| Age | Commit message (Collapse) | Author |
|---|
|
This renames bus to upstream and link_list to downstream.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I80a81b6b8606e450ff180add9439481ec28c2420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
GPP_E08 and GPP_E22 were set incorrectly previously.
This CL corrects these settings according to schematics.
BUG=b:305793886
TEST=Built FW image correctly.
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I8e427350e1ee564f9d6566bdfe1f42c92c87a711
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Macros can be confusing on their own; hiding commas make things worse.
This can sometimes be downright misleading. A "good" example would be
the code in soc/intel/xeon_sp/spr/chip.c:
CHIP_NAME("Intel SapphireRapids-SP").enable_dev = chip_enable_dev,
This appears as CHIP_NAME() being some struct when in fact these are
defining 2 separate members of the same struct.
It was decided to remove this macro altogether, as it does not do
anything special and incurs a maintenance burden.
Change-Id: Iaed6dfb144bddcf5c43634b0c955c19afce388f0
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80239
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
With Cr50, the GPIO EC_IN_RW is used to determine whether EC is trusted. However, With the switch to Ti50, it is determined by Ti50's boot mode. If the boot mode is TRUSTED_RO, the VB2_CONTEXT_EC_TRUSTED flag will be set in check_boot_mode(). Therefore in the Ti50 case get_ec_is_trusted() can just return 0.
The current code of get_ec_is_trusted() only checks the GPIO, which
causes the EC to be always considered "trusted". Therefore, correct the return value to 0 for TPM_GOOGLE_TI50.
BUG=b:321172119
TEST=emerge-nissa coreboot chromeos-bootimage
TEST=firmware_DevMode passed in FAFT test
Change-Id: I308f8b36411030911c4421d80827fc49ff325a1b
Signed-off-by: Qinghong Zeng <zengqinghong@huaqin.corp- partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add RAM ID for
H58G66BK7BX067 0 (0000)
BUG=b:322528721
BRANCH=firmware-rex-15709.B
TEST=Run part_id_gen tool without any errors
Change-Id: I31538988d1329d9e2f45d862eb0ae05c0d6a179e
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Check MTL EDS2, SOC_TCHSCR_RST(GPP_C01) default setting is NF1.
Set SOC_TCHSCR_RST to output low in early_gpio_table.
BUG=none
TEST=Build and test on karis, touchscreen function works
Change-Id: Ieebd3cf3c320bc895d036c372f792ec7b5d7ebf9
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Move the definition of the TCO registers used in most boards to a
separate file and use it consistently. Do not unify TCO for older
incompatible platforms.
BUG=b:314260167
TEST=none
Change-Id: Id64a635d106cea879ab08aa7beca101de14b1ee6
Signed-off-by: Marek Maslanka <mmaslanka@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80005
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
|
|
Follow reference design rex0, toggles NVMe PWR pin as soon as
in early stage to make NVMe ready sooner.
BUG=none
TEST=Build karis and try warm reboot from OS console. Check the DUT
with WD SSD boots to OS again.
Change-Id: I24a702f02278355c4f2137f0d05c8a9da7cb3c1c
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80213
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current panel voltage measured at mainboard side is 1.79V and the
voltage at panel side is 1.74V. Since the panel requires 1.8V or more,
increase the circuit voltage to 1.9V to meet the panel requirement.
After adjustment mainboard side voltage is 1.89V and panel side is
1.84V.
BUG=b:322080023
TEST=Check ciri vm18 ldo voltage
BRANCH=None
Change-Id: I6d6193d45409f53c0b656890c44ddaef253c5e01
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80198
Reviewed-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4bdfcd0cc0e2d9b5f884ea7275659c12488715e0
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80194
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
GCC_OPTIONS is only used for target specific options right now,
so rename to TARGET_GCC_OPTIONS and only use them in the
non-bootstrap build.
Adapt BINUTILS_OPTIONS for consistency, even though it doesn't
have the same problem.
