| Age | Commit message (Collapse) | Author |
|---|
|
The binary does change on these with BUILD_TIMELESS.
Change-Id: I45d51d53f991556cedd1cc45997d76fc828bceb5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74544
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
VMX is enabled through a bit in the IA32_FEATURE_CONTROL MSR, which can
be locked. The MSR remains locked after a non-power cycle reset, though.
If the MSR is locked, coreboot bails out and leaves VMX in the state it
was found. Because of this, changes to the VMX enable option in the BMC
only take effect after the system is power cycled.
This behaviour is highly undesirable because users are likely not aware
that a power cycle is required for changes to VMX state to take effect.
So, if VMX is supported, the IA32_FEATURE_CONTROL MSR is locked and the
current VMX state does not match the requested state, then issue a full
reset. This will power cycle the system and unlock the MSR, so that the
desired VMX state can be programmed into the MSR. This is checked early
to avoid needlessly doing time-consuming operations (running FSP) twice
if we know we will need to power cycle the system anyway.
Note that a user may change the VMX setting after the newly-added check
but before the setting is read in ramstage to program the MSR, but this
is a non-issue as firmware settings need a reset to take effect anyway.
TEST: Toggle VMX setting in BMC and reboot without power cycle, observe
coreboot automatically issues a power cycle reset because the MSR
is locked and the VMX state differs. Verify that the system boots
properly with VMX in the correct state after having power cycled.
Change-Id: Id9061ba896a7062da45a86fb26eeb58927184dcb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Instead of having the maximum number of possible CPU objects defined in
the DSDT, dynamically generate the number of needed CPU devices in the
SSDT like it's done on all other x86 platforms in coreboot.
TEST=APU2 still boots and Linux doesn't show any ACPI errors with this
patch applied and it prints "ACPI: \_SB_.P000: Found 2 idle states".
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id6f057ad130a27b371722fa66ce0a982afc43c6c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73073
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Instead of having binaryPI generate a PSTATE SSDT that uses \_PR_ as the
scope for the CPU objects and patching this SSDT in coreboot to use the
\_SB_ scope in patch_ssdt_processor_scope, request binaryPI to use the
\_SB_ scope instead by setting the late platform configuration option
ProcessorScopeInSb to true.
TEST=APU2 still boots and Linux doesn't show any ACPI errors with this
patch applied and it prints "ACPI: \_SB_.P000: Found 2 idle states".
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I411201b55cfee30ae41da4e6814679bdb49e9bf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73386
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Ic2efbb1d2a13212921ad110314a6394a4dca6a8a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I62b7390c2de244cce169550e9b1fa41af738525d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75037
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I1c995d942fa25a9268fbf716034335937df57714
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75036
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
This fixes clang warnings.
Change-Id: I407da6ec05ef646f61bd81e314fee1b5ea659192
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74557
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
TEST: BUILD_TIMELESS=1 remains the same.
Change-Id: Id2cb37dbe4d450fe7f91a527b5cd73ac55863548
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74542
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
The `get_board_settings()` function always returns non-NULL, so there is
no need for NULL checks. When only one member is accessed, also drop the
local variable and directly dereference the function's return value.
Change-Id: I4fc62ca2454f4da7c8ade506064a7b0e6ba48749
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75140
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
1. Restore the reverted 'commit 059902882ce5 ("drivers/ocp/ewl: Add EWL
driver for EWL type 3 error handling")'.
2. Print more EWL type 3 error information when it occurs.
Change-Id: Ib83b7653a839d18a065b929127549acd10bce7a7
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jon.zhixiong.zhang@gmail.com>
|
|
This mainboard contains in addition to its base variant, mc_ehl2, an LCD
panel driven through the PTN3460 eDP-to-LVDS bridge.
This patch enables the PTN3460 support by adding the device to
devicetree.cb and board-specific configuration parameters in
lcd_panel.c.
BUG=none
TEST=Boot with the LCD panel attached and observe whether the picture is
stable and free of artifacts coming from wrong resolution and timing.
Change-Id: I196d7ceeb7ac241c9b95db2ef791a5f3ff7890a7
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard is based on mc_ehl2. In a first step, it contains a copy
of mc_ehl2 directory with minimum changes. Special adaptations for
mc_ehl5 mainboard will follow in separate commits.
