| Age | Commit message (Collapse) | Author |
|---|
|
This patch sets the package power limit (PL1) value in RAPL MSR
and disables MMIO register. Added configurable PL1 override
parameter to leverage full TDP capacity.
BUG=chrome-os-partner:56922
TEST=webGL performance(fps) not impacted before and after S3.
Change-Id: I34208048a6d4a127e9b1267d2df043cb2c46cf77
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-on: https://review.coreboot.org/16884
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In FSP1.1 all the platform resets including global was handled
on its own without any intervention from coreboot.
In FSP2.0, any reset required will be notified to coreboot
and it is expected that coreboot will perform platform reset.
Hence, implement platform global reset hooks in coreboot. If Intel
ME is in non ERROR state then MEI message will able to perform
global reset else force global reset by writing 0x6 or 0xE to
0xCF9 port with PCH ETR3 register bit [20] set.
BUG=none
BRANCH=none
TEST=Verified platform global reset is working with MEI
message or writing to PCH ETR3.
Change-Id: I57e55caa6d20b15644bac686be8734d9652f21e5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16903
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
As per ME BWG, there are two mechanism to generate a Global
Reset (resets both host and Intel ME), one is through CF9h
IO write of 6h or Eh with "CF9h Global Reset" (CF9GR) bit set,
PMC PCI offset ACh[20]. Another is to issue the Global Reset
MEI message. Because any attempts to cause global reset without
synchronizing the two sides might cause unwanted side effects,
such as unwritten flash data that will get destroyed if the
host were to cause a global reset without informing Intel ME
firmware, the recommended method is to send a Global Reset MEI
message when the following conditions are met:
The PCH chipset firmware just needs to complete the Intel ME
Interface #1 initialization and check the Intel ME HFSTS state
if Intel ME is not in ERROR state and is accepting MEI commands
then firmware should be able to use Global Reset MEI message to
trigger global reset.
Furthermore, if Intel ME is in ERROR state, BIOS can use I/O 0xCF9
write of 0x06 or 0x0E command with PCH ETR3 register bit [20]
to perform the global reset.
BUG=none
BRANCH=none
TEST=Verified Global Reset MEI message is able to perform platform
global issue in ME good state.
Change-Id: If326a137eeadaa695668b76b84c510e12c546024
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16902
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch programs and enables BAR for ME (bus:0/
device:0x16/function:0) device to have early ME communication.
BUG=none
BRANCH=none
TEST=Verified Global Reset MEI message can able to perform platform
global reset during romstage.
Change-Id: I99ce0ccd42610112a361a48ba31168c9feaa0332
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/17016
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
VBOOT_EC_SLOW_UPDATE should be selected if EC_GOOGLE_CHROMEEC is used as
building coreboot with Chrome OS support & without Chrome EC gives a
build error in coreboot.
Change-Id: I77eed0e1bdc1ba49381b72e21b0e18f573cadff0
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17020
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The clearing of the PMC registers was not being called resulting
in state persisting across reboots. This state is queried and
events are added to the eventlog like 'RTC reset' events. However,
the RTC reset event is a one time thing so it should only be logged
once. Without the clearing of the state the event was logged on
every boot.
BUG=chrome-os-partner:58496
Change-Id: I60aa7102977c2b1775ab8c54d1c147737d2af5e2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17027
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
According to "G45: Volume 3: Display Register Intel ® 965G Express
Chipset Family and Intel ® G35 Express Chipset Graphics Controller" the
VSYNC end should start at bit 16. This is also how Linux (at least 4.4)
sets this register, which can be seen with intel-gpu-tools.
TESTED on Lenovo thinkpad X60 (it does not change anything).
Change-Id: Ie222ac13211a91c4fbc580e2bf9de0d973ea9a3a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17015
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Change-Id: I53ba5ba790ae683082e712dc0b92f1ac5bf27ddb
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16990
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Change-Id: Id5f3f7f25041189d137ef4daa9f63a3b478763bc
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16988
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I81ced8c6e02b00a3835e3b42c9cf2669b1b2bd3e
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
[jn: Added XGCC_BIN variable to avoid requiring the tools in $PATH]
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16955
Tested-by: build bot (Jenkins)
|
|
The pointers printed on unaligned memory accesses are now aligned to
those printed at the end of print_trap_information.
Change-Id: Ifec1cb639036ce61b81fe8d0a9b14c00d5b2781a
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16983
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On other architectures, the serial ports aren't mapped at 0x3f8.
WIP: I'm not sure how exactly the dependency should be encoded in
Kconfig.