Change-Id: I5e4f54b758dd7daf4e69101c19dfa1212fa64cf6
Signed-off-by: Patrick Georgi <patrick@georgi.software>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80229
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Id86ebc20cf5af5b65812c3f09235d0cba86d13f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80126
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
It's what this function family is defined to do, we currently don't
usually run into the case (see: not too many die() instances going
around), it's more useful to try to recover, and the JPEG parser can run
into it if the work buffer size exceeds the remaining heap, whereas its
sole user (the bootsplash code) knows what to do when seeing a NULL.
Use xmalloc() if you want an allocation that either works or dies.
tl;dr: That code path isn't usually taken. Right now it crashes. With
this patch it _might_ survive. There is a use-case for doing it like
that now.
Change-Id: I262fbad7daae0ca3aab583fda00665a2592deaa8
Signed-off-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Multiple links are unused throughout the tree and make the code more
confusing as an iteration over all busses is needed to get downstream
devices. This also not done consistently e.g. the allocator does not
care about multiple links on busses. A better way of dealing multiple
links below a device is to feature dummy devices with each their
respective bus.
This drops the sconfig capability to declare the same device multiple
times which was previously used to declare multiple links.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Iab6fe269faef46ae77ed1ea425440cf5c7dbd49b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78328
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jincheng Li <jincheng.li@intel.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
CXL IIO stacks
When an IIO stack is connected with CXL cards, its bus range
will be divided by a PCI host bridge object and a CXL host
bridge object, otherwise, all its range will be owned by the
PCI host bridge object. Accordingly, CXL ACPI resources should
be only created when the IIO stack is connected with a CXL
card.
TEST=intel/archercity CRB
Change-Id: I6c1b1343991bc73d90a433d959f6618bbf59532f
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80087
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently resource allocation starts top down from the default value
0xfe000000. This does not match what ACPI reports, so adapt
CONFIG_DOMAIN_RESOURCE_32BIT_LIMIT to reflect that.
Change-Id: I32d08ffd5bbd856b17f7ca2775c5923957d92c85
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Adding downstream busses at runtime is a common pattern so add a helper
function.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ic898189b92997b93304fcbf47c73e2bb5ec09023
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The CRAT (Component Resource Attribute Table) isn't used on the APUs
from Renoir on and has also been marked as deprecated in version 6.5 of
the ACPI specification. So remove the 'TODO: look into adding CRAT'
comment from all SoCs from Renoir/Cezanne on.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3ea1e3678608b0ace2a1ff7fc104594e90c91476
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80227
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the acpi_add_fsp_tables implementation is identical for all SoCs,
factor it out and move it to the common AMD FSP code. Also guard the
acpi_add_fsp_tables call in soc_acpi_write_tables with
if (CONFIG(PLATFORM_USES_FSP2_0)) to properly handle the FSP dependency.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8917a346f586e77b3b3278c73aed8cf61f3c9e6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80225
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Factor out acpi_add_fsp_tables from the soc_acpi_write_tables function
and move the remaining parts of the soc_acpi_write_tables function to
the SoC's acpi.c. This aligns the other family 17h/19h SoCs more with
Genoa and only leaves the FSP-specific code in agesa_acpi.c which will
be made common in a following patch. I decided against also renaming
agesa_acpi.c to acpi_fsp.c, since that would have made the diff less
readable and the files get deleted in a following patch anyway.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia87ac0e77c5e673e694703b85a4bab85a34b980e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Factor out the code to add the CRAT ACPI table into a separate file and
add the acpi_add_crat_table function that can then be called from
soc_acpi_write_tables to better isolate all code specific to the CRAT
table.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4a7853748512811d3d4e124224fcd459e527522c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80223
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ACPI_SCI_IRQ is defined as 9 for all AMD SoCs, so move the definition to
the common amdblocks/acpi.h. Since all but Stoneyridge's soc/acpi.h are
now empty, delete those files too.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8210c98dc4cf2c6001d5273d132053278ff7fea5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80222
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the definition is the same for all SoCs, move it to the common
amdblock/acpi.h header. Since the Stoneyridge northbridge.c file also
includes this prototype, remove the static attribute of the function
there.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib9aa215f2b4ba58f43fed2c751d989f1719e0a17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80221
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The southbridge_write_acpi_tables function uses a struct device type
parameter, but device/device.h that provides the definition wasn't
included.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5245fa132ec9b84bbc483a31788bcd6fac0736e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
add_agesa_fsp_acpi_table should use the same type for the 'current'
parameter and return value as the calling soc_acpi_write_tables does.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie9f770b1d847ea28e4dbd96298a723d794b91a02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
A pointer to soc_acpi_write_tables gets assigned to the
write_acpi_tables element of the device_operations struct, so make sure
that the function has the expected function signature which in this case
means using unsigned long as type for both the 'current' parameter and
the return value.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iee45badb904fa20c6db146edbc00c40ca09361d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80218
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It's not the AGESA code that generates most of the ACPI tables, so
rename the function. This also aligns the other SoCs more with Genoa.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6b2e6c4cb7139c8bde01b4440ab2e923a1086827
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80217
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As a result of hardware changes on this board, the PHY previously
routed to the PSE GbE 1 is now routed to PSE GbE 0 on the Elkhart Lake
SoC.
