| Age | Commit message (Collapse) | Author |
|---|
|
The UART support is needed in SMM in order for DEBUG_SMI to
function.
BUG=chrome-os-partner:54262
TEST=Ran on reef with DEBUG_SMI enabled. Can observed SMI messages.
Change-Id: Ibd6b12e27d5776046b400adf72f24133b9e54af8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15151
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
It appears that PM1 is not wired up to the SMI status register, but
it does definitely cause SMIs to trigger. Therefore, provide a fake
PM1 status bit by checking the power button status when SMI status
is indicating no status as well as the PM1 control indicating that
SCI mode is not enabled.
BUG=chrome-os-partner:54262
TEST=Smashed power button on reef to cause SMI in firmware. No longer
loops infinitely with constant SMIs firing.
Change-Id: I9aa1b5f79b651cbc19a2d3353d9ef65429386889
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15155
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Provide the bit definitions for the SMI status register. Also,
utilize them which means deleting some of the handlers that can't
exist because there are no status bits.
BUG=chrome-os-partner:54262
Change-Id: I389c7cb3cad01ba0eca52a337ffee352a2010bfa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15154
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
Instead of hardcoding the PCI mmio size read it from devicetree.
Set a default value of 2048 MiB and 1024MiB for laptops without
discrete graphics.
Tested on Sandybridge Lenovo T520.
Change-Id: I791ebd6897c5ba4e2e18bd307d320568b1378a13
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15140
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1. The checksum method that was documented is not correct. So, no use
filling in a value based on wrong calculations. This can be added back
once updated information is available.
2. Checksum does not seem to affect the booting up of SoC. So, fill in 0
for now.
Change-Id: I0e49ac8e0e04abb6d7c9be70323612bdef309975
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15145
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Update pack and header order and mark the entries as mandatory and
recommended w.r.t. ordering (mandatory = essential for booting,
recommended = okay to change, but this config is tested and known to work).
Change-Id: Ia089bdaa0703de830bb9553130caf91a3665d2c4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15144
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Since the HTIF is a non-standard interface, and coreboot already has a
8250 driver, I started implementing an 8250 core for spike[1].
[1]: https://github.com/riscv/riscv-isa-sim/pull/53
Change-Id: I84adc1169474baa8cc5837358a8ad3d184cfa51b
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/15150
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In the default (medlow) code model, pointers are loaded with a lui, addi
instruction sequence:
lui a0, 0xNNNNN
addi a0, a0, 0xNNN
Since lui sign-extends bits 32-63 from bit 31 on RV64, lui/addi can't
load pointers just above 0x80000000, where RISC-V's RAM now lives.
The medany code model gets around this restriction by loading pointers
trough auipc and addi:
auipc a0, 0xNNNNN
addi a0, a0, 0xNNN
This way, any pointer within the current pc ±2G can be loaded, which is
by far sufficient for coreboot.
Change-Id: I77350d9218a687284c1337d987765553cf915a22
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/15148
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The uart8250mem driver needs it.
Change-Id: I09e6a17cedf8a4045f008f5a0d225055d745e8db
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/15147
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I12de8f82499074f0fbbc1c09210b00c6a9614c1b
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/15146
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I9759771fa6fc708d7d97509c5f5e0cefb8ab4c96
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/14962
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Due to USB LDO issue in current steppings, cold reboot needs to be
temporarily disabled. Thus, hard_reset call should be the same as
soft_reset.
Once future steppings are available INTEL_COMMON_RESET can be enabled again.
Change-Id: If0ec56db3864d500acc93d2b363a78a6cd7632da
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15143
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update the Galileo board implementation checklist.
TEST=Build and run on Galileo Gen2
Change-Id: I1c88e9500d304273a3176d8b034a805920aab9bb
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15137
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ib674ab7ca8b6464de553a86536b1762fda98d94e
Signed-off-by: Chris Ching <chingcodes@google.com>
Reviewed-on: https://review.coreboot.org/14901
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Remove code duplication and use the common function
store_current_mrc_cache instead.
No functionality is changed.
Tested on Sandybridge Lenovo T520.
Change-Id: I4aa5463f1b1d5e1afbe44b4bfc659524d86204db
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15074
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Sometimes we need to pass board specific messages to BL31,
so that BL31 can do board specific operation based on
common code.
BRANCH=None
BUG=chrome-os-partner:51924
TEST=Build gru
Change-Id: I096878699c6e6933debdf2fb3423734f538691ae
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: af83e1b
Original-Change-Id: Ib7585ce7d3bf01d3ce53b388bf9bd60f3b65f5f1
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/349700
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15116
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
90 patches pulled in.
Change-Id: I3b893957cbd330e71d0f218262e768f577df4c66
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15122
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BRANCH=none
BUG=chrome-os-partner:52959
TEST=verified on elm-EVT SKU1/SKU2, Oak-rev5 2GB/4GB models.