Change-Id: Ia1de545325a53607f62d08e76b2f61b25edbe6ef
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16982
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
TEST=Compiled for and ran on spike; it booted as before.
Change-Id: Id173643a3571962406f9191db248b206235dca35
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16995
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Id30463d1809d0a31c9d3825642dce66f3ab2750d
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16986
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
spike_util.h:
- (LOG_)REGBYTES and STORE are already defined in
arch/riscv/include/bits.h.
- TOHOST_CMD, FROMHOST_* are helper macros for the deprecated
Host-Target Interface (HTIF).
qemu_util.c:
- mcall_query_memory now uses mprv_write_ulong instead of first
translating the address and then accessing it normally. Thus,
translate_address isn't used anymore.
- Several functions used the deprecated HTIF CSRs mtohost/mfromhost.
They have mostly been replaced by stub implementations.
- htif_interrupt and testPrint were unused and have been deleted.
spike_util.c:
- translate_address and testPrint were unused and have been deleted.
After this commit, spike_util.c and qemu_util.c are exactly the same and
can be moved to a common location.
Change-Id: I1789bad8bbab964c3f2f0480de8d97588c68ceaf
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16985
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I277cc9ae22cd33f2cd9ded808960349d09e8670d
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/16984
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There is no code which uses the backup space in TPM created for vboot
nvram.
All chromebooks currently supported at the trunk store vboot nvram
in flash directly or as a backup.
BUG=chrome-os-partner:47915
BRANCH=none
TEST=emerge-samus coreboot
Change-Id: I9445dfd822826d668b3bfed8ca50dc9386f2b2b0
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5cee2d54c96ad7952af2a2c1f773ba09c5248f41
Original-Change-Id: Ied0cec0ed489df3b39f6b9afd3941f804557944f
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/395507
Original-Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://review.coreboot.org/16997
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch adds '--includes' option to 'git config --global' command
to allow user name and email to be defined in a file included from
the global gitconfig (~/.gitconfig) file.
BUG=none
BRANCH=none
TEST=make gitconfig with ~/.gitconfig including another file which
defines user.name and email.
Change-Id: I4fe61078b143c3a2e26b0be69c3ca8e6f069d8b0
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/16912
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This enables viewing more than ~20 files in the file list on the left.
Arrows are added to indicate that more items are available off-screen.
This mimics what was done in pci_module.
Change-Id: Idd1363e1abe98ba51c795879db061cc54808da8e
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Reviewed-on: https://review.coreboot.org/14546
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Regardless of the payload chosen a file etc/ps2-keyboard-spinup
is added to cbfs. With this fix this file is only added to cbfs when
seabios is choses as a payload.
Change-Id: I37cf4c998856db2d297356776752643dba46a8f8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16146
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Some devices have no LVDS output but if no VGA is connected or
no EDID can be found, it will try to init LVDS.
This patch detects the presence of an LVDS panel and makes sure that
LVDS is not initialized when it is absent.
Change-Id: Ie15631514535bab6c881c1f52e9edbfb8aaa5db7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16513
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The CPU_MICROCODE_BLOB_CBFS_LOC should only be specified for COREBOOT CBFS,
not for other CBFS.
BUG=none
BRANCH=none
TEST=Built and boot kunimitsu
Change-Id: I58bb289e6c9add2647876ef817b7920f6e7b427a
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16932
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This reuses linux code (at least 4.1) to compute the graphic clock
divisors for LVDS displays on the gm45 northbridge.
The divisors m1, m2, n, p1, p2 need to be such that
"BASE_FREQUECY * (5 * (m1 + 2) + (m2 + 2)) / (n + 2)
/ (p1 * p2)" is as close as possible to the target_frequency.
On g4x hardware the BASE_FREQUENCY is 96000kHz.
This potentially increases LVDS display compatibility.
Change-Id: I2323af5756431e89769f95059790f5a922af14b4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16741
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I2b8c4ef75cca9f9d5251789cda4187a02076b69d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16964
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Requesting low power acpi cpu c-states has two software interfaces:
Using P_LVLx I/O reads or using equivalent MWAIT requests.
This change makes it more consistent with newer targets that use MWAIT
requests.
There also exists extended intel acpi c-states which can be enabled
in two ways:
- using a substate hint to the mwait request (defined in bios);
- setting a model specific register (msr)
Currently this is done by setting the right msr bits but with this
change one can experiment by adding substate hints.