This patch changes the device PCI ID in the board's devicetree and
accordingly, the GPIO configuration.
BUG=none
TEST=Boot into Linux and observe whether both PSE GbE 0 and PCH GbE
are working, while PSE GbE 1 remains inactive (not listed by 'ip link')
.
Change-Id: I322371f944d15134e6f48ecd84a4026c2fced27b
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The currently used panel type could work with 500 ms but increasing
the value to 1 second allows to use a wider range of LVDS LCD panels,
as many of them specify the delay of 1 s as minimum.
The patch has already been made for mc_ehl3 and serves the purpose of
standardization.
commit c0221aa980d3 ("mb/siemens/mc_ehl3/lcd_panel.c: Set LVDS re-power
delay to 1 s")
Change-Id: Ife26ff27b41298ceeed7d9aed0c1ae5553ab5ff8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
This patch enables Cnvi BT Audio Offload feature and also
configures the virtual GPIO for CNVi Bluetooth I2S pads.
BUG=b:303157827
TEST=Build and boot to anraggar. Verify the config from serial logs.
w/o this CL -
```
[SPEW ] -- CNVi Config --
[SPEW ] CNVi Mode= 1
[SPEW ] Wi-Fi Core= 1
[SPEW ] BT Core= 1
[SPEW ] BT Audio Offload= 0
[SPEW ] Pin Muxing
```
w/ this CL -
```
[SPEW ] -- CNVi Config --
[SPEW ] CNVi Mode= 1
[SPEW ] Wi-Fi Core= 1
[SPEW ] BT Core= 1
[SPEW ] BT Audio Offload= 1
[SPEW ] Pin Muxing
```
Change-Id: I9e6731c8ceaad6ee58b525d4246fa769bfe1b0c7
Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80001
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add WIFI SAR table for omniknight.
BUG=b:320172979
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I70e79577612b3d5c4dc0f92211f87cbea0532d5d
Signed-off-by: jamie_chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80152
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This patch refactors GPR0 unlock function to add few important
logic as below
1. Perform GPR0 unlock if GPR0 is locked.
2. While unlocking dump the GPRD PCH strap details
3. Additionally, print the GPR start and end range if GPR0
protection is enabled.
TEST=Able to test GPR0 protection on google/rex and google/yahiko.
Exp 1: Trying to unlock GPR0 protection for a locked image
> ifdtool -p mtl -g image.bin -O image.bin_unlock
File image.bin is 33554432 bytes
Value at GPRD offset (64) is 0x83220004
--------- GPR0 Protected Range --------------
Start address = 0x00004000
End address = 0x00322fff
Writing new image to image.bin_unlock
Exp 2: Trying to unlock GPR0 protection for a unlocked image
> ifdtool -p mtl -g image.bin_unlock -O image.bin_unlock
File image.bin_unlock is 33554432 bytes
GPR0 protection is already disabled
Change-Id: Id35ebdefe83182ad7a3e735bdd2998baa0ec3ed7
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80216
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This patch ensures the baseboard and variant configs (inside Kconfig
and Kconfig.name) are organized in alphabetic order.