Change-Id: Id80f8eb49dd2fed0ed1ffc479d47d8669eca84c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Based on touchscreen product spec.
For uldren variants with a touchscreen, drive the enable GPIO high
starting in romstage while holding in reset, then disable the reset
GPIO in ramstage (done in the baseboard).
BUG=b:279989974
TEST=Build and boot to OS in uldren. Touch screen is workable.
Change-Id: Ib1b1ce80aa1dd8c312e3663fc50c9e9f53cc07fe
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74835
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Replace `memupd->FspmConfig.` with `mcfg->` for the sake of brevity.
Change-Id: If2e7cccca955b0c1e07c1ecf100d29a923107856
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75136
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
|
|
This signal isn't functionally being used and is causing leakage
during suspend. Set it to NC.
BUG=b:279762779
TEST=builds. WWAN functional.
Change-Id: I93f2b0a781e250678280b57e4ab1d80ef27ff460
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
The patch defines enum type for MKHI group IDs and ME SKU types instead
of macros.
TEST=Build code for Rex
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I102e802938a6a664a43a362d90a26755cff8f316
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Harsha B R <harsha.b.r@intel.com>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
|
|
Having `_cmos_offset` in a CMOS offset is superfluous; remove it
so the CMOS entry is just `ramtop`.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ibc1e7d78d2e3ae04330d19e64c3437ff07060ea8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
If reading the serial/part number fails, returning an empty string is
very confusing. Instead, return "INVALID" to make problems obvious.
Change-Id: I3c174ca76d51b44456c7b68f4fcffb4c8f9379be
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
|
|
The Realtek RTL8111F NIC is currently not defined at all, nor as a child
device, resulting in the on_board flag not being set to 1. This means
that Linux / udev will call the device enp3s0 rather than eno0, as it's
appropriate for on-board ethernet devices.
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Change-Id: I95f01a466a59234d1cbe2420f208bf58ae28fcc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This board has a TPM connector, enable support for it.
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Change-Id: I1861df95eef15bc2bd29412240d61456eaaad8c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75105
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Small typo in brask/gma-mainboards-ads
Should be brask/gma-mainboards.ads
BUG=b:277861633
BRANCH=firmware-brya-14505.B
TEST=Builds
Change-Id: I9800870dcef13a3e16f6235137e79234a5e6bf83
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75052
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add the acpigen_resource_io helper function to generate an I/O range
resource.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I177f59b52d4dbbff0a3ceeef5fc8c7455cef9ff8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
|
|
Add the acpigen_resource_bus_number helper function to generate a bus
number range resource.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ib1f1da3dbe823c6bc4fc30c0622653410cfbf301
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
|
|
Adds the option to set the 'DmaProperty' in the device's _DSD.
This can be done by setting "add_acpi_dma_property"="true". If not set
(or set to false), the device descriptor generation behavior will remain
unchanged. The naming convention for the config option was chosen to
match that of other drivers.
This partially reverts commit 5609f7a684c6 ("drivers/pcie/generic: Clean
up driver") as the driver is now used on a couple mainboards which need
the DmaProperty.
Change-Id: I996fe4923948d13a20bf8b6b1a93dab0866d0fd4
Signed-off-by: Mark Hasemeyer <markhas@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
In GEN_PMCON1 (Offset 1020h), Bit 0 is the "After G3 Enable" (ag3e)
(source Intel document #569262). Only use 8 bits, in the same way as
most other Intel SOCs do, for pmc_soc_set_afterg3_en.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Idb290d1480b03cb3425edc6ff29b9c78a6545df1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74955
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
reStructuredText grid tables require row separators otherwise the rows
get concatenated into a single cell for each column.