Change-Id: I228c629d9a3d6cd8fc5c4e8ba24cc52d5283b4e6
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 3c19e7d
Original-Change-Id: I22356aa8d196c4c126742cfc7e85cc693acd9b39
Original-Signed-off-by: PH Hsu <ph.hsu@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/347716
Original-Commit-Ready: Yidi Lin <yidi.lin@mediatek.com>
Original-Tested-by: Yidi Lin <yidi.lin@mediatek.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15115
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
All current Oak boards have PD chips with update speeds that range from
slow (Oak) to "OMG it's so awfully slow I could make a cup of coffee and
it would still not be done" (Elm). Set the flag that enables the "Your
system is applying a critical update. Please don't turn it off." message
on EC software sync so that our users don't accidentally carry it back
to the store and demand a refund while it's still not done booting.
BRANCH=None
BUG=chrome-os-partner:51145
TEST=Booted Oak in normal mode with a new EC-RW image. Confirmed that I
saw the magic screen.
Change-Id: I000eab36d26b61b25d1f0da505f02ced15457255
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 274644b
Original-Change-Id: I64ba698985d5fbcf2b94115df72b70a5319106ac
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/348787
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15114
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The VBOOT_OPROM_MATTERS configuration option signals to vboot that the
board can skip display initialization in the normal boot path. It's name
is a left-over from a time when this could only happen by avoiding
loading the VGA option ROM on x86 devices. Now we have other
boards that can skip their native display initialization paths too, and
the effect to vboot is the same. (Really, we should rename oprom_matters
and oprom_loaded to display_skippable and display_initialized or
something, but I don't think that's worth the amount of repositories
this would need to touch.)
The only effect this still has in today's vboot is to reboot and
explicitly request display initialization for EC software sync on
VBOOT_EC_SLOW_UPDATE devices (which we haven't had yet on ARM). Still,
the vboot flag just declares the capability (for skipping display init),
and it should be set correctly regardless of whether that actually makes
a difference on a given platform (right now). This patch updates all
boards/SoCs that have a conditional path based on
display_init_required() accordingly.
BRANCH=None
BUG=chrome-os-partner:51145
TEST=Booted Oak, confirmed that there's no notable boot time impact.
Change-Id: Ic7c77dbd8356d67af7aee54e7869f9ac35241b99
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 9c242f7
Original-Change-Id: I75e5cdda2ba2d111ea50ed2c7cdf94322679f1cd
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/348786
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15113
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch adds code to initialize the two DWC3 USB
host controllers, and uses them to initialize USB3.0
on the gru rk3399 board.
BRANCH=none
BUG=chrome-os-partner:52684
TEST=boot from USB3.0 on gru/kevin rk3399 platform
Change-Id: If6a6e56f3a7c7ce8e8b098634cfc2f250a91810d
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 0306a9e
Original-Change-Id: I796fa1133510876f75873d134ea752e1b52e40a8
Original-Signed-off-by: Liangfeng Wu <wulf@rock-chips.com>
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/347524
Original-Commit-Ready: Brian Norris <briannorris@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15112
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
1. Make the xHCI driver to support xHCI controller v1.1
2. And a new function xhci_ring_doorbell(), it aims to
add a memory barrier before ringing the doorbell, to ensure
all TRB changes are written to memory.
BRANCH=none
BUG=chrome-os-partner:52684
TEST=boot from USB on Kevin rk3399 platform
Change-Id: Ife1070d1265476d0f5b88e2acf3299fc84af5832
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 0c21e92
Original-Change-Id: I4e38e04dc3c7d32ee4bb424a473c70956a3c3ea9
Original-Signed-off-by: Liangfeng Wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/346831
Original-Commit-Ready: Brian Norris <briannorris@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15111
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Not all x86 architectures support the mm register set. The default
routine that saves BIST in mm0 and a "weak" routine that saves the TSC
value in mm2:mm1. Select the Kconfig value
BOOTBLOCK_SAVE_BIST_AND_TIMESTAMP to provide a replacement routine to
save the BIST and timestamp values.
TEST=Build and run on Amenia and Galileo Gen2.
Change-Id: I8119e74664ac3522c011767d424d441cd62545ce
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15126
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Initialize the GPIOs during the boot block to properly route the SOC
UART pins.
TEST=Build and run on Galileo Gen2
Change-Id: I22c24f8c83f04566a0bbd598a141a5209569a924
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15133
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use Kconfig values to enable debug spinloops in assembly_entry.S. This
makes it easy to debug the assembly code.
TEST=Build and run on Galileo Gen2
Change-Id: Ic56bf2260b8e3181403623961874c9289f3ca945
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15135
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Conditionally add a debug spinloop to enable easy connection of JTAG
debuggers.
TEST=Build and run on Galileo Gen2 with a JTAG debugger.
Change-Id: I7a21f9e6bfb10912d06ce48447c61202553630d0
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15127
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This reverts commit 5ede3d8ccebde6f26c6b24f6458e57d99d5f3957.