TEST=execute make menuconfig and verify the google/rex variants
order are alphabetically correct.
Change-Id: I0acc2cec21b4607856127b04c400ec416f0c0dd2
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80206
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the new memory support:
Samsung K4U6E3S4AB-MGCL
BUG=b:320137193
BRANCH=firmware-dedede-13606.B
TEST=Run command "go run ./util/spd_tools/src/part_id_gen/\
part_id_gen.go JSL lp4x \
src/mainboard/google/dedede/variants/galtic/memory/ \
src/mainboard/google/dedede/variants/galtic/memory/\
mem_parts_used.txt"
Change-Id: I3f6c784a194e141a3dd1e5a37b3cf12106e692d6
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80150
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:300690448,b:319393777
BRANCH=None
TEST=tested on a device with i2cdetect
Also tested with evtest and make sure Wacom is listed
Change-Id: I4f528b0d778c8c4a4e83774d5c167ccb2d6afd9a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79895
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is causing an assertion error on the devices that don't have CNVi
enabled because CNVi is hidden behind a FW_CONFIG flag in the
overridetree now.
BUG=b:319188820
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
make sure we can boot to kernel on device.
Change-Id: Ifcfbc04825d4d4e7f2874a4c52f9c5cf3e657856
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80211
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Added Lunar Lake device IDs the device specific functions
Reference:
Lunar Lake External Design Specification Volume 1 (734362)
Change-Id: Id31d567287b9921d60909b1eb617c7cfaf6672c9
Signed-off-by: Appukuttan V K <appukuttan.vk@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Saurabh Mishra <mishra.saurabh@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib69236fb5d68272f92405512dc231fa75ecccaa6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This adds the ability to add a flat-binary using menuconfig.
Test: boot hifive-unmatched mainboard with the following config:
CONFIG_PAYLOAD_NONE=n
CONFIG_PAYLOAD_ELF=y
CONFIG_PAYLOAD_FILE="~/repos/linux-riscv/arch/riscv/boot/Image"
CONFIG_PAYLOAD_IS_FLAT_BINARY=y
CONFIG_PAYLOAD_OPTIONS="-l 0x82000000 -e 0x82000000"
CONFIG_COMPRESSED_PAYLOAD_LZMA=y
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I48c6b53a0c9f5b173c89f1a294a0c37fa1a58f31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79950
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the verstage on PSP files in vendorcode from the fsp subdirectory
to a new psp_verstage subdirectory, since those files aren't specific to
the case of the FSP being used for the silicon initialization.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic47f8b18bc515600add7838f4c7afcb4fff7c004
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80209
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This patch adds APCB blobs to the mainboard directory and it replaces
CB:76445 Also this brings onyx_poc mainboard inline with how APCB are
included in other AMD mainboard: commit 95d05d830162 ("mb/google/zork:
Add and use APCB configuration data"), commit I352f58e0d39 ("mb/google/
skyrim: Add and use APCB configuration data") and commit I1c34528fa0f
("mb/amd/onyx_poc: Add and use APCB configuration data").
BUG=none
TEST=build/boot onyx_poc
Change-Id: I1c34528fa0fd15b847c22c995713078c60ac3873
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80204
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of open-coding this functionality in all AMD SoCs, factor it out
into a common implementation.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Idb65c398b747e70ec67107e0a1d4bd6551501347
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80208
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
As with other devices with only an external display, the Librem mini/
mini-v2 need a few extra seconds (vs an internal panel) for display init in order for the edk2 boot splash to be visible before the
default boot target is booted.
TEST=build/boot Librem Mini v2 w/edk2 payload, verify splash screen
shown / user has time to enter setup menu.
