| Age | Commit message (Collapse) | Author |
|---|
|
This change removes all the separate entrypoint dispatch
functions as they all share the same pattern.
Furthermore, none of the function definitions under vendorcode
binaryPI/AGESA.c file have proper declarations, the ones compiler
picks up from AGESA.h are for the internal implementations and
with sanely organized headerfiles would not be exposed outside
the build of AGESA at all.
Change-Id: I0b72badc007565740c93b58743cfd048e8b42775
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31485
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IASL reports warning 'Control Method should be made Serialized'.
Change _CRS method to Serialized.
BUG=N/A
TEST=Build Intel Strago
Change-Id: I63a7e1caab19360a9a5831458311d5a83fdf52d1
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Due to PCB limitations the SD-Card interface is not able to operate
with the highest frequency reliably. The OS driver will switch to
the highest mode if a SD-Card is attached which supports this high
frequency mode. In order to work around this PCB limitation disable the
high frequency modes in the controller capabilities (SDR104 and HS400
mode) and leave SDR50 and DDR50 enabled.
Change-Id: Ia5fed5fb70b027de34170b49620927614a00fb7a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
References to MAINBOARD_PCI_SUBSYSTEM_{DEVICE_ID,VENDOR_ID} were removed.
Change-Id: I70ef22aac165a19663749f76449907482b761316
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32605
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The entry for drivers/intel/fsp1_0/Kconfig was added under the
chipset menu before addtional FSP versions were added, and the
drivers/*/*/Kconfig entry added to support them. This results
in the fsp1_0 Kconfig items being duplicated in the Chipset and
Generic Drivers menus.
Remove the chipset entry since it's no longer needed.
Test: select FSP 1.0 mainboard (e.g. intel/minnowmax) in menuconfig,
observe FSP 1.0 Kconfig entries listed only under Generic Drivers menu.
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Change-Id: If1e78fb9259b1a46d308db829881eb3b3d17cf40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32565
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=N/A
TEST=N/A
Change-Id: I1b207e0b77bac8860ba7501378297c1f3604141c
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32453
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IASL reports warning 'Control Method should be made Serialized'.
Change _CRS method to Serialized.
BUG=N/A
TEST=Build Google Banon and Google Cyan
Change-Id: Iffa097a2100cfa91efa3b617311500b83f839bce
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
CB acts as I/O handler for QCLib (e.g. DDR training data)
This interface allows bi-directional data flow between
CB and QCLib
Tested and working interfaces:
DDR Training data
QCLib serial console output
DDR Information (base & size)
limits cfg data
TEST=build & run
Change-Id: I073186674a1a593547d1ee1d15c7cd4fd8ad5bc1
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/25208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
TEST=build & run
Change-Id: I222a56f1c9b74856a1e1ff8132bab5e041672c5d
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/25207
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that support has been added for using the public FSP
repo for Braswell platform, clean up Kconfig options and
set sane defaults when using it.
The following changes have been made:
- add option to use the 3rdparty/fsp repo for Braswell platform
- reorder FSP 1.1 Kconfig entries for improved flow/readability
- set the default path for the FSP binary based on use of FSP
repo and platform
- set the CBFS location for the FSP binary based on platform
Change-Id: Ie2f732bf0ac4d4551908caa56360b8bb2869b4c7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The current Braswell FSP 1.1 header in vendorcode/intel, for
which there is no publicly available FSP binary, contains silicon
init UPDs which are not found in the publicly available header/binary
in the FSP Github repo. This prevents new boards from being added
which use the public Braswell FSP header/binary.
To resolve this, move the UPDs not found in the public header from
the soc's chip.c to ramstage.c for the boards which use them. Add
a Kconfig option to use the current non-public FSP header and
select it for boards which need it (google/cyan variants); set the
public FSP option as the default. Use the Kconfig option to set
FSP_HEADER_PATH to ensure the correct header is used.
Test: build google/cyan and intel/strago using non-public and
public FSP header/binaries respectively.
Change-Id: I43cf18b98c844175a87b61fdbe4b0b24484e5702
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Rather than selectively update the fsp submodule based on
FSP version or platform selection, update it when building
for any FSP-enabled platform, so all have latest version available.
Change-Id: If07d55828a1863623e04a4ecdd1514c3cb6d9c11
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Enable acoustic noise mitgation for arcada platform,
the slow slew rates for Ia and Gt are fast time dived by 8.
