summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-12-20armv7: Remove SYS_TEXT_BASE config.Hung-Te Lin
SYS_TEXT_BASE is not used by any one. To prevent confusion when changing memory layout, remove it from current configurations. Change-Id: I15012b864bbb9c12003843b9b24ea64c91f4578b Reviewed-on: https://gerrit.chromium.org/gerrit/61853 Reviewed-by: David Hendricks <dhendrix@chromium.org> Commit-Queue: Hung-Te Lin <hungte@chromium.org> Tested-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: http://review.coreboot.org/4371 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-12-20abuild: improve --removePatrick Georgi
Make abuild -r work in more sitations (eg. xargs parallelization), and make it not break junit output. Also tell Kconfig to just overwrite the config file, instead of atomically updating it, which help if coreboot-builds is on a different filesystem (eg. tmpfs). Change-Id: I2f4eedfd34ea6771732a60b38f1856056089be23 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/4542 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-19ec/lenovo/h8: Enable 3G modemVladimir Serbinenko
Just like bluetooth and wlan it need to be enabled in EC. Set the appropriate bit in EC if CMOS config says so. Change-Id: Ia48ca3201f013d3b4c4153f32ff536e06b6a2f6d Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/4516 Tested-by: build bot (Jenkins) Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-18lynxpoint: Don't write to non-existent EHCIDuncan Laurie
The LynxPoint-LP chipset only has one EHCI controller so we should not attempt to write into the second one that only exists on LynxPoint-H. Change-Id: I1eae060c7f0a5873c9684e5abfeea5cb5895ab62 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/63799 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4405 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-17cpu/intel: Do not rely on CBFS microcode having a terminatorAlexandru Gagniuc
Up until now, a dummy terminator was required for CBFS microcode files. This was a coreboot only requirement in order to terminate the loop which searches for updates. Figure out where the microcode file ends, and exit the loop if we pass the end of the CBFS without finding any updates. Change-Id: Ib61247e83ae6b67b27fcd61bd40241d4cd7bd246 Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/4505 Tested-by: build bot (Jenkins) Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-12-17device/dram/ddr3: Move CRC calculation in a separate functionAlexandru Gagniuc
Calculating the CRC of a SPD may be useful by itself, so split that part of the code in a separate function. Change-Id: I6c20d3db380551865126fd890e89de6b06359207 Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/4537 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-16X60/T60: Implement "next display output" button.Vladimir Serbinenko
Most of the code needed for this is already in the tree with X201 patch series but code didn't know where to send the next screen notification and so was disabled. Define right video device. Tested by: Sam Noble Change-Id: I4ff0d220afdca342617ce43c6e5d0164ad8eba27 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/4494 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2013-12-16qemu/videoinit: Set required fields in fake EDIDVladimir Serbinenko
x_resolution, y_resolution and bytes_per_line were not inited. Without them coreboot sweared that screen is 1108630x1142817 and payload tried to draw on such a big screen. Change-Id: I0d0277a20c7e1976c27af4a57651ab2be0f9c5d7 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/4535 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-16libpayload: Add simple hexdump functionRonald G. Minnich
- prints hex and ascii - detects duplicate all zero lines Change-Id: I084b3072bc05725b23c5c3ca0dbf1533f164a08c Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/63660 Reviewed-by: David Hendricks <dhendrix@chromium.org> Commit-Queue: Stefan Reinauer <reinauer@chromium.org> Signed-off-by: Ronald G. Minnich <rminnich@gmail.com> Author: Ronald G. Minnich <rminnich@gmail.com> Reviewed-on: http://review.coreboot.org/4393 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2013-12-15lenovo/x201: Add support for Lenovo X201 (Calpella-based laptop)Vladimir Serbinenko
Was extensively tested on my X201. More info on the wiki Change-Id: I503d77749780422e446b48224ca98a1f22a2c180 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/4514 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-15ec/lenovo/h8: Fix peripheral init without CMOS configVladimir Serbinenko
Currently H8 skips important init if unable to access CMOS config. Change default to enable all features to have a sane system without using CMOS config. Change-Id: I4448ccd21beae8ad23eb22391770c6fe3b83e3b4 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/4515 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2013-12-15intel/cougar_canyon2/Kconfig: Remove HAVE_ACPI_RESUME as S3 is unsupportedPaul Menzel
According to the commit message for the board Cougar Canyon 2 (48a749a8) resuming from S3 is currently unsupported. The FSP does not support S3 at this time. S3 may be added when it is available in the FSP. Mirror that in the configuration by not selecting the Kconfig option `HAVE_ACPI_RESUME`. Change-Id: I894f103ffa7d8db6342f99fff0867b02bc750752 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/4519 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-12-14drivers/pc80: Add ACPI description.Vladimir Serbinenko
AT controller needs an ACPI node, otherwise FreeBSD doesn't detect keyboard and mouse. Currently each SuperIO adds its own description. This one should be used in the future instead. Change-Id: Iaad5ed3846c6d9f467a02a286a1e6f60a3607af5 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/4518 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-12-13cpu/amd: Remove error messages on non-matching microcode patchesKyösti Mälkki
Microcode update file contains patches for various processor revisions, it is not an error to have those. Change-Id: Ifbca26276b66f17092afe249a2cfc229713a9fec Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/4520 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-13crossgcc: Fix a typo.Zheng Bao
Change-Id: I8b88957a93e6369c59e9eb17f4ba48954fbc3c02 Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/4526 Tested-by: build bot (Jenkins)
2013-12-13cpu: Rename CPU_MICROCODE_IN_CBFS to SUPPORT_CPU_UCODE_IN_CBFSAlexandru Gagniuc
CPU_MICROCODE_IN_CBFS was designed to mean that loading microcode updates from a CBFS file is supported, however, the name implies that microcode is present in CBFS. This has recently caused confusion both with contributions from Google, as well as SAGE. Rename this option to SUPPORT_CPU_UCODE_IN_CBFS in order to make it clearer that what is meant is "hey, the code we have for this CPU supports loading microcode updates from CBFS", and prevent further confusion. Change-Id: I394555f690b5ab4cac6fbd3ddbcb740ab1138339 Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/4482 Reviewed-by: Marc Jones <marc.jones@se-eng.com> Tested-by: build bot (Jenkins)