Change-Id: I9d2d514719a9918ee58cc63969b3adae44ac1632
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ieaf7894f49a90f562b164924cc025e3eab5a3f7f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I464170e60a22f39225044c6794d091455d931e9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80128
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib77cb3a0852092ac414fe0160fe10d6e58fcf660
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80127
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I2a6a4d1eb7e0d0cd32c8690caf3eff340cdb0d8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80124
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I434940ebb46853980596f7ad55d27a62c90280fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Id09eafd293a54198aab87281f529749325df8b07
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
If the smbios table is not below 4G there is no need to have a 32 bit
entry point. Even worse it could cause the payload to try to use the
entry point.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I4cb426bb0c45282ed03ff4c65d15004b7f985dab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Alphabetize the ordering of model configs and selects in Kconfig and
Kconfig.name
BUG=None
BRANCH=None
TEST='emerge-brya coreboot' and verify it builds.
Change-Id: Id9347421337d451ce72fcf3984489b06f372f70c
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This change eliminates the unnecessary override of the tcc_offset
chip configuration to 10, as the default rex baseboard now handles
this setting correctly.
TEST=Successfully built and booted google/karis, confirming tcc_offset
remains at 10.
Change-Id: Ie40db1431fb0197ee360ad5656878e57f51c855b
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Follow thermal team request, override tcc_offset to 20.
TEST=Build and verified by thermal team using google/screebo.
Change-Id: Idc76f9c0054f21f066b779e6404a1c175eb396a0
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Now that we've added an ACPI device for SATA, add the name back
to the soc_acpi_name() list so the PEPD LPI constraint list
generates a valid reference to the SATA device.
TEST=build/boot Win11 on google/puff (kaisa).
Change-Id: I134058f5ef78f419dc5538452614125ad44bf29d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80059
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add an ACPI stub containing the SATA device in proper scope, along with
the device status, so that there exists a device to be referenced from
the PEPD LPI constraint list. Fixes a Windows BSOD INTERNAL_POWER_ERROR
on devices with enabled SATA ports.
TEST=build/boot Win11 on google/puff (kaisa).
Change-Id: I951c62d09609ed73079fe97ea9ce49fdee333272
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This reverts commit d64b66ba267a217d0b6716309019c36c8cfdf8c2:
"soc/intel/cannonlake: Add missing min sleep state for thermal device."
Reverting because commit e00523aae2ea ("soc/intel/cannonlake: Drop
entries from soc_acpi_name()") removed the ACPI device name for the PCH
thermal device, since there is no ACPI device defined for it. Removing
the name without removing the minimum sleep state caused an invalid LPI
entry to be created, which caused a Windows BSOD: INTERNAL_POWER_ERROR.
TEST=build/boot Win11 on google/puff (wyvern).
Change-Id: I2dfe76d5f72cde7742cee338fa24eaafb84c4604
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80057
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
When the device right below the MPIO chip driver has downstream devices
without another chip in between, those downstream devices will also have
their chip_ops entry set to vendorcode_amd_opensil_genoa_poc_mpio_ops.
To avoid adding the same MPIO descriptor again for those additional
downstream devices, make sure that the chip_info pointer of the device
isn't the same as the one of the parent device, since that's only the
case for those additional downstream devices.
TEST=Onyx still boots to the payload and the MPIO configuration reported
from the openSIL code is still the same
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Nico Huber <nico.h@gmx.de>
Change-Id: I6ba90fdc83ba089127e6722778bfef29dd480bb4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80149
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Call setup_opensil, opensil_entry, and fch_init in the right order from
the init method of the SoC's chip operations. This brings this SoC both
more in line with the other SoCs and avoids using boot state hooks for
this which also makes the sequence in which those functions are called
easier to understand. Previously the boot states were used so that
setup_opensil was run before configure_mpio which was run before
opensil_entry(SIL_TP1), but since configure_mpio is called from
setup_opensil, this is no longer necessary.
TEST=Onyx still boots to the payload and the MPIO configuration reported
from the openSIL code is still the same. The FCH init code now runs
before the resource allocation like on the AMD SoCs that rely on FSP.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic752635da5eaa9e333cfb927836f0d260d2ac049
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79985
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Instead of calling configure_mpio from the init function of the MPIO
chip struct for the first device that has this struct as chip_ops, call
if from setup_opensil. This will allow to do the calls into openSIL from
the SoC's chip_ops init function instead of having to rely on boot state
hooks. configure_mpio needs to be called after the xSimAssignMemoryTp1
call which sets up the openSIL data structures, but before the
opensil_entry(SIL_TP1) call for which the MPIO data structures need to
be filled for it to be able to initialize the hardware accordingly.