BUG=b:131144464
TEST=waveform test and hardware validation result pass.
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Change-Id: I395b2fc527705ab207325cfd7147e6af5f300fce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Main objective for this change is to export the bluetooth reset
gpio to the kernel for use in an rf-kill operation.
To do so, we enable USB acpi and define all of the USB2 devices,
which includes bluetooth's reset gpio information.
BUG=b:122540489
BRANCH=None
TEST=emerge-atlas coreboot chromeos-bootimage
$cat sys/firmware/acpi/tables/SSDT > /tmp/ssdt.dat &
retrieve ssdt.dat from DUT &
$iasl -d ./ssdt.dat & check the HS03 node is with "reset-gpio"
under _DSD object
Change-Id: I411ef707782655361bd1b8ac2b914b8ae64defeb
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Caveh Jalali <caveh@google.com>
|
|
Change-Id: I115e065ce11946b85571e7233203be68c1789d70
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch adds code to initialize two USB DWC3.0 controllers
and its associated QUSB V2 10nm PHYs to the SDM845 SOC, and uses them to
initialize USB3.0 on the cheza mainboard.
Synopsis controller initialization and configuration sequences taken from
USB 3.0 HPG chapter 2.2 and refer PHY HPG chapter 10.2 for QUSB phy
programming.
Includes Super speed mode support.
TEST=USB keypad and mass-storage device enumeration tested with this patch
Change-Id: I475a7757239acb8ef22a4d61afd59b304a7f0acc
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/25213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: I38d086c379a3c2f54d1603a2fed5b33860f7f4d7
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: Idebbbd89de05d949e6f953aa49d8662d64383d1a
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch selects EC_ACPI kconfig to identify Intel Ice Lake
RVP board by querying EC.
Change-Id: I0082e04ef1b21d533e40d232209ee630f748aec6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
This implementation corrects the GPE DWx mapping for GPIO groups.
The assignments is done in GPIO MISCFG register for all GPIO communities.
And configures the which GPIO communities get register as Tier1.
Change-Id: I9c306d46e5194944def26c24cdb95f5ebada42b8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
This patch ports CB:32275 changes from CNL to ICL.
Ice Lake require that FSP-M component should be
XIP. This change selects FSP_M_XIP so that the right arguments are
passed into cbfstool when adding this component.
Change-Id: Icc5550f1f94957fa1b28c8bba6fc0efee98e233e
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32507
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch ports CB:31787 and CB:31908 changes from CNL to ICL.
This change moves soc_fill_power_state and soc_prev_sleep_state to
pmutil.c. It allows the functions to be used across romstage and smm.
Also fix GEN_PMCON bit checks as below:
ICL PCH has PWR_FLR, SUS_PWR_FLR and HOST_RST_STS bits in GEN_PMCON_A
and so this change updates the check for these bits to use GEN_PMCON_A
instead of GEN_PMCON_B.
Change-Id: Ib7ab95b7bbcc97a076d27a11db2105f7b976b521
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32506
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch removes unused pch_log_state() function declaration from pch.h
because elog.c has static implementation of pch_log_state().
Change-Id: Ib0f3831dc3b60af2ee432a76866e401a51b96fb7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32505
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch ports CB:30718 and CB:31908 changes from CNL to ICL.
Add logging of chipset events on boot into the flash event log.
This was tested on a google/dragonegg board to ensure that events
like "System Reset" are added to the log as expected.
Also fix GEN_PMCON bit checks as below:
ICL PCH has PWR_FLR, SUS_PWR_FLR and HOST_RST_STS bits in GEN_PMCON_A
and so this change updates the check for these bits to use GEN_PMCON_A
instead of GEN_PMCON_B.
Change-Id: I25ec32e81f8801f8d5e69c6095ffed73d75dded6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32504
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
This patch ports CB:31902 changes from CNL to ICL.
The prev_sleep_state value was showing 5 even after warm reboot, once the
SUS_PWR_FLR bit is being set. This bit was not being cleared.
Hence clearing the PMCON status bits.
Change-Id: Ia07aa17b4491216a277c36edfe6ed2aa489287c6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32503
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit 351e3e5 ("src: Use include <console/console.h> when appropriate")
has broken the build here, see below, so we include console.h here again.