Change-Id: I9eeb5b008e2ddc2193725667f2c13582a4877e3c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14801
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ice4a5cae1a289852895012bb55035707b54cefb5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16899
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I81c32c618627507cc3a83f60f565a73e5e6d7a13
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16913
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I0014fc030888d71f7951c97bccc7cef0e1c45186
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16922
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
MHCBAR(CLKCFG) was previously incorrectly written by the
sdram_program_memory_frequency function which required falsely
limiting the max dram frequency for 945GC.
TESTED on Intel d945gclf (memclock 667 and fsb 533) and
Gigabyte ga-945gcm-s2l (memclock 667 and fsb 1067)
Change-Id: I520efd69fa09fc9fde87c5301fd81121fde6a700
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16940
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
An epic battle to fix Nehalem finally ended when we found an odd mask
set in SMRR. This was caused by a wrong calculation of TSEG size. It
was assumed that TSEG spans the whole space between TSEG base
and GTT. This is wrong as TSEG base might have been aligned down.
TEST: On X201, copied 1GiB from usb key to sd-card and verified.
Change-Id: Id8c8a656446f092629fe2517f043e3c6d0f1b6b7
Found-by: Alexander Couzens, Nico Huber
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/16939
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I3213a8664955239b10bcf1784ce1ba5e0d95688b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16958
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
gerrit-rebase is a gerrit-context aware rebase script. Given a source
and a target branch (that need to have a common ancestor), it prepares
a rebase todo list that applies all commits from source that aren't
already found on target.
It matches commits using Reviewed-on lines in the commit message that
are added by gerrit when submitting commits using the "cherry-pick"
strategy.
This has been shown to be the best preserved meta data to work from in
existing data (Change-Id was mangled in all kinds of ways).
Change-Id: I9618c1b66ebc1fb7ed006efbc1665fb08386e1a5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/16695
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch adds MAINBOARD_HAS_NATIVE_VGA_INIT_TEXTMODECFG to the
gigabyte/ga-g41m-es2l Kconfig to allow selecting between textmode and
vesamode in menuconfig.
Change-Id: I84b61118fa0419d49d2498b66029711cdce97576
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16501
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch implements native resolution, VESA mode, on the VGA output of
x4x.
It relies on EDID to modeset, but has a fallback-mode (640 x 480 @
60Hz) if this is no EDID could be found. This fallback mode only works
in textmode since in VESA mode some payloads (grub2) rely on VBE info,
which is being generated from an EDID.
Change-Id: I247ea7171ba3c5dc3b209d00e4dcb2d2069abd75
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16498
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
flashrom treats them as invalid because start > end.
Change-Id: I1c8b4563094823ebd9b1193b91e7b4a748955228
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/16936
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ib44bc66e02901dbde14361091a049f71c3ecb840
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16921
Tested-by: build bot (Jenkins)
Reviewed-by: Kerry Sheh <shekairui@gmail.com>
|
|
Change-Id: I416d3c212653260a28cb07ed86fda34b736ba4ca
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16926
Tested-by: build bot (Jenkins)
Reviewed-by: Kerry Sheh <shekairui@gmail.com>
|
|
Maxim98357a speaker amp requires BCLK & SFRM to be active
and stable before it is unmuted. If there is a BLCK and no
SFRM, it results in a pop sound.
sdmode_delay property already exists which facilitates this
configuration. This patch updates "sdmode_delay" to avoid
pop sound.
BUG=chrome-os-partner:58356
BRANCH=None
TEST=while audio playback via headset, remove headset.
Audio will be switched playback to speaker. Observe if
pop sound comes from speaker.
Change-Id: I7ad68caa88d7b3ff52ac1379fe6564de27d97777
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/16933
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
It's `.git/modules/3rdparty/blobs` now.
Change-Id: Ief12bb934332375a20f150afb568aef266924c9f
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/16946
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Change-Id: I2d40049a27f725f14acbc16438f0e6ea7cdd7329
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16879
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I0dd8c32f1b9165fe8c449cee1c21a155a725c04f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16878
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I53a0344686921012f4e031842b5108aa4a7b79b1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16908
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ia1e7f558bbc44001358339a522e59a2ef7c420fb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16923
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The datasheets "Intel® Core™ Duo Processor and Intel® Core™ Solo
Processor on 65 nm Process" mentions cpu C-states substates which can
either be attained by adding a substate hint to the MWAIT/P_LVLx request
or automatically by setting some msr bits correctly.
This just sets the same msr bits as model_6fx to enable
dynamic L2 cache, C2E and C4E acpi cpu states.
The result is that when limiting a thinkpad x60 with a yonah T2400
cpu to the acpi cpu C2 state, the idle power usage drops from 18W to
14W. When the lowest C-state is set to C4 the idle power usage seems
to remain similar.