Since the vendorcode_amd_opensil_genoa_poc_mpio_ops struct now no longer
assigns configure_mpio to the init function pointer, we have to check
if the device's chip_ops pointer points to
vendorcode_amd_opensil_genoa_poc_mpio_ops instead of checking if the
chip_ops' init function is configure_mpio to match for the devices below
the MPIO chips in the devicetree.
TEST=Onyx still boots to the payload and the MPIO configuration reported
from the openSIL code is still the same
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If37077c879e266763fd2748a1a8d71c63c94729b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Since we pass va_list list to the print function, we need to use vprintk
instead of printk. Earlier versions of this code used vsnprintf and a
local buffer, but when that code was reworked to not need the temporary
buffer, it was replaced by printk instead of the correct vprintk.
TEST=Now the console output from openSIL looks as expected:
Example line from openSIL's console output when it prints the MPIO
configuration from a log some commits before this patch:
Host PCI Address - -1352681400:-1353251983:7
Same line with this patch applied looks how it's supposed to:
Host PCI Address - 0:0:0
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: Varshit Pandya <pandyavarshit@gmail.com>
Change-Id: Ia931cc80dea5b7eabb75cfb19f8baa9a09cd2dbf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80203
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This CL update setting according to schematic v0.4.
BUG=b:320201111
BRANCH=firmware-rex-15709.B
TEST=Built FW image correctly.
Change-Id: Ia4570d26ee9fd175ed9099bd057cee3c30c95704
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80156
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Change-Id: Ida6e87908ae6996529057c8df12dbe046ee54b98
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Looking at photos and service manuals, all the WLAN slots are short
(half-height) and WWAN slots long (full-height).
Change-Id: I894f8216d1b836fbc41423180177bb8651040fbb
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Some variants added the generic gfx driver with an LCD device without
specifying the address, which is required for the backlight controls
to be functional under Windows. Add the address value where missing.
Address value used (0x80010400) is same as on other Brya variants which
did properly set it, and is taken from the ACPI 6.5 spec section B.4.2,
_DOD (display output device enumeration), table B-2:
- bit 31 = use the ACPI-defined (vs vendor-defined) bit scheme for bits
15-0
- bit 16 = platform firmware can detect the device
- bit 10 = display type is internal/integrated flat panel (aka LCD)
TEST=build/boot Win11 on google/brya (osiris), verify ACPI backlight
controls functional.
Change-Id: Id24e330cfb7c993d12665a704e1ca78e2e38874f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
and amplifier
Compatible headphone codec "ALC5682I-VS" and speaker amplifier "ALC1015Q-VB"
BUG=b:183305590
TEST=ALC5682I-VD and ALC1015Q-VB can work normally
Change-Id: I4f212f063a1180d7a1c14769f61b0afef7565cad
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79831
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Endeavour and Karma were missing, leading those devices to have empty
SMBIOS mainboard names. Fix by adding the missing entries.
TEST=build/boot google/fizz (endeavour), verify SMBIOS name correctly
shown via dmidecode.
Change-Id: I1d4fb2473d27ff5611f9d2b962aae2d6bf6d1da0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80181
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There was a mistake in the gpio spreadsheet provided by the HW team
and the GPIO assignments for the EC INT and WAKE signals got switched
from what it was in the schematics. The correct assignments are:
GPP_D0 = EC_PCH_INT_ODL
GPP_D1 = EC_PCH_WAKE_ODL
BUG=b:311450057,b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Will try to boot OS image on device and see if there are any
ec errors.
Change-Id: I02057aeb5d82218dbbe4c939d4feb87a4d3da678
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79886
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new i2c address 0x24 of touch IC for Parade touch panel.