In file included from src/device/oprom/x86emu/x86emui.h:65,
from src/device/oprom/x86emu/debug.c:40:
src/device/oprom/x86emu/debug.c: In function 'x86emu_dump_regs':
src/device/oprom/x86emu/debug.h:46:22: error: implicit declaration of function 'printk'; did you mean 'printf'?
[-Werror=implicit-function-declaration]
#define printf(x...) printk(BIOS_DEBUG, x)
^~~~~~
src/device/oprom/x86emu/debug.c:366:5: note: in expansion of macro 'printf'
printf("\tAX=%04x ", M.x86.R_AX );
^~~~~~
Fixes: 351e3e5 ("src: Use include <console/console.h> when appropriate")
Change-Id: I75d0b7c08bfa6dcb07778bbb762223b62cfc3da7
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Chromebook doesn't require support wake on LAN in S5.
Disable it by default for power saving.
BUG=b:131571666
TEST= check LAN indicator is off under S5
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia90c9d2f3ea9b3580e9a7bbfb47c917dd51e3c03
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
a 1M CBFS size is inadequate when adding the FSP binary to
image due to default FSP location in CBFS, so bump to 2M
to ensure autobuilds succeed.
Change-Id: I0683bea43cc71fad32bc42bfbd72f3913256d53c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32525
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
DMA remapping structure flags settings are Bit 0: INTR_REMAP, Bit 1:
X2APIC_OPT_OUT, Bit 2: DMA_CTRL_PLATFORM_OPT_IN_FLAG, Bits 3-7:
Reserved (0).
BUG=b:130351429
TEST=Image built and kernel booted to kernel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Iaf4764a9062756cadc335d1932b0da8628797f5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32516
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For GPIO pads that are configured as no-connect (PAD_NC), setting it
as GPI (with Rx enabled) leads to GPE0_STS being set
incorrectly. Though this is not an issue in practice (GPE0_EN is not
set, so no events triggered), it can confuse users when debugging GPE
related issues.
This change configures PAD_NC to have Rx disabled along with Tx to
ensure that it does not end up setting GPE0_STS bits for unwanted
GPIO pads.
P.S.: IOSSTATE config does not have a TxDRxD setting, so leaving that
configuration as is.
BUG=b:129235068
TEST=Verified that GPE0_STS bits are not set for pads that are marked
as PAD_NC.
Change-Id: I726cc7b86a94e7449352cd8a8806d4d775c593dc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
|
|
* MSI MS-7707 V1.1 (Medion OEM Akoya P4385D MSN10014555)
* SandyBridge Intel P67 (BD82x6x)
* Winbond 25Q32BV (4MB)
* Fintek F71808A
* Intel 82579V Gigabit
* NEC uPD720200 USB 3.0 Host Controller
* IME 7.0.4.1197
Working:
* PCIe gfx adapter
* PS/2 Keyboard
* USB3.0
* Ethernet
* S0/S3/S5
* HWM
Change-Id: I999149bb95d553ed217b2288cc34bce4fe88abb3
Signed-off-by: Max Blau <tripleshiftone@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Add more registers and make them optional, so they keep untouched/
their default if omitted.
Change-Id: I5d8008176d2972976b387c558658b8e70b50af8e
Signed-off-by: Max Blau <tripleshiftone@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Increase ramstage to 2M, required to actually embed the 7.2mb uImage
into the coreboot.rom, increase the postram cbfs cache in order for the
fit image to be loadable (without this increase the fit payload is found
but not loaded)
Change-Id: Iee0ed9f7958588ceda54bb32253c84cac68abea2
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The name OPROM is somewhat inaccurate, since other steps to bring
up display and graphics are needed depending on mainboard/SoC.
This patch cleans up OPROM code nomenclature, and works towards
the goal of deprecating vboot1:
* Rename CONFIG_VBOOT_OPROM_MATTERS to
CONFIG_VBOOT_MUST_REQUEST_DISPLAY and clarify Kconfig
description
* Remove function vboot_handoff_skip_display_init
* Remove use of the VbInit oflag VB_INIT_OUT_ENABLE_DISPLAY
* Add |flags| field to vboot_working_data struct
* Create VBOOT_FLAG_DISPLAY_REQUESTED and set in vboot_handoff
BUG=b:124141368, b:124192753, chromium:948529
TEST=make clean && make test-abuild
TEST=build and flash eve device; attempt loading dev/rec modes
BRANCH=none
Change-Id: Idf111a533c3953448b4b9084885a9a65a2432a8b
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Patch corrects IRQ and GPIO configuration for RT5682 codec's Jack INT.