No longer needed due to FSP being updated, with the 139_40 release,
to accept StackBase field
BUG=chrome-os-partner:52784
BRANCH=none
TEST=built and booted with FSP 139_40
Change-Id: Ic832d8dc4ca87631f5fef80d4d41558d9a72630a
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/15068
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
FSP 2.0 spec has updated the signatures for the FSPM and FSPS blobs
with the 139_40 release. In order to successfully pass through
memory/silicon init the header files must be updated to the latest
versions
BUG=chrome-os-partner:52784
BRANCH=none
TEST=built and booted
Change-Id: Ib60d0d9afa4ee29dff26177826ba59db81b630e8
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/15066
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Scan the boot block when building it with C_ENVIRONMENT_BOOTBLOCK
selected.
TEST=Build and run with Galileo Gen2
Change-Id: I922f761c31e95efde0975d8572c47084b91b2879
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15130
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add car_stage_entry as an optional routine in the checklist.
TEST=Build and run on Galileo Gen2
Change-Id: I52f6aefc2566beac01373dbebf3a43d35032a0df
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15129
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Support ROM_SIZE greater than 16 MiB. Work around SMBIOS rom size
limitation of 16 MiB by specifying 16 MiB as the ROM size.
TEST=Build and run on neoncity
Change-Id: I3f464599cd8a1b6482db8b9deab03126c8b92128
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15108
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Update autogenerated FSP 2.0 generic header files
based on FSP release 136_30.
Changes were made to avoid duplicating some of the
structs for every SoC.
BUG=chrome-os-partner:50765
TEST=Build coreboot
Change-Id: I6f3c9270fb67210d6ea87e17ccf52d203fa64b4b
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://chromium.devtools.intel.com/7145
Reviewed-by: Petrov, Andrey <andrey.petrov@intel.com>
Tested-by: Petrov, Andrey <andrey.petrov@intel.com>
Reviewed-on: https://chromium.devtools.intel.com/7584
Reviewed-on: https://review.coreboot.org/15081
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
EMMC TX DATA Control needs to be programmed to 0x1A1A to make amenia
system can run stable on EMMC with HS400 mode.
Change-Id: I42c23ff7e6956e75de5e1b1339a570b35d999301
Signed-off-by: Zhao, Lijian <lijian.zhao@intel.com>
Tested-by: Petrov, Andrey <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15092
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Starting from 136_30,FSP supports to update all the SDIO DLL
programming value through silicon init upd. Implement the interface
to pass board specific programming value to fsp silicon init.
Change-Id: Ifd901148f3f7f89f966217491c661ec346337c38
Signed-off-by: Zhao, Lijian <lijian.zhao@intel.com>
Reviewed-on: https://chromium.devtools.intel.com/7372
Reviewed-by: Petrov, Andrey <andrey.petrov@intel.com>
Tested-by: Petrov, Andrey <andrey.petrov@intel.com>
Reviewed-on: https://chromium.devtools.intel.com/7585
Reviewed-on: https://review.coreboot.org/15084
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Support the common Intel LPSS I2C driver for the 6 I2C bus controllers
that are present on the Skylake-LP PCH with a 120 mHz clock. The
required lpss_i2c_base_address() method is implemented separately for
verstage/romstage and ramstage environments.
This provides methods to convert to and from "struct device" and the
I2C controller bus number for that device. These are used to provide
support for the "I2C Bus Operations" that are present in the coreboot
devicetree.
To support the I2C controller before ramstage an early init function
is provided to do minimal initializaiton of the PCI device and assign
a temporary base address for use before memory. The final base
address is assigned during device enumeration and used during ramstage.
Because it is usually not necessary to enable I2C controllers before
ramstage a config register for the devicetree is provided to perform
early initialization of this controller. In addition the bus speed
can be set in the devicetree and that speed will be applied when the
device is initialized. If not provided the default speed is set to
I2C_SPEED_FAST.
This was tested with the google/chell mainboard by reading and writing
from the trackpad and codec devices during both verstage and ramstage.
Change-Id: Ia0270adfaf2843a3be4e00c732c85401a3401ef5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15105
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Allow reg_script to be used during the bootblock.
TEST=Build and run on Galileo Gen2
Change-Id: I55fe0be3f50116927b801ce67a3f23bb1931f6e7
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15131
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Don't write reserved bits in the Quark platform. Follow the previous
boot behavior and just enable SSE.
TEST=Build and run on Galileo Gen2
Change-Id: Ib3143eff02b2610b595bd666c10d70e43103ccda
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15128
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add asmlinkage to bootblock_main_with_timestamp so that it may be called
directly from the assembly code.
TEST=Build for Amenia and Galileo Gen2
Change-Id: Iefb8e5c1ddce2ec495b9272966b595d5adcebc1c
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15125
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Move the existing I2C voltage configuration variable into a new
structure that is equivalent, similar to how USB ports are configured.
This is to make room for additional I2C configuration options like
bus speed and whether to enable the bus in early boot which are coming
in a subsequent commit.