Change-Id: I6c422656ace04659f32082a5944617eda6c79ec3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16901
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ic589b26c6c94df12e1fe218d079018db8b38fbd9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16898
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: If372655700c18340d51368a39392560f664f4a45
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16896
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I04fe6b7a8798d0f3cb54130283ce5a50eb9ac5b4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16895
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ifd6aefa6c046d100a5388a24a7d23cbd77905a85
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16893
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Testing: booted successfully.
Change-Id: I4a50c9fb7aec929ea29a3cf2eec3e424e3629c92
Signed-off-by: Hakim Giydan <hgiydan@marvell.com>
Reviewed-on: https://review.coreboot.org/16692
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I37c1674ee380936aba797e24897593fcca3b0269
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16891
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I930c761b9a2422590af3a0a5008b4ff2abe3fd96
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16890
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I2a52db28353f8575d11218af936b4a233fd05f77
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16889
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ic22f8a00e6009e104df8c4374067369ebbf90ee2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16888
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I5f45a4cd5661140f57aa37e86cc8a34622da3de5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16887
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I7966f996a4291cc6b97b53aba59b43358de94e45
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16886
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I63fee62253cb0488a041c9985a646102261b8c5e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16880
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I71a12235196d478673d2816a9ee64f1373f3a63d
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/16935
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
max_regions is set to the maximal regions based on the ifd version
Change-Id: I9fa5a4565f4dbd67b5c6df97756311560e2a18bc
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/16934
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
When timestamp is enabled, the system hangs because the timestamp data
is not yet available. Add a temporary work around that starts the
timestamp after the FspInit() making this data available.
Verified on Intel Camelback Mountain CRB and ensured that system can
boot to payload with timpstamp feature enabled.
Change-Id: I59c4bb83ae7e166cceca34988d5a392e5a831afa
Signed-off-by: York Yang <york.yang@intel.com>
Reviewed-on: https://review.coreboot.org/16894
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The enforced FSP 1.0 APIs call was used to work around an fsp1.0 driver
issue. As the issue has been addressed in fsp1.0 driver (Change 9780),
remove the enforced workaround. Otherwise will see error message
'FSP API NotifyPhase failed' in serial log.
Verified on Intel Camelback Mountain CRB and confirmed that the serial
log error message regarding the 'FSP API NotifyPhase failed' is gone.
Change-Id: Iafa1d22e2476769fd841a3ebaa1ab4f9713c6c39
Signed-off-by: York Yang <york.yang@intel.com>
Reviewed-on: https://review.coreboot.org/16892
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
When compiling a non-x86 platform with DRIVERS_INTEL_WIFI enabled,
we get the build error:
src/drivers/intel/wifi/wifi.c:17:30: fatal error:
arch/acpi_device.h: No such file or directory
acpi_device.h only exists in the x86 architecture directory.
Change-Id: Id0e29558336bf44e638cfcb97c22f31683ea4ec7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16906
Tested-by: build bot (Jenkins)
Reviewed-by: Antonello Dettori <dev@dettori.io>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
|
|
Some PVT units encountered DRAM calibration failure during
power on/off tests. The failure is caused by higher impedance
of the DRAM on those units. So increase the driving strength
for 4GB DRAMs.
BUG=chrome-os-partner:57392
TEST=run cold reboot 100 times on PVT units which have DRAM
calibration issue.
Change-Id: I8a329093db3f1def566e4b7afec3c4f4bfe44c6a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cf1aa5ade856af433fa056f51a20d18553ae241d
Original-Change-Id: I0d1776cd1a5892d1f82e9bf414620d1ef6d29132
Original-Signed-off-by: PH Hsu <ph.hsu@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/394451
Original-Commit-Ready: Yidi Lin <yidi.lin@mediatek.com>
Original-Tested-by: Yidi Lin <yidi.lin@mediatek.com>
Original-Reviewed-by: Pin-Huan Hsu <ph.hsu@mediatek.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/16917
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We found that Kevin board PHY0 and PHY1 eye-diagram margin
is not enough to make compliance test pass, and the PHY0 USB
SI is worse than PHY1, because of the higher PCB impedance.
For PHY0, we can't improve the eye-diagram by SW PHY tuning,
so we need to reduce the RBIAS resistance from 133 ohm to 115
ohm, it can help to increase the eye-height.
For PHY1, we can improve the eye-diagram by setting the max
pre-emphasis level.
And after the above change, the USB2 signal amplitude will
become larger at the test point near to SOC USB2 PHY, in order
to avoid mis-trigger the disconnect detection (650mV), we need
to disable pre-emphasize in eop state.