2013-12-12libpayload: expose cbfs ram functionsAaron Durbin
The ram_media.c file is being compiled, however the global functions were not exposed through a header. Change-Id: I4588fbe320c29051566cef277bf4d20a83abf853 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/56642 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/4194 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12EDID: add fields specialized to the needs of framebuffersRonald G. Minnich
Now that we have horizontal display areas that are not multiples of 32 bytes, things are more complex. We add three struct members (x, y resolution and bytes per line) which are to be filled in by the mainboard as it sets the mode. In future, the EDID code may take a stab at initializing these but the values are context-dependent. Change-Id: Ib9102d6bbf8c66931f5adb1029a04b881a982cfe Signed-off-by: Ronald G. Minnich <rminnich@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/60514 Tested-by: Ronald G. Minnich <rminnich@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Commit-Queue: Ronald G. Minnich <rminnich@chromium.org> Reviewed-on: http://review.coreboot.org/4336 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12bolt: Initial mainboard commitDuncan Laurie
BUG=chrome-os-partner:20448 BRANCH=none TEST=emerge-bolt chromeos-coreboot-bolt Change-Id: I634a755ac7659e7a977b51bcc061f69eb8263810 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/59843 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4330 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12HDA: Enable Mini-HDA and fix up PCH-HDA initDuncan Laurie
The SystemAgent contains a mini-hd audio controller at PCI 0:3.0 which uses the same verb table init sequence as the southbridge. In order to avoid two copies of the verb table loading code I separated out the HDA verb table functions into a file that can be re-used and then added a minihd driver to the haswell northbridge. The minihd verb table is the same across devices so it can live within the minihd driver rather than needing to be specified in each separate mainboard. I also fixed up the driver for lynxpoint HDA by following the reference code. Without HDMI cable plugged in driver does not find any codec, and it does not seem to re-probe when HDMI is connected. We may be missing kernel patches for this. hda-intel 0000:00:03.0: no codecs found! With a basic kernel patch to add 0x0a0c device ID to HDA driver and with HDMI cable connected it is much happier: snd_hda_intel 0000:00:03.0: irq 60 for MSI/MSI-X input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input9 snd_hda_intel 0000:00:1b.0: irq 61 for MSI/MSI-X input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input10 input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input11 Change-Id: Ifa587984be4fc2801704a0368b9cdf8379c2450e Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/59336 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4318 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12slippy/falco/peppy: make GPIO interrupts be edge triggeredDuncan Laurie
The drivers are designed to work with an edge triggered interrupt. Change-Id: I35a121ecfb6409bb9049f4d1e034185bb3bb7557 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/61664 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4360 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12EXYNOS5250: be less chatty at critical momentsRonald G. Minnich
The 5250 DRAM code is *really* chatty. That's not a great idea in time critical code, and DRAM init is generally very sensitive about such things. Finally, for those things that are errors, print them at an error level, not a debug level. Change-Id: Ifa86b019dfd5f8ae6c8a1da2a35b5d0808dc3623 Signed-off-by: Ronald G. Minnich <rminnich@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/60100 Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Commit-Queue: Ronald G. Minnich <rminnich@chromium.org> Tested-by: Ronald G. Minnich <rminnich@chromium.org> Reviewed-on: http://review.coreboot.org/4359 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12falco: drive WLAN_DISABLE_L low in S3 and S5Aaron Durbin
When the board is in S3 and S5 the WLAN_DISABLE_L signal can leak power into the WLAN power well since the GPIO controlling WLAN_DISABLE_L is in the suspend well. Therefore, drive WLAN_DISABLE_L low to avoid the power leak. Change-Id: I1a0df80dd47fdbd535aca7a9d49253794c480606 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/61421 Reviewed-on: http://review.coreboot.org/4358 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-12-12exynos5250: Correct DDR3 Phy-reset value names.Hung-Te Lin
The name "LPDDR3PHY_CTRL_PHY_RESET_OFF" is not appropriate because the real phy-reset is a low-active pin, so "off(0)" will trigger "start to reset". To prevent confusion, we should rename the constants to "RESET_ENABLE" and "RESET_DISABLE". Change-Id: Iccba5ef3a2e992f877dea90741f0308c161758c9 Reviewed-on: https://gerrit.chromium.org/gerrit/61081 Tested-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: David Hendricks <dhendrix@chromium.org> Commit-Queue: Hung-Te Lin <hungte@chromium.org> Reviewed-on: http://review.coreboot.org/4357 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12haswell: Fix up GPU power management setupDuncan Laurie
New/more magic values from latest ref code. Change-Id: Ia2655333b4daca86c2f2a76f5edcd55cdaf3f851 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/61334 Commit-Queue: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4356 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12haswell: Export functions for CPU family+model and steppingDuncan Laurie
These are needed to enable workarounds/features on specific CPU types and stepping. The older northbridge function and defines from sandybridge/ivybridge are removed. Change-Id: I80370f53590a5caa914ec8cf0095c3177a8b5c89 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/61333 Commit-Queue: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4355 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12exynos5420: Setup clocks for MMC bus controller.Hung-Te Lin
To configure source clocks on Exynos 5420 for MMC drivers. Some registers are different from the 5250. FSYS now has two parts and MMC uses FSYS2. The MMC block uses MPLL as the clock source. The "high-speed" MMC interface runs as 52MHz, so divider is set accordingly. Also, the MMC driver has changed from MSHCI (Mobile Storage Host Controller Interface) to DWMCI (DesignWare MMC Controller Interface). Change-Id: I9ba9cf43e2f2dcd9da747888c0c7676bd545177b Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/60858 Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/4354 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12peppy: Add backward-compatible RAM_ID table.Shawn Nematbakhsh