The affected mainboards are updated in this commit so it will build.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: Id2dea3df93e49000d60ddc66eb35d06cca6dd47e
Reviewed-on: https://review.coreboot.org/15104
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add the voltage tolerance GPIO attribute for configuring I2C/I2S buses
that are at 1.8V. This is currently done by passing in a value to FSP
but it is needed earlier than FSP if the I2C bus is used in verstage.
This does not remove the need for the FSP input parameter, that is
still required so FSP doesn't disable what has been set in coreboot.
The mainboards that are affected are updated in this commit.
This was tested by exercising I2C transactions to the 1.8V codec while
in verstage on the google/chell mainboard.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I93d22c2e3bc0617c87f03c37a8746e22a112cc9c
Reviewed-on: https://review.coreboot.org/15103
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Add a function similar to broadwell to set the PRR for a region of
flash and protect it from writes. This is used to secure the MRC
cache region if the SPI is write protected.
BUG=chrome-os-partner:54003
BRANCH=glados
TEST=boot on chell, verify PRR register is set and that the
MRC cache region cannot be written if the SPI is write protected.
Change-Id: I925ec9ce186f7adac327bca9c96255325b7f54ec
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Commit-Id: abb6f645f5ceef3f52bb7afd2632212ea916ff8d
Original-Change-Id: I2f90556a217b35b7c93645e41a1fcfe8070c53da
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/349274
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-on: https://review.coreboot.org/15102
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add a generic LPSS I2C driver for Intel SOCs that use the Synopsys
DesignWare I2C block and have a similar configuration of that block.
This driver is ported from the Chromium depthcharge project where it
was ported from U-Boot originally, though it looks very different now.
From depthcharge it has been modified to fit into the coreboot I2C
driver model with platform_i2c_transfer() and use coreboot semantics
throughout including the stopwatch API for timeouts.
In order for this shared driver to work the SOC must:
1) Define CONFIG_SOC_INTEL_COMMON_LPSS_I2C_CLOCK_MHZ to set the clock
speed that the I2C controller core is running at.
2) Define the lpss_i2c_base_address() function to return the base
address for the specified bus. This could be either done by looking
up the PCI device or a static table if the controllers are not PCI
devices and just have a static base address.
The driver is usable in verstage/romstage/ramstage, though it does
require early initialization of the controller to set a temporary base
address if it is used outside of ramstage.
This has been tested on Broadwell and Skylake SOCs in both pre-RAM and
ramstage environments by reading and writing both single bytes across
multiple segments as well as large blocks of data at once and with
different configured bus speeds.
While it does need specific configuration for each SOC this driver
should be able to work on all Intel SOCs currently in src/soc/intel.
Change-Id: Ibe492e53c45edb1d1745ec75e1ff66004081717e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15101
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In order to support doing bus operations on an I2C device that is
described in the devicetree there needs to be some linkage of the
device and the existing opaque I2C controller bus number.
This is provided in a similar fashion to the existing SMBUS operations
but modified to fit within the existing I2C infrastructure.
Variants of the existing I2C helper functions are provided that will
obtain the bus number that corresponds to this device by looking for
the SOC-provided I2C bus operation structure to provide a function
that will make that translation.
For example an SOC using a PCI I2C controller at 0:15.0 could use:
soc/intel/.../i2c.c:
static int i2c_dev_to_bus(struct device *dev)
{
if (dev->path.pci.devfn == PCI_DEVFN(0x15, 0))
return 0;
return -1;
}
static struct i2c_bus_operation i2c_bus_ops = {
.dev_to_bus = &i2c_dev_to_bus
}
static struct device_operations i2c_dev_ops = {
.ops_i2c_bus = &i2c_bus_ops
...
}
With an I2C device on that bus at address 0x1a described in the tree:
devicetree.cb:
device pci 15.0 on # I2C0
chip drivers/i2c/sample
device i2c 1a.0 on end
end
end
That driver can then do I2C transactions with the device object
without needing to know that the SOC-specific bus number that this
I2C device lives on is "0".
For example it could read a version value from register address 0
with a byte transaction:
drivers/i2c/sample/sample.c:
static void i2c_sample_enable(struct device *dev)
{
uint8_t ver;
if (!i2c_dev_readb(dev, 0x00, &ver))
printk(BIOS_INFO, "I2C %s version 0x02x\n", dev_path(dev), ver);
}
Change-Id: I6c41c8e0d10caabe01cc41da96382074de40e91e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15100
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Pass the serial port address to FSP using a UPD value in the MemoryInit
API.
TEST=Build and run on Galileo Gen2
Change-Id: I86449d80310b7b34ac503ebd2671a4052b080730
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15079
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch enable and configure the clocks and IOMUX for i2s audio path,
and the i2s0 clock is from CPLL.
Please refer to TRM V0.3 Part 1 Chapter 3 CRU, P126/P128/P144/P154/P155
for the i2s clock div and gate setting.
BRANCH=none
BUG=chrome-os-partner:52172
TEST=boot kevin rev1, press ctrl+u and hear the beep voice.
