AP send EC_REBOOT_HIBERNATE_CLEAR_AP_OFF, which makes EC clear AP_OFF flag then hibernate. This is needed to make Chromebox boot when cr50 toggles the EC's reset line after TURN_UPDATE_ON command. BUG=b:69721737 BRANCH=none CQ-DEPEND=CL:802632 TEST=Verify Fizz reboot after cr50 update. Change-Id: I5f590286393ac21382cab64afdccae92d3fc14ba Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/22657 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-08cbfstool: Add '-p' option for paddingDaisuke Nojiri
This patch adds '-p' to the 'add' command. It allows the add command to specify the size of the padding added with the file being added. This is useful to reserve an extra space in case the file is too big to be relocated. BUG=b:68660966 BRANCH=none TEST=emerge-fizz coreboot && cbfstool image.bin add -n ecrw -f EC_RW.bin -p 0x10 ... Verify image.bin has extra space in the file header. Change-Id: I64bc54fd10a453b4da467bc69d9590e61b0f7ead Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/22239 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2017-12-08device/pciexp_device: Set values numerically instead of as bitmaskPatrick Georgi
As noted on linux-pci, we have a weird way to handling "value" and "scale" fields that are supposed to contain numerical values: we encode them as a bitfield. Instead define the two fields (offset and mask) and use numbers. Another issue, not fixed in this CL, is that we write hard-coded values while these fields really need to contain the max() of acceptable delays of the downstream devices. That way the controller can decide whether or not to enter a deeper power management state. It's noted as a TODO. Change-Id: I895b9fe2ee438d3958c2d787e70a84d73eaa49d2 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Found-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-on: https://review.coreboot.org/22740 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-08mb/google/reef: provide override GPIO table in coralChris Wang
Allow overriding specific GPIOs by SKU ID. Override two GPIO settings for nasher to save the power consumption when the system in S0ix. Change as below: AVS_DMIC_CLK_A1: IGNORE -> Tx1RXDCRx0. AVS_DMIC_CLK_B1: IGNORE -> Tx1RXDCRx0. BUG=b:69025557 BRANCH=master TEST=compile/verify the power consumption change from ~150mW to ~100mW on clamshell SKU and from ~200mW to ~100mW for convertible SKU. Change-Id: I9e0674f206426fddb3947273754774b310106334 Signed-off-by: Chris Wang <chriswang@ami.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/22752 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2017-12-08soc/intel/cannonlake: Add PCH ID support in bootblock/report_platform.cSubrata Banik
This patch ensures that all required information for pch/mch/igd deviceid and revision are available in single stage and makes use of local references. TEST=Build and boot cannonlake_rvp to get PCH information as below PCH: device id xxxx (rev xx) is Cannonlake-Y Premium Change-Id: I420e94043145e8a5adcf8bb51239657891915d84 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/22767 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-08soc/intel/skylake: Clean up bootblock/report_platform.cSubrata Banik
This patch ensures that all required information for pch/mch/igd deviceid and revision available in single stage and make use of local references. TEST=Build and boot soraka/eve Change-Id: I6f7f219536831210750a486ee3b3308d6f285451 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/22756 Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-08soc/intel/skylake: Remove pch_enable_dev() from SoCSubrata Banik
PCI resources MMIO space/bus master enabling is handled inside pch_dev_enable_resources() from common device code. Hence no need to have an explicit soc function to do the same. TEST=lspci from kernel console shows same pci device list without and without this patch. Change-Id: I005e486dd435e9c61ae3f5dfe3ff0e8f688d16e1 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/22755 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-08soc/amd/stoneyridge: Add RO_REGION_ONLYMarc Jones
We only need the apu firmware in the RO region when building for ChromeOS. Adding it to the RW regions is a waste of space. BUG=b:70027919 TEST=Build kahlee and use cbfstool to check for "apu/amdfw" sections. Change-Id: Ieafe4a5ec4a5e3177e4e23fcf42afa2626a0b19f Signed-off-by: Marc Jones <marcj303@gmail.com> Reviewed-on: https://review.coreboot.org/22766 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-07mainboard/intel/glkrvp: Change gpio configuration for eSPIBora Guvendik
Skip LPC related gpio configuration if eSPI config option is selected. Change-Id: I15c5f769f36a1801217b1e3650379c7b181d814f Signed-off-by: Bora Guvendik <bora.guvendik@intel.com> Reviewed-on: https://review.coreboot.org/22757 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-07buildgcc: Hide stderr output of getopt testNico Huber