Representative output of previous behavior:
```eval_rst
+-------------------------+-------------------+------------+----------+
| Vendor/Board | Processor | Date added | Brd type |
+=========================+===================+============+==========+
| 51nb/x210 | INTEL_KABYLAKE | 2020-03-16 | laptop |
| acer/aspire_vn7_572g | INTEL_SKYLAKE | 2022-01-28 | laptop |
| acer/g43t-am3 | INTEL_X4X | 2020-09-28 | desktop |
+-------------------------+-------------------+------------+----------+
```
Representative output of corrected behavior:
```eval_rst
+-------------------------+-------------------+------------+----------+
| Vendor/Board | Processor | Date added | Brd type |
+=========================+===================+============+==========+
| 51nb/x210 | INTEL_KABYLAKE | 2020-03-16 | laptop |
+-------------------------+-------------------+------------+----------+
| acer/aspire_vn7_572g | INTEL_SKYLAKE | 2022-01-28 | laptop |
+-------------------------+-------------------+------------+----------+
| acer/g43t-am3 | INTEL_X4X | 2020-09-28 | desktop |
+-------------------------+-------------------+------------+----------+
```
Change-Id: I83be58dd2c34c65ae2c65cf2bd98330936fb6f6a
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Create the gothrax variant of the nissa reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.).
BUG=279614675
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_GOTHRAX
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: I129e4a55e4b87091e425a45392024d04f3977c79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74748
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
The boxy removed the APW8738BQBI-TRG and
"disable_external_bypass_vr" should be set to "1" to disable
BUG=b:271407334
TEST=emerge-dedede coreboot
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: Ic6667e93de41e84f67363ab7554fe755fe50684a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74889
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create overridetree and GPIO config based on latest schematic:
1. Update PCIe ports
2. Update USB ports
3. Remove unused I2Cs
4. Remove unused peripherals (SD card, eDP, speakers)
5. Add LAN
6. Thermal policy for updated temp sensors
BUG=b:277529068
BRANCH=dedede
TEST=build
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: I5a155ebca50dbd5bdb046713ebabbee395361273
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74626
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
The return value of cse_get_bp_info() is an enum integer, where zero
means success and non-zero means failure. The function
store_cse_rw_fw_version() calls the function cse_get_bp_info() and
validates the return value as a boolean causing prematurely returns of
the parent API even if cse_get_bp_info() is successful.
This patch corrects this logical error by returning only if
cse_get_bp_info() fails.
TEST=Build and boot google/nivviks and verify that the ISH version info
command is only being sent during cold boot.
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Change-Id: Ice278e5ac69ff2f2c9f1936b76d71ae9deb6f855
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74998
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
|
|
At present coreboot_rsdp remains unset for QEMU, which results in
an incomplete LB_TAG_ACPI_RSDP coreboot table generated.
Fix this by assigning coreboot_rsdp properly.
TEST=Build coreboot for QEMU x86 i440fx (default) with U-Boot x86
as the payload, boot coreboot.rom with QEMU, and run 'acpi list'
from U-Boot shell to show the ACPI tables.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Change-Id: I5bc3f0528d4431fd388ca52b8865f9be0e1faf92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
|
|
For the sequenced controlled shutdown path, there's a 10ms delay
after the PEXVDD rail is disabled to permit discharge needed on
Agah/Proxima.
This can be dropped to 3ms for Hades designs Proto0 and forward.
Once Agah board is dropped, "if CONFIG" can be cleaned up/removed.
BUG=b:271167335
TEST=builds
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: I8a0d62ec76caff861adce2d6c0ba2d4e4064affa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75051
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With the introduction of a new Linux version a problem has appeared
after a software initiated reset via CF9h register. The problem
manifests itself in the fact that the Linux kernel does not start after
the reboot. The problem is solved by setting bit 3 to 1 in Reset Control
Register (I/O port CF9h). This leads to the fact that the PCH will drive
SLP_S3 active low in the reset sequence. It leads to the same behavior
as in commit 04ea73ee78bc ("siemens/mc_apl3: Set Full Reset Bit into
Reset Control Register") explained.
Change-Id: Ia8b7f997ca6234add569da751e1070144790e258
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I6578aee52e6900b25441dc119383856acc480231
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
An underscore has crept into the mainboard model option for mc_ehl3 and
mc_ehl4 by mistake. This patch fixes the incorrect entry.
Change-Id: Ie59619877fb6341a5bbfe91c13e7692943480ad0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75040
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are only SSD connected to SATA ports on this mainboard. To prevent
misbehavior, set the correct hard drive type for enabled SATA ports.