Make use of google_chromeec_get_board_version to determine board version, and apply proper RAM_ID table to load correct SPD. Change-Id: I6a2d54759cf2ce98bf53df0db396c6e09368c714 Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/61192 Reviewed-by: Dave Parker <dparker@chromium.org> Reviewed-on: http://review.coreboot.org/4353 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12Peppy: Update Realtek ALC283 verb tableMartin Roth
Update peppy's verb tables for the Realtek ALC283 Audio Codec. ALC283 Configuration: Digital Mic - NID 12h: Disabled Speakers - NID 14h: Enabled Mono out - NID 17h: Disabled Mic 1 - NID 18h: Disabled Mic 2 - NID 19h: Headphone Jack Line1 - NID 1Ah: Internal Mic Line2 - NID 1Bh: Disabled PCBEEP - NID 1Dh: Enabled SPDIF - NID 1Eh: Disabled HP-OUT - NID 21h: Headphone Jack Mic 1 doesn't seem to really be available, but the documentation refers to NID 18h as MIC1, so it's being disabled as it's not being used. The onboard microphone has been moved to line 1. I had my peppy modified to attach the mic to line1 and mic1 now works with this patch. Mic2 looks harder to rework, so I think that will have to wait for the DVT boards. Change-Id: I7d6ce6b428806b6aed1d36e7e25302fa5ae14b21 Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: https://gerrit.chromium.org/gerrit/58880 Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: http://review.coreboot.org/4352 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-12-12chromeec: Allow get_board_version to be called from romstage.Shawn Nematbakhsh
We will soon need to call google_chromeec_get_board_version to determine correct DDR SPD. We must do so before DDR is initialized, so allow this function to be called from romstage. Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Change-Id: I882d84e38d11bf66067193a6f408f941f2cf8a81 Reviewed-on: https://gerrit.chromium.org/gerrit/61191 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: Shawn Nematbakhsh <shawnn@chromium.org> Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: http://review.coreboot.org/4351 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12falco: fix usb port settingsDuncan Laurie
USB2 Port A set to 6.4" and Back Panel USB2 Port B set to 5.2" and Back Panel USB2 Port C set to 12.3" and Internal Other devices all set to Internal. build and boot on falco and check settings. Based on the config settings all ports end up with tuning param 1 == 5 and param 2 == 2 U2ECR[0] = 0x00059501 U2ECR[1] = 0x00059501 U2ECR[2] = 0x00059501 U2ECR[3] = 0x00059501 U2ECR[4] = 0x00059501 U2ECR[5] = 0x00059501 U2ECR[6] = 0x00059501 U2ECR[7] = 0x00059e01 Change-Id: I6b9e6df2679036a501355e6b389a486a6f178f99 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/61297 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4350 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-12-12Log device path during resource allocationDuncan Laurie
Systems are hanging in dev_configure() without a log to indicate which device is being processed. Add some logging points to save the device path before talking to the device so we can narrow in on which device is the problem. Change-Id: I3751c19a1ea68cdccbc33e4f6b2eeddd1bd9f2e4 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/61296 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4349 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-12-12haswell: Update ULT microcode to rev 14hDuncan Laurie
localhost ~ # grep ^microcode /proc/cpuinfo microcode : 0x14 microcode : 0x14 Change-Id: I839f29cff61abf798a619b30ad945e25c79f548f Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/60658 Reviewed-on: http://review.coreboot.org/4348 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12falco: Remove thermal thresholds that use CTDPDuncan Laurie
This CPU does not support Configurable TDP and so far does not need to use Controllable TDP. Change-Id: I15599cd4e6890dd5c9d9f99bc4e95307a8dcc827 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/60657 Reviewed-on: http://review.coreboot.org/4347 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12libpayload: Get rid of a compiler warningGabe Black
Change-Id: I7252925ef5c4efb69cad6b6fa179031162cf8e74 Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/61058 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Commit-Queue: Gabe Black <gabeblack@chromium.org> Tested-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/4346 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12libpayload: armv7: Add cache control function to invalidate range.Hung-Te Lin
When dealing with DMA, we need a function to invalidate cache without corrupting contents on main memory (clean). Change-Id: I28e632ae57a7b7ed1accee74e76045b92f92a699 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/61078 Reviewed-by: Gabe Black <gabeblack@chromium.org> Commit-Queue: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/4345 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12payload: armv7: Fix dcache_clean_by_mva.Hung-Te Lin
The OP assigned by dcache_clean_by_mva must be handled in dcache_op_mva. Change-Id: Ib32262f0419453b2690d7c1a1c6602380b46a37f Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/61077 Reviewed-by: Gabe Black <gabeblack@chromium.org> Commit-Queue: Gabe Black <gabeblack@chromium.org> Tested-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/4344 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12armv7: Fix dcache_clean_by_mva.Hung-Te Lin
The OP assigned by dcache_clean_by_mva must be handled in dcache_op_mva. Change-Id: Ia7631a08be6afacb13dfff406ac4db20efc98926 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/61076 Reviewed-by: Gabe Black <gabeblack@chromium.org> Commit-Queue: Gabe Black <gabeblack@chromium.org> Tested-by: Gabe Black <gabeblack@chromium.org> Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/4343 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12PIT: remove a comment that is incorrect.Ronald G. Minnich
The is_resume comment is wrong for this board. It only applies to the older 5250 cpu. In fact, the is_resume parameter is not needed for ddr init and will likely be removed soon. Change-Id: I4e3c92fcaaa75d3c9223d90acccf053f61406307 Signed-off-by: Ronald G. Minnich <rminnich@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/60103 Reviewed-by: David Hendricks <dhendrix@chromium.org> Commit-Queue: Ronald G. Minnich <rminnich@chromium.org> Tested-by: Ronald G. Minnich <rminnich@chromium.org> Reviewed-on: http://review.coreboot.org/4342 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12snow: Fix the edid data structure definition so depthcharge works again.Gabe Black
Some new fields were added to the edid data structure, and the edid code was changed to put estimated values into those fields which were ultimately passed into depthcharge or other payloads. On snow we do things different and just declare an edid structure statically which didn't have those members. The rows and columns of the graphics console were 0, and that confused the framebuffer driver and made it loop forever. Change-Id: I6ca3bd948482b347a6a981e83b82b10dca995e5e Signed-off-by: Gabe Black <gabeblack@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/61057 Reviewed-by: Ronald G. Minnich <rminnich@chromium.org> Commit-Queue: Gabe Black <gabeblack@chromium.org> Tested-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/4341 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12peppy: RAM_ID + storage changes for next build.Shawn Nematbakhsh