BUG=b:320731709
Test=emerge-nissa coreboot
Change-Id: I51bd89beffd912fc147da11d19f38cb44cbe570a
Signed-off-by: leo.chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
As a preparation for the following patch, rename mpio_config to
configure_mpio to make it both a bit more descriptive and to match the
naming scheme used for the functions that get called by setup_opensil.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic4b1aa6e964cbbb4affb89cacd33af8b24871bb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
Make sure that any new files generated get the Makefile.mk name.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I3880d5911ff8de01751befdffc99ba5a961416f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80113
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Now that the files are renamed, make sure all references to Makefile.inc
are updated as well.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I09e235eecf0c32c80a41bfcbbd3580cce6555e10
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I4790adb41cb62c8c8dd44261a2926dfb6350955a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80111
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Icfdadfa6705a64655b38aca25be0818ec26429f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80110
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib8a2ae26ed4380592d15e1a7b2d682639413af01
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I85cda24aa7dec82d23e8a321dac03ec737f4c503
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80108
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I92f8bd7e1c9fc6e4120fb94c2299a266304e19de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80107
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I134acc26c0a79d974a6dd0a3b257f961db7e2d86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80106
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
1. Adjust VFP and CLK to meet 60 +- 0.01 Hz
2. Fine tune init code for panel internal circuit
Fixes: 520137f("drivers/mipi: Add support for IVO_T109NW41 panel")
BUG=b:320892589
TEST=boot ciri with IVO_T109NW41 panel and see firmware screen
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I4d7c7bd4d79301fbb6d555117d190c358bceafcc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80086
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Added Lunar Lake specific CPU and PCIE device IDs
Reference:
Lunar Lake External Design Specification Volume 1 (734362)
Change-Id: Ic0aae6fd7aa8ba3a6a794f8af5ecf3967509b704
Signed-off-by: Appukuttan V K <appukuttan.vk@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79899
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Saurabh Mishra <mishra.saurabh@intel.com>
Reviewed-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
|
|
Set tcc_offset value to 10 in devicetree for Thermal Control
Circuit (TCC) activation feature for rex.
BUG=b:270664854
TEST=Build, boot and test on rex with value under sysfs
/sys/bus/pci/devices/0000:00:04.0/tcc_offset_degree_celsius
Change-Id: I9012984016ab3213102214025d6d8dc07c5d8974
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79992
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Peter Ou <peter.ou@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I5855f49984db59d786decad6142e3525b146a573
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80105
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I422cb475723006ca42be93508fb0bf4b1e4e84d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80104
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ie7038712de8cc646632d5e7d29550e3260bf2c62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80103
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I41f8a9b5d1bdb647a915da1a5e95161b2e34df28
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80082
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I9eabe84d55fd9f434e4128866810c0e4970f2ae7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80081
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I8cf3d2e2cd1b6ebe4e941ad64f27698379fef696
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80080
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Id47a5ef3c53f767d1e03c788e0022d05b21f5c28
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80079
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I358b878b97adfd9be156a5dd4a9cbaf9e81bca1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I2f299920eb7c6d6f8888cfe5e223ae03093a1d88
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80077
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I41191f6971bdd8ecff2c56f4bfa2b57c87530b83
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80076
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ic80d27a963da8eddc3d1f0d9a3d59763028d4ed0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80075
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I6f502b97864fd7782e514ee2daa902d2081633a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80074
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib479b93b7d0b2e790d0495b6a6b4b4298a515d9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80073
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ie449267fe4fdd75110f577e1b9f748cd06140950
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Iddac15cc42532f44dda44032be0f8525f6347abd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80070
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
Use a union to access the PCI domain ID.
This will become handy in the following commits to gather meta-data
from the domain ID.
Change-Id: I5c371961768410167a571358f6f366847a259eb6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80099
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a function to return the PCI domain device for the specified
device. On multi PCI domain platforms this function allows to
determine which domain and thus which socket the PCI device
belongs to.
Change-Id: I0068b82e139fe7a35e6b1b91b7d386b750c80748
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80090
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add and use inline method to identify the root device.
Change-Id: I394c8668245bcfea6414b8ca5f14ef8135897e59
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80169
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ic060f3605cd18d4bf774573c21957f626f984e2c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80069
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I552d487978906f5ea74c3d0d85373fe5b2de3f38
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80068
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