BRANCH=None
BUG=chrome-os-partner:53863
TEST=do USB 2.0 compliance test for Kevin C0 and C1 port.
Change-Id: I95c0acd79623aeca9a0ae077b1dd3836d91fe561
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: de3cdef128966d76e7d8e2ebd641763b911c3ad5
Original-Change-Id: I00cb325b9938e4276cc77b5d6f5faa7023379608
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/390615
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16911
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Though we don't use Type-C PHY to support USB3 in firmware,
we still need to initialize the Type-C PHY, and make sure
the power state of pipe is always fixed to U2/P2. After
this, we can force USB3 controller to work in USB2 only
mode.
BRANCH=none
BUG=chrome-os-partner:56425
TEST=Go to recovery mode, plug a Type-C USB drive containing
chrome OS image into both ports in all orientations, check if
system can boot from USB.
Change-Id: I95bb96ff27d4fecafb7b2b9e9dc2839b5c132654
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8ec98507845276119d8a9d5626934dedcb35f2dd
Original-Change-Id: Ie3654cd1c1cb76b62aa9b247879b60cbecee0155
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/391412
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16910
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We do this so that the riscv objdump can be used on the coreboot.elf file.
Change-Id: Ib8bf85a3299dd75b779e7fa3757f5b62c9c7170b
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/16918
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
Converged Security Engine (CSE) has a secure variable storage feature.
However, this storage is expected to be reset during S3 resume flow.
Since coreboot does not use secure storage feature, disable HECI2 reset
request. This saves appr. 130ms of resume time.
BUG=chrome-os-partner:56941
BRANCH=none
TEST=powerd_dbus_suspend; resume; check time with cbmem -t. Note
FspMemoryInit time is not significantly different from normal boot
time case.
Change-Id: I485a980369c6bd97c43b9e554d65ee89e84d8233
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/16870
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
These header files contain a few new UPDs. The EnableS3Heci2
UPD will be used to save ~100ms from the S3 resume time on
Apollolake chrome platforms.
BUG=chrome-os-partner:58121
BRANCH=none
TEST=built coreboot for reef and verified no regressions
Change-Id: I1f324d00237c7150697800258a2f7b7eed856417
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/16869
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
commit 028200f7 - x86/acpi_device: Add support for GPIO output polarity
updated ACPI_GPIO_OUTPUT to ACPI_GPIO_OUTPUT_ACTIVE_HIGH for the other
boards that needed it, but pyro wasn't in the tree when it was initially
pushed. Now that pyro is in the tree, it needs to be updated as well.
Change-Id: I617999b06ee584e0543d7ae3232bb2be2ff7429c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16930
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
Between GNU Tar 1.28 & 1.29, the files excluded by --exclude-vcs was
updated. This breaks the reproducibility. Instead, just manually
exclude the files to match what was excluded in v 1.28 and earlier.
Change-Id: Ie0717891506f4a6d750ff264f9cc2494a296265b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16900
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
- Add more help text.
- Remove braces from variables where the variable is isolated.
- Remove --recurse-submodules from clone. This breaks on old coreboot
versions.
- Add some whitespace between blocks.
- Fix all shellcheck warnings.
- Verify tar version and fail if it doesn't support --sort.
Change-Id: I4a49df99532d9a92a4a05bceff16f96a4fc3e205
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16883
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch enables stage cache to save ~40ms during S3 resume.
It saves ramstage in the stage cache and restores it on resume
so that ramstage does not have to reinitialize during the
resume flow. Stage cache functionality is added to postcar stage
since ramstage is called from postcar.
BUG=chrome-os-partner:56941
BRANCH=none
TEST=built for Reef and tested ramstage being cached
Change-Id: I1551fd0faca536bd8c8656f0a8ec7f900aae1f72
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/16833
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ibcac5dd60dc7da82bbeeb89ac445a5a1aa56ed3d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16852
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ia2fc3d5ea88d61ba7c4a1daebfe74a24948c8f6e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16865
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I0903b7ca9eada4beacfcdbcacddec23c3515651e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16850
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ic3b599d49a4c03ad8035c558b975f31cb91d253b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16862
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I5585eac9fec5180254c7d3cc966441e9794e8390
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16858
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: If79eb706b6d44f7c34dfe31a1545f5850870b334
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16866
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ie2a047d35e69182812c349daedc5b3b5fde20122
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16860
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I35cb7e08d5233aa5a3dbb4631ab2ee4dc9596f98
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16849
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Instead of hard-coding the polarity of the GPIO to active high/low,
accept it as a parameter in devicetree. This polarity can then be used
while calling into acpi_dp_add_gpio to determine the active low status
correctly.