Change-Id: I03c38de3a3b88d569d629be7483eb53164cf136a Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/22738 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-07libpayload: Add pci_free_dev() and some boilerplateNico Huber
Add just enough code and boilerplate to keep it compatible with future libflashrom. Change-Id: If0d46fab141da525f8f115d3f6045a8c417569eb Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/20955 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-07amd/stoneyridge: Delete early_setup.cRichard Spiegel
All preparation done, early_setup.c now useless. Delete early_setup.c, BUG=b:64033893 TEST=None. Change-Id: Ibe75a2d5cc46641e9d0af462a8a0ba5bb7a0f9c3 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/22569 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2017-12-07google/scarlet: update Kingdisplay kd097d04 timingLin Huang
With the old timing, the hblank time isn't large enough, it may cause display artifacts. So fix it. BUG=b:70160653 TEST=panel work on Scarlet rev2 board Change-Id: Ib061f5e215611d20f59e3f24cfe3c7fbc507ebed Signed-off-by: Lin Huang <hl@rock-chips.com> Reviewed-on: https://review.coreboot.org/22746 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2017-12-07payloads/external/Makefile: Add missing dependencyNico Huber
The depthcharge .config only exists after depthcharge was built. Other possible `PAYLOAD_CONFIG` files most probably miss a rule, too. Change-Id: I8e6f79bb2bd07cbef1317f2623bbef9ca0e74880 Signed-off-by: Nico Huber <nico.huber@secunet.com> Tested-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: https://review.coreboot.org/22137 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-07asus/p2b-ls: Disable SuperI/O ACPI logical deviceKeith Hui
This logical device is disabled in OEM BIOS. Disable here to match, since its support is currently incomplete anyway. Change-Id: I5c07136ec6a14a8ee8cb68537a2663b78fc0fa20 Signed-off-by: Keith Hui <buurin@gmail.com> Reviewed-on: https://review.coreboot.org/22145 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marc Jones <marc@marcjonesconsulting.com> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-07asus/p2b: Align ACPI tables with asus/p2b-lsKeith Hui
Updates ACPI tables with work done for asus/p2b-ls, including super I/O related declarations. Change-Id: Id2420da4ab04aa5f59ac0aa237d21477a03b826e Signed-off-by: Keith Hui <buurin@gmail.com> Reviewed-on: https://review.coreboot.org/22473 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-07asus/p2b-ls: Add ACPI tablesKeith Hui
Add ACPI tables support that will be needed for soft-off and S3 resume in the future. Boot tested for soft-off. Change-Id: I28b559406bd53efc555dcbb8282dfe2bd6d1af87 Signed-off-by: Keith Hui <buurin@gmail.com> Reviewed-on: https://review.coreboot.org/21672 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-07sb/intel/i82371eb: Rework ACPI tablesKeith Hui
Rework ACPI tables based on a mix of previous work on asus/p2b, other boards in tree with better ACPI support, and OEM BIOS. To be pulled in by DSDTs of mainboards using this southbridge. Disable on-the-fly generation of mainboard _CRS node. It is not working as it should and causes runtime errors when booting Linux. This node to be included in mainboard DSDTs in followup patches. Change-Id: Idda424de7859a36e4cac168d5469f9365a6ad421 Signed-off-by: Keith Hui <buurin@gmail.com> Reviewed-on: https://review.coreboot.org/21671 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-07kahlee/ec.c: Use new wide IO functionRichard Spiegel
In preparation to deleting early_setup,c, change early_ec_init() to use new southbridge.c function sb_set_wideio_range and remove <#ifdef __PRE_RAM__>. BUG=b:64033893 TEST=Build, boot and check serial output, search for "Covered by wideIO xx", which should match earlier message "Range assigned to wide IO xx" generated within modified early_ec_init(). Change-Id: Iaea17f4f636aab6bd8b05b1b3bed53a677164e74 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/22591 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-07amd/stoneyridge/lpc.c: Use new wide IO functionsRichard Spiegel
Use the new wide IO functions from southbridge.c to simplify code in functions set_child_resource and lpc_enable_childrens_resources. BUG=b:64033893 TEST=Boot to OS, check serial output against previously recorded serial output from an image without all 5 related changes. Change-Id: I8533e8ff766df8a8261298559aace7666487826d Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/22574 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-07amd/stoneyridge: Create new wide IO functionsRichard Spiegel