Change-Id: Id00baac965c8b9213270ba5516e1ca684e4304a6
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 9c58fa7
Original-Change-Id: I130a874a0400712317e5e7a8b3b10a6f04586f68
Original-Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/347526
Original-Commit-Ready: Wonjoon Lee <woojoo.lee@samsung.com>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15034
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This configures and enables SPI interface #5 used for EC
communications on Gru/Kevin.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=with the appropriate depthcharge change it is possible to trigger
booting Chrome OS from the SD card by pressing '^U' on Gru
keyboard at the right time.
Change-Id: I5304bf47e030c0b9b7794752f30ffdca6c03a4f4
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: b5cc177
Original-Change-Id: I99883daa60562ccddfaeb858c1957d497f05a501
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/346632
Reviewed-on: https://review.coreboot.org/15032
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set board GPIOs as required and add their description into the
appropriate section of the coreboot table, to make them available to
depthcharge.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=with the rest of the patches applied it is possible to use
keyboard on Gru, which indicates that the EC interrupt GPIO is
properly configured. The rest of the pins will be verified later.
Change-Id: I5818bfe855f4e7faa2114484a9b7b44c7d469727
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: e02a05f
Original-Change-Id: I82be76bbd3211179e696526a34cc842cb1987e69
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/346631
Reviewed-on: https://review.coreboot.org/15031
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
I'm not even sure how this slipped through... looks like it had never
been there in the first place. Anyway, on ARM exceptions should always
be reinitialized in all stages to make sure the handlers are still
around (especially in an OVERLAP_VERSTAGE_ROMSTAGE board like this one).
Change-Id: Ic74ea1448d63b363f2ed59d9e2529971b3d32d9a
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15099
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This defines mux settings for the GPIO bank responsible for SPI
interface #5.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=with the rest of the patches applied it is possible to
communicate with the EC on gru: pressing Ctrl-U during boot
allows to start Chrome OS from the SD card.
Change-Id: Ibc2293b5662892f7b275434f9a672ef68edf4f9e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 4f92452
Original-Change-Id: Idf55c069b05492f8cdc204a8c273e39a19a3aef3
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/346630
Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-on: https://review.coreboot.org/15030
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The same GPIOs are used on both platforms, definitions are added an a
new .h to make it easier to re-use them across the code.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=panel backlight still enabled on Gru as before. The rest of the
GPIOs are used in the upcoming patches.
Change-Id: If06f4b33720ab4bf098d23fb91322bba23fe6e90
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: c587880
Original-Change-Id: I1a6c5b5beb82ffcc5fea397e8e9ec2f183f4a7e0
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/346219
Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-on: https://review.coreboot.org/15029
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The current implementation from Vladimir simply dumps 1 MB of memory
contents starting at the base address of the second PCI device (which
most likely is the VGA controller on Intel systems). This locks up a
number of different systems, e.g. my Ibex Peak-based T410s.
This patch documents the issue and stops dumping the graphics registers
for the -a/--all parameter.
Change-Id: I581bdc63db60afaf4792bc11fbeed73aab57f63a
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/14627
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Previous FSP implementations in coreboot have included FspUpdVpd.h
directly, along with with efi headers. Instead of taking that
approach in FSP 2.0, we provide a semantic patch that, with minimal
modifications, makes FspUpdVpd.h easier to include in coreboot, and
eliminates reliance on external headers and definitions.
Change-Id: I0c2a6f7baf6fb50ae22b64e08e653cfe1aefdaf9
Signed-off-by: Alexandru Gagniuc <alexandrux.gagniuc@intel.com>
Reviewed-on: https://review.coreboot.org/13331
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Please refer Apollolake BIOS Writers Guide
Change-Id: I5f82cdc4b34a53b5184ef1e918cae15a1df6cc5e
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/15051
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I87505bb31cd1b46d27cc5c9ba8d086df7393653e
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/15050
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable virtual dev switch config.
BUG=None
TEST= On Dev FW screen, press SPACE key to boot to normal mode
Change-Id: I0fba36ed85025e4d17da106978dcc88497afee09
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/15080
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use central header file to include device address and interrupt
line to avoid confusion.
Change-Id: I9560031d9f6e12c665c8ae12f7028a67b6c8c904
Signed-off-by: Zhao, Lijian <lijian.zhao@intel.com>
Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com>
Reviewed-on: https://chromium.devtools.intel.com/7248
Tested-by: N, Harshapriya <harshapriya.n@intel.com>
Reviewed-by: Petrov, Andrey <andrey.petrov@intel.com>
Reviewed-on: https://chromium.devtools.intel.com/7580
Reviewed-by: N, Harshapriya <harshapriya.n@intel.com>
Tested-by: Petrov, Andrey <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15083
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Including the SeaBIOS bootorder file seems to be a fairly common desire,
so let's make it easy.
Change-Id: Ib0874dee46215287b09c0b52648072ef3ff06ec5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15076
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
* Add ADI vendor
Copy Intel Mohon Peak mainboard to ADI vendor. No functional changes,
only string and ifdef names changed.