- Update RAM_ID table. - Add DEVSLP0 signal to NGFF SATA port. Note: After this change, old Micron 2GB boards will no longer boot. Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Change-Id: Id68a1d6ace2702cca9c37305726cd55a0bde5005 Reviewed-on: https://gerrit.chromium.org/gerrit/60167 Tested-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-by: Dave Parker <dparker@chromium.org> Commit-Queue: Dave Parker <dparker@chromium.org> Reviewed-on: http://review.coreboot.org/4340 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12peppy: Disable audio codec enable GPIO in S3 + S5.Shawn Nematbakhsh
To save power, disable audio codec in S3 + S5. Also, refactor Lynxpoint GPIO code slightly to allow usage in SMM binary. Change-Id: I55c4248c89a258b5e4cecf8579eb58f1c15430c0 Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/60950 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4339 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-12board-status: extend wiki forewordPatrick Georgi
Change-Id: I9791beff44535a0a130292414fcd9875b497b1ca Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/4492 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-09AMD boards: Fix includes for microcode updatesKyösti Mälkki
No ROMCC involved, no need to include .c files in romstage.c. Change-Id: I8a2aaf84276f2931d0a0557ba29e359fa06e2fba Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/4501 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-12-09Refactor usage of walkcbfs to permit access to CBFS headersAlexandru Gagniuc
walkcbfs() is used only with ROMCC. Besides finding stages during the bootblock, it's also used when applying microcode updates during the bootblock phase. The function used to return only a pointer to the data of the CBFS file, while making the header completely inaccessible. Since the header contains the length of the CBFS file, the caller did not have a way to know how long the data was. Then, other conventions had to be used to determine the EOF, which might present problems if the user replaces the CBFS file. This is not an issue when jumping to a stage (romstage), but can present problems when accessing a microcode file which has not been NULL-terminated. Refactor walkcbfs_asm to return a pointer to the CBFS file header rather than the data. Rename walkcbfs() to walkcbfs_head(), and reimplement a new walkcbfs() based on walkcbfs_head(). Thus current usage of walkcbfs() remains unaffected. The code has been verified to run successfully under qemu. Subsequent patches will change usage of walkcbfs() to walkcbfs_head where knowing the length of the data is needed. Change-Id: I21cbf19e130e1480e2749754e5d5130d36036f8e Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/4504 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-12-09cbfstool: Properly handle EOF in update_fit stepAlexandru Gagniuc
During the update_fit step, 'file_length' is used to determine how many bytes are left in the CBFS file. It was decremented in a loop from an array 'mcus[num_mcus].size', but 'num_mcus' was incremented right before. Since 'mcus' is memset(0) externally, 'file_length' was never decremented. The loop exited when it reached a dummy terminator, usually 48 bytes of 0 which are internationally added to microcode blobs in coreboot. However, if that terminator is removed, the loop doesn't stop and continues until it segfaults. Change-Id: I840727add69379ffef75b694d90402ed89769e3b Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/4508 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-12-09crossgcc: Continue to unpack archive if it was incompleteZheng Bao
If the unpacking was interrupt by Ctrl-C, probably part of an archive is unpacked. If we run buildgcc again, the incomplete folder would be and skipped. We can create a file to tell the script the unpacking is done. Change-Id: Id9eb74d119e22b62c70dca9b38a92c3dbdf0f64c Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/4512 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-12-09gitignore: ignore the crossgcc/build-{arch}-{archive}Zheng Bao
The architecture information has been added to the folders to build archives for crossgcc. We need to change the .gitignore to keep ignoring them. Change-Id: Ic18685e507f1b09088120eee6047d49141e29906 Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/4513 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-12-09documentation: Change the file name of document for building CorebootZheng Bao
I am planning to write a document for new man, helping them to build a working image from knowing nothing about Coreboot. The previous LinuxBIOS-AMD64.tex was a good script. LinuxBIOS was a out-of-date name. It needs to be changed it to Coreboot. And the new document is not specific to AMD, so we get rid of the AMD64 from the file name. This is a separate patch for the renaming. LinuxBIOS-AMD64.tex was still about SVN and buildtarget. Later patch will come up for updating those old thing. And this new document, CorebootBuildingGuide.tex, is planning to be only about building. Navigating the source code is moved to later advanced document. Change-Id: Ia8a2fd9db51e9870c1d645067bcfdc91ae1bf90a Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/4487 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-12-07board-status: update forewordPatrick Georgi
Change-Id: I6acafee948b1224b88fd640e02c18168c1f90e39 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/4496 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2013-12-07board-status: one-line reports, with links to per-board pagesPatrick Georgi
Make boards take less vertical space, and link to board pages Change-Id: Ifdd062a15191809b75422416c874161d9114363d Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/4493 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-07snprintf: lockless operationVladimir Serbinenko
Instead of having global variables put them on the stack. Change-Id: I462e3b245612ff2dfb077da1cbcc5ac88f8b8e48 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/4288 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Tested-by: build bot (Jenkins)
2013-12-07vtxprintf: Introduce vtxdprintf for the ease of closuresVladimir Serbinenko
It was suggested to eliminate the lock for sprintf. One way to do it is to make the fake tx_byte into a closure. This patch allows it. It's a bit tricky since we need to preserve compatibility with romcc. Change-Id: I877ef0cef54dcbb0589fe858c485f76f3dd27ece Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/4287 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-12-07board-status: document the wiki scriptsPatrick Georgi