BUG=chrome-os-partner:55988
BRANCH=None
TEST=Verified that correct polarity is set for reset-gpio on reef.
Change-Id: I4aba4bb8bd61799962deaaa11307c0c5be112919
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/16877
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Only acpi_dp of type DP_TYPE_TABLE is allowed to be an array. This
DP_TYPE_TABLE does not have a value which is written. Thus,
acpi_dp_write_array needs to start counting from the next element type
in the array. Fix this by updating the initialization in for loop for
writing array elements.
BUG=chrome-os-partner:55988
BRANCH=None
TEST=Verified that the correct number of elements are passed for
add_gpio in maxim sdmode-gpio.
Change-Id: I8e1e540d66086971de2edf0bb83494d3b1dbd176
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/16871
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Some Chrome OS ECs require a small amount of time after a SPI
transaction to reset their controllers before they can service the next
CS assertion. The kernel and depthcharge have always enforced a 200us
minimum delay for this... coreboot should've done the same.
BRANCH=gru
BUG=chrome-os-partner:58046
TEST=Booted Kevin in recovery mode, confirmed that recovery events got
logged with correct timestamps in eventlog.
Change-Id: I32ec343f3293ac93729d3e6e2f43d7605a396cdb
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b9e4696533d4318ae7c8715b71ab963d8897c16c
Original-Change-Id: I6a7baf7859d5d50e299495d118e7890dcaa2c1b0
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/392206
Original-Tested-by: Shawn N <shawnn@chromium.org>
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-on: https://review.coreboot.org/16885
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
GPIO1_B3 (WLAN_MODULE_RST#) defaults as a pull-up input, but it is also
"pulled up" by 1.8V_WLAN. However, 1.8V_WLAN remains low for some time
during early boot. This leaves the signal floating somewhere in the
middle.
This has two potential issues:
(1) we're leaking some power for some (hopefully) short period of time
(2) we are possibly screwing with the Wifi power sequence; we aren't
supposed to deassert PDn (i.e., MODULE_RST#) until all the rails
have fully ramped for some period of time
Neither of the above issues are likely to be significant, but it is nice
to fix, I expect.
BRANCH=gru
BUG=chrome-os-partner:54026
TEST=measure WLAN_MODULE_RST# on scope at boot time
Change-Id: Ia6af9ad6954ad8feeda33015e3f205842380939e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0e890a2787bf034d3358a33fc88c2dd8078593ab
Original-Change-Id: I120e26ad0ca486a326874986e142dcaee965b62d
Original-Signed-off-by: Brian Norris <briannorris@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/388009
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16882
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This reverts commit 28821dbb2261267462a7e9b0cc1c23b51af2d3ee.
(https://review.coreboot.org/16649)
This change causes the kernel to boot really slow. Maybe there is an
interrupt storm that prevents the kernel from making any
progress. Reverting until the proper kernel dependency is met.
BUG=chrome-os-partner:57364
BRANCH=None
TEST=Kernels boots to prompt fine on DVT.
Change-Id: I1c9913b4476a08303f9dd887b8631601c847dcf7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d7014ee1bb88df7a2d7f6b3dced797fef75b252d
Original-Change-Id: I061c0b03b43b516a190b370c04888e73a410fcf1
Original-Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/391233
Original-Reviewed-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/16881
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:31690391
TEST=Tested with board ID
BRANCH=none
Change-Id: I9a2b7eec111a79827f72a506942a8ec833ba7e60
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f23e2b6e72491aaafa15774f9bded3e14363abbc
Original-Change-Id: I23183db29d7f7dd812e94ab6a1f2f1329c46ac60
Original-Signed-off-by: Kan Yan <kyan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/388778
Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org>
Original-Reviewed-by: Suresh Rajashekara <sureshraj@chromium.org>
Reviewed-on: https://review.coreboot.org/16770
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
CL:377541 was supposed to remove the big CPU cluster initialization from
rkclk_init() in the bootblock and move it to a more suitable place in
ramstage. Except that next to all the code cleanup I did in that patch,
I seem to have forgotten to actually remove that old code.
Big thanks to Nico for spotting that in the upstream coreboot review.
BRANCH=gru
BUG=chrome-os-partner:54906
TEST=Booted Kevin.