BUG=none
TEST=Boot into OS and check the stability of the SSD
Change-Id: I116b1e36f0582956604c3c2508961ffb3de0898a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74947
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
- VBT information: The link from 01.org is dead, but appears to have
been identical to the i915 page in the Linux kernel docs based on
snapshots on archive.org.
- Cgit: coreboot no longer has cgit running for the repos it hosts,
and these links redirect to the Gitiles list of repos hosted on
review.coreboot.org. Based on snapshots on archive.org, these used
to link to the individual repo or tree. Replace these with an
equivalent Gitiles link.
Change-Id: Id0bfee7b806c851fbe1dcf357e14d9b593e8569a
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
|
|
If the ME is disabled with the `me_state` CMOS setting, boot
times are approximately 5 seconds longer:
942:before sending EOP to ME 1,240,773 (5,599)
943:after sending EOP to ME 6,263,951 (5,023,177)
Total Time: 6,167,443
This is because the current code only checks if the ME is
disabled for CSE LITE SKUs. With this patch, boot times are
approximately 5 seconds quicker:
Total Time: 1,143,932
Tested on `starbook/adl` and `starbook/tgl`.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I182f30d4fbf43955747c6a7a0b284a43f9c5e4ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
R680E, Q670E, H610E are the ADL-S IoT variants
see also:
commit a0bc90e4abfe ("Add missing ADL-S device identification")
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I1dbfa0464bc22f9bcf91d9e9fa9eb79132600175
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Update header files for FSP for Meteor Lake platform to version 3165_81, previous version being 3084_85.
FSPM:
1. Change UPD name from 'GtExtraTurboVoltage' to 'GtAdaptiveVoltage'
2. Change UPD name from 'CoreVoltageAdaptive' to 'CoreAdaptiveVoltage'
3. Change UPD name from 'RingVoltageAdaptive' to 'RingAdaptiveVoltage'
4. Address offset changes
FSPS:
1. Remove deprecated UPD 'PcieDpc'
2. Address offset changes
BUG=b:280005256
TEST=Able to build and boot google/rex to ChromeOS.
Signed-off-by: Kilari Raasi <kilari.raasi@intel.com>
Change-Id: I67939ecf71166fca4f3d2d6cd4622215bebc5718
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This fixes an issue where pcie was not power gating and blocked
S0ix entry. Overwrite pcie max non-snoop and snoop latency tolerance
values to 15.73ms as stated in doc #729123 - MTL External Design
Specification.
BUG=none
TEST=Boot google/rex, print/check values.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.corp-partner.google.com>
Change-Id: I9dfb9edbac95d28d50653777466ea172be64f612
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68308
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on feedback and experiences from new coreboot users, it isn't
clear that Tutorial 1 is mainly intended to set up the toolchain and
will not produce a bootable ROM for their board. Thus, add a note
explicitly mentioning this with a short explanation.
The process of manually building and adding the payload is also unusual,
since payloads are usually handled automatically by the build system.
This adds a note in the summary to provide an explanation of this.
The savedefconfig output is also outdated, as Kconfig now outputs
additional lines (even though many of those are the same as the
defaults). This has caused confusion, leading users to think that they
may have configured coreboot incorrectly. Update this to the current
defconfig contents and add a note that this may change depending on the
coreboot version.
Change-Id: I13206aa05a425ddfe33ee35feff0db490585a59f
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73816
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ibb680bb8f94fb8a2812f420ac38f15684b5c0b4f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Change-Id: I20a66dce1612ab4394c26f9b0943dac14bcdcfc4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
The Linux kernel recently updated the wording of their sign-off
procedure, changing the ambiguous "real name" requirement to "a known
identity" and dropping "no pseudonyms". Anonymous contributions remain
uncommittable [1]. As discussed in the April 19, 2023 leadership
meeting, update our policy to go along with Linux and flashrom (who also
updated their policy).
[1] Linux kernel commit d4563201f3
(Documentation: simplify and clarify DCO contribution example language)
Change-Id: Ie676334f7c1509524adcb8dbb78495fb4da35ede
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Currently, this only exists on the old wiki and the developers.html page
on coreboot.org, but it really ought to be somewhere in the new docs
alongside the other contribution guidelines. This was largely copied
from the text from the developers.html page.