Switching IOAPIC to GpioInt because ACPI Interrupt() doesn't support
jack triggering on both edges.
BUG=b:130180492
TEST=build and boot on a CML EVT board.
Use evtest & verify headset jack detection functions as expected.
Change-Id: Ia9bf8d554b54554f9ac1e78fd44a508964c8a14d
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Suggested-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32474
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Describe the Firmware Interface Table and reference useful documentation.
Change-Id: I00abc1fd13be7b48d56ba8cb65d2542ed07f9017
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Use already defined system_reset() function.
Change-Id: I6e5aff96e06830931acf700593d3e1689857efdc
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Use already defined system_reset() function.
Change-Id: Ieff4271c4a09d564d5f3415d8bc2c3843c8460f2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use already defined system_reset() function.
Change-Id: I68ff4cffa2bfab6a15299795c3e1837fc9b85806
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use already defined system_reset() function.
Change-Id: I32c731de0c30940d15fd01fec6f10b3b33c04370
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use already defined system_reset() and full_reset() functions.
Change-Id: Ib7e399b5186aa704d0388c4a4b18480f2e3799f3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use already defined system_reset() function.
Change-Id: I436f62c4402736fb74c59d8b359d0b3963f0e659
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use already defined system_reset() and full_reset() functions.
Change-Id: I0a05f3ac5c5340a509024de2b444960f498c3e99
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Trusted Firmware places some components in SRAM on RK3399 and therefore
restricts accesses to SRAM to the secure world. This makes the vboot
working data inaccessible to normal world payloads, so we need to
migrate it into CBMEM.
Change-Id: Ic7c95790f2f118ccbdd897550f13b5f987bdd831
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
Implement mt_pll_raise_ca53_freq() in MT8183 to raise the CPU frequency.
Move the function declaration to common header.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: Ide8d767486d68177fa2bfbcc5b559879eca1bcda
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
With the default CPU voltage (0.8v), CPU frequency should be 1417Mhz at
most. We have to raise CPU frequency to 1989MHz after increasing CPU
voltage to 1.05v in romstage.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: I4c3e0fa27ccda8e0efe422b6ab503a1efb1697e9
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
NEED_VB20_INTERNALS should always be specified when peeking
into vboot internal data structures.
BUG=b:124141368, chromium:956474
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I5a47a28350fd5a68efeff0d06ca150c1ae145412
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Disable the GBB flag forcing manual recovery now that we can read
the manual recovery from H1.
Enable the GBB flag to skip EC software sync, since images built
from coreboot.org do not include the EC binaries by default.
Change-Id: I0e1d6304e3e29eda68c7b807cf0774275c37d710
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 9aae51ad1141a47d5c2f7133b02f5f0ab6168860.
Proper code in cpu/intel/common/ shall be used instead.
Change-Id: I4a5d558b03497d106083eece10c5b34e0e7cbb2d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29683
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We do not want the RX signal to be floating on the board as that could
cause the ISH to remain in a higher power state (because there is logic
to keep the ISH in an higher power state when there is an active UART).
Add an internal 20K pull up on the RX line. In normal configuration this
will burn an additional 544uW.
BRANCH=R75
BUG=b:131241969
TEST=verify that ISH console still works with rework
Change-Id: Ifc9621bcafe4c86edfa9cd6d58b307254d3a81ca
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
If the Intel IGD device pci 02.0 is disabled or undefined in
the device tree, then internal graphics pre-allocated memory
and GFX-VT MMIO memory for virtualization won`t be allocated
in the SoC address space.
Thus, patch resolves the FSP-S hang problem on Skylake/ Kaby
Lake processors when the IGD device is disabled. This should
provide to run FSP 2.0-based coreboot on these CPUs families
without integrated graphics card.
The following boards were used for testing:
- Asrock H110M-DVS board (desktop i5-6600) & NVIDIA GTX 1060
as external GPU.