Change-Id: I09fe948b4587536802b42329b813177439e0804f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 77f9eaf0446b22adfca79d0adf8a0ecfd93c0040
Original-Change-Id: I13dab208225b7e43ad864f2f3cf51b3c104acd4b
Original-Reported-by: Nico Huber <nico.h@gmx.de>
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/389236
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16769
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This selects the rank to train before training is triggered. This is
to prevent any race conditions with the hardware.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=stressapptest -M 1536 -s 1000
Change-Id: I892bace414cf4495619d41bdaea0c4e91c1e29b3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8f2dd6f52978a9e54ddd2688eb68fd237aabfe2d
Original-Change-Id: I4e7118d8509b59e391d0a254477b5390dfdd43a5
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/387907
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: 云平 汤 <typ@rock-chips.com>
Reviewed-on: https://review.coreboot.org/16768
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
UX Doc = go/gale-hw-ui
This color wasn't changed earlier as the change wasn't done in
the OS also. However, since we cannot change this later in FW
(but OS can change anytime), I am making this change after discussing
with the UX team.
BUG=b:31501528, b:31633562
TEST=Change the device state to 'recovery mode' to observe the new
color.
BRANCH=none
Change-Id: Ia91f14eb77492095cb41a9de0bb9790e72aa4851
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 36a3d8c6eabbc0b23d0a15d5bddc5ed3bdeebe70
Original-Change-Id: I88768b94cf91804a6005e44b1a168e059698ec4b
Original-Signed-off-by: Suresh Rajashekara <sureshraj@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/388206
Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org>
Original-Tested-by: Suresh Rajashekara <sureshraj@chromium.org>
Original-Reviewed-by: Christopher Book <cbook@chromium.org>
Original-Reviewed-by: Kan Yan <kyan@google.com>
Reviewed-on: https://review.coreboot.org/16767
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There are two modifications in the driver:
1. Correctly set speeds based on DDR frequency.
Control the speeds in the predriver circuits to reduce power.
SPEED[1:0]
2'b00:less than 800Mbps(400MHz)
2b01 : 800Mbps(400MHz) to 1600Mbps(800MHz)
2b10 : 1600Mbsp(800MHz) to 2400Mbps(1200MHz)
2b11 : 3200Mbps and greater
2. Configure the number of cycles for the phy clock pll wait time after
locking, based on the DDR config file.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=do memtester on kevin board, and pass
Change-Id: Iaf6da59c6c5c290867e0922a2a99de272f4c7bde
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 125cf8afac3a682d33896fe74a20ba1d498a3bd2
Original-Change-Id: Iabc17df37a701c4f052540c3c259f209a1db3c59
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/387428
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16722
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I8997e927d82363921a3ff17580b9a575acc1ce16
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/16919
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
PHY_PER_CS_TRAINING is being enabled when DDR frequency >= 666.
For per cs training, the controller should consider the PHY
delay line switch time and there should be more cycles to
switch the delay line, so update the W2W_DIFFCS_DLY_ value
from 0x1 to 0x5.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=do memtester on kevin board, and pass
Change-Id: I00df2d4724b0b77f3e7565809fb35bbd2ff01ea5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c135ea3e33d810ed322d947eb8d512d1ac119cfc
Original-Change-Id: I81b99cbc085769b7028e770509d79bd8d550820b
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/387506
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16721
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
To save power when entering suspend, gpios 2 to 4 need to be set
to input and 'pull none' mode.
Pass the APIO configuration to ATF so it can do a proper job here.
BRANCH=None
BUG=chrome-os-partner:56423
TEST=run suspend_stress_test on kevin board
Change-Id: Id57fe8f622ae3f9c2bc7e58be89518b2b846cd37
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9c42082d1ca9a6baa735821382d3e83c1f8dc9ad
Original-Change-Id: Iaf441e8e34c5591ffe7c65f6533fcf0b733ff5ac
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/378475
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16720
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We need to disable some regulators when the device goes into suspend.
This means that we need to pass some gpios to bl31, and disable these
gpios when bl31 runs the suspend function.
BRANCH=None
BUG=chrome-os-partner:56423
TEST=enter suspend, measure suspend gpio go to low
[pg: also update arm-trusted-firmware to match]
Change-Id: Ia0835e16f7e65de6dd24a892241f0af542ec5b4b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0f3332ef2136fd93f7faad579386ba5af003cf70
Original-Change-Id: I03d0407e0ef035823519a997534dcfea078a7ccd
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/374046
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16719
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Create the initial Pyro variant which refers to the Reef.
Pyro is APL Chrome board that deviate from reference board Reef.