Change-Id: If50b3827ab36234719f9a90239caec4612eb6762
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74825
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
The Intel SoC Meteor Lake requires a higher pcie max non-snoop and
snoop latency tolerance. Add config to let SoC overwrite the common
code settings if needed.
BUG=none
TEST=Boot google/rex and print/check if able to overwrite values.
Change-Id: Ic2b9a158d219e6c6e7f6e7f0ae0f093c1183b402
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Intel's EHL FSP offers the possibility to select the connected hard
drive type to SATA ports. One has the option to choose between HDD ('0'
- default) and SSD ('1').
This patch provides a chip config so that this FSP parameter can be set
as needed in the devicetree on mainboard level.
Change-Id: Idb03aff5b6c5df592b47e2f4abe4fe58ac7151ba
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74946
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Follow the EC GPIO programming sequence to enable the MXM PCIe slot.
Change-Id: I75d7ac488bb005751e6f674ab9a2fd99baad571b
Signed-off-by: Anand Vaikar <a.vaikar2021@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
All other boards use MAINBOARD_ prefix instead of board name.
Change-Id: I97d9d28963c97e780156d75b39deac069028866a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Processing LD flags is done without most warnings enabled, which is why
this never caused problems.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ic9d82c1426a1c1d2f21c8e7560685cf9d7106a88
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75033
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4d34e5c094440dad4a6ab9adc67d3da6b71ac2bf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74514
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Change-Id: If4b7c2b94e0fec84831740336ccdbea0922ffbfe
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74513
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name.
Change-Id: I2ae03a3ac548674b8c5e7dfaff47d6c536b452f1
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75013
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I27a610255e5680be1b507d45c6695cf9419ee052
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Change-Id: I3881c152663a038833d8126d7f24f2a6688426d1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74515
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Assigning duty_offset while duty_width==0 has no purpose.
Under intel/common/block, previous assignment for fadt->gpe0_blk
resolves GPE0_STS(0) from xeon_sp/ebg/.../soc_pm.h and also assigns
value matching pmbase + 0x60.
Change-Id: Iaf688d9471ac527ac20307cf16216abdab731a06
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74827
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The STA_HIMAX83102_J02 and STA_ILI9882T panel will be used for Starmie,
enable these two panels config for it.
BUG=b:272425116
BRANCH=corsola
TEST=build starmie and check the cbfs include the panels
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I1dd696dd6a84d9606e4b9a2d4884dd70a6df9161
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74200
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add STA_ILI9882T panel serializable data to CBFS.
The panel datasheet: ILI9882T_Datasheet_20220428.pdf
BUG=b:275470328
BRANCH=corsola
TEST=build and check the CBFS include the panel
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Ia7a37c0659f0959fe7be01aba0f08d63119d139f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
|
|
This reverts commit d6e0a90aa0bd574b28b6c9b4b46289bf46a208db.
Reason for revert: Not ready to land, blocked by ancestor CL
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ic14e17db4aed2f998878920c66cdc16362920dcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75050
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the CMOS bank I/O base addresses with
PC_CMOS_BASE_PORT_BANK* rather than hard-coding as 0x70, 0x72. The
defaults remain the same.
Change-Id: Ie44e5f5191c66f44e2df8ea0ff58a860be88bfcf
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74903
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CMOS defaults greater than 128 bytes long will extend to bank 1.
Change-Id: I9ee8364d01dd8520be101de3f83d2302d50c7283
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
FSP-M is normally memmapped and then decompressed. The SPI DMA
controller can actually read faster than mmap. So by reading the
contents into a buffer and then decompressing we reduce boot time.
It is interesting that FSP-M takes an additional 8ms to execute. I
suspect since we call it 50ms earlier it's having to wait for one of
its dependencies.