These were terribly under-documented Change-Id: I285ea083110d87076281e81065f5f38d0c688358 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/4491 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-07haswell: VR controller configurationAaron Durbin
Configure the VR controller. This enables the PSIx levels as well as C-state ramping. PSIx thresholds are: - PSI3: 1A. - PSI2: 5A. - PSI1: 15A. Before: 0x601 0x0000000000000100 0x603 0x0036000000262626 0x636 0x000000000000006f After: 0x601 0x4010140f00000100 0x603 0x0036000000262626 0x636 0x000000000000006f Change-Id: I6958845ac4164ebd0f1bb2d6d9be55ba63ed9344 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/60931 Reviewed-by: Sameer Nanda <snanda@chromium.org> Reviewed-on: http://review.coreboot.org/4338 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2013-12-07Add kernel-derived support functions for DDI.Ronald G. Minnich
Newer mainboards that use haswell -- and, presumably, chipsets to come -- need some support functions. Add them in the drivers/intel/gma directory. Currently, this is one file: intel_ddi.c, but more may come. Compilation of this file is controlled by INTEL_DDI, defined in the Kconfig as default n and used in the Makefile.inc Change-Id: I501ee291c0d4589925ed3e478f67106337fcad31 Signed-off-by: Ronald G. Minnich <rminnich@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/60612 Tested-by: Ronald G. Minnich <rminnich@chromium.org> Reviewed-by: Ronald G. Minnich <rminnich@chromium.org> Commit-Queue: Ronald G. Minnich <rminnich@chromium.org> Reviewed-on: http://review.coreboot.org/4337 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-07abuild: drop xml modePatrick Georgi
We use junit style output these days. Change-Id: I4110ec10bf0e9f4354ee08e7e1c5a81ae605fee0 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/4484 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-12-07haswell: Add ACPI support for Controllable TDPDuncan Laurie
Add ACPI Methods to enable and disable power limiting with PL1. This can be used in ACPI Thermal Zone or in EC ACPI _QXX events. This commit adds new unused methods and is fully tested with the subsequent commit that makes use of these methods. Change-Id: I9d8d23bfe9cf7c756ff8ab0412e5a010826b12db Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/60546 Reviewed-on: http://review.coreboot.org/4334 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2013-12-07haswell: Misc power management setup and fixesDuncan Laurie
1) fix enable of power aware interrupt routing 2) set BIOS_RESET_CPL to 3 instead of 1 3) mirror PKG power limit values from MSR to MMIO on all SKUs 4) mirror DDR power limit values from MMIO to MSR 5) remove DMI settings that were from snb/ivb as they do not apply to haswell 1) verify power aware interrupt routing is working by looking in /proc/interrupts to see interrupts routed to both cores instead of always to core0 BEFORE: 58: 4943 0 PCI-MSI-edge ahci AFTER: 58: 4766 334 PCI-MSI-edge ahci 2) read back BIOS_RESET_CPL to verify it is == 3 localhost ~ # iotools mmio_read32 0xfed15da8 0x00000003 3) read PKG power limit from MMIO and verify it is the same as the MSR value localhost ~ # rdmsr 0 0x610 0x0000809600dc8078 localhost ~ # iotools mmio_read32 0xfed159a0 0x00dc8078 localhost ~ # iotools mmio_read32 0xfed159a4 0x00008096 4) read DDR power limit from MSR and verify it is the same as the MMIO value (note this is zero based on current MRC input) localhost ~ # rdmsr 0 0x618 0x0000000000000000 localhost ~ # iotools mmio_read32 0xfed158e0 0x00000000 localhost ~ # iotools mmio_read32 0xfed158e4 0x00000000 Change-Id: I6cc4c5b2a81304e9deaad8cffcaf604ebad60b29 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/60544 Reviewed-on: http://review.coreboot.org/4333 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2013-12-07peppy: Enable power limiting for thermal controlDuncan Laurie
Limit power to 12W at 73C and remove limit at 68C. To have the CPU consume maximum power it is necessary to stress both the CPU and the GPU. Bastion (chrome.supergiantgames.com) and/or webglsamples.googlecode.com can be useful for this. Testing this properly requires a script to report the running average power readings. The watch_power.sh script is attached to this issue in the partner tracker. 1) Run watch_power.sh continuously: localhost ~ # watch -n 0 bash -e /tmp/watch_power.sh 2) Start Bastion (or other stress apps). The power draw should be close to 15W if under enough load. 3) Watch until temperature climbs above 73C and is caught by the thermal zone 10 second poll, this can be sped up by blocking or removing the fan. 4) The ACPI thermal zone states should change to reflect that active[2] is now enabled and power consumption should drop to 12W. 5) Stop the stress apps and wait until the CPU cools off again, enable the fan again if it was removed. 6) The ACPI thermal zone state should switch back to active[3]. Change-Id: Ie6714a8543d4f06edf8513086fc9c968273bdb23 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/60545 Reviewed-on: http://review.coreboot.org/4335 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-07elog: handle ROM_SIZE differences from detected flash sizeAaron Durbin
The elog code calculates flash offsets and their equivalent addresses in the memory address space. However, it assumes the detected flash size is entirely mapped into the address space. This can lead to incorrect calculations. Add code to allow ROM_SIZE to be less than detected flash size. The underlying assumption is that the first ROM_SIZE bytes are programmed into the larger device. Change-Id: Id848f136515289b40594b7d3762e26e3e55da62f Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/60501 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4332 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-07Correct file permissions.Idwer Vollering
Some files have incorrect/odd permissions, correct them: remove unnecessary +x flags. Change-Id: I784e6e599dfee88239f85bb58323aae9e40fb21c Signed-off-by: Idwer Vollering <vidwer@gmail.com> Reviewed-on: http://review.coreboot.org/4490 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins) Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
2013-12-07src/vendorcode/amd: remove Visual Studio remnants.Idwer Vollering
Delete files that (were overlooked and) are probably needed to build with Visual Studio. Remove doxygen helper files as well. Change-Id: I6b6cece178917ad9da1081eb6b1bb9be33066a77 Signed-off-by: Idwer Vollering <vidwer@gmail.com> Reviewed-on: http://review.coreboot.org/4489 Tested-by: build bot (Jenkins) Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
2013-12-06arch/x86: Do not run UPDATE-FIT if we don't include microcodeAlexandru Gagniuc