Change-Id: I25a6d0ec549c79a8ff149d39f72648f625dc36fe
Signed-off-by: Chris Ching <chingcodes@google.com>
Reviewed-on: https://review.coreboot.org/14778
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
thermal.h still has references to X230 in include guard since it
seems to have been copied from that port. Code formatting changes
in romstage.c.
Change-Id: Id8bd931bed127036e8bb4ab604d9d6145f767e56
signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/15071
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Adds a label for each tool included in the cbfstool package
in order to build them more easily through Make.
Change-Id: Id1e5164240cd12d22cba18d7cc4571fbadad38af
Signed-off-by: Antonello Dettori <dettori.an@gmail.com>
Reviewed-on: https://review.coreboot.org/15075
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since the sd card cmd, data, cd lines are configured
as native mode, allow the native controller to control
the termination.
Configure SDCARD_CLK_FB which is used for calibrating the
timing of the actual clock buffer.
BUG==chrome-os-partner:53747
TEST=verify sd card detection
Change-Id: I56611826afb4fb32fefa7f1e4ba19ca4f30ba578
Signed-off-by: Abhay Kumar <abhay.kumar@intel.com>
Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/348377
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15096
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
This creates a config for the x60 audio based
on values taken from vendor bios.
The pin config is stored in (for linux 4.5 at least):
/sys/class/sound/card0/hw*/init_pin_configs
In the left column there is the pin number.
In the right column there is the default configuration of that pin.
(This has to be done while running the proprietary bios)
More information on the sound card can be found in:
/proc/asound/card0/codec#*
This also hold the information of /sys/class/sound/
What is improved:
- internal microphone is chosen by default
- when jack is inserted it is chosen instead of internal speaker
Before this had to be done manually in alsa or pulseaudio.
TEST= check if internal microphone is used by default in
pavucontrol if you are using pulseaudio.
Plug in a jack with headphones and check if there
is sound output through these and not the build-in
speaker.
Change-Id: Id3b700fd84905a72cc1f69e7d8bfa6145f231756
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/15063
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
- Put each piece of data from the printall target on its own line.
- Add a blank line between each section.
Change-Id: I50068690ab6795b7ef211865f3798c87debf2a07
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15077
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch adds asl code to include support for Google ChromeEC.
We need this to show the battery icon and notifications like charger
connect/disconnect etc.
BUG = 53096
TEST = Plug/Unplug AC Adapter multiple times and make sure the battery
connected is charging properly.
Change-Id: Id908f145789402573ea54fc4f15cf7a0e651ebf4
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/14987
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This patch adds asl code to include support for Google ChromeEC.
We need this to show the battery icon and notifications like charger
connect/disconnect etc.
BUG = 53096
TEST = Plug/Unplug AC Adapter multiple times and make sure the battery
connected is charging properly.
Change-Id: I06f48eda894418514c8ed0136500fff0efd12a35
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/15069
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add board id table as kevin/gru configuration.
BUG=chrome-os-partner:53519
BRANCH=chromeos-2016.02
TEST=check boot on Kevin board.
Change-Id: I30c16916f3cda0ac88d2ce5a922e936a405fcc89
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 16c7b5486befd73c3e31624970ba1c97e526676f
Original-Change-Id: Ib69ed9dad8e1a9e08717545c6be19a90e0298c43
Original-Signed-off-by: jongpil19.jung <jongpil19.jung@samsung.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/345736
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15028
Tested-by: build bot (Jenkins)
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add missing constants for DRAM density. This resolves boot issue,
because misconfigured density results in incorrect memory mapping.
Change-Id: I3bad911bf406bfc5677059490d0e89fcbf735b70
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15059
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Update the DDR config and DRAM driver to allow running at up to
928MHz. Kevin config/clock rate are not being changed, but Gru now
runs at 928 MHz.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=booted Kevin and Gru to Linux prompt. Ran stressapptest for 10 min on Gru,
Change-Id: I66c1a171d5c7d05b2878c7bc5eaa0d436c7a1be2
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 8baf0d82816a7ea1c4428e15caeefa2795d001f9
Original-Change-Id: I5e1d6d1025f10203da8f11afc3bbdf95f133c586
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/343984
Original-Reviewed-by: Stephen Barber <smbarber@chromium.org>
Reviewed-on: https://review.coreboot.org/15027
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fix bug introduced by merging http://review.coreboot.org/9606 and
http://review.coreboot.org/10740 in the wrong order.
Change-Id: I75dd22cd0cf30c7d91e4fa5171cb482a80eb64ca
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15070
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Correct the spelling of *firmware* in a comment.
Change-Id: I44bcd95f754ff839d582dc2150e1883a6315da9e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/15078
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Just the memory size, there is no strap to identify PCB revision.
Change-Id: I65b2f5b0ac6930bead60ea0a551f13a6bcab24c7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14997
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
fsp_notify(END_OF_FIRMWARE) should be sent to FSP to enable putting CSE
in low power state
Change-Id: I76b8e85ccf077032616ba8e4a333d9264dc65ed2
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/15054
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Because the resource for the ACPI BAR is fixed, pci_dev_set_resources
does not store it to the device. This means we need to do part of the
dance to get the ACPI IO region to work after coreboot.