Create new generic wide IO functions in southbridge.c. These new functions must be usable by kahlee/ec.c and amd/stoneyridge/lpc.c. BUG=b:64033893 TEST=Just build at this stage, full boot to OS and verify serial output at related change 14fdd03a83. Some extra outputs for testing removed when code was committed. Change-Id: Icd0841a1959f3e109b3c35fa35bb4b3c44099dc3 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/22590 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2017-12-07mb/google/poppy/variants/nami: Add support for nami boardFurquan Shaikh
This change adds variant nami derived from baseboard poppy. BUG=b:70160119 Change-Id: Ic6795d49d3e6e98a32f4af0b621e8bb463041412 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22703 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-07mb/google/poppy: Add support for DDR4 memoryFurquan Shaikh
This change updates memory SPD handling code in baseboard poppy to allow variants to define either LPDDR3 or DDR4 memory types. In addition to that, it also updates the function to print SPD info considering offsets that might be different across the two memory types. BUG=b:70188937 Change-Id: Iefad01719c62264fb0d7e987904e77647d6026c2 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22745 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-07mb/google/poppy/variants/nautilus: Fix memory paramsFurquan Shaikh
Until now, nautilus was using the DQ-DQS mappings provided by the baseboard. However, based on schematics, these values are not correct. This change adds DQ-DQS mapping tables for nautilus. BUG=b:70188533 Change-Id: Ife6ba19b8fe8873ab8cca977ca8f34a4d86e8e6e Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22706 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: shkim <sh_.kim@samsung.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-07soc/intel/apollolake: add ability to enable eSPIBora Guvendik
Add config option to enable eSPI TEST=Boot to OS Change-Id: Ib4634690fe4fdb902fc0bc074a3b66b91921ddd5 Signed-off-by: Bora Guvendik <bora.guvendik@intel.com> Reviewed-on: https://review.coreboot.org/22320 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Hannah Williams <hannah.williams@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com>
2017-12-07soc/intel/apollolake: Clean up UART codeAamir Bohra
Clean up and move UART related code under a single uart.c file. Change-Id: I9a30258ba43ee5920f585c1bd06bc25773778ec4 Signed-off-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-on: https://review.coreboot.org/22754 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Subrata Banik <subrata.banik@intel.com>
2017-12-07soc/intel/skylake: Clean up UART codeAamir Bohra
Clean up and move UART related code under a single uart.c file. Change-Id: I7ed03fc5fe79e38350d7edc70ad55d54db780fed Signed-off-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-on: https://review.coreboot.org/22753 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Subrata Banik <subrata.banik@intel.com>
2017-12-07soc/intel/cannonlake: Make use of Intel common Graphics blockSubrata Banik
TEST=Build and boot cannonlake rvp. Change-Id: Iaa1314ae3fcb4a8a3b55a314e79511f5dcba163d Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/22617 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-12-07soc/intel/apollolake: Make use of Intel common Graphics blockSubrata Banik
TEST=Build and boot reef. Change-Id: I0edd7454912201598c43e35990e470ec18a32638 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/22616 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-12-07soc/intel/skylake: Make use of Intel common Graphics blockSubrata Banik
TEST=Build and boot soraka/eve. Change-Id: I416226d0374700cea6eea602f839c3d17f1f39a6 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/22615 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-07soc/intel/common/block: Add Intel common Graphics controller supportSubrata Banik
SoC need to select specific macros to compile common graphics code. Change-Id: Idbc73854ce9fc21a8a3e3663a98e01fc94d5a5e4 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/22614 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-07intel/bd82x6x: Fix a small mistake in DIR_ROUTETobias Diedrich
The register is 16-bits wide. If the DIR_ROUTE call ordering was reversed the previous writes would get overwritten. See page 407ff on the Intel C216 datasheet, which says "Size: 16bits" with "Default: 3210h" for all DnnIR registers. This also makes sense given the register offsets: 3140h–3141h D31IR Device 31 Interrupt Route 3210h R/W [3142h would be D30IR] 3144h–3145h D29IR Device 29 Interrupt Route 3210h R/W 3146h–3147h D28IR Device 28 Interrupt Route 3210h R/W 3148h–3149h D27IR Device 27 Interrupt Route 3210h R/W 314Ch–314Dh D26IR Device 26 Interrupt Route 3210h R/W 3150h–3151h D25IR Device 25 Interrupt Route 3210h R/W [discontinuity in register addresses here] 315Ch–315Dh D22IR Device 22 Interrupt Route 3210h R/W [315Eh would be D21IR] 3160h–3161h D20IR Device 20 Interrupt Route 3210h R/W Change-Id: I970abbacbc2c59e86c1726171272b8779758e53e Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de> Reviewed-on: https://review.coreboot.org/22621 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2017-12-07intel/bd82x6x: Add missing IRQs in ACPI PIRQ link devicesTobias Diedrich