The original intention was to only run UPDATE_FIT when a microcode file was included in CBFS. This happens when either CPU_MICROCODE_CBFS_GENERATE or CPU_MICROCODE_CBFS_EXTERNAL is selected, however, the makefile checked that CPU_MICROCODE_IN_CBFS was selected instead. The end result was that on hasswell, the UPDATE-FIT step was always run, even when no microcode was included, generating a build error. Instead, introduce a new variable which tells if a microcode update is added in CBFS during the build. Change-Id: I28638912ed6f77761ef8a584f7636dc907b7a9b7 Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/4480 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-12-06usbdebug: Hide irrelevent options from menuconfigKyösti Mälkki
No need to show the choice of USB port or controller in case of older hardware where location for usbdebug was hardwired. Change-Id: Ia186bf2c6ed60be2834cf6fd0a1965c8bf81ed4d Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/4290 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-06butterfly: Fix build without ChromeOSKyösti Mälkki
Use a file in CBFS for keyboard layout and ethernet MAC instead of scanning FMAP. Change-Id: I7658c7c4e389deb20d7d8f57cce8b568efdc575d Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/4307 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-06Do not export variables to GRUB buildVladimir Serbinenko
Variables in coreboot and not in line with GRUB ones. E.g. HOSTCC is both HOST_CC and BUILD_CC for GRUB (consult INSTALL for more details) and what coreboot calls CC is TARGET_CC for GRUB. Current code plugs this by defining variables explicitly but it has a nasty effect that make stops caring about flags added in makefile itself. Undef as many variables as possible but still pass them to configure for them to have correct effect and keep CC assignment as my make version doesn't undefine it even when instructed to do so. Tested with qemu. Change-Id: I9d18f557138a20ae3918d698dee8f5b5c5738f75 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/4310 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-12-06qemu: fix GENERATE_ACPI_TABLES=n in fw_cfg.cGerd Hoffmann
Change-Id: Ib8dc069c9e503747c349e96a466feb42279afd08 Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Reviewed-on: http://review.coreboot.org/4305 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-06Add in the Makefile bits for the new intel gma driverRonald G. Minnich
The Intel GMA driver is in, this CL splices in the Makefile bits. Change-Id: Icf42a537575b8cc90a679ec1fc15b09294630611 Signed-off-by: Ronald G. Minnich <rminnich@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/60346 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Commit-Queue: Ronald G. Minnich <rminnich@chromium.org> Tested-by: Ronald G. Minnich <rminnich@chromium.org> Reviewed-on: http://review.coreboot.org/4331 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-05abuild: fix and enable USE_XARGS configurationPatrick Georgi
USE_XARGS mode builds n boards in parallel (with 1 CPU each) instead of building 1 board with n CPUs. This requires the main build system to work under such circumstances. Change-Id: Ib4571a78dfe78fd61ae5b26c18be9745bd8b3d52 Reviewed-on: http://review.coreboot.org/4485 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-12-05sconfig: avoid regenerating the binary all the timePatrick Georgi
This makes USE_XARGS-abuild unhappy due to races Change-Id: I1237468366c7f8af7eacd572c2bd32df9a3d58ca Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/4486 Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: build bot (Jenkins)
2013-12-05FUI: add intel_dp driver derived from kernel functionsRonald G. Minnich
These functions are not all used yet, but do compile and are partially used in the FUI testing. They were extracted from the 3.4 kernel using coccinnelle filters. The .c files are only compiled in if CONFIG_INTEL_DP is set. Change-Id: Id95622a75aa02b496c9ea4717cb143394a8332e3 Signed-off-by: Ronald G. Minnich <rminnich@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/60245 Commit-Queue: Ronald G. Minnich <rminnich@chromium.org> Tested-by: Ronald G. Minnich <rminnich@chromium.org> Reviewed-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/4329 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-05haswell: pull in the init code for FUIRonald G. Minnich
Removed two unnecessary register sets, and did the power well a bit more correctly. Also, added a register definition include file so we can used constants instead of magic numbers. We also set registers to common initialized values that are needed for FUI, VBIOS, and kernel. This set of registers appears to be an absolute bare minimum. Since we're hoping to use FUI for all chipsets from this one forward, we unconditionally do the setting here. Signed-off-by: Ronald G. Minnich <rminnich@google.com> Change-Id: Ife3f661ba010214d92b646b336f2b06645119f17 Reviewed-on: https://gerrit.chromium.org/gerrit/59988 Reviewed-by: Stefan Reinauer <reinauer@google.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Commit-Queue: Ronald G. Minnich <rminnich@chromium.org> Tested-by: Ronald G. Minnich <rminnich@chromium.org> Reviewed-on: http://review.coreboot.org/4328 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-05google/link: use the new edid functions when in FUI modeRonald G. Minnich
The new edid functions support converting the edid to an lb_framebuffer. Use them. Also, since panels seem to set bits per color instead of bits per pixel, just force the right value in the edid struct. Add helpful comment because people don't always believe we need to set the pallette. While we're at it, fix a problem that caused it to not compile. Change-Id: I645edc4e442d9b96303d9e17f175458dc7ef28b6 Signed-off-by: Ronald G. Minnich <rminnich@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/57619 Reviewed-by: Stefan Reinauer <reinauer@google.com> Commit-Queue: Ronald G. Minnich <rminnich@chromium.org> Tested-by: Ronald G. Minnich <rminnich@chromium.org> Reviewed-on: http://review.coreboot.org/4327 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-05lynxpoint: Update LPT-LP PM settingsDuncan Laurie
- updates from 1.6.0 ref code - remove the step comments as they are no longer even close - add constants for LPT revisions build and boot on Falco Check that RCBA+2300[1] is set: > mmio_read32 0xfed1e300 0x00000002 Change-Id: I8b3c5fda3f3170455699a7834239cb991603e7a8 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/59821 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4326 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-05lynxpoint: enable clock gatingAaron Durbin
Implement the LynxPoint BIOS Spec for clock gating. Change-Id: Iaa84cb447bd29b0d13cdda481a1661ea40499de1 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/59590 Reviewed-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/4325 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-05lynxpoint: provide gpio_is_native()Aaron Durbin
There's a need to determine if a specific gpio pin is is set up to be a native function or not. Implement this. Change-Id: I91d57a549e0f4fddc0b1849e5f74320fc839642c Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/59589 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4324 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-05lynxpoint: implement additional programming stepsStefan Reinauer