Of course, this BAR can be destroyed later by the OS probing it, but
at least we try to get it working out of coreboot.
Change-Id: Ibff18d30936f94d4f149a89313254531365f43e6
Signed-off-by: Alexandru Gagniuc <alexandrux.gagniuc@intel.com>
Reviewed-on: https://review.coreboot.org/15048
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Previously, 0x0 was the value being used for an unpopulated dimm
on spd[62], however some DDR2 dimms have 0x0 as a valid value.
Now use 0xff which is an unused value even on DDR2/DDR3.
Change-Id: I55a91a6c3fe3733a7bb2abc45ca352c955c07c99
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15058
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The way dispatcher table is set up prevents linker from
optimizing unused code away, we currently have raminit in ramstage.
Optimize this manually by configuring AGESA_ENTRY booleans for
romstage and ramstage separately. This will remove references in
FuncParamsInfo and DispatchTable -arrays.
All boards now include multi-core dispatcher, it has minimal footprint:
AGESA_ENTRY_LATE_RUN_AP_TASK
ACPI S3 support depends on HAVE_ACPI_RESUME being enabled:
AGESA_ENTRY_INIT_RESUME
AGESA_ENTRY_INIT_LATE_RESTORE
AGESA_ENTRY_INIT_S3SAVE
Disabled for all boards as it was not used:
AGESA_ENTRY_INIT_GENERAL_SERVICES
Change-Id: I7ec36a5819a8e526cbeb87b04dce4227a1689285
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14417
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This adds the ISA bridge device id for the Intel C160/X99 series
chipset to the intelmetool.
Change-Id: I2e7db0fe1692985ebb167b9a44ab412a45a9f3bd
Signed-off-by: Omar Pakker <omarpakker+coreboot@gmail.com>
Reviewed-on: https://review.coreboot.org/15053
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Setting the size of the preallocated memory for the igd is done
using a cmos parameter, gfx_uma_size. This was limited to a subset of
all available sizes, that were already implemented elsewhere
in the northbridge code.
What this does is change the cmos parameter to 4 bits instead
of 3 bits to accomodate all vram sizes.
It also adds a sane default of 32mb that already was in place.
The northbridge code that reads this cmos parameter is
also changed for this new cmos settings.
352M is disabled since it causes issues on systems with 4GB or more ram.
TEST: Build, flash target. Clear cmos by corrupting
the checksum (nvramtool -c something).
Set a desired value in gfx_uma_size using nvramtool.
"dmesg | grep stolen" to see what is actually allocated.
Change-Id: Ia6479d03f1abe6d0c94bd7264365505e8f8eaeec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14900
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Follow-up on commits a5d72a3 and 53052fe for f12 and f15.
OEM Hooks are not BiosCallOuts.
Change-Id: Iab22b0d73282a5a1a5d1344397b4430c0ebb81b5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14888
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The declarations of CFG_ evaluate to correct values only when
included after the definitions of BLDCFG_ in buildOpts.c.
So we never have CFG_PLAT_NUM_IO_APICS defined here.
Change-Id: I94b3dee5a3207b37921eb24a0bcd73b5a217b2d3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14887
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The definitions of CFG_ would evaluate to incorrect values
when Options.h is included outside buildOpts.c, where all
BLDCFG_ values are defined.
Already done for f16kb.
Change-Id: I5d725b9306027c7c46c6450ab17b692fa948cf5b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14886
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I0a452b6234b02222be82ca8694868e1ffbfceaee
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14396
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ie6effa802f6971c59b5c4e07ca7d98736e27859f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14885
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Tree does not have any AGESA f10 boards. Keep the Danube platform
as a sample configuration file for unlikely future use.
Change-Id: I025aff48fcd0884b45e2a0a993d82f317ede48be
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14884
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The included file does not declare pm_ioread(), and the
modified file does not call it either.
Change-Id: I9723caf1062db23b4a3648e07c2dc4c02f862619
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14968
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
See initialize_ecc() for the awful hack that got us around cache-as-ram
being invalidated as we do ECC HW scrubbing. It once worked, but
compiler nowadays puts more registers on the stack.
Not much interest to try fix ECC for this particular board.
Change-Id: Ie6a09e28b0af5bbf2d68af72f5d98c03df33c402
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15014
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch enables eDP display by:
o. setting HPD pinmux, backlight, vdd for eDP
o. setting vop mode
o. enabling VGA configs for edid
BRANCH=none
BUG=chrome-os-partner:51537
TEST=The dev screen is shown on kevin board
Change-Id: If8b07307454daa88727d317cc208d6c97de07ad7
Signed-off-by: Martin Roth <martinroth@google.com>
Original-Commit-Id: b1ad9337510f5437f691153dc68883edf273e4c7
Original-Change-Id: Id7006619b5be638b286a5402d892a5361ac1e430
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/340026
Original-Reviewed-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-on: https://review.coreboot.org/14858
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch adds functions to init the display. To set up the display,
initialize the eDP and read the EDID. Based on these, we then
set the clock for VOP, and finally enable VOP and backlight.