pch_pirq_init() sets all PIRQ links to route to irq 11. However in the ACPI data, on half the links irq 11 is missing. The other half is missing irq 10. This fixes a mostly cosmetic issue in the Linux messages: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 12 14 15) *11 ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 12 14 15) *11 ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 12 14 15) *11 ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 12 14 15) *11 ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15) Change-Id: I002147d702cacf54a233196932b30732f6a433b3 Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de> Reviewed-on: https://review.coreboot.org/22600 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2017-12-07mainboard/intel/glkrvp: Ignore Audio DMIC IOSSTATESathyanarayana Nujella
Audio DMIC_CLK needs to be ON in S0ix to support Wake on Voice. So, configuring GPIO_171 to be as IGNORE IOSSTATE, so that clock is ON in S0ix state. BUG=None TEST=put DUT in S0ix, verified DMIC_CLK in scope when wov capture path is ON Change-Id: I147cf3c12acb11429c6cb234e8c511f57886b6b4 Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Signed-off-by: Hannah Williams <hannah.williams@intel.com> Reviewed-on: https://review.coreboot.org/22675 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-07Revert "soc/intel/skylake: Clean up SoC ASL code."Matt DeVillier
This partially reverts commit a7b97510aeb1652fd0006c9b2d10df6568f37e2e. For the internal eMMC to be used by Windows for installation, the CARD device and _RMV methods are required. Without them, Windows does not see/show the eMMC as a valid installation target. TEST: boot google/chell with Tianocore payload and install Windows 10 to the internal eMMC drive. Change-Id: I04819ff16ab4cb0d2ea6e1c7f47179f5dacb7cfd Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/22684 Reviewed-by: Subrata Banik <subrata.banik@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-07amd/stoneyridge: Create new name/IRQ associationRichard Spiegel
Table intr_types[] is hard to maintain, and has unused spaces filled with NULL. A new table format is needed that creates strong association between the APIC register index and the associated IRQ name, is easy to maintain and has no unused space (index) to indicate that a particular register is unused while still indicating which registers are valid. Also, the string that defines the name of associated IRQ should be declared with "#define" in a header, but must be physically initiated in a source file. The "#define" must make a strong association between the used register index and the associated IRQ name. Example: #define INDEX_0X16_NAME "PerMon\t" BUG=b:69868534 TEST=Check serial output against BKDG for AMD Family 15h Models 70h-7Fh Processors definitions for Pci_Intr_Index. Also, check for new output format to confirm write_pci_int_table() is working as desired. There's no test for write_pci_cfg_irqs, as it's not being used by kahlee. Change-Id: I2dde4d016cc3228e50dcfadd2d3586a3609e608d Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/22667 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-07security/vboot: Remove unused include of vboot_nvstorage.hRandall Spangler
This include is not needed, and the header file is going away in vboot_reference. So, remove it. BUG=chromium:789276 BRANCH=none TEST=emerge-reef coreboot Change-Id: Ie0b37ae3d2f979f79060a15ca3f7157f49c89785 Signed-off-by: Randall Spangler <rspangler@chromium.org> Signed-off-by: Randall Spangler <randall@spanglers.com> Reviewed-on: https://review.coreboot.org/22733 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2017-12-07google/gru: Add SKU ID for ScarletJulius Werner
Scarlet has SKU detection strapping pins now. This patch adds the code to read them. BUG=b:69373077 Change-Id: I8d889a845950923bc7b5be9b79792cf3c8b6b8ad Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/22697 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-07rockchip/rk3399: Select GENERIC_GPIO_LIB KconfigJulius Werner
This option should've been selected by RK3399 the whole time since the SoC supports the <soc/gpio.h> interface. It wasn't really a big deal until now where I'm trying to use a the base2 read helper, though. Change-Id: Ib7a5f00a6680163105fc0598ce77d03f3645f05a Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/22744 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-07libpayload: Add SKU ID coreboot table supportJulius Werner