BUG=b:179699789
TEST=Boot guybrush and see 30ms reduction in boot time
| 970 - loading FSP-M | 0.316 | 0.997 Δ( 0.68, 0.05%) |
| 17 - starting LZ4 decompress (ignore for x86) | 0.026 | 13.874 Δ( 13.85, 0.96%) |
| 18 - finished LZ4 decompress (ignore for x86) | 64.361 | 0.337 Δ(-64.02, -4.43%) |
| 2 - before RAM initialization | 0.534 | 0.529 Δ( -0.01, -0.00%) |
| 950 - calling FspMemoryInit | 1.455 | 1.132 Δ( -0.32, -0.02%) |
| 951 - returning from FspMemoryInit | 207.695 | 216.537 Δ( 8.84, 0.61%) |
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I850b1576501753a355e7b23745e04802a0560387
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Librem Mini v1/v2 has an automatic power-on setting provided by the EC
in BRAM bank 1. Use this bank as the high bank of CMOS memory so that
setting can be described in cmos.layout.
Change-Id: Icb87bc521f71aa4350c8f5a64fc2cbe7a7a8c808
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Beware that there's no XHCI2 controller and the USB4 controller device
pointers were added right after the xhci_0 and xhci_1 controller device
pointers.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I14725d4b546ffcca42e21bbe7756babaaff8fea3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74658
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Introduce acpigen_write_BBN to generate the ACPI method object that
returns the base bus number for a PCI(e) host bridge. When called, the
base_bus_number argument must be the first PCI bus number that got
assigned to the corresponding host bridge.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib67bf42b9c77c262d8a02d8f28ac5cb8482136b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
|
|
Add STA_HIMAX83102_J02 panel serializable data to CBFS.
The panel datasheet: HX83102-J02_Datasheet_v03.pdf.
BUG=b:272425116
BRANCH=corsola
TEST=build and check the CBFS include the panel
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I382bdc89e5a217fd1c28e677938f454dc09725cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
There are 2 regex patterns defined to process the lines from *fw.cfg:
1) for lines with mandatory entries
2) for lines with mandatory + optional entries
Consolidate the regex pattern. Add enums for matching regex caller
groups so that the human readable group IDs can be used instead of magic
numbers.
BUG=None
TEST=Build Skyrim BIOS which only have mandatory entries. Build Guybrush
BIOS image which have both mandatory and optional entries. Confirm that
the amdfw.rom built before and after this change have matching SHA in
both Skyrim and Guybrush images. This ensures that the optional level
entries in Guybrush are handled as expected. Boot to OS in Skyrim.
Change-Id: I7289ddbbec4d5daefe64f59b687ba3a4af46d052
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Add FW_CONFIG item for FP sensor init and conditionally init
the GPIOs based on whether we're using a SPI or UART FP sensor.
BUG=b:276939271
TEST=builds
Change-Id: I9815bd17df1d15f73529beb15d08cde1ef90efad
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add FW_CONFIG item for eMMC/NVMe support and address the init
of the lanes based on said config.
BUG=b:278877257
TEST=builds
Change-Id: Id6452f497cf78549b7d6126f1b55cd6d45b403c3
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74957
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Mark Hasemeyer <markhas@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
For early Sign of Life to work, we may need certain pin configurations
very early in boot (e.g. HDMI). This may happen before romstage GPIOs
are configured, and bootblock is not suitable for field upgrading
existing devices. Add a separate GPIO table that can be configured
when early graphics is invoked.
BUG=b:277861633
BRANCH=firmware-brya-14505.B
TEST=Builds and SoL functions on HDMI enabled variants
Change-Id: I7b3ce96a4166451e72aa70b3086eff3fb8b082b7
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Allow different gma-mainboards configs for different baseboards
as they support varying display interfaces. Set Brya to eDP only
and Brask to HDMI only.
BUG=b:277861633
BRANCH=firmware-brya-14505.B
TEST=Builds and SoL functions on both brya and brask varaints
Change-Id: Iaf3f35b009d53e50723e4aa82c0f4932783f9bb9
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Denote the correct value of ACPI _PLD for USB ports.
The horizontal position of port C0 is incorrectly labelled.
+----------------+
| |
| Screen |
| |
+----------------+
C0 | | A0
| | C1
| |
+----------------+
BUG=b:216490477
TEST=emerg-rex coreboot
Signed-off-by: Won Chung <wonchung@google.com>
Change-Id: Id9ed435ca0af131e3bb4538701fc97d78146899f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74366
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add _PLD support to GFX device so that each display output can store
its physical location of connection point. This is to be used primarily
for describing DP on USB-C ports in the future patches.