Virtualization and GFX 3D acceleration with nouveau driver
still works well (tested on VirtualBox 5.1.38 with Ubuntu
18.04.1 as guest and host OS)
- Intel KBL-R U RVP board (mobile i5-8350u) without GFX.
Payload: tianocore edk2-stable201811-216-g51be9d0.
Change-Id: Id7a0cba582d83e3fe7e8d20342ee219cdd369a53
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32467
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable audio clock, intbus clock, infra clock and mtkaif
26m clock.Needed by audio playback in firmware.
BUG=b:117254418
BRANCH=none
TEST=Build pass and verified on kukui p1 board
Change-Id: I88060d9796cc23ad7f524943f36869e1ec85073d
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
This patch adds the setting of psys_pmax to 136W. According to the
design, Rpsys is 11.8Kohm. Here is the equation to come out the
Psys_pmax value: Psys_pmax * 1.493uA/W * 11.8Kohm / 2 = 1.2V
Hence, Psys_pmax is 136W.
BUG=b:124792558
BRANCH=None
TEST=emerge-sarien coreboot chromeos-bootimage & Ensure the value is
passed to FSP by enabling FSP log & Boot into the OS
Change-Id: Id3f6be5f0c2346a7763195a992c0ae45faede056
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Clear the GPI Interrupt Status & Enable registers to prevent any
interrupt storms due to GPI.
BUG=b:130593883
BRANCH=octopus
TEST=Ensure that the Interrupt status & enable registers are reset
during the boot up when the system is brought out of G3, S5 & S3. Ensure
that the system boots fine to ChromeOS.
Change-Id: Ia3b9d3bf08472219348e20b53bae470c589039fb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support to reset the GPI Interrupt Status & Enable registers so that
the system does not experience any interrupt storm from a GPI when it
comes out of one of the sleep states.
BUG=b:130593883
BRANCH=None
TEST=Ensure that the Interrupt status & enable registers are reset
during the boot up. Ensure that the system boots fine to ChromeOS.
Change-Id: I99f36d88cbab8bb75f12ab1a4d06437f837841cb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add the offset information for GPI interrupt status and enable register
in the pad_community structure. Populate the concerned information for
individual SoCs. This offset information is required to clear the
interrupt configuration during the bootup.
BUG=b:130593883
BRANCH=None
TEST=Ensure that the interrupt configuration are cleared during bootup.
Ensured that the system boots to ChromeOS.
Change-Id: I8af877a734e8d49b700d720b736da8764985a8f8
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We only grep'ed for "ACPI Warning" resulting in an actual more severe
"ACPI Error" being ignored.
Change-Id: I9cec8a388f5558b1ffc383cc2fc69405252cbb37
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Use already defined system_reset() function.
Change-Id: Ic4716a3bb1dc6c6b29a028fc0ab28f9195f08416
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32493
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The ACPI code of LPE device is included regardless of the
availability of the LPE controller.
Linux remains requesting the status of device LPEA even if
this device is disabled.
Include ACPI LPE controller code at Braswell mainboards with
LPE enabled.
BUG=N/A
TEST=Linux 4.17+ on Portwell PQ7-M107
Change-Id: Ic8acf9ea9e9b0ba9b272e20beb2023b7a4716a73
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
The dqs_map array is used only for LPDDR3 and LPDDR4. It is not used for
DDR4, and so it can be removed from the baseboard memory initialization
code.
BRANCH=none
BUG=b:129706819
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Change-Id: I07fac3097d68f37b4630d3f0010f987da2f03bd7
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32484
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
First configuration supported is 8 GB system memory:
4 x 2 GB (K4E6E304ED-EGCG).
BRANCH=none
BUG=b:129706819
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: Ibd92d585118ff75492e8a7188dcdb2a286836d56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Intel's DQ_DQS_RComp_Info_Utility generates data for 6 entries. MRC will
return errors if we don't have all 6 entries in the map.
BRANCH=none
BUG=b:131103736
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Change-Id: I20a768de0e4440d7dde7b717794c4e2d0c62819c
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Changes includes:
- enable TPM1 + add entry in devicetree
- configure LPC IO to make IPMI work + add entry in devicetree
- introduce DSDT and SMBIOS entries for IPMI to make it detectable
by ipmi_si driver
Signed-off-by: Lukasz Siudut <lsiudut@fb.com>
Change-Id: Ia975643064075f1f861f4ead6f24ed71f345ea04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Change-Id: I8bf81637f582373d9bba1d47fe5205d459151f3e
Signed-off-by: Daniel Maslowski <dan@orangecms.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32473
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Enable LTR for NVMe so it can use ASPM L1.2.