This patch adds support to read the SKU ID entry from the coreboot table that was recently added in coreboot. Change-Id: I1c3b375da6119a4f8e8e7e25a11644becb90f927 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/22743 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-07boardid: Add helpers to read sku_id strapping into coreboot tablesJulius Werner
On many recent Chrome OS boards, the desire to unite more configurations under the same image has led to the need of a "SKU ID" that identifies different configurations of the same board (e.g. with certain optional components stuffed or not stuffed, or replaced with a comparable component). This is markedly different from the existing "board ID", because that is reserved to count "revisions" -- changes made to the same configuration over time during the development process. This patch adds support to have a mainboard define this SKU ID and pass it through the coreboot table like we already have for board IDs. Change-Id: I8aabffe8e1003b0d6fb70d689ae513ca4b46aeda Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/22696 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-07boardid: Switch from Kconfig to weak functionsJulius Werner
This patch switches the board_id and ram_code helper framework to use weak functions rather than Kconfigs to determine whether the board supplies these IDs. This cuts down on the amount of boilerplate Kconfigs many boards have to set and also gives them more flexibility, such as being able to determine at runtime whether a given ID is present. Change-Id: I97d6d1103ebb2a2a7cf1ecfc45709c7e8c1a5cb0 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/22695 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-07libpayload: Minor board ID / RAM code cleanupsJulius Werner
This patch mirrors recent cleanups in coreboot regarding the strapping ID entries in the coreboot table. Change-Id: Ia5c3728daf2cb317f8e2bc72c6f1714d6cb4d080 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/22742 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-07boardid: Minor clean up and standardizationJulius Werner
Merge the different coreboot table strapping ID structures into one because they're really just all the same, and I want to add more. Make the signature of the board_id() function return a uint32_t because that's also what goes in the coreboot table. Add a printk to the generic code handling strapping IDs in ramstage so that not every individual mainboard implementation needs its own print. (In turn, remove one such print from fsp1_1 code because it's in the way of my next patch.) Change-Id: Ib9563edf07b623a586a4dc168fe357564c5e68b5 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/22741 Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-06Kconfig: Remove BOARD_ID_MANUAL optionJulius Werner
The BOARD_ID_MANUAL and BOARD_ID_STRING options were introduced for the Urara board which is now long dead, and have never been used anywhere else. They were trying to do something that we usually handle with a separate SKU ID these days, whereas BOARD_ID is supposed to be reserved for different revisions of the same board/SKU. Get rid of it to make further refactoring of other options easier. Also shove some stuff back into the Urara mainboard that should've never crept into generic headers. Change-Id: I4e7018066eadb38bced96d8eca2ffd4f0dd17110 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/22694 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-06mb/*/*/Kconfig: Remove default MMCONF_BASE_ADDRESS on Sandy BridgeArthur Heymans
Change-Id: I6f0d6d7fefc77fb05cdb629d09de8cb72496a9cc Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/22664 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2017-12-06mb/google/poppy: Remove variant_cros_gpios from variantsFurquan Shaikh
Variants nautilus and soraka currently provide the exact same definition for variant_cros_gpios as provided by the baseboard. This change removes the function defintions from variants so that the weak definition in baseboard can be used. Change-Id: Ic88623f34039792f0f9fb46842b24e4f1290981b Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22705 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-06mb/google/poppy: Add config option for camera ACPI supportFurquan Shaikh
This change adds a new config option VARIANT_HAS_CAMERA_ACPI to allow variants to define ACPI tables for camera support. It also prevents boards that do not need this from unnecessarily providing dummy files for camera ACPI support. Change-Id: I91f8e407e0f021071eeadbde8c2695e2a6d69e06 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22702 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-06mb/google/poppy: Change POPPY_USE_* to VARIANT_HAS_*Furquan Shaikh