The BIOS spec for LynxPoint calls out additional programming steps for the PCIe Root Ports. Implement those steps from the BIOS spec. These steps are completed before deeper PCIe probing. The "late" programming was removed as that was applicable to Cougar/Panther point where this code was originally copied, though there was some overlap. Change-Id: I64f25e4451e035d98ca6b66b0335bd280b70b074 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/59558 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4323 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-05lynxpoint: disable pcie devices based on configAaron Durbin
PCIe Root Ports should be disabled based on pin ownership and the strapping configuration. Implement this logic for LynxPoint. The chip_ops->enable_dev() path is no longer used. Instead the PCIe driver handles the enabling and disabling of devices. This allows for having an empty or incomplete device tree since those "allocated" devices do not travel through the chip_ops->enable_dev() path. The coalescing was tested to be working properly, however not all configurations were tested. Change-Id: I1e8bfe5e447b72ff8a4b04b650982d8c1ae0823c Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/59424 Reviewed-by: Stefan Reinauer <reinauer@chromium.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4322 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-05peppy: Disable forced dev mode.Shawn Nematbakhsh
Don't force dev mode. Allow users to enter / exit dev mode as normal. Change-Id: I168eb04a8ac102a8c4a1ca8936f78f62b001e0eb Reviewed-on: https://gerrit.chromium.org/gerrit/59492 Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org> Tested-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-by: Dave Parker <dparker@chromium.org> Reviewed-on: http://review.coreboot.org/4321 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-05libpayload: Have similar cache api on ARM and x86Stefan Reinauer
So far this is used by the USB driver, and instead of having ifdefs all throughout that code, implement the same API on x86 and ARM. Change-Id: I8093ad818ad2e38a0901787aa8674faf591d580c Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/56105 Reviewed-by: David Hendricks <dhendrix@chromium.org> Commit-Queue: Stefan Reinauer <reinauer@chromium.org> Tested-by: Stefan Reinauer <reinauer@chromium.org> Reviewed-on: http://review.coreboot.org/4320 Tested-by: build bot (Jenkins)
2013-12-05Fix Makefile to include all copies of the SPD sourcesDuncan Laurie
On some systems there may be 2GB SKU that is the same as the 4GB SKU but just one channel of memory. In that case we need to ensure that both copies of the same SPD source end up populated by ensuring that repeated entries are included by using $+ instead of $^. Alternatively we could do the check inside romstage, but it is already set to behave this way if the SPD gets populated correctly. I changed spd_index to 3 in falco romstage to force it to pretend it was a 2GB config of the same memory, then booted to ensure it was indeed limited to 2GB. memcfg channel[0] config (00780008): ECC inactive enhanced interleave mode on rank interleave on DIMMA 2048 MB width x16 single rank, selected DIMMB 0 MB width x16 single rank memcfg channel[1] config (00600000): ECC inactive enhanced interleave mode on rank interleave on DIMMA 0 MB width x8 single rank, selected DIMMB 0 MB width x8 single rank Change-Id: Ibfe5051ccda2fe69e8caff3f3c264116e3411c65 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/59483 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: Jay Kim <yongjaek@chromium.org> Reviewed-on: http://review.coreboot.org/4319 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-05cbmem: print timestamp namesStefan Reinauer
The numbers alone are hard to parse, so add some timestamp names to make it easier to read. Change-Id: Ie32d3e7ca759bd15e7c160bdd829dec19943e6cb Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/65333 Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-by: Ronald G. Minnich <rminnich@chromium.org> Reviewed-by: Marc Jones <marc.jones@se-eng.com> Commit-Queue: Stefan Reinauer <reinauer@chromium.org> Reviewed-on: http://review.coreboot.org/4314 Tested-by: build bot (Jenkins)
2013-12-05Fix timestamp output in cbmem utility on ARMStefan Reinauer
On ARM the timestamps are already in micro seconds, so no need to convert them. Signed-off-by: Stefan Reinauer <reinauer@google.com> Change-Id: If7363b0703e144bde62d9dab4ba845e1ace5bd18 Reviewed-on: https://gerrit.chromium.org/gerrit/63991 Reviewed-by: Vadim Bendebury <vbendeb@chromium.org> Commit-Queue: Stefan Reinauer <reinauer@chromium.org> Tested-by: Stefan Reinauer <reinauer@chromium.org> Reviewed-on: http://review.coreboot.org/4313 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-05Add scripts to export board status data to wikiPatrick Georgi
It's a start... Change-Id: Ibdb0b64ab0349df58bcad5ce553bf0dbec636925 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/4483 Tested-by: build bot (Jenkins)
2013-12-05libpayload: Clean up CFLAGSStefan Reinauer
- Add -ffreestanding and -fomit-frame-pointer for all platforms. - Add ARMv7 specific flags to the armv7 Makefile Change-Id: I71ab1b096e505940cc20c266bccd43917bcfad3a Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/56104 Commit-Queue: Stefan Reinauer <reinauer@chromium.org> Reviewed-by: Stefan Reinauer <reinauer@chromium.org> Tested-by: Stefan Reinauer <reinauer@chromium.org> Reviewed-on: http://review.coreboot.org/4317 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-05AMD Kabini: fix issue 'S3 fails to suspend after wake up from USB keyboard'Zheng Bao
Propagated from http://review.coreboot.org/3347 http://review.coreboot.org/3374 The cause of this issue is: USB devices use bit 11(0x0b) of GP0_STS represents S3 wake up event, but this bit is not clear after wake up. So OS thinks there is a wake up signal and wake up immediately. Both amd/olivehill and asrock/imb-a180 have been validated. Change-Id: I7c26cb07bcd2e62bb792809b67314e5155c6adf6 Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/4261 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-05AMD Kabini: Add ACPI sleep/wakeup calls for southbridgeZheng Bao
The AML code of PTS and WAK for southbridge are in UINT8 AlibSsdtKB[], Proc/GNB/Modules/GnbInitKB/AlibSsdtKB.h. It was integrated into SSDT even it was called by nobody. The source ASL was provided by AGESA for reference, but it has been scrubbed when it was ported to Coreboot. Without the calls, Olive Hill can not wake up if it boots Windows. Both amd/olivehill and asrock/imb-a180 have been validated. Change-Id: Ia7bba29904dbd6f33fdb08bf88bb499005ef561b Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/4260 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-12-05AMD IMC AGESA: Access the data in stack by correct lengthZheng Bao