The upstream Linux kernel now has a feature to compare _PLD of Type C
connectors and DP connectors to link them together.
https://cgit.freedesktop.org/drm/drm-misc/commit/?id=c5c51b2420625faa1f0e363f21dba1de53806ff7
This feature allows us to tell which display output is used by which
USB-C port.
So, for the future boards, we want to add _PLD for each DP connector
matching with the corresponding USB-C port.
BUG=b:277629750
TEST=emerge-${BOARD} coreboot
Signed-off-by: Won Chung <wonchung@google.com>
Change-Id: I393207746a9e82c1fd7622ab3661d7b1232cb62f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch adds some of the variety of configuration options exported
by the Pericom Inc. PI7C9X2G608GP PCIe switch over its SMBus interface.
Currently implemented options are only used to adjust the switch
upstream port amplitude and de-emphasis levels in millivolts. Only
values specified in the switch datasheet (in tables 6-6 and 6-8) are
allowed.
Example of a devicetree.cb entry:
chip drivers/i2c/pi608gp
register "gen2_3p5_enable" = "true"
register "gen2_3p5_amp" = "AMP_LVL_MV(425)"
register "gen2_3p5_deemph" = \
"DEEMPH_LVL_MV(37, 5)"
device i2c 0x6f on
ops pi608gp_ops
end
end
Link to the datasheet:
https://web.archive.org/web/20210225074853/https://www.diodes.com/assets/Datasheets/PI7C9X2G608GP.pdf
BUG=none
TEST=Create devicetree.cb and Kconfig entries for this driver
in a mainboard containing the switch and verify, that the values read
out from the switch config space match the values programmed over the
SMBus.
Change-Id: Id191c4e97b99da58efd3ba38bf8cca3603ece4d5
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Update eMMC DLL settings based on Uldren board.
BUG=b:280120229
TEST=executed 10 cycles of cold boot successfully
Change-Id: I46e2f9df0e82e66fa3ae32aa87b4bcf30d5737ab
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Update devicetree to support G7500 touchscreen.
BUG=b:273791621
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot and check touchscreen function
Change-Id: I3b63b1bb45275ad7eef8799dcff27f264739c258
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: Id5b0fa96ca8d86ddf20d808f5107a43ad2d0a1e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Return 0xf from PCI0 _STA method so that bit 2 is set which indicates
that the device should be shown in the user interface. This ports commit
c259d7192806 ("soc/amd/stoney/acpi: Unhide PCI0 root device from OS")
back from Stoneyridge.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5e724292431be7f7c2a0b6678b426831e3c19154
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74990
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Return 0xf from PCI0 _STA method so that bit 2 is set which indicates
that the device should be shown in the user interface. This ports commit
c259d7192806 ("soc/amd/stoney/acpi: Unhide PCI0 root device from OS")
forward from Stoneyridge to the newer AMD SoCs.
TEST=On Mandolin the PCI Express Root Complex now shows up in the device
manager on Windows 10 and when switching the view to 'devices by
connection', all PCI(e) devices are shown below it.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4155556dc5df8f163fe06aa6719fadbb2684cc19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74949
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch ensures that the PRERAM_CBMEM_CONSOLE_SIZE and
CONSOLE_CBMEM_BUFFER_SIZE hold a larger cbmem buffer size to contain
the entire FSP debug serial log.
The existing implementation was not appropriate, where the larger cbmem
size was even applicable for serial AP firmware (w/o FSP debug) image
as well.
This change is necessary to ensure that the FSP debug serial log is
always available, even in cases where the cbmem buffer size is
limited.
BUG=b:280481298
TEST=Able to build and boot google/rex with non-FSP serial AP image
and with FSP serial AP image. Able to see the AP log completely inside
the cbmem.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib35780fd558c8b6d9aa2e17241131ea4a58c2b9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
While Chromebook hardware originally would not have the
capacity to do suspend-to-disk (ACPI S4), the power management
code in EC should react to S4 request as if it was S5 request.