Change the prefix for TPM options from POPPY_USE_* to VARIANT_HAS_*. This makes it clear that these are variant specific options. Change-Id: I6fd120a34a5b0c1f018164d5c2b60548da1d0f61 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22701 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-06mb/google/poppy: Introduce VARIANT_SPECIFIC_OPTIONS_*Furquan Shaikh
In order to allow variants to select different Kconfig options, this change adds VARIANT_SPECIFIC_OPTIONS_${VARIANT_NAME} which can be selected by each variant in Kcnonfig.name. Change-Id: I15db2fdac5c9e55f9698c8a0c083d6467afae245 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22700 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-06mb/google/poppy: Remove dynamic disabling of TPMFurquan Shaikh
This change removes the dynamic disabling of TPM based on config options. Poppy and its variants will have only one type of TPM supported and so there is no need to update it dynamically. Change-Id: Ie82825fcf7092e845583edaac9ba0d3fc9d1dd80 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22704 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-12-06mb/google/poppy/variants/soraka: Disable SPI TPMFurquan Shaikh
Soraka is no longer using SPI TPM. This change disables GSPI0 in device tree and updates gpio config accordingly. Change-Id: Ia0554ce3a0d553631123cc2b23b6dc2f6f40a1a3 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22699 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-06mb/google/poppy: Disable SPI TPMFurquan Shaikh
Mainboard poppy is no longer using SPI TPM. This change disables GSPI0 in device tree and udpates gpio configuration accordingly. Change-Id: I713e41c45e323bf13aa79412ec679c90121a52b2 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22698 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-06google/kahlee: Set USB OC pinsMarc Jones
Set the USB over current pins for the Grunt baseboard and Kahlee mainboard. Removes the ACPI ASL OC code, which is not used on Stoney Ridge SOC. BUG=b:69229635 TEST=Build and boot Kahlee. Not tested with OC test fixture. Change-Id: I5a9b3409d9c91b89fd02f8eecf9e04c435f14342 Signed-off-by: Marc Jones <marcj303@gmail.com> Reviewed-on: https://review.coreboot.org/22679 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2017-12-06soc/amd/stoneyridge: Add USB OC supportMarc Jones
Add USB overcurrent support. Adds a weak call for mainboards that don't suport USB OC. BUG=b:69229635 Change-Id: Ie54c7a2baa78f21cf1cd30d5ed70c8c832cf3674 Signed-off-by: Marc Jones <marcj303@gmail.com> Reviewed-on: https://review.coreboot.org/22678 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2017-12-06soc/amd/stoneyridge: Add XHCI PM register access functionsMarc Jones
Add functions to access the XHCI PM MMIO registers. Change-Id: I81b4c0a448eb17c5ee0562a2c3548a074d533a98 Signed-off-by: Marc Jones <marcj303@gmail.com> Reviewed-on: https://review.coreboot.org/22677 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2017-12-05google/gru: update RAMID tableLin Huang
There is some confusion with old RAMID table, make it clear, and let's no longer tangle it in future. Change-Id: I44215b4a6668074575a5df691ac1ff8fa3d15492 Signed-off-by: Lin Huang <hl@rock-chips.com> Reviewed-on: https://review.coreboot.org/22663 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2017-12-05soc/intel/cannonlake: Fix DSX_CFG macro name for AC_PRESENTFurquan Shaikh
DSX_CFG provides a config option to disable internal pull-down on AC_PRESENT. This change updates macro name to reflect this correctly. Change-Id: I620d7da4048178f86de41f3afd98543cf8efc5ce Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22690 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-05mb/google/poppy,nautilus,soraka: Disable PD on AC_PRESENT in deep SxFurquan Shaikh
This change updates device tree deep_sx_config to disable internal pull-down on AC_PRESENT. BUG=b:69983729 Change-Id: I041900a5262f8fd920856f126185329242a0639a Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22689 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-05soc/intel/skylake: Fix DSX_CFG macro name for AC_PRESENTFurquan Shaikh
DSX_CFG provides a config option to disable internal pull-down on AC_PRESENT. This change updates macro name to reflect this correctly. BUG=b:69983729 Change-Id: I291112858c4ce36667edf30fe303fed437baf5d2 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/22688 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-12-05lint-stable: Only check files tracked by git (ie source files) for +xPatrick Georgi
Change-Id: I99cbcba7a086ef950f248888a83cf24a4db4aee9 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/21419 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 12:05:13 +0000