BRANCH=master
BUG=None
TEST=Build
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Change-Id: I9beed1f6895e8891d3d51b563edfe172f566718b
Reviewed-on: https://review.coreboot.org/16855
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Colors and patterns as defined by the UX team
BUG=b:31501528
TEST=Move the device to different states in FW using rec and dev
button and verify the colors
BRANCH=None
Change-Id: I66d41a54590cd3ce4e5202c7cfa890f462fe195e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 703559d5dddaeeb7d435d6cadbb2009a1b7a76c8
Original-Change-Id: I95ab1fa59b483396ff1498a28f1ee98ac08d02d7
Original-Signed-off-by: Suresh Rajashekara <sureshraj@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/387258
Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org>
Original-Tested-by: Suresh Rajashekara <sureshraj@chromium.org>
Original-Reviewed-by: Christopher Book <cbook@chromium.org>
Original-Reviewed-by: Kan Yan <kyan@google.com>
Reviewed-on: https://review.coreboot.org/16718
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In USB2 only mode, the Type-C PHY will be held in reset and
only the USB2 logic of the USB3 OTG controller and PHY will be
used over the USB2 pins on the Type-C connector to support Low,
Full and High-speed USB operation.
BRANCH=none
BUG=chrome-os-partner:56425
TEST=Go to recovery mode, plug a Type-C USB drive containing
chrome OS image into both ports in all orientations, check if
system can boot from USB.
Change-Id: Ic265c0c91c24f63b2f9c3106eb2bb277a589233b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a37ccc5b6019967483eac6b5a360d67bc3326e93
Original-Change-Id: I582f04f84eef447ff0ba691ce60e9461ed31cfad
Original-Signed-off-by: Liangfeng Wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/385837
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16717
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
To improve sdram 800MHz and 933MHz stability, we
need to modify write leveling flow to get the
proper write leveling value.
BUG=chrome-os-partner:56940
BRANCH=none
TEST=Boot from kevin on 933MHz, and do stressapptest
Change-Id: I5b24c93d4a57917fb9af7e5e2a95d8423ccbaa7e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d84bf25b3e5de373c7913e6d534a810cb984b3fd
Original-Change-Id: I87efddf628c3683fcb85d6875e029cf3cbc482be
Original-Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Original-Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/384292
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16716
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since there's currently a limitation in coreboot's code that prevents
more than 4KB to be used by the eventlog anyway, this patch shrinks the
available RW_ELOG area in the FMAP for Gru down to 4KB. This may prove
prudent later if we ever resolve that limitation, so that tools can rely
on the area in the FMAP being the same as the area actually used by the
read-only firmware code on these boards.
BRANCH=gru
BUG=chrome-os-partner:55593
TEST=Booted Kevin, confirmed that eventlog got written normally. Ran a
reboot loop to exhaust eventlog space, confirmed that the shrink code
kicks in as expected before reaching 4KB.
Change-Id: I3c55d836c72486665a19783fe98ce9e0df174b6d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 05efb82ca00703fd92d925ebf717738e37295c18
Original-Change-Id: Ia2617681f9394e953f5beb4abf419fe8d97e6d3e
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/384585
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Simon Glass <sjg@google.com>
Reviewed-on: https://review.coreboot.org/16715
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We found that we may want to load some components of BL31 on the RK3399
into SRAM. As usual, these components may not overlap any coreboot
regions still in use at that time, as is already statically checked by
the check-ramstage-overlaps rule in Makefile.inc.
On RK3399, the only such regions are TTB and STACK. This patch moves the
TTB region back to the end of SRAM (right before STACK), so that a large
contiguous region of SRAM before that remains usable for BL31.
BRANCH=gru
BUG=None
TEST=Booted Kevin.
Change-Id: I1689d0280d79bad805fea5fc3759c2ae3ba24915
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1d4c6c6f6cc0efe97d6962a81e309a1c040d1def
Original-Change-Id: I37c94f2460ef63aec4526caabe58f35ae851bab0
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/384635
Original-Reviewed-by: Simon Glass <sjg@google.com>
Reviewed-on: https://review.coreboot.org/16714
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
sdram noc timing will affect ddr latency, this patch improves
rk3399 sdram noc timing so improve memory performance.
BRANCH=gru
BUG=chrome-os-partner:57248
TEST=Boot from kevin board
Change-Id: I09e984490a7ad747ef8abfc6542d0e2c95ec19bc
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 43dfe55d713d371e39d21312772fd353614b7642
Original-Change-Id: I393e74ecdeb72930ac38ae9bcf311e5654f65162
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/382725
Original-Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Sonny Rao <sonnyrao@chromium.org>
Original-Commit-Queue: Sonny Rao <sonnyrao@chromium.org>
Reviewed-on: https://review.coreboot.org/16713
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