The bug is hard to find. We were adding the feature of fan control. We met some strange things which could not be explained. Like, sometimes adding printk let the error disappear. Then we traced the code by hardware debug tool (HDT). It turned out the data in stack was overwritten. The values of AccessWidthxx are { AccessWidth8 = 1, AccessWidth16, AccessWidth32,} For the case of AccessWidth8, we only need to access the index/data once. But ReadECmsg and WriteECmsg did the loop twice, 1 more time than they are supposed to do. The data in stack next to "Value" would be overwritten. For all the cases, the code should be OpFlag = OpFlag & 0x7f; switch (OpFlag) { case 1: /* AccessWidth8 */ OpFlag = 0;break; case 2: /* AccessWidth16 */ OpFlag = 1;break; case 3: /* AccessWidth32 */ OpFlag = 3;break; case 4: /* AccessWidth64 */ OpFlag = 7;break; default: error; } Actually, the caller only takes AccessWidth8 as the parameter. We can ignore other cases for now. That is an AGESA bug. AMD's AGESA team own this code. They have given the response that they are going to update this in next release. I presume let them decide the proper way to fix that. Before that, I change the code as little as possible to make it run without crash. Change-Id: I566f74c242ce93f4569eedf69ca07d2fb7fb368d Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/4297 Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins)
2013-12-05cpu: Remove BOARD_MICROCODE_CBFS_GENERATE Kconfig optionAlexandru Gagniuc
Commit * bdafcfa Add the Intel FSP 206ax CPU core support Introduced this option. This option was meant to have a board generate a CBFS file containing microcode. However, microcode generation used to be enabled by default when CPU_MICROCODE_IN_CBFS was selected. The introduction of BOARD_MICROCODE_CBFS_GENERATE killed that automatic default, which is not what we want. This option is misguided in the sense that it tends to introduce a non-default which had been intentionally a default. We now have to select two Kconfig options in order to generate microcode in CBFS, meaning one option is redundant. Change-Id: I3034833df1a9afa7d6d9d537484cb4ac89d30183 Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/4478 Tested-by: build bot (Jenkins)
2013-12-05intel/fsp_bd82x6x: Use correct type pointer for mainboard_smi_gpiAlexandru Gagniuc
mainboard_smi_gpi has recently been updated to take a u32 argument from a u16, but the patch introducing the fsp_bd82x6x support has been verified on a master before this change, thus resulting in a 'cast from incompatible type' error. Update the pointer to the correct size argument. Change-Id: I9d62ee43f7c8ed774898f54d29a87cf463b76e91 Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/4479 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-12-05libpayload: sync ARMv7 arch/io.h with corebootStefan Reinauer
On ARMv7 we need to carefully add memory barriers to all memory read and write operations. This change brings libpayload in sync with what coreboot is doing. Signed-off-by: Stefan Reinauer <reinauer@google.com> Change-Id: Ie9c30b0f0d30531c5f9d99c2729246a86b8cec26 Reviewed-on: https://gerrit.chromium.org/gerrit/59294 Reviewed-by: Gabe Black <gabeblack@chromium.org> Tested-by: Stefan Reinauer <reinauer@chromium.org> Commit-Queue: Stefan Reinauer <reinauer@chromium.org> Reviewed-on: http://review.coreboot.org/4316 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-12-05qemu-armv7 CPU: Move Kconfig code into CPU directoryStefan Reinauer
Signed-off-by: Stefan Reinauer <reinauer@google.com> Change-Id: Icae8042add5f4dd5c707369ffc4587c613d69d29 Reviewed-on: https://gerrit.chromium.org/gerrit/59324 Reviewed-by: Stefan Reinauer <reinauer@chromium.org> Tested-by: Stefan Reinauer <reinauer@chromium.org> Commit-Queue: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/4315 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-12-04cbmem: fix userspace utility to work with dynamic CBMEMStefan Reinauer
This also adds an option -x/--hexdump to dump the whole CBMEM area for debugging. Change-Id: I244955394c6a2199acf7af78ae4b8b0a6f3bfe33 Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: https://gerrit.chromium.org/gerrit/62287 Reviewed-by: David Hendricks <dhendrix@chromium.org> Commit-Queue: Stefan Reinauer <reinauer@chromium.org> Tested-by: Stefan Reinauer <reinauer@chromium.org> Reviewed-on: http://review.coreboot.org/4312 Tested-by: build bot (Jenkins)
2013-12-04cbmem: Implement ARM supportStefan Reinauer
on ARM the CBMEM utility requires the procfs entry /proc/device-tree/firmware/coreboot/coreboot-table provided by the FDT (dynamically created by depthcharge at the moment) Signed-off-by: Stefan Reinauer <reinauer@google.com> Change-Id: If5f961afb23791af6f32dd4fc9a837a1aa41b70e Reviewed-on: https://gerrit.chromium.org/gerrit/59322 Reviewed-by: Stefan Reinauer <reinauer@chromium.org> Tested-by: Stefan Reinauer <reinauer@chromium.org> Commit-Queue: Stefan Reinauer <reinauer@chromium.org> Reviewed-on: http://review.coreboot.org/4311 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-12-04lenovo/x60: Drop global oprom_is_loadedKyösti Mälkki
Variable use is specific to ChromeOS. Change-Id: I5b61a038e6b08e3b2408c4d990749d45fdf2148d Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/4306 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-12-04lumpy: Fix build without ChromeOSKyösti Mälkki
Change-Id: I1a59405499deceed7df01a03834be72830e6578f Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/4291 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-12-04intel/cougar_canyon2: Intel CRB FSP based mainboardMarc Jones
Cougar Canyon 2 is a Ivybridge/PantherPoint reference board. This implementation uses the Intel FSP (Vist the Intel FSP website for details on FSP architecture and support). The FSP does not support s3 at this time. S3 may be added when it is available in the FSP. All other features and IO ports are functional. Booted on Ubuntu 12.04 and 13.04, Fedora 18 with SeaBIOS payload. Memtest86, FWTS, and other tests pass. Board support page will be updated on acceptance. Change-Id: I26c0b82d7ac295498376ad4c3517a9d6660d1c01 Signed-off-by: Marc Jones <marc.jones@se-eng.com> Reviewed-on: http://review.coreboot.org/4018 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-12-04Update SMM for FSP systemsMarc Jones
Add the FSP northbridge and southbridge includes. Change-Id: I5c7f395dc033caa8d0bf0313382769595d77f2a5 Signed-off-by: Marc Jones <marc.jones@se-eng.com> Reviewed-on: http://review.coreboot.org/4019 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-12-04Add Intel FSP bd82x6x southbridge supportMarc Jones
Add support for the bd82x6x using the Intel FSP. The FSP is different enough to warrant its own source files for now. The mrc/system agent chromebook solution does much more southbridge initialization and configuration than the FSP version. It may be combined in the future. Change-Id: Ie493945f3d321d854728d231979a0c172d2b36de Signed-off-by: Marc Jones <marc.jones@se-eng.com> Reviewed-on: http://review.coreboot.org/4017 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-26 13:40:35 +0000