BUG=b:127593309
TEST=build and boot on sarien and check L1 substate with lspci
before: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2- ASPM_L1.1+
after: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
Change-Id: I9842beda6767f758556747f83cfcedbd00612698
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
|
|
Remapping Hardware Status Affinity (RHSA) structure is applicable for
platforms supporting non-uniform memory. An ACPI Name-space Device
Declaration (ANDD) structure uniquely represents an ACPI name-space
enumerated device capable of issuing DMA requests in the platform.
Add RHSA and ANDD structures support for DMAR table generation.
BUG=b:130351429
TEST=Image built and booted to kernel
Change-Id: I042925a7c03831061870d9bca03f11bf25aeb3e7
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The IRQ tables don't support this path, so we shouldn't report presence
of the legacy PICs. As the _PIC method is optional and we ignore the
passed parameter anyway, drop it.
Change-Id: I51301a600e16f74fde00fdcb4595e1f47a52e207
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
|
|
Change-Id: Ic1fcbf4b54b7d0b5cda04ca9f7fc145050c867b8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: If3c9783ebc41c103c915788139d91644b805f397
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
This reverts commit 77fb3632a4a3d3004b3aa4950967be9164d9711d.
Reason for revert: This change inadvertently added a submodule.
Change-Id: I6cc2a3cd9d88986a2599a5ff2e5a066b1396a8c0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32472
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch revises the AC/DC loadline settings because some major
layout changes between proto and evt boards.
BUG=b:130740639
BRANCH=None
TEST=emerge-atlas coreboot chromeos-bootimage and boot to the OS.
Change-Id: Iea12c621e7fab427a0de8f43f0290bf01d0c5a09
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: caveh jalali <caveh@chromium.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
|
|
BUG=crbug:948241
TEST=Booted and decompiled the table
[000h 0000 4] Signature : "MCFG"
[004h 0004 4] Table Length : 0000003C
[008h 0008 1] Revision : 01
[009h 0009 1] Checksum : 15
[00Ah 0010 6] Oem ID : "COREv4"
[010h 0016 8] Oem Table ID : "COREBOOT"
[018h 0024 4] Oem Revision : 00000000
[01Ch 0028 4] Asl Compiler ID : "CORE"
[020h 0032 4] Asl Compiler Revision : 00000000
[024h 0036 8] Reserved : 0000000000000000
[02Ch 0044 8] Base Address : 00000000F8000000
[034h 0052 2] Segment Group Number : 0000
[036h 0054 1] Start Bus Number : 00
[037h 0055 1] End Bus Number : 40
[038h 0056 4] Reserved : 00000000
Change-Id: I46dc1959971af4685a7ffd285429175d6882ae86
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32445
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
CPU's featuring a non eviction mode cache the whole ROM.
Therefore XIP stages don't need to follow some alignment constraints.
Change-Id: I4a30f31baa0f90279c0690ceb6aefea6de461bd9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I4835ca3e20f2e53598bfc77b633aca946d3fde9c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I8d80084095912c30bfd8fc100bf27b522485a08a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ic6eb9c7dbfc5fde97f0f45f09431c617cb850c38
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
'param' variable is unused because 'printram' function only expands to
something in debug builds (not default ones).
Change-Id: I0cdf34cbb9aaed5045db5294eeefeaac642aeb1a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32428
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3b5092aa076b9693f78c86ffb9b99805696bb0bb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I143f3395a385e170cce0979707d6a7f61107f40b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ie81377a31e6527c5fd5aaea99f08527912e870a0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The `printram` function only expands to a value only in debug builds.
This isn't done in default builds.
Change-Id: Ic88c4cc730ae2d0d0718c7f71260cd2b45a3ddcd
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Idd339e324b833d2d024edb45e33c3d74af4473e8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ibdfbf1031130ff861c4313d1271d6ccb68bf8837
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Update submodule pointer to pull in newly-updated Braswell FSP.
Adjust FSP_FD_PATH for soc/cannonlake due to filename case change.
Change-Id: I02ee0d32fd4c04cd4971eff20fc5a7de3f9b07ec
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Add FP_RST_ODL to early GPIO table, configured as low, so that the FPMCU
will get reset when coreboot enters bootblock.