Change-Id: Ida9118919c8149d94f470847d0c4aad9c0b97d3e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
No longer needed, this was used with old SMM relocate code.
Change-Id: I7c913e10eb965419c7d2ddede744f8140a5b7976
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I7655de5a8fcd5ac5c820938059bbb8b1ad877db7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
To select COMMON_SMM should not imply COMMON_PMBASE, it's
really a depencency. Select them both explicitly for i82801dx.
Change-Id: I387ade9cfd38b6555ed9e37c1b9178a6da2d7260
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I0ada381883aa65d36434486dcce6b2331599e5c3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I47ec05aa87e4e7c02b19817b2f703eca492008e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch makes CSE sync in romstage default enabled unless ramstage
config (SOC_INTEL_CSE_LITE_SYNC_IN_RAMSTAGE) chooses to override it.
TEST=Able to build google/marasov with this change where CSE sync is
performed early inside romstage.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3f5017fbcf917201eaf8233089050bd31c3d1917
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Add DDR DQ map config for screebo
BUG=b:276814951,b:272218757
TEST=emerge-rex coreboot
Change-Id: I993ae4024689b9cedbea247689a760bd83cd0d45
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74961
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Add variant makefile to support including the memory folder for Myst.
BUG=b:273383819
TEST=Builds in chromium with blobs
Change-Id: I03b0cd91dd66f357b15522da36f5118867b6b14c
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74964
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the OEM ID from CBI to determine the correct OEM board name.
ID mapping taken from ChromeEC source, branch firmware-fizz-10139.B.
TEST=build/boot multiple fizz variants, check that board name reported
correctly in SMBIOS tables.
Change-Id: I06251974ac73570b911920ed566a175e8e733710
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Override SMBIOS product name with sub-variant name based on board SKU.
TEST=build/boot multiple nami variants, verify SMBIOS product name
reports correctly.
Change-Id: I2125bfb6436469405378f9c983d7cfcb2f85f916
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
DSM (Dynamic Speaker Management) uses calibration parameters stored in
a VPD (Vital Product Data) FMAP region to configure the audio output
via an ACPI _DSD table. This has no dependency on a ChromeOS, and can
be used by Linux/Windows drivers if appropriately configured.
Remove the dependency of DSM_CALIB (and the calibration file) on
CHROMEOS and replace it with VPD, so that non-CHROMEOS builds
can utilize this feature as well. Move files from underneath
vc/google/chromeos to underscore the point.
TEST=build/boot google/nightfury, dump ACPI, verify DSM calibraton
parameters present in _DSD table.
Change-Id: I643b3581bcc662befc9e30736dae806f94b055af
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74812
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Only expand these strings in lib/identity.o.
Change-Id: I8732bbeff8cf8a757bf32fdb615b1d0f97584585
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Adjust a few things so that the sleepstates.asl file is the same for
sb/amd and soc/amd. These adjustments don't have a functional impact.
Change-Id: I0cc9462b326cdc371ffdbf5759d8adc42456ce74
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74960
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit cbc5d3f34b87db779829eabc90c32780a3865a56 ("soc/intel: Don't
report _S1 state when unsupported") added the `ACPI_S1_NOT_SUPPORTED`
option and commit 0eb5974def63a2fc0dce6dfdad62b0b4c6f4b865 ("acpigen:
Add a runtime method to override exposed _Sx sleep states") added a
mechanism to override the enabled sleep states at runtime. However,
these were only hooked up to Intel sleepstates. so the options would
not have any effect on AMD platforms.
Apply the changes from these two commits to AMD sleepstates so that
both options can be used on AMD platforms as well.
Change-Id: I7d5ef2361e36659ac5c6f54b2c236d48713a07c9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74959
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: Iaf88f34cedd09e2461bb05050392e178ec84d5d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I914a7f665e246e7490c127078a5a9795c8334d92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
The patch disables Tccold Handshake to prevent possible display
flicker issue for marasov board. Please refer to Intel doc#723158
for more information.
BUG=b:279117758
BRANCH=firmware-brya-14505.B
TEST=Boot to OS on marasov.
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I286e88e5bec240d64e6c801648f6483ad2b0939c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74931
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