For a mainboard, it should set the vop_id, vop_mode and
framebuffer_bits_per_pixel in devicetree.cb.
For VOP_MODE_AUTO_DETECT, it will try eDP first and then
HDMI (which is not supported yet).
EDIT: Updated Makefile to only build in new files if
MAINBOARD_DO_NATIVE_VGA_INIT is enabled. All of these
platforms should have it enabled, so this shouldn't make
any difference except now, before the platform code is
in place.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=test with the other patch
Change-Id: If935415026c945ab6ee128bd6bbdd792890aa24a
Signed-off-by: Martin Roth <martinroth@google.com>
Original-Commit-Id: c1020cc806775629f4d5dc57bd805a9a12169386
Original-Change-Id: Ic32d0a251cb8e08aa5f0b15b2c06c4e02c08a761
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/342336
Original-Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/14857
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Now that there is a better way of finding optional routines, make the
weak routines quiet so that it may be used for the optional
implementation.
TEST=Build and run on Galileo Gen2
Change-Id: Ic58c7de216394f80aee3a78dd08bd4682783be42
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15043
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Select CREATE_BOARD_CHECKLIST to create the checklist for the Quark SOC
and Galileo board.
TEST=Build and run on Galileo Gen2.
Change-Id: Ieb3e9a5a4c149cf160e11d44a515591b57fe5c83
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15004
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Build the <board>_checklist.html file which contains a checklist table
for each stage of coreboot. This processing builds a set of implemented
(done) routines which are marked green in the table. The remaining
required routines (work-to-do) are marked red in the table and the
optional routines are marked yellow in the table. The table heading
for each stage contains a completion percentage in terms of count of
routines (done .vs. required).
Add some Kconfig values:
* CREATE_BOARD_CHECKLIST - When selected creates the checklist file
* MAKE_CHECKLIST_PUBLIC - Copies the checklist file into the
Documenation directory
* CHECKLIST_DATA_FILE_LOCATION - Location of the checklist data files:
* <stage>_complete.dat - Lists all of the weak routines
* <stage>_optional.dat - Lists weak routines which may be optionally
implemented
TEST=Build with Galileo Gen2.
Change-Id: Ie056f8bb6d45ff7f3bc6390b5630b5063f54c527
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15011
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Return the correct board version in SMBIOS.
TEST=Build and run on Galileo Gen2
Change-Id: I97ec7bcd475142eb90930152da0244a3c5d09634
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15041
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The Chrome OS bootloader is changing its EC software sync mechanism to
look for the hash of an EC image in a separate CBFS file, rather than
using the CBFS hash attribute of the image itself (see
http://crosreview.com/348061). This patch makes coreboot generate
appropriate hash files for the new format when it builds and bundles a
Chrome EC image. This also allows us to compress the EC image itself.
Change-Id: I9aee6b8d24cdf41cb540db86a7569038fc7d9937
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15039
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
These files do not use definitions from OptionsIds.h. Also those
definitions are required and already included for Ids.h.
Change-Id: I149fcfe2ad72fe3d7390ee2043a86432aeae3f08
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14980
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
i2c_init() leaves the I2C device enabled. Combined with the default
interrupt mask (0x8ff) and the fact that the interrupt line is shared,
this leads to an interrupt storm in the OS until a proper I2C driver
is loaded.
This change clears the interrupt mask to prevent the interrupt storm.
Change-Id: I0424a00753d06e26639750f065a7a08a710bfaba
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Reviewed-on: https://review.coreboot.org/15047
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
TSEG register comes out of reset with a non-zero default value. This
causes issues when cbmem_top returns non-zero value based on TSEG read
before DRAM is initialized. Thus, clear TSEG reg early in bootblock to
avoid unwanted side-effects.
Change-Id: Id3c6c270774108e4caf56e2a07c5072edc65bb58
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15049
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Verstage on apollolake requires the functions defined in car.c to
perform flush of l1d to l2 on loading romstage into CAR.
Change-Id: I6d9a0b9dfb58c2126ad70172846e90663e588857
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15046
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Modern platforms like Apollolake do not use XIP for early stages. In
such cases, cbfs_prog_stage_load should check for NO_XIP_EARLY_STAGES
instead of relying on ARCH_X86 to decide if a stage is XIP.
Change-Id: I1729ce82b5f678ce8c37256090fcf353cc22b1ec
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15045
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I714af8ab552dc1923a1b64e0c502d6c7b96dd444
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15044
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The eSATA port of Lenovo T420 is port 3. I've checked it on an iGPU
model and a dGPU model.
Change-Id: I64bcc887140c1634dd1475d29e97780a5128d0be
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/14632
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
|
|
Update the weak functions for the MRC cache.
TEST=Build and run on Galileo Gen2
Change-Id: I54a1252cfff1a2f68b163f0feb65e2bceb37f6a9
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15042
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