BUG=b:130229952
BRANCH=none
TEST=Compiles (no Hatch device w/FP to test)
Change-Id: I8a8d8cc2c560f6518337f7500575fdc2265b6347
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Lynx Point switched to doing mainboard-specific super I/O setup in the
bootblock with commit d893a2635fdd ("sb/intel/lynxpoint: Enable LPC/SIO
setup in bootblock"). The X10SLM+-F was added while that commit was in
review, and hence did not receive the necessary changes to SIO setup.
This patch has not been tested on hardware.
Change-Id: I7a648ec967dea2113cbbde1a93c1963ca6dd3c88
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
On EC end, we want to change this pin from push-pull to open-drain.
And since there is no external pull-up resistor on the board, we'll
have to configure this pin as internal-pull-up on AP end.
BUG=b:129306003
TEST=None
Change-Id: Ibc1f89fc25773220db009c6571400b01390dd756
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
FIT support takes more heap memory than most coreboot payloads.
Change-Id: Id17f25e94d97e937b0e9a9cee3dd1a8aef1d525d
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add common SoC config.
Disable PCIe WiFi.
Add digitizer.
Turn off native SD card interface.
No WWAN.
Add DA7219 driver to Kconfig.
BUG=b:130310626
BRANCH=none
TEST=compiles (no Hatch ref or Kohaku device to test)
Change-Id: I17d5ba6ce4ec412384e4a1678474b8d26499ba40
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Not all Hatch variants utilize the SoC's native SD card support. Move
the support to board-specific variants instead of the base device tree.
BUG=none
BRANCH=none
TEST=compiles (no Hatch device to test with)
Change-Id: Iae24114aad2c4d042c25da6f8cb740ccc8960082
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32417
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If override tree does not have any device, then the chip info
structure in it cannot be associated with the correct device and ends
up being added as a standalone chip info structure without any device
actually using it. This change prevents this condition by throwing an
error during compilation.
BUG=b:130342895
Change-Id: I7b8bb6b3228030a465976ca32ce8ef63f41365dd
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Similar to hatch(CB:32278), this change sets SerialIo
config for UART0 to PchSerialIoSkipInit to skip initialization in
FSP.
This change also adds a device to kohaku override tree to ensure that
the settings in it take effect.
BUG=b:130310626
Change-Id: Ia25b45811be26d55fc0019e4cd22eb7310b5a4c4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable acoustic noise mitgation for arcada platform,
the slow slew rates for Ia and Gt are fast time dived by 8.
BUG=b:131144464
TEST=waveform test and hardware validation result pass.
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Change-Id: I37315ecfa245fce3085e62d1566ff037d8aa8ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32403
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable the POWER_OFF_ON_CR50_UPDATE option on sarien/arcada. This is
needed so that platform properly boots after doing a Cr50 firmware
update when running on battery.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I0b687285eb95070eaffb68611a7d98eb8434ce2c
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Modify the POWER_OFF_ON_CR50_UPDATE Kconfig option so that specific
mainboard implementations can disable the option.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I3beefaae21de61e53ae232dbdc8ea9dbb2c78cd5
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Sarien during S0iX
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I48419132ba734f20ad5cf484c2dda609570a6dd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32330
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sarien will change Melfas from HID to I2C and change address from
0x10 to 0x34. So we don't need VPD to separate Elan and Melfas
anymore.
BUG=b:131194574
TEST=boot up and check no Melfas HID device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic002f61b226743e1c18dbdbc51ce8b733916d8a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32437
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We want to disable touch for non-touch sku. We can use
strap pin GPP_B4 to identify it is connected with touch
or not.
touch sku: GPP_B4 is low
non-touch sku: GPP_B4 is high
BUG=b:131132419
TEST=boot up and check no touch device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If6681262c25e4b01e061a8520e38905d40345509
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32438
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set CPU frequency from 1100MHz to 1989MHz to improve booting time.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: Id41c7ea8905c4db2537a5c32f96eb7c6b2c008ea
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32397
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The maximum CPU frequency is 1417MHz with current processor voltage
(0.8v). Set processor voltage to 1.05v for higher CPU frequency.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: I24ecdac2c85d3f012d9235449c0d727d727dc185
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
